CRA12E and S Vishay Dale Thick Film, Resistor Array FEATURES * 4, 8, 10 or 16 terminal package * Choice of isolated or bussed circuits * Wrap around termination * Inner electrode protection * Flow and reflow solderable * Automatic placement capability STANDARD ELECTRICAL SPECIFICATIONS MODEL POWER RATING CRA12E & S CIRCUIT LIMITING ELEMENT TEMPERATURE TOLERANCE P70C VOLTAGE MAX COEFFICIENT W V ppm/C 0.100 01, 02, 20 0.125 03 50 RESISTANCE E-SERIES RANGE % 200 2, 5 10R - 1M0 24 - 96 100 1 10R - 1M0 24 - 96 Jumper: Zero Ohm Resistor on Request * * * * * Power rating depends on the max. temperature at the solder point , the component placement density and the substrate material Operating temperature Range: - 55C to +150C Ask aboout further value ranges Packaging: according to EIA 481 100ppm TC is standard with 1% values and 200ppm TC is standard for 5% values TECHNICAL SPECIFICATIONS PARAMETER Rated Dissipation at 70C Limiting Element Voltage1) UNIT CRA12E & S 01 / 02 / 20 CIRCUIT CRA12E & S 03 CIRCUIT W 0.1 0.125 V 50 Vdc/ac peak 100 Category Temperature Range C - 55 / + 150 Insulation Resistance > 10 9 Insulation Voltage (1min) 1)Rated voltage: PxR ORDERING INFORMATION CRA12E 04 01 MODEL TERMINAL COUNT CIRCUIT TYPE CRA12E CRA12S 04, 08, 10, 16 08, 10 01, 02, 03, 20 01, 02, 03, 20 www.vishay.com 10 105 G R-VALUE TOLERANCE % First two digits (three for 1%) F = 1% are significant. Last digit is the G = 2% multipier J = 5% Z = 0 Jumper For Technical Questions, contact: ff2aresistors@vishay.com RB8 PACKAGING Paper tape 2000pcs Document Number 31003 Revision 23-Jan-03 CRA12E and S Vishay Dale Thick Film, Resistor Array 8-Terminal device S - Version E - Version * 103 PIN 1 103 A d e MODEL PIN CRA NO# L 12E 4 2.54 12E 8 5.08 12S 8 5.08 12E 10 6.40 12S 10 6.40 12E 16 10.30 Tol - 0.15 a a e DIMENSIONS [in millimetres] A A* B B* P T 0.79 0.51 0.38 1.27 0.53 0.79 0.51 0.38 1.27 0.53 0.79 0.89 0.51 0.38 1.27 0.53 0.79 0.51 0.38 1.27 0.53 0.79 0.89 0.51 0.38 1.27 0.53 0.79 0.51 0.38 1.27 0.53 - 0.15 - 0.15 - 0.25 - 0.2 - 0.1 - 0.1 SOLDER PAD DIMENSIONS [in millimetres] W 3.05 3.05 3.05 3.05 3.05 3.05 - 0.15 c w d p a b e WAVE 2.2 4.3 0.57 1.27 0.71 1.05 1.09 REFLOW 2.2 3.9 0.57 1.27 0.71 0.86 1.09 The dimensions shown are for 8 pin part. For parts with different pin numbers use the same pitch and add or substract pads as required. CIRCUIT SCHEMATICS 02 Circuit Rated Power In % 01 Circuit 120 100 80 60 16 pin Pin 1 4 pin8 pin10 pin 03 Circuit Pin 1 4 pin 8 pin 10 pin 20 Circuit 40 20 0 - 55 -25 0 25 Derating 50 75 100 125 150 175 70 Ambient Temperature in C pin # 1 4 4 pin 8 pin 10 pin 16 pin PERFORMANCE TEST CONDITIONS OF TEST Endurance Test at 70C per EIA 575-3.14 1000 hours at 70C, 1.5 hours "ON", 0.5 hours "OFF" 1.0% Overload per EIA 575-3.6 Short time overload 2.5 x rated continuous working voltage for 5 seconds. Not to exceed 2 x max operating voltage 0.5% Thermal Shock per EIA 575-3.5 0.5% Moisture Resistance per EIA 575-3.10 1.0% Resistance to Soldering Heat EIA 575-3.8 10 seconds at 260C solder bath temperature 2.0% High Temperature Exposure per EIA 575-3.7 1.0% Low Temperature Operations per EIA 575-3.6 Solderability & Leaching EIA 575-3.12 Document Number 31003 Revision 23-Jan-03 For Technical Questions, contact: ff2aresistors@vishay.com TEST RESULTS 0.5% 95% Coverage www.vishay.com 11