Freescale Semiconductor Technical Data Document Number: MC13892 Rev. 19.0, 4/2014 Power Management Integrated Circuit (PMIC) for i.MX35/51 13892 The MC13892 is a Power Management Integrated Circuit (PMIC) designed specifically for use with the Freescale i.MX35 and i.MX51 families. It is also compatible with the i.MX27, i.MX31, and i.MX37 application processors targeting netbooks, ebooks, smart mobile devices, smart phones, personal media players, and portable navigation devices. This device is powered by SMARTMOS technology. POWER MANAGEMENT Features * Battery charger system for wall charging and USB charging * 10-bit ADC for monitoring battery and other inputs, plus a coulomb counter support module * Four adjustable output buck regulators for direct supply of the processor core and memory * 12 adjustable output LDOs with internal and external pass devices * Boost regulator for supplying RGB LEDs * Serial backlight drivers for displays and keypad, plus RGB LED drivers * Power control logic with processor interface and event detection * Real time clock and crystal oscillator circuitry, with coin cell backup and support for external secure real time clock on a companion system processor IC * Touch screen interface * SPI/I2C bus interface for control and register access VK SUFFIX 98ASA10820D 139-PIN 7X7MM BGA ORDERING INFORMATION See Device Variation Table on Page 2. Camera MMC NVR SSI IRDA TV Out DRAM BT (+FM) Line In/Out Camera Stereo Loudspeakers i.MX51 Apps Processor Audio IC Aud AP Mic Inputs Display Backlight USB Stereo headphones SPI/I2C Charger LED UI Power Power UI Backlight Adapter MC13892 MC13892 Power Management Power Mgmt & Integrated User Interface AP Circuit Li Ion Battery Aud& Pwr Mgmt RGB Color Indicators Touch Screen Coin Cell Battery Light Sensor Thermistor CALENDAR RTC Figure 1. MC13892 Typical Operating Circuit (c) Freescale Semiconductor, Inc., 2010 - 2014. All rights reserved. VL SUFFIX 98ASA10849D 186-PIN 12X12MM BGA DEVICE VARIATIONS DEVICE VARIATIONS Table 1. MC13892 Device Variations Part Number(1) Notes MC13892CJVK (2) MC13892AJVK (3) MC13892DJVK (2) (4) MC13892BJVK (3) MC13892VK (3) MC13892JVK (3) MC13892CJVL (2) MC13892AJVL (3) MC13892DJVL (2) (4) MC13892BJVL (3) MC13892VL (3) MC13892JVL (3) Notes 1. 2. 3. 4. Package Temperature Range (TA) Pin Map Description Global Reset Function Default ON 139-PIN 7x7 mm BGA Figure 3 Global Reset Function Default OFF No Global Reset Function -40 to +85 C Global Reset Function Default ON 186-PIN 12x12 mm BGA Figure 4 Global Reset Function Default OFF No Global Reset Function For Tape and Reel product, add an "R2" suffix to the part number. Recommended for all new designs Not recommended for new designs Backward compatible replacement part for MC13892VK, MC13892JVK, MC13892VL, MC13892JVL, MC13892BJVK, and MC13892BJVL MC13892 2 Analog Integrated Circuit Device Data Freescale Semiconductor INTERNAL BLOCK DIAGRAM Charger Interface and Control: 4 bit DAC, Clamp, Protection, Trickle Generation Battery Interface & Protection GNDLED LEDR LEDG LEDB GNDBL LEDKP LEDAD LEDMD GNDCHRG CHRGSE1B CHRGLED CHRGRAW CHRGCTRL1 CHRGISNS CHRGCTRL2 BPSNS BP BATTFET BATT BATTISNS INTERNAL BLOCK DIAGRAM Tri-Color LED Drive Backlight LED Drive PWR Gate Drive & Chg Pump PWGTDRV1 PWGTDRV2 LICELL, UID, Die Temp, GPO4 GNDADC ADIN5 Voltage / Current Sensing & Translation SW1 1050 mA Buck ADIN6 ADIN7 TSX1 10 Bit GP ADC MUX SW2 800 mA Buck A/D Result TSX2 TSY1 TSY2 A/D Control Touch Screen Interface Trigger Handling TSREF Die Temp & Thermal Warning Detection ADTRIG SW3 800 mA Buck To Interrupt Section SW4 800 mA Buck BATTISNSCC BATT CFP Coulomb CCOUT Counter SPIVCC MC13892 IC Shift Register CS CLK SPI Interface + Muxed I2C Optional Interface MOSI MISO GNDSPI SPI SW2IN SW2OUT GNDSW2 SW2FB O/P Drive SW3IN SW3OUT GNDSW3 SW3FB O/P Drive SW4IN SW4OUT GNDSW4 SW4FB DVS1 DVS2 SPI Control VBUS/ID Detectors VUSB2 Pass FET VAUDIO Pass FET VIOHI Pass FET VPLL Pass FET VDIG Pass FET OTG 5V SPI VUSB Regulator To Trimmed Circuits Trim-In-Package Control Logic Pass FET Control Logic PLL VDIG VCAM VGEN1DRV VGEN1 VGEN2 VGEN2DRV VGEN2 VINGEN3DRV Pass FET VGEN3 LICELL Best of Supply VSRTC CLK32K RESETB STANDBYSEC RESETBMCU INT WDI PUMS1 PUMS2 MODE BP 32 KHz Buffers VSRTC Enables & Control Core Control Logic, Timers, & Interrupts GNDCTRL XTAL2 GNDRTC XTAL1 GNDSUB8 GNDSUB9 32 KHz Crystal Osc Interrupt Inputs CLK32KMCU SPI Result Registers STANDBY Li Cell Charger GNDSUB7 VINDIG VGEN1 VGEN3 RTC + Calibration 32 KHz Internal Osc PWRON1 PWRON2 PWRON3 LCELL GNDSUB4 GNDSUB5 GNDSUB6 VINPLL VPLL VSDDRV VSD Switchers Monitor Timer Switch GNDSUB1 GNDSUB2 GNDSUB3 VINIOHI VIOHI GNDREG1 GNDREG2 GPO Control GNDREG3 GPO1 GPO2 GPO3 GPO4 Startup Sequencer Decode Trim? PUMS BP VINAUDIO VAUDIO VSD VUSB LICELL VINUSB2 VUSB2 VINCAMDRV VCAM VINUSB VVIDEODRV VVIDEO VVIDEO MC13892 Connector Interface UID Bi-directional Pin SWBSTIN SWBSTOUT SWBSTFB GNDSWBST Shift Register Reference Generation UVBUS O/P Drive SWBST 300 mA Boost Input Pin To Enables & Control Registers VCORE VBUSEN O/P Drive Package Pin Legend Output Pin REFCORE GNDCORE SW1IN SW1OUT GNDSW1 SW1FB DVS CONTROL To SPI CFM VCOREDIG O/P Drive Figure 2. MC13892 Simplified Internal Block Diagram MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 3 PIN CONNECTIONS PIN CONNECTIONS 1 2 3 4 5 6 7 8 9 10 11 12 13 A VUSB2 VUSB2 VINUSB2 SWBSTIN GNDSWBST GNDBL NC MODE VCORE BATT CHRGRAW CHRGCTRL2 CHRGCTRL2 B VUSB2 GPO1 DVS2 SWBSTOUT LEDB LEDKP LEDR GNDCORE VCOREDIG BP CHRGCTRL1 BATTISNSCC CHRGCTRL2 Regulators C VINPLL VSDDRV CHRGISNS BATTISNS Switchers D VUSB VSD SWBSTFB LEDMD DVS1 REFCORE CHRGSE1B LICELL BATTFET BPSNS PWRON1 E UVBUS VPLL LEDG GNDLED UID PUMS2 GNDCHRG CHRGLED PWRON2 ADTRIG INT GNDSW1 Control Logic F GNDSW3 VBUSEN SW3FB LEDAD GNDSUB GNDSUB GNDSUB GPO3 GPO2 RESETBMCU RESETB SW1OUT Charger G SW3OUT VINUSB SW4FB GNDREG2 GNDSUB GNDSUB GNDSUB PUMS1 WDI GPO4 SW1IN H SW3IN MISO GNDSPI GNDREG3 GNDSUB GNDSUB GNDSUB GNDCTRL SW1FB STANDBYSEC SW2IN J SW4IN MOSI CLK32KMCU STANDBY GNDADC GNDREG1 PWRON3 TSX1 SW2FB TSX2 SW2OUT Backlights RTC Grounds USB ADC K SW4OUT SPIVCC PWGTDRV1 CLK32K VCAM CFP CFM ADIN5 ADIN6 VVIDEODRV GNDSW2 SPI/I2C L GNDSW4 CS TSY2 VVIDEO No Connect M VGEN3 CLK VGEN2 VSRTC GNDRTC VINCAMDRV PWGTDRV2 VDIG VINDIG VGEN1DRV ADIN7 TSY1 TSREF N VGEN3 VGEN3 VINGEN3DRV VGEN2DRV XTAL2 XTAL1 VINAUDIO VAUDIO VIOHI VINIOHI VGEN1 TSREF TSREF Figure 3. MC13892VK Pin Connections MC13892 4 Analog Integrated Circuit Device Data Freescale Semiconductor PIN CONNECTIONS 1 A 2 3 4 5 6 7 8 9 10 11 12 13 VUSB2 VINUSB2 SWBSTOUT SWBSTIN GNDSUB NC MODE VCORE BATT CHRGRAW CHRGCTRL2 CHRGISNS 14 Regulators B VSDDRV GPO1 GNDSUB GNDSUB LEDR UID DVS1 REFCORE GNDCORE CHRGSE1B BP GNDCHRG BATTISNSCC BATTISNS Switchers C VSD DVS2 SWBSTFB LEDB LEDG LEDKP LEDAD PUMS2 VCOREDIG LICELL BATTFET BPSNS GPO3 PUMS1 Backlights D VUSB VPLL GNDSUB GNDSUB GNDSWBST GNDLED LEDMD GNDBL CHRGCTRL1 CHRGLED PWRON1 PWRON3 ADTRIG GPO4 Control Logic E UVBUS GNDREG2 VINPLL GNDSUB GNDSUB GNDSUB GNDSUB GNDSUB GNDSUB GNDSUB PWRON2 GPO2 INT RESETBMCU Charger F SW3OUT VBUSEN VINUSB GNDSUB GNDSUB GNDSUB GNDSUB GNDSUB GNDSUB GNDSUB GNDCTRL WDI RESETB SW1OUT RTC G GNDSW3 GNDSW3 SW3FB GNDSUB GNDSUB GNDSUB GNDSUB GNDSUB GNDSUB GNDSUB GNDSUB SW1FB GNDSW1 GNDSW1 Grounds H SW3IN SW3IN GNDSUB GNDSUB GNDSUB GNDSUB GNDSUB GNDSUB GNDSUB GNDSUB SW1IN SW1IN USB J SW4IN SW4IN SW4FB GNDSUB GNDSUB GNDSUB GNDSUB GNDSUB GNDSUB SW2FB SW2IN SW2IN ADC K GNDSW4 GNDSW4 SPIVCC GNDSUB GNDSUB GNDSUB GNDSUB GNDSUB GNDSUB VVIDEODRV GNDSW2 GNDSW2 SPI/I2C L SW4OUT CS GNDSPI GNDSUB GNDSUB GNDSUB VCAM VINAUDIO VDIG GNDSUB TSY2 STANDBYSEC VVIDEO SW2OUT No Connect M CLK VINGEN3DRV CLK32KMCU CLK32K VSRTC STANDBY VINCAMDRV CFP CFM VGEN1DRV VGEN1 TSX1 TSX2 TSY1 N VGEN3 MOSI VGEN2 GNDREG3 XTAL2 XTAL1 VAUDIO PWGTDRV2 VIOHI VINIOHI GNDADC ADIN5 ADIN7 TSREF MISO PWGTDRV1 VGEN2DRV GNDSUB GNDRTC GNDSUB GNDSUB GNDSUB GNDSUB VINDIG GNDREG1 ADIN6 P Figure 4. MC13892VL Pin Connections MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 5 PIN CONNECTIONS Table 2. MC13892 Pin Definitions A functional description of each pin can be found in the Functional Description. Pin Number Pin Number on on the the 13982VL 13982VK 12x12 mm 7x7 mm Pin Name Rating Pin Function (V) Formal Name Definition Output regulator for USB PHY A1, A2, B1 A2 VUSB2 3.6 Output USB 2 Supply A3 A3 VINUSB2 5.5 Power USB 2 Supply Input A4 A5 SWBSTIN 5.5 Power Switcher Boost Power Switcher BST input Input A5 D5 GNDSWBST - Ground Switcher Boost Ground Ground for switcher BST A6 D8 GNDBL - Ground Backlight LED Ground Ground for serial LED drive A7 A7 NC - - No Connect A8 A8 MODE 9.0 Input Mode Configuration USB LBP mode, normal mode, test mode selection,& anti-fuse bias A9 A9 VCORE 3.6 Output Core Supply Regulated supply output for the IC analog core circuitry A10 A10 BATT 5.5 Input Battery Connection Input regulator VUSB2 Do not connect 1. Battery positive pin 2. Battery current sensing point 2 3. Battery supply voltage sense A11 A11 CHRGRAW 20 I/O Charger Input 1. Charger input 2. Output to battery supplied accesories A12, A13, B13 A12 CHRGCTRL2 5.5 Output Charger Control 2 Driver output for charger path FETs M2 B2 B2 GPO1 3.6 Output General Purpose Output 1 General purpose output 1 B3 C2 DVS2 3.6 Input Dynamic Voltage Scaling Control 2 Switcher 2 DVS input pin B4 A4 SWBSTOUT 7.5 Power B5 C4 LEDB 7.5 Input LED Driver General purpose LED current sink driver Blue B6 C6 LEDKP 28 Input LED Driver Keypad lighting LED current sink driver B7 B5 LEDR 7.5 Input LED Driver General purpose LED current sink driver Red B8 B9 GNDCORE - Ground Core Ground B9 C9 VCOREDIG 1.5 Output Digital Core Supply B10 B11 BP 5.5 Power Battery Plus Switcher Boost Output Switcher BST BP supply Ground for the IC core circuitry Regulated supply output for the IC digital core circuitry 1. Application supply point 2. Input supply to the IC core circuitry 3. Application supply voltage sense Charger Control 1 Driver output for charger path FETs M1 B11 D9 CHRGCTRL1 20 Output B12 B13 BATTISNSCC 4.8 Input C1 E3 VINPLL 5.5 Power PLL Supply Input Input regulator processor PLL C2 B1 VSDDRV 5.5 Output VSD Driver Drive output regulated SD card C12 A13 CHRGISNS 4.8 Input Charger Current Sense Charge current sensing point 1 C13 B14 BATTISNS 4.8 Input Battery Current Sense Battery current sensing point 1 Battery Current Sense Accumulated current counter current sensing point MC13892 6 Analog Integrated Circuit Device Data Freescale Semiconductor PIN CONNECTIONS Table 2. MC13892 Pin Definitions (continued) A functional description of each pin can be found in the Functional Description. Pin Number Pin Number on on the the 13982VL 13982VK 12x12 mm 7x7 mm Pin Name Rating Pin Function (V) Formal Name Definition USB transceiver regulator output D1 D1 VUSB 3.6 Output USB Supply D2 C1 VSD 3.6 Output SD Card Supply Output regulator SD card D4 C3 SWBSTFB 3.6 Input Switcher Boost Feedback Switcher BST feedback D5 D7 LEDMD 28 Input LED Driver D6 B7 DVS1 3.6 Input Dynamic Voltage Scaling Control 1 Switcher 1DVS input pin D7 B8 REFCORE 3.6 Output Core Reference Main bandgap reference D8 B10 CHRGSE1B 3.6 Input Charger Select Charger forced SE1 detection input D9 C10 LICELL 3.6 I/O Coin Cell Connection Main display backlight LED current sink driver 1. Coin cell supply input 2. Coin cell charger output D10 C11 BATTFET 4.8 Output Battery FET Connection D12 C12 BPSNS 4.8 Input Battery Plus Sense Driver output for battery path FET M3 1. BP sense point 2. Charge current sensing point 2 D13 D11 PWRON1 3.6 Input Power On 1 Power on/off button connection 1 E1 E1 UVBUS 20 I/O USB Bus 1. USB transceiver cable interface 2. VBUS & OTG supply output Voltage Supply for PLL Output regulator processor PLL E2 D2 VPLL 3.6 Output E4 C5 LEDG 7.5 Input E5 D6 GNDLED - Ground LED Ground E6 B6 UID 5.5 Input USB ID E7 C8 PUMS2 3.6 Input E8 B12 GNDCHRG - Ground Charger Ground E9 D10 CHRGLED 20 Output Charger LED Trickle LED driver output 1 E10 E11 PWRON2 3.6 Input Power On 2 Power on/off button connection 2 E11 D13 ADTRIG 3.6 Input ADC Trigger ADC trigger input E12 E13 INT 3.6 Output Interrupt Signal Interrupt to processor E13 G13, G14 GNDSW1 - Ground Switcher 1 Ground Ground for switcher 1 F1 G1, G2 GNDSW3 - Ground Switcher 3 Ground Ground for switcher 3 F2 F2 VBUSEN 3.6 Input VBUS Enable F4 G3 SW3FB 3.6 Input Switcher 3 Feedback Switcher 3 feedback F5 C7 LEDAD 28 Input Auxiliary Display LED Auxiliary display backlight LED sinking current driver F6 A6, B3, B4, D3, D4, E4, E5, E6 GNDSUB1 - Ground Ground 1 PWM Driver for Green General purpose LED current sink driver Green LED Ground for LED drivers USB OTG transceiver cable ID Power Up Mode Select Power up mode supply setting 2 2 Ground for charger interface External VBUS enable pin for OTG supply Non critical signal ground and thermal heat sink MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 7 PIN CONNECTIONS Table 2. MC13892 Pin Definitions (continued) A functional description of each pin can be found in the Functional Description. Pin Number Pin Number on on the the 13982VL 13982VK 12x12 mm 7x7 mm Pin Name Rating Pin Function (V) Formal Name Definition F7 E7, E8, E9, E10, F4, F5, F6 GNDSUB2 - Ground Ground 2 Non critical signal ground and thermal heat sink F8 F7, F8, F9, F10, G4, G5, G6, G7, G8 GNDSUB3 - Ground Ground 3 Non critical signal ground and thermal heat sink F9 C13 GPO3 - Output General Purpose Output 3 General purpose output 3 F10 E12 GPO2 3.6 Output General Purpose Output 2 General purpose output 2 F11 E14 RESETBMCU 3.6 Output MCU Reset Reset output for processor F12 F13 RESETB 3.6 Output Peripheral Reset Reset output for peripherals F13 F14 SW1OUT 5.5 Output Switcher 1 Output Switcher 1 output G1 F1 SW3OUT 5.5 Output Switcher 3 Output Switcher 3 output G2 F3 VINUSB 7.5 Input VUSB Supply Input G4 J3 SW4FB 3.6 Input Switcher 4 Feedback Switcher 4 feedback G5 E2 GNDREG2 - Ground Regulator 2 Ground Ground for regulators 2 G6 G9, G10, G11, H3, H5, H6, H7, H8 GNDSUB4 - Ground Ground 4 Non critical signal ground and thermal heat sink G7 H9, H10, H12, J5, J6, J7 GNDSUB5 - Ground Ground 5 Non critical signal ground and thermal heat sink G8 J8, J9, J10, K4, K5, K6, K7 GNDSUB6 - Ground Ground 6 Non critical signal ground and thermal heat sink G9 C14 PUMS1 3.6 Input G10 F12 WDI 3.6 Input Watchdog Input Watchdog input G12 D14 GPO4 3.6 Output General Purpose Output 4 General purpose output 4 G13 H13, H14 SW1IN 5.5 Input Switcher 1 Input Input voltage for switcher 1 H1 H1, H2 SW3IN 5.5 Power Switcher 3 Input Switcher 3 input H2 P2 MISO 3.6 I/O Master In Slave Out Primary SPI read output H4 L3 GNDSPI - Ground SPI Ground Ground for SPI interface H5 N4 GNDREG3 - Ground Regulator 3 Ground Ground for regulators 3 H6 K8, K10, L4, L5, L6, L10 GNDSUB7 - Ground Ground 7 Non critical signal ground and thermal heat sink H7 P5, P7, P8, P9, P10 GNDSUB8 - Ground Ground 8 Non critical signal ground and thermal heat sink H8 - GNDSUB9 - Ground Ground 9 Non critical signal ground and thermal heat sink H9 F11 GNDCTRL - Ground Logic Control Ground Input option for UVUSB; tie to SWBST at top level Power Up Mode Select Power up mode supply setting 1 1 Ground for control logic MC13892 8 Analog Integrated Circuit Device Data Freescale Semiconductor PIN CONNECTIONS Table 2. MC13892 Pin Definitions (continued) A functional description of each pin can be found in the Functional Description. Pin Number Pin Number on on the the 13982VL 13982VK 12x12 mm 7x7 mm Pin Name Rating Pin Function (V) Formal Name Definition Switcher 1 feedback H10 G12 SW1FB 3.6 Input Switcher 1 Feedback H12 L12 STANDBYSEC 3.6 Input Secondary Standby Signal H13 J13, J14 SW2IN 5.5 Input Switcher 2 Input Input voltage for Switcher 2 J1 J1, J2 SW4IN 5.5 Power Switcher 4 Input Switcher 4 input J2 N2 MOSI 3.6 Input Master Out Slave In J4 M3 CLK32KMCU 3.6 Output J5 M6 STANDBY 3.6 Input Standby Signal J6 N11 GNDADC - Ground ADC Ground J7 P12 GNDREG1 - Ground Regulator 1 Ground J8 D12 PWRON3 3.6 Input Power On 3 J9 M12 TSX1 3.6 Input Touch Screen Interface X1 J10 J12 SW2FB 3.6 Input Switcher 2 Feedback J12 M13 TSX2 3.6 Input Touch Screen Interface X2 J13 L14 SW2OUT 5.5 Output Switcher 2 Output Switcher 2 output K1 L1 SW4OUT 5.5 Output Switcher 4 Output Switcher 4 output K2 K3 SPIVCC 3.6 Input K4 P3 PWGTDRV1 4.8 Output Power Gate Driver 1 K5 M4 CLK32K 3.6 Output 32 kHz Clock K6 L7 VCAM 3.6 Output Camera Supply K7 M8 CFP 4.8 Passive Current Filter Positive K8 M9 CFM 4.8 Passive Current Filter Negative Accumulated current filter cap minus pin K9 N12 ADIN5 4.8 Input ADC Channel 5 Input ADC generic input channel 5 K10 P13 ADIN6 4.8 Input ADC Channel 6 Input ADC generic input channel 6 K12 K12 VVIDEODRV 5.5 Output VVIDEO Driver K13 K13, K14 GNDSW2 - Ground Switcher 2 Ground Ground for switcher 2 L1 K1, K2 GNDSW4 - Ground Switcher 4 Ground Ground for switcher 4 L2 L2 CS 3.6 Input Chip Select L12 L11 TSY2 3.6 Input Touch Screen Interface Y2 Touch screen interface Y2 L13 L13 VVIDEO 3.6 Output Video Supply Output regulator TV DAC M1, N1, N2 N1 VGEN3 3.6 Output General Purpose Regulator 3 Output GEN3 regulator M2 M1 CLK 3.6 Input Clock Primary SPI clock input M3 N3 VGEN2 3.6 Output General Purpose Regulator 2 Output GEN2 regulator Standby input signal from peripherals Primary SPI write input 32 kHz Clock for MCU 32 kHz clock output for processor Standby input signal from processor Ground for A to D circuitry Ground for regulators 1 Power on/off button connection 3 Touch screen interface X1 Switcher 2 feedback Touch screen interface X2 Supply Voltage for SPI Supply for SPI bus and audio bus Power gate driver 1 32 kHz clock output for peripherals Output regulator camera Accumulated current filter cap plus pin Drive output regulator VVIDEO Primary SPI select input MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 9 PIN CONNECTIONS Table 2. MC13892 Pin Definitions (continued) A functional description of each pin can be found in the Functional Description. Pin Number Pin Number on on the the 13982VL 13982VK 12x12 mm 7x7 mm Pin Name Rating Pin Function (V) Formal Name Definition Output regulator for SRTC module on processor M4 M5 VSRTC 3.6 Output SRTC Supply M5 P6 GNDRTC - Ground Real Time Clock Ground M6 M7 VINCAMDRV 5.5 I/O M7 N8 PWGTDRV2 4.8 Output Power Gate Driver 2 M8 L9 VDIG 3.6 Output Digital Supply M9 P11 VINDIG 5.5 Input VDIG Supply Input M10 M10 VGEN1DRV 5.5 Output VGEN1 Driver M11 N13 ADIN7 4.8 Input ADC Channel 7 Input M12 M14 TSY1 3.6 Input Touch Screen Interface Y1 Touch screen interface Y1 M13, N12, N13 N14 TSREF 3.6 Output Touch Screen Reference Touch screen reference N3 M2 VINGEN3DRV 5.5 Ground for the RTC block 1. Input regulator camera using internal Camera Regulator Supply Input and Driver PMOS FET. Output 2. Drive output regulator for camera voltage using external PNP device. Power/Output VGEN3 Supply Input and Driver Output Power gate driver 2 Output regulator digital Input regulator digital Drive output GEN1 regulator ADC generic input channel 7, group 1 1. Input VGEN3 regulator 2. Drive VGEN3 output regulator Drive output GEN2 regulator N4 P4 VGEN2DRV 5.5 Output VGEN2 Driver N5 N5 XTAL2 2.5 Input Crystal Connection 2 32.768 kHz oscillator crystal connection 2 N6 N6 XTAL1 2.5 Input Crystal Connection 1 32.768 kHz oscillator crystal connection 1 N7 L8 VINAUDIO 5.5 Power Audio Supply Input N8 N7 VAUDIO 3.6 Output Audio Supply N9 N9 VIOHI 3.6 Output N10 N10 VINIOHI 5.5 Input N11 M11 VGEN1 3.6 Output Input regulator VAUDIO Output regulator for audio High Voltage IO Supply Output regulator high voltage IO, efuse High Voltage IO Supply Input regulator high voltage IO Input General Purpose Regulator 1 Input GEN1 regulator MC13892 10 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS MAXIMUM RATINGS ELECTRICAL CHARACTERISTICS MAXIMUM RATINGS Table 3. Maximum Ratings All voltages are with respect to ground unless otherwise noted. Exceeding these ratings may cause a malfunction or permanent damage to the device. Ratings Symbol Value Unit Charger and USB Input Voltage(5) VCHRGR -0.3 to 20 V MODE pin Voltage VMODE -0.3 to 9.0 V VLEDMD, VLEDAD, VLEDKP -0.3 to 28 V VBATT -0.3 to 4.8 V VLICELL -0.3 to 3.6 V ELECTRICAL RATINGS Main/Aux/Keypad Current Sink Voltage Battery Voltage Coin Cell Voltage ESD Voltage(6) VESD Human Body Model - HBM with Mode pin excluded(9) Charge Device Model - CDM V 1500 250 THERMAL RATINGS Ambient Operating Temperature Range TA -40 to +85 C Operating Junction Temperature Range TJ -40 to +125 C TSTG -65 to +150 C TPPRT Note 8 C Storage Temperature Range THERMAL RESISTANCE Peak Package Reflow Temperature During Reflow(7), (8) Notes 5. USB Input Voltage applies to UVBUS pin only 6. ESD testing is performed in accordance with the Human Body Model (HBM) (CZAP = 100 pF, RZAP = 1500 ) and the Charge Device Model (CDM), Robotic (CZAP = 4.0 pF). 7. Pin soldering temperature limit is for 10 seconds maximum duration. Not designed for immersion soldering. Exceeding these limits may cause malfunction or permanent damage to the device. 8. Freescale's Package Reflow capability meets Pb-free requirements for JEDEC standard J-STD-020C. For Peak Package Reflow Temperature and Moisture Sensitivity Levels (MSL), Go to www.freescale.com, search by part number [e.g. remove prefixes/suffixes and enter the core ID to view all orderable parts. (i.e. MC33xxxD enter 33xxx), and review parametrics. 9. Mode Pin is not ESD protected. Table 4. Dissipation Ratings Rating Parameter Condition Symbol VK Package VL Package Unit Junction to Ambient Natural Convection Single layer board (1s) RJA 104 65 C/W Junction to Ambient Natural Convection Four layer board (2s2p) RJMA 54 42 C/W Junction to Ambient (@200 ft/min) Single layer board (1s) RJMA 88 55 C/W Junction to Ambient (@200 ft/min) Four layer board (2s2p) RJMA 49 38 C/W Junction to Board RJB 32 28 C/W Junction to Case RJC 29 22 C/W JT 7.0 5.0 C/W Junction to Package Top Natural Convection MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 11 ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 5. Static Electrical Characteristics Characteristics noted under conditions - 40 C TA 85 C, GND = 0 V unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25 C under nominal conditions, unless otherwise noted. Characteristic Symbol RTC Mode All blocks disabled, no main battery attached, coin cell is attached to IRTC Min Typ Max Unit CURRENT CONSUMPTION LICELL (10) RTC OFF Mode (All blocks disabled, main battery attached) (10) MC13892 core and RTC module IOFF Power Cut Mode (All blocks disabled, no main battery attached, coin cell is attached and valid) (10) MC13892 core and RTC module IPCUT A - 3.00 6.00 - 10 30 A A - 3.0 6.0 ISTBY - 230 295 ION - 459 1500 PWRON1, PWRON2, PWRON3, Pull-up (14) Input Low, 47 kOhm Input High, 1.0 MOhm 0.0 - 0.3 1.0 - VCOREDIG CHRGSE1B, Pull-up (15) Input Low Input High 0.0 - 0.3 1.0 - VCORE STANDBY, STANDBYSEC, WDI, ADTRIG, Weak Pull-down (16),(17) Input Low Input High 0.0 - 0.3 1.0 - 3.6 CLK32K, CMOS Output Low, -100 A Output High, 100 A 0.0 - 0.2 SPIVCC -0.2 - SPIVCC 0.0 - 0.2 VSRTC- 0.2 - VSRTC 0.0 - 0.4 0.0 - 3.6 ON Standby mode - Low-power mode 4 buck regulators in low-power mode, 3 regulators (11) A ON Mode - Typical use case 4 buck regulators in PWMPS mode, 5 Regulators (12) A I/O CHARACTERISTICS (13) CLK32KMCU, CMOS Output Low, -100 A Output High, 100 A RESETB, RESETBMCU, Open Drain (18) Output Low, -2.0 mA Output High, Open Drain Notes 10. 11. 12. 13. 14. 15. 16. 17. 18. V V V V V V Valid at 25 C only. VPLL, VIOHI, VGEN2 VPLL, VIOHI, VGEN2, VAUDIO, VVIDEO SPIVCC is typically connected to the output of buck regulator: SW4 and set to 1.800 V Input has internal pull-up to VCOREDIG equivalent to 200 kOhm Input has internal pull-up to VCORE equivalent to 100 kOhm SPIVCC needs to remain enabled for proper detection of WDI High to avoid involuntary shutdown A weak pull-down represents a nominal internal pull down of 100 nA, unless otherwise noted RESETB & RESETBMCU have open drain outputs, external pull-ups are required MC13892 12 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 5. Static Electrical Characteristics (continued) Characteristics noted under conditions - 40 C TA 85 C, GND = 0 V unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25 C under nominal conditions, unless otherwise noted. Characteristic Symbol Min Typ Max Unit 1.1 - 1.3 V 0.0 - 0.3* SPIVCC 0.7* SPIVCC - 3.1 0.0 - 0.2 VCORE- 0.2 - VCORE 200 - 500 I/O CHARACTERISTICS (CONTINUED) (19) VSRTC, Voltage Output DVS1, DVS2, Weak Pull-down Input Low Input High V (20) GPO1, CMOS Output Low, -400 A Output High, 400 A To VCORE GPO2, GPO3, GPO4, CMOS Output Low, -100 A Output High, 100 A GPO4, Analog Input CS, CLK, MOSI, VBUSEN, Weak Pull-down on CS and VBUSEN (20) Input Low Input High CS, MOSI (at Booting for SPI / I2C decoding), Weak Pull-down on CS (21) Input Low Input High MISO, INT, CMOS (22) Output Low, -100 A Output High, 100 A V 0.0 - 0.2 VIOHI - 0.2 0.0 - - VIOHI VCORE+0.3 0.0 - 0.3* SPIVCC 0.7* SPIVCC - SPIVCC+0.3 0.0 - 0.3 * VCORE 0.7 * VCORE - VCORE 0.0 - 0.2 SPIVCC -0.2 - SPIVCC 0.0 - 0.3 Open - Open 1.3 - 2.0 2.5 - MODE (23) Input Low Input Med Input High 3.1 0.0 - 0.4 1.1 - 1.7 VCORE - 9.0 V V V V V (22) PUMS1, PUMS2 PUMSxS = 00 PUMSxS = 01, Load < 10 pF PUMSxS = 10 PUMSxS = 11 Ohm V V Notes 19. SPIVCC is typically connected to the output of buck regulator: SW4 and set to 1.800 V 20. A weak pull-down represents a nominal internal pull down of 100 nA unless otherwise noted 21. 22. 23. 24. The weak pull-down on CS is disabled if a VIH is detected at startup to avoid extra consumption in I2C mode The output drive strength is programmable Input state is latched in first phase of cold start, refer to Power Control System for description of PUMS configuration Input state is not latched MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 13 ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 5. Static Electrical Characteristics (continued) Characteristics noted under conditions - 40 C TA 85 C, GND = 0 V unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25 C under nominal conditions, unless otherwise noted. Characteristic Symbol Min Typ Max 1.2 - 4.65 1.8 - 2.0 0.0 - 0.2 Unit 32 KHZ CRYSTAL OSCILLATOR Operating Voltage Oscillator and RTC Block from BP VXTAL Coincell Disconnect Threshold At LICELL VLCD V V Output Low CLK32K, CLK32KMCU Output sink 100 A VCLKLO Output High CLK32K Output source 100 A CLK32KMCU Output source 100 A VCLKHI VCLKMCUHI SPIVCC-0.2 VSRTC-0.2 - - SPIVCC VSRTC VLICELL BP 1.8 UVDET - - 3.6 4.65 Operating Current Load Range ILMIN to ILMAX ISRTC 0.0 - 50 A Bypass Capacitor Value CSRTC - 1.0 - F 1.15 1.20 1.25 VINCSLO VINMOSILO VINCLKLO 0.0 - 0.3*SPIVCC VINCSHI VINMOSIHI VINCLKHI 0.7*SPIVCC - SPIVCC+0.3 0.0 - 0.2 VOMISOHI VOINTHI SPIVCC-0.2 - SPIVCC SPIVCC 1.75 - 3.1 V V VSRTC GENERAL Operating Input Voltage Range VINMIN to VINMAX Valid Coin Cell range Or valid BP V VSRTC ACTIVE MODE - DC Output Voltage VOUT VINMIN < VIN < VINMAX, ILMIN < IL < ILMAX VSRTC V CLK AND MISO Input Low CS, MOSI, CLK Input High CS, MOSI, CLK Output Low MISO, INT Output sink 100 A Output High MISO, INT Output source 100 A SPIVCC Operating Range VOMISOLO VOINTLO V V V V V MC13892 14 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 5. Static Electrical Characteristics (continued) Characteristics noted under conditions - 40 C TA 85 C, GND = 0 V unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25 C under nominal conditions, unless otherwise noted. Characteristic Symbol Min Typ Max 3.0 2.8 UVDET - - - 4.65 4.65 4.65 0.6 0.6 - - 1.375 1.850 VSWLOPP VSWLIPPI Nom-50 Nom-50 Nom Nom Nom+50 Nom+50 ISW1 ISW1, 2, 3, 4 800 1050 800 800 - - - - - 50 - - - - - ISW1 ISW4 1250 1000 - - - - Unit BUCK REGULATORS Operating Input Voltage PWM operation, 0 < IL < IMAX PFM operation, 0 < IL < IMAX VSWIN Extended PWM or PFM operation(25) Output Voltage Range Switcher 1 Switchers 2, 3, and 4 VSW1 V V Output Accuracy mV PWM mode including ripple, load regulation, and transients (26) PFM Mode, including ripple, load regulation, and transients Maximum Continuous Load Current, IMAX, VINMIN<BP<4.65 V SW1 in PWM mode (SWILIMB = 0, no max current limit) SW1 in PWM Mode (SWILIMB = 1, no max current limit)(27) SW2, SW3, SW4 in PWM mode (SWILIMB = 0, no max current limit) SW2, SW3, SW4 in PWM mode (SWILIMB = SW1, SW2, SW3, SW4 in PFM mode 1, no max current limit)(27) mA ISW2,3,4 ISW2,3,4 Maximum Peak Load Current, IPEAK, BP 4.2 V, SW1 in PWM Mode (SWILIMB = 1, no max current limit)(27) SW4 in PWM Mode (SWILIMB = 1, no max current limit)(27) mA Notes 25. In the extended operating range the performance may be degraded 26. Transient loading for load steps of ILmax/2 27. In this mode, current limit protection is disabled for SW1 - SW4 by setting SWILIMB = 1. Therefore, the load on SW1-4 should not exceed the conditions specified in the table above. Application needs to provide current limit protection circuitry either in battery or as preregulated supply to BP. