315
1.04 Puller
2-arm pattern
The new model for the safe and fast removal of pulleys, wheels, ball
bearings, etc. Due to the bending-moment reinforcement on its
back face, the energy-saving design of the cross piece means even
stronger and safer pulling work. With the newly-developed
cantilever hook design, it is possible to use these higher forces
without losses over the whole width of the cross piece.
The high-speed adjustment feature supports the energy-saving
and fast operation. The spindle possesses an interchangeable tip,
meaning that a ball tip may also be employed if necessary.
Spindle may be
exchanged
for hydraulic
pressure spindle
(see table).
1.06 Universal puller
2-arm pattern
The reliable model for the fast and safe removal of pulleys, wheels,
ball bearings, etc.
Strong drop forged design.
Reversible hooks permit use as an internal or external puller.
Available extras are replaceable hooks for various
clamping reaches.
Spindle may be exchanged for hydraulic pressure spindle
(see table).
Code No. a1a2 min a2 max bAHydraulic spindle $c d e max. t 0
8000230 1.06/1 90 60 140 100 M 14x1,5 x 140 17 22 12 3,0 3,0 1.1
8000310 1.06/1A 130 70 180 100 M 14x1,5 x 140 17 22 12 3,0 3,0 1.3
8000580 1.06/2 160 80 220 150 G 1/2 x 210 1.06/HSP1 22 30 18 3,5 5,0 3.2
8000660 1.06/2A 200 90 260 150 G 1/2 x 210 1.06/HSP1 22 30 18 3,5 5,0 3.6
8000740 1.06/3 250 125 330 200 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 7.8
8000820 1.06/3A 350 125 420 200 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 9.2
8000900 1.06/4 520 185 600 200 G 1 x 310 1.06/HSP3 36 36 28 6,5 10,0 15.2
8112970 1.06/5 640 230 715 225 G 1 x 310 1.06/HSP3 36 50 33 10,0 18,0 23.5
Code No. a1a2 min a2 max bAHydraulic spindle $c d e max. t 0
1307703 1.04/1A 130 70 170 100 M 14x1,5 x 140 17 22 15 3,0 3,0 1.2
1307827 1.04/2A 200 110 260 150 G 1/2 x 210 1.06/HSP1 22 30 25 4,5 5,0 3.3
1307940 1.04/3A 350 150 420 200 G 3/4 x 280 1.06/HSP2 27 36 33 6,0 7,5 9.9
1.06 Universal puller
2-arm pattern, with extended hooks
As universal puller No. 1.06/1 to 1.06/4, but with extended
pulling hooks.
Spindle may be exchanged for hydraulic pressure spindle
(see table).
Code No. a1a2 min a2 max bAHydraulic spindle $c d e max. t 0
8108350 1.06/1-2 90 60 140 200 M 14x1,5 x 140 17 22 12 3,0 3,0 1.5
8108430 1.06/1A-2 130 70 180 200 M 14x1,5 x 140 17 22 12 3,0 3,0 1.8
8108510 1.06/2-3 160 80 220 300 G 1/2 x 210 1.06/HSP1 22 30 18 3,5 5,0 4.4
8108780 1.06/2A-3 200 90 260 300 G 1/2 x 210 1.06/HSP1 22 30 18 3,5 5,0 4.8
8001200 1.06/3-3 250 125 330 300 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 9.1
8108860 1.06/3A-3 350 125 420 300 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 10.5
8108940 1.06/4-3 520 185 600 300 G 1 x 310 1.06/HSP3 36 36 28 6,5 10,0 16.5
8109080 1.06/3-4 250 125 330 400 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 10.4
8109160 1.06/3A-4 350 125 420 400 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 11.8
8109240 1.06/4-4 520 185 600 400 G 1 x 310 1.06/HSP3 36 36 28 6,5 10,0 17.8
8109320 1.06/3-5 250 125 330 500 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 11.6
8112380 1.06/3A-5 350 125 420 500 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 13.0
8112460 1.06/4-5 520 185 600 500 G 1 x 310 1.06/HSP3 36 36 28 6,5 10,0 19.0
Baldur_9_GB.mif Seite 315 Freitag, 18. Juli 2003 10:15 10
316
1.06 Universal puller
2-arm pattern, with rigid hooks
Design as universal puller No. 1.06/1 to 1.06/4, but with rigid
pulling hooks. For greater ease in setting the clamping spread.
The hooks clamp automically when under tension.
The hooks may be reversed to convert the puller from an external
one to an internal one. Spindle may be exchanged for hydraulic
pressure spindle (see table).
Code No. a1a2 min a2 max bAHydraulic spindle $c d e max. t 0
8001470 1.06/11 100 50 140 100 M 14x1,5 x 140 17 22 15 4,0 3,0 0.8
8001040 1.06/1A1 140 60 180 100 M 14x1,5 x 140 17 22 15 4,0 3,0 1.2
8001550 1.06/21 170 80 220 150 G 1/2 x 210 1.06/HSP1 22 30 24 3,5 5,0 2.7
8001120 1.06/2A1 210 90 260 150 G 1/2 x 210 1.06/HSP1 22 30 24 3,5 5,0 3.1
8001630 1.06/31 250 125 340 200 G 3/4 x 280 1.06/HSP2 27 36 32 5,0 7,5 6.6
8001390 1.06/3A1 340 125 430 200 G 3/4 x 280 1.06/HSP2 27 36 32 5,0 7,5 8.0
8109400 1.06/41 520 185 610 200 G 1 x 310 1.06/HSP3 36 36 32 5,0 10,0 14.0
1.06 Fast clamping puller
2-arm pattern, with fast-clamp adjustment
The tried and tested model for the safe and fast removal
of pulleys, wheels, ball bearings, etc.
Strong drop forged pattern.
By reversing the hooks, this tool may be used as an
internal or external puller. Exchangeable hooks for several
clamping reaches available as accessories.
With the innovative high-speed clamps, fast and uncomplicated
setting-up and readjustment is child's play.
Spindle may be exchanged for hydraulic pressure spindle
(see table).
Code No. a1a2 min a2 max bAHydraulic spindle $c d e max. t 0
1213830 1.06/1-E 90 60 140 100 M 14x1,5 x 140 17 22 12 3,0 3,0 1.1
1215140 1.06/1A-E 130 70 180 100 M 14x1,5 x 140 17 22 12 3,0 3,0 1.3
1216570 1.06/2-E 160 80 220 150 G 1/2 x 210 1.06/HSP1 22 30 18 3,5 5,0 3.2
1217720 1.06/2A-E 200 90 260 150 G 1/2 x 210 1.06/HSP1 22 30 18 3,5 5,0 3.6
1218980 1.06/3-E 250 125 330 200 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 7.8
1220160 1.06/3A-E 350 125 420 200 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 9.2
1.06 Universal puller
2-arm pattern, with slim hooks
The feet of the hooks are very slim and particularly suitable for
barely-accessible places.
Code No. a b A$c d e f max. t 0
8113510 1.06/S1 100 100 M 14x1,5 x 140 17 27 6 3,6 13 2,5 1.0
8113780 1.06/S1A 140 100 M 14x1,5 x 140 17 27 6 3,6 13 2,5 1.2
8114830 1.06/S2 160 150 G 1/2 x 210 22 40 8 5,0 17 5,0 3.0
8114910 1.06/S2A 200 150 G 1/2 x 210 22 40 8 5,0 17 5,0 3.2
Baldur_9_GB.mif Seite 316 Freitag, 18. Juli 2003 10:15 10
317
Code No. a1a2bSpindle c d e max. t 0
8005700 1.06/2-3-HSP1 160 220 225 1.06/HSP1 30 18 3,5 5,0 4.8
8005890 1.06/2A-3-HSP1 200 260 225 1.06/HSP1 30 18 3,5 5,0 5.2
8005970 1.06/3-3-HSP2 250 330 225 1.06/HSP2 36 28 6,5 7,5 9.5
8006940 1.06/3A-3-HSP2 350 420 225 1.06/HSP2 36 28 6,5 7,5 11.4
8007240 1.06/4-3-HSP3 520 600 190 1.06/HSP3 36 28 6,5 10,0 18.4
8007670 1.06/3-4-HSP2 250 330 325 1.06/HSP2 36 28 6,5 7,5 10.4
8007750 1.06/3A-4-HSP2 350 420 325 1.06/HSP2 36 28 6,5 7,5 11.3
8007830 1.06/4-4-HSP3 520 600 290 1.06/HSP3 36 28 6,5 10,0 19.4
8007910 1.06/3-5-HSP2 250 330 425 1.06/HSP2 36 28 6,5 7,5 12.4
8008480 1.06/3A-5-HSP2 350 420 425 1.06/HSP2 36 28 6,5 7,5 13.4
8008560 1.06/4-5-HSP3 520 600 390 1.06/HSP3 36 28 6,5 10,0 20.4
1.06 HSP Universal puller
hydraulic, 2-arm pattern, with extended hooks
For the highest requirements.
With the hydraulic spindle, a controlled and safe pulling
action is possible at all times.
1.06 HSP Universal puller
hydraulic, 2-arm pattern, with rigid hooks
With pulling hooks in one piece, drop forged pattern.
By reversing the hooks, this tool may be used as an
internal or external puller.
With the hydraulic spindle, a controlled and safe pulling
action is possible at all times.
Code No. a1a2bSpindle c d e max. t 0
8008640 1.06/21-HSP1 170 220 75 1.06/HSP1 30 24 3,5 5,0 3.7
8008720 1.06/2A1-HSP1 210 260 75 1.06/HSP1 30 24 3,5 5,0 3.8
8008800 1.06/31-HSP2 250 340 115 1.06/HSP2 36 32 5,0 7,5 7.0
8008990 1.06/3A1-HSP2 340 430 115 1.06/HSP2 36 32 5,0 7,5 8.8
8009370 1.06/41-HSP3 520 610 80 1.06/HSP3 36 32 5,0 10,0 14.8
1.06 HSP Universal puller
hydraulic, 2-arm pattern
The tried and tested model for the safe and fast removal of pulleys,
wheels, ball bearings, etc. Drop forged pattern.
