Datasheet
General-purpose LED work lighting
For the latest technical information about this product, including specifications, dimensions, and wiring, see
www.bannerengineering.com.
• Three lens options, depending on model, to vary spot size
• Illuminates a large area with an even pattern of light and no shadows
• 12 to 30V dc operation
• Cabled and quick-disconnect models available
• 50 mm diameter with flat profile and 30 mm mounting base
• Rugged sealed housing rated to IP69K
WARNING: Not To Be Used for Personnel Protection
Never use this device as a sensing device for personnel protection. Doing so could lead to
serious injury or death. This device does not include the self-checking redundant circuitry necessary
to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an
energized or de-energized sensor output condition.
Models
Model1LED Color Lumens Lux Lens Angle Connection
0.5 m 1 m
WL50SWL5Q White, 5000-8300 K 295 13780 3445 ±5° (smaller,
more focused
spot; see graph)
5 pin Euro integral
QD connector (use
with a 4-wire
mating cordset;
only 2 wires used
for connection)
WL50SRL5Q Red, 620-630 nm 110 8000 2000
WL50SGL5Q Green, 520-535 nm 210 13000 3250
WL50SWL11Q White, 5000-8300 K 285 5460 1365 ±11° (larger
spot; see graph)
WL50SRL11Q Red, 620-630 nm 105 2500 625
WL50SGL11Q Green, 520-535 nm 200 3900 975
WL50SWL20Q White, 5000-8300 K 270 2000 500 ±20° (largest
spot; see graph)
WL50SRL20Q Red, 620-630 nm 100 1040 260
WL50SGL20Q Green, 520-535 nm 190 1700 425
1Integral QD models only are listed. For integral 2 m (6.5') PVC cable, omit suffix Q from model number (example, WL50SWL5). A model with a QD
requires a mating cordset (see 4-Pin Euro-Style Cordsets on page 3).
WL50S High-Intensity Work Spot Light
P/N 158250 Rev. D 14 November 2013
0 158250 3
Specifications
Supply Voltage and Current
Operating voltage: 12 to 30V dc
Current draw: 400 mA max.
Supply Protection Circuitry
Protected against reverse polarity and transient
voltages
Light Source
Three high-intensity LEDs; see models table for color
temperature or wavelengths
Useful Life
When operating within specifications, output will
decrease less than 30% after 50,000 hours.
Construction
Black anodized aluminum housing; polycarbonate
window; nickel-plated QD connector or PVC-jacketed
cable; black zinc-plated steel mounting nut
Mounting:
30x1.5 mm thread base mount
Connections
Integral 5-pin M12/Euro style QD or 2 m (6.5 ft)
integral cable, depending on model; 4-pin connecting
cordset required for QD models; only 2 wires used
Environmental Rating
IEC IP67, IP69K per DIN 40050-9
NOTE: Do not spray the cable with a
high-pressure sprayer or cable damage
will result.
Operating Conditions
−20 °C to +50 °C (−4 °F to +122 °F)
95% maximum relative humidity (non-condensing)
Vibration and Mechanical Shock
All models meet Mil. Std. 202F requirements method
201A (vibration: 10 to 60 Hz max., double amplitude
0.06", maximum acceleration 10G). Also meets IEC
947-5-2; 30G 11 ms duration, half sine wave.
Storage Temperature
−40 °C to +70 °C (−40 °F to +158 °F)
Certifications
Beam Patterns
WL50S High-Intensity Work Spot Light
2 www.bannerengineering.com - tel: 763-544-3164 P/N 158250 Rev. D
Dimensions
Wiring
1
3
12 - 30V dc 1 = Brown
3 = Blue
1
3
1
3
Male
Female
Wiring Key:
1 = Brown
3 = Blue
4-Pin Euro-Style Cordsets
4-Pin Threaded M12/Euro-Style Cordsets
Model Length Style Dimensions Pinout
MQDC-406 1.83 m (6 ft)
Straight
44 Typ.
ø 14.5
M12 x 1
2
3
4
1
1 = Brown
2 = White
3 = Blue
4 = Black
MQDC-415 4.57 m (15 ft)
MQDC-430 9.14 m (30 ft)
MQDC-450 15.2 m (50 ft)
WL50S High-Intensity Work Spot Light
P/N 158250 Rev. D www.bannerengineering.com - tel: 763-544-3164 3
4-Pin Threaded M12/Euro-Style Cordsets
Model Length Style Dimensions Pinout
MQDC-406RA 1.83 m (6 ft)
Right-Angle
32 Typ.
[1.26"]
30 Typ.
[1.18"]
ø 14.5 [0.57"]
M12 x 1
MQDC-415RA 4.57 m (15 ft)
MQDC-430RA 9.14 m (30 ft)
MQDC-450RA 15.2 m (50 ft)
Mounting Brackets
All measurements are in mm
SMB30A
• Right-angle bracket with
curved slot for versatile
orientation
• Clearance for M6 (¼ in)
hardware
• Mounting hole for 30 mm
sensor
• 12-ga. stainless steel
45
61
69
A
B
C
Hole center spacing: A to B=40
Hole size: A=ø 6.3, B= 27.1 x 6.3, C=ø 30.5
SMB30SC
• Swivel bracket with 30 mm
mounting hole for sensor
• Black reinforced
thermoplastic polyester
• Stainless steel mounting and
swivel locking hardware
included
67
58
29
B
A
Hole center spacing: A=ø 50.8
Hole size: A=ø 7.0, B=ø 30.0
SMB30FA
• Swivel bracket with tilt and
pan movement for precise
adjustment
• Mounting hole for 30 mm
sensor
• 12-ga. 304 stainless steel
• Easy sensor mounting to
extrude rail T-slot
• Metric and inch size bolt
available
A
B68.9
36.3
83.2
Bolt thread: SMB30FA, A= 3/8 - 16 x 2 in; SMB30FAM10, A= M10 -
1.5 x 50
Hole size: B= ø 30.1
SMBAMS30RA
• Right-angle SMBAMS series
bracket
• 30 mm hole for mounting
sensors
• Articulation slots for 90°+
rotation
• 12-ga. (2.6 mm) cold-rolled
steel
53
48
45
A
C
B
Hole center spacing: A=26.0, A to B=13.0
Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0
SMB30MM
• 12-ga. stainless steel bracket
with curved mounting slots
for versatile orientation
• Clearance for M6 (¼ in)
hardware
• Mounting hole for 30 mm
sensor
70
57
A
B
C
57
Hole center spacing: A = 51, A to B = 25.4
Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 30.1
SMBAMS30P
• Flat SMBAMS series bracket
• 30 mm hole for mounting
sensors
• Articulation slots for 90°+
rotation
• 12-ga. 300 series stainless
steel
45
93 A
C
B
Hole center spacing: A=26.0, A to B=13.0
Hole size: A=26.8 x 7.0, B=ø 6.5, C=ø 31.0
WL50S High-Intensity Work Spot Light
4 www.bannerengineering.com - tel: 763-544-3164 P/N 158250 Rev. D
Banner Engineering Corp Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following
the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture
which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty
does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR
IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR
TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO
EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR
ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR
SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE
PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY,
NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any
obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp.
WL50S High-Intensity Work Spot Light
www.bannerengineering.com - tel: 763-544-3164
