LM3420-4.2, -8.2, -8.4, -12.6, -16.8 Lithium-Ion Battery Charge Controller General Description The LM3420 series of controllers are monolithic integrated circuits designed for charging and end-of-charge control for Lithium-Ion rechargeable batteries. The LM3420 is available in five fixed voltage versions for one through four cell charger applications (4.2V, 8.2V/8.4V, 12.6V and 16.8V respectively). Included in a very small package is an (internally compensated) op amp, a bandgap reference, an NPN output transistor, and voltage setting resistors. The amplifier's inverting input is externally accessible for loop frequency compensation. The output is an open-emitter NPN transistor capable of driving up to 15 mA of output current into external circuitry. A trimmed precision bandgap reference utilizes temperature drift curvature correction for excellent voltage stability over the operating temperature range. Available with an initial tolerance of 0.5% for the A grade version, and 1% for the standard version, the LM3420 allows for precision end-of-charge control for Lithium-Ion rechargeable batteries. The LM3420 is available in a sub-miniature 5-lead SOT23-5 surface mount package thus allowing very compact designs. Features n n n n n Voltage options for charging 1, 2, 3 or 4 cells Tiny SOT23-5 package Precision (0.5%) end-of-charge control Drive capability for external power stage Low quiescent current, 85 A (typ.) Applications n Lithium-Ion battery charging n Suitable for linear and switching regulator charger designs Typical Application and Functional Diagram DS012359-1 Typical Constant Current/Constant Voltage Li-Ion Battery Charger DS012359-2 LM3420 Functional Diagram SIMPLE SWITCHER (R) is a registered trademark of National Semiconductor Corporation. (c) 2000 National Semiconductor Corporation DS012359 www.national.com LM3420-4.2, -8.2, -8.4, -12.6, -16.8 Lithium-Ion Battery Charge Controller July 2000 LM3420-4.2/LM3420-8.2/LM3420-8.4/LM3420-12.6/LM3420-16.8 Connection Diagrams and Order Information 5-Lead Small Outline Package (M5) Actual Size DS012359-4 DS012359-3 *No internal connection, but should be soldered to PC board for best heat transfer. Top View For Ordering Information See Figure 1 in this Data Sheet See NS Package Number MF05A www.national.com 2 ESD Susceptibility (Note 3) Human Body Model 1500V See AN-450 "Surface Mounting Methods and Their Effect on Product Reliability" for methods on soldering surface-mount devices. If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Input Voltage V(IN) Output Current Junction Temperature Storage Temperature Lead Temperature Vapor Phase (60 seconds) Infrared (15 seconds) Power Dissipation (TA = 25C) (Note 2) 20V 20 mA 150C -65C to +150C Operating Ratings (Notes 1, 2) Ambient Temperature Range Junction Temperature Range Output Current +215C +220C -40C TA +85C -40C TJ +125C 15 mA 300 mW LM3420-4.2 Electrical Characteristics Specifications with standard type face are for TJ = 25C, and those with boldface type apply over full Operating Temperature Range. Unless otherwise specified, V(IN) = VREG, VOUT = 1.5V. Symbol VREG Parameter Regulation Voltage Regulation Voltage Conditions IOUT = 1 mA Typical LM3420A-4.2 LM3420-4.2 Units (Note 4) Limit Limit (Limits) (Note 5) (Note 5) 4.221/4.242 4.242/4.284 4.179/4.158 4.158/4.116 V(min) 0.5/ 1 1/ 2 %(max) 4.2 IOUT = 1 mA V V(max) Tolerance Iq Quiescent Current IOUT = 1 mA 85 Gm Transconductance 20 A IOUT 1 mA 3.3 IOUT/VREG VOUT = 2V 1 mA IOUT 15 mA Voltage Gain 1V VOUT VREG - 1.2V (-1.3) VOUT/VREG RL = 200 (Note 6) 1V VOUT VREG - 1.2V (-1.3) Output Saturation (Note 7) IOUT = 15 mA IL Output Leakage V(IN) = VREG -100 mV Current VOUT = 0V Rf V(IN) = VREG +100 mV 1.3/0.75 1.0/0.50 mA/mV(min) 3.0/1.5 2.5/1.4 mA/mV(min) 550/250 450/200 V/V(min) 1500/900 1000/700 V/V(min) mA/mV mA/mV V/V V/V 1.0 V 1.2/1.3 1.2/1.3 V(max) 0.5/1.0 0.5/1.0 A(max) 94 94 k(max) 56 56 k(min) 0.1 Internal Feedback Output Noise A(max) 3500 A 75 Resistor (Note 8) En 125/150 1000 RL = 2 k VSAT 110/115 6.0 VOUT = 2V AV A IOUT = 1 mA, 10 Hz f 10 kHz 70 k VRMS Voltage 3 www.national.com LM3420-4.2/LM3420-8.2/LM3420-8.4/LM3420-12.6/LM3420-16.8 Absolute Maximum Ratings (Note 1) LM3420-4.2/LM3420-8.2/LM3420-8.4/LM3420-12.6/LM3420-16.8 LM3420-8.2 Electrical Characteristics Specifications with standard type face are for TJ = 25C, and those with boldface type apply over full Operating Temperature Range. Unless otherwise specified, V(IN) = VREG, VOUT = 1.5V. Symbol VREG Parameter Regulation Voltage Regulation Voltage Conditions IOUT = 1 mA Typical LM3420A-8.2 LM3420-8.2 Units (Note 4) Limit Limit (Limits) (Note 5) (Note 5) 8.241/8.282 8.282/8.364 8.159/8.118 8.118/8.036 V(min) 0.5/ 1 1/ 2 %(max) 110/115 125/150 A(max) 1.3/0.75 1.0/0.50 mA/mV(min) 3.0/1.5 2.5/1.4 mA/mV(min) 550/250 450/200 V/V(min) 8.2 IOUT = 1 mA V V(max) Tolerance Iq Quiescent Current Gm IOUT = 1 mA Transconductance 20 A IOUT 1 mA IOUT/VREG VOUT = 6V 85 3.3 1 mA