SIL06 Series Single output DC/DC CONVERTERS * * * * * * * * * * 6A Non-isolated DC/DC Converters 1 NEW Product Ultra wide trim range 0.9V to 3.3V/5.0V Current sink capability for termination application Horizontal and vertical-mount options available High power density design means reduced board space requirement Power good output signal (open collector) Operating ambient temperature up to +80C with suitable derating and forced air cooling Remote ON/OFF (active high) 0A minimum load Input under-voltage lockout Over-current and short-circuit protection The SIL06 Series is a new high density open frame non-isolated converter for space sensitive applications. Each model has a wide input range (4.5 - 5.5VDC or 10.2 13.8VDC) and offer a wide 0.9 - 5V output voltage range with a 6A load. An external resistor adjusts the output voltage from its pre-set value of 0.9V to any value up to the 5V maximum. Typical efficiencies for the models are 89% for the 5V input version and 91% for the 12V input version. The SIL06 series offers remote ON/OFF and overcurrent protection as standard. With full international safety approval including EN60950 and UL/cUL60950, the SIL06 reduces compliance costs and time to market. 2 YEAR WARRANTY SPECIFICATIONS All specifications are typical at nominal input, full load at 25C unless otherwise stated OUTPUT SPECIFICATIONS Voltage adjustability (See Note 7) INPUT SPECIFICATIONS Contd. 5V input models 12V input models 0.9V to 3.3V 0.9V to 5.0V Output setpoint accuracy With 1.0% trim resistors 2.5% Line regulation Low line to high line 0.2% max. Load regulation Full load to min. load 0.5% max. Turn ON threshold Turn OFF threshold 5Vin model 12Vin model 5Vin model 12Vin model 4.5V 9.0V 4.3V 7.5V GENERAL SPECIFICATIONS Efficiency Min./max. load See table 0A/6A Switching frequency Overshoot (at turn on) 5V input models 12V input models 3.0% max. 1.0% max. Undershoot Ripple and noise Transient response (See Note 1) 100mV max. 5Hz to 20MHz (See Note 2) Deviation See table 75mV 150s recovery to within regulation band 5V input model 12V input model Input current No load Remote OFF Input current (max.) (See Note 9) 5V input model 12V input model 5.1A @ Io max. 1.6A @ Io max. Input reflected ripple (See Note 2) 5V input model 12V input model 52mA (pk-pk) 56mA (pk-pk) Remote ON/OFF Logic compatibility ON OFF Start-up time (See Note 3) 4.5 to 5.5VDC 10.2 to 13.8VDC 50mA 5mA Active high >2.4VDC <0.8VDC Power up Remote ON/OFF <20ms <20ms 200kHz Approvals and standards (See Note 4) TUV Product Service IEC60950, UL/cUL60950 Material flammability UL94V-0 Weight 9.3g (0.3oz) MTBF Representative model: INPUT SPECIFICATIONS Input voltage range Fixed MIL-HDBK-217F 1,307,257 hours 12V model @ 40C 100% load, ground benign Bellcore 332 7, 562,142 hours ENVIRONMENTAL SPECIFICATIONS Thermal performance (See Note 10) Altitude derating (above sea level) Operating ambient, temperature Non-operating 0C to +80C -40C to +125C 3,000m (9,843 ft) 10,000m (32,808 ft) 20% 50% International Safety Standard Approvals UL/cUL CAN/CSA 22.2 No. E139421 UL60950 file No. E139421 TUV TUV Product Service (EN60950) Certificate No. B0211 19870 205 CB report and certificate to IEC60950 File Name: SIL06.PDF Rev: 31 Jan 2003 SIL06 Series Single Output DC/DC CONVERTERS 6A Non-isolated DC/DC Converters 2 For the most current data and application support visit