By reversing the hooks, this tool may be used as an internal or
external puller. With the hydraulic spindle, a controlled and safe
pulling action is possible at all times.
Code No. a1a2bSpindle c d e max. t 0
8000150 1.06/2-HSP1 160 220 75 1.06/HSP1 30 18 3,5 5,0 3.6
8002870 1.06/2A-HSP1 200 260 75 1.06/HSP1 30 18 3,5 5,0 4.0
8003170 1.06/3-HSP2 250 330 125 1.06/HSP2 36 28 6,5 7,5 8.2
8003920 1.06/3A-HSP2 350 420 125 1.06/HSP2 36 28 6,5 7,5 9.6
8004060 1.06/4-HSP3 520 600 90 1.06/HSP3 36 28 6,5 10,0 16.5
8004730 1.06/5-HSP3 640 715 110 1.06/HSP3 50 33 10,0 18,0 24.5
Baldur_9_GB.mif Seite 317 Freitag, 18. Juli 2003 10:15 10
318
1.06 HSP Hydraulic pressure spindle
These grease-hydraulic pressure spindle has been designed for
controlled and safe pulling work, and is set up for a pressure of
up to 15 t.
Preparation for use:
1. Before using, check whether the pressure spindle is screwed far
enough out of the cap, so that the pressure pad is in the initial
position in the hydraulic cylinder.
2. Unscrew the cap from the spindle body.
For this purpose, first slacken off the grup screw.
3. Screw the spindle body from beneath into the cross piece
of the puller until the body protrudes approx. 60 mm
from the cross piece.
4. Screw the cap onto the spindle body until the stop, and
then fix it in position by turning in the grub screw.
Use and operation: e.g. HSP3
5. Place the puller into position and pre-tension the spindle
body using a size 41 mm wrench.
6. Screw the pressure spindle size 17 mm into the cap.
The hydraulic effect will come into use. The stroke of the
pressure pad in the hydraulic cylinder is max. 12 mm.
The workpiece that has been loosened by the hydraulic force
may be pulled off completely by turning the spindle body
with the cap size 41 mm.
7. Following its use, the pressure spindle (size 17 mm) is
turned back into its initial position and the pressure pad
pushed into the hydraulic cylinder.
Code No. a b c d e f Stroke mm max. t 0
8116100 1.06/HSP1 1/2" 55 135 350 12 32 12 12 1.1
8116290 1.06/HSP2 3/4" 80 205 420 12 36 12 12 1.8
8116370 1.06/HSP3 1" 125 165 465 17 41 12 15 3.6
Code No. a1a2bSpindle c d e max. t 0
1221256 1.06/2-E-HSP1 160 220 75 1.06/HSP1 30 18 3,5 5,0 3.7
1221450 1.06/2A-E-HSP1 200 260 75 1.06/HSP1 30 18 3,5 5,0 4.1
1221639 1.06/3-E-HSP2 250 330 125 1.06/HSP2 36 28 6,5 7,5 7.6
1221760 1.06/3A-E-HSP2 350 420 125 1.06/HSP2 36 28 6,5 7,5 8.8
1.06 Extension for pullers
DGBM
The one-piece drop forged extensions enable the clamping reach
to be extended indefinitely. The extensions may be used together
with all hooks of the 1.06 range. (Delivery in pairs).
DGBM = German Federal Utility Patent
Code No. Bb0
8036500 1.06/V100 for 1.06/A and 1.06/100 100 0.4
8036690 1.06/V150 for 1.06/B and 1.06/150 150 1.2
8036770 1.06/V200 for 1.06/C and 1.06/200 200 2.6
1.06 HSP Fast clamping puller
hydraulic, 2-arm pattern
With the hydraulic spindle, a controlled and safe pulling
action is possible at all times.
With the innovative high-speed clamps, fast and uncomplicated
setting-up and readjustment is child's play.
Baldur_9_GB.mif Seite 318 Freitag, 18. Juli 2003 10:15 10
319
1.06 Pulling hooks
set of 2 pieces
Pulling hooks (1 pair including clamping parts),
in standard and special lengths.
Code No. Bb c d e 0
8035020 1.06/A 1.06/1 /1A 100 22 12 3,0 0.6
8035100 1.06/B 1.06/2 /2A 150 30 18 3,5 1.6
8035290 1.06/C 1.06/3 /3A /4 200 36 28 6,5 3.5
8114400 1.06/D 1.06/5 225 50 35 11,0 3.5
8035370 1.06/AV 1.06/1 /1A 200 22 12 3,0 1.1
8035450 1.06/BV 1.06/2 /2A 300 30 18 3,5 2.8
8035530 1.06/CV 1.06/3 /3A /4 300 36 28 6,5 5.0
8035610 1.06/DV 1.06/3 /3A /4 400 36 28 6,5 6.3
8035880 1.06/EV 1.06/3 /3A /4 500 36 28 6,5 7.5
8112700 1.06/D-300 1.06/5 320 50 35 11,0 5.7
8112890 1.06/D-400 1.06/5 420 50 35 11,0 6.4
8113860 1.06/D-500 1.06/5 520 50 35 11,0 8.4
1.06 Pulling hooks
set of 2 pieces, rigid pattern
Code No. Bb c d e 0
8036260 1.06/100 1.06/11 1.06/1A1 100 22 15 3,0 0.4
8111490 1.06/150 1.06/21 1.06/2A1 150 30 24 3,5 1.1
8036420 1.06/200 1.06/31 1.06/3A1 1.06/41 200 36 32 5,0 2.4
1.06 Pulling hooks
set of 2 pieces, slim pattern
The forged hook feet are very shallow and thus particularly
suitable for barely-accessible places.
Code No. Bb c d e f 0
1175513 1.06/S100 1.06/S1 1.06/S1A 100 27 6 3,6 13 0.5
1175548 1.06/S200 1.06/S1 1.06/S1A 200 27 6 3,6 13 1.0
1175556 1.06/S250 1.06/S1 1.06/S1A 250 27 6 3,6 13 1.2
1554840 1.06/S100S 1.06/S1 1.06/S1A 100 27 6 2,3 13 0.5
1554859 1.06/S200S 1.06/S1 1.06/S1A 200 27 6 2,3 13 1.0
1554867 1.06/S250S 1.06/S1 1.06/S1A 250 27 6 2,3 13 1.2
1175564 1.06/S150 1.06/S2 1.06/S2A 150 40 8 5,0 17 1.3
1175572 1.06/S220 1.06/S2 1.06/S2A 220 40 8 5,0 17 1.7
1175580 1.06/S300 1.06/S2 1.06/S2A 300 40 8 5,0 17 2.2
1.06 Fast clamping pulling hooks
set of 2 pieces
With the innovative high-speed clamps, fast and uncomplicated
setting-up and readjustment is child's play.
Code No. Bb c d e 0
1221213 1.06/A-E 1.06/1-E 1.06/1A-E 100 22 12 3,0 0.6
1221221 1.06/B-E 1.06/2-E 1.06/2A-E 150 30 18 3,5 1,6
1221248 1.06/C-E 1.06/3-E 1.06/3A-E 200 36 28 6,5 3.5
Baldur_9_GB.mif Seite 319 Freitag, 18. Juli 2003 10:15 10
320
1.06 AS Puller set
2-arm pattern with 6 slim hooks
With very slim forged hooks, thus particularly suitable for
barely-accessible places.
Code No. Contents 2 each 0
8001710 1.06/AS 1.06/S100 S200 S250 3.3
1.06 Puller set
with display stand
Code No. B0
8111570 1.06/ST 1.06/1 /1A /2 /2A /3 17.5
8111650 1.06/ST1 1.06/11 /1A1 /21 /2A1 /31 15.0
1322745 1.06/ST-E 1.06/1-E /1A-E /2-E /2A-E /3-E 20.0
1.07 Universal puller
3-arm pattern
For use as internal or external puller.
The even load distribution on the three pulling hooks guarantees
secure grip and central pulling.
Hooks in special lengths available.
Hooks 1.07/AV (clamping reach 200 mm) for 1.07/1 and 1.07/1A,
and hooks 1.07/BV (clamping reach 300 mm) for 1.07/2 and
1.07/2A. Spindle may be exchanged for hydraulic pressure
spindle (see table).
Code No. a1a2 min a2 max bAHydraulic spindle $c d e max. t 0
8113940 1.07/1 90 70 140 100 M 14x1,5 x 140 17 22 12 3,0 3,0 1.4
8114080 1.07/1A 130 80 180 100 M 14x1,5 x 140 17 22 12 3,0 3,0 1.6
8114160 1.07/2 160 100 220 150 G 1/2 x 210 1.06/HSP1 22 30 18 3,5 5,0 3.6
8114240 1.07/2A 200 100 260 150 G 1/2 x 210 1.06/HSP1 22 30 18 3,5 5,0 4.0
1541757 1.07/3 250 100 400 200 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 9.0
Baldur_9_GB.mif Seite 320 Freitag, 18. Juli 2003 10:15 10
321
1.07 Universal puller
3-arm pattern, with slim hooks
The feet of the hooks are very slim and particularly suitable
for barely-accessible places.
Code No. a b A$c d e f max. t 0
8116450 1.07/S1 90 100 M 14x1,5 x 140 17 27 6 3,6 13 2,5 1.3
8116530 1.07/S1A 130 100 M 14x1,5 x 140 17 27 6 3,6 13 2,5 1.4
8116610 1.07/S2 160 150 G 1/2 x 210 22 40 8 5,0 17 5,0 3.6
8116880 1.07/S2A 200 150 G 1/2 x 210 22 40 8 5,0 17 5,0 4.0
1.07 Universal puller
3-arm pattern, with rigid hooks
Design as universal puller No. 1.07/1 to 1.07/3, but with rigid
pulling hooks. For greater ease in setting the clamping spread.
The hooks clamp automatically when under tension.
The hooks may be reversed to convert the puller from an external
one to an internal one. Spindle may be exchanged for hydraulic
pressure spindle (see table).
