37.0-40.0 GHz GaAs Power Amplifier QFN, 7x7mm P1080-QU January 2011 - Rev 10-Jan-11 Features Linear Power Amplifier On-Chip Power Detector Output Power Adjust 25.0 dB Small Signal Gain +27.0 dBm P1dB Compression Point +38.0 dBm OIP3 General Description Absolute Maximum Ratings1,2 Mimix Broadband's four stage 37.0-40.0 GHz packaged GaAs MMIC power amplifier has a small signal gain of 25.0 dB with a +38.0 dBm Output Third Order Intercept. The amplifier contains an integrated, temperature compensated, on-chip power detector. This MMIC uses Mimix Broadband's GaAs pHEMT device model technology, and is based upon electron beam lithography to ensure high repeatability and uniformity. The device comes in a RoHS compliant 7x7mm QFN Surface Mount Package offering excellent RF and thermal properties. This device has been designed for use in 38 GHz Point-to-Point Microwave Radio applications. Supply Voltage (Vd) Gate Bias Voltage (Vg) Input Power (Pin) Abs. Max. Junction/Channel Temp Max. Operating Junction/Channel Temp +4.3V -1.5V < Vg < 0V 15 dBm See MTTF Graph 1 175 C Continuous Power Dissipation (Pdiss) at 85 C 7.0 W Thermal Resistance (Tchannel=150 C) 12 C/W -40 to +85 C Operating Temperature (Ta) -65 to +150 C Storage Temperature (Tstg) Mounting Temperature See solder reflow profile ESD Min. - Machine Model (MM) Class A ESD Min. - Human Body Model (HBM) Class 1A MSL Level MSL3 (1) Channel temperature directly affects a device's MTTF. Channel temperature should be kept as low as possible to maximize lifetime. (2) For saturated performance it recommended that the sum of (2*Vdd + abs(Vgg)) <9V Electrical Characteristics for 37 - 40 GHz (Ambient Temperature T = 25 oC) Parameter Frequency Range (f ) Input Return Loss (S11) Output Return Loss (S22) Small Signal Gain (S21) Gain Flatness ( S21) Reverse Isolation (S12) Output Power for 1dB Compression (P1dB) Output IMD3 with Pout (scl) = 14 dBm Output IP3 Drain Bias Voltage (Vd) Gate Bias Voltage (Vg) Supply Current (Id1) (Vd=4.0V, Vg=-0.3V) Units GHz dB dB dB dB dB dBm dBc dBm VDC VDC mA Min. 37.0 10.0 4.0 21.0 43.0 35.5 -1.0 - Typ. 14.0 8.0 25.0 +/-1.0 50 27.0 48.0 +38.0 4.0 -0.3 1000 Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Max. 40.0 30.0 4.0 -0.1 1200 Page 1 of 6 Characteristic Data and Specifications are subject to change without notice. (c)2011 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 37.0-40.0 GHz GaAs Power Amplifier QFN, 7x7mm P1080-QU January 2011 - Rev 10-Jan-11 Power Amplifier Measurements XP1080-QU-0N00: Input Return Loss (S11) Vd=4.0V, Id=1000mA XP1080-QU-0N00: Small signal Gain (S21) Vd=4.0V, Id=1000mA 30 28 26 |S11| (dB) |S21| (dB) 24 22 20 18 16 14 12 10 37 37.5 38 38.5 39 39.5 0 -2 -4 -6 -8 -10 -12 -14 -16 -18 -20 -22 -24 -26 -28 -30 37 40 37.5 38 38.5 |S12| (dB) |S22| (dB) 0 -2 -4 -6 -8 -10 -12 -14 -16 -18 -20 -22 -24 -26 -28 -30 37.5 38 38.5 39 39.5 40 0 -5 -10 -15 -20 -25 -30 -35 -40 -45 -50 -55 -60 -65 -70 37 40 37.5 38 38.5 39 39.5 40 Frequency (GHz) Frequency (GHz) XP1080-QU-0N00; C/I3 vs Freq Pscl=14dBm, Vd=4V, Id=1000mA XP1080-QU-0N00; Output IP3 vs Freq Vd=4V, Id=1000mA 60 46 58 44 56 42 54 C/I3 (dBc) OIP3 (dBm) 39.5 XP1080-QU-0N00: Reverse Isolation (S12) Vd=4.0V, Id=1000mA XP1080-QU-0N00: Output Return Loss (S22) Vd=4.0V, Id=1000mA 37 39 Frequency (GHz) Frequency (GHz) 40 38 36 52 50 48 46 34 44 32 42 40 30 37 37.5 38 38.5 Frequency (GHz) 39 39.5 40 37 37.5 38 38.5 39 39.5 Frequency (GHz) Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 2 of 6 Characteristic Data and Specifications are subject to change without notice. (c)2011 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 40 37.0-40.0 GHz GaAs Power Amplifier QFN, 7x7mm P1080-QU January 2011 - Rev 10-Jan-11 Power Amplifier Measurements (cont.) XP1080-QU: P1dB vs Freq Vd=4V, Id=1000mA XP1080-QU: Psat vs Freq