54AC520,54ACT520
54AC520 • 54ACT520 8-Bit Identity Comparator
Literature Number: SNOS057A
54AC520 •54ACT520
8-Bit Identity Comparator
General Description
The ’AC/’ACT520 are expandable 8-bit comparators. They
compare two words of up to eight bits each and provide a
LOW output when the two words match bit for bit. The
expansion input I
A=B
also serves as an active LOW enable
input.
Features
nCompares two 8-bit words in 6.5 ns typ
nExpandable to any word length
n20-pin package
nOutputs source/sink 24 mA
n’ACT520 has TTL-compatible inputs
nStandard Microcircuit Drawing (SMD)
54AC520: 5962-90916
54ACT520: 5962-89793
Logic Symbols
Pin Names Description
A
0
–A
7
Word A Inputs
B
0
–B
7
Word B Inputs
T
A=B
Expansion or Enable Input
O
A=B
Identity Output
FACT™is a trademark of Fairchild Semiconductor Corporation.
DS100234-1
IEEE/IEC
DS100234-4
September 1998
54AC520
•
54ACT520 8-Bit Identity Comparator
© 2001 National Semiconductor Corporation DS100234 www.national.com
Connection Diagrams
Inputs Outputs
I
A=B
A, B O
A=B
L A=B
*L
LA
≠
BH
H A=B
*H
HA
≠
BH
H = HIGH Voltage Level
L = LOW Voltage Level
*A0=B
0
,A
1=B
1
,A
2=B
2
, etc.
Pin Assignment
for DIP and Flatpak
DS100234-2
Pin Assignment
for LCC
DS100234-3
54AC520
•
54ACT520
www.national.com 2
Logic Diagram
DS100234-5
Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays.
54AC520
•
54ACT520
www.national.com3
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage (V
CC
) −0.5V to +7.0V
DC Input Diode Current (I
IK
)
V
I
= −0.5V −20 mA
V
I
=V
CC
+ 0.5V +20 mA
DC Input Voltage (V
I
) −0.5V to V
CC
+ 0.5V
DC Output Diode Current (I
OK
)
V
O
= −0.5V −20 mA
V
O
=V
CC
+ 0.5V +20 mA
DC Output Voltage (V
O
) −0.5V to V
CC
+ 0.5V
DC Output Source
or Sink Current (I
O
)±50 mA
DC V
CC
or Ground Current
per Output Pin (I
CC
or I
GND
)±50 mA
Storage Temperature (T
STG
) −65˚C to +150˚C
Junction Temperature (T
J
)
CDIP 175˚C
Recommended Operating
Conditions
Supply Voltage (V
CC
)
’AC 2.0V to 6.0V
’ACT 4.5V to 5.5V
Input Voltage (V
I
) 0VtoV
CC
Output Voltage (V
O
) 0VtoV
CC
Operating Temperature (T
A
)
54AC/ACT −55˚C to +125˚C
Minimum Input Edge Rate (∆V/∆t)
’AC Devices
V
IN
from 30% to 70% of V
CC
V
CC
@3.3V, 4.5V, 5.5V 125 mV/ns
Minimum Input Edge Rate (∆V/∆t)
’ACT Devices
V
IN
from 0.8V to 2.0V
V
CC
@4.5V, 5.5V 125 mV/ns
Note 1: Absolute maximum ratings are those values beyond which damage
to the device may occur. The databook specifications should be met, without
exception, to ensure that the system design is reliable over its power supply,
temperature, and output/input loading variables. National does not recom-
mend operation of FACT™circuits outside databook specifications.
DC Characteristics for ’AC Family Devices
54AC
Symbol Parameter V
CC
T
A
= Units Conditions
(V) −55˚C to +125˚C
Guaranteed Limits
V
IH
Minimum High Level 3.0 2.1 V
OUT
= 0.1V
Input Voltage 4.5 3.15 V or V
CC
− 0.1V
5.5 3.85
V
IL
Maximum Low Level 3.0 0.9 V
OUT
= 0.1V
Input Voltage 4.5 1.35 V or V
CC
− 0.1V
5.5 1.65
V
OH
Minimum High Level 3.0 2.9 I
OUT
= −50 µA
Output Voltage 4.5 4.4 V
5.5 5.4 (Note 2)
V
IN
=V
IL
or V
IH
3.0 2.4 I
OH
= −12 mA
4.5 3.7 V I
OH
= −24 mA
5.5 4.7 I
OH
= −24 mA
V
OL
Maximum Low Level 3.0 0.1 I
OUT
=50µA
Output Voltage 4.5 0.1 V
5.5 0.1 (Note 2)
V
IN
=V
IL
or V
IH
3.0 0.50 I
OL
=12mA
4.5 0.50 V I
OL
=24mA
5.5 0.50 I
OL
=24mA
I
IN
Maximum Input 5.5 ±1.0 µA V
I
=V
CC
, GND
Leakage Current A Inputs Only
I
IH
Maximum Input 5.5 20.0 µA V
I
=V
CC
High Leakage Current B Inputs Only
54AC520
•
54ACT520
www.national.com 4
DC Characteristics for ’AC Family Devices (Continued)
54AC
Symbol Parameter V
CC
T
A
= Units Conditions
(V) −55˚C to +125˚C
Guaranteed Limits
I
IL
Maximum Input 5.5 −1.5 mA V
I
=V
CC
Low Leakage Current B Inputs Only
I
OLD
Minimum Dynamic
(Note 3) 5.5 50 mA V
OLD
= 1.65V Max
I
OHD
Output Current 5.5 −50 mA V
OHD
= 3.85V Min
I
CC
Maximum Quiescent 5.5 80.0 µA V
IN
=V
CC
Supply Current
I
CC
Maximum Quiescent 5.5 8.0 mA V
IN
= GND
Supply Current
Note 2: All outputs loaded; thresholds on input associated with output under test.
