RK09L 9mm Size Metal Shaft Snap-in Type Single-unit and dual-unit types suit a variety of controls Typical Specifications Items Specifications Total resistance tolerance 20 Maximum operating voltage 50V AC, 10V DC Rotary Potentiometers Total rotational angle 3005 Slide Potentiometers Rotational torque 2 to 25mNm Operating life 15,000 cycles Operating temperature range -10 to 70 Product Line Number of resistor elements Mounting direction Shaft type Length of the shaft L1mm Metal Shaft 15 Horizontal type Center detent Total resistance Resistance Minimumorder unitpcs. k taper Japan Export Without 10 15A With 20 1B 20 Insulated Shaft 12.5 Single-unit 20 Knob Operating 25 Flat Horizontal type for tone Without With 15 Through Shaft Type Horizontal type for vol. Vertical type for tone Ring Type Vertical type for vol. 1 RK09L1140A5E RK09L1140A66 10 RK09L1140A5P RK09L1140A2U 1,000 2,000 RK09L1140A65 50 RK09L122002M 100 RK09L1220A1B 50 15A RK09L12B0A31 10 3B RK09L12B0A3Z With 50 Without 10 20 1B 15A 2 RK09L114001T 1B 5 20 15 15A Without 25 15 RK09L112003P RK09L1120A69 50 With Drawing No. RK09L1120A2S Without 15 Vertical type Dual-unit 10 Products No. 3 RK09L124000Z RK09L1240A12 RK09L12D0A1W 4 RK09L12D0A1T Note Other varieties are also available. Refer to "Other Specifications" (P.308). Packing Specifications Tray Number of packagespcs. 306 1 case /Japan 1 case /export packing Export package measurements mm 1,000 2,000 479x369x181 Refer to P.308 for other specifications. Refer to P.308 for attached parts. Refer to P.309 for ordering products not listed. Refer to P.343 for soldering conditions. RK09L9mm Size Metal Shaft Snap-in Type Dimensions No. Unit:mm Photo Single-shaft, single-unit Horizontal type RK09L1120 PC board mounting hole dimensions Viewed from mounting side Style L1 LB R1 15 5 7 20 7 12 4.1 Rotary Potentiometers 5 R 5 11.3 1.8 1 Mounting surface 3-o1 hole 1.1 Slide Potentiometers x Single-shaft, single-unit Vertical type RK09L1140 L1 12.5 LB 5 R1 7 15 5 7 20 7 12 25 7 12 11.3 1.8 1.1 5 Metal Shaft 7.5 R 2 3-o1 hole 15 5 7 25 7 12 3.3 5 2.5 11.3 3 1.8 R 5 L1 LB R1 Knob Operating Single-shaft, dual-unit Horizontal type RK09L1220For tone RK09L12B0For vol. Insulated Shaft x Through Shaft Type Mounting surface 6-o1 hole 1.1 x L1 LB R1 15 5 7 20 7 12 Ring Type 11.3 1.8 2.5 5 7.5 R 1.1 4 Single-shaft, dual-unit Vertical type RK09L1240 For tone RK09L12D0 For vol. 6-o1 hole x Dimensions of Bushing and Fixing Lug Unit:mm G 307 9mm Size Metal Shaft Snap-in Type / Other Specifications In addition to the products listed, we can accommodate the follow specifications. Total Resistance Variety Total resistancek 5 10 20 50 100 Resistance Taper Rotary Potentiometers Resistance taper 15A 1B 3B 15C Slide Potentiometers Shaft Variety Unit:mm Detail dimensions R Metal Shaft L1 LB R1 12.5 5 7 15 5 7 17.5 5 7 20 7 12 25 7 12 Insulated Shaft Note Marked are specifications recommended by Alps Alpine. Knob Operating 9mm Size Metal Shaft Snap-in Type / Attached Parts Through Shaft Type The following parts are included with the product. Unit:mm Nut Ring Type 11 Washer 2 o14 0.5 o9.1 M9x0.75 308 Refer to P.309 for ordering products not listed.. 9mm Size Metal Shaft Snap-in Type / Ordering Products Not Listed When ordering product varieties that are not listed, specify referring to the examples below. Sample Part Number R K 0 9 L 1 1 4 0 F 1 5 C 0 B 1 0 3 Model type Model type Rotary Potentiometers Code Single-unit horizontal type Single-unit vertical type 122 Dual-unit horizontal type for tone 124 Dual-unit vertical type for tone 12B Dual-unit horizontal type for vol. 12D Dual-unit vertical type for vol. Slide Potentiometers 112 114 Shaft type Shaft type F Flat Metal Shaft Code Only available in flat format. Length of the shaft L1mm Length of the shaft Code Length of the shaft Code Length of the shaft 12 12.5 17 17.5 25 25 15 15 20 20 Insulated Shaft Code Knob Operating Detent Center detent C0 Without C1 With Through Shaft Type Code J 40 10 0 10 20 Term."1" Total resistance Code Total resistance k k 502 5 503 50 103 10 104 100 203 20 ) 1B ) 30 20 A) 15 A( 30 40 50 100 Output volt.across term.2-3 100 (%) Input volt. across term. 1-3 G 50 3B B: For tone & general (model type : 112, 114, 122, 124) V: For vol. (model type : 112, 114, 12B, 12D) 60 B( 15C l)( C tro 1B 70 on B 80 .c 3B ol V (v 15A 90 V A 100 G 100 (%) Resistance taper Output volt.across term.1-2 Code Input volt. across term. 1-3 Resistance taper 60 Rotation travel (%) 70 J 80 90 100 Term."3" 90 Ring Type Code J Resistance taper 80 70 60 50 40 30 C(1 5C 20 ) 10 100 90 Term."1" 80 70 60 50 40 30 Rotation travel (%) J 20 10 0 Term."3" Note Marked are specifications recommended by Alps Alpine. 