DS1822Z+T&R - Hytronics - Datasheet.Live

AVAILABLE

Functional Diagrams

Pin Configurations appear at end of data sheet.

Functional Diagrams continued at end of data sheet.

UCSP is a trademark of Maxim Integrated Products, Inc.

For pricing, delivery, and ordering information, please contact Maxim Direct

at 1-888-629-4642, or visit Maxim’s website at www.maximintegrated.com.

FEATURES

 Unique 1-Wire® interface requires only one

port pin for communication.

 Each device has a unique 64-bit serial code

stored in an on-board ROM.

 Multidrop capability simplifies distributed

temperature-sensing applications.

 Requires no external components.

 Can be powered from data line. Power supply

range is 3.0V to 5.5V.

 Measures temperatures from -55°C to +125°C

(-67°F to +257°F).

 ±2.0°C accuracy from -10°C to +85°C.

 Thermometer resolution is user-selectable

from 9 to 12 bits.

 Converts temperature to 12-bit digital word in

750ms (max.)

 User-definable nonvolatile (NV) alarm

settings.

 Alarm search command identifies and

addresses devices whose temperature is

outside of programmed limits (temperature

alarm condition).

 Software compatible with the DS18B20.

 Applications include thermostatic controls,

industrial systems, consumer products,

thermometers, or any thermally sensitive

system.

PIN ASSIGNMENT

PIN DESCRIPTION

GND - Ground

DQ - Data In/Out

VDD - Power Supply Voltage

NC - No Connect

DESCRIPTION

The DS1822 digital thermometer provides 9- to 12-bit centigrade temperature measurements and has an

alarm function with NV user-programmable upper and lower trigger points. The DS1822 communicates

over a 1-Wire bus that by definition requires only one data line (and ground) for communication with a

central microprocessor. It has an operating temperature range of –55°C to +125°C and is accurate to

±2.0°C over the range of –10°C to +85°C. In addition, the DS1822 can derive power directly from the

data line (“parasite power”), eliminating the need for an external power supply.

Each DS1822 has a unique 64-bit serial code, which allows multiple DS1822s to function on the 1-Wire

bus; thus, it is simple to use one microprocessor to control many DS1822s distributed over a large area.

Applications that can benefit from this feature include HVAC environmental controls, temperature

monitoring systems inside buildings, equipment or machinery, and process monitoring and control

systems.

(

BOTTOM VIEW

)

2 3

Econo 1-Wire Digital

Thermomete

8-Pin 150mil SO

(DS1822Z)

TO-92

(

DS1822

)

DALLAS

1822

GND

VDD

2 3

GND

VDD

DS1822

1-Wire is a registered trademark of Dallas Semiconductor.

DS1822

101107

DS1822

2 of 21

ORDER INFORMATION

ORDERING

NUMBER

PACKAGE

MARKING

DESCRIPTION

DS1822 1822 DS1822 in 3-pin TO92

DS1822/T&R 1822 DS1822 in 3-pin TO92, 2000 Piece Tape-and-Reel

DS1822+ 1822 (See Note) DS1822 in Lead-Free 3-pin TO92

DS1822+T&R 1822 (See Note) DS1822 in Lead-Free 3-pin TO92, 2000 Piece Tape-and-

Reel

DS1822Z DS1822 DS1822 in 150 mil 8-pin SO

DS1822Z/T&R DS1822 DS1822 in 150 mil 8-pin SO, 2500 Piece Tape-and-Reel

DS1822Z+ DS1822 (See Note) DS1822 in Lead-Free 150 mil 8-pin SO

DS1822Z+T&R DS1822 (See Note) DS1822 in Lead-Free 150 mil 8-pin SO, 2500 Piece

Tape-and-Reel

Note: A “+” symbol will also be marked on the package.

DETAILED PIN DESCRIPTIONS Table 1

8-PIN SO* TO-92 SYMBOL DESCRIPTION

5 1 GND

Ground.

4 2 DQ

Data Input/Output pin. Open-drain 1-Wire interface pin. Also

provides power to the device when used in parasite power mode

(see “Parasite Power” section).

3 3 VDD Optional VDD pin. VDD must be grounded for operation in

parasite power mode.

*All pins not specified in this table are “No Connect” pins.

OVERVIEW

Figure 1 shows a block diagram of the DS1822, and pin descriptions are given in Table 1. The 64-bit

ROM stores the device’s unique serial code. The scratchpad memory contains the 2-byte temperature

access to the 1-byte upper and lower alarm trigger registers (TH and TL), and the 1-byte configuration

conversion to 9, 10, 11, or 12 bits. The TH, TL and configuration registers are NV (EEPROM), so they will

retain data when the device is powered down.

The DS1822 uses Dallas’ exclusive 1-Wire bus protocol that implements bus communication using one

control signal. The control line requires a weak pullup resistor since all devices are linked to the bus via a

3-state or open-drain port (the DQ pin in the case of the DS1822). In this bus system, the microprocessor

(the master device) identifies and addresses devices on the bus using each device’s unique 64-bit code.

Because each device has a unique code, the number of devices that can be addressed on one bus is

virtually unlimited. The 1-Wire bus protocol, including detailed explanations of the commands and “time

slots,” is covered in the 1-WIRE BUS SYSTEM section of this data sheet.

Another feature of the DS1822 is the ability to operate without an external power supply. Power is instead

supplied through the 1-Wire pullup resistor via the DQ pin when the bus is high. The high bus signal also

charges an internal capacitor (CPP), which then supplies power to the device when the bus is low. This

method of deriving power from the 1-Wire bus is referred to as “parasite power.” As an alternative, the

DS1822 may also be powered by an external supply on VDD.

