ACDC 120180 Watts SDS Series xppower.com * Convectioncooled * 3" x 5" Footprint * Up to 90% Efficiency * Open Frame, UChannel & Covered Versions * Low Temperature Option * Single & Multi Outputs * 3 Year Warranty Specification Input * 90-264 VAC (120-370 VDC) * 47-63 Hz * 120 W: 1.7 /1.0 A max at 115 /230 VAC 150 W: 2.0 /0.8 A max at 115 /230 VAC 180 W: 2.7 A max at 90 VAC Inrush Current * 120 W: 20 /51 A max at 115 /230 VAC 150 W: 54 /63 A max at 115 /230 VAC 180 W: 54 /108 A max at 115 /230 VAC Power Factor * >0.9 Earth Leakage Current * 120 W: 0.30 /0.75 mA at 115 /230 VAC 150 W: 0.40 /0.75 mA at 115 /230 VAC 180 W: 0.75 mA at 230 VAC Input Protection * Internal T3.15 A /250 VAC fuse in line No Load Input Power * 180 W: <0.5 W Input Voltage Input Frequency Input Current Output * See table * 5% output 1 only (3.3 V variant 10%) SDS180: not user adjustable Initial Set Accuracy * Single output models: 1% Multi-output models: 5% Minimum Load * No minimum load required for single output models. For multi-output models (see table) Start Up Delay * 2 s max Start Up Rise Time * 2 ms typical Hold Up Time * 16 ms minimum at full load and 110 VAC Line Regulation * 0.5% typical Load Regulation * 3.0% typical Transient Response * 4% max deviation, recovery to within 1% in 500 s for a 50% load change Ripple & Noise * 1% pk-pk typical, 20 MHz bandwidth Overvoltage Protection * 112-132% V1 only, recycle input to reset Overload Protection * All outputs: 110-150% with auto recovery (primary power limit) Short Circuit Protection * Trip & restart (hiccup mode), auto recovery Temperature * 0.04%/C Coefficient Output Voltage Output Voltage Trim General Efficiency Isolation Isolation Resistance Switching Frequency Power Density Signals MTBF * 120 W: 80% typical 150 W and 180 W: 88% typical * 3000 VAC Input to Output, 1500 VAC Input to Ground, 500 VDC Output to Ground * 50 M * 120 W: PFC 100 kHz typical, PWM 67 kHz typical. 150 W: PFC 34 kHz minimum, PWM 55 kHz typical. 180 W: PFC 67 kHz typical, PWM 67 kHz typical * 120 W: 4.87 W/In3, 150 W: 6.50 W/In3 180 W: 7.47 W/In3 * Power Fail Detect = TTL active low, combined AC and DC OK signal (-P versions SDS120 & 150 only) Warning time 16 ms * >130 kHrs to MIL-HDBK-217F at 25 C, GB Environmental Operating Temperature * 0 C to +70 C (-20 C to +70 C, SDS180), derate linearly from 100% load at +50 C to 50% load at +70 C, for low temperature option add suffix -L: -40 C to +70 C, SDS120 and SDS150, not available for SDS180 Cooling * Convection-cooled Operating Humidity * 5-95% RH, non-condensing Storage Temperature * -40 C to +85 C EMC & Safety Emissions Harmonic Currents Voltage Flicker ESD Immunity * * * * Radiated Immunity EFT/Burst Surge * * * Conducted Immunity Magnetic Field Dips & Interruptions * * * Safety Approvals * EN55022, level B conducted & radiated. EN61000-3-2 class A EN61000-3-3 EN61000-4-2, level 2 contact, Perf Criteria A SDS150: level 3 air, Perf criteria A EN61000-4-3, level 2, Perf Criteria A EN61000-4-4, level 2, Perf Criteria A EN61000-4-5, installation class 3, Perf Criteria A EN61000-4-6, level 2 , Perf Criteria A EN61000-4-8, 1 A/m, Perf Criteria A EN61000-4-11, 30% 10 ms, 60% 100 ms, >95% 