The HHP650 AC-DC power supply provides upto 780 W (1000 W peak) of
output power in a robust mechanical fan-cooled package for industrial
applications. The unit comprises of a main output with voltages from 12-48
VDC and a 5 VDC standby supply which can be utilitsed with the signals and
control features of the unit to provide detection of loss of output and remote
on/off control.
• 85 V 305 VAC Input
• MILSTD810F Shock & Vibration
• 40 °C to +70 °C Operation
• SEMI F47 Compliant
• 6 kV Surge Rating IEEEStdC62.41
• UL508, ANSI/ISA 12.12.01 Class I, Div II
• Conformal Coating
• 3 Year Warranty
Dimensions:
HHP650:
9.99 x 4.20 x 2.50” (253.8 x 106.8 x 63.5 mm)
www.xppower.com
1
Models & Ratings
Output Voltage
V1
Output Current V1 Standby
Supply
Output Power V1
Model NumberNom Peak(1) Nom Peak(1)
<180 V >180 V <180 V >180 V <180 V >180 V <180 V >180 V
12 V 50.0 A --5 V / 0.2 A 607 W --HHP650PS12
15 V 40.0 A - - 5 V / 0.2 A 607 W - - HHP650PS15
24 V 27.0 A 32.5 A 33.3 A 41.7 A 5 V / 0.2 A 657 W 780 W 800 W 1000 W HHP650PS24
28 V 23.0 A 27.9 A 28.6 A 35.7 A 5 V / 0.2 A 651 W 780 W 800 W 1000 W HHP650PS28
36 V 18.0 A 21.7 A 22.2 A 27.8 A 5 V / 0.2 A 657 W 780 W 800 W 1000 W HHP650PS36
48 V 13.5 A 16.3 A 16.7 A 20.8 A 5 V / 0.2 A 657 W 780 W 800 W 1000 W HHP650PS48
VO+
Logic Connector J3
A
A
AA
A
A
C
L
VO-
1.95 (49.50)
6.31 (160.30)
2.50 (63.54)
9.99 (253.80)
Standard Terminal Block
M4 Screw 6 Pins 9.5mm Center
N
L
0.92 (23.30)
4.20 (106.77)
3.04 (77.30)
0.47 (11.90)
2.50 63.500
VR
B
LED
A Mounting hole
8 places M3 X 0.5
0.15(3.8) Max. Penetration
DETAIL B
PIN 1 PIN 2
PIN 11 PIN 12
Standard Terminal Block
M3.5 Screw 3 Pins
9.5mm Center
Mechanical Details
Notes
1. Peak Power available for 10 seconds maximum with a 35% duty cycle. The average power in a period should be equal or less than the nominal power.
HHP650 Series AC-DC Power Supplies
600/780 Watts
Input
Output
Characteristic Minimum Typical Maximum Units Notes & Conditions
Output Voltage - V1 12 48 VDC See Models and Ratings table
Initial Set Accuracy ±1 (V1) , ±5 (V Standby) % 50% load, 115/230 VAC
Output Voltage Adjustment ±10 % V1 only. See mechanical details.
Minimum Load 0A
Start Up Delay 500 ms
Hold Up Time 20 ms 90 VAC
Drift ±0.2 % After 20 min warm up
Line Regulation ±0.5 %
Load Regulation ±1 (V1) , ±5 (V Standby) % 0-100% load.
Transient Response - V1 4%
Recovery within 1% in less than 500 µs
for a 50-75%-50% load change
Ripple & Noise 1 % pk-pk V1: 20 MHz bandwidth
Overvoltage Protection 115 145 % Vnom DC. Output 1 only, recycle input to reset
Overload Protection 110 175 % Output 1 only, auto reset. See fig 1.
Short Circuit Protection Trip & restart (hiccup mode)
Overtemperature Protection 100 °C Auto reset. Input & output stage protection
Temperature Coefficient 0.05 %/˚C
Overtemperature Protection °C Protects unit from overtemperature. Auto reset.
Characteristic Minimum Typical Maximum Units Notes & Conditions
Input Voltage - Operating 85 305 VAC Derate output power 10% < 90 VAC.
Input Frequency 47 50/60 63 Hz Agency approval, 47-63 Hz
Power Factor >0.9 EN61000-3-2 class A compliant
EN61000-3-2 class C for loads ≥10%
Input Current - Full Load 6.5/3.2 A 115/230 VAC
Inrush Current 60 A 305 VAC cold start, 25 ºC
Earth Leakage Current 1.5 mA 305 VAC/60 Hz
Input Protection T16 A / 250 V internal in-line fuse
HHP Series
www.xppower.com 2
AC-DC Power Supplies
Output Overload Characteristics
Figure 1
Output Power (W)
Output Voltage (%)
Trip & Restart
0
25
50
75
100
200 400 600 800 1000 1200 1400
HHP Series
www.xppower.com
AC-DC Power Supplies
3
General
Characteristic Minimum Typical Maximum Units Notes & Conditions
Efficiency 85 % See fig. 2 & 3
Isolation: Input to Output
Input to Ground
Output to Ground
3000 VAC
2000 VAC
500 VAC
Switching Frequency
70 kHz PFC
200 kHz Main converter
130 kHz Standby
Power Density 7.4 W/in3>180 VAC
Mean Time Between Failure 177 kHrs MIL-HDBK-217F, +25 °C GB
Weight 2.8 (1.7) lb (kg)
Efficiency Vs Load
Figure 2
HHP650PS12
Figure 3
HHP650PS48
HHP Series AC-DC Power Supplies
www.xppower.com 4
Signals & Controls
Characteristic Notes & Conditions
Remote Sense Compensates for 0.5 V total voltage drop
DC OK Volt free relay contacts NO/NC (see fig.4)
Remote On/Off (Inhibit/Enable) Uncommited isolated optocoupler diode, powered diode inhibits both V1 & V2 (fan supply) (see fig.5)
Current Share
When 2 to 5 units (with the same output voltage) are used in parallel to increase output current, the current share pins 7/8 of one unit
should be connected to pins 7/8 of the other unit(s). This will force the current to share between the outputs. Similarly pins 9/11 of
each unit should also be connected as a ground reference. Units share current within 10% of each other at full load.