Code No. a1a2 min a2 max bAHydraulic spindle $c d e max. t 0
1305549 1.07/11 90 70 140 100 M 14x1,5 x 140 17 22 15 4,0 3,0 1.3
1306022 1.07/1A1 130 80 180 100 M 14x1,5 x 140 17 22 15 4,0 3,0 1.5
1306154 1.07/21 160 100 220 150 G 1/2 x 210 1.06/HSP1 22 30 24 3,5 5,0 3.0
1306278 1.07/2A1 200 100 260 150 G 1/2 x 210 1.06/HSP1 22 30 24 3,5 5,0 3.2
1554778 1.07/31 250 100 400 200 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 9.0
1.07/4 Universal puller
3-arm pattern
Just like our standard model No. 1.06, this puller is designed
for all branches of industry, but particularly for the construction
of electric motors. It is also suitable for removing heavy, multistage
pulley wheels, flywheels, gear wheels, etc.
Pins are used to lock the arms at 120° to each other on the hub.
The clamping reach may be extended to 490 mm by using
extensions No. 1.07/CV, 1.07/DV and 1.07/EV. Spindle may be
exchanged for hydraulic pressure spindle (see table).
This puller may also be used with the hydraulic aid 1.50
without requiring any reduction bushing.
Code No. a1a2bAHydraulic spindle $c d e max. t 0
8002440 1.07/4 450 530 200 G 1 x 360 1.06/HSP3 36 36 28 6,5 10 19.0
Baldur_9_GB.mif Seite 321 Freitag, 18. Juli 2003 10:15 10
322
1.07 HSP Universal puller
hydraulic, 3-arm pattern
The tried and tested model for the removal of pulleys, wheels,
ball bearings, etc. Drop forged pattern.
By reversing the hooks, this tool may be used as an internal
or external puller. With the hydraulic spindle, a controlled
and safe pulling action is possible at all times.
Code No. a1a2bSpindle c d e max. t 0
8009960 1.07/2-HSP1 160 220 75 1.06/HSP1 30 18 3,5 5,0 4.4
8010970 1.07/2A-HSP1 200 260 75 1.06/HSP1 30 18 3,5 5,0 4.8
1554816 1.07/3-HSP2 250 100 80 1.06/HSP2 36 28 6,5 7,5 9.3
8012400 1.07/4-HSP3 450 530 80 1.06/HSP3 36 28 6,5 10,0 19.4
1.07 HSP Fast clamping puller
hydraulic, 3-arm pattern
With the hydraulic spindle, a controlled and safe pulling action
is possible at all times. With the innovative high-speed clamps,
fast and uncomplicated setting-up and readjustment is child's play.
Code No. a1a2bSpindle c d e max. t 0
1221922 1.07/2-E-HSP1 160 220 75 1.06/HSP1 30 18 3,5 5,0 4.5
1222554 1.07/2A-E-HSP1 200 260 75 1.06/HSP1 30 18 3,5 5,0 4.7
1554824 1.07/3-E-HSP2 250 400 80 1.06/HSP2 36 28 6,5 7,5 9.3
1.07 Fast clamping puller
3-arm pattern, with fast-clamp adjustment
May be used as an internal or external puller.
The even distribution of the loading over the three hooks results
in secure grip and centered pulling action.
With the innovative high-speed clamps, fast and uncomplicated
setting-up and readjustment is child's play. Spindle may be
exchanged for hydraulic pressure spindle (see table).
Code No. a1a2 min a2 max bAHydraulic spindle $c d e max. t 0
1222902 1.07/1-E 90 70 140 100 M 14x1,5 x 140 17 22 12 3,0 3,0 1.4
1225901 1.07/1A-E 130 80 180 100 M 14x1,5 x 140 17 22 12 3,0 3,0 1.6
1227335 1.07/2-E 160 100 220 150 G 1/2 x 210 1.06/HSP1 22 30 18 3,5 5,0 3.6
1227459 1.07/2A-E 200 100 260 150 G 1/2 x 210 1.06/HSP1 22 30 18 3,5 5,0 4.0
1554751 1.07/3-E 250 100 400 200 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 9.0
Baldur_9_GB.mif Seite 322 Freitag, 18. Juli 2003 10:15 10
323
1.07 Extension for pullers
set of 3 pieces
The one-piece drop forged extensions enable the clamping
reach to be extended. The extensions may be used together
with all hooks of the 1.07 range.
Code No. Bb0
1307576 1.07/V100 for 1.07/A and 1.07/100 100 0.4
1307584 1.07/V150 for 1.07/B and 1.07/150 150 1.6
1307592 1.07/V200 for 1.07/C and 1.07/200 200 2.6
1.07 Pulling hooks
set of 3 pieces
Code No. Bb c d e 0
1307401 1.07/A 1.07/1 1.07/1A 100 22 12 3,0 0.9
1307428 1.07/B 1.07/2 1.07/2A 150 30 118 3,5 2.4
1307436 1.07/C 1.07/3 1.07/4 200 36 28 6,5 5.2
1307452 1.07/A-E 1.07/1 1.07/1A 100 22 12 3,0 0.9
1307460 1.07/B-E 1.07/2 1.07/2A 150 30 18 3,5 0.9
1307479 1.07/C-E 1.07/3 1.07/4 200 36 28 6,5 8.0
1307487 1.07/AV 1.07/1 1.07/1A 200 22 12 3,0 1.6
1307495 1.07/BV 1.07/2 1.07/2A 300 30 18 3,5 4.2
1307509 1.07/CV 1.07/3 1.07/4 300 36 28 6,5 7.5
1307517 1.07/DV 1.07/3 1.07/4 400 36 28 6,5 9.4
1307525 1.07/EV 1.07/3 1.07/4 500 36 28 6,5 11.2
1.07 Pulling hooks
set of 3 pieces, rigid pattern
for 3-arm pullers.
Code No. Bb c d e 0
1307533 1.07/100 1.07/11 1.07/1A1 100 22 15 3,0 0.6
1307541 1.07/150 1.07/21 1.07/2A1 150 30 24 3,5 1.6
1307568 1.07/200 1.07/3 1.07/4 200 36 32 5,0 3.7
1.07 Pulling hooks
set of 3 pieces, slim pattern
The feet of the hooks are very slim and thus particularly
suitable for barely-accessible places.
Code No. Bb c d e f 0
1307606 1.07/S100 1.07/S1 1.07/S1A 100 27 6 3,6 13 1.2
1307622 1.07/S200 1.07/S1 1.07/S1A 200 27 6 3,6 13 2.4
1307630 1.07/S250 1.07/S1 1.07/S1A 250 27 6 3,6 13 3.0
1554786 1.07/S100S 1.07/S1 1.07/S1A 100 27 6 2,3 13 0.8
1554794 1.07/S200S 1.07/S1 1.07/S1A 200 27 6 2,3 13 1.6
1554808 1.07/S250S 1.07/S1 1.07/S1A 250 27 6 2,3 13 2.0
1307649 1.07/S150 1.07/S2 1.07/S2A 150 40 8 5,0 17 2.7
1307657 1.07/S220 1.07/S2 1.07/S2A 220 40 8 5,0 17 3.4
1307665 1.07/S300 1.07/S2 1.07/S2A 300 40 8 5,0 17 5.0
1.07/A-E
1.07/AV
1.07/A
Baldur_9_GB.mif Seite 323 Freitag, 18. Juli 2003 10:15 10
324
1.07/KSE Puller set
Contents: case, spindle, 1 cross piece each 2-arm and 3-arm
pattern and 3 puller hooks length 100 mm.
Code No. 0
1438484 1.07/K-1-SE 2.1
1.07 AS Puller set
3-arm pattern with 9 slim hooks
The feet of the hooks are very slim and thus particularly
suitable for barely-accessible places.
Code No. Contents 3 each 0
8117260 1.07/AS 1.07/S100 S200 S250 4.3
1.07 K Puller set
with 9 hooks, in plastic case
Contents: case, spindle, 1 cross piece each 2-arm and 3-arm
pattern and 9 puller hooks in length 100, 200, 250 mm.
Code No. amax b1b2b3A$c d e 0
8117340 1.07/K 120 100 200 250 M 14x1,5 x 140 17 27 6 3,6 5.0
1.07 Puller set
in plastic case
With three quick-clamping hooks and hydraulic spindle.
Suitable for internal and external pulling work, 2-arm or 3-arm,
with powerful hydraulic spindle and quick-clamping hooks.
The right puller for the job - and ready in a second.
The best equipment for the professional for everyday heavy duty
work. For industrial or car and truck repairs - set of two.
Your price advantage: 1 spindle and 2 hooks saved.
Hydraulic spindle HSP1 (max. 12 t force).
Three quick-clamping hooks for internal and external use.
Heavy duty cross pieces for 2-arm or 3-arm use.
And everything stored safely in a handy case.
Contents: case, spindle, 1 cross piece each 2-arm and 3-arm,
3 puller hooks.
Code No. a1a2bA$c d e 0
1438492 1.07/K-2-E-HSP1 160 220 75 1.06/HSP1 30 18 3 5 2.1
Baldur_9_GB.mif Seite 324 Freitag, 18. Juli 2003 10:15 10
325
1.11 Puller
3-arm pattern
The reliable, heavy-duty model for the removal of pulleys,
wheels, ball bearings, etc. The double hook ends, wide or
narrow, grip automatically.
The wide hook ends of the puller 1.10/2 and 1.11/2 possess
8 mm slots, so that pulleys or gears may also be pulled off using
8 mm bolts.
Code No. amax bA$c1c2d e max. t 0
8002950 1.11/1 90 80 M 14x1,5 x 125 17 17 10 7 2 3,0 0.9
8003090 1.11/2 160 130 M 18x1,5 x 170 19 24 20 13 3 7,5 2.7
1.10 Puller
2-arm pattern
The reliable, heavy duty model for the removal of pulleys,
wheels, ball bearings, etc.
The double hook ends, wide or narrow, grip automatically.
The wide hook ends of the puller 1.10/2 and 1.11/2 possess
8 mm slots, so that pulleys or gears may also be pulled off using
8 mm bolts.