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 15 ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 5. Static Electrical Characteristics (continued) Characteristics noted under conditions - 40 C TA 85 C, GND = 0 V unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25 C under nominal conditions, unless otherwise noted. Characteristic Symbol Min Typ Max - 50 - - - - - - - 75 85 78 82 78 82 - - - - - - -20% -30% - -35% -35% 5.0 1.0 2.2 1.5 - 10 2x22 - 4.7 +20% +30% 0.16 +35% +35% 50 - Nom-5% 5.0 Nom+5% - - 120 - - 0.5 - - 50 Unit BUCK REGULATORS (CONTINUED) Automatic Mode Change Threshold, Switchover between PFM and PWM modes AMCTH Efficiency PFM, 0.9 V, 1.0 mA PFM, 01.8 V, 1.0 mA PWM Pulse Skipping, 1.25 V, 50 mA PWM Pulse Skipping, 1.8 V, 50 mA PWM, 1.25 V, 500 mA PWM, 1.8 V, 500 mA mA External Components, Used as a condition for all other parameters Inductor for SW2, SW3, SW4(28) Inductor for SW1(28) Inductor Resistance Bypass Capacitor for SW2, SW3, SW4(29) Bypass Capacitor for SW1(30) Bypass Capacitor ESR LSW234 LSW1 RWSW COSW234 COSW1 ESRSW Input Capacitor(31) H H F F m F SWBST Average Output Voltage(32) 3.0 V < VIN < 4.65 (1), 0 < IL < ILMAX(33) VBST Output Ripple 3.0 V < VIN < 4.65, 0 < IL < ILMAX, Excluding reverse recovery of Schottky diode VBSTPP Average Load Regulation VIN = 3.6 V, 0 < IL < ILMAX VBSTLOR Average Line Regulation 3.0 V < VIN < 4.65 V, IL = ILMAX VBSTLIR V mVpp mV/mA mV Notes 28. Preferred device TDK VLS252012 series at 2.5x2.0 mm footprint and 1.2 mm max height 29. Preferably 0603 style 6.3 V rated X5R/X7R type at 35% total make tolerance, temperature spread and DC bias derating such as TDK C1608X5R0J106M 30. Preferably 0805 style 6.3 V rated X5R/X7R type at 35% total make tolerance, temperature spread and DC bias derating such as TDK C2012X5R0J226M 31. Preferably 0603 style 6.3 V rated X5R/X7R type at 35% total make tolerance, temperature spread and DC bias derating such as TDK C1608X5R0J475 32. Output voltage when configured to supply VBUS in OTG mode can be as high as 5.75 V 33. Vin is the low side of the inductor that is connected to BP. MC13892 16 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 5. Static Electrical Characteristics (continued) Characteristics noted under conditions - 40 C TA 85 C, GND = 0 V unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25 C under nominal conditions, unless otherwise noted. Characteristic Symbol Min Typ Max Unit 300 - - - - 500 SWBSTEFF - 80 - % LBST R_WBST ILSAT COBST ESRBST CBSTD IBSTDPK IBSTDPK -20% - 1.0 -60% 1.0 1.0 850 1500 2.2 - - 10 - 4.7 - - +20% 0.2 - +35% 10 - - - H A F m F mAdc mApk IBSTIK - 1.0 5.0 A VINVIDEO VNOM+0.25 - 4.65 V Operating Current Load Range ILMIN to ILMAX (Not exceeding PNP max power) IVIDEO 0.0 - 350 mA Minimum Bypass Capacitor Value Used as a condition for all other parameters COVIDEO 1.1 2.2 - Bypass Capacitor ESR 10 kHz -1.0 MHz ESRVIDEO 20 - 100 VNOM - 3% VNOM VNOM + 3% - - 0.20 - 5.0 8.0 ILMAX+20% - - SWBST (CONTINUED) Maximum Continuous Load Current ILMAX 3.0 V < VIN < 4.65, VOUT = 5.0 V Start-up Overshoot IL = 0 mA Efficiency, IL = ILMAX IBST VBSTOS mA mV External Components - Used as a condition for all other parameters Inductor(34) Inductor Resistance Inductor saturation current at 30% loss in inductance value Bypass Capacitor(35) Bypass Capacitor ESR at resonance Input Capacitor Diode current capability Diode current capability NMOS Off Leakage, SWBSTIN = 4.5 V, SWBSTEN = 0 VVIDEO Operating Input Voltage Range VINMIN to VINMAX F m VVIDEO ACTIVE MODE DC Output Voltage VOUT VINMIN < VIN < VINMAX, ILMIN < IL < ILMAX VVIDEO Load Regulation 1.0 mA < IL < ILMAX, For any VINMIN < VIN < VINMAX VVIDEOLOPP Line Regulation VINMIN < VIN < VINMAX, For any ILMIN < IL < ILMAX VVIDEOLIPP Short-circuit Protection Threshold VINMIN < VIN < VINMAX, Short-circuit VOUT to GND IVIDEOSHT V mV/mA mV mA Notes 34. Preferred device TDK VLS252012 series at 2.5x2.0 mm footprint and 1.2 mm max height 35. Applications of SWBST should take into account impact of tolerance and voltage derating on the bypass capacitor at the output level. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 17 ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 5. Static Electrical Characteristics (continued) Characteristics noted under conditions - 40 C TA 85 C, GND = 0 V unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25 C under nominal conditions, unless otherwise noted. Characteristic Symbol Min Typ Max Unit VNOM -3% VNOM VNOM +3% IVIDEOLO 0.0 - 3.0 Operating Input Voltage Range VINMIN to VINMAX VAUDIO VNOM+0.25 - 4.65 V Operating Current Load Range ILMIN to ILMAX IAUDIO 0.0 - 150 mA COAUDIO 0.65 2.2 - F 0.0 - 0.1 VVIDEO LOW-POWER MODE DC - VVIDEOMODE = 1 Output Voltage VOUT VINMIN < VIN < VINMAX, ILMINLP < IL < ILMAXLP Current Load Range ILminlp to ILMAXLP VVIDEOLO V mA VAUDIO Minimum Bypass Capacitor Value Bypass Capacitor ESR 10 kHz -1.0 MHz ESRAUDIO VAUDIO ACTIVE MODE DC Output Voltage VOUT (VINMIN < VIN < VINMAX, ILMIN < IL < ILMAX) VAUDIO VNOM - 3% VNOM VNOM + 3% V Load Regulation (1.0 mA < IL < ILMAX, For any VINMIN < VIN < VINMAX) VAUDIOLOR - - 0.25 mV/mA Line Regulation VINMIN < VIN < VINMAX, For any ILMIN < IL < ILMAX VAUDIOLIR - 5.0 8.0 Short-circuit Protection Threshold VINMIN < VIN < VINMAX, Short-circuit VOUT to GND IAUDIOSHT ILMAX+20% - - UVDET 1.75 2.15 - SW4 = 1.8 2.2 4.65 4.65 4.65 mV mA VPLL AND VDIG Operating Input Voltage Range VINMIN to VINMAX VDIG, VPLL all settings, BP biased VPLL, VDIG [1:0] = 00,01 VPLL, VDIG [1:0] = 10, 11, External Switcher VINPLL, VINDIG V Operating Current Load Range ILMIN to ILMAX IPLL, IDIG 0.0 - 50 Minimum Bypass Capacitor Value Used as a condition for all other parameters COPLL, CODIG 0.65 2.2 - ESRPLL, ESRDIG 0.0 - 0.1 VNOM - 0.05 VNOM VNOM + 0.05 Bypass Capacitor ESR 10 kHz -1.0 MHz mA F VPLL AND VDIG ACTIVE MODE DC Output Voltage VOUT VINMIN < VIN < VINMAX, ILMIN < IL < ILMAX VPLL, VDIG V Load Regulation 1.0 mA < IL < ILMAX for any VINMIN < VIN < VINMAX VPLLLOR, VDIGLOR - - 0.35 Line Regulation VINMIN < VIN < VINMAX for any ILMIN < IL < ILMAX VPLLLIR, VDIGLIR - 5.0 8.0 VNOM+0.25 - 4.65 mV/mA mV VIOHI Operating Input Voltage Range VINMIN to VINMAX VNOM = 2.775 V Operating Current Load Range ILMIN to ILMAX Minimum Bypass Capacitor Value Bypass Capacitor ESR 10 kHz -1.0 MHz VINIOHI V IIOHI 0.0 - 100 mA COIOHI 0.65 2.2 - F 0.0 - 100 ESRIOHI m MC13892 18 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 5. Static Electrical Characteristics (continued) Characteristics noted under conditions - 40 C TA 85 C, GND = 0 V unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25 C under nominal conditions, unless otherwise noted. Characteristic Symbol Min Typ Max VNOM -3% VNOM VNOM +3% - - 0.35 - 5.0 8.0 VNOM +0.25 - 4.65 0.0 0.0 - - 65 250 0.65 1.1 2.2 2.2 - - 20 - 100 VNOM - 3% VNOM VNOM + 3% - - 0.25 - 5.0 8.0 ILMAX+20% - - VNOM -3% VNOM VNOM +3% 0.0 - 3.0 VNOM+0.25 UVDET UVDET 2.15 - - - 2.20 4.65 4.65 4.65 4.65 0.0 - 250 1.1 2.2 - 20 - 100 Unit VIOHI ACTIVE MODE DC Output Voltage VOUT - (VNOM = 2.775) VINMIN < VIN < VINMAX, ILMIN < IL < ILMAX VIOH Load Regulation 1.0 mA < IL < ILMAX, for any VINMIN < VIN < VINMAX VIOHLOR Line Regulation VINMIN < VIN < VINMAX, for any ILMIN < IL < ILMAX VIOHLIR V mV/mA mV VCAM Operating Input Voltage Range VINMIN to VINMAX Operating Current Load Range ILMIN to ILMAX Internal pass FET External PNP Minimum Bypass Capacitor Value Internal pass device External PNP (not exceeding PNP max power) Bypass Capacitor ESR 10 kHz -1.0 MHz VINCAM ICAM COCAM ESRCAM V mA F m VCAM ACTIVE MODE DC Output Voltage VOUT (VNOM = 2.775) VINMIN < VIN < VINMAX, ILMIN < IL < ILMAX VCAM Load Regulation 1.0 mA < IL < ILMAX, for any VINMIN < VIN < VINMAX VCAMLOR Line Regulation VINMIN < VIN < VINMAX, for any ILMIN < IL < ILMAX VCAMLIR Short-circuit Protection Threshold VINMIN < VIN < VINMAX, Short-circuit VOUT to GND ICAMSHT V mV/mA mV mA VCAM LOW-POWER MODE DC Output Voltage VOUT VINMIN < VIN < VINMAX, ILMINLP < IL < ILMAXLP VCAMLO Current Load Range ILMINLP to ILMAXLP ICAMLO V mA VSD Operating Input Voltage Range VINMIN to VINMAX VSD[2:0] = 010 to 111 VSD[2:0] = 010 to 111, Extended Operation VSD[2:0] = 000, 001 [000] BP Supplied VSD[2:0] = 000 External Switcher Supplied Operating Current Load Range ILMIN to ILMAX Not exceeding PNP max power Minimum Bypass Capacitor Value Bypass Capacitor ESR 10 kHz -1.0 MHz VINSD ISD COSD ESRSD V mA F m MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 19 ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 5. Static Electrical Characteristics (continued) Characteristics noted under conditions - 40 C TA 85 C, GND = 0 V unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25 C under nominal conditions, unless otherwise noted. Characteristic Symbol Min Typ Max Unit VNOM - 3% VNOM VNOM + 3% - - 0.25 - 5.0 8.0 ILMAX+20% - - VNOM -3% VNOM VNOM +3% 0.0 - 3.0 4.4 - 5.0 - 5.25 5.75 IUSB 0.0 - 100 mA COUSB 0.65 2.2 - F 0.0 - 0.1 VNOM - 4% 3.3 VNOM + 4% - - 1.0 - - 20 ILMAX+20% - - VINUSB2 VNOM +0.25 UVDET - - 4.65 4.65 V Operating Current Load Range ILMIN to ILMAX IUSB2 0.0 - 50 mA Minimum Bypass Capacitor Value Used as a condition for all other parameters COUSB2 0.65 2.2 - 0.0 - 0.1 VSD ACTIVE MODE DC Output Voltage VOUT VINMIN < VIN < VINMAX, ILMIN < IL < ILMAX VSD Load Regulation 1.0 mA < IL < ILMAX, for any VINMIN < VIN < VINMAX VSDLOR Line Regulation VINMIN < VIN < VINMAX, for any ILMIN < IL < ILMAX VSDLIR Short-circuit Protection Threshold VINMIN < VIN < VINMAX, Short-circuit VOUT to GND ISDSHT V mV/mA mV mA VSD LOW-POWER MODE DC - VSDMODE = 1 Output Voltage VOUT VINMIN < VIN < VINMAX, ILMINLP < IL < ILMAXLP VSDLO Current Load Range ILMINLP to ILMAXLP ISDLO V mA VUSB GENERAL Operating Input Voltage Range VINMIN to VINMAX Supplied by VBUS Supplied by SWBST Operating Current Load Range ILMIN to ILMAX Bypass Capacitor Value Range Bypass Capacitor ESR 10 kHz -1.0 MHz VINUSB ESRUSB V VUSB ACTIVE MODE DC Output Voltage VOUT VINMIN < VIN < VINMAX, ILMIN < IL < ILMAX VUSB Load Regulation 0 < IL < ILMAX from DM/DP for any VINMIN < VIN < VINMAX VUSBLOR Line Regulation VINMIN < VIN < VINMAX, for any ILMIN < IL < ILMAX VUSBLIR Short-circuit Protection Threshold VINMIN < VIN < VINMAX, Short-circuit VOUT to GND VUSBSHT V mV/mA mV mA VUSB2 Operating Input Voltage Range VINMIN to VINMAX Extended operation Bypass Capacitor ESR 10 kHz -1.0 MHz ESRUSB2 F MC13892 20 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 5. Static Electrical Characteristics (continued) Characteristics noted under conditions - 40 C TA 85 C, GND = 0 V unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25 C under nominal conditions, unless otherwise noted. Characteristic Symbol Min Typ Max VNOM -3% VNOM VNOM + 3% - - 0.35 - 5.0 8.0 4.75 5.0 5.25 100 Unit VUSB2 ACTIVE MODE DC Output Voltage VOUT VINMIN < VIN < VINMAX, ILMIN < IL < ILMAX VUSB2 Load Regulation 1.0 mA < IL < ILMAX, for any VINMIN < VIN < VINMAX VUSB2LOR Line Regulation VINMIN < VIN < VINMAX, for any ILMIN < IL < ILMAX VUSB2LIR V mV/mA mV UVBUS Operating Input Voltage Range VINMIN to VINMAX VINUSB supplied by SWBST Operating Current Load Range ILMIN to ILMAX VINUVBUS V IUVBUS 0.0 - Minimum Bypass Capacitor Value COUVBUS (36) (36) Bypass Capacitor ESR 10 kHz -1.0 MHz VINUVBUS (36) (36) (37) 4.4 5.0 5.25 UVDET < VNOM +0.25 - 4.65 2.15 2.2 4.65 0.0 - 200 UVDET - 4.65 1.1 2.2 +35% 20 - 100 VNOM - 0.05 VNOM - 3% VNOM VNOM VNOM + 0.05 VNOM + 3% - - 0.25 - 5.0 8.0 ILMAX+20% - - 6.5 (37) mA F UVBUS ACTIVE MODE DC Output Voltage Vout VINMIN < VIN < VINMAX, ILMIN < IL < ILMAX VUVBUS V VGEN1 Operating Input Voltage Range VINMIN to VINMAX All settings, BP biased VINGEN1 VGEN1=00,01, External switcher supplied Operating Current Load Range ILMIN to ILMAX (not exceeding PNP max power) IGEN1 Extended input voltage range (BP biased, performance may be out of specification for output levels VGEN1[1:0] = 10 to 11) Minimum Bypass Capacitor Value Bypass Capacitor ESR 10 kHz -1.0 MHz V mA V COGEN1 ESRGEN1 F m VGEN1 ACTIVE MODE DC Output Voltage VOUT VGEN1 = 00, 01, VINMIN < VIN < VINMAX ILMIN < IL < ILMAX VGEN1 = 10, 11, VINMIN < VIN < VINMAX ILMIN < IL < ILMAX VGEN1 Load Regulation 1.0 mA < IL < ILMAX, for any VINMIN < VIN < VINMAX VGEN1LOR Line Regulation VINMIN < VIN < VINMAX, for any ILMIN < IL < ILMAX VGEN1LIR Short-circuit Protection Threshold VINMIN < VIN < VINMAX, Short-circuit VOUT to GND VGEN1SHT V mV/mA mV mA Notes 36. Filtering is shared with CHRGRAW (shorted at board level). 2.2 F is typically included at the CHRGRAW pin. 37. 6.5 F is the maximum allowable capacitance on VBUS including all tolerances of filtering capacitance on VBUS and CHRGRAW (which are shorted at the board level). MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 21 ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 5. Static Electrical Characteristics (continued) Characteristics noted under conditions - 40 C TA 85 C, GND = 0 V unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25 C under nominal conditions, unless otherwise noted. Characteristic Symbol Min Typ Max VNOM - 0.05 VNOM -3% VNOM VNOM VNOM + 0.05 VNOM +3% Unit VGEN1 LOW-POWER MODE DC - VGEN1MODE = 1 Output Voltage VOUT - VINMIN < VIN < VINMAX, ILMINLP < IL < ILMAXLP VGEN1 = 00, 01 VGEN1 = 10, 11 VGEN1LO Current Load Range ILMINLP to ILMAXLP IGEN1LO 0.0 - 3.0 VINGEN2 UVDET< VNOM+0.25 - 4.65 2.15 2.2 4.65 IGEN2 0.0 - 350 mA COGEN2 1.1 2.2 +35% F 20 - 100 VNOM -0.05 VNOM -3% VNOM VNOM VNOM +0.05 VNOM +3% - - 0.20 - 5.0 8.0 ILMAX+20% - - VNOM -0.05 VNOM -3% VNOM VNOM VNOM +0.05 VNOM +3% 0.0 - 3.0 VNOM+0.2 UVDET - - 4.65 4.65 0.0 0.0 - - 50 200 0.65 1.1 2.2 2.2 - - 20 - 100 V mA VGEN2 GENERAL Operating Input Voltage Range VINMIN to VINMAX All settings, BP biased VGEN2=000,001, External switcher supplied Operating Current Load Range ILMIN to ILMAX (Not exceeding PNP max power) Minimum Bypass Capacitor Value Bypass Capacitor ESR 10 kHz -1.0 MHz ESRGEN2 V m VGEN2 ACTIVE MODE DC Output Voltage VOUT VGEN2 = 000, 001, 010, VINMIN < VIN < VINMAX ILMIN < IL < ILMAX VGEN2 = 011, 100, 101, 110, 111, VINMIN < VIN < VINMAX ILMIN < IL < ILMAX VGEN2 Load Regulation 1.0 mA < IL < ILMAX, For any VINMIN < VIN < VINMAX VGEN2LOR Line Regulation VINMIN < VIN < VINMAX, For any ILMIN < IL < ILMAX VGEN2LIR Short-circuit Protection Threshold VINMIN < VIN < VINMAX, Short-circuit VOUT to GND VGEN2SHT V mV/mA mV mA VGEN2 LOW-POWER MODE DC - VGEN2MODE=1 Output Voltage VOUT - VINMIN < VIN < VINMAX, ILMINLP < IL < ILMAXLP VGEN2 = 000 to 010 VGEN2 = 011 to 111 Current Load Range ILMINLP to ILMAXLP VGEN2LO IGEN2LO V mA VGEN3 GENERAL Operating Input Voltage Range VINMIN to VINMAX VGEN3CONFIG, VGEN3 = 01, 11 VGEN3CONFIG, VGEN3 = 00, 10 Operating Current Load Range ILMIN to ILMAX Internal Pass FET External PNP (Not exceeding PNP max power) Minimum Bypass Capacitor Value Internal pass device External pass device Bypass Capacitor ESR 10 kHz -1.0 MHz VINGEN3 IGEN3 COGEN3 ESRGEN3 V mA F m MC13892 22 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 5. Static Electrical Characteristics (continued) Characteristics noted under conditions - 40 C TA 85 C, GND = 0 V unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25 C under nominal conditions, unless otherwise noted. Characteristic Symbol Min Typ Max VNOM -3% VNOM VNOM + 3% - - 0.40 - 5.0 9.0 ILMAX+20% - - VNOM -3% VNOM VNOM +3% Unit VGEN3 ACTIVE MODE DC Output Voltage VOUT VGEN2 = 000, 001, 010, VINMIN < VIN < VINMAX ILMIN < IL < ILMAX VGEN3 Load Regulation 1.0 mA < IL < ILMAX, For any VINMIN < VIN < VINMAX VGEN3LOR Line Regulation VINMIN < VIN < VINMAX, For any ILMIN < IL < ILMAX VGEN3SHT Short-circuit Protection Threshold VINMIN < VIN < VINMAX, Short circuit VOUT to GND VGEN3SHT V mV/mA mV mA VGEN3 LOW-POWER MODE DC Output Voltage VOUT - (Accuracy) VINMIN < VIN < VINMAX, ILMINLP < IL < ILMAXLP VGEN3LO Current Load Range ILMINLP to ILMAXLP IGEN3LO 0.0 1.0 3.0 VINCHRG BATTMIN - 5.6 V mA CHARGE PATH REGULATOR Input Operating Voltage - CHRGRAW Output Voltage Spread - VCHRG[2:0]=011, 1XX Charge current 1.0 mA to 100 mA Charge current 100 mA and above BPSP Current Limit Tolerance (38) ICHRG[3:0] = 0001 ICHRG[3:0] = 0100 ICHRG[3:0] = 0110 All other settings ILIM V % -1.5 -3.0 - - 1.5 1.5 68 360 500 - 80 400 560 - 92 440 620 15 mA mA mA % BPOS-START v - 2.0 % CINCHRG CBP LC - 10 - 2.2 - - - 47 3.0 F F m Thermal Warning Lower Threshold TWL - 100 - C Thermal Warning Higher Threshold TWH - 120 - C Thermal Warning Hysteresis TWHYS - 3.0 - C Thermal Protection Threshold TPT - 140 - C Absolute Accuracy - All current settings - - 15 % Matching - At 400 mV, 21 mA - - 3.0 % Leakage - LEDxDC[5:0] = 000000 - - 1.0 A Absolute Accuracy - All current settings - - 15 % Matching - At 400 mV, 21 mA - - 10 % Leakage - LEDxDC[5:0] = 000000 - - 1.0 A Start-up Overshoot - Unloaded Configuration Input Capacitance - CHRGRAW(39) Load Capacitor - BPSNS(39) Cable length THERMAL BACKLIGHT LED DRIVERS SIGNALING LED DRIVERS MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 23 ELECTRICAL CHARACTERISTICS STATIC ELECTRICAL CHARACTERISTICS Table 5. Static Electrical Characteristics (continued) Characteristics noted under conditions - 40 C TA 85 C, GND = 0 V unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25 C under nominal conditions, unless otherwise noted. Characteristic Symbol Min Typ Max Unit 4.4 5.0 5.25 V 0.0 -1.2 - - 2.4 1.2 Maximum Input Voltage(40) Channels ADIN5, ADIN6 and ADIN7 - - BP Integral Nonlinearity - - 3 LSB Differential Nonlinearity - - 1 LSB Zero Scale Error (Offset) after auto calibration - - 1 LSB Full Scale Error (Gain) after auto calibration - - 5 LSB Drift Over-temperature - Including scaling - - 1 LSB Source Impedance No bypass capacitor at input Bypass capacitor at input 10 nF - - - - 5.0 30 - - VCORE V Plate Resistance X, Y 100 - 1000 Resistance Between Plates Settling Time - Contact 180 3.0 - - 1200 5.5 s ACTIVE MODE DC Output Voltage VOUT - (VNOM = 2.775), VINMIN < VIN < VINMAX, ILMIN < IL < ILMAX ADC Converter Core Input Range Single ended voltage readings Differential readings V V K TOUCH SCREEN Plate Maximum Voltage X, Y(41) Position measurement TOUCH SCREEN IN STAND ALONE MODE(42) Max Load Current - Active Mode - - 20 mA Output Voltage - 0.0<IL<20 mA -3% 1.20 +3% V 50 - - dB PSRR - IL=15 mA Bypass Capacitor ESR 0.0 - 0.1 Bypass Capacitance 0.65 2.2 +35% F Notes 38. 39. 40. 41. 42. Excludes spread and tolerance due to board and 100 mOhm sense resistor tolerances. An additional derating of 35% is allowed. ADIN5, 6 and 7 inputs must not exceed BP voltage. TS[xy][1,2] inputs must not exceed BP or VCORE All characteristics in this table are applicable only for non touch screen operation. This applies to Touch Screen in Standalone mode and below. MC13892 24 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS DYNAMIC ELECTRICAL CHARACTERISTICS DYNAMIC ELECTRICAL CHARACTERISTICS Table 6. Dynamic Electrical Characteristics Characteristics noted under conditions 3.1 V BATT 4.65V, -40TA 85 C, GND = 0 V, unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25 C under nominal conditions, unless otherwise noted. Characteristic Symbol Min Typ Max Unit - - 1.0 - - - - 22 11 High Z 44 - - - - - 22 - 45 - 55 - - - - 11 6.0 High Z 22 - - - - - - 500 - - 2.0 - - - - 300 500 mV s - - - - 300 20 mV s 35 50 40 60 - - - - - -114 -124 -129 - - - - - 1.0 0.1 - 10 - 1.0 2.0 32 KHZ CRYSTAL OSCILLATOR RTC oscillator start-up time Upon application of power CLK32K Rise and Fall Time - CL = 50 pF CLK32KDRV[1:0] = 00 (default) CLK32KDRV[1:0] = 01 CLK32KDRV[1:0] = 10 CLK32KDRV[1:0] = 11 tRTCST tCLK32KET CLK32KMCU Rise and Fall Time CL = 12 pF tCLK32KMCUET CLK32K and CLK32KMCU Output Duty Cycle Crystal on XTAL1, XTAL2 pins tCLK32KDC, tCLK32KMCUDC Sec ns ns % CLK AND MISO MISO Rise and Fall Time, CL = 50 pF, SPIVCC = 1.8 V SPIDRV [1:0] = 00 (default) SPIDRV [1:0] = 01 SPIDRV [1:0] = 10 SPIDRV [1:0] = 11 tMISOET ns BUCK REGULATORS Turn-on Time, Enable to 90% of end value, IL = 0 tONPWM s SWBST Turn-on Time Enable to 90% of VOUT, IL = 0 tONBST Transient Load Response, IL from 1.0 mA to 100 mA in 1.0 s steps Maximum transient Amplitude Time to settle 80% of transient ATMAX Transient Load Response, IL from 100 mA to 1.0 mA Maximum transient Amplitude Time to settle 80% of transient ATMAX ms VVIDEO ACTIVE MODE - AC PSRR - IL = 75% of ILMAX, 20 Hz to 20 kHz VIN = VINMIN + 100 mV VIN = VNOM + 1.0 V Max Output Noise - VIN = VINMIN, IL = 75% of ILMAX 100 Hz - 1.0 kHz >1.0 kHz - 10 kHz >10 kHz - 1.0 MHz Turn-on Time Enable to 90% of end value, VIN = VINMIN, VINMAX, IL = 0 VVIDEOPSSR VVIDEOON VVIDEOtON dB dBV/Hz ms VVIDEO ACTIVE MODE - AC (CONTINUED) Turn-off Time Disable to 10% of initial value, VIN = VINMIN, VINMAX, IL = 0 VVIDEOtOFF Transient Load Response VIN = VINMIN, VINMAX VVIDEOTLOR ms % MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 25 ELECTRICAL CHARACTERISTICS DYNAMIC ELECTRICAL CHARACTERISTICS Table 6. Dynamic Electrical Characteristics (continued) Characteristics noted under conditions 3.1 V BATT 4.65V, -40TA 85 C, GND = 0 V, unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25 C under nominal conditions, unless otherwise noted. Characteristic Transient Line Response IL = 75% of ILMAX Mode Transition Time From low-power to active, VIN = VINMIN, VINMAX, IL = ILMAXLP Mode Transition Response From low-power to active and from active to low-power, VIN = VINMIN, VINMAX, IL = ILMAXLP Symbol VVIDEOTLIR VVIDEOtMOD VVIDEOMTR Min Typ Max - 5.0 8.0 - - 100 - 1.0 2.0 35 50 40 60 - - - - - -114 -124 -129 - - - - - 1.0 0.1 - 10 - 1.0 2.0 - 5.0 8.0 35 50 40 60 - - - - 20 2.5 - - - - 100 0.1 - 10 Unit mV s % VAUDIO PSRR - IL = 75% of ILMAX, 20 Hz to 20 kHz VIN = VINMIN + 100 mV, > UVDET VIN = VNOM + 1.0 V, > UVDET Max Output Noise - VIN = VINMIN, IL = 0.75*ILmax 100 Hz - 1.0 kHz >1.0 kHz - 10 kHz >10 kHz - 1.0 MHz VAUDIOPSSR VAUDIOON Turn-on Time Enable to 90% of end value, VIN = VINMIN, VINMAX, IL = 0 VAUDIOtON Turn-off Time Disable to 10% of initial value, VIN = VINMIN, VINMAX, IL = 0 VAUDIOtOFF Transient Load Response - See Transient Waveforms on page 84, VIN = VINMIN, VINMAX VAUDIOTLOR Transient Line Response - See Transient Waveforms on page 84 IL = 75% of ILMAX VAUDIOTLIR dB dBV/Hz ms ms % mV VPLL AND VDIG ACTIVE MODE - AC PSRR - IL = 75% of ILMAX, 20 Hz to 20 kHz VIN = UVDET VIN = VNOM + 1.0 V, > UVDET VPLLPSSR Output Noise - VIN = VINMIN, IL = 0.75*ILMAX 100 Hz - 1.0 kHz >1 kHz - 1.0 MHz VPLLON Turn-on Time Enable to 90% of end value, VIN = VINMIN, VINMAX, IL = 0 VPLLtON Turn-off Time Disable to 10% of initial value, VIN = VINMIN, VINMAX, IL = 0 VPLLtOFF Transient Load Response - See Transient Waveforms on page 84 VIN = VINMIN, VINMAX VPLLTLOR, VDIGTLOR - 50 70 Transient Line Response - See Transient Waveforms on page 84 IL = 75% of ILMAX VPLLTLIR, VDIGTLIR - 5.0 8.0 dB dB/dec V/Hz s ms mV mV MC13892 26 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS DYNAMIC ELECTRICAL CHARACTERISTICS Table 6. Dynamic Electrical Characteristics (continued) Characteristics noted under conditions 3.1 V BATT 4.65V, -40TA 85 C, GND = 0 V, unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25 C under nominal conditions, unless otherwise noted. Characteristic Symbol Min Typ Max Unit 35 50 40 60 - - - - 20 1.0 - - - - 1.0 0.1 - 10 - 1.0 2.0 - 5.0 8.0 - - 10 - 1.0 2.0 35 50 40 60 - - - - 20 1.0 - - dB/dec V/Hz VIOHI ACTIVE MODE - AC PSRR - IL = 75% of ILMAX, 20 Hz to 20 kHz VIN = VINMIN + 100 mV, > UVDET VIN = VNOM + 1.0 V, > UVDET VIOHIPSSR Output Noise - VIN = VINMIN, IL = 0.75*ILMAX 100 Hz - 1.0 kHz >1.0 kHz - 1.0 MHz VIOHION Turn-on Time Enable to 90% of end value, VIN = VINMIN, VINMAX, IL = 0 VIOHItON Turn-off Time Disable to 10% of initial value, VIN = VINMIN, VINMAX, IL = 0 VIOHItOFF Transient Load Response - See Transient Waveforms on page 84 VIN = VINMIN, VINMAX VIOHITLOR Transient Line Response - See Transient Waveforms on page 84 IL = 75% of ILMAX VIOHITLIR Mode Transition Time - See Transient Waveforms on page 84 From low-power to active, VIN = VINMIN, VINMAX, IL = ILMAXLP VIOHIMTR Mode Transition Response From low-power to active and from active to low-power, VIN = VINMIN, VINMAX, IL = ILMAXLP VIOHIMTR dB dB/dec V/Hz ms ms % mV s % VCAM ACTIVE MODE - AC PSRR - IL = 75% of ILMAX, 20 Hz to 20 kHz VIN = VINMIN + 100 mV VIN = VNOM + 1.0 V VCAMPSSR Output Noise - VIN = VINMIN, IL = 0.75*ILMAX 100 Hz - 1.0 kHz >1.0 kHz - 1.0 MHz VCAMON dB Turn-on Time (Enable to 90% of end value, VIN = VINMIN, VINMAX, IL = 0) VCAMtON - - 1.0 ms Turn-off Time (Disable to 10% of initial value, VIN = VINMIN, VINMAX, IL = 0) VCAMtOFF 0.1 - 10 ms - - 1.0 50 2.0 70 % mV - 5.0 8.0 - - 100 - 1.0 2.0 Transient Load Response - See Transient Waveforms on page 84 VIN = VINMIN, VINMAX VCAM = 01, 10, 11 VCAM = 00 VCAMLOR Transient Line Response - See Transient Waveforms on page 84 IL = 75% of ILMAX VCAMLIR Mode Transition Time - See Transient Waveforms on page 84 From low-power to active, VIN = VINMIN, VINMAX, IL = ILMAXLP VCAMtMOD Mode Transition Response From low-power to active and from, active to low-power, VIN = VINMIN, VINMAX, IL = ILMAXLP VCAMMTR mV s % MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 27 ELECTRICAL CHARACTERISTICS DYNAMIC ELECTRICAL CHARACTERISTICS Table 6. Dynamic Electrical Characteristics (continued) Characteristics noted under conditions 3.1 V BATT 4.65V, -40TA 85 C, GND = 0 V, unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25 C under nominal conditions, unless otherwise noted. Characteristic Symbol Min Typ Max 35 50 40 60 - - - - - -115 -126 -132 - - - Unit VSD ACTIVE MODE - AC PSRR - IL = 75% of ILMAX, 20 Hz to 20 kHz VIN = VINMIN + 100 mV VIN = VNOM + 1.0 V VSDPSSR dB Max Output Noise - VIN = VINMIN, IL = 75% of ILMAX 100 Hz - 1.0 kHz >1.0 kHz - 10 kHz >10 kHz - 1.0 MHz VSDON Turn-on Time (Enable to 90% of end value, VIN = VINMIN, VINMAX, IL = 0) VSDtON - - 1.0 ms Turn-off Time (Disable to 10% of initial value, VIN = VINMIN, VINMAX, IL = 0) VSDtOFF 0.1 - 10 ms Transient Load Response - See Transient Waveforms on page 84 VIN = VINMIN, VINMAX - VSD[2:0] = 010 to 111 - VSD[2:0] = 000 to 001 VSDTLOR - - 1.0 - 2.0 70 % mV Transient Line Response - See Transient Waveforms on page 84 IL = 75% of ILMAX VSDTLIR - 5.0 8.0 Mode Transition Time - See Transient Waveforms on page 84 From low-power to active, VIN = VINMIN, VINMAX, IL = ILMAXLP VSDtMOD - - 100 - 1.0 2.0 35 40 - - - 1.0 0.2 - - 35 50 40 60 - - - - 20 0.2 - - - - 100 0.1 - 10 - 1.0 2.0 - 1.0 2.0 - 5.0 8.0 Mode Transition Response - See Transient Waveforms on page 84 From low-power to active and from active to low-power, VIN = VINMIN, VINMAX, IL = ILMAXLP VSDMTR dBV/Hz mV s % VUSB ACTIVE MODE - AC PSRR - IL = 75% of ILMAX, 20 Hz to 20 kHz VIN = VINMIN + 100 mV Max Output Noise - VIN = VINMIN, IL = 75% of ILMAX 100 Hz - 50 kHz >50 kHz - 1.0 MHz VUSBPSSR VUSBON dB V/Hz VUSB2 ACTIVE MODE - AC PSRR - IL = 75% of ILMAX, 20 Hz to 20 kHz VIN = VINMIN + 100 mV VIN = VNOM + 1.0 V VUSB2PSSR Output Noise - VIN = VINMIN, IL = 0.75*ILMAX 100 Hz - 1.0 kHz >1.0 kHz - 1.0 MHz VUSB2ON Turn-on Time Enable to 90% of end value, VIN = VINMIN, VINMAX, IL = 0 VUSB2tON Turn-off Time Disable to 10% of initial value, VIN = VINMIN, VINMAX, IL = 0 VUSBtOFF Start-up Overshoot VIN = VINMIN, VINMAX, IL = 0 VUSB2OS Transient Load Response - See Transient Waveforms on page 84 VIN = VINMIN, VINMAX VUSB2TLOR Transient Line Response - See Transient Waveforms on page 84 IL = 75% of ILMAX VUSB2TLIR dB dB/dec V/Hz s ms % % mV MC13892 28 Analog Integrated Circuit Device Data Freescale Semiconductor ELECTRICAL CHARACTERISTICS DYNAMIC ELECTRICAL CHARACTERISTICS Table 6. Dynamic Electrical Characteristics (continued) Characteristics noted under conditions 3.1 V BATT 4.65V, -40TA 85 C, GND = 0 V, unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25 C under nominal conditions, unless otherwise noted. Characteristic Symbol Min Typ Max Unit - - 100 - - 1.3 35 50 40 60 - - - - - -115 -126 -132 - - - - - 1.0 0.1 - 10 - - 1.0 - 3.0 70 - 5.0 8.0 - - 100 - 1.0 2.0 35 50 40 60 - - - - - -115 -126 -132 - - - - - 1.0 0.1 - 10 ms - - 1.0 - 3.0 70 % mV - 5.0 8.0 UVBUS ACTIVE MODE DC Turn-on Time VBUS Rise Time per USB OTG with max loading of 6.5 F+10 F UVBUStON Turn-off Time UVBUStOFF Disable to 0.8 V, per USB OTG specification parameter VA_SESS_VLD, VIN = VINMIN, VINMAX, IL = 0 ms sec VGEN1 ACTIVE MODE - AC PSRR - IL = 75% of ILMAX, 20 Hz to 20 kHz VIN = UVDET VIN = VNOM + 1.0 V, > UVDET Max Output Noise - VIN = VINMIN, IL = 0.75*ILMAX 100 Hz - 1.0 kHz >1.0 kHz - 10 kHz >10 kHz - 1.0 MHz VGEN1PSSR VGEN1ON Turn-on Time Enable to 90% of end value VIN = VINMIN, VINMAX, IL = 0 VGEN1tON Turn-off Time Disable to 10% of initial value VIN = VINMIN, VINMAX, IL = 0 VGEN1tOFF Transient Load Response - See Transient Waveforms on page 84 VIN = VINMIN, VINMAX - VGEN1[1:0] = 10 to 11 - VGEN[1:0] = 00 to 01 VGEN1TLOR Transient Line Response - See Transient Waveforms on page 84 IL = 75% of ILMAX VGEN1TLIR Mode Transition Time - See Transient Waveforms on page 84 From low-power to active VIN = VINMIN, VINMAX, IL = ILMAXLP Mode Transition Response - See Transient Waveforms on page 84 From low-power to active and from active to low-power VIN = VINMIN, VINMAX, IL = ILMAXLP VGEN1tMOD VGEN1MTR dB dBV/Hz ms ms % mV mV s % VGEN2 ACTIVE MODE - AC PSRR - IL = 75% of ILMAX, 20 Hz to 20 kHz VIN = VINMIN + 100 mV VIN = VNOM + 1.0 V VGEN2PSSR Max Output Noise - VIN = VINMIN, IL = ILMAX 100 Hz - 1.0 kHz >1.0 kHz - 10 kHz >10 kHz - 1.0 MHz VGEN2ON Turn-on Time Enable to 90% of end value VIN = VINMIN, VINMAX, IL = 0 VGEN2tON Turn-off Time (Disable to 10% of initial value VIN = VINMIN, VINMAX, IL = 0) VGEN2tOFF Transient Load Response - See Transient Waveforms on page 84 VIN = VINMIN, VINMAX - VGEN2[2:0] = 100 to 111 - VGEN2[2:0] = 000 to 011 VGEN2TLOR Transient Line Response - See Transient Waveforms on page 84 IL = 75% of ILMAX VGEN2TLIR dB dBV/Hz ms mV MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 29 ELECTRICAL CHARACTERISTICS DYNAMIC ELECTRICAL CHARACTERISTICS Table 6. Dynamic Electrical Characteristics (continued) Characteristics noted under conditions 3.1 V BATT 4.65V, -40TA 85 C, GND = 0 V, unless otherwise noted. Typical values noted reflect the approximate parameter means at TA = 25 C under nominal conditions, unless otherwise noted. Characteristic Symbol Min Typ Max Unit - - 100 - 1.0 2.0 35 45 40 50 - - - - 20 1.0 - - - - 1.0 0.1 - 5.0 - - 1.0 - 2.0 70 % mV - 5.0 8.0 mV - - 100 - 1.0 2.0 Turn-on Time - VBUS Rise Time por USB OTG with max loading of 6.5 F+10 F - - 100 ms Turn-off Time - Disable to 0.8 V, per USB OTG specification parameter VA_SESS_VLD VIN = VINMIN, VINMAX, IL=0 - - 1.3 sec Conversion Time per Channel - PLLX[2:0] = 100 - - 10 s Turn On Delay If Switcher PLL was active If Switcher PLL was inactive - - 0.0 5.0 - 10 - - 500 VGEN2 ACTIVE MODE - AC (CONTINUED) Mode Transition Time - See Transient Waveforms on page 84 From low-power to active VIN = VINMIN, VINMAX, IL = ILMAXLP Mode Transition Response - See Transient Waveforms on page 84 From low-power to active and from active to low-power VIN = VINMIN, VINMAX, IL = ILMAXLP VGEN2tMOD VGEN2MTR s % VGEN3 ACTIVE MODE - AC PSRR IL = 75% of ILMAX, 20 Hz to 20 kHz, VIN = VINMIN +100 mV VIN = VNOM+1.0 V Output Noise - VIN = VINMIN, IL = 75% of ILMAX 100 Hz - 1.0 kHz >1.0 kHz - 1.0 MHz VGEN3PSSR VGEN3ON Turn-on Time Enable to 90% of end value VIN = VINMIN, VINMAX, IL = 0 VGEN3tON Turn-off Time Disable to 10% of initial value VIN = VINMIN, VINMAX, IL = 0 VGEN3tOFF Transient Load Response VIN = VINMIN, VINMAX - VGEN3 = 1 - VGEN3 = 0 VGEN3TLOR Transient Line Response (IL = 75% of ILMAX) VGEN3TLIR Mode Transition Time From low-power to active VIN = VINMIN, VINMAX, IL = ILMAXLP Mode Transition Response From low-power to active and from active to low-power, VIN = VINMIN, VINMAX, IL = ILMAXLP VGEN3tMOD VGEN3MTR dB dB/dec V/Hz ms ms s % UVBUS - ACTIVE MODE DC ADC s TOUCH SCREEN Turn-on Time - 90% of output s MC13892 30 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DESCRIPTION FUNCTIONAL PIN DESCRIPTION FUNCTIONAL DESCRIPTION FUNCTIONAL PIN DESCRIPTION CHARGER CHRGRAW 1. Charger input. The charger voltage is measured through an ADC at this pin. The UVBUS pin must be shorted to CHRGRAW in cases where the charger is being supplied from the USB cable. The minimum voltage for this pin depends on BATTMIN threshold value (see Battery Interface and Control). 2. Output to battery supplied accessories. The battery voltage can be applied to an accessory by enabling the charge path for the accessory via the CHRGRAW pin. To accomplish this, the charger needs to be configured in reverse supply mode. CHRGCTRL1 Driver output for charger path FET M1. CHRGCTRL2 Driver output for charger path FET M2. CHRGISNS Charge current sensing point 1. The charge current is read by monitoring the voltage drop over the charge current 100 m sense resistor connected between CHRGISNS and BPSNS. BPSNS 1. BP sense point. BP voltage is sensed at this pin and compared with the voltage at CHRGRAW. 2. Charge current sensing point 2. The charge current is read by monitoring the voltage drop over the charge current 100 m sense resistor. This resistor is connected between CHRGISNS and BPSNS. BP This pin is the application supply point, the input supply to the IC core circuitry. The application supply voltage is sensed through an ADC at this pin. BATTFET Driver output for battery path FET M3. If no charging system is required or single path is implemented, the pin BATTFET must be floating. BATTISNS Battery current sensing point 1. The current flowing out of and into the battery can be read via the ADC by monitoring the voltage drop over the sense resistor between BATT and BATTISNS. BATT Battery positive terminal. Battery current sensing point 2. The supply voltage of the battery is sensed through an ADC on this pin. The current flowing out of and into the battery can be read via the ADC by monitoring the voltage drop over the sense resistor between BATT and BATTISNS. BATTISNSCC Accumulated current counter current sensing point. This is the coulomb counter current sense point. It should be connected directly to the 0.020 sense resistor via a separate route from BATTISNS. The coulomb counter monitors the current flowing in/ out of the battery by integrating the voltage drop over the BATTISNCC and the BATT pin. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 31 FUNCTIONAL DESCRIPTION FUNCTIONAL PIN DESCRIPTION CFP AND CFM Accumulated current filter cap plus and minus pins respectively. The coulomb counter will require a 10 F output capacitor connected between these pins to perform a first order filtering of the signal across R1. CHRGSE1B An unregulated wall charger configuration can be built in which case this pin must be pulled low. When charging through USB, it can be left open since it is internally pulled up to VCORE. The recommendation is to place an external FET that can pull it low or left it open, depending on the charge method. CHRGLED Trickle LED driver output 1. Since normal LED control via the SPI bus is not always possible in the standalone operation, a current sink is provided at the CHRGLED pin. This LED is to be connected between this pin and CHRGRAW. GNDCHRG Ground for charger interface. LEDR, LEDG AND LEDB General purpose LED driver output Red, Green and Blue respectively. Each channel provides flexible LED intensity control. These pins can also be used as general purpose open drain outputs for logic signaling, or as generic PWM generator outputs. GNDLED Ground for LED drivers IC CORE VCORE Regulated supply output for the IC analog core circuitry. It is used to define the PUMS VIH level during initialization. The bandgap and the rest of the core circuitry are supplied from VCORE. Place a 2.2 F capacitor from this pin to GNDCORE. VCOREDIG Regulated supply output for the IC digital core circuitry. No external DC loading is allowed on VCOREDIG. VCOREDIG is kept powered as long as there is a valid supply and/or coin cell. Place a 2.2 F capacitor from this pin to GNDCORE. REFCORE Main bandgap reference. All regulators use the main bandgap as the reference. The main bandgap is bypassed with a capacitor at REFCORE. No external DC loading is allowed on REFCORE. Place a 100 nF capacitor from this pin to GNDCORE. GNDCORE Ground for the IC core circuitry. POWER GATING PWGTDRV1 AND PWGTDRV2 Power Gate Drivers. PWGTDRV1 is provided for power gating peripheral loads sharing the processor core supply domain(s) SW1, and/or SW2, and/or SW3. In addition, PWGTDRV2 provides support to power gate peripheral loads on the SW4 supply domain. In typical applications, SW1, SW2, and SW3 will both be kept active for the processor modules in state retention, and SW4 retained for the external memory in self refresh mode. SW1, SW2, and SW3 power gating FET drive would typically be connected to PWGTDRV1 (for parallel NMOS switches). SW4 power gating FET drive would typically be connected to PWGTDRV2. When Low-power Off mode is activated, the power gate drive circuitry will be disabled, turning off the NMOS power gate switches to isolate the maintained supply domains from any peripheral loading. MC13892 32 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DESCRIPTION FUNCTIONAL PIN DESCRIPTION SWITCHERS SW1IN, SW2IN, SW3IN AND SW4IN Switchers 1, 2, 3, and 4 input. Connect these pins to BP to supply Switchers 1, 2, 3, and 4. SW1FB, SW2FB, SW3FB AND SW4FB Switchers 1, 2, 3, and 4 feedback. Switchers 1, 2, 3, and 4 output voltage sense respectively. Connect these pins to the farther point of each of their respective SWxOUT pin, in order to sense and maintain voltage stability. SW1OUT Switcher 1 output. Buck regulator for processor core(s). GNDSW1 Ground for Switcher 1. SW2OUT Switcher 2 output. Buck regulator for processor SOG, etc. GNDSW2 Ground for Switcher 2. SW3OUT Switcher 3 output. Buck regulator for internal processor memory and peripherals. GNDSW3 Ground for switcher 3. SW4OUT Switcher 4 output. Buck regulator for external memory and peripherals. GNDSW4 Ground for switcher 4. DVS1 AND DVS2 Switcher 1 and 2 DVS input pins. Provided for pin controlled DVS on the buck regulators targeted for processor core supplies. The DVS pins may be reconfigured for Switcher Increment / Decrement (SID) mode control. When transitioning from one voltage to another, the output voltage slope is controlled in steps of 25 mV per time step. These pins must be set high in order for the DVS feature to be enabled for each of switchers 1 or 2, or low to disable it. SWBSTIN Switcher BST input. The 2.2 H switcher BST inductor must be connected here. SWBSTOUT Power supply for gate driver for the internal power NMOS that charges SWBST inductor. It must be connected to BP. SWBSTFB Switcher BST feedback. When SWBST is configured to supply the UVBUS pin in OTG mode the feedback will be switched to sense the UVBUS pin instead of the SWBSTFB pin. GNDSWBST Ground for switcher BST. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 33 FUNCTIONAL DESCRIPTION FUNCTIONAL PIN DESCRIPTION REGULATORS VINIOHI Input of VIOHI regulator. Connect this pin to BP in order to supply VIOHI regulator. VIOHI Output regulator for high voltage IO. Fixed 2.775 V output for high-voltage level interface. VINPLL AND VINDIG The input of the regulator for processor PLL and Digital regulators respectively. VINDIG and VINPLL can be connected to either BP or a 1.8 V switched mode power supply rail, such as from SW4 for the two lower set points of each regulator (the 1.2 and 1.25 V output for VPLL, and 1.05 and 1.25 V output for VDIG). In addition, when the two upper set points are used (1.50 and 1.8 V outputs for VPLL, and 1.65 and 1.8 V for VDIG), they can be connected to either BP or a 2.2 V nominal external switched mode power supply rail, to improve power dissipation. VPLL Output of regulator for processor PLL. Quiet analog supply (PLL, GPS). VDIG Output regulator Digital. Low voltage digital (DPLL, GPS). VVIDEODRV Drive output for VVIDEO external PNP transistor. VVIDEO Output regulator TV DAC. This pin must be connected to the collector of the external PNP transistor of the VVIDEO regulator. VINAUDIO Input regulator VAUDIO. Typically connected to BP. VAUDIO Output regulator for audio supply. VINUSB2 Input regulator VUSB2. This pin must always be connected to BP even if the regulators are not used by the application. VUSB2 Output regulator for powering USB PHY. VINCAMDRV 1. Input regulator camera using internal PMOS FET. Typically connected to BP. 2. Drive output regulator for camera voltage using external PNP device. In this case, this pin must be connected to the base of the PNP in order to drive it. VCAM Output regulator for the camera module. When using an external PNP device, this pin must be connected to its collector. VSDDRV Drive output for the VSD external PNP transistor. VSD Output regulator for multi-media cards such as micro SD, RS-MMC. MC13892 34 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DESCRIPTION FUNCTIONAL PIN DESCRIPTION VGEN1DRV Drive output for the VGEN1 external PNP transistor. VGEN1 Output of general purpose 1 regulator. VGEN2DRV Drive output for the VGEN2 external PNP transistor. VGEN2 Output of general purpose 2 regulator. VINGEN3DRV 1. Input for the VGEN3 regulator when no external PNP transistor used. Typically connected to BP. 2. Drive output for VGEN3 in case an external PNP transistor is used on the application. In this case, this pin must be connected the base of the PNP transistor. VGEN3 Output of general purpose 3 regulator. VSRTC Output regulator for the SRTC module on the processor. The VSRTC regulator provides the CLK32KMCU output level (1.2 V). Additionally, it is used to bias the low-power SRTC domain of the SRTC module integrated on certain FSL processors. GNDREG1 Ground for regulators 1. GNDREG2 Ground for regulators 2. GNDREG3 Ground for regulators 3. GENERAL OUTPUTS GPO1 General purpose output 1. Intended to be used for battery thermistor biasing. In this case, connect a 10 K resistor from GPO1 to ADIN5, and one from ADIN5 to GND. GPO2 General purpose output 2. GPO3 General purpose output 3. GPO4 General purpose output 4. It can be configured for a muxed connection into Channel 7 of the GP ADC. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 35 FUNCTIONAL DESCRIPTION FUNCTIONAL PIN DESCRIPTION CONTROL LOGIC LICELL Coin cell supply input and charger output. The LICELL pin provides a connection for a coin cell backup battery or supercap. If the main battery is deeply discharged, removed, or contact-bounced (i.e., during a power cut), the RTC system and coin cell maintained logic will switch over to the LICELL for backup power. This pin also works as a current-limited voltage source for battery charging. A small capacitor should be placed from LICELL to ground under all circumstances. XTAL1 32.768 kHz Oscillator crystal connection 1. XTAL2 32.768 kHz Oscillator crystal connection 2. GNDRTC Ground for the RTC block. CLK32K 32 kHz Clock output for peripherals. At system start-up, the 32 kHz clock is driven to CLK32K (provided as a peripheral clock reference), which is referenced to SPIVCC. The CLK32K is restricted to state machine activation in normal on mode. CLK32KMCU 32 kHz Clock output for processor. At system start-up, the 32 kHz clock is driven to CLK32KMCU (intended as the CKIL input to the system processor) referenced to VSRTC. The driver is enabled by the start-up sequencer and the CLK32KMCU is programmable for Low-power Off mode control by the state machine. RESETB AND RESETBMCU Reset output for peripherals and processor respectively. These depend on the Power Control Modes of operation (See Functional Device Operation on page 40). These are meant as reset for the processor, or peripherals in a power up condition, or to keep one in reset while the other is up and running. WDI Watchdog input. This pin must be high to stay in the On mode. The WDI IO supply voltage is referenced to SPIVCC (normally connected to SW4 = 1.8 V). SPIVCC must therefore remain enabled to allow for proper WDI detection. If WDI goes low, the system will transition to the Off state or Cold Start (depending on the configuration). STANDBY AND STANDBYSEC Standby input signal from processor and from peripherals respectively. To ensure that shared resources are properly powered when required, the system will only be allowed into Standby when both the application processor (which typically controls the STANDBY pin) and peripherals (which typically control the STANDBYSEC pin) allow it. This is referred to as a Standby event. The Standby pins are programmable for Active High or Active Low polarity, and that decoding of a Standby event will take into account the programmed input polarities associated with each pin. Since the Standby pin activity is driven asynchronously to the system, a finite time is required for the internal logic to qualify and respond to the pin level changes. The state of the Standby pins only have influence in the On mode and are therefore ignored during start up and in the Watchdog phase. This allows the system to power up without concern of the required Standby polarities, since software can make adjustments accordingly, as soon as it is running. INT Interrupt to processor. Unmasked interrupt events are signaled to the processor by driving the INT pin high. MC13892 36 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DESCRIPTION FUNCTIONAL PIN DESCRIPTION PWRON1, 2 AND 3 A turn on event can be accomplished by connecting an open drain NMOS driver to the PWRONx pin of the MC13892, so that it is in effect a parallel path for the power key. In addition to the turn on event, the MC13892A/B/C/D versions include a global reset feature on the PWRON3 pin. On the A/B/C/D versions, the GLBRSTENB defaults to 0. In the MC13892A/C versions global reset is active low. Since GLBRSTENB defaults to 0, the global reset feature is enabled by default. In the MC13892B/D versions global reset is active high. Since GLBRSTENB defaults to 0, the global reset feature is disabled by default. The global reset function can be enabled or disabled by changing the SPI bit GLBRSTENB at any time, as shown in table below: Device Global Reset Function GLBRSTENB Configuration GLBRSTENB MC13892 NO N/A N/A MC13892A YES Active low 0 = Enabled (default) 1 = Disabled MC13892B YES Active HI 0 = Disabled (default) 1 = Enabled MC13892C YES Active low 0 = Enabled (default) 1 = Disabled MC13892D YES Active HI 0 = Disabled (default) 1 = Enabled The global reset feature powers down the part, disables the charger, resets the SPI registers to their default value and then powers back on. To generate a global reset, the PWRON3 pin needs to be pulled low for greater than 12 seconds and then pulled back high. If the PWRON3 pin is held low for less than 12 seconds, the pin will act as a normal PWRON pin. PUMS1 AND PUMS2 Power up mode supply setting. Default start-up of the device is selectable by hardwiring the Power Up Mode Select pins. The Power Up Mode Select pins (PUMS1 and PUMS2) are used to configure the start-up characteristics of the regulators. Supply enabling and output level options are selected by hardworking the PUMS pins for the desired configuration. MODE USB LBP mode, normal mode, test mode selection & anti-fuse bias. During evaluation and testing, the IC can be configured for normal operation or test mode via the MODE pin as summarized in the following table. MODE PIN STATE MODE Ground Normal Operation VCOREDIG USB Low-power Boot Allowed VCORE Test Mode GNDCTRL Ground for control logic. SPIVCC Supply for SPI bus and audio bus CS CS held low at Cold Start configures the interface for SPI mode. Once activated, CS functions as the SPI Chip Select. CS tied to VCORE at Cold Start configures the interface for I2C mode; the pin is not used in I2C mode other than for configuration. Because the SPI interface pins can be reconfigured for reuse as an I2C interface, a configuration protocol mandates that the CS pin is held low during a turn on event for the IC (a weak pull-down is integrated on the CS pin). MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 37 FUNCTIONAL DESCRIPTION FUNCTIONAL PIN DESCRIPTION CLK Primary SPI clock input. In I2C mode, this pin is the SCL signal (I2C bus clock). MOSI Primary SPI write input. In I2C mode, the MOSI pin hard wired to ground or VCORE is used to select between two possible addresses (A0 address selection). MISO Primary SPI read output. In I2C mode, this pin is the SDA signal (bi-directional serial data line). GNDSPI Ground for SPI interface. USB UID This pin identifies if a mini-A or mini-B style plug has been connected to the application. The state of the ID detection can be read via the SPI, to poll dedicated sense bits for a floating, grounded, or factory mode condition on the UID pin. UVBUS 1. USB transceiver cable interface. 2. OTG supply output. When SWBST is configured to supply the UVBUS pin in OTG mode, the feedback will switch to sense the UVBUS pin instead of the SWBSTFB pin. VUSB This is the regulator used to provide a voltage to an external USB transceiver IC. VINUSB Input option for VUSB; supplied by SWBST. This pin is internally connected to the UVBUS pin for OTG mode operation (for more details about OTG mode). Note: When VUSBIN = 1, UVBUS will be connected via internal switches to VINUSB and incur some current drain on that pin, as much as 270 A maximum, so care must be taken to disable this path and set this SPI bit (VUSBIN) to 0 to minimize current drain, even if SWBST and/or VUSB are disabled. VBUSEN External VBUS enable pin for the OTG supply. VBUS is defined as the power rail of the USB cable (+5.0 V). A TO D CONVERTER Note: The ADIN5/6/7 inputs must not exceed BP. ADIN5 ADC generic input channel 5. ADIN5 may be used as a general purpose unscaled input, but in a typical application, ADIN5 is used to read out the battery pack thermistor. The thermistor must be biased with an external pull-up to a voltage rail greater than the ADC input range. In order to save current when the thermistor reading is not required, it can be biased from one of the general purpose IOs such as GPO1. A resistor divider network should assure the resulting voltage falls within the ADC input range, in particular when the thermistor check function is used. ADIN6 ADC generic input channel 6. ADIN6 may be used as a general purpose unscaled input, but in a typical application, the PA thermistor is connected here. MC13892 38 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DESCRIPTION FUNCTIONAL PIN DESCRIPTION ADIN7 ADC generic input channel 7, group 1. ADIN7 may be used as a general purpose unscaled input or as a divide by 2 scaled input. In a typical application, an ambient light sensor is connected here. A second general purpose input ADIN7B is available on channel 7. This input is muxed on the GPO4 pin. In the application, a second ambient light sensor is supposed to be connected here. TSX1 AND TSX2, TSY1 AND TSY2 - Note: The TS[xy] [12] inputs must not exceed BP or VCORE. Touch Screen Interfaces X1 and X2, Y1 and Y2. The touch screen X plate is connected to TSX1 and TSX2, while the Y plate is connected to Y1 and Y2. In inactive mode, these pins can also be used as general purpose ADC inputs. They are respectively mapped on ADC channels 4, 5, 6, and 7. In interrupt mode, a voltage is applied to the X-plate (TSX2) via a weak current source to VCORE, while the Y-plate is connected to ground (TSY1). TSREF Touch Screen Reference regulator. This regulator is powered from VCORE. In applications not supporting touch screen, the TSREF can be used as a low current general purpose regulator, or it can be kept disabled and the bypass capacitor omitted. ADTRIG ADC trigger input. A rising edge on this pin will start an ADC conversion. GNDADC Ground for A to D circuitry. THERMAL GROUNDS GNDSUB1-9 General grounds and thermal heat sinks. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 39 FUNCTIONAL DEVICE OPERATION PROGRAMMABILITY FUNCTIONAL DEVICE OPERATION PROGRAMMABILITY INTERFACING OVERVIEW AND CONFIGURATION OPTIONS The MC13892 contains a number of programmable registers for control and communication. The majority of registers are accessed through a SPI interface in a typical application. The same register set may alternatively be accessed with an I2C interface that is muxed on SPI pins. The following table describes the muxed pin options for the SPI and I2C interfaces. Further details for each interface mode follow in this chapter. Table 7. SPI / I2C Bus Configuration Pin Name SPI Mode Functionality (43) I2C Mode Functionality Configuration (44) CS Configuration , Chip Select CLK SPI Clock SCL: I2C bus clock MISO Master In, Slave Out (data output) SDA: Bi-directional serial data line MOSI Master Out, Slave In (data input) A0 Address Selection (45) Notes 43. CS held low at Cold Start configures interface for SPI mode; once activated, CS functions as the SPI Chip Select. 44. CS tied to VCORE at Cold Start configures interface for I2C mode; the pin is not used in I2C mode other than for configuration. 