DS1822

3 of 21

DS1822 BLOCK DIAGRAM Figure 1

VPU

4.7K

POWER

SUPPLY

SENSE

64-BIT ROM

AND

1-wire PORT

INTERNAL VDD

CPP

PARASITE POWER

CIRCUIT MEMORY CONTROL

LOGIC

SCRATCHPAD

8-BIT CRC GENERATOR

TEMPERATURE SENSOR

ALARM HIGH TRIGGER (TH)

ALARM LOW TRIGGER (TL)

CONFIGURATION REGISTER

(EEPROM)

GND

DS1822

4 of 21

OPERATION—MEASURING TEMPERATURE

The core functionality of the DS1822 is its direct-to-digital temperature sensor. The resolution of the

temperature sensor is user-configurable to 9, 10, 11, or 12 bits, corresponding to increments of 0.5°C,

0.25°C, 0.125°C, and 0.0625°C, respectively. The default resolution at power-up is 12 bit. The DS1822

powers-up in a low-power idle state; to initiate a temperature measurement and A-to-D conversion, the

master must issue a Convert T [44h] command. Following the conversion, the resulting thermal data is

stored in the 2-byte temperature register in the scratchpad memory and the DS1822 returns to its idle

state. If the DS1822 is powered by an external supply, the master can issue “read-time slots” (see the 1-

WIRE BUS SYSTEM section) after the Convert T command and the DS1822 will respond by

transmitting 0 while the temperature conversion is in progress and 1 when the conversion is done. If the

DS1822 is powered with parasite power, this notification technique cannot be used since the bus must be

pulled high by a strong pullup during the entire temperature conversion. The bus requirements for parasite

power are explained in detail in the POWERING THE DS1822 section of this data sheet.

The DS1822 output temperature data is calibrated in degrees centigrade; for Fahrenheit applications, a

lookup table or conversion routine must be used. The temperature data is stored as a 16-bit sign-extended

two’s complement number in the temperature register (see Figure 2). The sign bits (S) indicate if the

temperature is positive or negative: for positive numbers S = 0 and for negative numbers S = 1. If the

DS1822 is configured for 12-bit resolution, all bits in the temperature register will contain valid data. For

11-bit resolution, bit 0 is undefined. For 10-bit resolution, bits 1 and 0 are undefined, and for 9-bit

resolution bits 2, 1 and 0 are undefined. Table 2 gives examples of digital output data and the

corresponding temperature reading for 12-bit resolution conversions.

TEMPERATURE REGISTER FORMAT Figure 2

bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0

LS Byte 23 2

2 2

1 2

0 2

-1 2

-2 2

-3 2

-4

bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8

MS Byte S S S S S 26 2

5 2

TEMPERATURE/DATA RELATIONSHIP Table 2

TEMPERATURE DIGITAL OUTPUT

(Binary)

DIGITAL OUTPUT

(Hex)

+125°C 0000 0111 1101 0000 07D0h

+85°C* 0000 0101 0101 0000 0550h

+25.0625°C 0000 0001 1001 0001 0191h

+10.125°C 0000 0000 1010 0010 00A2h

+0.5°C 0000 0000 0000 1000 0008h

0°C 0000 0000 0000 0000 0000h

-0.5°C 1111 1111 1111 1000 FFF8h

-10.125°C 1111 1111 0101 1110 FF5Eh

-25.0625°C 1111 1110 0110 1111 FE6Fh

-55°C 1111 1100 1001 0000 FC90h

*The power on reset value of the temperature register is +85°C

DS1822

5 of 21

OPERATION—ALARM SIGNALING

After the DS1822 performs a temperature conversion, the temperature value is compared to the user-

defined two’s complement alarm trigger values stored in the 1-byte TH and TL registers (see Figure 3).

The sign bit (S) indicates if the value is positive or negative: for positive numbers S = 0 and for negative

numbers S = 1. The TH and TL registers are NV (EEPROM) so they will retain data when the device is

powered down. TH and TL can be accessed through bytes 2 and 3 of the scratchpad as explained in the

MEMORY section of this data sheet.

TH AND TL REGISTER FORMAT Figure 3

bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0

S 26 2

5 2

4 2

3 2

2 2

1 2

Only bits 11 through 4 of the temperature register are used in the TH and TL comparison since TH and TL

are 8-bit registers. If the measured temperature is lower than or equal to TL or higher than or equal to TH,

an alarm condition exists and an alarm flag is set inside the DS1822. This flag is updated after every

temperature measurement; therefore, if the alarm condition goes away, the flag will be turned off after the

next temperature conversion.

The master device can check the alarm flag status of all DS1822s on the bus by issuing an Alarm Search

[ECh] command. Any DS1822s with a set alarm flag will respond to the command, so the master can

determine exactly which DS1822s have experienced an alarm condition. If an alarm condition exists and

the TH or TL settings have changed, another temperature conversion should be done to validate the alarm

condition.

POWERING THE DS1822

The DS1822 can be powered by an external supply on the VDD pin, or it can operate in “parasite power”

mode, which allows the DS1822 to function without a local external supply. Parasite power is very useful

for applications that require remote temperature sensing or that are very space constrained. Figure 1

shows the DS1822’s parasite-power control circuitry, which “steals” power from the 1-Wire bus via the

DQ pin when the bus is high. The stolen charge powers the DS1822 while the bus is high, and some of

the charge is stored on the parasite power capacitor (CPP) to provide power when the bus is low. When the

DS1822 is used in parasite power mode, the VDD pin must be connected to ground.

