SPED2 4.5mm-travel Push-push Type Smooth and linear operation feeling Detector Typical Specifications Items Specifications Slide RatingResistive load 1A 14.5V DC Contact resistance Initial / After operating life 100m max. / 100m max. Operating force 4.170.74N Push Operating lifeWith load 30,000 cycles1A 14.5V DC 2-pole, 1-position 1-pole, 2-position Circuit configuration Rotary Product Line Power Changeover timing Total travel mm Non shorting 4.5 Mounting method Poles PC board 2 1 Connector 1 2 Positions Operation Alternate Terminal type Minimum order unitpcs. Product No. Drawing No. 1,120 SPED220200 1 2,000 SPED210203 2 Japan Export For PC board 280 - 400 Dual-in-line Package Type Packing Specifications Tray Number of packagespcs. Product No. 1 case / Japan 1 case / export packing Export package measurements mm 280 1,120 555x375x223 SPED220200 Horizontal Type Bulk Number of packagespcs. Product No. Vertical Type 1 case / Japan 1 case / export packing Export package measurements mm 400 2,000 400x270x290 SPED210203 Dimensions Unit:mm No. PC board mounting dimensions Viewed from the mounting face side Style 16.8 14 1.05 15 2-2.1 Turnover position A Travel o9.7 o4.8 15.58 2 11.65 ho le 43.55 2.85 9.5 8.3 o3 05 3.5 4.5 0.8 18.3 26.7 1 o10 o3 . 11.65 2.2 o11.15 2.65 4-1 2.65 Terminal No. 2 Terminal No. C1 8 o1 . 2 ho le 8 (T=1.6) Terminal No. C2 Terminal No. 1 136 Refer to P.140 for soldering conditions. SPED24.5mm-travel Push-push Type Unit:mm No. Detector Dimensions Style Slide 16.8 14 6.1 Push Turnover position o11.15 2 Travel 3.5 4.5 6.75 8.8 o10 1.2 9.5 o10 o4.8 Terminal No.1 Rotary 17.2 o9.7 Terminal No. 2 8 Terminal No. C1 C2 Power C2 1 2 Vertical Type Note Factory setting for contact points can be either 1 or 2. Horizontal Type C1 Dual-in-line Package Type Circuit Diagram 137 SPEF SPED2 SPED3 SPED4 SPED5 Detector Vertical Series Photo 9.4 D 9 16.8 H 6.9 18.3 16.97 13.1 18 Travelmm 1.5 -- -- -- -- Total travelmm 2.7 4.5 3.8 Number of poles 1 1 2 1 Dimensions mm 18 -40 to 95 Ratingmax. Resistive load 1A 14.5V DC Ratingmin. Resistive load Durability -- -- 2A 14.5V DC -- -- -- -- -- -- -- -- Operating life with load at max. rated load 30,000 cycles 100m max. Initial contact resistance 100m max. 3M min. 100V DC Voltage proof Terminal strength Mechanical Operating performance Actuator direction strength Pulling direction 3M min. 500V DC 100V AC for 1minute -- -- -- 90N 30N -- Cold Environmental performance Dry heat -- -- Wire strength 30N 98N 90N 98N -- -- -- -40 96h 85 96h Damp heat Page Vertical Type Insulation resistance Horizontal Type Electrical performance Operating life without load 50A 3V DC Dual-in-line Package Type Life cycle Power -40 to 85 18.2 Rotary Automotive use 13.5 Push Operating temperature range 14 Slide W 85 96h (Connector type) 105 192h (Dip type) 105 192h 40, 90 to 95%RH 96h 134 136 138 Push Switches Soldering Conditions 140 Push Switches Cautions 141 Note Indicates applicability to all products in the series. 117 Push Switches Soldering Conditions Detector Example of Reflow Soldering Condition 1. Heating method: Double heating method with infrared heater. 2. Temperature measurement: Thermocouple 0.1 to 0.2 CA (K) or CC (T) at soldering portion (copper foil surface). A heat resisting tape should be used for fixed measurement. 3. Temperature profile Push Temperature (C ) Slide 300 A max. B 200 D E 100 Rotary Room temperature Time (s) Pre-heating F max. C Power Dual-in-line Package Type SeriesReflow type A 3s max. B Cs D E Fs 260 230 40 180 150 120 SPEG SPEJ SPEF SPEH Horizontal Type Notes 1. The condition mentioned above is the temperature on the mounting surface of a PC board. There are cases where the PC board's temperature greatly differs from that of the switch, depending on the PC board's material, size, thickness, etc. The above-stated conditions shall also apply to switch surface temperatures. 2. Soldering conditions differ depending on reflow soldering machines. Prior verification of soldering condition is highly recommended. Vertical Type Reference for Hand Soldering Series Soldering temperature Soldering time SPPJ3, SPPJ2, SPUN, SPPH4, SPPH1 35010 3+1/0s SPED2, SPED4 35010 30.5s SPEJ 35010 4s max. SPEG, SPEF 3505 3s max. SPEH, SPPH2 350 max. 3s max. SPUJ 30010 3+1/0s Reference for Dip Soldering (For PC board terminal types) Series 140 For PC board Items Dip soldering Preheating temperature Preheating time Soldering temperature Duration of immersion SPPJ3 100 max. 60s max. 2605 51s SPUN 100 max. 60s max. 2605 101s SPUJ, SPPH2, SPPH4 -- 2605 51s SPPJ2, SPPH1, SPED2, SPED4, SPEF -- 2605 101s