IOUT 15 mA Voltage Gain 1V VOUT VREG - 1.2V (-1.3) VOUT/VREG RL = 470 (Note 6) 1V VOUT VREG - 1.2V (-1.3) IL Rf Output Saturation V(IN) = VREG +100 mV (Note 7) IOUT = 15 mA Output Leakage V(IN) = VREG -100 mV Current VOUT = 0V V/V 1500/900 1000/700 V/V(min) 1.2/1.3 1.2/1.3 V(max) 0.5/1.0 0.5/1.0 A(max) 220 220 k(max) 132 132 k(min) 1.0 V 0.1 Internal Feedback Output Noise V/V 3500 A 176 Resistor (Note 8) En mA/mV 1000 RL = 5 k VSAT mA/mV 6.0 VOUT = 6V AV A IOUT = 1 mA, 10 Hz f 10 kHz k 140 VRMS Voltage LM3420-8.4 Electrical Characteristics Specifications with standard type face are for TJ = 25C, and those with boldface type apply over full Operating Temperature Range. Unless otherwise specified, V(IN) = VREG, VOUT = 1.5V. Symbol VREG Parameter Regulation Voltage Regulation Voltage Conditions IOUT = 1 mA Typical LM3420A-8.4 LM3420-8.4 Units (Note 4) Limit Limit (Limits) (Note 5) (Note 5) 8.442/8.484 8.484/8.568 V(max) 8.358/8.316 8.316/8.232 V(min) 0.5/ 1 1/ 2 %(max) 8.4 IOUT = 1 mA V Tolerance Iq Quiescent Current IOUT = 1 mA 85 Gm Transconductance 20 A IOUT 1 mA 3.3 IOUT/VREG VOUT = 6V 1 mA IOUT 15 mA 110/115 125/150 A(max) 1.3/0.75 1.0/0.50 mA/mV(min) mA/mV 6.0 VOUT = 6V www.national.com A mA/mV 3.0/1.5 4 2.5/1.4 mA/mV(min) (Continued) Specifications with standard type face are for TJ = 25C, and those with boldface type apply over full Operating Temperature Range. Unless otherwise specified, V(IN) = VREG, VOUT = 1.5V. Symbol AV Parameter Conditions Voltage Gain 1V VOUT VREG - 1.2V (-1.3) VOUT/VREG RL = 470 (Note 6) 1V VOUT VREG - 1.2V (-1.3) Typical LM3420A-8.4 LM3420-8.4 Units (Note 4) Limit Limit (Limits) (Note 5) (Note 5) 1000 IL Rf Output Saturation V(IN) = VREG +100 mV (Note 7) IOUT = 15 mA Output Leakage V(IN) = VREG -100 mV Current VOUT = 0V V/V(min) 1500/900 1000/700 V/V(min) 1.2/1.3 1.2/1.3 V(max) 0.5/1.0 0.5/1.0 A(max) 227 227 k(max) 135 135 k(min) V/V V 0.1 Internal Feedback Output Noise 450/200 1.0 A 181 Resistor (Note 8) En 550/250 3500 RL = 5 k VSAT V/V IOUT = 1 mA, 10 Hz f 10 kHz k 140 VRMS Voltage LM3420-12.6 Electrical Characteristics Specifications with standard type face are for TJ = 25C, and those with boldface type apply over full Operating Temperature Range. Unless otherwise specified, V(IN) = VREG, VOUT = 1.5V. Symbol VREG Parameter Regulation Voltage Regulation Voltage Conditions IOUT = 1 mA Typical LM3420A-12.6 LM3420-12.6 Units (Note 4) Limit Limit (Limits) (Note 5) (Note 5) 12.6 IOUT = 1 mA V 12.663/12.726 12.726/12.852 12.537/12.474 12.474/12.348 V(max) V(min) 0.5/ 1 1/ 2 %(max) 110/115 125/150 A(max) 1.3/0.75 1.0/0.5 mA/mV(min) 3.0/1.5 2.5/1.4 mA/mV(min) 550/250 450/200 V/V(min) Tolerance Iq Gm Quiescent Current IOUT = 1 mA Transconductance 20 A IOUT 1 mA IOUT/VREG VOUT = 10V 85 3.3 1 mA IOUT 15 mA Voltage Gain 1V VOUT VREG - 1.2V (-1.3) VOUT/VREG RL = 750 (Note 6) 1V VOUT VREG - 1.2V (-1.3) Output Saturation V(IN) = VREG +100 mV (Note 7) IOUT = 15 mA IL Output Leakage V(IN) = VREG -100 mV Current VOUT = 0V Rf Internal Feedback Output Noise Voltage V/V 3500 V/V 1500/900 1000/700 V/V(min) 1.2/1.3 1.2/1.3 V(max) 1.0 V 0.1 A 0.5/1.0 0.5/1.0 A(max) 359 359 k(max) 215 215 k(min) 287 Resistor (Note 8) En mA/mV 1000 RL = 10 k VSAT mA/mV 6.0 VOUT = 10V AV A IOUT = 1 mA, 10 Hz f 10 kHz 5 210 k VRMS www.national.com LM3420-4.2/LM3420-8.2/LM3420-8.4/LM3420-12.6/LM3420-16.8 LM3420-8.4 Electrical Characteristics LM3420-4.2/LM3420-8.2/LM3420-8.4/LM3420-12.6/LM3420-16.8 LM3420-16.8 Electrical Characteristics Specifications with standard type face are for TJ = 25C, and those with boldface type apply over full Operating Temperature Range. Unless otherwise specified, V(IN) = VREG, VOUT = 1.5V. Symbol VREG Parameter Regulation Voltage Regulation Voltage Conditions IOUT = 1 mA Typical LM3420A-16.8 LM3420-16.8 Units (Note 4) Limit Limit (Limits) (Note 5) (Note 5) 16.884/16.968 16.968/17.136 16.716/16.632 16.632/16.464 V(min) 0.5/ 1 1/ 2 %(max) 110/115 125/150 A(max) 0.8/0.4 0.7/0.35 mA/mV(min) 2.9/0.9 2.5/0.75 mA/mV(min) 550/250 450/200 V/V(min) 16.8 V IOUT = 1 mA V(max) Tolerance Iq Quiescent Current Gm IOUT = 1 mA Transconductance 20 A IOUT 1 mA IOUT/VREG VOUT = 15V 85 3.3 1 mA IOUT 15 mA Voltage Gain 1V VOUT VREG - 1.2V (-1.3) VOUT/VREG RL = 1 k (Note 6) 1V VOUT VREG - 1.2V (-1.3) IL Rf Output Saturation V(IN) = VREG +100 mV (Note 7) IOUT = 15 mA Output Leakage V(IN) = VREG -100 mV Current VOUT = 0V V/V 1200/750 1000/650 V/V(min) 1.2/1.3 1.2/1.3 V(max) 0.5/1.0 0.5/1.0 A(max) 490 490 k(max) 294 294 k(min) 1.0 V 0.1 Internal Feedback Output Noise Voltage V/V 3500 A 392 Resistor (Note 8) En mA/mV 1000 RL = 15 k VSAT mA/mV 6.0 VOUT = 15V AV A IOUT = 1 mA, 10 Hz f 10 kHz k 280 VRMS Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 2: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax (maximum junction temperature), JA (junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any temperature is PDmax = (TJmax - TA)/JA or the number given in the Absolute Maximum