www.artesyn.com/powergroup/products.htm OUTPUT POWER (MAX.) INPUT VOLTAGE OVP OUTPUT OUTPUT CURRENT VOLTAGE(12) (MIN.) 20W 4.5-5.5VDC N/A 0.9V - 3.3V 30W 10.2-13.8VDC N/A 0.9V - 5.0V NEW Product OUTPUT CURRENT (MAX.) EFFICIENCY (TYP.) LINE LOAD MODEL NUMBER (5) 0A 6A 89% 0.2% 0.5% SIL06-05SADJ-V 0A 6A 91% 0.2% 0.5% SIL06-12SADJ-V Notes REGULATION Ripple and Noise Specification 1 di/dt = 10A/s, Vin = Nom, Tc = 25C, load change = 0.5 lo max. to 0.75 lo max. and 0.75 lo max. to 0.5 lo max. 2 Measured with external filter. See Application Note 131 for details. 3 Power up is the time from application of DC input to Power Good enabled. Remote ON/OFF is from ON/OFF asserted high to Power Good enabled 4 This product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. 5 The standard unit with the suffix '-V' is for vertical mounting. To order a unit with horizontal mounting, please add the suffix '-H' to the model number, e.g. SIL06-05SADJ-H. 6 Measured as per recommended set-up. Cin = 270F (20m esr max.). Cout = 680F (10m esr max.). 7 Uses external resistor from trim to output ground. Minimum value 485 for 5V model, 280 for 12V model. See Applications Note 131 for details. 8 Signal line assumed <3m. 9 External input fusing recommended. 10 See Application Note 131 for operation above 50C. 11 See Application Note 131 for more details. 12 These models have a wide trim output. 5Vin has an output of 0.9V to 3.3V and 12 Vin has an output of 0.9V to 5V. An external resistor adjusts the output voltage. PIN CONNECTIONS PIN NUMBER FUNCTION 1 Vout 2 Trim 3 Ground 4 Power Good 5 Remote ON/OFF 6 Vin 7 Mechanical support 8 Mechanical support 9 Mechanical support on horizontal version only Output Voltage Pk - Pk RMS 5V input models 0.9 to 2.5V 3.3V 30mV 40mV 15mV 15mV 12V input models 0.9 to 2.5V 3.3 to 5V 40mV 50mV 20mV 20mV Model PROTECTION Short-circuit protection Hiccup, non-latching RECOMMENDED SYSTEM CAPACITANCE Input capacitance (See Note 11) 270F/20m esr max. Output capacitance (See Note 11) 680f/10m esr max. CAUTION: High internal temperatures. Ensure that unit is not user accessible. Please consult our website for the following items: Application Note Longform Data Sheet www.artesyn.com File Name: SIL06.PDF Rev: 31 Jan 2003 SIL06 Series Single Output DC/DC CONVERTERS 6A Non-isolated DC/DC Converters 3 For the most current data and application support visit www.artesyn.com/powergroup/products.htm NEW Product 0.610 (15.49) 0.527 (13.38) 1.200 (30.48) 0.120 (3.05) 9 Places PIN 8 0.150 (3.81) Ref. 0.062 (1.57) PCB Ref. 0.315 (8.00 max.) All dimensions in INCHES (mm) General tolerance 0.01in (0.25mm) except where specified otherwise PIN 1 0.025 (0.64) Typ. 0.025 (0.64) Typ. Mechanical Support Pin Figure 1: Mechanical Drawing - Horizontal Mount Version Pin 8 Pin 1 0.025 (0.64) 0.062 (1.57) Ref. 0.150 (3.81) 8 Places 0.315 (8.00) max. 0.610 (15.49) 1.200 (30.48) 0.040 (1.02) Ref. 0.070 (1.78) All dimensions in inches (mm) General tolerance 0.01in (0.25mm) except where specified otherwise 0.050 (1.27) 0.025 (0.64) Typ. Figure 2: Mechanical Drawing - Vertical Mount Version Data Sheet (c) Artesyn Technologies(R) 2003 The information and specifications contained in this data sheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein. Please consult our website for the following items: Application Note Longform Data Sheet www.artesyn.com File Name: SIL06.PDF Rev: 31 Jan 2003