Code No. amax bA$c1c2d e max. t 0
8002600 1.10/1 90 80 M 14x1,5 x 125 17 17 10 7 2 2 0.7
8002790 1.10/2 160 130 M 18x1,5 x 170 19 24 20 13 3 5 2.0
1.08 Universal puller
2-arm pattern, with fast spindle adjustment
Twice as fast and twice as simple.
With the fast spindle adjustment feature, the spindle can be
set the desired range in a moment.
When the clamping yoke is released, the 4-part internal thread
closes, and takes the full working pressure.
Code No. a1a2 min a2 max bA$c d e max. t 0
8019090 1.08/1A 130 80 180 100 M 14x1,5 x 140 17 22 12 3,0 3,0 1.4
8000070 1.08/2A 200 110 260 150 G 1/2 x 210 22 30 18 3,5 5,0 3.8
8018950 1.08/3A 350 130 420 200 G 3/4 x 280 27 36 28 6,5 7,5 10.2
Baldur_9_GB.mif Seite 325 Freitag, 18. Juli 2003 10:15 10
326
1.13 Puller
3-arm pattern
Handy robust model for the removal of pulleys, wheels,
ball bearings, etc. Inexpensive economy model.
The hook tips grip automatically.
Code No. amax bA$c d e max. t 0
8004140 1.13/0 70 80 M 12x1,5 x 110 14 14 8 2,0 1,5 0.5
8004220 1.13/1 90 120 M 14x1,5 x 155 17 18 11 2,5 3,0 1.0
8004300 1.13/2 130 160 M 18x1,5 x 200 19 25 14 3,0 7,5 2.6
8004490 1.13/3 180 200 G 1/2 x 250 22 32 20 3,5 12,0 5.1
1.12 Battery-terminal puller
2-arm pattern
The perfect tool for removing small parts such as battery terminals,
pulleys, wheels, ball bearings, etc. The hook tips grip automatically.
Code No. amax bAc d e max. t /
8003760 1.12/01 60 60 M 10x1,5 x 80 10 5 2 0,5 160
8003840 1.12/02 60 40 M 10x1,5 x 60 10 5 2 0,5 120
1.12 Puller
2-arm pattern
Handy robust model for the removal of pulleys, wheels,
ball bearings, etc. Inexpensive economy model.
The hook tips grip automatically.
Code No. amax bA$c d e max. t 0
8003250 1.12/0 70 80 M 12x1,5 x 110 14 14 8 2,0 1 0.4
8003330 1.12/1 90 120 M 14x1,5 x 155 17 18 11 2,5 2 0.7
8003410 1.12/2 130 160 M 18x1,5 x 200 19 25 14 3,0 5 1.9
8003680 1.12/3 180 200 G 1/2 x 250 22 32 20 3,5 8 3.7
Baldur_9_GB.mif Seite 326 Freitag, 18. Juli 2003 10:15 10
327
1.13 Battery-terminal puller
3-arm pattern
The perfect tool for removing small parts such as battery terminals,
pulleys, wheels, ball bearings, etc. The hook tips grip automatically.
Code No. amax bAc d e max. t /
8004570 1.13/01 60 60 M 10x1,5 x 80 10 5 2 0,75 200
8004650 1.13/02 60 40 M 10x1,5 x 60 10 5 2 0,75 150
1.14 HSP Puller
hydraulic, 2-arm pattern
The reliable, extra-strong model for the removal of pulleys,
wheels, ball bearings, etc. With technical and economical
benefits due to the variable clamping reach and automatic
grip of the hooks. Especially suited to removing V-belt pulley
wheels and flywheels mounted on longer shafts.
With the hydraulic spindle, a controlled and safe pulling
action is possible at all times.
Code No. amax bA$c d e max. t 0
1392883 1.14/3-HSP1 250 260 1.06/HSP1 22 32 18 3,5 8 4.3
1392913 1.14/4-HSP1 280 390 1.06/HSP1 22 32 20 3,5 8 5.1
1.14 Puller
2-arm pattern
The reliable, extra-strong model for the removal of pulleys,
wheels, ball bearings, etc. With technical and economical
benefits due to the variable clamping reach and automatic
grip of the hooks. Especially suited to removing V-belt pulley
wheels and flywheels mounted on longer shafts. Spindle may
be exchanged for hydraulic pressure spindle (see table).
Code No. amax bAHydraulic spindle $c d e max. t /
8004810 1.14/0 90 100 M 12x1,5 x 110 14 14 9 2,0 1 500
8005030 1.14/1 130 140 M 14x1,5 x 140 17 18 11 2,0 2 800
8005380 1.14/2 200 210 M 18x1,5 x 200 19 25 16 3,0 5 2100
8005460 1.14/3 250 260 G 1/2 x 250 1.06/HSP1 24 32 18 3,5 8 4300
8005540 1.14/4 280 390 G 1/2 x 250 1.06/HSP1 24 32 20 3,5 8 5100
8005620 1.14/5 420 480 G 1/2 x 350 1.06/HSP1 24 32 20 3,5 8 5800
Baldur_9_GB.mif Seite 327 Freitag, 18. Juli 2003 10:15 10
328
1.15 HSP Puller
hydraulic, 3-arm pattern
The reliable, extra-strong model for the removal of pulleys,
wheels, ball bearings, etc. With technical and economical
benefits due to the variable clamping reach and automatic
grip of the hooks. Especially suited to removing V-belt pulley
wheels and flywheels mounted on longer shafts.
With the hydraulic spindle, a controlled and safe pulling
action is possible at all times.
Code No. amax bA$c d e max. t 0
1392956 1.15/3-HSP1 250 260 1.06/HSP1 22 32 18 3,5 12 6.1
1392980 1.15/4-HSP1 280 390 1.06/HSP1 22 32 20 3,5 12 7.1
1.14 L Fan puller
2-arm pattern
The especially-slender hooks reach through the slots the collar
of the fan. Due to their slender hooks and the three adjustment
positions of its clamping reach, these pullers are also particularly
suitable for the dismantling of gear arrangements.
Hooks grip automatically.
Code No. amax bA$c d e max. t 0
8005110 1.14/1L 150 200 M 14x1,5 x 155 17 10 6 2 2 0.9
1.15 Puller
3-arm pattern
The reliable, extra-strong model for the removal of pulleys,
wheels, ball bearings, etc. With technical and economical
benefits due to the variable clamping reach and automatic
grip of the hooks. Especially suited to removing V-belt pulley
wheels and flywheels mounted on longer shafts. Spindle may
be exchanged for hydraulic pressure spindle (see table).
Code No. amax bAHydraulic spindle $c d e max. t /
8006000 1.15/0 90 100 M 12x1,5 x 110 14 14 9 2,0 2 650
8006190 1.15/1 130 140 M 14x1,5 x 140 17 18 11 2,0 3 1100
8006350 1.15/2 200 210 M 18x1,5 x 200 19 25 16 3,0 8 2900
8006430 1.15/3 250 260 G 1/2 x 250 1.06/HSP1 24 32 18 3,5 12 6100
8006510 1.15/4 280 390 G 1/2 x 250 1.06/HSP1 24 32 20 3,5 12 7100
8006780 1.15/5 420 480 G 1/2 x 350 1.06/HSP1 24 32 20 3,5 12 8200
Baldur_9_GB.mif Seite 328 Freitag, 18. Juli 2003 10:15 10
329
1.16 Puller
2-arm pattern
Very strong type. Especially suitable for industrial purposes and
for heavy agricultural and construction machines.
Hooks grip automatically. Spindle may be exchanged for
hydraulic pressure spindle (see table).
Code No. amax bAHydraulic spindle $c d e max. t 0
8007080 1.16/1 280 300 G 1 x 360 1.06/HSP3 36 32 19 3 8 8.0
8007160 1.16/2 420 420 G 1 x 500 1.06/HSP3 36 32 22 3 8 10
1.15 L Fan puller
3-arm pattern
The especially-slender hooks reach through the slots the collar of
the fan. Due to their slender hooks and the three adjustment
positions of its clamping reach, these pullers are also particularly
suitable for the dismantling of gear arrangements.
Hooks grip automatically.
Code No. amax bA$c d e max. t 0
8006270 1.15/1L 150 200 M 14x1,5 x 155 17 10 6 2 3 1.3
1.16 HSP Puller
hydraulic, 2-arm pattern
Very strong type. Especially suitable for industrial purposes
and for heavy agricultural and construction machines.
Hooks grip automatically. With the hydraulic spindle,
a controlled and safe pulling action is possible at all times.
Code No. amax bA$c d e max. t 0
8012590 1.16/1-HSP3 280 190 1.06/HSP3 36 32 19 3 8 9.3
8012670 1.16/2-HSP3 420 310 1.06/HSP3 36 32 22 3 8 11.3
Baldur_9_GB.mif Seite 329 Freitag, 18. Juli 2003 10:15 10
330
1.17 Puller
3-arm pattern
Very strong type. Especially suitable for industrial purposes
and for heavy agricultural and construction machines.
Hooks grip automatically. Spindle may be exchanged for
hydraulic pressure spindle (see table).
Code No. amax bAHydraulic spindle $c d e max. t 0
8007320 1.17/1 300 300 G 1 x 360 1.06/HSP3 36 32 19 312 9.7
8007400 1.17/2 425 425 G 1 x 500 1.06/HSP3 36 32 22 312 13.2
1.17 HSP Puller
hydraulic, 3-arm pattern
Very strong type. Especially suitable for industrial purposes
and for heavy agricultural and construction machines.
Hooks grip automatically. With the hydraulic spindle,
a controlled and safe pulling action is possible at all times.
Code No. amax bA$c d e max. t 0
8014290 1.17/1-HSP3 300 190 1.06/HSP3 36 32 19 3 12 11
8014370 1.17/2-HSP3 425 315 1.06/HSP3 36 32 22 3 12 14.5
1.18 Puller ECO
2-arm pattern
The tried and tested range for economical bearing removal.
Code No. amax bA$c d e max. t 0
1464965 1.18/1 110 110 M 14x1,5 x 163 17 17 18 5,0 2 1.0
1464973 1.18/2 160 140 M 18x1,5 x 215 19 21 20 6,5 3 1.9
1464981 1.18/3 200 200 G 1/2 x 282 22 22 22 7,5 5 2.3
Baldur_9_GB.mif Seite 330 Freitag, 18. Juli 2003 10:15 10
331
1.19 Puller ECO
3-arm pattern
The tried and tested range for economical bearing removal.