Ratings, whichever is lower. The typical thermal resistance (JA) when soldered to a printed circuit board is approximately 306C/W for the M5 package. Note 3: The human body model is a 100 pF capacitor discharged through a 1.5 k resistor into each pin. Note 4: Typical numbers are at 25C and represent the most likely parametric norm. Note 5: Limits are 100% production tested at 25C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control (SQC) methods. The limits are used to calculate National's Averaging Outgoing Quality Level (AOQL). Note 6: Actual test is done using equivalent current sink instead of a resistor load. Note 7: VSAT = V(IN) - VOUT, when the voltage at the IN pin is forced 100 mV above the nominal regulating voltage (VREG). Note 8: See Applications and Typical Performance Characteristics sections for information on this resistor. www.national.com 6 4.2V Bode Plot Response Time for 4.2V Version Response Time for 4.2V Version DS012359-17 8.2V and 8.4V Bode Plot DS012359-18 Response Time for 8.2V, 8.4V Versions DS012359-20 12.6V Bode Plot Response Time for 8.2V, 8.4V Versions DS012359-21 Response Time for 12.6V Version DS012359-22 Response Time for 12.6V Version DS012359-23 16.8V Bode Plot DS012359-19 DS012359-24 Response Time for 16.8V Version DS012359-25 Response Time for 16.8V Version DS012359-26 DS012359-27 7 DS012359-28 www.national.com LM3420-4.2/LM3420-8.2/LM3420-8.4/LM3420-12.6/LM3420-16.8 Typical Performance Characteristics LM3420-4.2/LM3420-8.2/LM3420-8.4/LM3420-12.6/LM3420-16.8 Typical Performance Characteristics Regulation Voltage vs Output Voltage and Load Resistance (Continued) Circuit Used for Bode Plots Circuit Used for Response Time DS012359-30 DS012359-31 DS012359-29 Regulation Voltage vs Output Voltage and Load Resistance Internal Feedback Resistor (Rf) Tempco Quiescent Current DS012359-33 DS012359-32 Regulation Voltage vs Output Voltage and Load Resistance DS012359-34 Normalized Temperature Drift Output Saturation Voltage (VSAT) DS012359-36 DS012359-35 www.national.com 8 DS012359-37 LM3420-4.2/LM3420-8.2/LM3420-8.4/LM3420-12.6/LM3420-16.8 Typical Performance Characteristics (Continued) Regulation Voltage vs Output Voltage and Load Resistance DS012359-38 9 www.national.com LM3420-4.2/LM3420-8.2/LM3420-8.4/LM3420-12.6/LM3420-16.8 Five Lead Surface Mount Package Information The small SOT23-5 package allows only 4 alphanumeric characters to identify the product. The table below contains the field information marked on the package. Voltage Grade Order Package Information Marking Supplied as 4.2V A (Prime) LM3420AM5-4.2 D02A 1000 unit increments on tape and reel 4.2V A (Prime) LM3420AM5X-4.2 D02A 3000 unit increments on tape and reel 4.2V B (Standard) LM3420M5-4.2 D02B 1000 unit increments on tape and reel 4.2V B (Standard) LM3420M5X-4.2 D02B 3000 unit increments on tape and reel 8.2V A (Prime) LM3420AM5-8.2 D07A 1000 unit increments on tape and reel 8.2V A (Prime) LM3420AM5X-8.2 D07A 3000 unit increments on tape and reel 8.2V B (Standard) LM3420M5-8.2 D07B 1000 unit increments on tape and reel 8.2V B (Standard) LM3420M5X-8.2 D07B 3000 unit increments on tape and reel 8.4V A (Prime) LM3420AM5-8.4 D03A 1000 unit increments on tape and reel 8.4V A (Prime) LM3420AM5X-8.4 D03A 3000 unit increments on tape and reel 8.4V B (Standard) LM3420M5-8.4 D03B 1000 unit increments on tape and reel 8.4V B (Standard) LM3420M5X-8.4 D03B 3000 unit increments on tape and reel 12.6V A (Prime) LM3420AM5-12.6 D04A 1000 unit increments on tape and reel 12.6V A (Prime) LM3420AM5X-12.6 D04A 3000 unit increments on tape and reel 12.6V B (Standard) LM3420M5-12.6 D04B 1000 unit increments on tape and reel 12.6V B (Standard) LM3420M5X-12.6 D04B 3000 unit increments on tape and reel 16.8V A (Prime) LM3420AM5-16.8 D05A 1000 unit increments on tape and reel 16.8V A (Prime) LM3420AM5X-16.8 D05A 3000 unit increments on tape and reel 16.8V B (Standard) LM3420M5-16.8 D05B 1000 unit increments on tape and reel 16.8V B (Standard) LM3420M5X-16.8 D05B 3000 unit increments on tape and reel FIGURE 1. SOT23-5 Marking The first letter "D" identifies the part as a Driver, the next two numbers indicate the voltage, "02" for a 4.2V part, "07" for an 8.2V part, "03" for an 8.4V part, "04" for a 12.6V part, and "05" for a 16.8V part. The fourth letter indicates the grade, "B" for standard grade, "A" for the prime grade. The SOT23-5 surface mount package is only available on tape in quantity increments of 1000 on tape and reel (indicated by the letters "M5" in the part number), or in quantity increments of 3000 on tape and reel (indicated by the letters "M5X" in the part number). single capacitor (CC) connected from the compensation pin to the out pin of the LM3420. The capacitor values shown in the schematics are adequate under most conditions, but they can be increased or decreased depending on the desired loop response. Applying a load pulse to the output of a regulator circuit and observing the