In parasite power mode, the 1-Wire bus and CPP can provide sufficient current to the DS1822 for most

operations as long as the specified timing and voltage requirements are met (refer to the DC

ELECTRICAL CHARACTERISTICS and the AC ELECTRICAL CHARACTERISTICS sections of this

data sheet). However, when the DS1822 is performing temperature conversions or copying data from the

scratchpad memory to EEPROM, the operating current can be as high as 1.5mA. This current can cause

an unacceptable voltage drop across the weak 1-Wire pullup resistor and is more current than can be

supplied by CPP. To assure that the DS1822 has sufficient supply current, it is necessary to provide a

strong pullup on the 1-Wire bus whenever temperature conversions are taking place or data is being

copied from the scratchpad to EEPROM. This can be accomplished by using a MOSFET to pull the bus

directly to the rail as shown in Figure 4. The 1-Wire bus must be switched to the strong pullup within

10μs (max) after a Convert T [44h] or Copy Scratchpad [48h] command is issued, and the bus must be

held high by the pullup for the duration of the conversion (tconv) or data transfer (twr = 10ms). No other

activity can take place on the 1-Wire bus while the pullup is enabled.

The DS1822 can also be powered by the conventional method of connecting an external power supply to

the VDD pin, as shown in Figure 5. The advantage of this method is that the MOSFET pullup is not

required, and the 1-Wire bus is free to carry other traffic during the temperature conversion time.

DS1822

6 of 21

The use of parasite power is not recommended for temperatures above 100°C since the DS1822 may not

be able to sustain communications due to the higher leakage currents that can exist at these temperatures.

For applications in which such temperatures are likely, it is strongly recommended that the DS1822 be

In some situations the bus master may not know whether the DS1822s on the bus are parasite powered or

should be used during temperature conversions. To get this information, the master can issue a Skip ROM

[CCh] command followed by a Read Power Supply [B4h] command followed by a “read-time slot”.

During the read time slot, parasite powered DS1822s will pull the bus low, and externally powered

DS1822s will let the bus remain high. If the bus is pulled low, the master knows that it must supply the

strong pullup on the 1-Wire bus during temperature conversions.

SUPPLYING THE PARASITE-POWERED DS1822 DURING TEMPERATURE

CONVERSIONS Figure 4

POWERING THE DS1822 WITH AN EXTERNAL SUPPLY Figure 5

64-BIT LASERED ROM CODE

Each DS1822 contains a unique 64–bit code (see Figure 6) stored in ROM. The least significant 8 bits of

the ROM code contain the DS1822’s 1-Wire family code: 22h. The next 48 bits contain a unique serial

number. The most significant 8 bits contain a cyclic redundancy check (CRC) byte that is calculated from

the first 56 bits of the ROM code. A detailed explanation of the CRC bits is provided in the CRC

GENERATION section. The 64-bit ROM code and associated ROM function control logic allow the

DS1822 to operate as a 1-Wire device using the protocol detailed in the 1-WIRE BUS SYSTEM section

of this data sheet.

64-BIT LASERED ROM CODE Figure 6

8-BIT CRC 48-BIT SERIAL NUMBER 8-BIT FAMILY CODE (22h)

MSB MSB LSB LSB LSBMSB

VDD (External Supply)

DS1822

GND VDD DQ

VPU

4.7k

To Other

1-Wire Devices

1-Wire Bus

Micro-

processor

VPU

4.7k

1-Wire Bus

Micro-

processor

DS1822

GND VDD DQ

To Other

1-Wire Devices

DS1822

7 of 21

MEMORY

The DS1822’s memory is organized as shown in Figure 7. The memory consists of an SRAM scratchpad

with NV EEPROM storage for the high and low alarm trigger registers (TH and TL) and configuration

purpose memory. All memory commands are described in detail in the DS1822 FUNCTION

COMMANDS section.

Byte 0 and byte 1 of the scratchpad contain the LSB and the MSB of the temperature register,

respectively. These bytes are read-only. Bytes 2 and 3 provide access to TH and TL registers. Byte 4

contains the configuration register data, which is explained in detail in the CONFIGURATION

cannot be overwritten.

Byte 8 of the scratchpad is read-only and contains the cyclic redundancy check (CRC) code for bytes 0

through 7 of the scratchpad. The DS1822 generates this CRC using the method described in the CRC

GENERATION section.

Data is written to bytes 2, 3, and 4 of the scratchpad using the Write Scratchpad [4Eh] command; the data

must be transmitted to the DS1822 starting with the least significant bit of byte 2. To verify data integrity,

the scratchpad can be read (using the Read Scratchpad [BEh] command) after the data is written. When

reading the scratchpad, data is transferred over the 1-Wire bus starting with the least significant bit of

byte 0. To transfer the TH, TL and configuration data from the scratchpad to EEPROM, the master must

issue the Copy Scratchpad [48h] command.

Data in the EEPROM registers is retained when the device is powered down; at power-up the EEPROM

data is reloaded into the corresponding scratchpad locations. Data can also be reloaded from EEPROM to

the scratchpad at any time using the Recall E2 [B8h] command. The master can issue read time slots

following the Recall E2 command and the DS1822 will indicate the status of the recall by transmitting 0

while the recall is in progress and 1 when the recall is done.

DS1822 MEMORY MAP Figure 7

SCRATCHPAD (Power-up State)

byte 0 Temperature LSB (50h)

byte 1 Temperature MSB (05h) EEPROM

byte 2 TH Register or User Byte 1* TH Register or User Byte 1

byte 3 TL Register or User Byte 2* TL Register or User Byte 2

byte 4 Configuration Register* Configuration Register

byte 5 Reserved (FFh)

byte 6 Reserved

byte 7 Reserved (10h)

byte 8 CRC*

*Power-up state depends on value(s) stored

in EEPROM

(85°C)

DS1822

8 of 21

CONFIGURATION REGISTER

Byte 4 of the scratchpad memory contains the configuration register, which is organized as

illustrated in Figure 8. The user can set the conversion resolution of the DS1822 using the R0 and R1

bits in this register as shown in Table 3. The power-up default of these bits is R0 = 1 and R1 = 1 (12-bit

resolution). Note that there is a direct tradeoff between resolution and conversion time. Bit 7 and bits 0–4

in the configuration register are reserved for internal use by the device and cannot be overwritten.

