3M
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering inform at io n cal l
800-225-5373
3M™ Boardmount Socket
.100″ Low Profile, Straight, Solder Tails 929 Series
Physical
Electrical
Environmental
Insulation
Material: Glass Filled Polyester (P BT ) or High Temperature Nylon
Flammability: UL 94V-0
Color: Black
Contact
Material: Copper Alloy
Plating
Underplating: 100 μ″ [ 2.54 μm ] Nickel
Wiping Area: Gold, Tin Lead or Matte Tin (See ordering information)
Solder Tails: Tin Lead or Matte T in (See ordering information)
Marking: None
Current Rating: 1 A
Insulation Resistance: > 1 × 109Ω at 500 VDC
Withstanding Voltage: 1000 Vrms at Sea Level
Temperature Rating: -40°C to 105°C
Process Rating: 260°C (High Temp Nylon version only) single pass, (Profile per J-STD-020C)
(PBT Insulator version), Maximum molded insulator temperature 191°C (Sol-
der Wave Process Only)
• 1-36 contacts
• Tuning fork contact design
• Low profile permits boar d stacking as close
as .150″
• Solder stand-offs facilitate production wave
soldering
• See Regulatory Information Appendix (RIA)
for chemical compliance information
TS-0211-12
Sheet 1 of 2
Date Modified: March 9, 2007
UL File No.: E68080
3M
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ Boardmount Socket
.100″ Low Profile, Straight, Solder Tails 929 Series
Contact
Quantity Dimension A
02 0.20 [ 5.08 ]
03 0.30 [ 7.62 ]
04 0.40 [ 10.16 ]
05 0.50 [ 12.70 ]
06 0.60 [ 15.24 ]
07 0.70 [ 17.78 ]
08 0.80 [ 20.32 ]
09 0.90 [ 22.86 ]
10 1.00 [ 25.40 ]
11 1.10 [ 27.94 ]
12 1.20 [ 30.48 ]
13 1.30 [ 33.02 ]
14 1.40 [ 35.56 ]
15 1.50 [ 38.10 ]
16 1.60 [ 40.64 ]
17 1.70 [ 43.18 ]
18 1.80 [ 45.72 ]
19 1.90 [ 48.26 ]
20 2.00 [ 50.80 ]
21 2.10 [ 53.34 ]
22 2.20 [ 55.88 ]
23 2.30 [ 58.42 ]
24 2.40 [ 60.96 ]
25 2.50 [ 63.50 ]
26 2.60 [ 66.04 ]
27 2.70 [ 68.58 ]
28 2.80 [ 71.12 ]
29 2.90 [ 73.66 ]
30 3.00 [ 76.20 ]
31 3.10 [ 78.74 ]
32 3.20 [ 81.28 ]
33 3.30 [ 83.82 ]
34 3.40 [ 86.36 ]
35 3.50 [ 88.90 ]
36 3.60 [ 91.44 ]
TS-0211-12
Sheet 2 of 2
Ordering Information
.0 .00 .000
inch ±.1 ±.01 ±.005
[ ] D im ensions for R eference
Onl
y
Tolerance Unless Noted
[mm]
Inch
Note:
1. Maximum recommended mating header pin length is .101 [ 2.57 ].
ø.035 ± .003
[ 0.89 ]
.100 ± .003
[ 2.54 ]
Recommended Mounting Hole Pattern
(Shown for mounting side of board)
.016
[ 0.41 ] .100 Ref
[ 2.54 ]
A
A
.015
[ 0.38 ]
Section A-A
.025
[ 0.64 ]
.15
[ 3.8 ]
.P.O.M.
023 Ref
[ 0.58 ]
.125
[ 3.18 ] +.010
-.005
.100
[ 2.54 ]
A
Plating Options:
870 = Gold
984 = Tin Contact Quantity:
See Table
Plating Options:
984 Series (Tin plated)
blank = overall tin-lead (RIA E3 & C2 apply)
RK = overall matte tin (RIA E1 & C1 apply)
870 Series (Gold plated)
10 = 10µ" gold with tin-lead tail s (RIA E3 & C2 apply)
30 = 30µ" gold with tin-lead tail s (RIA E3 & C2 apply)
RA = 10µ" gold with matte tin tails (RIA E1 & C1 apply)
RB = 30µ" gold with matte tin tails (RIA E1 & C1 apply)
929XXX-01-XX-XX
Regulatory Information Appendix
3M Electronic Solutions Division/Interconnect
EUROPE
Appendix E1: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product is RoHS Compliant 2005/95/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in
excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/
EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E2: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/747/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in
excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/
EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E3: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as
amended by Commission Decision 2005/618/EC.
This product contains lead in the solder tail area in excess of the maximum concentration value allowed.
Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon
information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E4: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/17/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in
excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision
2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in
writing, this information represents 3M’s best knowledge and belief based upon information provided by third party
suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
RIA-2217-A
CHINA
Appendix C1: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits
for Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006,
means that the product or part does not contain any of the following substances in excess of the following maximum
concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium,
polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise
stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by
third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix C2: China RoHS
20
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits
for Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006,
means that the product or part does contain a substance, as detailed in the chart below, in excess of the following
maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent
chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless
otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information
provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform
with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in
accordance with the product Warranty stated below.
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the
accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended
application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s
current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in
writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of ninety (90) days from the time of purchase. 3M MAKES NO
OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s
option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for
any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.
Name and Content of Hazardous Substances or Elements
3
Electronic Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
800/225-5373
www.3M.com/interconnects RIA-2217-A
© 3M 2007
