11-28-FS-BD-16 - LEADER TECH-FERRISHIELD

Black = inches Red= mm

8-25FSC-XX-16 0.08 2.03 0.250 6.35 0.170 4.32 0.188 4.78 0.003 0.076 0.048 1.22 16 406 85 0.250

11-37FSC-XX-16 0.11 2.79 0.375 9.5 0.170 4.3 0.188 4.8 0.003 0.076 0.065 1.65 16 406 85 0.250

11-S-37FSC-XX-16 0.11 2.79 0.375 9.5 0.170 4.3 0.188 4.8 0.002 0.050 0.065 1.65 16 406 85 0.250

14-51FSC-XX-16 0.14 3.56 0.510 13.0 0.228 5.8 0.250 6.4 0.003 0.076 0.100 2.54 16 406 64 0.250

14-S-51FSC-XX-16 0.14 3.56 0.510 13.0 0.228 5.8 0.250 6.4 0.002 0.050 0.100 2.54 16 406 64 0.375

23-76FSC-XX-24 0.23 5.84 0.760 19.3 0.343 8.7 0.375 9.5 0.004 0.102 0.115 2.92 24 610 64 0.375

P/N A B Finger Pitch Mat. Thick Comp Height Length

Fingers

Tape

Copper Beryllium Fingerstock

Folded Series

Leader Tech's Folded Gasket series are industry standard general-purpose gaskets that allow a large range of deflection and

compression forces. These gaskets are available with or without tape for alternate attachment methods. Also available in a snag-

free version where, under compression, the leading edge of the gasket slides into an extended and folded base which prevents

possible damage to the gasket.

FS Folded Black = inches Red= mm

Order Toll-Free 1.866.TECH.EMI Fax 813.855.3291 Website www.leadertechinc.com

MOUNTING

OPTIONS

■ Tape

■ Solder

■ Rivet

The Leader Tech FS gaskets are industry standard general-purpose gaskets that allow a large

range of deflection and compression forces. These gaskets are available without tape for

alternate attachment methods. Consult factory for information.

XX - Select material/finish (See order information below)

Directional Force

11-28-FS-XX-16 0.11 2.79 0.28 7.11 0.170 4.32 0.188 4.78 0.003 0.076 0.24 5.842 0.37 9.4 0.065 1.65 16 406 85 0.145

11-S-28-FS-XX-16 0.11 2.79 0.28 7.11 0.170 4.32 0.188 4.78 0.002 0.050 0.24 5.842 0.37 9.4 0.065 1.65 16 406 85 0.145

14-37FS-XX-16 0.14 3.56 0.37 9.40 0.228 5.79 0.250 6.35 0.003 0.076 0.32 7.874 0.50 12.7 0.100 2.54 16 406 64 0.200

14-37FS-XX-300 0.14 3.56 0.37 9.40 0.228 5.84 0.250 6.35 0.003 0.076 0.32 7.874 0.50 12.7 0.100 2.54 300 7620 1200 0.200

14-S-37FS-XX-16 0.14 3.56 0.37 9.40 0.228 5.79 0.250 6.35 0.002 0.050 0.31 7.874 0.50 12.7 0.100 2.54 16 406 64 0.200

23-60FS-XX-24 0.23 5.84 0.60 15.24 0.343 8.71 0.375 9.53 0.004 0.102 0.50 12.700 0.77 19.6 0.115 2.92 24 610 64 0.250

23-S-60FS-XX-24 0.23 5.84 0.60 15.24 0.343 8.71 0.375 9.53 0.003 0.076 0.50 12.700 0.77 19.6 0.115 2.92 24 610 64 0.250

25-78FS-XX-24 0.25 6.35 0.78 19.81 0.335 8.51 0.375 9.53 0.005 0.127 0.53 13.462 0.94 23.9 0.115 2.92 24 610 64 0.375

25-78FS-XX-300 0.25 6.35 0.78 19.81 0.340 8.64 0.375 9.53 0.005 0.127 0.53 13.462 0.94 23.9 0.150 3.81 300 7620 800 0.375

25-S-78FS-XX-24 0.25 6.35 0.78 19.81 0.335 8.51 0.375 9.53 0.003 0.076 0.53 13.462 0.94 23.9 0.150 3.81 24 610 64 0.375

25-S-78FS-XX-300 0.25 6.35 0.78 19.81 0.335 8.51 0.375 9.53 0.003 0.076 0.53 13.462 0.94 23.9 0.150 3.81 300 7620 800 0.375