5000 ms Perf Criteria A, B, B EN60950-1, UL60950-1,CSA60950-1 per cUL. Output Power 72.0 110.0 115.0 120.0 120.0 120.0 120.0 120.0 120.0 120.0 120.0 79.5 120.0 120.0 120.0 120.0 120.0 120.0 91.5 91.5 120.0 120.0 120.0 120.0 120.0 120.0 120.0 120.0 120.0 120.0 120.0 120.0 120.0 120.0 120.0 120.0 W W W W W W W W W W W W W W W W W W W W W W W W W W W W W W W W W W W W Vnom 3.3 V 5.0 V 7.0 V 9.0 V 12.0 V 15.0 V 18.0 V 24.0 V 28.0 V 36.0 V 48.0 V +3.3 V +3.3 V +5.0 V +5.0 V +5.0 V +5.0 V +28.0 V +3.3 V +3.3 V +3.3 V +3.3 V +3.3 V +3.3 V +5.0 V +5.0 V +5.0 V +5.0 V +5.0 V +5.0 V +5.0 V +5.0 V +5.0 V +5.0 V +5.0 V +5.0 V Output 1 Imin Imax 0.00 A 22.00 A 0.00 A 22.00 A 0.00 A 16.42 A 0.00 A 13.33 A 0.00 A 10.00 A 0.00 A 8.00 A 0.00 A 6.66 A 0.00 A 5.00 A 0.00 A 4.28 A 0.00 A 3.33 A 0.00 A 2.50 A 1.50 A 15.00 A 1.50 A 15.00 A 1.50 A 15.00 A 1.50 A 15.00 A 1.50 A 15.00 A 1.50 A 15.00 A 0.39 A 3.92 A 1.50 A 15.00 A 1.50 A 15.00 A 1.50 A 15.00 A 1.50 A 15.00 A 1.50 A 15.00 A 1.50 A 15.00 A 1.50 A 15.00 A 1.50 A 15.00 A 1.50 A 15.00 A 1.50 A 15.00 A 1.50 A 15.00 A 1.50 A 15.00 A 1.50 A 15.00 A 1.50 A 15.00 A 1.50 A 15.00 A 1.50 A 15.00 A 1.50 A 15.00 A 1.50 A 15.00 A Tol.(1) 5% 5% 5% 4% 3% 3% 3% 2% 2% 2% 2% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% Output 2 Imin Imax Vnom +5.0 +12.0 +12.0 +15.0 +24.0 -24.0 +5.0 +5.0 +5.0 +12.0 +12.0 +12.0 +12.0 +12.0 +12.0 +12.0 +12.0 +15.0 +15.0 +24.0 +24.0 +24.0 +24.0 +10.0 +10.0 V V V V V V V V V V V V V V V V V V V V V V V V V 0.40 0.20 0.20 0.20 0.10 0.20 0.20 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.60 0.35 0.35 0.35 0.35 0.60 0.60 A A A A A A A A A A A A A A A A A A A A A A A A A 6.0 6.0 6.0 6.0 3.5 2.0 2.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 3.5 3.5 3.5 3.5 6.0 6.0 A A A A A A A A A A A A A A A A A A A A A A A A A Tol.(1) 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% Vnom +12.0 -12.0 +5.0 -5.0 -12.0 +12.0 +5.0 -5.0 -12.0 +12.0 -15.0 +15.0 -24.0 +24.0 -12.0 +12.0 -10.0 +10.0 V V V V V V V V V V V V V V V V V V Output 3 Imin Imax 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 A A A A A A A A A A A A A A A A A A 1.0 1.0 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 1.0 1.0 Tol.(1) A A A A A A A A A A A A A A A A A A 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% Model Number(2, 4, 5) SDS120PS03B SDS120PS05B SDS120PS07B SDS120PS09B SDS120PS12B SDS120PS15B SDS120PS18B SDS120PS24B SDS120PS28B SDS120PS36B SDS120PS48B SDS120PD00B SDS120PD01B SDS120PD02B SDS120PD03B SDS120PD04B SDS120PD05B SDS120PD06B SDS120PT00B SDS120PT01B SDS120PT02B SDS120PT03B SDS120PT04B SDS120PT05B SDS120PT06B SDS120PT07B SDS120PT08B SDS120PT09B SDS120PT10B SDS120PT11B SDS120PT12B SDS120PT13B SDS120PT14B SDS120PT15B SDS120PT16B SDS120PT17B Notes 1. Tol. (total regulation) includes line regulation and load regulation. 2. For optional PCB only version, delete suffix `B' from model number. Example SDS120PS03. 3. For non-standard voltages contact sales. 