IS31SE5100 8-CH CAPACITIVE TOUCH SENSOR WITH AUTO CALIBRATION March 2013 GENERAL DESCRIPTION FEATURES The IS31SE5100 is an ultra low power, fully integrated 8-channel solution for capacitive touch-buttons applications. The chip allows electrodes to project sense fields through any dielectric such as glass or plastic. On-chip calibration logic continuously monitors the environment and automatically adjusts on-and-off threshold levels to prevent false sensor activation. The IS31SE5100 supports the 400kHz IC serial bus data protocol and includes a field programmable slave address. An INTB is generated when a button event (touched or released) occurs, triggered and cleared condition could be configured by setting the interrupt register. IS31SE5100 is available in QFN-24 (4mm x 4mm) and SSOP-24 packages. It operates from 2.7V to 5.5V over the temperature range of -40C to +85C. APPLICATIONS Complete eight sensors capacitive touch controller for buttons Auto offset compensation Sensitivity adjustable by external capacitor or internal register Extremely low power optimized for portable application Interrupt output 400kHz fast-mode IC interface 8kV ESD HBM Operating temperature TA = -40C ~ +85C QFN-24 (4mm x 4mm) and SSOP-24 packages Mobile phones GPS PDAs TYPICAL APPLICATION CIRCUIT Figure 1 Typical Application Circuit Note 1: The IC should be placed far away from the mobile antenna in order to prevent the EMI. Note 2: The RS resistor should place as close as possible to reduce EMI. Integrated Silicon Solution, Inc. - www.issi.com Rev. C, 03/18/2013 1 IS31SE5100 PIN CONFIGURATION SSOP-24 19 GND 20 OUT4 21 OUT5 22 OUT6 CAP2 4 15 SDB CAP3 5 14 INTB CAP4 6 13 SDA AD 11 16 OUT1 SCL 12 CAP1 3 CAP8 10 17 OUT2 CAP7 9 18 OUT3 VCC 2 CAP6 8 GND 1 CAP5 7 QFN-24 23 OUT7 Pin Configuration (Top View) 24 OUT8 Package OUT6 1 24 OUT5 OUT7 2 23 OUT4 OUT8 3 22 GND GND 4 21 OUT3 VCC 5 20 OUT2 CAP1 6 19 OUT1 CAP2 7 18 SDB CAP3 8 17 INTB CAP4 9 16 SDA CAP8 10 15 SCL CAP5 11 14 AD CAP6 12 13 CAP7 Integrated Silicon Solution, Inc. - www.issi.com Rev. C, 03/18/2013 2 IS31SE5100 PIN DESCRIPTION No. Pin Description 4,22 GND Ground. 2 5 VCC Power supply. 3~10 6~9, 11~13,10 CAP1~CAP8 Input sense channel 1 ~ 8. Each channel should connect to GND if it is not used and disabled by the 01h register (Page 8). 11 14 AD I2C address setting. 12 15 SCL I2C serial clock. 13 16 SDA I2C serial data. 14 17 INTB Interrupt output, active low. 15 18 SDB Shutdown the chip when pulled low. 16~18 19~21 OUT1~OUT3 Channel 1 ~ 3 outputs. Pull low when input sense channel is pressed. Each channel should be floating if it is not used. 20~24 23,24, 1~3 OUT4~OUT8 Channel 4 ~ 8 outputs. Pull low when input sense channel is pressed. Each channel should be floating if it is not used. - Thermal Pad Connect to GND. QFN SSOP 1,19 Copyright (c) 2013 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless Integrated Silicon Solution, Inc. receives written assurance to its satisfaction, that: a.) the risk of injury or damage has been minimized; b.) the user assume all such risks; and c.) potential liability of Integrated Silicon Solution, Inc is adequately protected under the circumstances Integrated Silicon Solution, Inc. - www.issi.com Rev. C, 03/18/2013 3 IS31SE5100 ORDERING INFORMATION Industrial Range: -40C to +85C Order Part No. Package QTY IS31SE5100-QFLS2-TR QFN-24, Lead-free 2500/Reel IS31SE5100-SALS2 SSOP-24, Lead-free 58/Tube Integrated Silicon Solution, Inc. - www.issi.com Rev. C, 03/18/2013 4 IS31SE5100 ABSOLUTE MAXIMUM RATINGS Supply voltage, VCC Voltage at any input pin Maximum junction temperature, TJMAX Storage temperature range, TSTG Operating temperature range, TA -0.3V ~ +6.0V -0.3V ~ VCC+0.3V 150C -65C ~ +150C -40C ~ +85C Note: Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other condition beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS TA = 25C, VCC = 2.7V ~ 5.5V, unless otherwise noted. Typical value are TA = 25C, VCC = 3.6V. Symbol Parameter Condition Min. Typ. 2.7 Max. Unit 5.5 V VCC Supply voltage ICC Quiescent power supply current VSDB = VCC = 3.6V 11 175 345 A ISD Shutdown current VSDB = 0V, VCC = 5.5V 0 0.5 2.3 A VHR Current Sink headroom voltage IOUT = 20mA, VCC = 3.6V 218 312 412 mV CS Minimum detectable capacitance CS = 5pF (Note 1) 0.2 pF Logic Electrical Characteristics VIL Logic "0" input voltage VCC = 2.7V VIH Logic "1" input voltage VCC = 5.5V 0.4 IIL Logic "0" input current VINPUT = 0V(Note 1) 5 nA IIH Logic "1" input current VINPUT = VCC(Note 1) 5 nA 1.4 V V DIGITAL INPUT SWITCHING CHARACTERISTICS (Note 1) Symbol Parameter Condition Min. Typ. Max. Unit 