resultant output voltage response is an easy method of determining the stability of the control loop. Analyzing more complex feedback loops requires additional information. The formula for AC gain at a frequency (f) is as follows; Product Description The LM3420 is a shunt regulator specifically designed to be the reference and control section in an overall feedback loop of a Lithium-Ion battery charger. The regulated output voltage is sensed between the IN pin and GROUND pin of the LM3420. If the voltage at the IN pin is less than the LM3420 regulating voltage (VREG), the OUT pin sources no current. As the voltage at the IN pin approaches the VREG voltage, the OUT pin begins sourcing current. This current is then used to drive a feedback device (opto-coupler), or a power device (linear regulator, switching regulator, etc.), which servos the output voltage to be the same value as VREG. In some applications, (even under normal operating conditions) the voltage on the IN pin can be forced above the VREG voltage. In these instances, the maximum voltage applied to the IN pin should not exceed 20V. In addition, an external resistor may be required on the OUT pin to limit the maximum current to 20 mA. where Rf 75 k for the 4.2V part, Rf 181 k for the 8.4V part, Rf 287 k for the 12.6V part, and Rf 392 k for the 16.8V part. The resistor (Rf) in the formula is an internal resistor located on the die. Since this resistor value will affect the phase margin, the worst case maximum and minimum values are im- Compensation The inverting input of the error amplifier is brought out to allow overall closed-loop compensation. In many of the applications circuits shown here, compensation is provided by a www.national.com 10 Test Circuit (Continued) The test circuit shown in Figure 2 can be used to measure and verify various LM3420 parameters. Test conditions are set by forcing the appropriate voltage at the VOUT Set test point and selecting the appropriate RL or IOUT as specified in the Electrical Characteristics section. Use a DVM at the "measure" test points to read the data. portant when analyzing closed loop stability. The minimum and maximum room temperature values of this resistor are specified in the Electrical Characteristics section of this data sheet, and a curve showing the temperature coefficient is shown in the curves section. Minimum values of Rf result in lower phase margins. DS012359-7 FIGURE 2. LM3420 Test Circuit VREG External Voltage Trim The regulation voltage (VREG) of the LM3420 can be externally trimmed by adding a single resistor from the COMP pin to the +IN pin or from the COMP pin to the GND pin, depending on the desired trim direction. Trim adjustments up to 10% of VREG can be realized, with only a small increase in the temperature coefficient. (See temperature coefficient curve shown in Figure 3 below.) DS012359-9 Increasing VREG DS012359-10 Decreasing VREG FIGURE 4. Changing VREG Formulas for selecting trim resistor values are shown below, based on the percent of increase (%incr) or percent of decrease (%decr) of the output voltage from the nominal voltage. For LM3420-4.2 Rincrease = 22x105/%incr DS012359-8 Normalized Temperature Drift with Output Externally Trimmed Rdecrease = (53x105/%decr) - 75x103 For LM3420-8.2 11 www.national.com LM3420-4.2/LM3420-8.2/LM3420-8.4/LM3420-12.6/LM3420-16.8 Compensation LM3420-4.2/LM3420-8.2/LM3420-8.4/LM3420-12.6/LM3420-16.8 VREG External Voltage Trim cuits shown are designed for 2 cell operation, but they can readily be changed for either 1, 3 or 4 cell charging applications. (Continued) Rincrease = 26x105/%incr Rdecrease = (150x105/%decr) - 176x103 One item to keep in mind when designing with the LM3420 is that there are parasitic diodes present. In some designs, under special electrical conditions, unwanted currents may flow. Parasitic diodes exist from OUT to IN, as well as from GROUND to IN. In both instances the diode arrow is pointed toward the IN pin. For LM3420-8.4 Rincrease = 26x105/%incr Rdecrease = (154x105/%decr) - 181x103 For LM3420-12.6 Rincrease = 28x105/%incr Rdecrease = (259x105/%decr) - 287x103 Application Circuits For LM3420-16.8 Rincrease = 29x105/%incr Rdecrease = (364x105/%decr) - 392x103 The circuit shown in Figure 5 performs constant-current, constant-voltage charging of two Li-Ion cells. At the beginning of the charge cycle, when the battery voltage is less than 8.4V, the LM3420 sources no current from the OUT pin, keeping Q2 off, thus allowing the LM317 Adjustable voltage regulator to operate as a constant-current source. (The LM317 is rated for currents up to 1.5A, and the LM350 and LM338 can be used for higher currents.) The LM317 forces a constant 1.25V across RLIM, thus generating a constant current of Application Information The LM3420 regulator/driver provides the reference and feedback drive functions for a Lithium-Ion battery charger. It can be used in many different charger configurations using