Code No. amax bA$c d e max. t 0
1465007 1.19/1 110 110 M 14x1,5 x 163 17 17 18 5,0 2 1.3
1465015 1.19/2 160 140 M 18x1,5 x 215 19 21 20 6,5 3 2.5
1465023 1.19/3 200 200 G 1/2 x 282 22 22 22 7,5 5 4.0
1.20 Puller
with clamping yoke
These pullers are mainly employed for removing car and truck
steering arms. The clamping yoke presses the hooks firmly
behind the part to be removed and prevents the puller from
slipping out of position.
Code No. amax bA$c d e max. t 0
8008050 1.20/1 90 85 M 18x1,5 x 130 19 22 12 3,0 5,0 1.2
8008130 1.20/2 90 100 M 18x1,5 x 130 19 24 15 3,0 5,0 1.8
8008210 1.20/3 150 140 G 1/2 x 175 22 30 18 3,5 7,5 3.3
1.22 Puller
with clamping yoke
Due to its double-ended hooks, this tool is particularly suitable for
separating and removing flush-seated parts, such as axle bearings,
pinions, etc. Especially economical, this is a multi-functional tool to
cover a range of sizes.
Code No. amax bA$c d e max. t 0
8009020 1.22/1 110 170 M 18x1,5 x 200 19 25 14 3,5 5,0 2.1
8009100 1.22/2 160 260 G 1/2 x 350 22 25 14 3,5 7,5 4.1
8009290 1.22/3 160 325 G 1/2 x 350 22 25 14 3,5 7,5 4.5
Baldur_9_GB.mif Seite 331 Freitag, 18. Juli 2003 10:15 10
332
1.23 Puller
with slim hooks
For removing bearings in confined spaces.
The scissor-pattern hook design means that the hooks are pressed
firmly onto the part during the removal procedure.
Code No. amax bA$c d e max. t 0
8084580 1.23/1S 80 85 M 10 x 105 12 11 4,5 2,5 1,5 0.4
8084310 1.23/1 80 85 M 10 x 105 12 23 4,5 2,5 2,0 0.4
8084660 1.23/2 120 120 M 14x1,5 x 130 17 31 5,0 3,5 3,5 0.8
8084740 1.23/3 120 150 M 14x1,5 x 205 17 31 5,0 3,5 3,5 1.0
1.26 Nut splitter
For splitting jammed or stripped nuts without damaging
the bolt thread. Suitable for nuts up to property class 6.
Code No. for nuts up to A$ 0
8009880 1.26/1 SW 17, M 10 M 14x1,5 x 37 17 0.2
8009610 1.26/2 SW 24, M 16 M 14x1,5 x 37 17 0.3
8010030 1.26/3 SW 36, M 24 M 22x1,5 x 70 24 1.0
1.26/12 Nut splitter set
In plastic wallet.
Code No. Contents 1 each 0
8010110 1.26/12 1.26/1 1.26/2 0.5
1.26 HYD Nut splitter
hydraulic
With strong chisel, additionally induction hardened at the
cutting edge for breakage resistance. The chamfer at the chisel's
edge improves the splitting effect and prevents breakage.
With smooth chisel function.
Channel walls rolled, thus mirror-smooth and wear resistant.
No force necessary when turning back the chisel.
For nuts up to property class 10.
Code No. for nuts up to max. t 0
8009450 1.26/1 HYD SW 7 - SW 22, M 4 - M 14 5 0.7
8009530 1.26/2 HYD SW 22 - SW 36, M 14 - M 24 13 3.8
1.28 Stud extractor
For inserting and removing studs.
These tools will reliably grip even extremely short stud ends.
Slim pattern.
Code No. u-Stud $ /
8010620 1.28/1 6-13 19 230
8010700 1.28/2 8-19 19 300
8010890 1.28/3 19-25 19 390
1.28/4 Stud extractor
For inserting and removing studs.
These tools will reliably grip even extremely short stud ends.
Code No. u-Stud $ /
1465031 1.28/4 5-26 19 390
Baldur_9_GB.mif Seite 332 Freitag, 18. Juli 2003 10:15 10
333
1.29 Ball bearing extractor
These special extractors have been developed for removing ball
bearings that are both on a shaft and in a housing.
These hooks selected using the table are inserted into the ball race,
evenly distributed in the outer ring according to the number of
balls. The support rings supplied for the ball bearings to be
removed are placed on the bearings’ inner races.
The bridge with spindle is then placed on the centering depression
of the shaft and the spindle put under tension with the hooks.
Code No. A$ /
8011000 1.29/1 M 10 x 160 14 150
8011190 1.29/2 M 12 x 195 14 280
8011270 1.29/3 M 14 x 210 17 420
8011350 1.29/4 M 18 x 230 19 750
8011430 1.29/5 M 20 x 235 22 1100
1.29 Pulling hooks
set of 4 pieces
* Support rings are used for pulling these bearings.
Code No. yfor bridge - for ball bearing No. /
8011510 1.29/10 145 1.29/1 - 6000 6001 6002 80
8011780 1.29/15 145 1.29/1 - 6003 6004 6005 6200 6201 6202 100
8011860 1.29/20 177 1.29/2 - 6006 6203 200
8011940 1.29/25 177 1.29/2 - 6007 6008 6009 6010
6204 6205 6300 6301 6302 200
8012080 1.29/30 185 1.29/2 - 6303 6304
1.29/3 - 6011 6012 300
8012160 1.29/35 187 1.29/3 - 6206 6207 6208 6305 400
8012240 1.29/40 235 1.29/4 - 6209 6210 600
8110250 1.29/45 236 1.29/4 - 6211 6212 6308* 6404 6405
1.29/5 - 6309* 6310* 6311* 6406* 800
1.29 K Ball bearing extractor set
In sheet metal case, dimensions: 285 x 190 x 75 mm.
Code No. Contents 0
8110330 1.29/1K 3 hubs with spindle 1.29/1 - 1.29/3
6 sets hooks 1.29/10 - 1.29/35
1 plug-in handle 1.29/0 4.7
8012320 1.29/3K 5 hubs with spindle 1.29/1 - 1.29/5
6 sets hooks 1.29/10 - 1.29/45
1 plug-in handle 1.29/0 and 4 support rings 8.0
Tool inventory at the
professional fire brigade in Bochum.
Baldur_9_GB.mif Seite 333 Freitag, 18. Juli 2003 10:15 10
334
1.92 Ball bearing extractor PLUS
Using the new BALDUR ball bearing extractor, the removal
of shaft-mounted ball bearings in a housing is now possible
without any problems. Due to its great degree of functionality
combined with the simplified handling, this novel design makes
a PLUS in effectiveness and productivity possible.
This tool is distinguished by its extreme user-friendliness.
The hooks are fixed in the slot.
The self-locking arrangement means that the force applied
is 100% utilised. Secure at all times against slipping off - and a
straight pulling force for precise working.
Suitable for more than 40 standard ball bearings
up to 6311.
* with supporting ring 6309
** with supporting ring 6310
*** with supporting ring 6311
Code No. Bearing Hook Head size
1553534 1.92/1
6000
6001
6002
6003
6200
6201
6202
6203
6004
6005
6006
6300
6301
6302
6007
6008
6204
6009
6010
6205
6303
6304
10
10
10
10
10
20
20
20
20
20
20
30
30
30
40
40
40
40
40
40
40
40
1-7
1-4
1-3
1-4
1-4
1-7
1-4
1-4
1-3
1-3
1-3
1-3
1-3
1-7
1-3
1-3
1-4
1-3
1-3
1-3
1-7
1-7
1553542 1.92/2
6011
6012
6206
6207
6305
6403
6306
6307
6208
6209
6210
6211
6407*
6404
6405
6406
6308
6309
6212
6310**
6311***
50
50
50
50
50
60
60
60
60
60
60
60
60
70
70
70
70
70
70
70
70
2-3
2-3
2-3
2-3
2-7
2-3
2-4
2-4
2-3
2-3
2-3
2-3
2-3
2-7
2-7
2-7
2-4
2-4
2-3
2-4
2-4
1553550 1.92/12
Contents of set
1.92/1 and
1.92/2
Baldur_9_GB.mif Seite 334 Freitag, 18. Juli 2003 10:15 10
335
1.30 Internal extractor
For extremely-tightly-packed ball bearings, bearing races,
bushings, and oil seals®.
Operation:
The internal extractor is inserted into the bearing and the spindle
screwed in. The sharp turned-out shoulders of the pulling shell
jaws will press outwards behind the part to be extracted.
The counter-support brace is then added. Both feet must
be aligned parallel to the spindle to ensure rigidity.
Code No. p C $ /
8012750 1.30/0 M 10 5-8 10 150
8012830 1.30/1 M 10 8-12 10 160
8012910 1.30/2 M 10 12-15 10 170
8013130 1.30/3 M 10 15-19 14 170
8013480 1.30/4 M 10 19-25 14 200
8013560 1.30/4A M 10 25-30 14 300
8013640 1.30/5 M 10 30-35 14 350
8013720 1.30/6 M 14x1,5 35-45 17 650
8013800 1.30/7 M 14x1,5 45-55 17 800
8013990 1.30/8 M 14x1,5 55-70 19 1400
8014020 1.30/9 M 14x1,5 70-100 27 2900
1.30 N Internal extractor
with reinforced shoulder
Especially suitable for the safe and trouble-free extraction of needle
roller bearings, ball bearings and brass sleeves from crankshafts.
Note:
The soulder of the shell jaw must be applied behind the bearing.
Code No. p C $ /
8013050 1.30/2N M 10 12-14 10 170
8013210 1.30/3N M 10 14-19 14 170
1.30/10 Internal extractor
Suitable for removing large ball bearings and bearing outer races.
Operation:
The extraction jaws are spread by turning the nut.
The newly-developed spreading system enables a simple,
step-free and time-saving adjustment to the desired diameter
to be made. The sharp-edged sections of the extraction jaws
seat flush beneath when spread.