45. In I2C mode, the MOSI pin hard wired to ground or VCORE is used to select between two possible addresses. SPI INTERFACE The MC13892 contains a SPI interface port, which allows access by a processor to the register set. Via these registers, the resources of the IC can be controlled. The registers also provide status information about how the IC is operating, as well as information on external signals. The SPI interface pins can be reconfigured for reuse as an I2C interface. As a result, a configuration protocol mandates that the CS pin is held low during a turn on event for the IC (a weak pull-down is integrated on the CS pin. With the CS pin held low during startup (as would be the case if connected to the CS driver of an unpowered processor, due to the integrated pull-down), the bus configuration will be latched for SPI mode. The SPI port utilizes 32-bit serial data words comprised of 1 write/read_b bit, 6 address bits, 1 null bit, and 24 data bits. The addressable register map spans 64 registers of 24 data bits each. The general structure of the register set is given in the following table. Bit names, positions, and basic descriptions are provided in SPI Bitmap. Expanded bit descriptions are included in the following functional chapters for application guidance. For brevity's sake, references are occasionally made herein to the register set as the "SPI map" or "SPI bits", but note that bit access is also possible through the I2C interface option, so such references are implied as generically applicable to the register set accessible by either interface. Table 8. Register Set Register Register Register Register 0 Interrupt Status 0 16 Unused 32 Regulator Mode 0 48 Charger 0 1 Interrupt Mask 0 17 Unused 33 Regulator Mode 1 49 USB0 2 Interrupt Sense 0 18 Memory A 34 Power Miscellaneous 50 Charger USB1 3 Interrupt Status 1 19 Memory B 35 Unused 51 LED Control 0 4 Interrupt Mask 1 20 RTC Time 36 Unused 52 LED Control 1 5 Interrupt Sense 1 21 RTC Alarm 37 Unused 53 LED Control 2 6 Power Up Mode Sense 22 RTC Day 38 Unused 54 LED Control 3 7 Identification 23 RTC Day Alarm 39 Unused 55 Unused 8 Unused 24 Switchers 0 40 Unused 56 Unused 9 ACC 0 25 Switchers 1 41 Unused 57 Trim 0 10 ACC 1 26 Switchers 2 42 Unused 58 Trim 1 11 Unused 27 Switchers 3 43 ADC 0 59 Test 0 MC13892 40 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION PROGRAMMABILITY Table 8. Register Set Register Register Register Register 12 Unused 28 Switchers 4 44 ADC 1 60 Test 1 13 Power Control 0 29 Switchers 5 45 ADC 2 61 Test 2 14 Power Control 1 30 Regulator Setting 0 46 ADC 3 62 Test 3 15 Power Control 2 31 Regulator Setting 1 47 ADC4 63 Test 4 The SPI interface is comprised of the package pins listed in Table 9. Table 9. SPI Interface Pin Description SPI Bus Description CLK Clock input line, data shifting occurs at the rising edge MOSI Serial data input line MISO Serial data output line CS Clock enable line, active high Interrupt INT Description Interrupt to processor Supply SPIVCC Description Processor SPI bus supply SPI INTERFACE DESCRIPTION The control bits are organized into 64 fields. Each of these 64 fields contains 32-bits. A maximum of 24 data bits are used per field. In addition, there is one "dead" bit between the data and address fields. The remaining bits include 6 address bits to address the 64 data fields and one write enable bit to select whether the SPI transaction is a read or a write. The register set will be to a large extent compatible with the MC13783, in order to facilitate software development. For each SPI transfer, first a one is written to the read/write bit if this SPI transfer is to be a write. A zero is written to the read/ write bit if this is to be a read command only. The CS line must remain high during the entire SPI transfer. To start a new SPI transfer, the CS line must go inactive and then go active again. The MISO line will be tri-stated while CS is low. To read a field of data, the MISO pin will output the data field pointed to by the 6 address bits loaded at the beginning of the SPI sequence. Figure 5. SPI Transfer Protocol Single Read/Write Access MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 41 FUNCTIONAL DEVICE OPERATION PROGRAMMABILITY Figure 6. SPI Transfer Protocol Multiple Read/Write Access SPI ELECTRICAL & TIMING REQUIREMENTS The following diagram and table summarize the SPI electrical and timing requirements. The SPI input and output levels are set independently via the SPIVCC pin by connecting it to the desired supply. This would typically be tied to SW4 programmed for 1.80 V. The strength of the MISO driver is programmable through the SPIDRV[1:0] bits. Figure 7. SPI Interface Timing Diagram MC13892 42 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION PROGRAMMABILITY Table 10. SPI Interface Timing Specifications Parameter Description t min (ns) tSELSU Time CS has to be high before the first rising edge of CLK 15 tSELHLD Time CS has to remain high after the last falling edge of CLK 15 tSELLOW Time CS has to remain low between two transfers 15 tCLKPER Clock period of CLK 38 tCLKHIGH Part of the clock period where CLK has to remain high 15 tCLKLOW Part of the clock period where CLK has to remain low 15 tWRTSU Time MOSI has to be stable before the next rising edge of CLK 4.0 tWRTHLD Time MOSI has to remain stable after the rising edge of CLK 4.0 tRDSU Time MISO will be stable before the next rising edge of CLK 4.0 tRDHLD Time MISO will remain stable after the falling edge of CLK 4.0 tRDEN Time MISO needs to become active after the rising edge of CS 4.0 tRDDIS Time MISO needs to become inactive after the falling edge of CS 4.0 Notes 46. This table reflects a maximum SPI clock frequency of 26 MHz Table 11. SPI Interface Logic IO Specifications Parameter Condition Min Typ Max Units Input Low CS, MOSI, CLK 0.0 - 0.3*SPIVCC V Input High CS, MOSI, CLK 0.7*SPIVCC - SPIVCC+0.3 V 0 - 0.2 V SPIVCC-0.2 - SPIVCC V 1.75 - 3.1 V SPIDRV[1:0] = 00 (default) - 11 - ns SPIDRV[1:0] = 01 - 6.0 - ns SPIDRV[1:0] = 10 - High Z - ns SPIDRV[1:0] = 11 - 22 - ns Output Low MISO, INT Output sink 100 A Output High MISO, INT Output source 100 A SPIVCC Operating Range CL = 50 pF, SPIVCC = 1.8 V MISO Rise and Fall Time MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 43 FUNCTIONAL DEVICE OPERATION I2C INTERFACE I2C INTERFACE I2C CONFIGURATION When configured for I2C mode (see Table 7) the interface may be used to access the complete register map previously described for SPI access. The MC13892 can function only as an I2C slave device, not as a host. I2C interface protocol requires a device ID for addressing the target IC on a multi-device bus. To allow flexibility in addressing for bus conflict avoidance, pin programmable selection is provided through the MOSI pin to allow configuration for the address LSB(s). This product supports 7-bit addressing only; support is not provided for 10-bit or General Call addressing. The I2C mode of the interface is implemented generally following the Fast Mode definition which supports up to 400 kbits/s operation. Timing diagrams, electrical specifications, and further details can be found in the I2C specification. Standard I2C protocol utilizes packets of 8-bits (bytes), with an acknowledge bit (ACK) required between each byte. However, the number of bytes per transfer is unrestricted. The register map of the MC13892 is organized in 24-bit registers which corresponds to the 24-bit words supported by the SPI protocol of this product. To ensure that the I2C operation mimics SPI transactions in behavior of a complete 24-bit word being written in one transaction, software is expected to perform write transactions to the device in 3 byte sequences, beginning with the MSB. Internally, data latching will be gated by the acknowledge at the completion of writing the third consecutive byte. Failure to complete a 3 byte write sequence will abort the I2C transaction and the register will retain its previous value. This could be due to a premature STOP command from the master. I2C read operations are also performed in byte increments separated by an ACK. Read operations also begin with the MSB and 3 bytes will be sent out, unless a STOP command or NACK is received prior to completion. The following examples show how to write and read data to the IC. The host initiates and terminates all communication. The host sends a master command packet after driving the start condition. The device will respond to the host if the master command packet contains the corresponding slave address. In the following examples, the device is shown always responding with an ACK to transmissions from the host. If at any time a NAK is received, the host should terminate the current transaction and retry the transaction. I2C DEVICE ID The I2C interface protocol requires a device ID for addressing the target IC on a multi-device bus. To allow flexibility in addressing for bus conflict avoidance, pin programmable selection is provided to allow configuration for the address LSB(s). This product supports 7-bit addressing only. Support is not provided for 10-bit or General Call addressing. Because the MOSI pin is not utilized for I2C communication, it is reassigned for pin programmable address selection by hardwiring to VCORE or GND at the board level, when configured for I2C mode. MOSI will act as Bit 0 of the address. The I2C address assigned to FSL PM ICs (shared amongst our portfolio) is as follows: 00010-A1-A0, where the A1 and A0 bits are allowed to be configured for either 1 or 0. It is anticipated for a maximum of two FSL PM ICs on a given board, which could be sharing an I2C bus. The A1 address bit is internally hard wired as a "0", leaving the LSB A0 for board level configuration. The A1 bit will be implemented such that it can be re-wired as a "1" (with a metal change or fuse trim), if conflicts are encountered before the final production material is manufactured. The designated address is defined as: 000100-A0. I2C OPERATION The I2C mode of the interface is implemented, generally following the Fast mode definition, which supports up to 400 kbits/s operation. The exceptions to the standard are noted to be 7-bit only addressing, and no support for General Call addressing. Timing diagrams, electrical specifications, and further details can be found in the I2C specification, which is available for download at: http://www.nxp.com/acrobat_download/literature/9398/39340011.pdf Standard I2C protocol utilizes bytes of 8-bits, with an acknowledge bit (ACK) required between each byte. However, the number of bytes per transfer are unrestricted. The register map is organized in 24-bit registers, which corresponds to the 24-bit words supported by the SPI protocol of this product. To ensure that I2C operation mimics SPI transactions in behavior of a complete 24-bit word being written in one transaction. The software is expected to perform write transactions to the device in 3 byte sequences, beginning with the MSB. Internally, data latching will be gated by the acknowledge at the completion of writing the third consecutive byte. Failure to complete a 3 byte write sequence will abort the I2C transaction, and the register will retain its previous value. This could be due to a premature STOP command from the master, for example. I2C read operations are also performed in byte MC13892 44 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION I2C INTERFACE increments separated by an ACK. Read operations also begin with the MSB, and 3 bytes will be sent out unless a STOP command or NACK is received prior to completion. The following examples show how to write and read data to the IC. The host initiates and terminates all communication. The host sends a master command packet after driving the start condition. The device will respond to the host if the master command packet contains the corresponding slave address. In the following examples, the device is shown always responding with an ACK to transmissions from the host. If at any time a NAK is received, the host should terminate the current transaction and retry the transaction. Figure 8. I2C 3 Byte Write Example Figure 9. I2C 3 Byte Read Example MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 45 FUNCTIONAL DEVICE OPERATION I2C INTERFACE INTERRUPT HANDLING CONTROL The MC13892 has interrupt generation capability to inform the system on important events occurring. An interrupt is signaled to the processor by driving the INT pin high. This is true whether the communication interface is configured for the SPI or I2C. Each interrupt is latched so that even if the interrupt source becomes inactive, the interrupt will remain set until cleared. Each interrupt can be cleared by writing a 1 to the appropriate bit in the Interrupt Status register. This will also cause the interrupt line to go low. If a new interrupt occurs while the processor clears an existing interrupt bit, the interrupt line will remain high. Each interrupt can be masked by setting the corresponding mask bit to a 1. As a result, when a masked interrupt bit goes high, the interrupt line will not go high. A masked interrupt can still be read from the Interrupt Status register. This gives the processor the option of polling for status from the IC. The IC powers up with all interrupts masked except the USB low-power boot, so the processor must initially poll the device to determine if any interrupts are active. Alternatively, the processor can unmask the interrupt bits of interest. If a masked interrupt bit was already high, the interrupt line will go high after unmasking. The sense registers contain status and input sense bits so the system processor can poll the current state of interrupt sources. They are read only, and not latched or clearable. Interrupts generated by external events are debounced, meaning that the event needs to be stable throughout the debounce period before an interrupt is generated. BIT SUMMARY Table 12 summarizes all interrupt, mask, and sense bits associated with INT control. For more detailed behavioral descriptions, refer to the related chapters. Table 12. Interrupt, Mask and Sense Bits Interrupt Mask Sense Trigger DebounceTi me Purpose Section ADCDONEI ADCDONEM - ADC has finished requested conversions L2H 0 page 100 ADCBISDONEI ADCBISDONEM - ADCBIS has finished requested conversions L2H 0 page 100 TSI TSM - Touch screen wake-up Dual 30ms page 100 CHGDETS Charger detection sense is 1 if detected Charger state sense is 1 if active Dual CHGDETI CHGDETM CHGENS 32 ms page 89 100 ms USBOVI USBOVM USBOVS VBUS over-voltage Sense is 1 if above threshold Dual 60 s page 89 CHGREVI CHGREVM - Charger path reverse current L2H 1.0 ms page 89 CHGSHORTI CHGSHORTM - Charger path short circuit L2H 1.0 ms page 89 L2H 10 ms page 89 CHGFAULTI CHGFAULTM CHGFAULTS[1:0] Charger fault detection 00 = Cleared, no fault 01 = Charge source fault 10 = Battery fault 11 = Battery temperature CHGCURRI CHGCURRM CHGCURRS Charge current below threshold Sense is 1 if above threshold H2L 1.0 ms page 89 CCCVI CCCVM CCCVS CCCVI transition detection Dual 100 ms page 89 L2H 30 ms page 54 L2H 0 page 54 Dual L2H: 2024 ms H2L: 812 ms page 111 BPONI BPONM BPONS BP turn on threshold detection. Sense is 1 if above threshold. LOBATLI LOBATLM LOBATLS Low battery detect Sense is 1 if below LOBATL threshold USB B-session valid BVALIDI BVALIDM BVALIDS Sense is 1 if above threshold MC13892 46 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION I2C INTERFACE Table 12. Interrupt, Mask and Sense Bits Interrupt LOBATHI Mask LOBATHM Sense LOBATHS Purpose Low battery warning Sense is 1 if above LOBATH threshold. Trigger DebounceTi me Section Dual 30 s page 54 page 111 VBUSVALIDI VBUSVALIDM VBUSVALIDS Detects A-Session Valid on VBUS Dual L2H: 2024 ms H2L: 812 ms IDFLOATI IDFLOATM IDFLOATS ID floating detect. Sense is 1 if above threshold Dual 90 s page 111 IDGNDI IDGNDM IDGNDS USB ID ground detect. Sense is 1 if not to ground Dual 90 s page 111 IDFACTORYI IDFACTORYM IDFACTORYS ID voltage for Factory mode detect Sense is 1 if above threshold Dual 90 s page 111 CHRGSE1BI CHRGSE1BM CHRSE1BS Wall charger detect Regulator short-circuit protection tripped Dual L2H 1.0 ms 200 s page 89 SCPI SCPS - Short circuit protection trip detection L2H 0 page 71 BATTDETBI BATTDETBM BATTDETBS Battery removal detect Dual 30 ms page 100 1HZI 1HZM - 1.0 Hz time tick L2H 0 page 49 TODAI TODAM - Time of day alarm L2H 0 page 49 PWRON1S PWRON1 event Sense is 1 if pin is high. H2L 30 ms (1) page 54 L2H 30 ms page 54 PWRON2S PWRON2 event Sense is 1 if pin is high. H2L 30 ms (47) page 54 L2H 30 ms page 54 PWRON3S PWRON3 event Sense is 1 if pin is high. H2L 30 ms (47) page 54 L2H 30 ms page 54 L2H 0 page 54 PWRON1I PWRON2I PWRON3I PWRON1M PWRON2M PWRON3M SYSRSTI SYSRSTM - System reset through PWRONx pins WDIRESETI WDIRESETM - WDI silent system restart L2H 0 page 54 PCI PCM - Power cut event L2H 0 page 54 WARMI WARMM - Warm Start event L2H 0 page 54 MEMHLDI MEMHLDM - Memory Hold event L2H 0 page 54 Dual 0 page 49 CLKI CLKM CLKS Clock source change Sense is 1 if source is XTAL RTCRSTI RTCRSTM - RTC reset or intrusion has occurred L2H 0 page 49 THWARNHI THWARNHM THWARNHS Thermal warning higher threshold Sense is 1 if above threshold Dual 30 ms page 71 THWARNLI THWARNLM THWARNLS Thermal warning lower threshold Sense is 1 if above threshold Dual 30 ms page 71 LPBI LPBM LPBS Low-power boot interrupt Dual 1.0 ms page 89 Notes 47. Debounce timing for the falling edge can be extended with PWRONxDBNC[1:0]; refer to Power Control System for details. Additional sense bits are available to reflect the state of the power up mode selection pins, as summarized in Table 13. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 47 FUNCTIONAL DEVICE OPERATION I2C INTERFACE Table 13. Additional Sense Bits Sense Description Section MODES[1:0] 00 = MODE grounded 10 = MODE to VCOREDIG 11 = MODE to VCORE page 40 PUMSxS[1:0] 00 = PUMS grounded 01 = PUMS open 10 = PUMS to VCOREDIG 11 = PUMS to VCORE page 54 CHRGSSS 0 = Single path 1 = Serial path page 89 SPECIFIC REGISTERS IDENTIFICATION The MC13892 parts can be identified though identification bits which are hardwired on chip. The version of the MC13892 can be identified by the ICID[2:0] bits. This is used to distinguish future derivatives or customizations of the MC13892. The bits are set to ICID[2:0] = 111 and are located in the revision register. The revision of the MC13892 is tracked with the revision identification bits REV[4:0]. The bits REV[4:3] track the full mask set revision, where bits REV[2:0] track the metal revisions. These bits are hardwired. Table 14. IC Revision Bit Assignment Bits REV[4:0] 10001 IC Revision Pass 3.1 The bits FIN[3:0] are Freescale use only and are not to be explored by the application. The MC13892 die is produced using different wafer fabrication plants. The plants can be identified via the FAB[1:0] bits. These bits are hardwired. MEMORY REGISTERS The MC13892 has a small general purpose embedded memory of two times 24-bits to store critical data. The data is maintained when the device is turned off and when in a power cut. The contents are only reset when a RTC reset occurs, see Clock Generation and Real Time Clock. MC13892 48 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION CLOCK GENERATION AND REAL TIME CLOCK CLOCK GENERATION AND REAL TIME CLOCK CLOCK GENERATION The MC13892 generates a 32.768 kHz clock as well as several 32.768 kHz derivative clocks that are used internally for control. Support is also provided for an external Secure Real Time Clock (SRTC) which may be integrated on a companion system processor IC. For media protection in compliance with Digital Rights Management (DRM) system requirements, the CLK32KMCU can be provided as a reference to the SRTC module where tamper protection is implemented. CLOCKING SCHEME The MC13892 contains an internal 32 kHz oscillator, that delivers a 32 kHz nominal frequency (20%) at its outputs when an external 32.768 kHz crystal is not present. If a 32.768 kHz crystal is present and running, then all control functions will run off the crystal derived 32 kHz oscillator. In absence of a valid supply at the BP supply node (for instance due to a dead battery), the crystal oscillator continues running, supplied from the coin cell battery until the coin cell is depleted. The 32 kHz clock is driven to two output pins, CLK32KMCU (intended as the CKIL input to the system processor) is referenced to VSRTC, and CLK32K (provided as a clock reference for the peripherals) is referenced to SPIVCC. The driver is enabled by the startup sequencer, and CLK32KMCU is programmable for Low-power Off mode, controlled by the state machine. Additionally, a SPI bit CLK32KMCUEN bit is provided for direct SPI control. The CLK32KMCUEN bit defaults to a 1 and resets on RTCPORB, to ensure the buffer is activated at the first power up and configured as desired for subsequent power ups. CLK32K is restricted to state machine activation in normal On mode. The drive strength of the CLK32K output drivers are programmable with CLK32KDRV[1:0] (master control bits that affect the drive strength of CLK32K). During a switchover between the two clock sources (such as when the crystal oscillator is starting up), the output clock is maintained at a stable active low or high phase of the internal 32 kHz clock to avoid any clocking glitches. If the XTAL clock source suddenly disappears during operation, the IC will revert back to the internal clock source. Given the unpredictable nature of the event and the startup times involved, the clock may be absent long enough for the application to shut down during this transition, for example, due to a sag in the switchover output voltage, or absence of a signal on the clock output pins. A status bit, CLKS, is available to indicate to the processor which clock is currently selected: CLKS=0 when the internal RC is used, and CLKS=1 if the XTAL source is used. The CLKI interrupt bit will be set whenever a change in the clock source occurs, and an interrupt will be generated if the corresponding CLKM mask bit is cleared. OSCILLATOR SPECIFICATIONS The crystal oscillator has been designed for use in conjunction with the Micro Crystal CC7V-T1A-32.768 kHz-9pF-30 ppm or equivalent (such as Micro Crystal CC5V-T1A or Epson FC135). Table 15. RTC Crystal Specifications Nominal Frequency 32.768 kHz Make Tolerance +/-30 ppm Temperature Stability -0.038 ppm /C2 Series Resistance 80 kOhm Maximum Drive Level 1.0 W Operating Drive Level 0.25 to 0.5 W Nominal Load Capacitance 9.0 pF Pin-to-pin Capacitance 1.4 pF Aging 3 ppm/year The oscillator also accepts a clock signal from an external source. This clock signal is to be applied to the XTAL1 pin, where the signal can be DC or AC coupled. A capacitive divider can be used to adapt the source signal to the XTAL1 input levels. When applying an external source, the XTAL2 pin is to be connected to VCOREDIG. The electrical characteristics of the 32 kHz Crystal oscillator are given in the table below, taking into account the above crystal characteristics MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 49 FUNCTIONAL DEVICE OPERATION CLOCK GENERATION AND REAL TIME CLOCK Table 16. Crystal Oscillator Main Characteristics Parameter Condition Min Typ Max Units Operating Voltage Oscillator and RTC Block from BP 1.2 - 4.65 Coin cell Disconnect Threshold At LICELL 1.8 - 2.0 V RTC oscillator startup time Upon application of power - - 1.0 sec XTAL1 Input Level External clock source 0.3 - - VPP XTAL1 Input Range External clock source -0.5 - 1.2 V Output Low CLK32K, CLK32KMCU Output sink 100 A 0 - 0.2 V CLK32K Output source 100 A SPIVCC-0.2 - SPIVCC V CLK32KMCU Output source 100 A VSRTC-0.2 - VSRTC V CLK32KDRV[1:0] = 00 (default) - 22 - ns CLK32KDRV[1:0] = 01 - 11 - ns CLK32KDRV[1:0] = 10 - High Z - ns CLK32KDRV[1:0] = 11 - 44 - ns CLD32KMCU Rise and Fall Time CL=12 pF - 22 - ns CLK32K and CLK32KMCU Output Duty Cycle Crystal on XTAL1, XTAL2 pins 45 - 55 % Output High V CL=50 pF CLK32K Rise and Fall Time OSCILLATOR APPLICATION GUIDELINES The guidelines below may prove to be helpful in providing a crystal oscillator that starts reliably and runs with minimal jitter. PCB leakage: The RTC amplifier is a low-current circuit. Therefore, PCB leakage may significantly change the operating point of the amplifier and even the drive level to the crystal. (Changing the drive level to the crystal may change the aging rate, jitter, and even the frequency at a given load capacitance.) The traces should be kept as short as possible to minimize the leakage, and good PCB manufacturing processes should be maintained. Layout: The traces from the MC13892 to the crystal, load capacitance, and the RTC Ground are sensitive. They must be kept as short as possible with minimal coupling to other signals. The signal ground for the RTC is to be connected to GNDRTC, and via a single connection, GNDRTC to the system ground. The CLK32K and CLK32KMCU square wave outputs must be kept away from the crystal / load capacitor leads, as the sharp edges can couple into the circuit and lead to excessive jitter. The crystal / load capacitance leads and the RTC Ground must form a minimal loop area. Crystal Choice: Generally speaking, crystals are not interchangeable between manufacturers, or even different packages for a given manufacturer. If a different crystal is considered, it must be fully characterized with the MC13892 before it can be considered. Tuning Capacitors: The nominal load capacitance is 9.0 pF, therefore the total capacitance at each node should be 18 pF, composed out of the load capacitance, the effective input capacitance at each pin, plus the PCB stray capacitance for each pin. SRTC SUPPORT The MC13892 provides support for processors which have an integrated SRTC for Digital Rights Management (DRM), by providing a VSRTC voltage to bias the SRTC module of the processor, as well as a CLK32KMCU at the VSRTC output level. When configured for DRM mode (SPI bit DRM = 1), the CLK32MCU driver will be kept enabled through all operational states, to ensure that the SRTC module always has its reference clock. If DRM = 0, the CLK32KMCU driver will not be maintained in the Off state. Refer to Table 23 for the operating behavior of the CLK32KMCU output in User Off, Memory Hold, User off Wait, and internal MEMHOLD PCUT modes. It is also necessary to provide a means for the processor to do an RTC initiated wake-up of the system, if it has been programmed for such capability. This can be accomplished by connecting an open drain NMOS driver to the PWRON pin of the MC13892, so that it is in effect a parallel path for the power key. The MC13892 will not be able to discern the turn on event from a normal power key initiated turn on, but the processor should have the knowledge, since the RTC initiated turn on is generated locally. MC13892 50 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION CLOCK GENERATION AND REAL TIME CLOCK Figure 10. SRTC block diagram VSRTC The VSRTC regulator provides the CLK32KMCU output level. It is also used to bias the Low-power SRTC domain of the SRTC module integrated on certain FSL processors. The VSRTC regulator is enabled as soon as the RTCPORB is detected. The VSRTC cannot be disabled. Table 17. VSRTC Specifications Parameter Condition Min Typ Max Units General Operating Input Voltage Range, VINMIN to VINMAX Valid Coin Cell range or valid BP Operating Current Load Range ILMIN to ILMAX Bypass Capacitor Value 1.8 - 3.6 V UVDET - 4.65 V 0.0 - 50 A - 1.0 - F 1.150 1.20 1.25 V Active Mode - DC Output Voltage VOUT VINMIN < VIN < VINMAX ILMIN < IL < ILMAX REAL TIME CLOCK A real Time Clock (RTC) function is provided including time and day counters as well as an alarm function. The utilizes a 32 kHz clock, either the RC oscillator or the 32.768 kHz crystal oscillator as a time base, and is powered by the coin cell backup supply when BP has dropped below operational range. In configurations where the SRTC is used, the RTC can be disabled to conserve current drain by setting the RTCDIS bit to a 1 (defaults on at power up). TIME AND DAY COUNTERS The 32 kHz clock is divided down to a 1.0 Hz time tick which drives a 17-bit Time Of Day (TOD) counter. The TOD counter counts the seconds during a 24 hour period from 0 to 86,399, and will then roll over to 0. When the roll over occurs, it increments the 15-bit DAY counter. The DAY counter can count up to 32767 days. The 1.0 Hz time tick can be used to generate a 1HZI interrupt if unmasked. