WL50S High-Intensity Work Spot Light Datasheet General-purpose LED work lighting For the latest technical information about this product, including specifications, dimensions, and wiring, see www.bannerengineering.com. * * * * * * Three lens options, depending on model, to vary spot size Illuminates a large area with an even pattern of light and no shadows 12 to 30V dc operation Cabled and quick-disconnect models available 50 mm diameter with flat profile and 30 mm mounting base Rugged sealed housing rated to IP69K WARNING: Not To Be Used for Personnel Protection Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Models Model1 LED Color Lumens Lux Lens Angle 0.5 m 1m WL50SWL5Q White, 5000-8300 K 295 13780 3445 WL50SRL5Q Red, 620-630 nm 110 8000 2000 WL50SGL5Q Green, 520-535 nm 210 13000 3250 WL50SWL11Q White, 5000-8300 K 285 5460 1365 WL50SRL11Q Red, 620-630 nm 105 2500 625 WL50SGL11Q Green, 520-535 nm 200 3900 975 WL50SWL20Q White, 5000-8300 K 270 2000 500 WL50SRL20Q Red, 620-630 nm 100 1040 260 WL50SGL20Q Green, 520-535 nm 190 1700 425 Connection 5 (smaller, more focused spot; see graph) 11 (larger spot; see graph) 5 pin Euro integral QD connector (use with a 4-wire mating cordset; only 2 wires used for connection) 20 (largest spot; see graph) 1 Integral QD models only are listed. For integral 2 m (6.5') PVC cable, omit suffix Q from model number (example, WL50SWL5). A model with a QD requires a mating cordset (see 4-Pin Euro-Style Cordsets on page 3). P/N 158250 Rev. D 14 November 2013 0 158250 3 WL50S High-Intensity Work Spot Light Specifications Supply Voltage and Current Operating voltage: 12 to 30V dc Current draw: 400 mA max. Environmental Rating IEC IP67, IP69K per DIN 40050-9 NOTE: Do not spray the cable with a high-pressure sprayer or cable damage will result. Supply Protection Circuitry Protected against reverse polarity and transient voltages Light Source Three high-intensity LEDs; see models table for color temperature or wavelengths Operating Conditions -20 C to +50 C (-4 F to +122 F) 95% maximum relative humidity (non-condensing) Useful Life When operating within specifications, output will decrease less than 30% after 50,000 hours. Vibration and Mechanical Shock All models meet Mil. Std. 202F requirements method 201A (vibration: 10 to 60 Hz max., double amplitude 0.06", maximum acceleration 10G). Also meets IEC 947-5-2; 30G 11 ms duration, half sine wave. Construction Black anodized aluminum housing; polycarbonate window; nickel-plated QD connector or PVC-jacketed cable; black zinc-plated steel mounting nut Storage Temperature -40 C to +70 C (-40 F to +158 F) Certifications Mounting: 30x1.5 mm thread base mount Connections Integral 5-pin M12/Euro style QD or 2 m (6.5 ft) integral cable, depending on model; 4-pin connecting cordset required for QD models; only 2 wires used Beam Patterns 2 www.bannerengineering.com - tel: 763-544-3164 P/N 158250 Rev. D WL50S High-Intensity Work Spot Light Dimensions Wiring Female Wiring Key: 1 = Brown 3 = Blue 1 1 3 1 = Brown 3 = BlueMale 12 - 30V dc 3 1 3 4-Pin Euro-Style Cordsets 4-Pin Threaded M12/Euro-Style Cordsets Model Length MQDC-406 1.83 m (6 ft) MQDC-415 4.57 m (15 ft) MQDC-430 9.14 m (30 ft) MQDC-450 15.2 m (50 ft) Style Dimensions Pinout 44 Typ. Straight M12 x 1 o 14.5 www.bannerengineering.com - tel: 763-544-3164 3 4 1 2 3 4 P/N 158250 Rev. D 2 1 = = = = Brown White Blue Black 3 WL50S High-Intensity Work Spot Light 4-Pin Threaded M12/Euro-Style Cordsets Model Length Style MQDC-406RA 1.83 m (6 ft) MQDC-415RA 4.57 m (15 ft) MQDC-430RA 9.14 m (30 ft) MQDC-450RA 15.2 m (50 ft) Dimensions Pinout 32 Typ. [1.26"] 30 Typ. [1.18"] Right-Angle M12 x 1 o 14.5 [0.57"] Mounting Brackets All measurements are in mm SMB30A * Right-angle bracket with curved slot for versatile orientation * Clearance for M6 (1/4 in) hardware * Mounting hole for 30 mm sensor * 12-ga. stainless steel 45 C 61 B A 69 67 B 58 29 A Hole center spacing: A=o 50.8 Hole size: A=o 7.0, B=o 30.0 Hole center spacing: A to B=40 Hole size: A=o 6.3, B= 27.1 x 6.3, C=o 30.5 SMB30FA * Swivel bracket with tilt and pan movement for precise adjustment * Mounting hole for 30 mm sensor * 12-ga. 304 stainless steel * Easy sensor mounting to extrude rail T-slot * Metric and inch size bolt available SMB30SC * Swivel bracket with 30 mm mounting hole for sensor * Black reinforced thermoplastic polyester * Stainless steel mounting and swivel locking hardware included 83.2 36.3 68.9 B A SMBAMS30RA * Right-angle SMBAMS series bracket * 30 mm hole for mounting sensors * Articulation slots for 90+ rotation * 12-ga. (2.6 mm) cold-rolled steel 45 C 53 A B 48 Hole center spacing: A=26.0, A to B=13.0 Hole size: A=26.8 x 7.0, B=o 6.5, C=o 31.0 Bolt thread: SMB30FA, A= 3/8 - 16 x 2 in; SMB30FAM10, A= M10 1.5 x 50 Hole size: B= o 30.1 SMB30MM * 12-ga. stainless steel bracket with curved mounting slots for versatile orientation * Clearance for M6 (1/4 in) hardware * Mounting hole for 30 mm sensor C 57 Hole center spacing: A = 51, A to B = 25.4 Hole size: A = 42.6 x 7, B = o 6.4, C = o 30.1 4 57 70 B A SMBAMS30P * Flat SMBAMS series bracket * 30 mm hole for mounting sensors * Articulation slots for 90+ rotation * 12-ga. 300 series stainless steel 45 C 93 A B Hole center spacing: A=26.0, A to B=13.0 Hole size: A=26.8 x 7.0, B=o 6.5, C=o 31.0 www.bannerengineering.com - tel: 763-544-3164 P/N 158250 Rev. D WL50S High-Intensity Work Spot Light Banner Engineering Corp Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product. THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. www.bannerengineering.com - tel: 763-544-3164