41-113FS-XX-12 0.41 10.41 1.13 28.78 0.460 11.68 0.500 12.57 0.007 0.178 0.80 20.320 1.94 49.3 0.230 .584 12 305 24 0.375

P/N A B Finger Pitch Mat. Thick C

Comp Length

Comp Height

Length Fingers Tape

FSC Folded

MOUNTING

OPTIONS

■ Tape

■ Solder

■ Rivet

The FSC was created to provide snag free gaskets with FS gasket features. The base of the gasket is

extended from the mounting area and then folded up, over, down, and then comes to rest over the

leading edge of the formed spring. Under compression, the leading edge of the gasket slides under

and is “captured.” This “no snag” feature is also used to prevent possible gasket damage.

XX - Select material/finish (See order information below)

Directional Force

FSV Folded Black = inches Red= mm Comp = Compressed

FSDS Folded Black = inches Red= mm Comp = Compressed

Folded Series (cont.)

MOUNTING

OPTIONS

■ Tape

■ Rivet

■ Weld

■ Solder

Directional

Force

The FSV is an FS gasket that has the base bent at a right angle to the curve of the spring form,

with all the other features of the FS gasket maintained. Tape optional - please consult factory.

XX - Select material/finish (See order information below)

11-28FSV23-XX-16 0.11 2.8 0.28 7.1 0.170 4.3 0.188 4.8 0.003 0.076 0.37 9.4 0.065 1.65 0.24 6.1 0.80 20.3 0.06 1.52 16 406 85

11-S-28FSV23-XX-16 0.11 2.8 0.28 7.1 0.170 4.3 0.188 4.8 0.002 0.051 0.37 9.4 0.065 1.65 0.24 6.1 0.80 20.3 0.06 1.52 16 406 85

14-37FSV30-XX-16 0.14 3.6 0.37 9.4 0.228 5.8 0.250 6.4 0.003 0.076 0.50 12.7 0.100 2.54 0.32 8.1 0.80 20.3 0.06 1.52 16 406 64

14-S-37FSV30-XX-16 0.14 3.6 0.37 9.4 0.228 5.8 0.250 6.4 0.002 0.051 0.50 12.7 0.100 2.54 0.32 8.1 0.80 20.3 0.06 1.52 16 406 64

23-60FSV50-XX-24 0.23 5.8 0.60 15.2 0.343 8.7 0.375 9.5 0.004 0.097 0.77 19.6 0.115 2.92 0.50 12.7 0.31 7.87 0.08 2.03 24 610 64

23-S-60FSV50-XX-24 0.23 5.8 0.60 15.2 0.343 8.7 0.375 9.5 0.002 0.051 0.77 19.6 0.115 2.92 0.50 12.7 0.31 7.87 0.08 2.03 24 610 64

25-78FSV50-XX-24 0.25 6.4 0.78 19.8 0.335 8.5 0.375 9.5 0.005 0.127 0.94 23.9 0.150 3.81 0.50 12.7 0.38 9.65 0.14 3.56 24 610 64

25-S-78FSV50-XX-24 0.25 6.4 0.78 19.8 0.335 8.5 0.375 9.5 0.003 0.076 0.94 23.9 0.150 3.81 0.50 12.7 0.38 9.65 0.14 3.56 24 610 64

41-113FSV-XX-12 0.41 10.41 1.13 28.70 0.460 11.68 0.500 12.7 0.007 0.178 0.750 19.05 0.380 9.65 0.80 20.32 0.56 14.2 0.14 3.56 12 305 24

P/N A B Finger Pitch

Mat. Thick

Comp Width Comp Height

Hole Spacing Hole Diameter

Length

Fingers

25-109FSDS-XX-24 0.25 6.4 1.09 27.7 0.335 8.5 0.375 9.5 1.27 32.26 0.150 3.81 0.16 4.06 .140 4.06 0.005 0.127 24 610 64

25-109FSDS-XX-300 0.25 6.4 1.09 27.7 0.335 8.5 0.375 9.5 1.27 32.26 0.150 3.81 0.16 4.06 .140 4.06 0.005 0.127 300 7620 800