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 51 FUNCTIONAL DEVICE OPERATION CLOCK GENERATION AND REAL TIME CLOCK TIME OF DAY ALARM A Time Of Day Alarm (TODA) function can be used to turn on the application and alert the processor. If the application is already on, the processor will be interrupted. The TODA and DAYA registers are used to set the alarm time. Only a single alarm can be programmed at a time. When the TOD counter is equal to the value in TODA, and the DAY counter is equal to the value in DAYA, the TODAI interrupt will be generated. At initial power up of the application (application of the coin cell), the state of the TODA and DAYA registers will be all 1's. The interrupt for the alarm (TODAI) is backed up by LICELL and will be valid at power up. If the mask bit for the TOD alarm (TODAM) is high, then the TODAI interrupt is masked and the application will not turn on with the time of day alarm event (TOD[16:0] = TODA[16:0] and DAY[14:0] = DAYA[14:0]). By default, the TODAM mask bit is set to 1, thus masking the interrupt and turn on event. TIMER RESET As long as the supply at BP is valid, the real time clock will be supplied from VCORE. If not, it can be backed up from a coin cell via the LICELL pin. When the backup voltage drops below RTCUVDET, the RTCPORB reset signal is generated and the contents of the RTC will be reset. Additional registers backed up by coin cell will also reset with RTCPORB. To inform the processor that the contents of the RTC are no longer valid due to the reset, a timer reset interrupt function is implemented with the RTCRSTI bit. RTC TIMER CALIBRATION A clock calibration system is provided to adjust the 32,768 cycle counter that generates the 1.0 Hz timer for RTC timing registers to comply with digital rights management specifications of 50 ppm. This calibration system can be disabled, if not needed to reduce the RTC current drain. The general implementation relies on the system processor to measure the 32.768 kHz crystal oscillator against a higher frequency and more accurate system clock such as a TCXO. If the RTC timer needs a correction, a 5-bit 2's complement calibration word can be sent via the SPI to compensate the RTC for inaccuracy in its reference oscillator as defined in Table 18. Table 18. RTC Calibration Settings Code in RTCCAL[4:0] Correction in Counts per 32768 Relative correction in ppm 01111 +15 +458 00011 +3 +92 00001 +1 +31 00000 0 0 11111 -1 -31 11101 -3 -92 10001 -15 -458 10000 -16 -488 Note that the 32.768 kHz oscillator is not affected by RTCCAL settings. Calibration is only applied to the RTC time base counter. Therefore, the frequency at the clock outputs CLK32K and CLK32KMCU are not affected. The RTC system calibration is enabled by programming the RTCCALMODE[1:0] for desired behavior by operational mode. Table 19. RTC Calibration Enabling RTCCALMODE Function 00 RTC Calibration disabled (default) 01 RTC Calibration enabled in all modes except coin cell only 10 Reserved for future use. Do not use. 11 RTC Calibration enabled in all modes A slight increase in consumption will be seen when the calibration circuitry is activated. To minimize consumption and maximize lifetime when the RTC system is maintained by the coin cell, the RTC Calibration circuitry can be automatically disabled when main battery contact is lost, or if it is so deeply discharged that RTC power draw is switched to the coin cell (configured with RTCCALMODE = 01). Because of the low RTC consumption, RTC accuracy can be maintained through long periods of the application being shut down, even after the main battery has discharged. However, it is noted that the calibration can only be as good as the RTCCAL MC13892 52 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION CLOCK GENERATION AND REAL TIME CLOCK data that has been provided, so occasional refreshing is recommended to ensure that any drift influencing environmental factors have not skewed the clock beyond desired tolerances. COIN CELL BATTERY BACKUP The LICELL pin provides a connection for a coin cell backup battery or supercap. If the main battery is deeply discharged, removed, or contact-bounced (i.e., during a power cut), the RTC system and coin cell maintained logic will switch over to the LICELL for backup power. This switch over occurs for a BP below the UVDET threshold with LICELL greater than BP. A small capacitor should be placed from LICELL to ground under all circumstances. Upon initial insertion of the coincell, it is not immediately connected to the on chip circuitry. The cell gets connected when the IC powers on, or after enabling the coincell charger when the IC was already on. During operation, coincells can get damaged and their lifetime reduced when deeply discharged. In order to avoid such, the internal circuitry supplied from LICELL is automatically disconnected for voltages below the coincell disconnect threshold. The cell gets reconnected again under the same conditions as for initial insertion. The coin cell charger circuit will function as a current-limited voltage source, resulting in the CC/CV taper characteristic typically used for rechargeable Lithium-Ion batteries. The coin cell charger is enabled via the COINCHEN bit. The coin cell voltage is programmable through the VCOIN[2:0] bits. The coin cell charger voltage is programmable in the ON state where the charge current is fixed at ICOINHI. If COINCHEN=1 when the system goes into Off or User Off state, the coin cell charger will continue to charge to the predefined voltage setting but at a lower maximum current ICOINLO. This compensates for self discharge of the coin cell and ensures that if/when the main cell gets depleted, that the coin cell will be topped off for maximum RTC retention. The coin cell charging will be stopped for the BP below UVDET. The bit COINCHEN itself is only cleared when an RTCPORB occurs. Table 20. Coin cell Charger Voltage Specifications VCOIN[2:0] Output Voltage 000 2.50 001 2.70 010 2.80 011 2.90 100 3.00 101 3.10 110 3.20 111 3.30 Table 21. Coin cell Charger Specifications Typ Units Voltage Accuracy Parameter 100 mV Coin Cell Charge Current in On and Watchdog modes ICOINHI 60 A Coin Cell Charge Current in Off and Low-power Off modes (User Off / Memory Hold) ICOINLO 10 A Current Accuracy 30 % LICELL Bypass Capacitor 100 nF LICELL Bypass Capacitor as coin cell replacement 4.7 F LICELL Bypass Capacitor 100 nF LICELL Bypass Capacitor as coin cell replacement 4.7 F MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 53 FUNCTIONAL DEVICE OPERATION POWER CONTROL SYSTEM POWER CONTROL SYSTEM INTERFACE The power control system on the MC13892 interfaces with the processor via different IO signals and the SPI/I2C bus. It also uses on chip signals and detector outputs. Table 22 gives a listing of the principal elements of this interface. Table 22. Power Control System Interface Signals Name Type of Signal Function PWRON1 Input pin Power on/off 1 button connection PWRON2 Input pin Power on/off 2 button connection PWRON3 Input pin Power on/off 3 button connection PWRONxI/M/S SPI bits PWRONx pin interrupt /mask / sense bits PWRON1DBNC[1:0] SPI bits Sets time for the PWRON1 pin hardware debounce PWRON2DBNC[1:0] SPI bits Sets time for the PWRON2 pin hardware debounce PWRON3DBNC[1:0] SPI bits Sets time for the PWRON3 pin hardware debounce PWRON1RSTEN SPI bit Allows for system reset through the PWRON1 pin PWRON2RSTEN SPI bit Allows for system reset through the PWRON2 pin PWRON3RSTEN SPI bit Allows for system reset through the PWRON3 pin RESTARTEN SPI bit Allows for system restart after a PWRON initiated system reset SYSRSTI/M SPI bits PWRONx System restart interrupt / mask bits WDI Input pin Watchdog input has to be kept high by the processor to keep the MC13892 active WDIRESET SPI bit Allows for system restart through the WDI pin WDIRESETI/M SPI bits WDI System restart interrupt / mask bits RESET Output pin Reset Bar output (active low) to the application. Requires an external pull-up RESETMCU Output pin Reset Bar output (active low) to the processor core. Requires an external pull-up PUMS1 Input pin Switchers and regulators power up sequence and defaults selection 1 PUMS2 Input pin Switchers and regulators power up sequence and defaults selection 2 STANDBY Input pin Signal from primary processor to put the MC13892 in a Low-power mode STANDBYINV SPI bit STANDBYSEC Input pin Standby signal polarity setting Signal from secondary processor to put the MC13892 in a Low-power mode STANDBYSECINV SPI bit Secondary standby signal polarity setting STBYDLY[1:0] SPI bits Sets delay before entering standby mode BPON BPONI/M/S LOBATH LOBATHI/M/S LOBATL Threshold SPI bits Threshold SPI bits Threshold Threshold validating turn on events BP turn on threshold interrupt / mask / sense bits Threshold for a low battery warning Low battery warning interrupt / mask / sense bits Threshold for a low battery detect LOBATLI/M/S SPI bits Low battery detect interrupt / mask / sense bits BPSNS [1:0] SPI bits Selects for different settings of LOBATL and LOBATH thresholds UVDET Threshold Threshold for under-voltage detection, will shut down the device LICELL Input pin Connection for Lithium based coin cell CLK32KMCU Output pin Low frequency system clock output for the processor 32.768 kHz CLK32K Output pin Low frequency system clock output for application (peripherals) 32.768 kHz CLK32KMCUEN SPI bit Enables the CLK32KMCU clock output DRM SPI bit Keeps VSRTC and CLK32KMCU active in all states for digital rights management, including off mode PCEN SPI bit Enables power cut support PCI/M SPI bits Power cut detect interrupt / mask bits PCT[7:0] SPI bits Allowed power cut duration PCCOUNTEN SPI bit Enables power cut counter PCCOUNT[3:0] SPI bits Power cut counter MC13892 54 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION POWER CONTROL SYSTEM Table 22. Power Control System Interface Signals Name Type of Signal Function PCMAXCNT[3:0] SPI bits Maximum number of allowed power cuts PCUTEXPB SPI bit Indicates a power cut timer counter expired MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 55 FUNCTIONAL DEVICE OPERATION OPERATING MODES OPERATING MODES POWER CONTROL STATE MACHINE Figure 11 shows the flow of the power control state machine. This diagram serves as the basis for the description in the remainder of this chapter. Figure 11. Power Control State Machine Flow Diagram MC13892 56 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION OPERATING MODES POWER CONTROL MODES DESCRIPTION Following are text descriptions of the power states of the system, which give additional details of the state machine, and complement Figure 11. Note that the SPI control is only possible in the Watchdog, On, and User Off Wait states, and that the interrupt line INT is kept low in all states except for Watchdog and On. Off If the supply at BP is above the UVDET threshold, only the IC core circuitry at VCOREDIG and the RTC module are powered, all other supplies are inactive. To exit the Off mode, a valid turn on event is required. No specific timer is running in this mode. If the supply at BP is below the UVDET threshold no turn on events are accepted. If a valid coin cell is present, the core gets powered from LICELL. The only active circuitry is the RTC module, with BP greater than UVDET detection, and the SRTC support circuitry, if so configured. Cold Start Entered upon a Turn On event from Off, Warm Boot, successful PCUT, or Silent System Restart. The switchers and regulators are powered up sequentially to limit the inrush current. See the Power Up section for sequencing and default level details. The reset signals RESETB and RESETBMCU are kept low. The Reset timer starts running when entering a Cold Start. When expired, the Cold Start state is exited for the Watchdog state, and both RESETB and RESETBMCU become high (open drain output with external pull ups). The input control pins WDI, and STANDBYx are ignored. Watchdog The system is fully powered and under SPI control. RESETB and RESETBMCU are high. The Watchdog timer starts running when entering the Watchdog state. When expired, the system transitions to the On state, where WDI will be checked and monitored. The input control pins WDI and STANDBYx are ignored while in the Watchdog state. On The system is fully powered and under SPI control. RESETB and RESETBMCU are high. The WDI pin must be high to stay in this mode. The WDI IO supply voltage is referenced to SPIVCC (Normally connected to SW4). SPIVCC must therefore remain enabled to allow for proper WDI detection. If WDI goes low, the system will transition to the Off state or Cold Start (depending on the configuration. Refer to the section on Silent System Restart with WDI Event for details). User Off Wait The system is fully powered and under SPI control. The WDI pin no longer has control over the part. The Wait mode is entered by a processor request for User Off by setting the USEROFFSPI bit high. This is normally initiated by the end user via the power key. Upon receiving the corresponding interrupt, the system will determine if the product has been configured for User Off or Memory Hold states (both of which first require passing through User Off Wait) or just transition to Off. The Wait timer starts running when entering User Off Wait mode. This leaves the processor time to suspend or terminate its tasks. When expired, the Wait mode is exited for User Off mode or Memory Hold mode, depending on warm starts being enabled or not via the WARMEN bit. The USEROFFSPI bit is being reset at this point by RESETB going low. Memory Hold and User Off (Low-power Off states) As noted in the User Off Wait description, the system is directed into Low-power Off states based on a SPI command in response to an intentional turn off by the end user. The only exit then will be a turn on event. To an end user, the Memory Hold and User Off states look like the product has been shut down completely. However, a faster startup is facilitated by maintaining external memory in self-refresh mode (Memory Hold and User Off mode) as well as powering portions of the processor core for state retention (User Off only). The switcher mode control bits allow selective powering of the buck regulators for optimizing the supply behavior in the Low-power Off modes. Linear regulators and most functional blocks are disabled (the RTC module, and Turn On event detection are maintained). Memory Hold RESETB and RESETBMCU are low, and both CLK32K and CLK32KMCU are disabled. If DRM is set, the CLK32KMCU is kept active. To ensure that SW1, SW2, and SW3 shut off in Memory Hold, appropriate mode settings should be used such as SW1MHMODE = SW2MHMODE = SW3MHMODE = 0 (refer to the mode control description later in this chapter). Since SW4 should be powered in PFM mode, SW4MHMODE could be set to 1. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 57 FUNCTIONAL DEVICE OPERATION OPERATING MODES Any peripheral loading on SW4 should be isolated from the SW4 output node by the PWGT2 switch, which opens in both Lowpower off modes due to the RESETB transition. In this way, leakage is minimized from the power domain maintaining the memory subsystem. Upon a Turn On event, the Cold Start state is entered, the default power up values are loaded, and an the MEMHLDI interrupt bit is set. A Cold Start out of the Memory Hold state will result in shorter boot times compared to starting out of the Off state, since software does not have to be loaded and expanded from flash. The startup out of Memory Hold is also referred to as Warm Boot. No specific timer is running in this mode. Buck regulators that are configured to stay on in MEMHOLD mode by their SWxMHMODE settings will not be turned off when coming out of MEMHOLD and entering a Warm Boot. The switchers will be reconfigured for their default settings as selected by the PUMS pin in the normal time slot that would affect them. User Off RESETB is low and RESETBMCU is kept high. The 32 kHz peripheral clock driver CLK32K is disabled. CLK32KMCU (connected to the processor's CKIL input) is maintained in this mode if the CLK32KMCUEN and USEROFFCLK bits are both set, or if DRM is set. The memory domain is held up by setting SW4UOMODE = 1. Similarly, the SW1, and/or SW2, and/or SW3 supply domains can be configured for SWxUOMODE = 1 to keep them powered through the User Off event. If one of the switchers can be shut down on in User Off, its mode bits would typically be set to 0. Any peripheral loading on SW1 and/or SW2 should be isolated from the output node(s) by the PWGT1 switch, which opens in both Low-power Off modes due to the RESETB transition. In this way, leakage is minimized from the power domain maintaining the processor core. Since power is maintained for the core (which is put into its lowest power state) and since MCU RESETBMCU does not trip, the processor's state may be quickly recovered when exiting USEROFF upon a turn on event. The CLK32KMCU clock can be used for very low frequency / low-power idling of the core(s), minimizing battery drain while allowing a rapid recovery from where the system left off before the USEROFF command. Upon a turn on event, Warm Start state is entered, and the default power up values are loaded. A Warm Start out of User Off will result in an almost instantaneous startup of the system, since the internal states of the processor were preserved along with external memory. No specific timer is running in this mode. Warm Start Entered upon a Turn On event from User Off. The switchers and regulators are powered up sequentially to limit the inrush current; see the Power Up section for sequencing and default level details. If SW1, SW2, SW3, and/or SW4 were configured to stay on in User Off mode, they will not be turned off when coming out of User Off and entering a Warm Start. The buck regulators will be reconfigured for their default settings as selected by the PUMS pin in the respective time slot defined in the sequencer selection. RESETB is kept low and RESETBMCU is kept high. CLK32KMCU is kept active if enabled via the SPI. The reset timer starts running when entering Warm Start. When expired, the Warm Start state is exited for the Watchdog state, a WARMI interrupt is generated, and RESETB will go high. Internal MemHold Power Cut Refer to the next section for details about Power Cuts and the associated state machine response. POWER CUT DESCRIPTION When the supply at BP drops below the UVDET threshold due to battery bounce or battery removal, the Internal MemHold Power Cut mode is entered and a Power Cut (PCUT) timer starts running. The backup coin cell will now supply the RTC as well as the on chip memory registers and some other power control related bits. All other supplies will be disabled. The maximum duration of a power cut is determined by the PCUT timer PCT[7:0] preset via SPI. When a PCUT occurs, the PCUT timer will internally be decremented till it expires, meaning counted down to zero. The contents of PCT[7:0] does not reflect the actual count down value but will keep the programmed value and therefore does not have to be reprogrammed after each power cut. If power is not reestablished above BPON before the PCUT timer expires, the state machine transitions to the Off mode at expiration of the counter, and clears the PCUTEXB bit by setting it to 0. This transition is referred to as an "unsuccessful" PCUT. Upon re-application of power before expiration (an "successful PCUT", defined as BP first rising above the UVDET threshold and then above the BPON threshold before the PCUT timer expires), a Cold Start is engaged. MC13892 58 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION OPERATING MODES In order to distinguish a non-PCUT initiated Cold Start from a Cold Start after a PCUT, the PCI interrupt should be checked by software. The PCI interrupt is cleared by software or when cycling through the Off state. Because the PCUT system quickly disables all of the power tree, the battery voltage may recover to a level with the appearance of a valid supply once the battery is unloaded. However, upon a restart of the IC and power sequencer, the surge of current through the battery and trace impedances can once again cause the BP node to drop below UVDET. This chain of cyclic power down / power up sequences is referred to as "ambulance mode", and the power control system includes strategies to minimize the chance of a product falling into and getting stuck in ambulance mode. First, the successful recovery out of a PCUT requires the BP node to rise above BPON, providing hysteretic margin from the UVDET threshold. Secondly, the number of times the PCUT mode is entered is counted with the counter PCCOUNT[3:0], and the allowed count is limited to PCMAXCNT[3:0] set through the SPI. When the contents of both become equal, then the next PCUT will not be supported and the system will go to Off mode. After a successful power up after a PCUT (i.e., valid power is reestablished, the system comes out of reset, and the processor reassumes control), software should clear the PCCOUNT[3:0] counter. Counting of PCUT events is enabled via the PCCOUNTEN bit. This mode is only supported if the power cut mode feature is enabled by setting the PCEN bit. When not enabled, in case of a power failure, the state machine will transition to the Off state. SPI control is not possible during a PCUT event and the interrupt line is kept low. SPI configuration for PCUT support should also include setting the PCUTEXPB=1 (see the Silent Restart from PCUT Event section later in this chapter). Internal MemHold Power Cut As described above, a momentary power interruption will put the system into the Internal MemHold Power Cut state if PCUTs are enabled. The backup coin cell will now supply the MC13892 core along with the 32 kHz crystal oscillator, the RTC system and coin cell backed up registers. All regulators and switchers will be shut down to preserve the coin cell and RTC as long as possible. Both RESETB and RESETBMCU are tripped, bringing the entire system down along with the supplies and external clock drivers, so the only recovery out of a Power Cut state is to reestablish power and initiate a Cold Start. If the PCT timer expires before power is reestablished, the system transitions to the Off state and awaits a sufficient supply recovery. SILENT RESTART FROM PCUT EVENT If a short duration power cut event occurs (such as from a battery bounce, for example), it may be desirable to perform a silent restart, so the system is re-initialized without alerting the user. This can be configured by setting the PCUTEXPB bit to a "1" at booting or after a Cold Start. This bit resets on RTCPORB, therefore any subsequent Cold Start can first check the status of PCUTEXPB and the PCI bit. The PCUTEXPB is cleared to "0" when transitioning from PCUT to Off. If there was a PCUT interrupt and PCUTEXPB is still a "1", then the state machine has not transitioned through Off, which confirms that the PCT timer has not expired during the PCUT event (i.e., a successful power cut). In case of a successful power cut, a silent restart may be appropriate. If PCUTEXPB is found to be a "0" after the Cold Start where PCI is found to be a "1", then it is inferred that the PCT timer has expired before power was reestablished, flagging an unsuccessful power cut or first power up, so the startup user greeting may be desirable for playback. SILENT SYSTEM RESTART WITH WDI EVENT A mechanism is provided for recovery if the system software somehow gets into an abnormal state which requires a system reset, but it is desired to make the reset a silent event so as to happen without end user awareness. The default response to WDI going low is for the state machine to transition to the Off state (when WDIRESET = 0). However, if WDIRESET = 1, the state machine will go to Cold Start without passing through Off mode A WDIRESET event will generate a maskable WDIRESETI interrupt and also increment the PCCOUNT counter. This function is unrelated to PCUTs, but it shares the PCUT counter so that the number of silent system restarts can be limited by the programmable PCMAXCNT counter. When PCUT support is used, the software should set the PCUTEXPB bit to "1". Since this bit resets with RTCPORB, it will not be reset to "0" if a WDI falls and the state machine goes straight to the Cold Start state. Therefore, upon a restart, the software can detect a silent system restart, if there is a WDIRESETI interrupt and PCUTEXPB = 1. The application may then determine that an inconspicuous restart without showing may be more appropriate than launching into the welcoming routine. A PCUT event does not trip the WDIRESETI bit. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 59 FUNCTIONAL DEVICE OPERATION OPERATING MODES GLOBAL SYSTEM RESTART A global system reset can be enabled through the GLBRSTENB SPI bit. The global reset on the MC13892A/C versions is active low so it is enabled when the GLBRSTENB = 0. In the MC13892B/D versions global reset is active high and it is enabled when the GLBRSTENB = 1. When global reset is enabled and the PWRON3 button is held for 12 seconds, the system will reset and the following actions will take place: * Power down * Disable the charger * Reset all the registers including the RTCPORB registers * Power back up after the difference between the 12 sec timer, and when the user releases the button as the power off time (for example, if the power button was held for 12.1 s, then the time that the IC would be off would be only 100 mS) If PWRON3 is held low for less than 12 seconds, it will act as a normal PWRON pin. This feature is enabled by default in the MC13892A/C versions, and disabled by default in the MC13892B/D versions. CLK32KMCU CLOCK DRIVER CONTROL THROUGH STATES As described previously, the clocking behavior is influenced by the state machine is in and the setting of the clocking related SPI bits. A summary is given in Table 23 for the clock output CLK32KMCU. Table 23. CLK32MCU Control Logic Table Mode DRM Off, Memory Hold, Internal MEMHOLD PCUT On, Cold Start, Warm Start, Watchdog, User Off Wait User Off CLK32KMCUEN USEROFFCLK Clock Output CLK32KMCU 0 X X Disabled 1 X X Enabled 0 0 X Disabled 1 X X Enabled 0 1 X Enabled 0 X 0 Disabled 1 X X 0 1 1 Enabled TURN ON EVENTS When in Off mode, the MC13892 can be powered on via a Turn On event. The Turn On events are listed in Table 24. To indicate to the processor what event caused the system to power on, an interrupt bit is associated with each of the Turn On events. Masking the interrupts related to the turn on events will not prevent the part to turn on, except for the time of day alarm. Power Button Press PWRON1, PWRON2, or PWRON3 pulled low with corresponding interrupts and sense bits PWRON1I, PWRON2I, or PWRON3I, and PWRON1S, PWRON2S, or PWRON3S. A power on/off button is connected here. The PWRONx can be hardware debounced through a programmable debouncer PWRONxDBNC[1:0] to avoid the application to power up upon a very short key press. In addition, a software debounce can be applied. BP should be above UVDET. The PWRONxI interrupt is generated for both the falling and the rising edge of the PWRONx pin. By default, a 30 ms interrupt debounce is applied to both falling and rising edges. The falling edge debounce timing can be extended with PWRONxDBNC[1:0] as defined in the following table. The PWRONxI interrupt is cleared by software or when cycling through the Off mode. Table 24. PWRONx Hardware Debounce Bit Settings Bits PWRONxDBNC[1:0] State Turn On Debounce (ms) Falling Edge INT Debounce (ms) Rising Edge INT Debounce (ms) 00 0 31.25 31.25 01 31.25 31.25 31.25 10 125 125 31.25 11 750 750 31.25 Notes 48. The sense bit PWRONxS is not debounced and follows the state of the PWRONx pin MC13892 60 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION OPERATING MODES Charger Attach CHRGRAW is pulled high with corresponding interrupt and sense bits CHGDETI and CHGDETS. This is equivalent to plugging in a charger. BP should be above BPON. The charger turn on event is dependent on the charge mode selected. For details on the charger detection and turn on, see Battery Interface and Control. Battery Attach BP crossing the BPON threshold which corresponds to attaching a charged battery to the product. A corresponding BPONI interrupt is generated, which can be cleared by software or when cycling through the Off mode. Note that BPONI is also generated after a successful power cut and potentially when applying a charger. USB Attach VBUS pulled high with corresponding interrupt and sense bits BVALIDI and BVALIDS. This is equivalent to plugging in a USB cable. BP should be above BPON and the battery voltage above BATTON. For details on the USB detection, see Connectivity. RTC Alarm TOD and DAY become equal to the alarm setting programmed. This allows powering up a product at a preset time. BP should be above BPON. For details and related interrupts, see Clock Generation and Real Time Clock. System Restart System restart may occur after a system reset. This is an optional function, see also the following Turn Off events section. BP should be above BPON. TURN OFF EVENTS Power Button Press User shut down of a product is typically done by pressing the power button connected to the PWRONx pin. This will generate an interrupt (PWRONxI), but will not directly power off the part. The product is powered off by the processor's response to this interrupt, which will be to pull WDI low. Pressing the power button is therefore under normal circumstances not considered as a turn off event for the state machine. Note that software can configure a user initiated power down via a power button press for transition to a Low-power off mode (Memory Hold or User Off) for a quicker restart than the default transition into the Off state. Power Button System Reset A secondary application of the PWRON pin is the option to generate a system reset. This is recognized as a Turn Off event. By default, the system reset function is disabled but can be enabled by setting the PWRONxRSTEN bits. When enabled, a 4 second long press on the power button will cause the device to go to the Off mode and as a result the entire application will power down. An SYSRSTI interrupt is generated upon the next power up. Alternatively, the system can be configured to restart automatically by setting the RESTARTEN bit. Thermal Protection If the die gets overheated, the thermal protection will power off the part to avoid damage. A Turn On event will not be accepted while the thermal protection is still being tripped. The part will remain in Off mode until cooling sufficiently to accept a Turn On event. There are no specific interrupts related to this other than the warning interrupts. Under-Voltage Detection When the voltage at BP drops below the under-voltage detection threshold UVDET, the state machine will transition to Off mode if PCUT is not enabled, or if the PCT timer expires when PCUT is enabled. TIMERS The different timers as used by the state machine are in Table 25. This listing does not include RTC timers for timekeeping. A synchronization error of up to one clock period may occur with respect to the occurrence of an asynchronous event. The duration listed below is therefore the effective minimum time period. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 61 FUNCTIONAL DEVICE OPERATION OPERATING MODES Table 25. Timer Main Characteristics Timer Duration Under-voltage Timer 4.0 ms Reset Timer 40 ms Watchdog Timer 128 ms Power Cut Timer Programmable 0 to 8 seconds in 31.25 ms steps TIMING DIAGRAMS A Turn On event timing diagram example shows in Figure 12. Figure 12. Power Up Timing Diagram POWER UP At power up, switchers and regulators are sequentially enabled in time slots of 2.0 ms steps to limit the inrush current after an initial delay of 8.0 ms, in which the core circuitry gets enabled. To ensure a proper power up sequence, the outputs of the switchers are discharged at the beginning of a Cold Start. For that reason, an 8.0 ms delay allows the outputs of the linear regulators to be fully discharged as well through the built-in discharge path. Time slots which include multiple regulator startups will be sub-sequenced for additional inrush balancing. The peak inrush current per event is limited. Any under-voltage detection at BP is masked while the power up sequencer is running. The Power Up mode Select pins (PUMS1 and 2) are used to configure the startup characteristics of the regulators. Supply enabling and output level options are selected by hardwiring the PUMSx pins for the desired configuration. The state of the PUMSx pins can be read out via the sense bits PUMSSxx[1:0]. Tying the PUMSx pins to ground corresponds to 00, open to 01, VCOREDIG to 10, and VCORE to 11. The recommended power up strategy for end products is to bring up as little of the system as possible at booting, essentially sequestering just the bare essentials, to allow processor startup and software to run. With such a strategy, the startup transients are controlled at lower levels, and the rest of the system power tree can be brought up by software. This allows optimization of supply ordering where specific sequences may be required, as well as supply default values. Software code can load up all of the required programmable options to avoid sneak paths, under/over-voltage issues, startup surges, etc., without any change in hardware. For this reason, the Power Gate drivers are limited to activation by software rather than the sequencer, allowing the core(s) to startup before any peripheral loading is introduced. The power up defaults Table 26 shows the initial setup for the voltage level of the switchers and regulators, and whether they get enabled. MC13892 62 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION OPERATING MODES Table 26. Power Up Defaults Table i.MX 37/51 37/51 37/51 37/51 35 27/31 PUMS1 GND Open VCOREDIG VCORE GND Open PUMS2 Open Open Open Open GND GND (49) 0.775 1.050 1.050 0.775 1.200 1.200 SW2 (49) 1.025 1.225 1.225 1.025 1.350 1.450 SW3 (49) 1.200 1.200 1.200 1.200 1.800 1.800 SW4 (49) 1.800 1.800 1.800 1.800 1.800 1.800 SWBST Off Off Off Off 5.000 5.000 VUSB 3.300 (50) 3.300 (50) 3.300 (50) 3.300 (50) 3.300 (52) 3.300 (52) VUSB2 2.600 2.600 2.600 2.600 2.600 2.600 VPLL 1.800 1.800 1.800 1.800 1.500 1.500 VDIG 1.250 1.250 1.250 1.250 1.250 1.250 VIOHI 2.775 2.775 2.775 2.775 2.775 2.775 VGEN2 3.150 Off 3.150 Off 3.150 3.150 VSD Off Off Off Off 3.150 3.150 SW1 Notes 49. The switchers SWx are activated in PWM pulse skipping mode, but allowed when enabled by the startup sequencer. 50. USB supply VUSB, is only enabled if 5.0 V is present on UVBUS. 51. The following supplies are not included in the matrix since they are not intended for activation by the startup sequencer: VCAM, VGEN1, VGEN3, VVIDEO, and VAUDIO 52. SWBST = 5.0 V powers up and does VUSB regardless of 5.0 V present on UVBUS. By default VUSB will be supplied by SWBST. The power up sequence is shown in Table 27. VCOREDIG, VSRTC, and VCORE are brought up in the pre-sequencer startup. Once VCOREDIG is activated (i.e., at the first-time power application), it will be continuously powered as long as a valid coin cell is present. Table 27. Power Up Sequence Tap x 2ms PUMS2 = Open (i.MX37, i.MX51) PUMS2 = GND (i.MX35, i.MX27) 0 SW2 SW2 1 SW4 VGEN2 2 VIOHI SW4 3 VGEN2 VIOHI, VSD 4 SW1 SWBST, VUSB (56) 5 SW3 SW1 6 VPLL VPLL 7 VDIG SW3 8 - VDIG 9 VUSB (55), VUSB2 VUSB2 Notes 53. Time slots may be included for blocks which are defined by the PUMS pin as disabled to allow for potential activation. 54. The following supplies are not included in the matrix since they are not intended for activation by the startup sequencer: VCAM, VGEN1, VGEN3, VVIDEO, and VAUDIO. SWBST is not included on the PUMS2 = Open column. 55. USB supply VUSB, is only enabled if 5.0 V is present on UVBUS. 56. SWBST = 5.0 V powers up and so does VUSB regardless of 5.0 V present on UVBUS. By default VUSB will be supplied by SWBST. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 63 FUNCTIONAL DEVICE OPERATION OPERATING MODES POWER MONITORING The voltage at BPSNS and BP is monitored by detectors as summarized in Table 28. Table 28. BP Detection Thresholds Threshold in V Bit setting BPSNS1 Falling Edge BPSNS0 UVDET Rising Edge LOBATL LOBATH BPON 0 0 2.55 2.8 3.0 3.2 0 1 2.55 2.9 3.1 3.2 1 0 2.55 3.0 3.3 3.2 1 1 2.55 3.1 3.4 3.2 Notes 57. Default setting for BPSNS[1:0] is 00. The above specified thresholds are 50 mV accurate for the indicated edge. A hysteresis is applied to the detectors on the order of 100 mV. BPON is monitoring BP. UVDET, LOBATL and LOBATH are monitoring BPSNS and thresholds are correlated. The UVDET and BPON thresholds are related to the power on/off events as described earlier in this chapter. The LOBATH threshold is used as a weak battery warning. An interrupt LOBATHI is generated when crossing the threshold (dual edge). The LOBATL threshold is used as a low battery detect. An interrupt LOBATLI is generated when dropping below the threshold. The sense bits are coded in line with previous generation parts. Table 29. Power Monitoring Summary BPSNS BPONS LOBATHS LOBATLS < LOBATL 0 0 1 LOBATL-LOBATH 0 0 0 LOBATH-BPON 0 1 0 >BPON 1 1 0 POWER SAVING SYSTEM STANDBY A product may be designed to go into DSM after periods of inactivity, such as if a music player completes a play list and no further activity is detected, or if a gaming interface sits idle for an extended period. Two Standby pins are provided for board level control of timing in and out of such deep sleep modes. When a product is in DSM it may be able to reduce the overall platform current by lowering the switcher output voltage, disabling some regulators, or forcing some GPO low. This can be obtained by SPI configuration of the Standby response of the circuits along with control of the Standby pins. To ensure that shared resources are properly powered when required, the system will only be allowed into Standby when both the STANDBY and the STANDBYSEC are activated. The states of the Standby pins only have influence in On mode. A command to transition to one of the Low-power Off states (User Off or Memory Hold, initiated with USEROFFSPI = 1) has priority over Standby. Note that the Standby pins are programmable for Active High or Active Low polarity, and that decoding of a Standby event will take into account the programmed input polarities associated with each pin. Table 30. Standby Pin and Polarity Control STANDBY (Pin) STANDBYINV (SPI bit) STANDBYSEC (Pin) STANDBYSECINV (SPI bit) STANDBY Control (58) 0 0 x x 0 x x 0 0 0 1 1 x x 0 x x 1 1 0 0 1 0 1 1 MC13892 64 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION OPERATING MODES Table 30. Standby Pin and Polarity Control STANDBY (Pin) STANDBYINV (SPI bit) STANDBYSEC (Pin) STANDBY Control (58) STANDBYSECINV (SPI bit) 0 1 1 0 1 1 0 0 1 1 1 0 1 0 1 Notes 58. STANDBY = 0: System is not in Standby; STANDBY = 1: System is in Standby and Standby programmability is activated. When requesting standby, a programmable delay (STBYDLY) of 0 to 3 clock cycles of the 32 kHz clock is applied before actually going into standby (i.e. before turning off some supplies). No delay is applied when coming out of standby. Table 31. Delay of STANDBY- Initiated Response STBYDLY[1:0] Function (1) 00 No Delay 01 One 32 K period (default) 10 Two 32 K periods 11 Three 32 K periods REGULATOR MODE CONTROL The regulators with embedded pass devices (VDIG, VPLL, VIOHI, VUSB, VUSB2, and VAUDIO) have an adaptive biasing scheme, thus, there are no distinct operating modes such as a Normal mode and a Low-power mode. Therefore, no specific control is required to put these regulators in a Low-power mode. The regulators with external pass devices (VSD, VVIDEO, VGEN1, and VGEN2) can also operate in a Normal and Low-power mode. However, since a load current detection cannot be performed for these regulators, the transition between both modes is not automatic and is controlled by setting the corresponding mode bits for the operational behavior desired. The regulators VGEN3 and VCAM can be configured for using the internal pass device or external pass device as explained in Power Control System. For both configurations, the transition between Normal and Low-power modes is controlled by setting the VxMODE bit for the specific regulator. Therefore, depending on the configuration selected, the automatic Low-power mode is available. The regulators can be disabled and the general purpose outputs can be forced low when going into Standby as described previously. Each regulator and GPO has an associated SPI bit for this. When the bit is not set, STANDBY is of no influence. The actual operating mode of the regulators as a function of STANDBY is not reflected through the SPI. In other words, the SPI will read back what is programmed, not the actual state. Table 32. LDO Regulator Control (External Pass Device LDOs) VxEN VxMODE VxSTBY STANDBY Regulator Vx 0 X X X Off 1 0 0 X On 1 1 0 X Low-power 1 X 1 0 On 1 0 1 1 Off 1 1 1 1 Low-power Notes 59. This table is valid for regulators with an external pass device 60. STANDBY refers to a Standby event as described earlier For regulators with internal pass devices and general outputs, the previous table can be simplified. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 65 FUNCTIONAL DEVICE OPERATION OPERATING MODES Table 33. LDO Regulator Control (Internal Pass Device LDOs) VxEN VxSTBY STANDBY Regulator Vx 0 X X Off 1 0 X On 1 1 0 On 1 1 1 Off Notes 61. This table is valid for regulators with an internal pass device 62. STANDBY refers to a Standby event as described earlier BUCK REGULATORS Operational modes of the Buck regulators can be controlled by direct SPI programming, altered by the state of the STANDBY pins, by direct state machine influence, or by load current magnitude when so configured. Available modes include PWM with No Pulse Skipping (PWM), PWM with Pulse Skipping (PWMPS), Pulse Frequency Mode (PFM), and Off. The transition between the two modes PWMPS and PFM can occur automatically, based on the load current. Therefore, no specific control is required to put the switchers in a Low-power mode. When the buck regulators are not configured in the Auto mode, power savings may be achieved by disabling switchers when not needed, or running them in PFM mode if loading conditions are light enough. SW1, SW2, SW3, and SW4 can be configured for mode switching with STANDBY or autonomously based on load current with adaptive mode control (Auto). Additionally, provisions are made for maintaining PFM operation in USEROFF and MEMHOLD modes to support state retention for faster startup from the Low-power Off modes for Warm Start or Warm Boot. Table 34 summarizes the Buck regulator programmability for Normal and Standby modes. Table 34. Switcher Mode Control for Normal and Standby Operation SWxMODE[3:0] 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 Normal mode(63) Off PWM PWMPS PFM Auto PWM PWM NA Auto PWM PWMPS PWMPS Auto PWM PWMPS PFM Standby Mode(63) Off Off Off Off Off PWM Auto NA Auto PWMPS PWMPS Auto PFM PFM PFM PFM Notes 63. STANDBY defined as logical AND of STANDBY and STANDBYSEC pin In addition to controlling the operating mode in Standby, the voltage setting can be changed. The transition in voltage is handled in a controlled slope manner, see Supplies, for details. Each switcher has an associated set of SPI bits for Standby mode set points. By default the Standby settings are identical to the non-Standby settings, which are initially defined by PUMS programming. The actual operating mode of the switchers as a function of STANDBY pins is not reflected through the SPI. The SPI will read back what is programmed in SWxMODE[3:0], not the actual state that may be altered as described previously. Table 35 and Table 36 show the switcher mode control in the Low-power Off states. Note that a Low-power Off activated SWx should use the Standby set point as programmed by SWxSTBY[4:0]. The activated switcher(s) will maintain settings for mode and voltage until the next startup event. When the respective time slot of the startup sequencer is reached for a given switcher, its mode and voltage settings will be updated the same as if starting out of the Off state (except that switchers active through a Low-power Off mode will not be off when the startup sequencer is started). MC13892 66 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION OPERATING MODES Table 35. Switcher Control In Memory Hold SWxMHMODE Memory Hold Operational Mode (64) 0 Off 1 PFM Notes 64. For Memory Hold mode, an activated SWx should use the Standby set point as programmed by SWxSTBY[4:0]. Table 36. Switcher Control In User Off SWxUOMODE User Off Operational Mode (65) 0 Off 1 PFM Notes 65. For User Off mode, an activated SWx should use the Standby set point as programmed by SWxSTBY[4:0]. POWER GATING SYSTEM The Low-power Off states are provided to allow faster system booting from two pseudo Off conditions: Memory Hold, which keeps the external memory powered for self refresh, and User Off, which keeps the processor powered up for state retention. For reduced current drain in Low-power Off states, parts of the system can benefit from power gating to isolate the minimum essentials for such operational modes. It is also necessary to ensure that the power budget on backed up domains are within the capabilities of switchers in PFM mode. An additional benefit of power gating peripheral loads during system startup is to enable the processor core to complete booting, and begin running software before additional supplies or peripheral devices are powered. This allows system software to bring up the additional supplies and close power gating switches in the most optimum order, to avoid problems with supply sequencing or transient current surges. The power gating switch drivers and integrated control are included for optimizing the system power tree. The power gate drivers could be used for other general power gating as well. The text herein assumes the standard application of PWGT1 for core supply power gating and PWGT2 for Memory Hold power gating. USER OFF POWER GATING User Off configuration maintains PFM mode switchers on both the processor and external memory power domains. PWGTDRV1 is provided for power gating peripheral loads sharing the processor core supply domain(s) SW1, and/or SW2, and/ or SW3. In addition, PWGTDRV2 is provided support to power gate peripheral loads on the SW4 supply domain. In the typical application, SW1, SW2, and SW3 will all be kept active for the processor modules in state retention, and SW4 retained for the external memory in self refresh mode. SW1, SW2, and SW3 power gating FET drive would typically be connected to PWGTDRV1 (for parallel NMOS switches); SW4 power gating FET drive would typically be connected to PWGTDRV2. When Low-power Off mode is activated, the power gate drive circuitry will be disabled, turning off the NMOS power gate switches to isolate the maintained supply domains from any peripheral loading. The power gate switch driver consist of a fully integrated charge pump (~5.0 V) which provides a low-power output to drive the gates of external NMOS switches placed between power sources and peripheral loading. The processor core(s) would typically be connected directly to the SW1 output node so that it can be maintained by SW1, while any circuitry that is not essential for booting or User Off operation is decoupled via the power gate switch. If multiple power domains are to be controlled together, power gating NMOS switches can share the PWGT1 gate drive. However, extra gate capacitance may require additional time for the charge pump gate drive voltage to reach its full value for minimum switch RDS_on. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 67 FUNCTIONAL DEVICE OPERATION OPERATING MODES Figure 13. Power Gating Diagram MEMORY HOLD POWER GATING As with the User Off power gating strategy described previously, Memory Hold power gating is intended to allow isolation of the SW4 power domain, to selected circuitry in Low-power modes while cutting off the switcher domain from other peripheral loads. The only difference is that processor supplies SW1, and/or SW2, and/or SW3, are shut down in Memory Hold, so just the external memory is maintained in self refresh mode. An external NMOS is to be placed between the direct-connected memory supply and any peripheral loading. The PWGTDRV2 pin controls the gate of the external NMOS and is normally pulled up to a charge pumped voltage (~5.0 V). During Memory Hold or User Off, PWGTDRV2 will go low to turn off the NMOS switch and isolate memory on the SW4 power domain. Figure 14. Memory Hold Circuit EXITING FROM LOW-POWER OFF MODES When a Turn On event occurs, any switchers that are active through Low-power Off modes will stay in PFM mode at their Standby voltage set points until the applicable time slot of the startup sequencer. At that point, the respective switcher is updated for the PUMSx defined default state for mode and voltage. Subsequent closing of the power gate switches will be coordinated by software to complete restoration of the full system power tree. MC13892 68 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION OPERATING MODES POWER GATING SPECIFICATIONS AND CONTROL Table 37. Power Gating Characteristics Parameter Condition Min Typ Max Units Output High 5.0 5.40 5.70 V Output Low - - 100 mV Turn-on Time (66), (67) Enable to VOUT = VOUTMIN -250 mV - 50 100 s Turn Off Time Disable to VOUT < 1.0 V - - 1.0 s Average Bias Current t > 500 s after Enable - 1.0 5.0 A PWGTx Input Voltage NMOS drain voltage 0.6 - 2.0 V DC Load Current At PWGTDRVx output - - 100 nA Load Capacitance (66) Used as a condition for the other parameters 0.5 - 1.0 nF Output Voltage VOUT Notes 66. Larger capacitive loading values will lead to longer turn on times exceeding the given limits; smaller values will lead to larger ripple at the output. 67. Input supply is assumed in the range of 3.0 < BP < 4.65 V; lower BP values may extend turn on time, and functionality not supported for BP less than ~2.7 V. A power gate driver pulled low may be thought of as power gating being active since this is the condition where a power source is isolated (or power gated) from its loading on the other side of the switch. The power gate drive outputs are SPI controlled in the active modes as shown in Table 38. Table 38. Power Gate Drive State Control Mode PWGTDRV1 PWGTDRV2 Off Low Low Cold Start Low Low Warm Start Low Low SPI Controlled SPI Controlled Low Low Watchdog, On, User Off Wait User Off, Memory Hold, Internal Memory Hold Power Cut When SPI controlled (Watchdog, On, and User Off Wait states), the PWGTDRVx power gate drive pin states are determined by SPI enable bits PWGTxSPIEN, according to Table 39. Table 39. Power Gating Logic Table PWGTxSPIEN PWGTDRVx 1 Low 0 High Notes 68. Applicable for Watchdog, On and User Off Wait modes only. If PWGT1SPIEN AND PWGT2SPIEN both = 1 then the charge pump is disabled. GENERAL PURPOSE OUTPUTS GPO drivers included can provide useful system level signaling with SPI enabling and programmable Standby control. Key use cases for GPO outputs include battery pack thermistor biasing and enabling of peripheral devices, such as light sensor(s), camera flash, or even supplemental regulators. SPI enabling can be used for coordinating GPOs with ADC conversions for consumption efficiency and desired settling characteristics. Four general purpose outputs are provided, summarized in Table 40 and Table 41 (active high polarities assumed). MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 69 FUNCTIONAL DEVICE OPERATION OPERATING MODES Table 40. GPO Control Bits SPI Bit GPO Control GPOxEN GPOx enable GPOxSTBY GPOx controlled by STANDBY x = 1, 2, 3, or 4 Table 41. GPO Control Scheme GPOxEN GPOxSTBY STANDBY Output GPOx 0 X X Low 1 0 X High 1 1 0 High 1 1 1 Low Notes 69. GPO1 is automatically made active high when a charger is detected, see Battery Interface and Control for more information. The GPO1 output is intended to be used for battery thermistor biasing. For accurate thermistor reading by the ADC, the output resistance of the GPO1 driver is of importance; see ADC Subsystem. Table 42. GPO1 Driver Output Characteristics Parameter GPO1 Output Impedance Condition Min Typ Max Output VCORE Impedance to VCORE 200 - 500 Units Ohm Finally, a muxing option is included to allow GPO4 to be configured for a muxed connection into Channel 7 of the GP ADC. As an application example, for a dual light sensor application, Channel 7 can be toggled between the ADIN7 (ADINSEL7 = 00) and GPO4 (ADINSEL7 = 11) for convenient connectivity and monitoring of two sensors. The GPO4 pin is configured for ADC input mode by default (GPO4ADIN = 1) so that the GPO driver stage is high-impedance at power up. The GPO4 pin can be configured by software for GPO operation with GPO4ADIN = 0. Refer to ADC Subsystem for GP ADC details. MC13892 70 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION SUPPLIES SUPPLIES SUPPLY FLOW The switched mode power supplies and the linear regulators are dimensioned to support a supply flow based upon Figure 15. Charger and USB Cable Interface Accessory Battery Voltage & Current Control Protect Detect Power Audio CC Charge RTC, MEMA/B BP Coincell Peripherals SWBST 5.0V UVBUS PGATE VUSB USB PHY VUSB2 SW1 0.6 to 1.15V Coin Cell Serial Backlight Drivers Vcoredig SW2 0.6 to 1.25V SW3 1.25V SOG Core DVS Domain Internal Processor Memory Peripherals GP Core DVS Domain Alternate hardwired bias option from SW4 Core External Memory IO and Digital SW4 1.8V GPOs PGATE Processor Interfaces Alternate hardwired bias option from external 2.2V switcher Vcore Vcam Viohi Vdig Vpll VVIDEO PNP Camera VAUDIO Vsd PNP PNP Peripherals Core PLLs (Analog) IO, EFUSE GPS Core VGEN3 TV-DAC Audio SD, Tflash PNP Peripherals VGEN1 VGEN2 PNP PNP WLAN, BT MLC NAND Legend System Supplies External Loads Internal Loads Energy Source Figure 15. Supply Distribution While maintaining the performance as specified, the minimum operating voltage for the supply tree is 3.0 V. For lower voltages, the performance may be degraded. Table 43 summarizes the available power supplies. Table 43. Power Tree Summary Supply Purpose (Typical Application) Output Voltage (in V) Load Capability (in mA) SW1 Buck regulators for processor core(s) 0.600-1.375 1050 SW2 Buck regulators for processor SOG, etc. 0.600-1.375; 1.100-1.850 800 SW3 Buck regulators for internal processor memory and peripherals 0.600-1.375; 1.100-1.850 800 SW4 Buck regulators for external memory and peripherals 0.600-1.375; 1.100-1.850 800 SWBST Boost regulator for USB OTG, Tri-color LED drivers 5.0 300 VIOHI IO and Peripheral supply, eFuse support 2.775 100 VPLL Quiet Analog supply (PLL, GPS) 1.2/1.25/1.5/1.8 50 VDIG Low voltage digital (DPLL, GPS) 1.05/1.25/1.65/1.8 50 VSD SD Card, external PNP 1.8/2.0/2.6/2.7/2.8/2.9/3.0/3.15 250 VUSB2 External USB PHY supply 2.4/2.6/2.7/2.775 50 VVIDEO TV DAC supply, external PNP 2.5/2.6/2.7/2.775 350 VAUDIO Audio supply 2.3/2.5/2.775/3.0 150 MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 71 FUNCTIONAL DEVICE OPERATION SUPPLIES Table 43. Power Tree Summary Supply Purpose (Typical Application) Output Voltage (in V) Load Capability (in mA) Camera supply, internal PMOS 2.5/2.6/2.75/3.0 65 Camera supply, external PNP 2.5/2.6/2.75/3.0 250 VGEN1 General peripherals supply #1, external PNP 1.2/1.5/2.775/3.15 200 VGEN2 General peripherals supply #2, external PNP 1.2/1.5/1.6/1.8/2.7/2.8/3.0/3.15 350 General peripherals supply #3, internal PMOS 1.8/2.9 50 General peripherals supply #3, external PNP 1.8/2.9 250 USB Transceiver supply 3.3 100 VCAM VGEN3 VUSB BUCK REGULATOR SUPPLIES Four buck regulators are provided with integrated power switches and synchronous rectification. In a typical application, SW1 and SW2 are used for supplying the application processor core power domains. Split power domains allow independent DVS control for processor power optimization, or to support technologies with