Vd=4V, Id=1000mA 30 30 29.5 29.5 29 29 28.5 28.5 28 28 27.5 27.5 27 27 26.5 26.5 26 26 25.5 25.5 25 25 37 37.5 38 38.5 39 39.5 37 40 37.5 38 38.5 39 39.5 Frequency (GHz) Frequency (GHz) XP1080-QU: Detector Output (Diff) vs Freq Vd=4V, Id=1000mA, Vdet/ref Bias = +5V/100k 10000 1000 37GHz 38.25GHz 39.5GHz 100 10 0 5 10 15 20 25 30 Pout (dBm) Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 3 of 6 Characteristic Data and Specifications are subject to change without notice. (c)2011 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 40 37.0-40.0 GHz GaAs Power Amplifier QFN, 7x7mm P1080-QU January 2011 - Rev 10-Jan-11 Physical Dimensions/Layout QU Pin Number Pin Name 1 2 3 4 RF IN VG1 VG2 VG3 5,6 NC Pin Function RF Input Gate bias, Stage 1 Gate bias, Stage 2 Gate bias, Stage 3 Nominal Value 0 -0.3 V, 700k . -0.3 V, 700k . -0.3 V, 600k . Not Connected 7 Vref Detector reference output +5.0 V thru 100k (2.5M ) +5.0 V thru 100k (2.5M ) 8 Vdet Detector output 9 RF OUT RF Output 10 VD3 Drain bias for stage 3 +4.0 V, 533mA, 0.9 11 VD2 Drain bias for stage 2 +4.0 V, 267mA, 1.1 12 VD1 Drain bias for stage 1 +4.0 V, 200mA, 1.6 13,14 15 16 NC PDC PDA >1M Not Connected Not Connected Not Connected VD1 VD2 13 12 Bypass Capacitors - See App Note [2] VD3 10 NC 11 NC 6 7 8 VG1 VG2 VG3 5 4 9 3 1 2 RF IN 15 16 PDA PDC 14 Functional Block Diagram/Board Layout NC NC Vref Vdet RF OUT Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 4 of 6 Characteristic Data and Specifications are subject to change without notice. (c)2011 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 37.0-40.0 GHz GaAs Power Amplifier QFN, 7x7mm P1080-QU January 2011 - Rev 10-Jan-11 App Note [1] Biasing - It is recommended to bias the amplifier with Vd=4.0V and Id=1000mA. It is also recommended to use active biasing to keep the currents constant as the RF power and temperature vary; this gives the most reproducible results. Depending on the supply voltage available and the power dissipation constraints, the bias circuit may be a single transistor or a low power operational amplifier, with a low value resistor in series with the drain supply used to sense the current. The gate of the pHEMT is controlled to maintain correct drain current and thus drain voltage. The typical gate voltage needed to do this is -0.3V. Typically the gate is protected with Silicon diodes to limit the applied voltage. Also, make sure to sequence the applied voltage to ensure negative gate bias is available before applying the positive drain supply. App Note [2] Bias Arrangement Each DC pin (Vd1,2,3 and Vg1,2,3) needs to have DC bypass capacitance (10 nF/1 uF) as close to the package as possible. App Note [3] Power Detector - As shown in the schematic below, the power detector is implemented by providing +5V bias and measuring the difference in output voltage with standard op-amp in a differential mode configuration. MTTF XP1080-QK-0N00: MTTF hours vs Package Base Temperature Vd=4V, Id=1000mA XP1080-QK-0N00: Tch(max) vs Package Base Temperature Vd=4V, Id=1000mA 1.0E+14 200 1.0E+13 1.0E+11 1.0E+10 1.0E+09 1.0E+08 1.0E+07 6 150 Pdiss (W) Tch max (C) MTTF (hours) 7 175 1.0E+12 XP1080-QK-0N00: Operating Power De-rating Curve (continuous) 8 125 100 5 4 3 2 1.0E+06 75 1.0E+05 1.0E+04 1 0 50 1.0E+03 20 20 30 40 50 60 70 80 90 100 110 120 30 40 50 130 60 70 80 90 100 110 120 130 25 50 75 100 125 150 Package Base Temp (C) Package Base Temp (C) Package Base Temp (C) Typical Application IF IN TX PA + DET DRIVER DET DIPLEXER TX Filter (if required) X2 XU1019-QH XB1014-QT XP1080-QU LO Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 5 of 6 Characteristic Data and Specifications are subject to change without notice. (c)2011 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws. 175 37.0-40.0 GHz GaAs Power Amplifier QFN, 7x7mm P1080-QU January 