General Purpose
Industrial VRS Magnetic
Speed Sensors
DESCRIPTION
General Purpose VRS sensors are designed for use in
applications with medium to high speeds or in electrically noisy
environments with relatively small air gaps.
Passive VRS (Variable Reluctance Speed) Magnetic Speed
sensors are simple, rugged devices that do not require an
external voltage source for operation.
A permanent magnet in the sensor establishes a fixed
magnetic field. The approach and passing of a ferrous metal
target near the sensor’s pole piece (sensing area) cha nges the
flux of the magnetic field, dynamically changing its strength.
This change in magnetic field strength induces a current into a
coil winding which is attached to the output terminals.
The output signal of a VRS sensor is an ac voltage that varies
in amplitude and wave frequency as the speed of the
monitored device changes, and is usually expressed in peak to
peak voltage (Vp-p).
One complete waveform (cycle) occurs as each target passes
the sensor’s pole piece. If a standard gear were used as a
target, this output signal would resemble a sine wave if viewed
on an oscilloscope.
Honeywell also offers VRS sensors for high output, power
output, high resolution, high temperature and hazardous
location applications, as well as low-cost molded versions.
FEATURES
Self-powered operation
Direct conversion of actuator speed to output frequency
Simple installation
No moving parts
Designed for use over a wide range of speeds
Adaptable to a wide variety of configurations
Customized VRS products for unique speed sensing
applications
Housing diameters: 5/8 in (M16), 3/8 in (M12) mm,
1/4 in (M8), 10/32 in
Housing materials/styles: stainless steel threaded or
smooth
Terminations: MS3106 connector, preleaded
Output voltages: 8 Vp-p to 40 Vp-p
POTENTIAL APPLICATIONS
Engine RPM (revolutions per minute) measurement on
aircraft, automobiles, boats, buses, trucks and rail
vehicles
Motor RPM measurement on drills, grinders, lathes and
automatic screw ma chi nes
Motor RPM measurement on precision camera, tape
recording and motion picture equipment
Process speed measurement on food, textile, paper,
woodworking, printing, tobacco and pharmaceutical
industry machinery
Motor speed measurement of electrical generating
equipment
Speed measurement of pumps, blowers, mixers, exhaust
and ventilat ing fans
Flow measurement on turbine meters
Wheel-sl ip mea surem en t on autos and lo com oti ves
Gear speed measurement
General Purpose
2 www.honeywell.com/sensing
5/8 INCH (M16*) SENSORS (All dimensions for reference only. mm/[in])
*Contact Honeywell for availability of metric mounting thread versions.
General Specifications Test Condition Specifications
Parameter Characteristic Parameter Characteristic Parameter Characteristic
Min. output voltage 40 Vp-p Inductance 25 mH max. Surface speed 25 m/s
[1000 in/s]
Coil resistance 45 Ohm to 85 Ohm Gear pitch range 24 DP (module 1.06)
or coarser Gear 20 DP
(module 1.27)
Pole piece
diameter 2,69 mm [0.106 in] Optimum actuator 20 DP (module 1.27)
ferrous metal gear Air gap 0,127 mm
[0.005 in]
Min. surface
speed 0,50 m/s [20 in/s] typ. Max. operating
frequency 50 kHz typ.
Operating temp.
range -55 ºC to 120 ºC
[-67 ºF to 250 ºF] Vibration Mil-Std 202F
Method 204D
Mounting thread 5/8-18 UNF-2A Termination MS3106 connector
Load
resistance 100 kOhm
Catalog
Listing Thread
Length (A) Weight
3010AN
3010AN25
3010AN30
3010AN40
3010AN50
28 mm [1.1 in]
63 mm [2.5 in]
76 mm [3.0 in]
101 mm [4.0 in]
127 mm [5.0 in]
70 g [2.5 oz]
84 g [3.0 oz]
84 g [3.0 oz]
98 g [3.5 oz]
128 g [4.5 oz]
Catalog
Listing Thread
Length (A) Weight
3010A
3010A25
35 mm [1.4 in]
63 mm [2.5 in] 70 g [2.5 oz]
84 g [3.0 oz]
Industrial VRS Magnetic Speed Sensors
Honeywell Sensi ng and Control 3
5/8 INCH (M16*) SENSORS CONTINUED (All dimensions for reference only. mm/[in])
*Contact Honeywell for availability of metric mounting thread versions.