309 Metal Shaft Potentiometers List of Varieties Type 9mm size RK09L Series Number of resistor elements 11mm size RK0972 RK119 Single-shaft RK0971 Dual-shaft Single-shaft Single/dual Dual Single Photo Terminal mounting Horizontal Vertical Horizontal Rotary Potentiometers Fixing method of bushing Screw Operating temperature range Guide -20 to 70 -40 to 85Vehicle-compatible -10 to 70 Slide Potentiometers Operating life Available for automotive use Vertical -40 to 85 15,000 cycles -- -- Life cycle (availability) Total resistance k 10, 20, 50, 100 10 Resistance taper 15A, 1B, 3B, 15C 1B Metal Shaft Rated Power 0.05W R10k 20 max. 10kR50k 30 max. 50kR Nominal total resistance of 0.1% or less Residual resistance Insulated Shaft Electrical performance Maximum attenuation Volume control 5kR 10k 10kR 50k 50kR Knob Operating Gang error applicable to Dual-unit parts for audio volume control purposes 100M min. 250V DC Through Shaft Type Voltage proof Without Without / With Detent Without Without, Center Ring Type Stopper strength 0.5Nm Push-pull strength 80N max. Without 0.5NmWith push-lock mechanism: 0.4N*m 0.5Nm 100N max. 10 to 55 to 10Hz/min., the amplitude is 1.5mm for all the frequencies, in the 3 direction of X, Y and Z and for 2 hours respectively Vibration Shaft style Inner-shaftflat type Outer-shaftslotted type Flat type Terminal style Page 300V AC for 1 minute or 360V for 2s 300V AC for 1minute Center-taps Attached switch -- -- -40dB to 0dB 3dB max. Insulation resistance Mechanical performance 5kR 10k 70dB min. 10kR 50k 80dB min. 50kR100k 90dB min. 100kR 100dB min. 70dB min. 80dB min. 90dB min. R10k 50 max. Insertion -- -- 306 Flat type Reflow Rotary switch Push-on push-off switch Push-on switch Push-lock switch 310 -- Push-on switch 321 Metal Shaft Potentiometers Soldering Conditions 343 Potentiometers Cautions 418 Potentiometers Measurement and Test Methods 420 Potentiometers Resistance Taper 422 Notes 1. For the switch attached, the single-shaft or inner shaft of the dual-shaft type can be chosen. 2. The operating temperature range for automotive applications can be raised upon request. Please contact us for details. 3. Indicates applicability to some products in the series. 304 Metal Shaft Potentiometers / Soldering Conditions Reference for Manual Soldering Series No. of solders RK09L, RK097 350 max. 3s max. 1 time RK203 300 max. 3s max. 1 time RK119 35010 +1 0 1 time RK271 350 max. RK501 35010 RK163 350 max. 5s max. 1 time Potentiometer terminal 300 max. 3s max. 1 time Motor terminal 350 max. 2s max. 1 time RK168 3 s 5s max. 1 time +1 0 1 time 5 s Slide Potentiometers Soldering time Rotary Potentiometers Tip temperature Reference for Dip Soldering Preheating Soldering surface Heating time temperature Series RK501 No. of solders 100 max. 2 min. max. 2605 51s 2 time max. 12010 2 min. max. 2605 51s 2 time Metal Shaft RK09L, RK097, RK203 Dip soldering Soldering Soldering time temperature Insulated Shaft Example of Reflow Soldering Condition Temperature profile A B 200 Through Shaft Type Temperature (C ) Knob Operating 300 C D 100 Ring Type Room temperature Time (s) Pre-heating E max. F max. G max. H max. Series RK119 A B C D E F G H No. of reflows 260 230 180 150 2 min. 3s 40s 4 min. 2 time max. Notes 1. When using an infrared reflow oven, solder may sometimes not be applied. Be sure to use a hot air reflow oven or at type that uses infrared rays in combination with hot air. 2. The temperatures given above are the maximum temperatures at the terminals of the potentiometer when employing a hot air reflow method. The temperature of the PC board and the surface temperature of the potentiometer may vary greatly depending on the PC board material, its size and thickness. Ensure that the surface temperature of the potentiometer does not rise to 250 or greater. 3. Conditions vary to some extent depending on the type of reflow bath used. Be sure to give due consideration to this prior to use. 343