CONFIGURATION REGISTER Figure 8

bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0

0 R1 R0 1 1 1 1 1

THERMOMETER RESOLUTION CONFIGURATION Table 3

R1 R0 Resolution Max Conversion Time

0 0 9-bit 93.75ms (tCONV/8)

0 1 10-bit 187.5ms (tCONV/4)

1 0 11-bit 375ms (tCONV/2)

1 1 12-bit 750ms (tCONV)

CRC GENERATION

CRC bytes are provided as part of the DS1822’s 64-bit ROM code and in the 9th byte of the scratchpad

memory. The ROM code CRC is calculated from the first 56 bits of the ROM code and is contained in the

most significant byte of the ROM. The scratchpad CRC is calculated from the data stored in the

scratchpad, and therefore it changes when the data in the scratchpad changes. The CRCs provide the bus

master with a method of data validation when data is read from the DS1822. To verify that data has been

read correctly, the bus master must recalculate the CRC from the received data and then compare this

value to either the ROM code CRC (for ROM reads) or to the scratchpad CRC (for scratchpad reads). If

the calculated CRC matches the read CRC, the data has been received error free. The comparison of CRC

values and the decision to continue with an operation are determined entirely by the bus master. There is

no circuitry inside the DS1822 that prevents a command sequence from proceeding if the DS1822 CRC

(ROM or scratchpad) does not match the value generated by the bus master.

The equivalent polynomial function of the CRC (ROM or scratchpad) is:

CRC = X8 + X5 + X4 + 1

The bus master can recalculate the CRC and compare it to the CRC values from the DS1822 using the

polynomial generator shown in Figure 9. This circuit consists of a shift register and XOR gates, and the

shift register bits are initialized to 0. Starting with the least significant bit of the ROM code or the least

significant bit of byte 0 in the scratchpad, one bit at a time should shifted into the shift register. After

shifting in the 56th bit from the ROM or the most significant bit of byte 7 from the scratchpad, the

polynomial generator will contain the recalculated CRC. Next, the 8-bit ROM code or scratchpad CRC

from the DS1822 must be shifted into the circuit. At this point, if the recalculated CRC was correct, the

shift register will contain all 0s. Additional information about the Dallas 1-Wire cyclic redundancy check

DS1822

9 of 21

is available in Application Note 27 entitled Understanding and Using Cyclic Redundancy Checks with

Dallas Semiconductor Touch Memory Products.

CRC GENERATOR Figure 9

1-WIRE BUS SYSTEM

The 1-Wire bus system uses a single bus master to control one or more slave devices. The DS1822 is

always a slave. When there is only one slave on the bus, the system is referred to as a “single-drop”

system; the system is “multidrop” if there are multiple slaves on the bus.

All data and commands are transmitted least significant bit first over the 1-Wire bus.

The following discussion of the 1-Wire bus system is broken down into three topics: hardware

configuration, transaction sequence, and 1-Wire signaling (signal types and timing).

HARDWARE CONFIGURATION

The 1-Wire bus has by definition only a single data line. Each device (master or slave) interfaces to the

data line via an open drain or 3-state port. This allows each device to “release” the data line when the

device is not transmitting data so the bus is available for use by another device. The 1-Wire port of the

DS1822 (the DQ pin) is open drain with an internal circuit equivalent to that shown in Figure 10.

The 1-Wire bus requires an external pullup resistor of approximately 5 kΩ; thus, the idle state for the 1-

Wire bus is high. If for any reason a transaction needs to be suspended, the bus MUST be left in the idle

state if the transaction is to resume. Infinite recovery time can occur between bits so long as the 1-Wire

bus is in the inactive (high) state during the recovery period. If the bus is held low for more than 480μs,

all components on the bus will be reset.

HARDWARE CONFIGURATION Figure 10

(MSB) (LSB)

XOR XOR XOR

INPUT

VPU

4.7k

5μA

Typ.

DS1822 1-WIRE PORT

100Ω

FET

RX = RECEIVE

= TRANSMIT

1-wire Bus

DS1822

10 of 21

TRANSACTION SEQUENCE

The transaction sequence for accessing the DS1822 is as follows:

Step 1. Initialization

Step 2. ROM Command (followed by any required data exchange)

Step 3. DS1822 Function Command (followed by any required data exchange)

It is very important to follow this sequence every time the DS1822 is accessed, as the DS1822 will not

respond if any steps in the sequence are missing or out of order. Exceptions to this rule are the Search

ROM [F0h] and Alarm Search [ECh] commands. After issuing either of these ROM commands, the

master must return to Step 1 in the sequence.

INITIALIZATION

All transactions on the 1-Wire bus begin with an initialization sequence. The initialization sequence

consists of a reset pulse transmitted by the bus master followed by presence pulse(s) transmitted by the

slave(s). The presence pulse lets the bus master know that slave devices (such as the DS1822) are on the

bus and are ready to operate. Timing for the reset and presence pulses is detailed in the

1-WIRE SIGNALING section.

ROM COMMANDS

After the bus master has detected a presence pulse, it can issue a ROM command. These commands

operate on the unique 64–bit ROM codes of each slave device and allow the master to single out a

specific device if many are present on the 1-Wire bus. These commands also allow the master to

determine how many and what types of devices are present on the bus or if any device has experienced an

alarm condition. There are five ROM commands, and each command is 8 bits long. The master device

must issue an appropriate ROM command before issuing a DS1822 function command. A flowchart for

operation of the ROM commands is shown in Figure 11.