400 kHz fSCL Serial-Clock frequency tBUF Bus free time between a STOP and a START condition 1.3 s tHD, STA Hold time (repeated) START condition 0.6 s tSU, STA Repeated START condition setup time 0.6 s tSU, STO STOP condition setup time 0.6 s tHD, DAT Data hold time tSU, DAT Data setup time 100 ns tLOW SCL clock low period 1.3 s tHIGH SCL clock high period 0.7 s 0.9 s tR Rise time of both SDA and SCL signals, receiving (Note 2) 20+0.1Cb 300 ns tF Fall time of both SDA and SCL signals, receiving (Note 2) 20+0.1Cb 300 ns Note 1: Guaranteed by design. Note 2: Cb = total capacitance of one bus line in pF. ISINK 6mA. tR and tF measured between 0.3 x VCC and 0.7 x VCC. Integrated Silicon Solution, Inc. - www.issi.com Rev. C, 03/18/2013 5 IS31SE5100 DETAILED DESCRIPTION The 8-bit chip address is sent next, most significant bit first. Each address bit must be stable while the SCL level is high. I2C INTERFACE The IS31SE5100 uses a serial bus, which conforms to the I2C protocol, to control the chip's functions with two wires: SCL and SDA. The IS31SE5100 has a 7-bit slave address (A7:A1), followed by the R/W bit, A0. Set A0 to "0" for a write command and set A0 to "1" for a read command. The value of bits A1 and A2 are decided by the connection of the AD pin. After the last bit of the chip address is sent, the master checks for the IS31SE5100's acknowledge. The master releases the SDA line high (through a pull-up resistor). Then the master sends an SCL pulse. If the IS31SE5100 has received the address correctly, then it holds the SDA line low during the SCL pulse. If the SDA line is not low, then the master should send a "STOP" signal (discussed later) and abort the transfer. The complete slave address is: Table 1 Slave Address Bit A7:A3 A2:A1 A0 Value 10001 AD 1/0 Following acknowledge of IS31SE5100, the register address byte is sent, most significant bit first. IS31SE5100 must generate another acknowledge indicating that the register address has been received. AD connected to GND, AD = 00; AD connected to VCC, AD = 11; AD connected to SCL, AD = 01; AD connected to SDA, AD = 10; Then 8-bit of data byte are sent next, most significant bit first. Each data bit should be valid while the SCL level is stable high. After the data byte is sent, the IS31SE5100 must generate another acknowledge to indicate that the data was received. The SCL line is uni-directional. The SDA line is bi-directional (open-collector) with a pull-up resistor (typically 4.7k). The maximum clock frequency specified by the I2C standard is 400kHz. In this discussion, the master is the microcontroller and the slave is the IS31SE5100. The "STOP" signal ends the transfer. To signal "STOP", the SDA signal goes high while the SCL signal is high. READING PORT REGISTERS To read the device data, the bus master must first send The timing diagram for the I2C is shown in Figure 2. The SDA is latched in on the stable high level of the SCL. When there is no interface activity, the SDA line should be held high. ____ the IS31SE5100 address with the R/W bit set to "0", followed by the command byte, which determines which register is accessed. After a restart, the bus master must then send the IS31SE5100 address with The "START" signal is generated by lowering the SDA signal while the SCL signal is high. The start signal will alert all devices attached to the I2C bus to check the incoming address against their own chip address. Figure 2 ____ the R/W bit set to "1". Data from the register defined by the command byte is then sent from the IS31SE5100 to the master (Figure 5). Interface timing Figure 3 Integrated Silicon Solution, Inc. - www.issi.com Rev. C, 03/18/2013 Bit transfer 6 IS31SE5100 Figure 4 Writing to IS31SE5100 Figure 5 Integrated Silicon Solution, Inc. - www.issi.com Rev. C, 03/18/2013 Reading from IS31SE5100 7 IS31SE5100 Table 2 Register Function Address Name Function Table Default 00h Configuration Register Set software shutdown mode and sensitivity 3 0000 0000 01h Channel Control Register Set the 8 channels enable 4 1111 1111 02h State Register 1 Store state of action for 8 channels 5 03h State Register 2 Show state of 8 channels changes or not 6 04h Interrupt Register Set interrupt function 7 Table 3 00h Configuration Register Table 5 02h State Register 1 (Read only) Bit D7 D6:D5 D4:D0 Bit D7:D0 Name SSD SS - Name AS8: AS1 Default 0 00 00000 Default 0000 0000 The Configuration Register sets software shutdown mode and sensitivity. The State Register 1 stores state of action for 8 channels. SSD 0 1 Software Shutdown Enable Normal operation Software shutdown mode ASx 0 1 SS 00 01 