Code No. p C $ /
8014100 1.30/10 G 1/2" 60-160 36 2450
1.35 Impact bearing puller
Suited for the removal of small ball bearings since there is often not
enough room for support braces.
Code No. for internal extractor with adaptor p $ /
8016070 1.35/1 1.30/1 - 1.30/2 -M 10 17 550
8039010 1.35/2 1.30/0 - 1.30/7 M 14 x 1,5 M 10 24 3200
1.35/2
1.35/1
1.30/0-9
1.30/2N
Baldur_9_GB.mif Seite 335 Freitag, 18. Juli 2003 10:15 10
336
1.36 Support brace
For internal extractors Nos. 1.30/0 – 1.30/9.
Operation:
The support brace is placed on the housing and the spindle
screwed onto the spindle of the internal extractor.
The toggle is held firmly, and the bearing extracted
by tightening the nut.
Code No. for internal extractor p $ /
8016580 1.36/1 1.30/1 - 1.30/5 M 10 27 600
8016660 1.36/2 1.30/6 - 1.30/8 M 14x1,5 32 1400
8016740 1.36/3 1.30/9 M 14x1,5 32 3000
1.36/4 Support brace
For internal extractor No. 1.30/10.
Operation see No. 1.36
Code No. for internal extractor p $ /
8016820 1.36/4 1.30/10 G 1/2" 36 7700
1.31 Internal extractor set
The handy sheet metal case contains the most used extractor
sizes for the removal of ball bearings, bearing races, bushings,
oil seals®, etc.
Code No. Contents 0
8014450 1.31/0N 4 internal extractors 12-30 mm 1.30/2 -3 -4 -4A
1 support brace 1.36/1 2.4
8014530 1.31/0 4 internal extractors 12-30 mm 1.30/2N -3N -4 -4A
1 support brace 1.36/1 2.4
8014610 1.31/1 6 internal extractors 12-46 mm 1.30/2 - 6
2 support braces 1.36/1 - 2 5.9
8014880 1.31/2 8 internal extractors 12-70 mm 1.30/2 - 8
2 support braces 1.36/1 - 2 10.0
1.32 Set of internal and external extractors
In a handy sheet metal case. Sets comprise internal extractors,
support braces, pulling chucks, external extractors and stud
extractors.
Code No. Contents 0
8015260 1.32/1
6 internal extractors 12-46 mm 1.30/2 - 6
2 support braces 1.36/1 - 2
1 pulling chuck 1.44
1 battery-terminal puller 1.12/02
1 puller, 2-arm pattern 1.06/1
10.0
8015340 1.32/2
8 internal extractors 12-70 mm 1.30/2 - 8
2 support braces 1.36/1 - 2
1 pulling chuck 1.44
1 battery-terminal puller 1.12/02
2 pullers, 2-arm pattern 1.06/1 - 2
1 stud extractor 1.28/1
19.0
1.36/1-3
1.36/4
1.32/1
1.32/2
Baldur_9_GB.mif Seite 336 Freitag, 18. Juli 2003 10:15 10
337
1.37 Cylinder liner puller
complete with support brace
Wet heavy-vehicle (e.g. Daimler Benz, MAN) cylinder liners,
automobile and stationary-engine liners, and other parts
may be extracted using this puller.
Operation:
The spindle of the support brace is screwed into the clamping
nut of the puller, and the puller inserted into the liner.
The support brace is placed on to the cylinder block.
Due to the newly-developed spreading system, when the spindle
is turned, all three jaws spread quickly and without difficulty,
until they are firmly seated beneath the edge of the liner.
Then the nut of the support brace is tightened.
Code No. p C $ /
8017200 1.37/2 G 1/2" 60-160 36 6800
1.38 V Extension rod
For separator puller No. 1.38.
Code No. for separator p y 0
8018440 1.38/AV 1.38/0 1.38/1 M 10 100 0.2
8018520 1.38/CV 1.38/2 M 14 x 1,5 100 0.5
8018600 1.38/DV 1.38/3 M 18 x 1,5 100 0.6
8018790 1.38/EV 1.38/4 M 22 x 1,5 200 2.1
8018870 1.38/FV 1.38/5 M 24 x 1,5 200 2.7
1.38 Separator puller
These separator pullers are used together with the bearing
separators No. 1.40. The tension bolts are screwed into the
threaded holes in the bearing separators.
Code No. for separator a b A$ p / p top Hydraulic spindle 0
8017550 1.38/0 1.40/0 40-120 160 M 14 x 120 17 M 10 / M 12x1,5 1.0
8017630 1.38/1 1.40/1 60-165 230 M 18 x 170 19 M 10 / M 14x1,5 2.4
8017710 1.38/2 1.40/2 70-215 250 G 1/2 x 210 22 M 14x1,5 / M 16x1,5 1.06/HSP1 3.8
8017980 1.38/3 1.40/3 90-300 270 G 3/4 x 280 27 M 18x1,5 / M 20x1,5 1.06/HSP2 7.2
8018010 1.38/4 1.40/4 125-380 350 G 1 x 310 36 M 22x1,5 / M 24x1,5 1.06/HSP3 11.3
8018280 1.38/5 1.40/5 140-440 400 G 1 x 360 36 M 24x1,5 / M 26x1,5 1.06/HSP3 16.3
Baldur_9_GB.mif Seite 337 Freitag, 18. Juli 2003 10:15 10
338
1.38 HSP Separator puller
hydraulic, for separating blades
These pullers are used together with the separating
blades No. 1.40. The tension bolts are screwed into the
threaded bores of the separating blades.
Code No. for separator a b p 0
8014960 1.38/2-HSP1 1.40/2 70-215 175 M 14 x 1,5 4.0
8015180 1.38/3-HSP2 1.40/3 90-300 195 M 18 x 1,5 6.8
8015420 1.38/4-HSP3 1.40/4 125-380 240 M 22 x 1,5 11.8
8015500 1.38/5-HSP3 1.40/5 140-440 290 M 24 x 1,5 16.6
Code No. for puller p O 0
8019680 1.40/0 1.38/0 M 10 5-60 0.4
8019760 1.40/1 1.38/1 M 10 12-75 1.0
8019840 1.40/2 1.38/2 M 14 x 1,5 22-115 2.3
8019920 1.40/3 1.38/3 M 18 x 1,5 30-155 4.4
8020180 1.40/4 1.38/4 M 22 x 1,5 30-200 8.9
8020260 1.40/5 1.38/5 M 24 x 1,5 30-250 15.3
1.41 Separator and puller set
Set in sheet metal case, comprising separator, puller, and
extension rods. Dimensions: 420 x 320 x 80 mm.
Code No. Contents 0
8109750 1.41/0 1.38/0 1.38/AV 1.40/0 2.8
8109830 1.41/1 1.38/1 1.38/AV 1.40/1 4.1
8109910 1.41/2 1.38/2 1.38/CV 1.40/2 9.1
8110090 1.41/3 1.38/3 1.38/DV 1.40/3 16.1
8110170 1.41/4 1.38/4 1.38/EV 1.40/4 28.6
1.40/15 Drive shaft bearing puller
Operation:
The separator blades are placed evenly behind the bearing and the
pulling arms aligned parallel to the axle and spindle.
Code No. Aperture yA$ 0
8010380 1.40/15 45-75 750 G 1/2 x 160 22 11.8
1.40/16 Set of hooks
2 pieces
These hooks, together with the crossbeam and separator blades
of No. 1.40/15, are used for mounting drive-shaft bearings.
Operation:
The separator blades are placed with the flat side behind the
bearing, and the hooks inserted behind the clamping bolt of the
separator blades. When the spindle is tightened, the bearing is
pulled against the axle flange.
Code No. Description 0
8010460 1.40/16 1 pair hooks as illustrated 1.4
8010540 1.40/16A Crossbeam with spindle 2.2
1.40/16A
1.40/16
1.40/15
Baldur_9_GB.mif Seite 338 Freitag, 18. Juli 2003 10:15 10
1.40 Bearing separator
For removing taper roller and ball bearings, inner bearing races,
and other tightly-seated or thin-walled parts.
Operation:
To remove tightly-seated parts, the sharp edges of the separator
blades are pressed behind the part and it is then withdrawn using
the correct puller No. 1.38. To avoid damage to delicate parts, the
flat surfaces of the separator blades are used. This produces a
large support surface that prevents deformation.
339
1.44 Pulling chuck
For removing the inner races of dynamos, magnetos, motors, and
other machine parts. Simple operation by tightening the cap nut.
Code No. Clamping range mm Clamping reach mm 0
8022040 1.44/1 5-32 125 1.4
Forging of the heavy-duty puller crossbeams
in the BALDUR works in Remscheid.
1.50 Hydraulic pump and cylinder set
This hydraulic set, consisting of hand pump 1.50/1 and hydraulic
cylinder 1.51, is suitable for pressing, straightening, lifting,
bending, and pulling.
Code No. consisting of: 0
8110410 1.50/10 Hydraulic hand pump 1.50/1
Hydraulic cylinder 1.51/10 11.0
8110680 1.50/11 Hydraulic hand pump 1.50/1
Hydraulic cylinder 1.51/11 13.0
1.50/1 Hydraulic hand pump
Supplied complete with 1.50 m high-pressure hose,
to fit hydraulic cylinder 1.51.
Code No. for hydraulic cylinder 0
8022710 1.50/1 1.51/10 1.51/11 7.0
1.51 Hydraulic cylinder
Code No. Stroke height mm max. t 0
8023440 1.51/10 140 10 4.0
8110760 1.51/11 200 10 6.0
Baldur_9_GB.mif Seite 339 Freitag, 18. Juli 2003 10:15 10
340
1.06 Puller
for hydraulic implement 1.50
For the fast and damage-free removal of pulleys, wheels, ball
bearings, etc. Robust pattern, designed for rigidity and heavy
duty use. By reversing the hooks, this tool may be used as an
internal or external puller. The reach may be increased both by
using pulling hooks in special lengths, and by using extensions.