SEARCH ROM [F0h]

When a system is initially powered up, the master must identify the ROM codes of all slave devices on

the bus, which allows the master to determine the number of slaves and their device types. The master

learns the ROM codes through a process of elimination that requires the master to perform a Search ROM

cycle (i.e., Search ROM command followed by data exchange) as many times as necessary to identify all

of the slave devices. If there is only one slave on the bus, the simpler Read ROM command (see below)

can be used in place of the Search ROM process. For a detailed explanation of the Search ROM

procedure, refer to the iButton Book of Standards at www.ibutton.com/ibuttons/standard.pdf. After every

Search ROM cycle, the bus master must return to Step 1 (Initialization) in the transaction sequence.

READ ROM [33h]

This command can only be used when there is one slave on the bus. It allows the bus master to read the

slave’s 64-bit ROM code without using the Search ROM procedure. If this command is used when there

is more than one slave present on the bus, a data collision will occur when all the slaves attempt to

respond at the same time.

MATCH ROM [55h]

The match ROM command followed by a 64-bit ROM code sequence allows the bus master to address a

specific slave device on a multidrop or single-drop bus. Only the slave that exactly matches the 64-bit

ROM code sequence will respond to the function command issued by the master; all other slaves on the

bus will wait for a reset pulse.

DS1822

11 of 21

SKIP ROM [CCh]

The master can use this command to address all devices on the bus simultaneously without sending out

any ROM code information. For example, the master can make all DS1822s on the bus perform

simultaneous temperature conversions by issuing a Skip ROM command followed by a Convert T [44h]

command.

Note that the Read Scratchpad [BEh] command can follow the Skip ROM command only if there is a

single slave device on the bus. In this case time is saved by allowing the master to read from the slave

without sending the device’s 64-bit ROM code. A Skip ROM command followed by a Read Scratchpad

command will cause a data collision on the bus if there is more than one slave since multiple devices will

attempt to transmit data simultaneously.

ALARM SEARCH [ECh]

The operation of this command is identical to the operation of the Search ROM command except that

only slaves with a set alarm flag will respond. This command allows the master device to determine if

any DS1822s experienced an alarm condition during the most recent temperature conversion. After every

Alarm Search cycle (i.e., Alarm Search command followed by data exchange), the bus master must return

to Step 1 (Initialization) in the transaction sequence. Refer to the OPERATION—ALARM SIGNALING

section for an explanation of alarm flag operation.

DS1822 FUNCTION COMMANDS

After the bus master has used a ROM command to address the DS1822 with which it wishes to

communicate, the master can issue one of the DS1822 function commands. These commands allow the

master to write to and read from the DS1822’s scratchpad memory, initiate temperature conversions and

determine the power supply mode. The DS1822 function commands, which are described below, are

summarized in Table 4 and illustrated by the flowchart in Figure 12.

CONVERT T [44h]

This command initiates a single temperature conversion. Following the conversion, the resulting thermal

data is stored in the 2-byte temperature register in the scratchpad memory and the DS1822 returns to its

low-power idle state. If the device is being used in parasite power mode, within 10μs (max) after this

command is issued the master must enable a strong pullup on the 1-Wire bus for the duration of the

conversion (tconv) as described in the POWERING THE DS1822 section. If the DS1822 is powered by an

external supply, the master can issue read time slots after the Convert T command and the DS1822 will

respond by transmitting 0 while the temperature conversion is in progress and 1 when the conversion is

done. In parasite power mode this notification technique cannot be used since the bus is pulled high by

the strong pullup during the conversion.

WRITE SCRATCHPAD [4Eh]

This command allows the master to write three bytes of data to the DS1822’s scratchpad. The first data

byte is written into the TH register (byte 2 of the scratchpad), the second byte is written into the TL

transmitted least significant bit first. All three bytes MUST be written before the master issues a reset, or

the data may be corrupted.

READ SCRATCHPAD [BEh]

This command allows the master to read the contents of the scratchpad. The data transfer starts with the

least significant bit of byte 0 and continues through the scratchpad until the 9th byte (byte 8–CRC) is read.

The master may issue a reset to terminate reading at any time if only part of the scratchpad data is needed.

COPY SCRATCHPAD [48h]

This command copies the contents of the scratchpad TH, TL and configuration registers (bytes 2, 3, and 4)

to EEPROM. If the device is being used in parasite power mode, within 10μs (max) after this command is

DS1822

12 of 21

issued the master must enable a strong pullup on the 1-Wire bus for at least 10ms as described in the

POWERING THE DS1822 section.

RECALL E2 [B8h]

This command recalls the alarm trigger values (TH and TL) and configuration data from EEPROM and

places the data in bytes 2, 3, and 4, respectively, in the scratchpad memory. The master device can issue

read time slots following the Recall E2 command and the DS1822 will indicate the status of the recall by

transmitting 0 while the recall is in progress and 1 when the recall is done. The recall operation happens

automatically at power-up, so valid data is available in the scratchpad as soon as power is applied to the

device.

READ POWER SUPPLY [B4h]

The master device issues this command followed by a read time slot to determine if any DS1822s on the

bus are using parasite power. During the read time slot, parasite powered DS1822s will pull the bus low,

and externally powered DS1822s will let the bus remain high. Refer to the POWERING THE DS1822

section for usage information for this command.

DS1822 FUNCTION COMMAND SET Table 4

Command

Description

Protocol

1-Wire Bus Activity

After Command is Issued

Notes

TEMPERATURE CONVERSION COMMANDS

Convert T Initiates temperature

conversion. 44h DS1822 transmits conversion

status to master (not applicab le

for parasite-powered DS1822s).

MEMORY COMMANDS

Read Scratchpad Reads the entire scratchpad

including the CRC byte. BEh DS1822 transmits up to 9 data

bytes to master. 2

Write Scratchpad Writes data into scratchpad

bytes 2, 3, and 4 (TH, TL,

and configuration registers).

4Eh Master transmits 3 data bytes to

DS1822. 3

Copy Scratchpad Copies TH, TL, and

configuration register data

from the scratchpad to

EEPROM.

48h None 1

Recall E2 Recalls TH, TL, and

configuration register data

from EEPROM to the

scratchpad.