both linear and switching topologies to provide the precision needed for charging Lithium-Ion batteries safely and efficiently. Output voltage tolerances better than 0.5% are possible without using trim pots or precision resistors. The cir- ILIM = 1.25V/RLIM DS012359-1 FIGURE 5. Constant Current/Constant Voltage Li-Ion Battery Charger DS012359-11 FIGURE 6. Low Drop-Out Constant Current/Constant Voltage 2-Cell Charger (approximately 5 mV). Diode D1 is also used to prevent the battery current from flowing through the LM317 regulator from the output to the input when the DC input voltage is removed. As the battery charges, its voltage begins to rise, and is sensed at the IN pin of the LM3420. Once the battery voltage reaches 8.4V, the LM3420 begins to regulate and starts sourcing current to the base of Q2. Transistor Q2 begins Transistor Q1 provides a disconnect between the battery and the LM3420 when the input voltage is removed. This prevents the 85 A quiescent current of the LM3420 from eventually discharging the battery. In this application Q1 is used as a low offset saturated switch, with the majority of the base drive current flowing through the collector and crossing over to the emitter as the battery becomes fully charged. It provides a very low collector to emitter saturation voltage www.national.com 12 stage of the LM10C will disconnect the battery from the charger circuit when the input supply voltage is removed to prevent the battery from discharging. (Continued) controlling the ADJ. pin of the LM317 which begins to regulate the voltage across the battery and the constant voltage portion of the charging cycle starts. Once the charger is in the constant voltage mode, the charger maintains a regulated 8.4V across the battery and the charging current is dependent on the state of charge of the battery. As the cells approach a fully charged condition, the charge current falls to a very low value. Figure 6 shows a Li-Ion battery charger that features a dropout voltage of less than one volt. This charger is a constant-current, constant-voltage charger (it operates in constant-current mode at the beginning of the charge cycle and switches over to a constant-voltage mode near the end of the charging cycle). The circuit consists of two basic feedback loops. The first loop controls the constant charge current delivered to the battery, and the second determines the final voltage across the battery. With a discharged battery connected to the charger, (battery voltage is less than 8.4V) the circuit begins the charge cycle with a constant charge current. The value of this current is set by using the reference section of the LM10C to force 200 mV across R7 thus causing approximately 100 A of emitter current to flow through Q1, and approximately 1 mA of emitter current to flow through Q2. The collector current of Q1 is also approximately 100 A, and this current flows through R2 developing 50 mV across it. This 50 mV is used as a reference to develop the constant charge current through the current sense resistor R1. The constant current feedback loop operates as follows. Initially, the emitter and collector current of Q2 are both approximately 1 mA, thus providing gate drive to the MOSFET Q3, turning it on. The output of the LM301A op-amp is low. As Q3's current reaches 1A, the voltage across R1 approaches 50 mV, thus canceling the 50 mV drop across R2, and causing the op-amp's output to start going positive, and begin sourcing current into R8. As more current is forced into R8 from the op-amp, the collector current of Q2 is reduced by the same amount, which decreases the gate drive to Q3, to maintain a constant 50 mV across the 0.05 current sensing resistor, thus maintaining a constant 1A of charge current. The current limit loop is stabilized by compensating the LM301A with C1 (the standard frequency compensation used with this op-amp) and C2, which is additional compensation needed when D3 is forward biased. This helps speed up the response time during the reverse bias of D3. When the LM301A output is low, diode D3 reverse biases and prevents the op-amp from pulling more current through the emitter of Q2. This is important when the battery voltage reaches 8.4V, and the 1A charge current is no longer needed. Resistor R5 isolates the LM301A feedback node at the emitter of Q2. The battery voltage is sensed and buffered by the op-amp section of the LM10C, connected as a voltage follower driving the LM3420. When the battery voltage reaches 8.4V, the LM3420 will begin regulating by sourcing current into R8, which controls the collector current of Q2, which in turn reduces the gate voltage of Q3 and becomes a constant voltage regulator for charging the battery. Resistor R6 isolates the LM3420 from the common feedback node at the emitter of Q2. If R5 and R6 are omitted, oscillations could occur during the transition from the constant-current to the constant-voltage mode. D2 and the PNP