a~í~=pÜÉÉía~í~=pÜÉÉí
¤EPCOS AG 2015. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS’ prior express consent is prohibited.
EPCOS AG is a TDK Group Company.
Inductors
Transponder coils
Size 11.4 u 3.5 u 2.4 (mm)
Series/Type: B82450A*A
Date: October 2015
210/15
Please read Cautions and warnings and
Important notes at the end of this document.
Rated inductance 1 ... 7.2 mH
Sensitivity 16 ... 52 mV/µT
Construction
Ferrite core
Winding: enamel copper wire welded to terminals
Flame-retardant molding
Features
Robust construction for a high mechanical stability
Qualified to AEC-Q200
High sensitivity in X/Y orientation
Suitable for pick and place
and AOI (Automatic Optical Inspection)
Suitable for lead-free reflow soldering
as referenced in JEDEC J-STD 020D
RoHS-compatible
Applications
Car access systems
immobilizer
PEPS (Passive Entry, Passive Start)
TPMS (Tire Pressure Monitoring Systems)
Terminals
Base material CuSn6
Layer composition Ni, Sn (lead-free)
Electro-plated
Marking
Marking on component:
Manufacturer, L value (nH, coded), letter “A”, date of
manufacture (YWWD), last five digits of lot number,
internal information
Minimum data on reel:
Manufacturer, ordering code, L value, quantity, date of packing
Delivery mode and packing unit
24-mm blister tape, wound on 330-mm reel
Packing unit: 2500 pcs./reel
B82450A*ATransponder coils
Size 11.4 x 3.5 x 2.4 (mm)
310/15
Please read Cautions and warnings and
Important notes at the end of this document.
Dimensional drawing and layout recommendation
Dimensions in mm
Taping and packing
Blister tape Reel
Dimensions in mm
B82450A*ATransponder coils
Size 11.4 x 3.5 x 2.4 (mm)
410/15
Please read Cautions and warnings and
Important notes at the end of this document.
Technical data and measuring conditions
Characteristics and ordering codes
Characteristics and ordering codes for other L values available on request.
Rated inductance LRMeasured with Agilent 4294A and test fixture Agilent 16034
at frequency fL, RMS voltage 500 mV, +20 °C
Q factor Qmin Measured with Agilent 4294A and test fixture Agilent 16034
at frequency fQ, RMS voltage 500 mV, +20 °C
Sensitivity Styp Measured with Helmholtz coil test setup at 125 kHz
Resonance frequency fres Measuring with network analyzer Agilent 8753D, +20 °C
Solderability (lead-free) Sn95.5Ag3.8Cu0.7: +(245 r5) °C, 3 s
Wetting of soldering area t90%
(based on IEC 60068-2-58)
Resistance to soldering heat +260 °C, 40 s (as referenced in JEDEC J-STD 020D)
Climatic category 40/125/56 (to IEC 60068-1)
Storage conditions Mounted: 40 °C … +125 °C
Packaged: –25 °C … +40 °C, d75% RH
Weight Approx. 0.32 g
LR
mH
L
tolerance
fL, fQ
kHz
Qmin Styp fres
MHz
Ordering code
1.0 r3% 125 40 16 > 3.5 B82450A1004A000
2.36 125 50 30 > 2.0 B82450A2364A000
4.9 125 40 41 > 1.2 B82450A4904A000
7.2 125 40 52 > 1.0 B82450A7204A000
mV
PT
B82450A*ATransponder coils
Size 11.4 x 3.5 x 2.4 (mm)
510/15
Cautions and warnings
Please note the recommendations in our Inductors data book (latest edition) and in the data
sheets.
Particular attention should be paid to the derating curves given there.
The soldering conditions should also be observed. Temperatures quoted in relation to wave
soldering refer to the pin, not the housing.
If the components are to be washed varnished it is necessary to check whether the washing
varnish agent that is used has a negative effect on the wire insulation, any plastics that are used,
or on glued joints. In particular, it is possible for washing varnish agent residues to have a
negative effect in the long-term on wire insulation.
Washing processes may damage the product due to the possible static or cyclic mechanical
loads (e.g. ultrasonic cleaning). They may cause cracks to develop on the product and its parts,
which might lead to reduced reliability or lifetime.
The following points must be observed if the components are potted in customer applications:
Many potting materials shrink as they harden. They therefore exert a pressure on the plastic
housing or core. This pressure can have a deleterious effect on electrical properties, and in
extreme cases can damage the core or plastic housing mechanically.
It is necessary to check whether the potting material used attacks or destroys the wire
insulation, plastics or glue.
The effect of the potting material can change the high-frequency behaviour of the components.
Ferrites are sensitive to direct impact. This can cause the core material to flake, or lead to
breakage of the core.
Even for customer-specific products, conclusive validation of the component in the circuit can
only be carried out by the customer.
Display of ordering codes for EPCOS products
The ordering code for one and the same product can be represented differently in data sheets,
data books, other publications and the website of EPCOS, or in order-related documents such as
shipping notes, order confirmations and product labels. The varying representations of the
ordering codes are due to different processes employed and do not affect the
specifications of the respective products. Detailed information can be found on the Internet
under www.epcos.com/orderingcodes.
Please read Cautions and warnings and
Important notes at the end of this document.
610/15
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application. As
a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in which
the malfunction or failure of an electronic component could endanger human life or health (e.g.
in accident prevention or life-saving systems), it must therefore be ensured by means of suitable
design of the customer application or other action taken by the customer (e.g. installation of
protective circuitry or redundancy) that no injury or damage is sustained by third parties in the
event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products.
Consequently, we cannot guarantee that all products named in this publication will always be
available. The aforementioned does not apply in the case of individual agreements deviating
from the foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version
of the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, Alu-X, CeraDiode, CeraLink, CeraPad, CeraPlas, CSMP, CSSP,
CTVS, DeltaCap, DigiSiMic, DSSP, ExoCore, FilterCap, FormFit, LeaXield, MiniBlue, MiniCell,
MKD, MKK, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, PQSine, SIFERRIT,
SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, TFAP,
ThermoFuse, WindCap are trademarks registered or pending in Europe and in other
countries. Further information will be found on the Internet at www.epcos.com/trademarks.