General Specifications Test Condition Specifications
Parameter Characteristic Parameter Characteristic Parameter Characteristic
Min. output voltage 40 Vp-p Inductance 25 mH max. Surface speed 25 m/s
[1000 in/s]
Coil resistance 45 Ohm to 85 Ohm Gear pitch range 24 DP (module 1.06)
or coarser Gear 20 DP
(module 1.27)
Pole piece
diameter 2,69 mm [0.106 in] Optimum actuator 20 DP (module 1.27)
ferrous metal gear Air gap 0,127 mm
[0.005 in]
Min. surface
speed 0,50 m/s [20 in/s] typ. Max. operating
frequency 50 kHz typ.
Operating temp.
range -55 ºC to 120 ºC
[-67 ºF to 250 ºF] Vibration Mil-Std 202F
Method 204D
Mounting thread 5/8-18 UNF-2A Termination 20 AWG Teflon-
insulated leads
Load
resistance 100 kOhm
Catalog
Listing Weight
3010H20
140 g [5.0 oz]
Catalog
Listing Thread
Length (A) Weight
3010S20
3010S30
50 mm [2.0 in]
76 mm [3.0 in] 70 g [2.5 oz]
84 g [3.0 oz]
General Purpose
4 www.honeywell.com/sensing
3/8 INCH (M12*) SENSORS
*Contact Honeywell for availability of metric mounting thread versions.
General Specifications Test Condition Specifications
Parameter Characteristic Parameter Characteristic Parameter Characteristic
Min. output
voltage 20 Vp-p Inductance 15 mH max. Surface speed 25 m/s
[1000 in/s]
Coil resistance 45 Ohm to 65 Ohm Gear pitch range 26 DP (module 0.98)
or coarser Gear 20 DP
(module 1.27)
Pole piece
diameter 2,36 mm [0.093 in] Optimum actuator 24 DP (module 1.06)
ferrous metal gear Air gap 0,127 mm
[0.005 in]
Min. surface
speed 0,50 m/s [20 in/s] typ. Max. operating
frequency 50 kHz typ.
Operating temp.
range -40 ºC to 107 ºC
[-40 ºF to 225 ºF] Vibration Mil-Std 202F
Method 204D
Mounting thread 3/8-24 UNF-2A Termination 24 AWG vinyl-insulated
leads
Load
resistance 100 kOhm
Catalog
Listing Thread
Length (A) Weight
3015A
3015A17
3015A35
20 mm [0.8 in]
44 mm [1.7 in]
88 mm [3.5 in]
28 g [1.0 oz]
35 g [1.2 oz]
42 g [1.5 oz]
Catalog
Listing Weight
3015S13 28 g [1.0 oz]
Catalog
Listing Thread
Length (A) Weight
3015SS13
3015SS25
30 mm [1.2 in]
63 mm [2.5 in]
28 g [1.0 oz]
42 g [152 oz]
Industrial VRS Magnetic Speed Sensors
Honeywell Sensi ng and Control 5
1/4 INCH (M8*) SENSORS (All dimensions for reference only. mm/[in])
*Contact Honeywell for availability of metric mounting thread versions.
General Specifications Test Condition Specifications
Parameter Characteristic Parameter Characteristic Parameter Characteristic
Min. output
voltage 12 Vp-p Inductance 16 mH max. Surface speed 25 m/s
[1000 in/s]
Coil resistance 190 Ohm max. Gear pitch range 36 DP (module 0.70)
or coarser Gear 20 DP
(module 1.27)
Pole piece
diameter 1,00 mm [0.040 in] Optimum actuator 28 DP (module 0.90)
ferrous metal gear Air gap 0,127 mm
[0.005 in]
Min.
surface speed 0,75 m/s [30 in/s] typ. Max. operating
frequency 60 kHz typ.
Operating temp.
range -40 ºC to 107 ºC
[-40 ºF to 225 ºF] Vibration Mil-Std 202F
Method 204D
Mounting thread 1/4-40 UNS-2A Termination 30 AWG vinyl-insulated
leads
Load
resistance 100 kOhm
Catalog
Listing Thread
Length (A) Weight
3050
3050A13
3050A20
15 mm [0.6 in]
30 mm [1.2 in]
50 mm [2.0 in]
14 g [0.5 oz]
14 g [0.5 oz]
14 g [0.5 oz]
Parameter Characteristic Parameter Characteristic Parameter Characteristic
Min. output
voltage 12 Vp-p Inductance 16 mH max. Surface speed 25 m/s
[1000 in/s]
Coil resistance 190 Ohm max. Gear pitch range 36 DP (module 0.70)
or coarser Gear 20 DP
(module 1.27)
Pole piece
diameter 1,00 mm [0.040 in] Optimum actuator 28 DP (module 0.90)
ferrous metal gear Air gap 0,127 mm
[0.005 in]
Min.
surface speed 0,75 m/s [30 in/s] typ. Max. operating
frequency 60 kHz typ.