10 11 Sensitivity Selection Normal sensitivity High sensitivity Low sensitivity Not a valid state Table 6 03h Table 4 01h Channel Control Register Bit D7:D0 Name CH8: CH1 Default 1111 1111 The Channel Control Register sets the 8 channels enable. CHx 0 1 Channel Enable Disable Enable 0000 0000 Action State Bit Button released Button pressed State Register 2 (Read only) Bit D7:D1 Name SC8: SC1 Default 0000 0000 The State Register 2 shows state of 8 channels changes or not. State Change Bit No state change Button touched or released event occurs SCx 0 1 Table 7 04h Interrupt Register Bit D7:D6 D5:D0 Name ACI - Default 00 000000 The Interrupt Register sets interrupt function. ACI 00 01 10 11 Integrated Silicon Solution, Inc. - www.issi.com Rev. C, 03/18/2013 Automatically Clear Interrupt No auto clear Auto clear after 8ms Auto clear after 32ms Not a valid state 8 IS31SE5100 FUNCTIONAL BLOCK DIAGRAM Integrated Silicon Solution, Inc. - www.issi.com Rev. C, 03/18/2013 9 IS31SE5100 TYPICAL APPLICATION GENERAL DESCRIPTION INTERRUPTION The IS31SE5100 is an ultra low power, fully integrated 8-channel solution for capacitive touch-buttons applications. The chip allows electrodes to project sense fields through any dielectric such as glass or plastic. The changing of action can be signed by the INTB pin. The INTB pin will be pulled low when sensitivity channel is pressed or released. And the MCU can get the information via reading the Status Register (02h, 03h). The INTB will be back to high until the MCU reading the Status Register 2 (03h). SENSITIVITY ADJUSTING Sensitivity can be adjusted by the external capacitor or internal register. The value of capacitor is higher the sensitivity is lower; value of capacitor is lower the sensitivity is higher. The SS bit of Configuration Register (00h) is used to modulate sensitivity. By setting the SS bit to "00" sensitivity is normal. Sensitivity is high when SS bit is set to "01". Sensitivity is low when SS bit is set to "10". Setting SS bit to "11" is not a valid state. OUTPUT CONTROL There are 8 output ports for 8 sensitivity channels. The corresponding output will be pulled low to drive LED or other device if sensitivity channel is pressed. For example, in Figure 1, when some sensitivity channels are pressed, the corresponding LEDs will be light up. ACTION INFORMATION The action information is stored in the State Register (02h, 03h). If the AS bit is set to "0", the corresponding channel is released. If the AS bit is set to "1", the corresponding channels is pressed. If the SC bit is set to "0", the corresponding channel has no status changing. If the SC bit is set to "1", the corresponding channel has status changing. Integrated Silicon Solution, Inc. - www.issi.com Rev. C, 03/18/2013 The ACI bit of Interrupt Register (04h) is used to configure the automatically interrupt function. If the ACI bit is set to "00", the automatically interrupt function disable. If the ACI bit is set to "01", the function enable and he INTB pin will be high automatically when it stays low last 8ms. If the ACI bit is set to "10", the INTB pin will be high automatically when it stays low last 32ms. Setting ACI bit to "11" is not a valid state. SHUTDOWN MODE Shutdown mode can be used as a means of reducing power consumption. During shutdown mode all registers retain their data. SOFTWARE SHUTDOWN By setting SSD bit of the Configuration Register (00h) to "1", the IS31SE5100 will operate in software shutdown mode. HARDWARE SHUTDOWN The chip enters hardware shutdown mode when the SDB pin is pulled low, wherein they consume only 0.5A (typ.) current. 10 IS31SE5100 CLASSIFICATION REFLOW PROFILES Profile Feature Pb-Free Assembly Preheat & Soak Temperature min (Tsmin) Temperature max (Tsmax) Time (Tsmin to Tsmax) (ts) 150C 200C 60-120 seconds Average ramp-up rate (Tsmax to Tp) 3C/second max. Liquidous temperature (TL) Time at liquidous (tL) 217C 60-150 seconds Peak package body temperature (Tp)* Max 260C Time (tp)** within 5C of the specified classification temperature (Tc) Max 30 seconds Average ramp-down rate (Tp to Tsmax) 6C/second max. Time 25C to peak temperature 8 minutes max. Figure 6 Classification profile Integrated Silicon Solution, Inc. - www.issi.com Rev. C, 03/18/2013 11 IS31SE5100 PACKAGE INFORMATION QFN-24 Integrated Silicon Solution, Inc. - www.issi.com Rev. C, 03/18/2013 12 IS31SE5100 SSOP-24 Note: All dimensions in millimeters unless otherwise stated. Integrated Silicon Solution, Inc. - www.issi.com Rev. C, 03/18/2013 13 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: ISSI: IS31SE5100-QFLS2-TR IS31SE5100-SALS2