B8h DS1822 transmits recall status to

master.

Read Power

Supply Signals DS1822 power

supply mode to the master. B4h DS1822 transmits supply status

to master.

NOTES:

1. For parasite-powered DS1822s, the master must enable a strong pullup on the 1-Wire bus during

temperature conversions and copies from the scratchpad to EEPROM. No other bus activity may take

place during this time.

2. The master can interrupt the transmission of data at any time by issuing a reset.

3. All three bytes must be written before a reset is issued.

DS1822

13 of 21

ROM COMMANDS FLOW CHART Figure 11

CCh

SKIP ROM

COMMAND

MASTER TX

RESET PULSE

DS1822 TX

PRESENCE

PULSE

MASTER TX ROM

COMMAND

33h

READ ROM

COMMAND

55h

MATCH ROM

COMMAND

F0h

SEARCH ROM

COMMAND

ECh

ALARM SEARCH

COMMAND

MASTER TX

BIT 0

DS1822 T

BIT 0

DS1822 T

BIT 0

MASTER TX BIT 0

BIT 0

MATCH?

MASTER TX

BIT 1

MATCH?

BIT 63

MATCH?

MASTER TX

BIT 63

Y Y Y Y Y

N N NN

DS1822 T

BIT 1

DS1822 T

BIT 1

MASTER TX BIT 1

DS1822 TX BIT 63

DS1822 T

BIT 63

MASTER T

BIT 63

BIT 0

MAT

BIT 1

MAT

BIT 63

MATCH?

DS1822 TX

FAMILY CODE

1 BYTE

DS1822 TX

SERIAL NUMBER

6 BYTES

DS1822 TX

CRC BYTE

DS1822 T

BIT 0

DS1822 T

BIT 0

MASTER TX BIT 0

DEVICE(S)

WITH ALARM

FLAG SET?

Initialization

Sequence

MASTER TX

FUNCTION

COMMAND

(FIGURE 12)

DS1822

14 of 21

DS1822 FUNCTION COMMANDS FLOW CHART Figure 12

MASTER TX

FUNCTION

COMMAND

44h

CONVERT

TEMPERATURE

PARASITE

POWER

N Y

DS1822 BEGINS

CONVERSION

DEVICE

CONVERTING

TEMPERATURE

MASTER

RX “0s”

MASTER

RX “1s”

MASTER ENABLES

STRONG PULLUP ON DQ

DS1822 CONVERTS

TEMPERATURE

MASTER DISABLES

STRONG PULLUP

48h

COPY

SCRATCHPAD

PARASITE

POWER

MASTER ENABLES

STRONG PULL-UP ON DQ

DATA COPIED FROM

SCRATCHPAD TO EEPROM

MASTER DISABLES

STRONG PULLUP

MASTER

“0s”

COPY IN

PROGRESS

MASTER

RX “1s”

RETURN TO INITIALIZATION

SEQUENCE (FIGURE 11) FOR

NEXT TRANSACTION

B4h

READ

POWER SUPPLY

PARASITE

POWERED

MASTER

RX “1s”

MASTER

RX “0s”

MASTER TX TH BYTE

TO SCRATCHPAD

N 4Eh

WRITE

SCRATCHPAD

MASTER TX TL BYTE

TO SCRATCHPAD

MASTER TX CONFIG. BYTE

TO SCRATCHPAD

BEh

READ

SCRATCHPAD

HAVE 8 BYTES

BEEN READ

MASTER

TX RESET

MASTER RX DATA BYTE

FROM SCRATCHPAD

MASTER RX SCRATCHPAD

CRC BYTE

MASTER

RX “1s”

N B8h

RECALL E2

MASTER BEGINS DATA

RECALL FROM E2 PROM

DEVICE

BUSY RECALLING

DATA

MASTER

RX “0s”

DS1822

15 of 21

1-WIRE SIGNALING

The DS1822 uses a strict 1-Wire communication protocol to insure data integrity. Several signal types are

defined by this protocol: reset pulse, presence pulse, write 0, write 1, read 0, and read 1. All of these

signals, with the exception of the presence pulse, are initiated by the bus master.

INITIALIZATION PROCEDURE: RESET AND PRESENCE PULSES

All communication with the DS1822 begins with an initialization sequence that consists of a reset pulse

from the master followed by a presence pulse from the DS1822. This is illustrated in Figure 13. When the

DS1822 sends the presence pulse in response to the reset, it is indicating to the master that it is on the bus

and ready to operate.

During the initialization sequence the bus master transmits (TX) the reset pulse by pulling the 1-Wire bus

low for a minimum of 480μs. The bus master then releases the bus and goes into receive mode (RX).

When the bus is released, the 5k pullup resistor pulls the 1-Wire bus high. When the DS1822 detects this

rising edge, it waits 15μs to 60μs and then transmits a presence pulse by pulling the 1-Wire bus low for

60μs to 240μs.

INITIALIZATION TIMING Figure 13

READ/WRITE TIME SLOTS

The bus master writes data to the DS1822 during write time slots and reads data from the DS1822 during

read time slots. One bit of data is transmitted over the 1-Wire bus per time slot.

WRITE TIME SLOTS

There are two types of write time slots: “Write 1” time slots and “Write 0” time slots. The bus master

uses a Write 1 time slot to write a logic 1 to the DS1822 and a Write 0 time slot to write a logic 0 to the

DS1822. All write time slots must be a minimum of 60μs in duration with a minimum of a 1μs recovery

time between individual write slots. Both types of write time slots are initiated by the master pulling the

1-Wire bus low (see Figure 14).

To generate a Write 1 time slot, after pulling the 1-Wire bus low, the bus maste r must relea se the 1 -Wire

bus within 15μs. When the bus is released, the 5k pullup resistor will pull the bus high. To generate a

Write 0 time slot, after pulling the 1-Wire bus low, the bus master must continue to hold the bus low for

the duration of the time slot (at least 60μs).

