CUSTOMER DRAWING
.
Raychem
Devices
TITLE:
SOLDERSLEEVE DEVICE WITH
PRE-INSTALLED LEAD, IMMERSION RESISTANT
Unless otherwise specified dimensions are in millimeters.
[Inches dimensions are shown in brackets]
DOCUMENT NO.:
SO63-X-9036-GA
TOLERANCES:
0.00 N/A
0.0 N/A
0 N/A
ANGLES: N/A
Tyco Electronics reserves the right to amend
this drawing at any time. Users should evaluate
the suitability of the product for their
application.
REV.:
B
DATE:
17-Feb-2017
PREPARED BY:
mforonda
ECO NUMBER:
ECO-17-002137
REPLACES:
D060206
CAGE CODE :
06090
SCALE:
---
SIZE:
A
SHEET:
1 of 1
© 2005-2017 TE Connectivity Corporation. All rights reserved. SolderSleeve is a trademark of Tyco Electronics Corporation
If this document is printed it becomes uncontrolled. Check for the latest revision.
Product
Name
Mark
Product Dimensions
A±1.75
[A±0.070]
øB
min
øC
min
SO63-1-9036-22
SO631R
16.50
[0.650]
1.90
[0.075]
2.65
[0.105]
SO63-1-9036-20
SO63-1-9036-18
SO63-2-9036-22
SO632R
16.50
[0.650]
2.65
[0.105]
3.55
[0.145]
SO63-2-9036-20
SO63-2-9036-18
SO63-3-9036-22
SO633R
16.50
[0.650]
4.30
[0.170]
5.00
[0.200]
SO63-3-9036-20
SO63-3-9036-18
SO63-4-9036-22
SO634R
19.10
[0.750]
5.95
[0.235]
6.50
[0.255]
SO63-4-9036-20
SO63-4-9036-18
SO63-5-9036-22
SO635R
19.10
[0.750]
7.00
[0.275]
7.60
[0.300]
SO63-5-9036-20
SO63-5-9036-18
MATERIALS
1. INSULATION SLEEVE: Heat-shrinkable, transparent blue, radiation cross-linked modified polyvinylidene fluoride. Marked
per table.
2. SOLDER PREFORM WITH FLUX AND THERMAL INDICATOR RING:
SOLDER: TYPE Sn63 per ANSI / J-STD-006.
FLUX: TYPE ROL1 per ANSI / J STD-004.
TERMAL INDICATOR RING: Fusible alloy with melt point of 221°C.
3. MELTABLE RINGS: Environment resistant fluorocarbon-based thermoplastic
4. PRE-INSTALLED LEAD: Raychem 55PC6121-GA. “GA”=size (AWG) of lead, color: white with 2 black stripes.
APPLICATION
1. These parts are designed to provide an environment resistant shield termination on cables, rated for 125C min. having tin or
silver-plated shields, and jackets compatible with the insert material. See M83519/2 or consult TE Connectivity.
2. When properly installed, these parts will meet the performance requirements of Raychem RT-1404 and SAE-AS-83519/2.
3. Part selection: Measure cable jacket diameter at its maximum point. Select the smallest terminator that has a “B” diameter
larger than the cable diameter.
4. Cable is to be stripped to expose 6.0 -7.5mm [0.235-0.295] of shield.
5. Part may be installed using any Raychem approved convection or infra-red heating tool. Tools must be equipped with a
suitable reflector. For detailed assembly instruction see Raychem RCPS-100-70.