Code No. a1a2 min a2 max b c d e max. t 0
8112620 1.06/40 520 185 600 200 36 28 6,5 10 11.0
8113000 1.06/50 640 230 715 225 50 33 10,0 18 24.0
1.15 H Puller
for hydraulic implement 1.50
Heavy duty pattern for the removal of gear wheels, spoked wheels,
pulleys, etc. The hook tips grip automatically. The hooks may be
moved to use this tool as a 2-arm puller. The adjustable reach
means that this puller is very versatile.
Code No. amax b c d e max. t 0
8006860 1.15/30 250 260 32 18 3,5 12 9.0
8109590 1.15/40 280 390 32 20 3,5 12 9.5
1.17 H Puller
for hydraulic implement 1.50
Heavy duty pattern for the removal of gear wheels,
spoked wheels, pulleys, etc.
The hook tips grip automatically.
Code No. amax b c d e max. t 0
8007590 1.17/10 300 300 36 19 3,5 12 11.4
8109670 1.17/20 425 425 36 22 3,5 12 12.3
Baldur_9_GB.mif Seite 340 Freitag, 18. Juli 2003 10:15 10
341
1.55 Hydraulic press
This piece of auxiliary equipment considerably increases the
capability of the standard pressure spindle.
Operation:
With pressure released, the press is placed between the pressure
spindle and the end of the shaft. The pressure spindle is then
tightened firmly. Care must be taken that the centreline of the
shaft, the hydraulic press, and the pressure spindle are exactly in
alignment. Then the hydraulic spindle is screwed inwards.
Important note: Release the hydraulic press after use.
Code No. Stroke height mm Installed height mm max. t 0
8024090 1.55/1 10 75 8 0.7
8024170 1.55/2 15 90 15 1.3
1.60 Wheel-hub puller
For cars and trucks with wheel stud circles up to 225 mm.
Easy to use. With wheel stud protection using rotating nut
apertures that always lie flat to the hub. Spindle may be exchanged
for hydraulic pressure spindle (see table).
Code No. No. of hooks AHydraulic spindle 0
8024840 1.60/3 3 G 3/4 x 200 1.06/HSP2 4.0
8110840 1.60/5 4 G 3/4 x 200 1.06/HSP2 4.5
8024920 1.60/4 5 G 3/4 x 200 1.06/HSP2 5.0
8110920 1.60/H 1 spare hook 0.5
1.60 HSP Wheel-hub puller
hydraulic
For cars and trucks with wheel stud circles up to 225 mm.
Easy to use. With wheel stud protection using rotating nut
apertures that always lie flat to the hub.
Code No. No. of hooks A0
8015690 1.60/3-HSP2 3 1.06/HSP2 4.6
8015770 1.60/4-HSP2 4 1.06/HSP2 5.1
8015850 1.60/5-HSP2 5 1.06/HSP2 5.6
1.61 Wheel-hub puller
For cars and trucks with wheel stud circles up to 250 mm.
Simple use. Just place the plate with the spindle on the centre-
marking of the axle and fold back the hooks onto the plate.
With swivelling nut holders always lying flat on the hub to prevent
wheel-stud damage. Spindle may be exchanged for hydraulic
pressure spindle (see table).
Code No. No. of hooks AHydraulic spindle 0
8111060 1.61/3 3 G 3/4 x 200 1.06/HSP2 5.0
8111140 1.61/4 4 G 3/4 x 200 1.06/HSP2 5.6
8025300 1.61/5 5 G 3/4 x 200 1.06/HSP2 6.2
8111220 1.61/H 1 spare hook 0.6
1.60/3
1.60/H
1.60/5-HSP2
1.61/5
Baldur_9_GB.mif Seite 341 Freitag, 18. Juli 2003 10:15 10
342
1.61 HSP Wheel-hub puller
hydraulic
For cars and trucks with wheel stud circles up to 250 mm.
Easy to use. With wheel stud protection using rotating nut
apertures that always lie flat to the hub.
Code No. No. of hooks Hydraulic spindle 0
8015930 1.61/3-HSP2 3 1.06/HSP2 5.6
8016150 1.61/4-HSP2 4 1.06/HSP2 6.2
8016230 1.61/5-HSP2 5 1.06/HSP2 6.8
1.62 Wheel-hub puller
For trucks with wheel stud circles up to 350 mm. Easy to use.
With wheel stud protection using rotating nut apertures that
always lie flat to the hub. This tool may also be used with the
hydraulic aid without requiring a reduction bushing.
Code No. No. of hooks AHydraulic spindle 0
8026030 1.62/8 8 G 1 x 310 1.06/HSP3 10.5
8111220 1.61/H 1 spare hook 0.6
1.62 HSP Wheel-hub puller
hydraulic
For trucks with wheel stud circles up to 350 mm. Easy to use.
With wheel stud protection using rotating nut apertures that
always lie flat to the hub.
Code No. No. of hooks A0
8016310 1.62/8-HSP3 8 1.06/HSP3 11.9
1.64 Drive shaft puller
Suitable for drive shafts with 4 or 5 apertures.
For wheel stud circles 100-180 mm.
Operation:
The puller is attached to the drive shaft flange using the nuts of the
wheel bolts. By striking the spindle head with the sliding hammer,
the shaft may be removed easily and without damage.
Code No. p 0
8026700 1.64/1 max. M14 3.8
1.65 Pulling flange
The flange possesses slots for hole pitches of 180, 120, and 90
degrees. Additional holes may be drilled to render the flange
suitable for other pitches and aperture diameters. A very sturdy
model for heavy parts and the highest requirements.
Spindle may be exchanged for hydraulic pressure spindle
(see table).
Code No. Stud ,AHydraulic spindle 0
8027000 1.65/1 up to 16 G 1 x 270 1.06/HSP3 16.3
1.62/8
Baldur_9_GB.mif Seite 342 Freitag, 18. Juli 2003 10:15 10
343
1.66 Pulling flange
For wheels and discs with tapped holes up to M10.
The flange is fitted with slots for hole pitches of
180 and 120 degrees, and using one pair each of long
and short hooks and a protective cap for the thread of the
steering column, this tool is suitable as a steering wheel puller.
Code No. Stud ,A$ 0
8027510 1.66/1 up to 10 M 12 x 110 14 0.7
8027780 1.66/11 with hooks in length 85 + 135 mm,
1 pair each M 12 x 110 14 1.0
1.67 Steering-wheel puller
Steering-wheel puller for cars.
The puller includes one pair of short hooks, one pair of long hooks,
and a protective cap for the thread of the steering column.
Code No. Clamping reach Hook length up to A$ 0
8028240 1.67/1 35-90 135 M 14x1,5 x 150 17 0.6
1.68 Steering-wheel puller
Steering-wheel puller featuring one pulling ring each with
100 mm and 150 mm diameter for 3-spoke and 4-spoke
steering wheels. To protect the steering-wheels, the pulling
rings are fitted with sliding rubber sleeves.
Code No. Hook length mm A$ 0
8028750 1.68/1 120 M 18 x 170 19 2.0
1.70 Dismantling and assembly fork
The wedge-shaped fork end makes the fast removal of track
rod and push rod ends, steering arms, and other steering parts
possible. Also suitable for removing shock absorbers and other
separating and dismantling work.
The forks are suitable for use in the most confined spaces.
Hammer blows on the handle ends are used to separate the parts.
Code No. A mm B mm C mm 0
8029210 1.70/1 18 340 80 0.8
8029480 1.70/2 23 340 80 0.8
8029560 1.70/3 29 350 90 1.0
8029640 1.70/4 40 350 90 1.1
8085040 1.70/5 45 355 95 1.2
Baldur_9_GB.mif Seite 343 Freitag, 18. Juli 2003 10:15 10
344
1.74 Universal ball joint puller
For removing the ball joint journals on track rods, stabilizers, etc.
Simple operation due to slender lower part and two-stage
lever position.
Code No. OClamping height Fork depth 0
8085200 1.74/1 20 12-50 35 1.0
8085390 1.74/2 20 50-80 35 1.4
1.75 Oil filter hook
3-arm pattern
For removing firmly seated oil filters.
Code No. ODrive 0
8117420 1.75/1 60-120 without adaptor G 3/8,
with adaptor 17 mm external, G 1/2 internal 0.6
1.73 Universal ball joint puller
For removing ball joints on cars and trucks.
Code No. OClamping height Fork depth 0
8030810 1.73/1 23 65 24 0.7
8033240 1.73/3 32 85 28 2.4
1.72 Ball joint puller
For the simple and damage-free removal of ball pins on track
rods and push rods.
Code No. a b c A$ 0
8030300 1.72/1 18 35 40 M 14x1,5 x 50 17 0.3
8030490 1.72/2 23 45 50 M 14x1,5 x 50 17 0.5
8030570 1.72/3 27 56 60 M 18x1,5 x 80 19 0.7
8030650 1.72/4 37 78 75 G 1/2 x 110 22 1.5
1.76 Cartridge spanner
3-arm pattern
For removing firmly seated granulate cartridges.
Code No. ODrive 0
1523651 1.76/1 80-150 1/2" 0.6
Baldur_9_GB.mif Seite 344 Freitag, 18. Juli 2003 10:15 10
345
1.78 P Universal coil spring compressor
A coil spring compressor for MacPherson suspension strut and
transverse link axles with spring diameters of 110-180 mm.
Shock absorbers may be replaced without removing the
suspension struts.
The safety holder renders slipping impossible.
VPA-GS-tested safety.
The hooks are drop forged.
The wide support rests are matched to the coil spring pitch.
Code No. Clamping reach mm max. t 0
8111300 1.78/P1 240 3,5 3.5
8031030 1.78/PK1 240 3,5 3.5
1.79 Spring spreader
This has been especially designed for VAG exhaust installations,
where the pipe is not held by bolts to the exhaust manifold,
but clamped on using springs.
Code No. 0
8112540 1.79/1 0.4
1.78 S Safety coil spring compressor
Safety coil spring compressor for the safe installation and
removal of coil springs with a diameter of 110–180 mm.
The spindles (M18) have 13 mm hexagon drive nut, so that when
compressing the springs, they turn downwards, thus preventing
damage to bodywork above the springs.
Safety note:
When the spindles are tightened evenly, the clamping heads
grip the coils tightly, rendering sideways slip impossible.