LINE TYPE LEGEND

Bus master pulling low

DS1822 pulling low

Resistor

ullu

VPU

GND

1-WIRE BUS

480μs minimum 480

s minimum

DS1822 TX

presence pulse

60-240μs

MASTER TX RESET PULSE MASTER RX

DS1822

waits 15-60μs

DS1822

16 of 21

The DS1822 samples the 1-Wire bus during a window that lasts from 15μs to 60μs after the master

initiates the write time slot. If the bus is high during the sampling window, a 1 is written to the DS1822.

If the line is low, a 0 is written to the DS1822.

READ/WRITE TIME SLOT TIMING DIAGRAM Figure 14

READ TIME SLOTS

The DS1822 can only transmit data to the master when the master issues read time slots. Therefore, the

master must generate read time slots immediately after issuing a Read Scratchpad [BEh] or Read Power

Supply [B4h] command, so that the DS1822 can provide the requested data. In addition, the master can

generate read time slots after issuing Convert T [44h] or Recall E2 [B8h] commands to find out the status

of the operation as explained in the DS1822 FUNCTION COMMAND section.

All read time slots must be a minimum of 60μs in duration with a minimum of a 1μs recovery time

between slots. A read time slot is initiated by the master device pulling the 1-Wire bus low for a

minimum of 1μs and then releasing the bus (see Figure 14). After the master initiates the read time slot,

the DS1822 will begin transmitting a 1 or 0 on bus. The DS1822 transmits a 1 by leaving the bus high

and transmits a 0 by pulling the bus low. When transmitting a 0, the DS1822 will release the bus by the

end of the time slot, and the bus will be pulled back to its high idle state by the pullup resister. Output

45μs

15μs

VPU

GND

1-WIRE BUS

60μs < TX “0” < 120

s1μs < TREC <

∞

DS1822 Samples

MIN TYP MAX

15μs 30

> 1

MASTER WRITE “0” SLOT MASTER WRITE “1” SLOT

VPU

GND

1-WIRE BUS

MASTER READ “0” SLOT MASTER READ “1” SLOT

Master samples Master samples

START

OF SLOT START

OF SLOT

> 1

1μs < TREC <

∞

15μs 15

s 30μs

DS1822 Samples

MIN TYP MAX

LINE TYPE LEGEND

Bus master pulling low DS1822 pulling low

Resistor pullup

> 1μs

DS1822

17 of 21

data from the DS1822 is valid for 15μs after the falling edge that initiated the read time slot. Therefore,

the master must release the bus and then sample the bus state within 15μs from the start of the slot.

Figure 15 illustrates that the sum of TINIT, TRC, and TSAMPLE must be less than 15μs for a read time slot.

Figure 16 shows that system timing margin is maximized by keeping TINIT and TRC as short as possible

and by locating the master sample time during read time slots towards the end of the 15μs period.

DETAILED MASTER READ 1 TIMING Figure 15

RECOMMENDED MASTER READ 1 TIMING Figure 16

RELATED APPLICATION NOTES

The following Application Notes can be applied to the DS1822. These notes can be obtained from the

Dallas Semiconductor “Application Note Book,” via the Dallas website at http://www.dalsemi.com/, or

through our faxback service at (214) 450–0441.

Application Note 27: Understanding and Using Cyclic Redundancy Checks with Dallas Semiconductor

Touch Memory Product

Application Note 55: Extending the Contact Range of Touch Memories

Application Note 74: Reading and Writing Touch Memories via Serial Interfaces

Application Note 104: Minimalist Temperature Control Demo

Application Note 106: Complex MicroLANs

Application Note 108: MicroLAN—In the Long Run

Application Note 162: Interfacing the DS18X20/DS1822 1-Wire Temperature Sensor in a

Microcontroller Environment

Sample 1-Wire subroutines that can be used in conjunction with AN74 can be downloaded from the

Dallas website or anonymous FTP Site.

VPU

GND

1-WIRE BUS

IH of Master

TRC

TINT > 1μs Master samples

LINE TYPE LEGEND

Bus master pulling low

Resistor pullup

VPU

GND

1-WIRE BUS

VIH of Master

TRC =

small

TINT =

small

Master samples

DS1822

18 of 21

DS1822 OPERATION EXAMPLE 1

In this example there are multiple DS1822s on the bus and they are using parasite power. The bus master

initiates a temperature conversion in a specific DS 1822 and then reads its scratchpad and recalculates the

CRC to verify the data.

MASTER MODE DATA (LSB FIRST) COMMENTS

TX Reset Master issues reset pulse.

RX Presence DS1822s respond with presence pulse.

TX 55h Master issues Match ROM command.

TX 64-bit ROM code Master sends DS1822 ROM code.

TX 44h Master issues Convert T command.

TX DQ line held high by

strong pullup Master applies strong pullup to DQ for the duration of the

conversion (tconv).

TX Reset Master issues reset pulse.

RX Presence DS1822s respond with presence pulse.

TX 55h Master issues Match ROM command.

TX 64-bit ROM code Master sends DS1822 ROM code.

TX BEh Master issues Read Scratchpad command.

RX 9 data bytes Master reads entire scratchpad including CRC. The master

then recalculates the CRC of the first eight data bytes from the

scratchpad and compares the calculated CRC with the read

CRC (byte 9). If they match, the master continues; if not, the

read operation is repeated.

DS1822 OPERATION EXAMPLE 2

In this example there is only one DS1822 on the bus and it is using parasite power. The master writes to

the TH, TL, and configuration registers in the DS1822 scratchpad and then reads the scratchpad and

recalculates the CRC to verify the data. The master then copies the scratchpad contents to EEPROM.