Note 3: Maximum test duration 2.0 ms, one output loaded at a time.
DC Characteristics for ’ACT Family Devices
54ACT
Symbol Parameter V
CC
T
A
= Units Conditions
(V) −55˚C to +125˚C
Guaranteed Limits
V
IH
Minimum High Level 4.5 2.0 V V
OUT
= 0.1V
Input Voltage 5.5 2.0 or V
CC
− 0.1V
V
IL
Maximum Low Level 4.5 0.8 V V
OUT
= 0.1V
Input Voltage 5.5 0.8 or V
CC
− 0.1V
V
OH
Minimum High Level 4.5 4.4 V I
OUT
= −50 µA
Output Voltage 5.5 5.4 (Note 4)
V
IN
=V
IL
or V
IH
4.5 3.70 V I
OH
= −24 mA
5.5 4.70 I
OH
= −24 mA
V
OL
Maximum Low Level 4.5 0.1 V I
OUT
=50µA
Output Voltage 5.5 0.1 (Note 4)
V
IN
=V
IL
or V
IH
4.5 0.50 V I
OL
=24mA
5.5 0.50 I
OL
=24mA
I
IN
Maximum Input 5.5 ±1.0 µA V
I
=V
CC
, GND
Leakage Current
I
IH
Maximum Input 5.5 10.0 µA V
I
=V
CC
High Leakage Current B Inputs Only
I
IL
Maximum Input 5.5 −1.0 mA V
I
=V
CC
Low Leakage Current B Inputs Only
I
CCT
Maximum 5.5 1.6 mA V
I
=V
CC
− 2.1V
I
CC
/Input
I
OLD
Minimum Dynamic
(Note 5) 5.5 50 mA V
OLD
= 1.65V Max
I
OHD
Output Current 5.5 −50 mA V
OHD
= 3.85V Min
I
CC
Maximum Quiescent 5.5 80.0 µA V
IN
=V
CC
Supply Current or GND
54AC520
•
54ACT520
www.national.com5
DC Characteristics for ’ACT Family Devices (Continued)
54ACT
Symbol Parameter V
CC
T
A
= Units Conditions
(V) −55˚C to +125˚C
Guaranteed Limits
I
CC
Maximum Quiescent 5.5 8.0 mA V
IN
= GND
Supply Current
Note 4: All outputs loaded; thresholds on input associated with output under test.
Note 5: Maximum test duration 2.0 ms, one output loaded at a time.
AC Electrical Characteristics
54AC
V
CC
T
A
= −55˚C Fig.
Symbol Parameter (V) to +125˚C Units No.
(Note 6) C
L
=50pF
Min Max
t
PLH
Propagation Delay 3.3 1.0 14.0 ns
A
n
or B
n
to O
A=B
5.0 1.5 10.5
t
PHL
Propagation Delay 3.3 1.0 15.0 ns
A
n
or B
n
to O
A=B
5.0 1.5 11.0
t
PLH
Propagation Delay 3.3 1.0 10.0 ns
I
A=B
to O
A=B
5.0 1.5 7.5
t
PHL
Propagation Delay 3.3 1.0 10.5 ns
I
A=B
to O
A=B
5.0 1.5 8.0
Note 6: Voltage Range 3.3 is 3.3V ±0.3V
Voltage Range 5.0 is 5.0V ±0.5V
AC Electrical Characteristics
54ACT
V
CC
T
A
= −55˚C Fig.
Symbol Parameter (V) to +125˚C Units No.
(Note 7) C
L
=50pF
Min Max
t
PLH
Propagation Delay 5.0 1.5 12.0 ns
A
n
or B
n
to O
A=B
t
PHL
Propagation Delay 5.0 1.5 12.0 ns
A
n
or B
n
to O
A=B
t
PLH
Propagation Delay 5.0 1.5 8.5 ns
I
A=B
to O
A=B
t
PHL
Propagation Delay 5.0 1.5 9.0 ns
I
A=B
to O
A=B
Note 7: Voltage Range 5.0 is 5.0V ±0.5V
Capacitance
Symbol Parameter Typ Units Conditions
C
IN
Input Capacitance 4.5 pF V
CC
= OPEN
C
PD
Power Dissipation Capacitance 40 pF V
CC
= 5.0V
54AC520
•
54ACT520
www.national.com 6
Applications
Ripple Expansion
DS100234-6
Parallel Expansion
DS100234-7
54AC520
•
54ACT520
www.national.com7
Physical Dimensions inches (millimeters) unless otherwise noted
20 Terminal Ceramic Leadless Chip Carrier (L)
NS Package Number E20A
20 Lead Ceramic Dual-In-Line Package (D)
NS Package Number J20A
54AC520
•
54ACT520
www.national.com 8
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Corporation
Americas
Email: support@nsc.com
National Semiconductor
Europe Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: ap.support@nsc.com
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
www.national.com
20 Lead Ceramic Flatpak (F)
NS Package Number W20A
54AC520
•
54ACT520 8-Bit Identity Comparator
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright ©2011, Texas Instruments Incorporated