VPA-GS-tested safety.
Code No. Clamping reach mm 0
8031110 1.78/S1 180 2.2
8031380 1.78/S2 280 2.5
8031460 1.78/S3 380 2.8
d
1.78/P1
1.78/PK1
d
Baldur_9_GB.mif Seite 345 Freitag, 18. Juli 2003 10:15 10
346
1.80/2 Spindle pressure pads
for axle bores (hollow shafts)
See No. 1.80/1 for description.
Code No. Plate ,Holder , 0
1120700 1.80/2
67
70
73
78
83
90
54
57
60
64
70
76
2.3
1.80/3 Spindle pressure pads
for axle bores (hollow shafts)
See No. 1.80/1 for description.
Code No. Plate ,Holder , 0
1120719 1.80/3
41
44
48
50
54
60
64
67
70
73
78
83
90
32
35
38
41
44
48
50
54
57
60
64
70
76
4.2
1.81/1 Threaded inserts
The BALDUR threaded inserts make the removal of threaded
caps, for example, possible, when these possess one threaded
hole.
For slide hammers 1.35/1, 1.35/2, threaded support 1.36/1.
Code No. Connecting / Insert thread /
1120727 1.81/1
M 10 - M 4
M 10 - M 5
M 10 - M 6
M 10 - M 8
M 10 - M 10
M 10 - M 12
200
1.80/1 Spindle pressure pads
for axle bores (hollow shafts)
The BALDUR pressure pads are used for the removal of such
parts as bearings and gear wheels that are mounted on hollow
shafts or in housings. Here, the spindle pressure pad serves as
a counter-axis to the BALDUR puller, where the spindle now
transfers the force to the pressure pad.
Code No. Plate ,Holder , 0
1120697 1.80/1
25
28
32
35
41
44
48
50
54
60
64
19
22
25
28
32
35
38
41
44
48
50
2.2
1.81/2 Threaded inserts
See No. 1.81/1 for description.
For slide hammers 1.35/2, 1.36/2, threaded support 1.36/3.
Code No. Connecting / Insert thread /
1120743 1.81/2
M 14x1,5 - M 8
M 14x1,5 - M 10
M 14x1,5 - M 12
M 14x1,5 - M 14
M 14x1,5 - M 16
M 14x1,5 - M 18
470
Baldur_9_GB.mif Seite 346 Freitag, 18. Juli 2003 10:15 10
347
1.81/10 Threaded inserts
for 1-hole and 2-hole uses, 2 each
The BALDUR threaded inserts make the removal of threaded caps,
for example, possible, when these possess one or two threaded
holes. For separator puller 1.38/0, 1.38/1.
Code No. Connecting / Insert thread /
1120735 1.81/10
M 10 - M 4
M 10 - M 5
M 10 - M 6
M 10 - M 8
M 10 - M 10
M 10 - M 12
Adaptor
460
1.81/20 Threaded inserts
for 1-hole and 2-hole uses, 2 each
See No. 1.81/10 for description.
For separator puller 1.38/2.
Code No. Connecting / Insert thread /
1120751 1.81/20
M 14x1,5 - M 8
M 14x1,5 - M 10
M 14x1,5 - M 12
M 14x1,5 - M 14
M 14x1,5 - M 16
M 14x1,5 - M 18
Adaptor
1010
1.85/1 Professional plastic bearing
installation set
This sturdy plastic bearing installation set combines the
advantages of the usual models in metal with the advantages
of plastic. The impact-resistant plastic is handily light, but
just as robust as the metal variants.
Using this bearing installation set, which consists of 33 impact
rings, more than 200 types of bearings may be re-installed
effortlessly and without damage. The set is completed with three
aluminium impact sleeves and a recoil-free bodywork hammer with
nylon heads, all in a strong plastic case. This set guarantees that
the installed bearings will suffer no damage that might have
happened when working "metal to metal". No deformations of the
bearing housings, sealing rings, or shafts.
Code No. Contents 0
1120778 1.85/1 Impact rings 10-50 mm, for external Ø 26-110 mm,
hammer 1,2 kg,
case dimensions 450 x 360 x 140 mm 4.6
1.91 Tyre removing tool
For breaking the adhesion between truck tyres and wheel rims.
Code No. y 0
8032270 1.91 300 1.8
Adaptor
Threaded insert
Baldur_9_GB.mif Seite 347 Freitag, 18. Juli 2003 10:15 10
348
2.10 Automobile workshop set
Add-on system
Clearly arranged module system,
everything at hand on perforated wall-board.
Code No. Contents 0
1088696 2.10 as below stated 11.5
Code No. Description Qty.
1076469 106/103 Cross piece, 2-arm pattern, 140 mm 1
1076981 107/103 Cross piece, 3-arm pattern, 140 mm 1
1120514 106/A Pulling hook, 100 mm 3
1175343 106/S100 Pulling hook, slim pattern, 100 mm 3
8003840 1.12/02 Battery-terminal puller, 2-arm pattern 1
8009610 1.26/2 Nut splitter 1
8010700 1.28/2 Stud extractor 1
8029480 1.70/2 Dismantling and assembly fork 1
8030810 1.73/1 Universal ball joint puller 1
8117420 1.75/1 Oil filter hook 1
1120638 71010 Perforated board 1
1081616 1500 H 1 Hook 4
1081624 1500 H 2 Spring clamp 9
1081632 1500 H 3 Spring clamp 5
2.20 Truck workshop set
Add-on system
Clearly arranged module system,
everything at hand on perforated wall-board.
Code No. Contents 0
1088718 2.20 as below stated 14.0
Code No. Description Qty.
1076612 106/2A03 Cross piece, 2-arm pattern, 260 mm 1
1077023 107/2A03 Cross piece, 3-arm pattern, 260 mm 1
1120530 106/B Pulling hook, 100 mm 3
1175475 106/S220 Pulling hook, slim pattern, 220 mm 3
1123947 106/BV Pulling hook, 300 mm 3
1084593 1.2106210 Spindle 1
8116100 1.06/HSP1 Hydraulic pressure spindle 1
8019840 1.40/2 Bearing separator 1
1120638 71010 Perforated board 1
1081616 1500 H 1 Hook 10
1081632 1500 H 3 Spring clamp 5
2.30 Industrial pulling set
Add-on system
For the assembly of the tried and tested 1.06 and 1.07 versions.
Using this set, you will be able to assemble more than 12 of the
usual versions with high-speed clamping hooks, including
hydraulic spindle, in seconds.
Code No. Contents 0
1393014 2.30 as below stated 17.5
Code No. Description Qty.
1076469 106/103 Cross piece, 2-arm pattern, 140 mm 1
1076485 106/1A03 Cross piece, 2-arm pattern, 180 mm 1
1076590 106/203 Cross piece, 2-arm pattern, 220 mm 1
1076612 106/2A03 Cross piece, 2-arm pattern, 260 mm 1
1076981 107/103 Cross piece, 3-arm pattern, 140 mm 1
1077007 107/1A03 Cross piece, 3-arm pattern, 180 mm 1
1077015 107/203 Cross piece, 3-arm pattern, 220 mm 1
1077023 107/2A03 Cross piece, 3-arm pattern, 260 mm 1
1084488 1.1406140 Spindle 1
1084593 1.2106210 Spindle 1
8116100 1.06/HSP1 Hydraulic pressure spindle 1
1178199 106/A-E Pulling hook 3
1178253 106/B-E Pulling hook 3
1120638 71010 Perforated board 1
1081616 1500 H 1 Hook 12
1081624 1500 H 2 Spring clamp 4
1081632 1500 H 3 Spring clamp 6
Baldur_9_GB.mif Seite 348 Freitag, 18. Juli 2003 10:15 10
349
2.40 Pulling set for construction machines
Add-on system
For the assembly of the robust and handy strap-pattern pulling
tools 1.14 and 1.15.
With this set, you will be able to assemble 10 of the usual
flexible strap-pattern pulling tools from the range 1.14/1.15,
including the new hydraulic spindle.
Code No. Contents 0
1393030 2.40 as below stated 24.5
Code No. Description Qty.
1077856 114/204 Head 1
1077910 114/304 Head 1
1078054 115/204 Head 1
1078070 115/304 Head 1
1084569 1.1806200 Spindle 1
1084631 1.2106250 Spindle 1
8116100 1.06/HSP1 Hydraulic pressure spindle 1
1077821 114/201 Pulling hook, 210 mm 3
1077899 114/301 Pulling hook, 260 mm 3
1077953 114/401 Pulling hook, 390 mm 3
1077872 114/208 Strap 6
1077937 114/308 Strap 6
1120638 71010 Perforated board 1
1081616 1500 H 1 Hook 6
1081624 1500 H 2 Spring clamp 2
1081632 1500 H 3 Spring clamp 20
Code Accessories No. Qty.
1075225 Hexagon bolt M10 6
1075144 Hexagon bolt M12 12
1074946 Hexagon nut M10 6
1074954 Hexagon nut M12 12
1074431 Spring washer M10 6
1074458 Spring washer M12 12
3.01 Track alignment gauge
For inside measurement.
Suitable for all vehicle types.
With simple, telescopic length adjustment.
Immediate track-difference readings may be taken from the
milimetre scale. Extensive measurement range from 835
to 1500 mm, and with extensions up to 2100 mm.
Track difference measurable from 0–35 mm.
Notes on Use:
The vehicle to be tested must be standing on level ground.
The front wheels must be set for running straight ahead and have
the same tyre pressure.
The play in the steering linkage must be removed by pressing the
front wheels apart.
The track alignment gauge must be set roughly at the axle centre-
line between the front tyres in such a manner that the two chain
ends contact the ground.
The scale is set a “0“.
The car is allowed to roll forward approx. one half turn of the wheel,
until the chain ends again contact the ground.
The track difference may then be read off on the scale.
Code No. Description Measurement range 0
8033080 3.01 Track alignment gauge 835-1500 2.0
8033160 3.01/V Extension for track alignment gauge 1500-2100 0.4
Dump truck at work.
Baldur_9_GB.mif Seite 349 Freitag, 18. Juli 2003 10:15 10
