High Performance Amplifier,
29 dB Gain, 10 - 200 MHz
AM-/AMC-140
FP-9
V 5.00
C-25
Absolute Maximum Ratings 1
Parameter Absolute Maximum
Max. Input Power +15 dBm
Vbias +17.0 V
Operating Temperature -55°C to +85°C
Storage Temperature -65°C to +125°C
1. Operation of this device above any one of these
paramet ers may cause permanent damange.
Pin Configuration
Pin # Function Pin # Function
1 RF OUT 6 RF IN
2 GND 7 GND
3 GND 8 GND
4 GND 9 GND
5 Vbias2 10 Vbias2
2. Bias may be applied to either a single bias pin, or bot h
bias pins. If bias is applied to both bias pins, it is impor-
tant that potenti al ground loops be avoided, and that
there is adequate filtering on the bias l i nes.
Features
+47 dBm Typical Midband Th ird Order Intercept
+28 dBm Typical Midband 1 dB Compression
5.4 dB Typical Midband Noise Figure
Description
M/A-COM’s AM-140 is a coupler feedback amplifier with
high intercept and compression points. The use of coupler
feedback minimizes noise figure and current in a high
intercept amplif ier. This amplifier is packaged in a flatpack
with flanges. Due to the internal power dissipation the
thermal rise should be minimized. The ground plane on the
PC board should be configured to remove heat from under
the package. AM-140 is ideally suited for use where a high
intercept, high reliab ility amplifier is required.
High Performance Amplifier, 29 dB Gain, 10 - 200 MHz AM-/AMC-140
Specifications subject to change without notice.
North America: Tel. (800) 366-2266
As ia /Pa c if ic: Tel.+81-44-844-8296, Fax +81-44-844-8298
Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020
Visit www.macom.com for additi onal data sheets and product information.
V 5.00
2
Electrical Specifications3,4 TA = -55°C to +85°C Case Temperature
Parameter Test Conditions Frequency Units Min. Typ. Max.
Gain 50 MHz @ +25°C 50 MHz dB 28.3 29.4 30.3
Frequency Respons e — 10 - 200 MHz dB — — ±1.2
Gain Variation with
Temperature — 10 - 200 MHz dB — — ±1.2
1 dB Compression Output Power 10 - 200 MHz
10 - 70 MHz dBm
dBm +23
+24 —
— —
—
Noise Figure — 10 - 200 MHz dB — — 7.0
Reverse Transm iss i on — 10 - 200 MHz dB — -42 -38
VSWR — 10 - 200 MHz
10 - 70 MHz Ratio
Ratio —
— —
— 2.5:1
2.0:1
Output IP2 Two-tone input s up to +10 dBm 10 - 200 MHz dBm
+52 —
— —
—
Output IP3 Two-tone input s up to +10 dBm 10 - 200 MHz
10 - 70 MHz dBm
dBm +36
+40 —
— —
—
Vbias — — V 14.25 15 15.75
Ibias Vbias = +15.0 VDC — mA — 180 220
Power Dissipation @ 15V Bias — W — 2.7 —
Typical Performan c e Curves
Intermodulation Intercept
Gain vs. Frequency
3. All specific ations appl y when operat ed at +15 V DC, with 50 ohms source and load impedance.
4. Heat Sinking: Operat i on at case temperature above 95°C is not rec ommended. Heat sinking adequate to dissipate 3.5W must
be provided in use. The flange should be screwed down to the heat sink, which shoul d be RF ground.
28.0
29.0
30.0
31.0
3 5 10 20 50 100 200 300
Frequency (MHz)
Gain (dB)
+85°C +25°C -55°C
60
62
64
66
3 5 10 20 50 100 200 300
Frequency ( MHz)
Intercept (dBm)IP2
42
44
46
48
Intercept (dBm) IP3
IP2IP3
High Performance Amplifier, 29 dB Gain, 10 - 200 MHz AM-/AMC-140
Specifications subject to change without notice.
North America: Tel. (800) 366-2266
As ia /Pa c if ic: Tel.+81-44-844-8296, Fax +81-44-844-8298
Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020
Visit www.macom.com for additi onal data sheets and product information.
V 5.00
Typical Performan c e Curves
Noise Figure and 1 dB Compression
VSWR vs. Frequency
3
Ordering Information
Part Number Package
AM-140 PIN FP-9
AMC-140 SMA C-25
1.00
1.50
2.00
2.50
3 5 10 20 50 100 200 300
Frequency (MHz)
VSWR
RF IN RF OUT
4.5
5.0
5.5
6.0
3 5 10 20 50 100 200 300
Frequency (MHz)
Noise Figure (dB)
26
27
28
29
Output Power (dBm)
Noise FigureOutput Power