transistor input DS012359-12 FIGURE 7. High Efficiency Switching Regulator Constant Current/Constant Voltage 2-Cell Charger DS012359-13 FIGURE 8. Low Dropout Constant Current/Constant Voltage Li-Ion Battery Charger A switching regulator, constant-current, constant-voltage two-cell Li-Ion battery charging circuit is shown in Figure 7. This circuit provides much better efficiency, especially over a wide input voltage range than the linear topologies. For a 1A charger an LM2575-ADJ. switching regulator IC is used in a standard buck topology. For other currents, or other packages, other members of the SIMPLE SWITCHERTM buck regulator family may be used. Circuit operation is as follows. With a discharged battery connected to the charger, the circuit operates as a constant current source. The constant-current portion of the charger is formed by the loop consisting of one half of the LM358 op amp along with gain setting resistors R3 and R4, current sensing resistor R5, and the feedback reference voltage of 1.23V. Initially the LM358's output is low causing the output of the LM2575-ADJ. to rise thus causing some charging current to flow into the battery. When the current reaches 1A, it is sensed by resistor R5 (50 m), and produces 50 mV. This 50 mV is amplified by the op-amps gain of 25 to produce 13 www.national.com LM3420-4.2/LM3420-8.2/LM3420-8.4/LM3420-12.6/LM3420-16.8 Application Circuits LM3420-4.2/LM3420-8.2/LM3420-8.4/LM3420-12.6/LM3420-16.8 Application Circuits The circuit in Figure 8 is very similar to Figure 7, except the switching regulator has been replaced with a low dropout linear regulator, allowing the input voltage to be as low as 10V. The constant current and constant voltage control loops are the same as the previous circuit. Diode D2 has been changed to a Schottky diode to provide a reduction in the overall dropout voltage of this circuit, but Schottky diodes typically have higher leakage currents than a standard silicon diode. This leakage current could discharge the battery if the input voltage is removed for an extended period of time. Another variation of a constant current/constant voltage switch mode charger is shown in Figure 9. The basic feedback loops for current and voltage are similar to the previous circuits. This circuit has the current sensing resistor, for the constant current part of the feedback loop, on the positive side of the battery, thus allowing a common ground between the input supply and the battery. Also, the LMC7101 op-amp is available in a very small SOT23-5 package thus allowing a very compact pc board design. Diode D4 prevents the battery from discharging through the charger circuitry if the input voltage is removed, although the quiescent current of the LM3420 will still be present (approximately 85 A). (Continued) 1.23V, which is applied to the feedback pin of the LM2575-ADJ. to satisfy the feedback loop. Once the battery voltage reaches 8.4V, the LM3420 takes over and begins to control the feedback pin of the LM2575-ADJ. The LM3420 now regulates the voltage across the battery, and the charger becomes a constant-voltage charger. Loop compensation network R6 and C3 ensure stable operation of the charger circuit under both constant-current and constant-voltage conditions. If the input supply voltage is removed, diode D2 and the PNP input stage of the LM358 become reversed biased and disconnects the battery to ensure that the battery is not discharged. Diode D3 reverse biases to prevent the op-amp from sinking current when the charger changes to constant voltage mode. The minimum supply voltage for this charger is approximately 11V, and the maximum is around 30V (limited by the 32V maximum operating voltage of the LM358). If another op-amp is substituted for the LM358, make sure that the input common-mode range of the op-amp extends down to ground so that it can accurately sense 50 mV. R1 is included to provide a minimum load for the switching regulator to assure that switch leakage current will not cause the output to rise when the battery is removed. DS012359-14 FIGURE 9. High Efficiency Switching Charger with High Side Current Sensing www.national.com 14 (Continued) DS012359-15 FIGURE 10. (Fast) Pulsed Constant Current 2-Cell Charger 15 www.national.com LM3420-4.2/LM3420-8.2/LM3420-8.4/LM3420-12.6/LM3420-16.8 Application Circuits LM3420-4.2/LM3420-8.2/LM3420-8.4/LM3420-12.6/LM3420-16.8 Application Circuits off time will be very short (1 ms or less), but when the battery approaches full charge, the off time will begin increasing to tens of seconds, then minutes, and eventually hours. (Continued) A rapid charge Lithium-Ion battery charging circuit is shown in Figure 10. This configuration uses a switching regulator to deliver the charging current in a series of constant current pulses. At the beginning of the charge cycle (constant-current mode), this circuit performs identically to the previous LM2575 charger by charging the battery