2011 - Rev 10-Jan-11 Handling and Assembly Information CAUTION! - Mimix Broadband MMIC Products contain gallium arsenide (GaAs) which can be hazardous to the human body and the environment. For safety, observe the following procedures: * Do not ingest. * Do not alter the form of this product into a gas, powder, or liquid through burning, crushing, or chemical processing as these by-products are dangerous to the human body if inhaled, ingested, or swallowed. * Observe government laws and company regulations when discarding this product. This product must be discarded in accordance with methods specified by applicable hazardous waste procedures. Life Support Policy - Mimix Broadband's products are not authorized for use as critical components in life support devices or systems without the express written approval of the President and General Counsel of Mimix Broadband. As used herein: (1) Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. (2) A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Package Attachment - This packaged product from Mimix Broadband is provided as a rugged surface mount package compatible with high volume solder installation. Vacuum tools or other suitable pick and place equipment may be used to pick and place this part. Care should be taken to ensure that there are no voids or gaps in the solder connection so that good RF, DC and ground connections are maintained. Voids or gaps can eventually lead not only to RF performance degradation, but reduced reliability and life of the product due to thermal stress. Typical Reflow Profiles Reflow Profile Ramp Up Rate Activation Time and Temperature Time Above Melting Point Max Peak Temperature Time Within 5 C of Peak Ramp Down Rate SnPb 3-4 C/sec 60-120 sec @ 140-160 C 60-150 sec 240 C 10-20 sec 4-6 C/sec Pb Free 3-4 C/sec 60-180 sec @ 170-200 C 60-150 sec 265 C 10-20 sec 4-6 C/sec Factory Automation and Identification Mimix Designator Package Type -QU QFN (7x7mm) Component Orientation: Number of leads offered W Tape Width P1 Component Pitch P0 Hole Pitch Reel Diameter Units per Reel 28 16mm 12mm 4mm 329mm (13in) 1000 Parts are to be oriented with the PIN 1 closest to the tape's round sprocket holes on the tape's trailing edge. Note: Tape and Reel packaging is ordered with a -0N0T suffix. Package is available in 500 unit reels through designated sales channels. Minimum order quantities should be discussed with your local sales representative. Mimix Lead-Free RoHS Compliant Program - Mimix has an active program in place to meet customer and governmental requirements for eliminating lead (Pb) and other environmentally hazardous materials from our products. All Mimix RoHS compliant components are form, fit and functional replacements for their non-RoHS equivalents. Lead plating of our RoHS compliant parts is 100% matte tin (Sn) over copper alloy and is backwards compatible with current standard SnPb low-temperature reflow processes as well as higher temperature (260C reflow) "Pb Free" processes. Ordering Information Part Number for Ordering XP1080-QU-0N00 XP1080-QU-0N0T XP1080-QU-EV1 Description Ni/Au plated RoHS compliant 7x7 28L surface mount package in bulk quantity Ni/Au plated RoHS compliant 7x7 28L surface mount package in tape and reel XP1080-QU evaluation board C a u t i o n : E S D S e n s i t i ve Appropriate precautions in handling, packaging and testing devices must be observed. Proper ESD procedures should be followed when handling this device. Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099 Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com Page 6 of 6 Characteristic Data and Specifications are subject to change without notice. (c)2011 Mimix Broadband, Inc. Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept their obligation to be compliant with U.S. Export Laws.