4. For optional low temperature -40 C operation, add suffix `-L' to model number. Example: SDS120PS12B-L 5. For optional Power Fail Detect circuit, add suffix `-P' to model number, example: SDS120PS12B-P Mechanical Details 1.18 (30.0) 0.25 (6.4) 4.49 (114.3) 0.32 (8.1) M3XP0.5 (Mounting Holes) X 4 V Adj. DC OUTPUT AC P1 INPUT L 1.54 (39.2) P2 1 2.57 (65.3) N G 3.20 (81.4) PIN CONNECTIONS Single Dual Triple V1 V2 V2 V1 V2 V2 V1 V1 V1 V1 V1 V1 V1 V1 V1 V1 V1 V1 Return Common Common Return Common Common Return Common Common Return N/C V3 Return Common Common Return Common Common PFD(1) PFD(1) PFD(1) Power Fail Detect (PFD) is +5 V for normal operation. +5 V Source current is 5 mA max. Pin 13 PFD is <0.4 V for either AC Fail (<90 VAC) or DC Fail (<95% Vnom). Sink current is 10 mA max. Internal Notes 2.70 (68.6) 0.55 (14.0) 5.00 (127.0) 4.49 (114.3) 4.00 (101.6) M3xP0.5 (Mounting Holes) X 3 0.25 (6.4) 1.18 (30.0) 3.01+0.20 0.00 (76.4 +0.5 0.0) 3.20+0.20 0.01 (81.4 +0.5 -0.2) 0.10 (2.5) Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 1. 2. 3. 4. Optional Power Fail Detect signal on `-P' versions only. Standard models pin 13 is N/C. I/P connector P1 mates with Molex housing 09-50-3051 & Molex 2878 series crimp terminal. O/P P2 mates with Molex housing 09-50-3131 & Molex 2878 series crimp terminal. For optional cover kit order part number SDS120 COVER, to receive unit with cover fitted add suffix `-C' to model number, e.g. SDS120PS12B-C (overall height is 1.73 (44.0)). 5. For mating connector kit order part number SDS120/SDS150 CON KIT. 6. For cable harness order part number SDS120S LOOM for single output models & SDS120M LOOM for multi-output models. 7. Maximum mounting screw penetration: 0.14 (3.5) 8. All dimensions are in inches (mm). 9. Weight: 0.77-0.99 lbs (350-450 g) approx. 10. For PCB-only version, overall dimensions are max 5.00 x 3.00 x 1.44 (127.0 x 76.2 x 36.6). ACDC SDS120 Models and Ratings Output Power 144 150 150 150 150 150 150 150 Output Current Output Voltage W W W W W W W W 9 12 15 18 24 30 36 48 Minimum 0A 0A 0A 0A 0A 0A 0A 0A V V V V V V V V Total Regulation(1) Maximum 16.00 A 12.50 A 10.00 A 8.33 A 6.25 A 5.00 A 4.17 A 3.13 A 5% 5% 5% 4% 3% 2% 2% 2% Model Number(2,4,5,6) SDS150PS09B SDS150PS12B SDS150PS15B SDS150PS18B SDS150PS24B SDS150PS30B SDS150PS36B SDS150PS48B Notes 1. Total regulation includes line regulation and load regulation. 2. For optional 2 pin Molex input, add suffix `-D' to model number. Example SDS150PS12B-D. 3. For non-standard voltages contact sales. 4. For optional low temperature -40 C operation, add suffix `-L' to model number. Example: SDS150PS12B-L 5. For optional PCB only version, delete suffix `B' from model number. Example SDS150PS48. 6. For optional Power Fail Detect signal (PFD), add suffix `-P' to model number. Example: SDS150PS48B-P. Mechanical Details U Channel 0.30 (7.7) M3* P0.5 (Mounting Holes) x 5 0.54 (13.6) 1.18 (30.0) AC Input G N 1.18 (30.0) L P1 4.00 (101.6) 4.50 (114.3) 5.00 (127.0) 4.50 (114.3) 13 2.57 (65.3) 1 P2 Pitch = 3.96 mm M3* P0.5 (Mounting Holes) x 4 0.25 (6.4) 0.67 (16.9) 1.62 (41.2) 0.55 (14.0) DC Output Voltage Adj. 3.21 (81.5) 1.16 (29.6) Open Frame M3 x P0.5 (Mounting Holes) x 4 1.57 (40.0) Notes 1. All dimensions in inches (mm), tolerance 0.02 (0.5). 2. Input connector P1 mates with Molex housing 09-50-3051 and Molex 2478 series crimp terminal. 