at a constant current of 1A. As the battery voltage reaches 8.4V, this charger changes from a constant continuous current of 1A to a 5 second pulsed 1A. This allows the total battery charge time to be reduced considerably. This is different from the other charging circuits that switch from a constant current charge to a constant voltage charge once the battery voltage reaches 8.4V. After charging the battery with 1A for 5 seconds, the charge stops, and the battery voltage begins to drop. When it drops below 8.4V, the LM555 timer again starts the timing cycle and charges the battery with 1A for another 5 seconds. This cycling continues with a constant 5 second charge time, and a variable off time. In this manner, the battery will be charged with 1A for 5 seconds, followed by an off period (determined by the battery's state of charge), setting up a periodic 1A charge current. The off time is determined by how long it takes the battery voltage to decrease back down to 8.4V. When the battery first reaches 8.4V, the The constant-current loop for this charger and the method used for programming the 1A constant current is identical to the previous LM2575-ADJ. charger. In this circuit, a second LM3420-8.4 has its VREG increased by approximately 400 mV (via R2), and is used to limit the output voltage of the charger to 8.8V in the event of a bad battery connection, or the battery is removed or possibly damaged. The LM555 timer is connected as a one-shot, and is used to provide the 5 second charging pulses. As long as the battery voltage is less than the 8.4V, the output of IC3 will be held low, and the LM555 one-shot will never fire (the output of the LM555 will be held high) and the one-shot will have no effect on the charger. Once the battery voltage exceeds the 8.4V regulation voltage of IC3, the trigger pin of the LM555 is pulled high, enabling the one shot to begin timing. The charge current will now be pulsed into the battery at a 5 second rate, with the off time determined by the battery's state of charge. The LM555 output will go high for 5 seconds (pulling down the collector of Q1) which allows the 1A constant-current loop to control the circuit. DS012359-16 FIGURE 11. MOSFET Low Dropout Charger Figure 11 shows a low dropout constant voltage charger using a MOSFET as the pass element, but this circuit does not include current limiting. This circuit uses Q3 and a Schottky diode to isolate the battery from the charging circuitry when the input voltage is removed, to prevent the battery from discharging. Q2 should be a high current (0.2) FET, while Q3 can be a low current (2) device. Note: Although the application circuits shown here have been built and tested, they should be thoroughly evaluated with the same type of battery the charger will eventually be used with. www.national.com Different battery manufacturers may use a slightly different battery chemistry which may require different charging characteristics. Always consult the battery manufacturer for information on charging specifications and battery details, and always observe the manufacturers precautions when using their batteries. Avoid overcharging or shorting Lithium-Ion batteries. 16 LM3420-4.2, -8.2, -8.4, -12.6, -16.8 Lithium-Ion Battery Charge Controller Physical Dimensions inches (millimeters) unless otherwise noted 5-Lead Small Outline Package (M5) For Ordering Information See Figure 1 In This Data Sheet NS Package Number MF05A LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: ap.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. National P/N LM3420 - Lithium-Ion Battery Charge Controller See Wireless Products Products > Analog - Regulators > Lithium-Ion Battery Charge & Protection > LM3420 LM3420 Product Folder Lithium-Ion Battery Charge Controller Generic P/N 3420 General Description Features Package & Models Datasheet Parametric Table Samples & Pricing Parametric Table Multiple Output Capability No Full Charge Voltage, max (Volt) 12.60, 16.80, 8.20, 8.40 On/Off Pin No Programmable Voltage No Error Flag No Charge Voltage Control Yes Input Voltage, min (Volt) - Charge Current Control No Input Voltage, max (Volt) - Charge Time Control No Output Current, max Set by External FET Cell Fault Protection No Full Charge Voltage, min (Volt) 12.60, 16.80, 8.20, 8.40 Overvoltage Protection No Datasheet Size in Date Kbytes Title 28LM3420-4.2, -8.2, -8.4, -12.6, -16.8 Lithium-Ion Battery 384 JulCharge Controller Kbytes 00 LM3420-4.2, -8.2, -8.4, -12.6, -16.8 Lithium-Ion Battery Charge Controller (JAPANESE) 229 Kbytes View Online Download Receive via Email View Online Download Receive via Email View Online Download Receive via Email If you have trouble printing or viewing PDF file(s), see Printing Problems. Package Availability, Models, Samples & Pricing Part Number Package Type LM3420AM5-12.6 SOT-23 Status Pins MSL 5 MSL Full production Budgetary Samples & Pricing Electronic Orders SPICE IBIS Qty $US each Models