CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Radial Lead
CAT. No. E1001F
@Super low ESR, high ripple current capability
@Lower profi le than PSA (F8B8L to F10B12.5L)
@Rated voltage range : 2.5 to 16Vdc
@Nominal capacitance range : 330 to 2,700MF
@Endurance : 2,000 hours at 105C
@Suitable for DC-DC converters, voltage regulators and decoupling applications
for computer motherboards
@RoHS Compliant
?SPECIFICATIONS
(at 20C, 120Hz)
(at 105C)
(at 20C after 2 minutes)
(at 20C, 120Hz)
(at 100kHz)
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
*Note
Dissipation Factor
(tane)
Low Temperature
Characteristics
(Max.Impedance Ratio)
Endurance
Bias Humidity Test
Surge Voltage Test
Failure Rate
Items
-
55 to +105C
2.5 to 16Vdc
P20% (M)
Rated voltage(V)B1.15
I=0.2CV or 500MA, whichever is greater.
Where, I : Leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (Vdc)
0.10 max.
Z(
-
25C)/Z(+20C)[1.15
Z(
-
55C)/Z(+20C)[1.25
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 2,000 hours
at 105C.
Appearance No significant damage
Capacitance change [P20% of the initial value
D.F. (tanE)[150% of the initial specified value
ESR [150% of the initial specified value
Leakage current [The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to DC voltage at 60C,
90 to 95% RH for 1,000 hours.
Appearance No significant damage
Capacitance change [P20% of the initial value
D.F. (tanE)[150% of the initial specified value
ESR [150% of the initial specified value
Leakage current [The initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds
through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds.
Appearance No significant damage
Capacitance change [P20% of the initial value
D.F. (tanE)[150% of the initial specified value
ESR [150% of the initial specified value
Leakage current [The initial specified value
1% per 1,000 hours maximum (Confidence level 60% at 105C)
Characteristics
?DIMENSIONS [mm] ?MARKING
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 60 minutes at 105C.
Size code
fD
L
fd
F
L'
H08
8.0
8.0
0.6
3.5
L+1.0max.
HB5
8.0
11.5
0.8
3.5
JB5
10.0
11.5
0.8
5.0
JC5
10.0
12.5
0.6
5.0
L+1.5max.
Coated Case
L'
15min. 4min.
FD+0.5max.
Fd
FP0.5
C
3D6
820
2.5V
EX) 2.5V820MF
@Terminal Code : E
New!
(1/2)
ALUMINUM ELECTROLYTIC CAPACITORS
Precautions and Guidelines