YAGEO CORPORATION ALUMINUM ELECTROLYTIC CAPACITORS SG [ Electronic Ballast ] Miniature Size Aluminum Electrolytic Capacitors 105C Single-Ended Lead Aluminum Electrolytic Capacitors FEATURES Life Time : 105C, 5000 Hours Radial Lead Type with the Standard Case Sizes Ranging from o10 x 19 to o22 x 40 RECOMMENDED APPLICATIONS Long Life 5000 Hours at 105C Assured with Full Rated Maximum Ripple Current Applied DESCRIPTION Suitable for Electronic Ballast and Other Long Life Equipment Special designs are available upon requests. For Detail Specifications, Please Refer to Engineering Bulletin No. 2064 FREQUENCY CORRECTION FACTOR FOR RIPPLE CURRENT FREQUENCY (Hz) CORRECTION FACTOR 50.60 0.80 120 1.00 300 1.20 1K 1.40 10K ~ 100K 1.60 DIAGRAM OF DIMENSIONS Dimensions : mm do 4.0 5.0 6.0 8.0 10.0 12.0 13.0 16.0 18.0 22.0 1.5 2.0 2.5 3.5 5.0 0.45 0.5 Rubber Stand-off Rubber End Seal Vinyl Sleeve (P.V.C) Rubber End Seal Vinyl Sleeve (P.V.C) F0.5 F F0.5 Do 0.6 0.4Max. 15Min. L 7.5 0.8 10.0 0.8 L 12 13 L 15 L 16 L + 1.5Max. +1.0 L -0.5 L + 2.0Max. 5Min. D0.5 L 15Min. 5Min. D0.5 33 SPECIFICATIONS Operating Temp. Range 160 to 400VDC : -40 to +105C Working Voltage 160 to 450VDC Rate Capacitance Range 3.3 to 330F Capacitance Tolerance 20% (120HZ / +25C) DC Leakage Current I 0.06cv + 10 (A) After 2 Minutes Application of Rated Working Voltage at +25C D.F WV(V) 120HZ / +25C 160 200 250 350 400 450 D.F (%) 15 15 15 20 24 24 Characteristics at W V (V) 160 200 250 350 400 450 Low Temperature Z (-25C) / Z (+20C) 3 3 3 5 5 6 Z (-40C) / Z (+20C) 6 6 6 6 6 Endurance (Load Life) After 5000 hours application of DC voltage with specified ripple current ( rated DC working voltage) at +105C, the capacitor shall meet the following limits. Shelf Life 450VDC : -25 to +105C Capacitance Change 20% of Initial Measured Value Dissipation Factor 200% of Initial Specified Value Leakage Current Initial Specified Value 1000 Hours No Voltage Applied Capacitance Change Within 20% of Initial Value Dissipation Factor Not Exceed 200% of Initial Requirement Leakage Current Not Exceed 200% of Initial Requirement CASE SIZE OF STANDARD PRODUCTS Do 6mm with Safety Vent at Can Bottom CAP. (F) WV (SV) 160 (200) DxL IMPEDANCE 200 (250) RIPPLE CURRENT DxL IMPEDANCE 250 (300) RIPPLE CURRENT DxL IMPEDANCE 350 (400) RIPPLE CURRENT DxL IMPEDANCE 400 (450) RIPPLE DxL CURRENT IMPEDANCE 450 (500) RIPPLE CURRENT 3.3 10.0 33.0 47.0 68.0 100.0 150.0 220.0 330.0 IMPEDANCE 10x19 6.5 4.7 22.0 DxL 10x19 1.52 10x19 1.30 13x20 0.95 160 210 260 10x19 1.50 13x20 0.95 13x20 0.91 160 210 260 13x20 3.6 80 100 10x19 3.0 100 10x19 2.9 100 13x20 3.0 110 13x20 2.5 160 13x20 2.1 160 13x25 1.35 170 16x25 1.8 190 16x20 1.00 200 18x20 2.2 200 13x20 1.9 210 13x25 1.00 230 16x25 0.95 230 16x32 1.3 275 16x20 0.91 250 18x20 0.91 250 18x25 1.2 280 18x32 1.0 340 13x25 1.7 270 16x25 0.75 300 16x32 0.75 300 16x20 1.5 275 18x20 0.80 315 18x25 0.80 325 18x36 0.49 420 18x40 0.8 460 18x40 0.34 545 22x40 0.6 580 22x40 0.30 650 13x25 0.60 360 13x25 0.60 360 16x25 0.80 380 16x32 0.50 400 430 16x20 0.55 430 18x20 0.90 375 18x25 0.55 380 18x32 0.40 530 16x25 0.30 475 16x25 0.30 475 16x32 0.65 520 18x20 0.31 465 18x20 0.31 465 18x25 0.65 500 16x32 0.22 650 18x25 0.27 650 18x32 0.45 650 18x25 0.24 625 18x32 0.22 780 18x40 0.35 820 16x32 0.22 750 725 18x32 0.22 960 60 10x19 3.5 16x20 0.55 18x25 0.24 RIPPLE CURRENT Note : oD x L : mm, Ripple Current Spec : 120HZ / +105C (mA, rms), Impedance Spec : 100KHZ / +25C ( Max.) 34 LOAD LIFE Capacitance Change Ratio Leakage Current Change 10 C/C 0 (%) -10 47F 400v -20 250F 200v 0 500 1000 3000 1000 500 5000 Time in Hours LC (A) 100 Dissipation Factor Change 50 47F 400v 220F 200v 40 D.F (%) 0 500 1000 3000 5000 Time in Hours 30 20 47F 400v 10 0 220F 200v 0 500 1000 3000 5000 Time in Hours TEMPERATURE CHARACTERISTICS Capacitance Change Ratio Dissipation Factor Change 100 40 30 20 C/C 10 0 (%) -10 -20 -30 50 47F 400v 220F 200v D.F (%) 10 47F 400v 5 -40 0 40 80 220F 200v 120 Temperature in C -40 0 40 80 120 Temperature in C