Standby Supply Isolated 5 V/0.2 A supply, always present when AC supplied.
DC OK
Figure 4
Figure 5
<0.8 V):
>4.5 V):
INHIBIT HI INHIBIT LOW
Inhibit Hi
Pin 6
POWER SUPPLY
100 R
800 R
2-5 mA
Chassis J3 Logic Connector
Signal High: Power Supply OFF
Low or Floating: Power Supply ON
Signal High: Power Supply ON
Low or Floating: Power Supply OFF
Inhibit Lo
Pin 5
5 V Standby
Pin 3
5 V Standby
Return Pin 1
Inhibit Hi
Pin 6
POWER SUPPLY
100 R
Chassis J3 Logic Connector
Inhibit Lo
Pin 5
5 V Standby
Pin 3
5 V Standby
Return Pin 1
800 R
2-5 mA
Remote On/Off (Inhibit)
Chassis J3 Logic Connector
POWER SUPPLY
Pin 4
Pin 10
Pin 2
NC
COM
NO
1
2
3
4
7
6
5
8
+-
HHP Series AC-DC Power Supplies
55www.xppower.com
Environmental
Characteristic Minimum Typical Maximum Units Notes & Conditions
Operating Temperature -40 +70 °C See derating curve, fig.6
Storage Temperature -40 +85 °C Some specification parameters maybe exceeded
until after 20 minutes warm up period.
Cooling Forced-cooled via integral dual voltage level fan,
which is load dependant. See fig.7
Humidity 95 %RH Non-condensing
Operating Altitude 5000 m
Shock 30 g pk, half sine, 6 axes EN60068-2-27, -2-47
& MIL-STD-810F 514.5 cat 4
Vibration 2 g rms, 5-500 kHz, 3 axes EN60068-2-6 & MIL-
STD-810F 516.5 cat 1
-40 -20 0 +70+50
50
100
Ambient Temperature (ºC)
Some specification
parameters may not be met
Output Load (%)
0
Figure 6
Temperature Derating Curve
0
50
0
Fan Speed (%)
100
25 50 75 100
Output Power (%)
Figure 7
Fan Speed Control
EMC: Immunity
Phenomenon Standard Test Level Criteria Notes & Conditions
Voltage Fluctuations EN61000-3-3
Low Voltage PSU EMC EN61204-3 High severity level as below
ESD Immunity EN61000-4-2 3A
Radiated Immunity EN61000-4-3 3A
EFT/Burst EN61000-4-4 3A
Surges EN61000-4-5 Installation class 3 A
IEEEStdC62.41-loc cat C1 6kV, 3 kA
Conducted EN61000-4-6 3A
Dips and Interruptions
EN55024 (100 VAC)
Dip >95% (0 VAC), 8.3 ms A
Dip 30% (70 VAC), 416 ms B
Dip >95% (0 VAC), 4160 ms B
EN55024 (240 VAC)
Dip >95% (0 VAC), 10.0 ms A
Dip 30% (70 VAC), 500 ms B
Dip >95% (0 VAC), 5000 ms B
SEMI F47 Compliant
EMC: Emissions
Phenomenon Standard Test Level Criteria Notes & Conditions
Conducted EN55011/22 Class B
Radiated EN55011/22 Class A
Harmonic Current EN61000-3-2 Class A
HHP Series AC-DC Power Supplies
www.xppower.com 24Feb14
Mechanical Details
VO+
Logic Connector J3
A
A
AA
A
A
C
L
VO-
1.95 (49.50)
6.31 (160.30)
2.50 (63.54)
9.99 (253.80)
Standard Terminal Block
M4 Screw 6 Pins 9.5mm Center
N
L
0.92 (23.30)
4.20 (106.77)
3.04 (77.30)
0.47 (11.90)
2.50 63.500
VR
B
LED
A Mounting hole
8 places M3 X 0.5
0.15(3.8) Max. Penetration
DETAIL B
PIN 1 PIN 2
PIN 11 PIN 12
Standard Terminal Block
M3.5 Screw 3 Pins
9.5mm Center
1. Dimensions shown in inches (mm).
2. Weight: 2.8 lb (1.27 kg).
3. J1 Mating Plug: JST part no. PHR-2, contact: JST part no. SPH-002T-P0.5S;
J2 Mating Plug: JST part no. PHDR-10VS, contact: 26-22AWG JST part no. SPHD-001T-P0.5
Notes
J3 Logic Connector
(JST S12B-PHDSS)
Pin Function
1 5 V Standby Return
2 NO (Relay)
3 +5 V Standby
4 N.C (Relay)
5 - Inhibit
6 +Inhibit
7 Current Share
8 Current Share
9 - Sense / Signal GND
10 COM (Relay)
11 - Sense / Signal GND
12 +Sense
Safety Approvals
Safety Agency Safety Standard Notes & Conditions
CB Report IEC60950-1:2005 + A1:2009 Information Technology
UL
UL60950-1 (2011), CSA 22.2 No.60950-1 Information Technology
UL508, CSA 22.2 No. 107.1-01 Industrial Control Equipment
ANSI/ISA 12.12.01-2000 Hazardous Locations
TUV EN60950-1 A12:2011 Information Technology
CE LVD & RoHS
Equipment Protection Class Class I See safety agency conditions of acceptibility for details