25-S-109FSDS-XX-24 0.25 6.4 1.09 27.7 0.335 8.5 0.375 9.5 1.27 32.26 0.150 3.81 0.16 4.06 .140 4.06 0.003 0.076 24 610 64

25-S-109FSDS-XX-300 0.25 6.4 1.09 27.7 0.335 8.5 0.375 9.5 1.27 32.26 0.150 3.81 0.16 4.06 .140 4.06 0.003 0.076 300 7620 800

41-163FSDS-XX-24 0.41 10.4 1.63 41.4 0.460 11.7 0.500 12.7 1.90 48.26 0.230 5.84 0.19 4.83 .140 3.56 0.007 0.178 24 610 64

41-163FSDS-XX-300 0.41 10.4 1.63 41.4 0.460 11.7 0.500 12.7 1.90 48.26 0.230 5.84 0.19 4.83 .140 3.56 0.007 0.178 300 7620 800

P/N A B Finger Pitch

Comp Width Comp Height

C D Mat. Thick Length Fingers

The Leading Edge in EMI Shielding Technology

✔

RoHS

COMPLIANT

MOUNTING

OPTIONS

■ Tape

■ Rivet

■ Weld

■ Solder

Directional

Force

The FSDS is an FS gasket with its base lying on the same plane as the curve in the spring form,

with the mounting area shortened. This mounting is often modified for custom applications.

XX - Select material/finish (See order information below)

Copper Beryllium Fingerstock

Order Toll-Free 1.866.TECH.EMI Fax 813.855.3291 Website www.leadertechinc.com

When placing an order or requesting a quotation, please give part number,

your required finish I.D. from the chart below, and required length.

Leader Tech tape mounted CuBe gaskets offer pressure-sensitive, double-sided adhesive for strong bonding to

a wide variety of surface conditions. Ideal for all-purpose contact strips used in metal cabinets and electronic

enclosures and is unaffected by temperatures from -67 to +250°F (-55 to 121°C)

Simply follow these four easy steps:

1. Remove all grease and oily residue with a solvent such as isopropyl alcohol/water mixture (rubbing alcohol)

or heptane. Dry and smooth the mounting surface with emery cloth if necessary.

2. Peal off the protective paper backing from the pressure sensitive adhesive tape.

3. Place the gasket in correct position. Press firmly to ensure a good bond to surface. Avoid repositioning, which

might impair the effectiveness of the adhesive or may bend or kink the strip. NOTE: On strips where fingers

cover the solid portion of the gasket, pressure may be applied by inserting a mandrel in the strip and pressing

down.

4. At room temperature approximately 50% of the ultimate strength will be achieved after 20 minutes, 90% after 24

hours, and 100% after 72 hours. In some cases bond strength can be increased and ultimate bond strength can be

achieved more quickly by exposure of the bond to elevated temperature, e.g., 150°F (66°C) for 1 hour.

Adhesive Mounting of Fingerstock Gaskets

The above example is the “Slot Mount Series” gasket shown on page 3. The height is .11 inch and the width is .32

inch. The “-S-” indicates a soft gasket. The “SN” indicates a bright tin finish. See list below for available finishes. This

part is available in lengths of 16 inches. Consult factory for custom lengths or for availability in 25’ coils.

Part Number Example:

Stock Item Finish I.D. Length

11-S-32RH – SN – 16

Standard plating finish is .0001 inch (.0025 mm) minimum. Plating processes and thicknesses may be varied to meet

customer needs. Standard plating finish for gold is 0.00005 inches. See adjacent list of available finishes and consult

factory for additional options.

Ordering Information

Available Plating Finishes:

Finish Type Applicable Specifications Leader Tech Finish Code

Bright Finish - BD

Bright Tin ASTM B-545 SN

Satin/Matte Tin ASTM B-545 ST

Tin Lead SAE AMS-P-81728 / or as specified SNpb

Electro-less Nickel RoHS SAE AMS 2404 NI

Zinc/Chromate Clear ASTM B-633 / SAE AMS 2402 Zinc

Zinc/Chromate Yellow ASTM B-633 / SAE AMS 2402 ZincY

Cadmium Chromate As specified CdC

Bright Silver ASTM B-700 AG

Satin/Matte Silver ASTM B-700 MAG

Gold MIL-DTL-45204 / ASTM B-488 / SAE AMS 2422 AU

Solderable Unplated As specified SU