N/A N/A Samples 1K+ $1.0500 Std Pack Size Package Marking reel of 1000 D04A Z1T file:///H|/imaging/BITTING/cpl/20020808_1/08062002_10/NATL/08062002_HTML/LM3420.html (1 of 4) [09-Aug-2002 12:24:26 PM] National P/N LM3420 - Lithium-Ion Battery Charge Controller 1K+ $1.0500 reel of 1000 D05A Z1T 1K+ $1.0500 reel of 1000 D02A Z1T 1K+ $1.0500 reel of 1000 D07A Z1T 1K+ $1.0500 reel of 1000 D03A Z1T 1K+ $0.9000 reel of 1000 D04B Z1T 1K+ $0.9000 reel of 1000 D05B Z1T 1K+ $0.9000 reel of 1000 D02B Z1T 1K+ $0.9000 reel of 1000 D07B Z1T 1K+ $0.9000 reel of 1000 D03B Z1T Samples LM3420AM5-16.8 SOT-23 LM3420AM5-4.2 SOT-23 5 MSL Full production N/A N/A 5 MSL Full production N/A N/A Buy Now Samples Buy Now Samples LM3420AM5-8.2 SOT-23 LM3420AM5-8.4 SOT-23 5 MSL Full production N/A N/A 5 MSL Full production N/A N/A Buy Now Samples Buy Now LM3420M5-12.6 SOT-23 5 MSL Full production Samples N/A N/A Buy Now Samples LM3420M5-16.8 SOT-23 LM3420M5-4.2 SOT-23 LM3420M5-8.2 SOT-23 LM3420M5-8.4 SOT-23 5 MSL Full production N/A N/A 5 MSL Full production N/A N/A 5 MSL Full production N/A N/A 5 MSL Full production N/A N/A Buy Now Samples Buy Now Samples Buy Now Samples Buy Now LM3420AM5X-12.6 SOT-23 5 MSL Full production N/A N/A 1K+ $1.0500 reel of 3000 D04A Z1T LM3420AM5X-16.8 SOT-23 5 MSL Full production N/A N/A 1K+ $1.0500 reel of 3000 D05A Z1T LM3420AM5X-4.2 SOT-23 5 MSL Full production N/A N/A 1K+ $1.0500 reel of 3000 D02A Z1T LM3420AM5X-8.2 SOT-23 5 MSL Full production N/A N/A 1K+ $1.0500 reel of 3000 D07A Z1T LM3420AM5X-8.4 SOT-23 5 MSL Full production N/A N/A 1K+ $1.0500 reel of 3000 D03A Z1T LM3420M5X-12.6 SOT-23 5 MSL Full production N/A N/A 1K+ $0.9000 reel of 3000 D04B Z1T LM3420M5X-16.8 SOT-23 5 MSL Full production N/A N/A 1K+ $0.9000 reel of 3000 D05B Z1T Buy Now Buy Now Buy Now file:///H|/imaging/BITTING/cpl/20020808_1/08062002_10/NATL/08062002_HTML/LM3420.html (2 of 4) [09-Aug-2002 12:24:26 PM] National P/N LM3420 - Lithium-Ion Battery Charge Controller 1K+ $0.9000 reel of 3000 D02B Z1T N/A 1K+ $0.9000 reel of 3000 D07B Z1T N/A N/A 1K+ $0.9000 reel of 3000 D03B Z1T Full production N/A N/A Samples tray of N/A - Die Full production N/A N/A Samples tray of N/A - LM3420A-8.4 MDA Die Full production N/A N/A Samples tray of N/A - LM3420A12.6 MDA Die Full production N/A N/A Samples tray of N/A - LM3420A16.8 MDA Die Full production N/A N/A Samples tray of N/A - LM3420A-4.2 MWA Wafer Full production N/A N/A wafer jar of N/A - LM3420A-8.2 MWA Wafer Full production N/A N/A wafer jar of N/A - LM3420A-8.4 MWA Wafer Full production N/A N/A wafer jar of N/A - LM3420A12.6 MWA Wafer Full production N/A N/A wafer jar of N/A - LM3420A16.8 MWA Wafer Full production N/A N/A wafer jar of N/A - LM3420M5X-4.2 SOT-23 5 MSL Full production N/A N/A LM3420M5X-8.2 SOT-23 5 MSL Full production N/A LM3420M5X-8.4 SOT-23 5 MSL Full production LM3420A-4.2 MDA Die LM3420A-8.2 MDA Buy Now Buy Now General Description The LM3420 series of controllers are monolithic integrated circuits designed for charging and end-of-charge control for Lithium-Ion rechargeable batteries. The LM3420 is available in five fixed voltage versions for one through four cell charger applications (4.2V, 8.2V/8.4V, 12.6V and 16.8V respectively). Included in a very small package is an (internally compensated) op amp, a bandgap reference, an NPN output transistor, and voltage setting resistors. The amplifier's inverting input is externally accessible for loop frequency compensation. The output is an open-emitter NPN transistor capable of driving up to 15 mA of output current into external circuitry. A trimmed precision bandgap reference utilizes temperature drift curvature correction for excellent voltage stability over the operating temperature range. Available with an initial tolerance of 0.5% for the A grade version, and 1% for the standard version, the LM3420 allows for precision end-of-charge control for LithiumIon rechargeable batteries. file:///H|/imaging/BITTING/cpl/20020808_1/08062002_10/NATL/08062002_HTML/LM3420.html (3 of 4) [09-Aug-2002 12:24:26 PM] National P/N LM3420 - Lithium-Ion Battery Charge Controller The LM3420 is available in a sub-miniature 5-lead SOT23-5 surface mount package thus allowing very compact designs. Features Voltage options for charging 1, 2, 3 or 4 cells Tiny SOT23-5 package Precision (0.5%) end-of-charge control Drive capability for external power stage Low quiescent current, 85 A (typ.) Applications Lithium-Ion battery charging Suitable for linear and switching regulator charger designs [Information as of 5-Aug-2002] Search Design Purchasing Quality Company Home About Languages . Website Guide . About "Cookies" . National is QS 9000 Certified . Privacy/Security Statement . Contact Us . Site Terms & Conditions of Use . Copyright 2002 (c) National Semiconductor Corporation . My Preferences . Feedback file:///H|/imaging/BITTING/cpl/20020808_1/08062002_10/NATL/08062002_HTML/LM3420.html (4 of 4) [09-Aug-2002 12:24:26 PM]