3. Output connector P2 mates with Molex housing 09-50-3131 and Molex 2478 series crimp terminal. 4. Optional power fail detect signal on `-P' versions only. Standard models pin 13 is not connected. 5. For mating connector kit order part number SDS120/SDS150 CON KIT. 6. For cable harness order part number SDS150 LOOM. 7. Maximum mounting screw penetration: 0.14 (3.5) 8. For optional cover kit order part number SDS150 COVER 9. Weight: U Channel - 1.27 lbs (580 g) approx. Open Frame - 0.86 lbs (390 g) approx. 0.22 (5.7) 4.55 (115.6) Voltage Adj. 0.56 (14.2) +5 V 5.00 (127.0) 1.40 (35.6) Pitch = 3.96 mm N 13 Internal P1 0.12 (3.0) 0.80 (20.3) 1.16 (29.6) 1.21 (30.7) Source current is 5 mA max. PFD is <0.4 V for either AC Fail (<90 VAC) or DC Fail (<95% Vnom). Sink current is 10 mA max. 3.00 (76.2) 0.32 (7.9) L G 0.43 (10.9) 2.57 (65.3) DC Output Power Fail Detect (PFD) is +5 V for normal operation. Pin 13 P2 1 AC Input Function Return Return Return Return Return Return PFD(4) 0.80 (20.3) o4.0 (Mounting Holes) x 4 0.22 (5.5) P2 - PIN CONNECTIONS Function Pin V1 7 V1 8 V1 9 V1 10 V1 11 V1 12 13 Pin 1 2 3 4 5 6 0.25 (6.4) 3.90 (99.0) 3.00 (76.2) ACDC SDS150 Models and Ratings Output Power Output Voltage 170 W 180 W 180 W 12 V 24 V 48 V (1) Output Current Minimum 0A 0A 0A Maximum 14.16 A 7.50 A 3.75 A Total Regulation(2) Model Number(3) 5% 3% 2% SDS180PS12B SDS180PS24B SDS180PS48B Notes 1. Output power is 170 W at highline input and 160 W at low line input, (90-132 VAC). 2. Total regulation includes line regulation and load regulation. 3. For optional L-bracket version, delete suffix `B' from model number. Example SDS180PS48. 4. For non-standard voltages contact sales. Mechanical Details U Channel For 12 V Version Only 25.6 +0.5 Pitch=7.62 mm DC Output 4 3.21 (81.6) 0.55 (14.0) 0.30 (7.7) 1.10 (28.0) 0.25 (6.4) 0.85 (21.6) Pitch=3.96mm P2 1 0.25 (6.4) 1.10 (28.0) 8 LED 2.57 (65.3) 3.90 (99.1) Pin 1 2 3 4 P2 - PIN CONNECTIONS 24/48 V versions Function Pin Function Return 5 V1 Return 6 V1 Return 7 V1 Return 8 V1 Pin 1 2 PIN CONNECTIONS 12 V version Function Pin Function Return 3 V1 Return 4 V1 4.00 (101.6) 4.50 (114.3) 5.00 (127.0) 4.50 (114.3) P1 L M3 x P0.5 (Mounting Holes) x 4 1.54 (39.2) N AC Input 2.18 (55.4) M3 x P0.5 (Mounting Holes) x 2 M3 x P0.5 (Mounting Holes) x 3 For 12 V Version Only 25.6 +0.5 Pitch=7.62 mm DC Output Lbracket 3.13 (79.6) 2.57 (65.3) 0.30 (7.7) 1.10 (28.0) 0.25 (6.4) 0.85 (21.6)1 Pitch=3.96mm P2 8 LED 0.55 (14.0) 4 5.00 (127.0) 4.50 (114.3) 3.90 (99.1) Notes 1. All dimensions in inches (mm), tolerance 0.02 (0.5). 2. Input connector P1 mates with Molex housing 09-50-3031 and Molex 2478 series crimp terminal. 3. Output connector P2 mates with Molex housing 09-50-3061 (or 09-50-3081) and Molex 2478 series crimp terminal for 24/48 V Versions. For 12 V Version, output terminal is screw terminal. 4. For mating connector kit order part number: SDS180 CON KIT. 5. For cable harness order part number SDS180 LOOM. 6. Maximum mounting screw penetration: 0.14 (3.5) 7. Weight: U Channel - 1.14 lbs (520 g) L-bracket - 1.06 lbs (480 g) P1 L M3 x P0.5 (Mounting Holes) x 4 1.54 (39.2) 2.18 (55.4) N AC Input M3 x P0.5 (Mounting Holes) x 2 17-Dec-13 ACDC SDS180 Models and Ratings