MASTER MODE DATA (LSB FIRST) COMMENTS

TX Reset Master issues reset pulse.

RX Presence DS1822 responds with presence pulse.

TX CCh Master issues Skip ROM command.

TX 4Eh Master issues Write Scratchpad command.

TX 3 data bytes Master sends three data bytes to scratchpad (TH, TL, and config).

TX Reset Master issues reset pulse.

RX Presence DS1822 responds with presence pulse.

TX CCh Master issues Skip ROM command.

TX BEh Master issues Read Scratchpad command.

RX 9 data bytes Master reads entire scratchpad including CRC. The master then

recalculates the CRC of the first eight data by tes from the

scratchpad and compares the calculated CRC with the read CRC

(byte 9). If they match, the master continues; if not, the read

operation is repeated.

TX Reset Master issues reset pulse.

RX Presence DS1822 responds with presence pulse.

TX CCh Master issues Skip ROM command.

TX 48h Master issues Copy Scratchpad command.

TX DQ line held high by

strong pullup Master applies strong pullup to DQ for at least 10ms while copy

operation is in progress.

DS1822

19 of 21

ABSOLUTE MAXIMUM RATINGS*

Voltage on Any Pin Relative to Ground -0.5V to +6.0V

Operating Temperature Range -55°C to +125°C

Storage Temperature Range -55°C to +125°C

Solder Dip Temperature See IPC/JEDEC J-STD-020A Specification

Reflow Oven Temperature +220°C

*These are stress ratings only and functional operation of the device at these or any other conditions

above those indicated in the operation sections of this specification is not implied. Exposure to absolute

maximum rating conditions for extended periods of time may affect reliability.

DC ELECTRICAL CHARACTERISTICS (-55°C to +125°C; VDD = 3.0V to 5.5V)

PARAMETER SYMBOL CONDITION MIN TYP MAX UNITS NOTES

Supply Voltage VDD Local Power +3.0 +5.5 V 1

Parasite Power +3.0 +5.5 Pullup Supply

Voltage VPU Local Power +3.0 VDD V 1, 2

-10°C to

+85°C ±2

Thermometer Error tERR

-55°C to

+125°C ±3

°C

Input Logic Low VIL -0.3 +0.8 V 1, 4, 5

Local Power

+2.2 Input Logic High VIH

Parasite Power +3.0

The lower of

5.5

VDD + 0.3

V 1, 6

Sink Current IL V

I/O=0.4V 4.0 mA 1

Standby Current IDDS 750 1000 nA 7, 8

Active Current IDD V

DD=5V 1 1.5 mA 9

DQ Input Current IDQ 5 µA 10

Drift ±0.2 °C 11

NOTES:

1. All voltages are referenced to ground.

2. The Pullup Supply Voltage specification assumes that the pullup device is ideal, and therefore the

high level of the pullup is equal to VPU. In order to meet the VIH spec of the DS1822, the actual

supply rail for the strong pullup transistor must include margin for the voltage drop across the

transistor when it is turn ed on; thus: VPU_ACTUAL = VPU_IDEAL + VTRANSISTOR.

3. See typical performance curve in Figure 17.

4. Logic low voltages are specified at a sink current of 4mA.

5. To guarantee a presence pulse under low voltage parasite power conditions, VILMAX may have to be

reduced to as low as 0.5V.

6. Logic high voltages are specified at a source current of 1mA.

7. Standby current specified up to +70°C. Standby current typically is 3μA at +125°C.

8. To minimize IDDS, DQ should be within the following ranges: GND ≤ DQ ≤ GND + 0.3V or VDD -

0.3V ≤ DQ ≤ VDD.

9. Active current refers to supply current during active temperature conversions or EEPROM writes.

10. DQ line is high (high-Z state).

11. Drift data is based on a 1000 hour stress test at +125°C with VDD = 5.5V.

DS1822

20 of 21

AC ELECTRICAL CHARACTERISTICS: NV MEMORY

(-55°C to +100°C; VDD = 3.0V to 5.5V)

PARAMETER SYMBOL CONDITION MIN TYP MAX UNITS

NV Write Cycle Time twr 2 10 ms

EEPROM Writes NEEWR -55°C to +55°C 50k writes

EEPROM Data Retention t EEDR -55°C to +55°C 10 years

AC ELECTRICAL CHARACTERISTICS (-55°C to +125°C; VDD = 3.0V to 5.5V)

PARAMETER SYMBOL CONDITION MIN TYP MAX UNITS NOTES

Temperature Conversion tCONV 9-bit resolution 93.75 ms 1

Time 10-bit resolution 187.5 ms 1

11-bit resolution 375 ms 1

12-bit resolution 750 ms 1

Time to Strong Pullup On tSPON Start Convert T

Command Issued 10 µs

Time Slot tSLOT 60 120 µs 1

Recovery Time tREC 1 µs 1

Write 0 Low Time rLOW0 60 120 µs 1

Write 1 Low Time tLOW1 1 15 µs 1

Read Data Valid tRDV 15 µs 1

Reset Time High tRSTH 480 µs 1

Reset Time Low tRSTL 480 µs 1,2

Presence Detect High tPDHIGH 15 60 µs 1

Presence Detect Low tPDLOW 60 240 µs 1

Capacitance CIN/OUT 25 pF

NOTES:

1. Refer to timing diagrams in Figure 18.

2. Under parasite power, if tRSTL > 960μs, a power on reset may occur.

TYPICAL PERFORMANCE CURVE Figure 17

DS1822 Typi cal Performance Curve

-1.2

-1

-0.8

-0.6

-0.4

-0.2

0.2

0.4

0.6

0.8

-10 0 10 20 30 40 50 60 70 80

Temperature (°C)

Thermometer Error (°C)

+3s Error

-3s Error

Mean Error

DS1822

TIMING DIAGRAMS Figure 18



Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000

Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied.

Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical

Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.