TSOP382.., TSOP384.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES * Very low supply current * Photo detector and preamplifier in one package * Internal filter for PCM frequency * Supply voltage: 2.5 V to 5.5 V * Improved immunity against ambient light * Insensitive to supply voltage ripple and noise 1 * Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 2 3 19026 DESIGN SUPPORT TOOLS DESCRIPTION click logo to get started These products are miniaturized IR receiver modules for infrared remote control systems. A PIN diode and a preamplifier are assembled on a leadframe, the epoxy package contains an IR filter. Models Available MECHANICAL DATA The demodulated output signal can be directly connected to a microprocessor for decoding. Pinning for TSOP382.., TSOP384..: 1 = OUT, 2 = GND, 3 = VS The TSOP384.. series devices are optimized to suppress almost all spurious pulses from energy saving lamps like CFLs. The AGC4 used in the TSOP384.. may suppress some data signals. The TSOP382.. series are provided primarily for compatibility with old AGC2 designs. New designs should prefer the TSOP384.. series containing the newer AGC4. These components have not been qualified according to automotive specifications. PARTS TABLE LEGACY, FOR LONG BURST REMOTE CONTROLS (AGC2) RECOMMENDED FOR LONG BURST CODES (AGC4) 30 kHz TSOP38230 TSOP38430 33 kHz TSOP38233 TSOP38433 36 kHz TSOP38236 TSOP38436 (1)(2)(3) 38 kHz TSOP38238 TSOP38438 (4)(5) AGC Carrier frequency 40 kHz TSOP38240 TSOP38440 56 kHz TSOP38256 TSOP38456 (6)(7) Package Minicast Pinning 1 = OUT, 2 = GND, 3 = VS Dimensions (mm) 5.0 W x 6.95 H x 4.8 D Mounting Leaded Application Best choice for Rev. 1.7, 24-Sep-2018 Remote control (1) RC-5 (2) RC-6 (3) 1 Panasonic (4) NEC (5) Sharp (6) r-step (7) Thomson RCA Document Number: 82491 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP382.., TSOP384.. www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 16833-13 17170-11 3 R1 Transmitter with TSALxxxx VS 1 Input Band pass AGC Demodulator + VS C1 Circuit 30 k IR receiver C OUT VO GND GND 2 PIN Control circuit R1 and C1 recommended to reduce supply ripple for VS < 2.8 V ABSOLUTE MAXIMUM RATINGS PARAMETER Supply voltage Supply current Output voltage Output current Junction temperature Storage temperature range Operating temperature range Power consumption Soldering temperature TEST CONDITION SYMBOL VS IS VO IO Tj Tstg Tamb Ptot Tsd Tamb 85 C t 10 s, 1 mm from case VALUE -0.3 to +6 3 -0.3 to (VS + 0.3) 5 100 -25 to +85 -25 to +85 10 260 UNIT V mA V mA C C C mW C Note * Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION Ev = 0, VS = 3.3 V Ev = 40 klx, sunlight Supply current Supply voltage SYMBOL ISD ISH VS MIN. 0.27 2.5 TYP. 0.35 0.45 - MAX. 0.45 5.5 UNIT mA mA V d - 24 - m VOSL - - 100 mV Ee min. - 0.12 0.25 mW/m2 Ee max. 1/2 30 - 45 - W/m2 Ev = 0, test signal see Fig. 1, IR diode TSAL6200, IF = 50 mA IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see Fig. 1 Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see Fig. 1 tpi - 5/fo < tpo < tpi + 6/fo, test signal see Fig. 1 Angle of half transmission distance Transmission distance Output voltage low Minimum irradiance Maximum irradiance Directivity TYPICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) Optical Test Signal 1.0 (IR diode TSAL6200, IF = 0.4 A, 30 pulses, f = f0, t = 10 ms) t tpi * T 10/f0 is recommended for optimal function * tpi VO Output Signal VOL 16110 1) 7/f0 < td < 15/f0 2) tpi - 5/f0 < tpo < tpi + 6/f0 VOH Output pulse width 0.9 tpo - Output Pulse Width (ms) Ee 0.8 Input burst length 0.7 0.6 0.5 0.4 0.3 = 950 nm, optical test signal, Fig. 1 0.2 0.1 0 0.1 td 1) tpo 2) t 20752 Fig. 1 - Output Active Low Rev. 1.7, 24-Sep-2018 1 10 102 103 104 105 Ee - Irradiance (mW/m2) Fig. 2 - Pulse Length and Sensitivity in Dark Ambient 2 Document Number: 82491 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP382.., TSOP384.. www.vishay.com Ee min. - Threshold Irradiance (mW/m2) Ee Vishay Semiconductors Optical Test Signal 600 s t 600 s t = 60 ms 94 8134 Output Signal, (see Fig. 4) VO VOH VOL t off t on 4.0 Correlation with ambient light sources: 10 W/m2 = 1.4 klx (std. illum. A, T = 2855 K) 10 W/m2 = 8.2 klx (daylight, T = 5900 K) 3.5 3.0 Wavelength of ambient illumination: = 950 nm 2.5 2.0 1.5 1.0 0.5 0 0.01 t 20757 ton, toff - Output Pulse Width (ms) 0.8 ton 0.7 0.6 0.5 toff 0.4 0.3 0.2 = 950 nm, optical test signal, Fig. 3 0.1 0 0.1 1 10 100 1000 10 000 Ee - Irradiance (mW/m2) 20759 10 100 3.0 2.5 f = f0 f = 30 kHz f = 10 kHz f = 100 Hz 2.0 1.5 1.0 0.5 0 1 10 100 1000 VS RMS - AC Voltage on DC Supply Voltage (mV) Fig. 4 - Output Pulse Diagram Fig. 7 - Sensitivity vs. Supply Voltage Disturbances 1.0 1.2 0.9 Max. Envelope Duty Cycle Ee min./Ee - Relative Responsivity 1 Fig. 6 - Sensitivity in Bright Ambient Ee min. - Threshold Irradiance (mW/m2) Fig. 3 - Output Function 0.1 Ee - Ambient DC Irradiance (W/m2) 1.0 0.8 0.6 0.4 f = f0 5 % f(3 dB) = f0/10 0.2 0.8 0.7 0.6 0.5 TSOP382.. 