Operating temp.
range -40 ºC to 107 ºC
[-40 ºF to 225 ºF] Vibration Mil-Std 202F
Method 204D
Mounting thread 1/4-40 UNS-2A Termination 30 AWG PVC-insulated
leads
Load
resistance 100 kOhm
Catalog
Listing Thread
Length Weight
3050S10 25 mm [1.0 in] 14 g [0.5 oz]
General Purpose
6 www.honeywell.com/sensing
10/32 INCH SENSORS (All dimensions for reference only. mm/[in])
(No metric available.)
General Specifications Test Condition Specifications
Parameter Characteristic Parameter Characteristic Parameter Characteristic
Min. output
voltage 8 Vp-p Inductance 14 mH max. Surface speed 25 m/s
[1000 in/s]
Coil resistance 155 Ohm Gear pitch range 32 DP (module 0.80)
or coarser Gear 20 DP
(module 1.27)
Pole piece
diameter 1,5 mm [0.062 in] Optimum actuator 26 DP (module 0.98)
ferrous metal gear Air gap 0,127 mm
[0.005 in]
Min. surface
speed 0,75 m/s [30 in/s] typ. Max. operating
frequency 60 kHz (typ.)
Operating temp.
range -40 ºC to 107 ºC
[-40 ºF to 225 ºF] Vibration Mil-Std 202F
Method 204D
Mounting thread 10-32 UNF-2A Termination 32 AWG Teflon-
insulated leads
Load
resistance 100 kOhm
Catalog
Listing Thread
Length Weight
3080 12 mm [0.5 in] 8,5 g [0.3 oz]
Industrial VRS Magnetic Speed Sensors
Honeywell Sensi ng and Control 7
THIS PAGE INTENTIONALLY LEFT BLANK.
Automation and Control Solutions
Sensing and Control
Honeywell
1985 Douglas Drive North
Minneapolis, MN 55422
www.honeywell.com/sensing
005875-2-EN IL50 GLO Printed in USA
November 2007
Copyright © 2007 Honeywell International Inc. All rights reserved.
WARNING
PERSONAL INJURY
DO NOT USE these products as safety or emergency stop
devices or in any other application where failure of the
product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARRANTY/REMEDY
Honeywell warrants goods of its manufacture as being free of
defective materials and faulty workmanship. Honeywell’s
standard product warranty applies unless agreed to otherwise
by Honeywell in writing; please refer to your order
acknowledgement or consult your local sales office for specific
warranty details. If warranted goods are returned to Honeywell
during the period of coverage, Honeywell will repair or replace,
at its option, without charge those items it finds defective. The
foregoing is buyer’s sole remedy and is in lieu of all other
warranties, expressed or implied, including those of
merchantability and fitness for a particular purpose. In no
event shall Honeywell be liable for consequential, special,
or indirect damages.
While we provide application assistance personally, through
our literature and the Honeywell web site, it is up to the
customer to determine the suitability of the product in the
application.
Specifications may change without notice. The information we
supply is believed to be accurate and reliable as of this
printing. However, we assume no responsibility for its use.
WARNING
MISUSE OF DOCUMENTATION
The information presented in this product sheet is for
reference only. Do not use this docum ent as a product
installation guide.
Complete installation, operation, and maintenance
information is provided in the instructions supplied with
each product.
Failure to comply with these instructions could result in
death or serious injury.
SALES AND SERVICE
Honeywell serves its customers through a worldwide network
of sales offices, representatives and distributors. For
application assistance, current specifications, pricing or name
of the nearest Authorized Distributor, contact your local sales
office or:
E-mail: info.sc@honeywell.com
Internet: www.honeywell.com/sensing
Phone and Fax:
Asia Pacific +65 6355-2828
+65 6445-3033 Fax
Europe +44 (0) 1698 481481
+44 (0) 1698 481676 Fax
Latin Amer ica +1-305-805-8188
+1-305-883-8257 Fax
USA/Canada +1-800-537-6945
+1-815-235-6847
+1-815-235-6545 Fax