0.4 TSOP384.. 0.3 0.2 0.1 f = 38 kHz, Ee = 2 mW/m 0 0.0 0.7 16925 0.9 1.1 0 1.3 f/f0 - Relative Frequency Fig. 5 - Frequency Dependence of Responsivity Rev. 1.7, 24-Sep-2018 20 40 60 80 100 120 Burst Length (number of cycles/burst) Fig. 8 - Max. Envelope Duty Cycle vs. Burst Length 3 Document Number: 82491 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP382.., TSOP384.. Ee min. - Threshold Irradiance (mW/m2) www.vishay.com Vishay Semiconductors 0.30 0 10 20 30 0.25 0.20 40 1.0 0.15 0.10 0.9 50 0.8 60 70 0.05 0.7 80 0 -30 -10 10 30 50 70 90 0.6 Tamb - Ambient Temperature (C) 0.4 Fig. 9 - Sensitivity vs. Ambient Temperature 0 Fig. 12 - Vertical Directivity 0.30 Ee min. - Sensitivity (mW/m2) 1.2 S ()rel - Relative Spectral Sensitivity 0.2 d rel - Relative Transmission Distance 19259 1.0 0.8 0.6 0.4 0.2 0.25 0.20 0.15 0.10 0.05 0.00 0 750 850 1050 950 1 1150 - Wavelength (nm) 94 8408 Fig. 10 - Relative Spectral Sensitivity vs. Wavelength 0 10 2 3 4 5 VS - Supply Voltage (V) Fig. 13 - Sensitivity vs. Supply Voltage 20 30 40 1.0 0.9 50 0.8 60 70 0.7 80 0.6 19258 0.4 0.2 0 drel - Relative Transmission Distance Fig. 11 - Horizontal Directivity Rev. 1.7, 24-Sep-2018 4 Document Number: 82491 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP382.., TSOP384.. www.vishay.com Vishay Semiconductors SUITABLE DATA FORMAT Axis Title This series is designed to suppress spurious output pulses due to noise or disturbance signals. The devices can distinguish data signals from noise due to differences in frequency, burst length, and envelope duty cycle. The data signal should be close to the device's band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below. 10000 7 When a data signal is applied to the product in the presence of a disturbance, the sensitivity of the receiver is automatically reduced by the AGC to insure that no spurious pulses are present at the receiver's output. 5 1000 1st line 2nd line 2nd line IR Signal Amplitude 6 4 3 100 2 1 Some examples which are suppressed are: 10 0 * DC light (e.g. from tungsten bulbs sunlight) 0 5 15 20 Time (ms) 16920 * Continuous signals at any frequency 10 Fig. 14 - IR Disturbance from Fluorescent Lamp With Low Modulation * Strongly or weakly modulated patterns from fluorescent lamps with electronic ballasts (see Fig. 14 or Fig. 15) Axis Title 10000 40 1000 0 1st line 2nd line 2nd line IR Signal Amplitude 20 -20 100 -40 10 -60 0 5 10 15 20 Time (ms) 16921 Fig. 15 - IR Disturbance from Fluorescent Lamp With High Modulation TSOP382.. TSOP384.. Minimum burst length 10 cycles/burst 10 cycles/burst After each burst of length a minimum gap time is required of 10 to 70 cycles 10 cycles 10 to 35 cycles 10 cycles For bursts greater than a minimum gap time in the data stream is needed of 70 cycles > 4 x burst length 35 cycles > 10 x burst length Maximum number of continuous short bursts/second 1800 1500 NEC code Yes Preferred RC5/RC6 code Yes Preferred Thomson 56 kHz code Yes Preferred Sharp code Yes Preferred Mild disturbance patterns are suppressed (example: signal pattern of Fig. 14) Complex and critical disturbance patterns are suppressed (example: signal pattern of Fig. 15 or highly dimmed LCDs) Suppression of interference from fluorescent lamps Notes * For data formats with short bursts please see the datasheet for TSOP383.., TSOP385.. * For Sony 12, 15, and 20 bit IR codes please see the datasheet of TSOP38S40 Rev. 1.7, 24-Sep-2018 5 Document Number: 82491 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP382.., TSOP384.. www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 5 4.8 (4) 2.8 (5.55) 6.95 0.3 8.25 0.3 R2 0.9 1.1 30.5 0.5 (1.54) 0.85 max. 0.7 max. 2.54 nom. 2.54 nom. 0.5 max. 1.2 0.2 Marking area technical drawings according to DIN specifications Not indicated to lerances 0.2 Drawing-No.: 6.550-5263.01-4 Issue: 12; 16.04.10 19009 Rev. 1.7, 24-Sep-2018 R2 6 Document Number: 82491 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. (c) 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 08-Feb-17 1 Document Number: 91000 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Vishay: TSOP38238 TSOP38238SS1V TSOP39238CZ1 TSOP38436 TSOP38438 TSOP38236 TSOP38256 TSOP38430 TSOP39440 TSOP39240 TSOP39456 TSOP39256 TSOP38433 TSOP38440 TSOP38456 TSOP38230