a mix of device types with different voltage ratings. SW3 is used for powering internal processor memory as well as low voltage peripheral devices and interfaces which can run at the same voltage level. SW4 is used for powering external memory as well as low voltage peripheral devices and interfaces which can run at the same voltage level. An anticipated platform use case applies SW1 and SW2 to processor power domains that require voltage alignment to allow direct interfacing without bandwidth limiting synchronizers. The buck regulators have to be supplied from the system supply BP, which is drawn from the main battery or the battery charger (when present). Figure 16 shows a high level block diagram of the buck regulators. Figure 16. Buck Regulator Architecture MC13892 72 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION SUPPLIES The Buck regulator topology includes an integrated synchronous rectifier, meaning that the rectifying diode is implemented on the chip as a low ohmic FET. The placement of an external diode is therefore not required, but overall switcher efficiency may benefit from this. The buck regulators permit a 100% duty cycle operation. During normal operation, several power modes are possible depending on the loading. For medium and full loading, synchronous PWM control is the most efficient, while maintaining a constant switching frequency. Two PWM modes are available: the first mode sacrifices low load efficiency for a continuous switching operation (PWM-NPS). The second mode offers better low load efficiency by allowing the absence of switching cycles at low output loading (PWM-PS). This pulse skipping feature improves efficiency by reducing dynamic switching losses by simply switching less often. In its lowest power mode, the switcher can regulate using hysteresis control known as a Pulse Frequency Modulation (PFM) control scheme. The frequency spectrum in this case will be a function of input and output voltage, loading, and the external components. Due to its spectral variance and lighter drive capability, PFM mode is generally reserved for non-active radio modes and Deep Sleep operation. Buck modes of operation are programmable for explicitly defined or load-dependent control (Adaptive). Refer to the Buck regulators section in Power Control System for details. Common control bits available to each buck regulator may be designated with a suffix "x" within this specification, where x stands for 1, 2, 3, or 4 (i.e., SWx = SW1, SW2, SW3, and SW4). The output voltages of the buck regulators are SPI configurable, and two output ranges are available, individually programmed with SWxHI for SW2, SW3, and SW4 bucks, SW1 is limited to only one output range. Presets are available for both the Normal and Standby operation. SW1 and SW2 also include pin controlled DVS operation. When transitioning from one voltage to another, the output voltage slope is controlled in steps of 25 mV per time step (time step as defined for DVS stepping for SW1 and SW2, fixed at 4.0 s for SW3 and SW4). This allows for support of dynamic voltage scaling (DVS) by using SPI driven voltage steps, state machine defined modes, and direct DVSx pin control. When initially activated, switcher outputs will apply controlled stepping to the programmed value. The soft start feature limits the inrush current at startup. A built-in current limiter ensures that during normal operation, the maximum current through the coil is not exceeded. This current limiter can be disabled by setting the SWILIMB bit. Point of Load feedback is intended for minimizing errors due to board level IR drops. SWITCHING FREQUENCY The switchers are driven by a high frequency clock. By default, the PLL generates an effective 3.145728 MHz signal based upon the 32.768 kHz oscillator signal by multiplying it by 96. To reduce spurious radio channels, the PLL can be programmed via PLLX[2:0] to different values as shown in Table 44. Table 44. PLL Multiplication Factor PLLX[2:0] Multiplication Factor Switching Frequency (Hz) 000 84 2 752 512 001 87 2 850 816 010 90 2 949 120 011 93 3 047 424 100 (default) 96 3 145 728 101 99 3 244 032 110 102 3 342 336 111 105 3 440 640 To reduce overall current drain, the PLL is automatically turned off if all switchers are in a PFM mode or turned off, and if the PLL clock signal is not needed elsewhere in the system. The clocking system provides nearly instantaneously, a high frequency clock to the switchers when the switchers are activated or exit the PFM mode for PWM mode. The PLL can be configured for continuous operation by setting the SPI bit PLLEN = 1. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 73 FUNCTIONAL DEVICE OPERATION SUPPLIES Table 45. PLL Main Characteristics Condition (70) Parameter Min Typ Max Units - - 100 ppm PLLEN = 1 - 50 80 A 1 Buck Regulator active - 100 150 A 2 Buck Regulators active - 115 170 A 3 Buck Regulators active - 130 190 A 4 Buck Regulators active - 145 210 A Cold Start - - 700 ns PFM to PWM - - 600 ns Frequency Accuracy Bias Current Start up Time Notes 70. Clock input to PLL is 32.768 kHz Table 46. PLL Control Registers Name R/W Reset Signal PLLEN R/W RESETB PLLX[2:0] R/W RESET Reset State 0 100 Description 1 = Forces PLL on 0 = PLL automatically enabled Selects PLL multiplication factor BUCK REGULATOR CORE Table 47. Buck Regulators (SW1, 2, 3, 4) Output Voltage Programmability Set point SWx[4:0] SWx Output, SWxHI = 0 (Volts) SWx Output (71), SWxHI = 1 (Volts) 0 00000 0.600 1.100 1 00001 0.625 1.125 2 00010 0.650 1.150 3 00011 0.675 1.175 4 00100 0.700 1.200 5 00101 0.725 1.225 6 00110 0.750 1.250 7 00111 0.775 1.275 8 01000 0.800 1.300 9 01001 0.825 1.325 10 01010 0.850 1.350 11 01011 0.875 1.375 12 01100 0.900 1.400 13 01101 0.925 1.425 14 01110 0.950 1.450 15 01111 0.975 1.475 16 10000 1.000 1.500 17 10001 1.025 1.525 18 10010 1.050 1.550 19 10011 1.075 1.575 20 10100 1.100 1.600 21 10101 1.125 1.625 22 10110 1.150 1.650 23 10111 1.175 1.675 24 11000 1.200 1.700 25 11001 1.225 1.725 26 11010 1.250 1.750 27 11011 1.275 1.775 MC13892 74 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION SUPPLIES Table 47. Buck Regulators (SW1, 2, 3, 4) Output Voltage Programmability Set point SWx[4:0] SWx Output, SWxHI = 0 (Volts) SWx Output (71), SWxHI = 1 (Volts) 28 11100 1.300 1.800 29 11101 1.325 1.825 30 11110 1.350 1.850 31 11111 1.375 1.850 71. Output range not available for SW1. SW1 output range is 0.600-1.375, therefore SW1HI = 1 does not apply to SW1. The SW1HI bit should always be set to 0. Since the startup default values of the buck regulators are dependent on the state of the PUMS pin, the SWxHI bit settings will likewise be determined by the PUMS pin. The settings are aligned to the likely application ranges for use cases as given in the Defaults tables in Power Control System. The following tables define the SWxHI bit states after a startup event is completed, but can be reconfigured via the SPI if desired, if an alternate range is needed. Care should be taken when changing SWxHI bit to avoid unintended jumps in the switcher output. The SWxHI setting applies to Normal, Standby, and DVS set points for the corresponding switcher. Table 48. SWxHI States for Power Up Defaults PUMS1 Ground Open VCOREDIG VCORE Ground Open PUMS2 Open Open Open Open Ground Ground SW1HI 0 0 0 0 0 0 SW2HI 0 0 0 0 1 1 SW3HI 0 0 0 0 1 1 SW4HI 1 1 1 1 1 1 Note that the following efficiency curves were measured with the MC13892 in a socket. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 75 FUNCTIONAL DEVICE OPERATION SUPPLIES SW1 PFM mode Efficiency Vout = 0,7 25 V 100% 90% 80% E ffi ciency (%) 70% 60% Vin = 2, 800 V 50% Vin = 3, 600 V 40% Vin = 4, 650 V 30% 20% 10% 0% 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 Il oad (m A) SW2 PFM mode Efficiency Vout = 1.2 50 V 100% 90% 80% E ffi ciency (%) 70% 60% Vin = 2, 800 V 50% Vin = 3, 600 V 40% Vin = 4, 650 V 30% 20% 10% 0% 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 Il oad (m A) SW4 PFM mode Efficiency Vout = 1.8 00 V 100% 90% 80% E ffi ciency (%) 70% 60% Vin = 2, 800 V 50% Vin = 3, 600 V Vin = 4, 650 V 40% 30% 20% 10% 0% 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 Il oad (m A) Figure 17. Buck Regulator PFM Efficiency MC13892 76 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION SUPPLIES S W1 P WM No P ulse Ski pp ing mode Efficien cy V out = 0,725 V S W4 P WM No P ul se S kipp ing mode Efficien cy V out = 1.800 V 100 % 100 % 90 % 90 % 80 % 80 % 70 % 60 % Vin = 3 ,00 0 V 50 % Vin = 3 ,60 0 V 40 % Vin = 4 ,65 0 V Ef fic ien cy (% ) Ef fic ien cy (% ) 70 % 60 % Vin = 3,6 00 V 40 % Vin = 4,6 50 V 30 % 30 % 20 % 20 % 10 % 10 % 0% Vin = 3,0 00 V 50 % 0% 0 10 20 30 40 50 60 70 80 90 10 0 0 50 Ilo a d (m A) 750 8 00 850 9 00 S W2 P WM No P ul se S kipp ing mode Efficien cy V out = 1.250 V 100 % 100 % 90 % 90 % 80 % 80 % 70 % 60 % Vin = 3 ,00 0 V 50 % Vin = 3 ,60 0 V 40 % Vin = 4 ,65 0 V Ef fic ien cy (% ) 70 % Ef fic ien cy (% ) 450 5 00 5 50 60 0 65 0 700 Il oa d (m A) S W2 P WM No P ulse Ski pp ing mode Efficien cy V out = 1.250 V 60 % Vin = 3,0 00 V 50 % Vin = 3,6 00 V 40 % Vin = 4,6 50 V 30 % 30 % 20 % 20 % 10 % 10 % 0% 0% 0 10 20 30 40 50 60 70 80 90 10 0 0 50 Ilo a d (m A) 1 00 1 50 20 0 2 50 30 0 35 0 400 450 5 00 5 50 60 0 65 0 700 750 8 00 850 9 00 Il oa d (m A) S W4 P WM No P ulse Ski pp ing mode Efficien cy V out = 1.800 V S W4 P WM No P ul se S kipp ing mode Efficien cy V out = 1.800 V 100 % 100 % 90 % 90 % 80 % 80 % 70 % 60 % Vin = 3 ,00 0 V 50 % Vin = 3 ,60 0 V Vin = 4 ,65 0 V 40 % Ef fic ien cy (% ) 70 % Ef fic ien cy (% ) 1 00 1 50 20 0 2 50 30 0 35 0 400 60 % Vin = 3,0 00 V Vin = 3,6 00 V 50 % Vin = 4,6 50 V 40 % 30 % 30 % 20 % 20 % 10 % 10 % 0% 0% 0 10 20 30 40 50 60 70 Ilo a d (m A) 80 90 10 0 0 50 1 00 1 50 20 0 2 50 30 0 35 0 400 450 5 00 5 50 60 0 65 0 700 750 8 00 850 9 00 Il oa d (m A) Figure 18. Buck Regulator PWM (No Pulse Skipping) Efficiency MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 77 FUNCTIONAL DEVICE OPERATION SUPPLIES S W1 PWM P ulse Ski ppi ng mo de E ffi ciency Vo ut = 0, 725 V S W1 P WM Pu lse S kip pi ng mo de E ffi ciency Vo ut = 0, 725 V 100 % 100 % 90 % 90 % 80 % 80 % Ef fic ien cy (% ) 60 % Vin = 3 ,00 0 V 50 % Vin = 3 ,60 0 V 40 % Vin = 4 ,65 0 V Ef fic ien cy (% ) 70 % 70 % 60 % Vin = 3,0 00 V 50 % Vin = 3,6 00 V 40 % Vin = 4,6 50 V 30 % 30 % 20 % 20 % 10 % 10 % 0% 0% 0 0 10 20 30 40 50 60 70 80 90 50 1 00 150 200 25 0 300 35 0 4 00 450 50 0 55 0 6 00 650 70 0 7 50 800 85 0 90 0 9 50 10 0 1 05 10 0 0 Ilo a d (m A) S W2 P WM Pu lse S kip pi ng mo de E ffi ciency Vo ut = 1. 250 V S W2 P WM Pu lse S kip pin g m od e E ffici ency V ou t = 1.250 V 100 % 100 % 90 % 90 % 80 % 80 % 70 % 60 % Vin = 3 ,00 0 V 50 % Vin = 3 ,60 0 V 40 % Vin = 4 ,65 0 V Ef fic ien cy (% ) Ef fic ien cy (% ) 70 % 60 % Vin = 3, 000 V 50 % Vin = 3, 600 V 40 % Vin = 4, 650 V 30 % 30 % 20 % 20 % 10 % 10 % 0% 0% 0 10 20 30 40 50 60 70 80 90 10 0 0 50 Ilo a d (m A) 1 00 1 50 20 0 25 0 300 350 4 00 4 50 50 0 55 0 600 650 7 00 7 50 80 0 85 0 900 Ilo a d (m A) S W4 P WM Pu lse S kip pi ng mo de E ffi ciency Vo ut = 1. 800 V S W4 PWM P ulse Ski ppi ng mo de E ffi ciency Vo ut = 1. 800 V 100 % 100 % 90 % 90 % 80 % 80 % 70 % 60 % Vin = 3 ,00 0 V 50 % Vin = 3 ,60 0 V Vin = 4 ,65 0 V 40 % Ef fic ien cy (% ) 70 % Ef fic ien cy (% ) 0 Il oa d (m A) 60 % Vin = 3,0 00 V 50 % Vin = 3,6 00 V 30 % 30 % 20 % 20 % 10 % Vin = 4,6 50 V 40 % 10 % 0% 0% 0 10 20 30 40 50 60 Ilo a d (m A) 70 80 90 10 0 0 50 1 00 1 50 20 0 2 50 30 0 35 0 400 450 5 00 5 50 60 0 65 0 700 750 8 00 850 9 00 Il oa d (m A) Figure 19. Buck Regulator PWM (Pulse Skipping) Efficiency DYNAMIC VOLTAGE SCALING To reduce overall power consumption, processor core voltages can be varied depending on the mode or activity level of the processor. SW1 and SW2 allow for three different set points with controlled transitions to avoid sudden output voltage changes, which could cause logic disruptions on their loads. Preset operating points for SW1 and SW2 can be set up for: * Normal operation: output value selected by SPI bits SWx[4:0]. Voltage transitions initiated by SPI writes to SWx[4:0] are governed by the same DVS stepping rate that is programmed for DVSx pin initiated transitions. * DVS: output can be higher or lower than normal operation for tailoring to application requirements. Configured by SPI bits SWxDVS[4:0] and controlled by a DVSx pin transition. * Standby (Deep Sleep): can be higher or lower than normal operation, but is typically selected to be the lowest state retention voltage of a given process. Set by SPI bits SWxSTBY[4:0] and controlled by a Standby event (STANDBY logically anded with STANDBYSEC). Voltage transitions initiated by Standby are governed by the same DVS stepping that is programmed for DVSx pin initiated transitions. The following tables summarize the set point control and DVS time stepping applied to SW1 and SW2. MC13892 78 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION SUPPLIES Table 49. DVS Control Logic Table for SW1 and SW2 STANDBY (72) DVSx Pin Set Point Selected by 0 0 SWx[4:0] 0 1 SWxDVS[4:0] 1 X SWxSTBY[4:0] Notes 72. STANDBY is the logical anding of STANDBY and STANDBYSEC Table 50. DVS Speed Selection for SW1 and SW2 SWxDVSSPEED[1:0] Function 00 25 mV step each 2.0 s 01 (default) 25 mV step each 4.0 s 10 25 mV step each 8.0 s 11 25 mV step each 16 s Since the switchers have a strong sourcing capability but no active sinking capability, the rising slope is determined by the switcher, but the falling slope can be influenced by the load. Additionally, as the current capability in PFM mode is reduced, controlled DVS transitions in PFM mode could be affected. Critically timed DVS transitions are best assured with PWM mode operation. Note that there is a special mode of DVS control for Switcher Increment / Decrement (SID) operation described later in this chapter. DVS pin controls are not included for SW3 and SW4. However, voltage transitions programmed through the SPI will step in increments of 25 mV per 4.0 s, to allow SPI controlled voltage stepping with SWx[4:0]. Additionally, SW3 and SW4 include Standby mode set point programmability. Figure 20 shows the general behavior for the switchers when initiated with pin controlled DVS, SPI programming or standby control. Figure 20. SW1 Voltage Stepping with Pin Controlled DVS Note that the DVSx input pins are reconfigured for Switcher Increment / Decrement (SID) control mode when SPI bit SIDEN = 1. Refer to the SID description below for further details. SWITCHER INCREMENT / DECREMENT A scheme for incrementing or decrementing the operating set points of SW1 and SW2 is desirable for improved Dynamic Process and Temperature Compensation (DPTC) control in support of fine tuning power domains for the processor supply tree. An increment command will increase the set point voltage by a single 25 mV step. A decrement command will decrease the set point by a single 25 mV step. The transition time for the step will be the same as programmed with SWxDVSSPEED[1:0] for DVS MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 79 FUNCTIONAL DEVICE OPERATION SUPPLIES stepping. If a switcher runs out of programmable range (in either direction), as constrained by programmable stops, then the increment or decrement command shall be ignored. The Switcher Increment / Decrement (SID) function is enabled with SIDEN = 1. This will reassign the function of the DVS1 and DVS2 pins, from the default toggling between Normal and DVS operating modes, to a jog control mode for the switcher which DVSx is assigned. Once enabled, the switcher being controlled will start at the Normal mode set point as programmed with SWx[4:0] and await any jog commands from the processor. The adjustment scheme essentially intercepts the Normal mode set point SPI bits (i.e., but not DVS or Standby programmed set points), and makes any necessary adjustments based on jog up or jog down commands. The modified set point bits are then immediately passed to the switching regulator, which would then do a DVS step in the appropriate direction. The SPI bits containing Normal mode programming are not directly altered. When configured for SID mode, a high pulse on the DVSx pin will indicate one of 3 actions to take, with the decoding as a function of how many contiguous SPI clock falling edges are seen while the DVSx pin is held high. Table 51. SID Control Protocol Number of SPI CLK Falling Edges while DVSx = 1 Function 0 No action. Switcher stays at its presently programmed configuration 1 Jog down. Drive buck regulator output down a single DVS step 2 Jog up. Drive buck regulator output up a single DVS step 3 or more Panic Mode. DVS step the buck regulator output to the Normal mode value as programmed in the SPI register The SID protocol is illustrated by way of example, assuming SIDEN = 1, and that DVS1 is controlling SW1. SW1 starts out at its default value of 1.250 V (SW1 = 11010) and is stepped both up and down via the DVS1 pin. The SPI bits SW1 = 11010 do not change. The set point adjustment takes place in the SID block prior to bit delivery to the switcher's digital control. Starting Value SW1 output DVS Down 1.275 1.250 DVS Down 1.250 1.225 Up DVS1 SPICLK DVS Up 1 Down 2 1 Down 1 SPICLK shut down when not used Figure 21. SID Control Example for Increment & Decrement SID Panic Mode is provided for rapid recovery to the programmed Normal mode output voltage, so the processor can quickly recover to its high performance capability with a minimum of communication latency. In Figure 22, Panic Mode recovery is illustrated as an Increment step, initiated by the detection of the second falling SPI clock edge, followed by a continuation to the programmed SW1[4:0] level (1.250 V in this example), due to the detection of the third contiguous falling edge of SPI clock while DVS1 is held high. MC13892 80 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION SUPPLIES SID Panic Mode Example Starting Value SW1 output DVS step all the way back to 1.250V (SW1[4:0] programmed value = 1.250V) 1.050 Up DVS1 SPICLK DVS Up 1 Panic 2 3 SPICLK shut down when not used Figure 22. SID Control Example for Panic Mode Recovery The system will not respond to a new jog command until it has completed a DVS step that may be in progress. Any missed jog requests will not be stored. For instance, if a switcher is stepping up in voltage with a 25 mV step over a 4.0 s time, response to the DVSx pin for another step will be ignored until the DVS step period has expired. However, the Panic Mode step recovery should respond immediately upon detection of the third SPICLK edge while the corresponding DVSx pin is high, even if the initial decode of the jog up command is ignored, because it came in before the previous step was completed. While in SID mode, programmable stops are used to set limits on how far up and how far down a SID-controlled buck regulator will be allowed to step. The SWxSIDMIN[3:0] and SWxSIDMAX[3:0] bits can be used to ensure that voltage stepping is confined to within the acceptable bounds for a given process technology used for the BB IC. To contain all of the SWx voltage setting bits in single banks, the SWxSIDMIN[3:0] word is shortened to 4-bits, but should be decoded by logic to have an implied leading 0 (i.e., MSB = 0, but is not included in the programmable word). For instance, SW1SIDMIN = 1000 (default value) should be decoded as 01000, which corresponds to 0.800 V (assuming SW1HI = 0). Likewise, the SWxSIDMAX[3:0] word is shortened to 4-bits, but should be decoded by logic to have an implied leading 1 (MSB = 1, but is not included in the programmable word). For instance, SW1SIDMAX = 1010 (default value) should be decoded as 11010, which corresponds to 1.250 V (again, assuming SW1HI = 0). A new SPI write for the active switcher output value with SWx[4:0] should take immediate effect, and this becomes the new baseline from which succeeding SID steps are referenced. The SWxDVS[4:0] value is not considered during SID mode. The system only uses the SWx[4:0] bits and the min/max stops SWxSIDMIN[3:0] and SWxSIDMAX[3:0]. When in SID mode, a STANDBY = 1 event (pin states of STANDBY and STANDBYSEC) will have the "immediate" effect (after any STBYDLY delay has timed out) of changing the set point and mode to those defined for Standby operation. Exiting Standby puts the system back to the normal mode set point with no stored SID adjustments -- the system will recalibrate itself again from the refreshed baseline. BOOST REGULATOR SWBST is a boost switching regulator with a fixed 5.0 V output. It runs at 2/3 of the switcher PLL frequency. SWBST supplies the VUSB regulator for the USB system in OTG mode, and it also supplies the power for the RGB LED's. When SWBST is configured to supply the VBUS pin in OTG mode, the feedback will be switched to sense the UVBUS pin instead of the SWBSTFB pin. Therefore, when driving the VBUS for OTG mode the output of the switcher may rise to 5.75 V to compensate for the voltage drops on the internal switches. Note that the parasitic leakage path for a boost regulator will cause the output voltage SWBSTOUT and SWBSTFB to sit at a Schottky drop below the battery voltage whenever SWBST is disabled. The switching NMOS transistor is integrated on-chip. An external fly back Schottky diode, inductor and capacitor are required. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 81 FUNCTIONAL DEVICE OPERATION SUPPLIES Figure 23. Boost Regulator Architecture Enabling of SWBST is accomplished through the SWBSTEN SPI control bit. Table 52. Switch Mode Supply SWBST Control Function Summary Parameter Value SWBSTEN Function 0 SWBST OFF 1 SWBST ON 5V Boost Effic ie ncy (Vin = 3 .6 V, Vou t = 5V) Efficiency (%) 100.00 95.00 90.00 85.00 80.00 0 1 00 2 00 300 Boost Load Current (mA) Figure 24. Boost Regulator Efficiency LINEAR REGULATORS This section describes the linear regulators provided. For convenience, these regulators are named to indicate their typical or possible applications, but the supplies are not limited to these uses and may be applied to any loads within the specified regulator capabilities. A low-power standby mode controlled by STANDBY is provided in which the bias current is aggressively reduced. This mode is useful for deep sleep operation where certain supplies cannot be disabled, but active regulation can be tolerated with lesser parametric requirements. The output drive capability and performance are limited in this mode. Refer to STANDBY Event Definition and Control in Power Control System for more details. Some dedicated regulators are covered in their related chapters rather than in the Supplies chapter (i.e., the VUSB and VUSB2 supplies are included in Connectivity). Apart from the integrated linear regulators, there are also GPO output pins provided to enable and disable discrete regulators or functional blocks, or to use as a general purpose output for any system need. For example, one application may be to enable a battery pack thermistor bias in synchronization with timed ADC conversions. MC13892 82 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION SUPPLIES All regulators use the main bandgap as the reference. The main bandgap is bypassed with a capacitor at REFCORE. The bandgap and the rest of the core circuitry is supplied from VCORE. The performance of the regulators is directly dependent on the performance of VCOREDIG and the bandgap. No external DC loading is allowed on VCOREDIG or REFCORE. VCOREDIG is kept powered as long as there is a valid supply and/or coin cell. Table 53 captures the main characteristics of the core circuitry. Table 53. Core Specifications Reference VCOREDIG (Digital core supply) VCORE (Analog core supply) REFCORE (Bandgap / Regulator Reference) Parameter Target Output voltage in ON mode (73),(74) 1.5 V Output voltage in Off mode(74) 1.2 V Bypass Capacitor 2.2 F typ (0.65 F derated) Output voltage in ON mode (73),(74) 2.775 V Output voltage in Off mode (74) 0.0 V Bypass Capacitor 2.2 F typ (0.65 F derated) Output voltage (73) 1.20 V Absolute Accuracy 0.50% Temperature Drift 0.25% Bypass Capacitor 100 nF typ (65 nF derated) Notes 73. 3.0 V < BP < 4.65 V, no external loading on VCOREDIG, VCORE, or REFCORE. Extended operation down to UVDET, but no system malfunction. 74. The core is in On mode when charging or when the state machine of the IC is not in the Off mode nor in the power cut mode. Otherwise, the core is in Off mode. REGULATORS GENERAL CHARACTERISTICS * * * * * * * * * * * The following applies to all linear regulators unless otherwise specified. Specifications are for an ambient temperature of -40 to +85 C. Advised bypass capacitor is the MurataTM GRM155R60G225ME15 which comes in a 0402 case. In general, parametric performance specifications assume the use of low ESR X5R ceramic capacitors with 20% accuracy and 15% temperature spread, for a worst case stack up of 35% from the nominal value. Use of other types with wider temperature variation may require a larger room temperature nominal capacitance value to meet performance specs over temperature. In addition, capacitor derating as a function of DC bias voltage requires special attention. Finally, minimum bypass capacitor guidelines are provided for stability and transient performance. Larger values may be applied; performance metrics may be altered and generally improved, but should be confirmed in system applications. Regulators which require a minimum output capacitor ESR (those with external PNPs) can avoid an external resistor if ESR is assured with capacitor specifications, or board level trace resistance. The output voltage tolerance specified for each of the linear regulators include process variation, temperature range, static line regulation, and static load regulation. The PSRR of the regulators is measured with the perturbed signal at the input of the regulator. The power management IC is supplied separately from the input of the regulator and does not contain the perturbed signal. During measurements care must be taken not to reach the drop out of the regulator under test. In the Low-power mode the output performance is degraded. Only those parameters listed in the Low-power mode section are guaranteed. In this mode, the output current is limited to much lower currents than in the Active mode. Regulator performance is degraded in the extended input voltage range. This means that the supply still behaves as a regulator and will try to hold up the output voltage by turning the pass device fully on. As a result, the bias current will increase and all performance parameters will be heavily degraded, such as PSRR and load regulation. Note that in some cases, the minimum operating range specifications may be conflicting due to numerous set point and biasing options, as well as the potential to run BP into one of the software or hardware shutdown thresholds. The specifications are general guidelines which should be interpreted with some care. When a regulator gets disabled, the output will be pulled towards ground by an internal pull-down. The pull-down is also activated when RESETB goes low. 32 kHz spur levels are specified for fully loaded conditions. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 83 FUNCTIONAL DEVICE OPERATION SUPPLIES * Short-circuit protection (SCP) is included on certain LDOs (see the SCP section later in this chapter). Exceeding the SCP threshold will disable the regulator and generate a system interrupt. The output voltage will not sag below the specified voltage for the rated current being drawn. For the lower current LDOs without SCP, they are less accessible to the user environment and essentially self-limiting. * The power tree of a given application must be scrubbed for critical use cases to ensure consistency and robustness in the power strategy. TRANSIENT RESPONSE WAVEFORMS The transient load and line response are specified with the waveforms as depicted in Figure 25. Note that the transient load response refers to the overshoot only, excluding the DC shift itself. The transient line response refers to the sum of both overshoot and DC shift. This is also valid for the mode transition response. Figure 25. Transient Waveforms SHORT-CIRCUIT PROTECTION The higher current LDOs and those most accessible in product applications include short-circuit detection and protection (VVIDEO, VAUDIO, VCAM, VSD, VGEN1, VGEN2, and VGEN3). The short-circuit protection (SCP) system includes debounced fault condition detection, regulator shutdown, and processor interrupt generation, to contain failures and minimize chance of MC13892 84 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION SUPPLIES product damage. If a short-circuit condition is detected, the LDO will be disabled by resetting its VxEN bit while at the same time an interrupt SCPI will be generated to flag the fault to the system processor. The SCPI interrupt is maskable through the SCPM mask bit. The SCP feature is enabled by setting the REGSCPEN bit. If this bit is not set, then not only is no interrupt generated, but also the regulators will not automatically be disabled upon a short-circuit detection. However, the built-in current limiter will continue to limit the output current of the regulator. Note that by default, the REGSCPEN bit is not set, so at startup none of the regulators that are in an overload condition will be disabled VAUDIO AND VVIDEO SUPPLIES The primary applications of these power supplies are for audio, and TV-DAC. However these supplies could also be used for other peripherals if one of these functions is not required. Low-power modes and programmable Standby options can be used to optimize power efficiency during Deep Sleep modes. An external PNP is utilized for VVIDEO to avoid excess on-chip power dissipation at high loads, and large differential between BP and output settings. For stability reasons a small minimum ESR may be required. In the Low-power mode for VVIDEO an internal bypass path is used instead of the external PNP. External PNP devices are always to be connected to the BP line in the application. The recommended PNP device is the ON Semiconductor NSS12100XV6T1G which is capable of handling up to 250 mW of continuous dissipation at minimum footprint and 75 C of ambient. For use cases where up to 500mW of dissipation is required, the recommended PNP device is the ON Semiconductor NSS12100UW3TCG. For stability reasons a small minimum ESR may be required. VAUDIO is implemented with an integrated PMOS pass FET and has a dedicated input supply pin VINAUDIO. The following tables contain the specifications for the VVIDEO, VAUDIO. Table 54. VVIDEO and VAUDIO Voltage Control Parameter VVIDEO VAUDIO Value Function ILoad max 00 Output = 2.700 V 250 mA / 350 mA 01 Output = 2.775 V 250 mA / 350 mA 10 Output = 2.500 V 250 mA / 350 mA 11 Output = 2.600 V 250 mA / 350 mA 00 Output = 2.300 V 150 mA 01 Output = 2.500 V 150 mA 10 Output = 2.775 V 150 mA 11 Output = 3.000 V 150 mA LOW VOLTAGE SUPPLIES VDIG and VPLL are provided for isolated biasing of the Baseband system PLLs for clock generation in support of protocol and peripheral needs. Depending on the lineup and power requirements, these supplies may be considered for sharing with other loads, but noise injection must be avoided and filtering added if necessary, to ensure suitable PLL performance. The VDIG and VPLL regulators have a dedicated input supply pin: VINDIG for the VDIG regulator, and VINPLL for the VPLL regulator. VINDIG and VINPLL can be connected to either BP or a 1.8V switched mode power supply rail, such as from SW4 for the two lower set points of each regulator VPLL[1:0] and VDIG[1:0] = [00], [01]. In addition, when the two upper set points are used VPLL[1:0] and VDIG[1:0] = [10], [11], the inputs (VINDIG and VINPLL) can be connected to either BP of a 2.2 V nominal external switched mode power supply rail to improve power dissipation. Table 55. VPLL and VDIG Voltage Control Parameter VPLL[1:0] VDIG[1:0] Value Function ILoad max Input Supply 00 output = 1.2 V 50 mA BP or 1.8 V 01 output = 1.25 V 50 mA BP or 1.8 V 10 output = 1.5 V 50 mA BP or External Switcher 11 output = 1.8 V 50 mA BP or External Switcher 00 output = 1.05 V 50 mA BP or 1.8 V 01 output = 1.25 V 50 mA BP or 1.8 V 10 output = 1.65 V 50 mA BP or External Switcher 11 output = 1.8 V 50 mA BP or External Switcher MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 85 FUNCTIONAL DEVICE OPERATION SUPPLIES PERIPHERAL INTERFACING IC interfaces in the lineups generally fall in two categories: low voltage IO primarily associated with the AP IC and certain peripherals at SPIVCC level (powered from SW4), and a higher voltage interface level associated with other peripherals not compatible with the 1.8 V SPIVCC. VIOHI is provided at a fixed 2.775 V level for such interfaces, and may also be applied to other system needs within the guidelines of the regulator specifications. The input VINIOHI is not only used by the VIOHI regulator, but also by other blocks, therefore it should always be connected to BP, even if the VIOHI regulator is not used by the system. VIOHI has an internal PMOS pass FET which will support loads up to 100 mA. CAMERA The camera module is supplied by the regulator VCAM. This allows powering the entire module independent of the rest of other parts of the system, as well as to select from a number of VCAM output levels for camera vendor flexibility. In applications with a dual camera, it is anticipated that only one of the two cameras is active at a time, allowing the VCAM supply to be shared between them. VCAM has an internal PMOS pass FET which will support up to 2.0 Mpixel Camera modules (<65 mA). To support higher resolution cameras, an external PNP is provided. The external PNP configuration is offered to avoid excess on-chip power dissipation at high loads, and large differential between BP and output settings. For lower current requirements, an integrated PMOS pass FET is included. The input pin for the integrated PMOS option is shared with the base current drive pin for the PNP option. The external PNP configuration must be committed as a hardwired board level implementation, while the operating mode is selected through the VCAMCONFIG bit after startup. The VCAM is not automatically enabled during the power up sequence, allowing software to properly set the VCAMCONFIG bit before the regulator is activated. The recommended PNP device is the ON Semiconductor NSS12100XV6T1G which is capable of handling up to 250 mW of continuous dissipation at a minimum footprint and 75 C of ambient. For use cases where up to 500 mW of dissipation is required, the recommended PNP device is the ON Semiconductor NSS12100UW3TCG. For stability reasons a small minimum ESR may be required. The input VINCAM should always be connected to BP, even if the VCAM regulator is not used by the system. Table 56. VCAM Voltage Control ILoad max Parameter VCAM[1:0] Value Output Voltage VCAMCONFIG=0 Internal Pass FET VCAMCONFIG=1 External PNP 00 2.5 V 65 mA 250 mA 01 2.6 V 65 mA 250 mA 10 2.75 V 65 mA 250 mA 11 3.00 V 65 mA 250 mA MULTI-MEDIA CARD SUPPLY This supply domain is generally intended for user accessible multi-media cards, such as Micro-SD (TransFlash), RS-MMC, and the like. An external PNP is utilized for this LDO to avoid excess on-chip power dissipation at high loads and large differential between BP and output settings. The external PNP device is always connected to the BP line in the application. VSD may also be applied to other system needs within the guidelines of the regulator specifications. The recommended PNP device is the ON Semiconductor NSS12100XV6T1G, which is capable of handling up to 250 mW of continuous dissipation at a minimum footprint and 75 C of ambient. For use cases where up to 500 mW of dissipation is required, the recommended PNP device is the ON Semiconductor NSS12100UW3TCG. For stability reasons a small minimum ESR may be required. At the 1.8 V set point, the VSD regulator can be powered from an external buck regulator (2.2 V typ) for an efficiency advantage and reduced power dissipation in the pass devices. MC13892 86 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION SUPPLIES Table 57. VSD Voltage Control Parameter Value VSD[2:0] Output Voltage ILoad max Input Supply 000 1.80 V 250 mA BP or External Switcher 001 2.00 V 250 mA BP 010 2.60 V 250 mA BP 011 2.70 V 250 mA BP 100 2.80 V 250 mA BP 101 2.90 V 250 mA BP 110 3.00 V 250 mA BP 111 3.15 V 250 mA BP GEN1, GEN2, AND GEN3 REGULATORS General purpose LDOs VGEN1, VGEN2, and VGEN3 are provided for expansion of the power tree to support peripheral devices, which could include WLAN, BT, GPS, or other functional modules. All the regulators include programmable set points for system flexibility. At the 1.2 V and 1.5 V set points, both VGEN1 and VGEN2 can be powered from an external buck regulator (2.2 V typ) for an efficiency advantage, and reduced power dissipation in the pass devices. (Note that a connection to BP or the external buck regulator as the input to the regulators is a hardwired board level commitment, and not changed on-the-fly). Table 58. VGEN1 Control Register Bit Assignments Parameter VGEN1[1:0] Value Function ILoad max(75) Input Supply 00 output = 1.20 V 200 mA BP or external switcher 01 output = 1.50 V 200 mA BP or external switcher 10 output = 2.775 V 200 mA BP 11 output = 3.15 V 200 mA BP Notes 75. The max load given for VGEN1MODE = 0 and must take into account the capabilities of the external pass device and operating conditions, to manage its power dissipation. Load capability is 3.0 mA for VGEN1MODE = 1. Table 59. VGEN2 Control Register Bit Assignments Parameter VGEN2[2:0] Value Function ILoad max (76) Input Supply 000 output = 1.20 V 350 mA BP or external switcher 001 output = 1.50 V 350 mA BP or external switcher 010 output = 1.60 V 350 mA BP 011 output = 1.80 V 350 mA BP 100 output = 2.70 V 350 mA BP 101 output = 2.80 V 350 mA BP 110 output = 3.00 V 350 mA BP 111 output = 3.15 V 350 mA BP Notes 76. The max load is given for as VGEN2MODE = 0, and must take into account the capabilities of the external pass device and operating conditions to manage its power dissipation. Load capability is 3.0 mA for VGEN2MODE = 1. VGEN3 has an internal PMOS pass FET which will support loads up to 50 mA. For higher current capability, drive for an external PNP is provided. The external PNP configuration is offered to avoid excess on-chip power dissipation at high loads, and large differential between BP and output settings. The input pin for the integrated PMOS option is shared with the base current drive pin for the PNP option. The external PNP configuration must be committed as a hardwired board level implementation, while the operating mode is selected through the VGEN3CONFIG bit after startup. The VGEN3 is not automatically enabled during the power up sequence, allowing software to properly set the VGEN3CONFIG bit before the regulator is activated. The recommended PNP device is the ON Semiconductor NSS12100XV6T1G, which is capable of handling up to 250 mW of MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 87 FUNCTIONAL DEVICE OPERATION SUPPLIES continuous dissipation at minimum footprint and 75 C of ambient. For use cases where up to 500 mW of dissipation is required, the recommended PNP device is the ON Semiconductor NSS12100UW3TCG. For stability reasons a small minimum ESR may be required. A short circuit condition will shut down the VGEN3 regulator and generate an interrupt for SCPI. Table 60. VGEN3 Voltage Control ILoad max VGEN3 bit Output Voltage VGEN3CONFIG = 0 Internal Pass FET VGEN3CONFIG = 1 External PNP 0 1.80 V 50 mA 200 mA 1 2.90 V 50 mA 200 mA MC13892 88 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION BATTERY INTERFACE AND CONTROL BATTERY INTERFACE AND CONTROL The battery management interface is optimized for applications with a single charger connector to which a standard wall charger or a USB host can be connected. It can also support dead battery operation and unregulated chargers. CHARGE PATH CHARGER LINE UP The charge path is depicted in the following diagram. Figure 26. Charge Path Block Diagram Transistors M1 and M2 control the charge current and provide voltage regulation. The latter is used as the top off change voltage, and as the regulated supply voltage to the application in case of a dead battery operation. In order to support dead battery operation, a so called "serial path" charging configuration including M3 needs to be used. Then in case of a dead battery, the transistor M3 is made non-conducting and the internal trickle charge current charges the battery. If the battery is sufficiently charged, the transistor M3 is made conducting which connects the battery to the application just like during normal operation without a charger. In so called single path charging, M3 is replaced by a short and the pin BATTFET must be floating. Dead battery operation is not supported in this case. Transistors M1 and M2 become non-conducting if the charger voltage is too high. The VBUS must be shorted to CHRGRAW in cases where the wall charger and VBUS voltages are contained on a common pin. A current can be supplied from the battery to an accessory with all transistors M1, M2, and M3 conducting, by enabling the reverse supply mode. An unregulated wall charger configuration can be built, in which case CHRGSE1B must be pulled low. The battery current monitoring resistor R1 and the charge LED indicator are optional. More detail on the battery current monitoring can be found in ADC Subsystem. The preferred devices for M1 and M2 are FairchildTM FDZ193P, due to their small package outline and thermal characteristics. The preferred device for M3 is the On Semiconductor NTHS2101P for its low RDSON and small footprint. CHARGER SIGNALS The charger uses a number of thresholds for proper operation and will also signal various events to the processor through interrupts. Table 61 summarizes the main signals given, including the control bits. For details see the related sections in this chapter and the SPI bit summary in SPI Bitmap. Table 61. Main Control Bit Signals Name Description Control Bits VCHRG[2:0] Charger regulator voltage setting ICHRG[3:0] Charger regulator current setting TREN Internal trickle charger enabling MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 89 FUNCTIONAL DEVICE OPERATION BATTERY INTERFACE AND CONTROL Table 61. Main Control Bit Signals Name Description THCHKB Battery thermistor check disable FETOVRD, FETCTRL SPI control over BATTFET pin (M3) FETOVRD: 0 = BATTFET output are controlled by hardware 1 = BATTFET controlled by the state of the FETCTRL bit FETOCTRL: 0 = BATTFET is driven high if FETOVRD is set 1 = BATTFET is driven low if FETOVRD is set RVRSMODE Reverse mode enabling 0 = Reverse mode disabled 1 = Reverse mode enabled PLIM[1:0], PLIMDIS Power limiter setting and disabling PLIMDIS: 0 = Power limiter enabled 1 = Power limiter disabled CHRGLEDEN Charge LED indicator enabling 0 = CHRGLED disabled 1 = CHRGLED enabled CHGRESTART Charger state machine restart CHGAUTOB Selects between standalone or software controlled charging operation 0 = Standalone charging 1 = Software controlled charging CHGAUTOVIB Allows for SPI control over-voltage and current settings in standalone charging mode CYCLB Controls charging resume behavior 0 = Enables cycling 1 = Disables cycling Interrupt and Status bits CHGDETI Charger attach CHGFAULTI CHRGRAW over-voltage, excessive power dissipation, timeout, battery out of temperature range CHGFAULTS[1:0] Charger fault mode sense bits CHGENS Charger enable sense bit USBOVI USB over-voltage CHGSHORTI Short-circuit detection in reverse mode CHGREVI Charger path reverse current, detection based on CHGCURR threshold CHGCURRI Charge current threshold, detection based on CHGCURR threshold CCCVI Charger path regulation mode, detection based on BATTCYCL threshold CHRGSE1BI Wall Charger Detect CHRGSE1BS CHRSE1B pin sense CHRGSSS Charger configuration sense, serial versus single. A logic 1 indicates a serial path. Thresholds CHGCURR CHRGISNS-BPSNS at 35 mA flowing into phone, used for end of charge detection, charger removal and charge current reversal BATTMIN BATT at 3.0 V, used to increase charge current (40/80 mA and 80/560 mA), detect a dead battery insertion while charging BPON BP at 3.2 V, used to allow turn on when charging from USB, closes M3 when in serial path BATTON BATT at 3.4 V, used to allow turn on when charging from USB, closes M3 when in serial path BATTCYCL BPSNS at 98% of charger voltage setting, used to restart charging, used by CCCVI MC13892 90 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION BATTERY INTERFACE AND CONTROL BUILDING BLOCKS AND FUNCTIONS The battery management interface consists of several building blocks and functions as depicted in the block diagram shown in the previous paragraph. These building blocks and functions are described below while the charger operation is described in the next section. CHARGE PATH REGULATOR The M1 and M2 are permanently used as a combined pass device for a super regulator, with a programmable output voltage and programmable current limit. The voltage loop consists of M1, M2, and an amplifier with voltage feedback taken from the BPSNS pin. The value of the sense resistor is of no influence on the output voltage. The output voltage is programmable by SPI through VCHRG[2:0] bits. Table 62. Charge Path Regulator Voltage Settings VCHRG[2:0] Charge Regulator Output Voltage (V) 000 3.800 001 4.100 010 4.150 011 (default) 4.200 100 4.250 101 4.300 110 4.375 111 4.450 The current loop is composed of the M1 and M2 as control elements, the external sense resistor, a programmable current limit, and an amplifier. The control loop will regulate the voltage drop over the external resistor. The value of the external resistor therefore is of influence on the charge current. The charge current is programmable by SPI through ICHRG[3:0] bits. Each setting corresponds to a common use case. Software controlled pulsed charging can be obtained by programming the current periodically to zero. Table 63. Charge Path Regulator Current Limit Settings Charge Regulator ICHRG[3:0] Current Limit (mA) Specific Use Case 0000 0.0 Off 0001 80 Standalone Charging Default for precharging, USB charging, and LPB 0010 240 0011 320 0100 400 0101 480 0110 560 0111 640 1000 720 1001 800 1010 880 Advised setting for USB charging with PHY active Standalone Charging Default 1011 960 1100 1040 1101 1200 High Current Charger 1110 1600 High Current Charger 1111 Fully On - M3 Open Externally Powered MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 91 FUNCTIONAL DEVICE OPERATION BATTERY INTERFACE AND CONTROL Table 64. Charge Path Regulator Characteristics Parameter Condition Typ Max BATTMIN - 5.6 V - - 0.35 % Charge current 1.0 to 100 mA -1.5 - 1.5 % Charge current > 100 mA and above -3.0 - 1.5 % ICHRG[3:0] =0 001 68 80 92 mA ICHRG[3:0] = 0100 360 400 440 mA ICHRG[3:0] = 0110 500 560 620 mA All other settings - - 15 % Unloaded - - 2.0 % CHRGRAW (78) - 2.2 - F 10 - 4.7 F - - 3.0 m Input Operating Voltage CHRGRAW Output voltage trimming accuracy VCHRG[2:0] = 011 Charge current 50 mA at T = 25 C Output Voltage Spread Current Limit Tolerance(77) Start-up Overshoot Min Units VCHRG[2 :0] = 011, 1xx Configuration Input Capacitance Load Capacitor BPSNS Cable Length (79) (78) Notes 77. Excludes spread and tolerances due to board routing and 100 mOhm sense resistor tolerances. 78. An additional derating of 35% is allowed. 79. This condition applies when using an external charger with a 3.0 m long cable. OVER-VOLTAGE PROTECTION In order to protect the application, the voltage at the CHRGRAW pin is monitored. When crossing the threshold, the charge path regulator will be turned off immediately, by opening M1 and M2, while M3 gets closed. When the over-voltage condition disappears for longer than the debounce time, charging will resume and previously programmed SPI settings will be reloaded. An interrupt CHGFAULTI is generated with associated CHGFAULTM mask bit with the CHGFAULTS[1:0] bits set to 01. In order to ensure immediate protection, the control of M1, M2, and M3 occurs real-time, so asynchronously to the charger state machine. As a result, for over-voltage conditions of up to 30 s, the charger state machine may not always end up in the over-voltage fault state, and therefore an interrupt may not always be generated. Table 65. Charger Over-voltage Protection Characteristics Parameter Condition Min Typ Max Units Over-voltage Comparator High Voltage Threshold High to Low, Low to High 16 - 20 V Over-voltage Comparator Debounce Time High to Low - 10 - ms The VBUS pin is also protected against over-voltages. This will occur at much lower levels for CHRGRAW. When a VBUS over-voltage is detected the internal circuitry of the USB block is disconnected. A USBOVI is generated in this case. For more details see Connectivity. When the maximum voltage of the IC is exceeded, damage will occur to the IC and the state of M1 and M2 cannot be guaranteed. If the user wants to protect against these failure conditions, additional protection will be required. MC13892 92 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION BATTERY INTERFACE AND CONTROL POWER DISSIPATION Since the charge path operates in a linear fashion, the dissipation can be significant and care must be taken to ensure that the external pass FETs M1 and M2 are not over dissipating when charging. By default, the charge system will protect against this by a built-in power limitation circuit. This circuit will monitor the voltage drop between CHRGRAW and CHRGISNS, and the current through the external sense resistor connected between CHRGISNS and BPSNS. When required,.a duty cycle is applied to the M1 and M2 drivers and thus the charge current, in order to stay within the power budget. At the same time M3 is forced to conduct to keep the application powered. In case of excessive supply conditions, the power limiter minimum duty cycle may not be sufficiently small to maintain the actual power dissipation within budget. In that case, the charge path will be disabled and the CHGFAULTI interrupt generated with the CHGFAULTS[1:0] bits set to 01. The power budget can be programmed by SPI through the PLIM[1:0] bits. The power dissipation limiter can be disabled by setting the PLIMDIS bit. In this case, it is advised to use close software control to estimate the dissipated power in the external pass FETs. The power limiter is automatically disabled in serial path factory mode and in reverse mode. Since a charger attachment can be a Turn-on event when a product is initially in the Off state, any non-default settings that are intended for PLIM[1:0] and PLIMDIS, should be programmed early in the configuration sequence, to ensure proper supply conditions adapted to the application. To avoid any false detection during power up, the power limiter output is blanked at the start of the charge cycle. As a safety precaution though, the power dissipation is monitored and the desired duty cycle is estimated. When this estimated duty cycle falls below the power limiter minimum duty cycle, the charger circuit will be disabled. Table 66. Charger Power Dissipation Limiter Control PLIM[1:0] Power Limit (mW) 00 (default) 600 01 800 10 1000 11 1200 Table 67. Charger Power Dissipation Limiter Characteristics Parameter Power Limiter Accuracy Condition Min Typ Max - - 15 % - 500 - ms - 1500 - ms - 10 - % Up to 2x the power set by PLIM[1:0] Power Limiter Control Period Power Limiter Blanking Period Upon charging enabling Power Limiter Minimum Duty Cycle Units REVERSE SUPPLY MODE The battery voltage can be applied to an external accessory via the charge path, by setting the RVRSMODE bit high. The current through the accessory supply path is monitored via the charge path sense resistor R2, and can be read out via the ADC. The accessory supply path is disabled and an interrupt CHGSHORTI is generated when the slow or fast threshold is crossed. The reverse path is disabled when a current reversal occurs and an interrupt CHREVI is generated. Table 68. Accessory Supply Main Characteristics Parameter Condition Typ Max Units 500 - - mA Slow Threshold Debounce Time - 1.0 - ms Short-circuit Current Fast Threshold - - 1840 mA - 100 - s - CHGCURR - mA Short-circuit Current Slow Threshold Fast Threshold Debounce Time Current Reversal Threshold Current from Accessory Min INTERNAL TRICKLE CHARGE CURRENT SOURCE An internal current source between BP and BATTISNS provides small currents to the battery in cases of trickle charging a dead battery. As can be seen under the description of the standalone charging, this source is activated by the charger state machine, and its current level is selected based on the battery voltage. The source can also be enabled in software controlled charging mode by setting the TREN bit. This source cannot be used in single path configurations because in that case, BATTISNS and BP are shorted on the board. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 93 FUNCTIONAL DEVICE OPERATION BATTERY INTERFACE AND CONTROL Table 69. Internal Trickle Charger Control BATT Trickle Charge Current (mA) 0 < BATT < BATTMIN 40 BATTMIN < BATT < BATTON 80 Table 70. Internal Trickle Charger Characteristics Parameter Condition Trickle Charge Current Accuracy Operating Voltage Extended Operating Range (80) Min Typ Max Units - - 30 % BATTISNS 0.0 - - V BP-BATTISNS 1.0 - - V BP-BATTISNS 0.3 - - V Notes 80. The effective trickle current may be significantly reduced CHARGER DETECTION AND COMPARATORS The charger detection is based on three comparators. The "charger valid" monitors CHRGRAW, the "charger presence" that monitors the voltage drop between CHRGRAW and BPSNS, and the "CHGCURR" comparator that monitors the current through the sense resistor connected between CHRGISNS and BPSNS. A charger insertion is detected based on the charger presence comparator and the "charger valid" comparator both going high. For all but the lowest current setting, a charger removal is detected based on both the "charger presence" comparator going low and the charger current falling below CHGCURR. In addition, for the lowest current settings or if not charging, the "charger valid" comparator going low is an additional cause for charger removal detection. The table below summarizes the charger detection logic. Table 71. Charger Detection Setting ICHRG[3:0] 0000, 0001 Other Settings Charger Valid Comparator Charger Presence Comparator CHGCURR Comparator Charger Detected 0 X X 1 0 X No No 1 1 X Yes X 0 0 No X 1 X Yes X X 1 Yes In addition to the aforementioned comparators, three more comparators play a role in battery charging. These comparators are "BATTMIN", which monitors BATT for the safe charging battery voltage, "BATTON", which monitors BATT for the safe operating battery voltage, and "BATTCYCL", which monitors BPSNS for the constant current to constant voltage transition. The BATTMIN and BATTON comparators have a normal and a long (slow) debounced output. The slow output is used in some places in the charger flow to provide enough time to the battery protection circuit to reconnect the battery cell. Table 72. Charger Detectors Main Characteristics Min Typ Max Units BATTMIN Threshold Parameter At BATT Condition 2.9 - 3.1 Volts BATTON Threshold At BATT 3.3 - 3.5 Volts BATTCYCL Threshold At BPSNS relative to VCHRG[2:0] - 98 - % Charger Presence CHRGRAW-BPSNS 10 - 50 mV Charger Valid CHRGRAW - 3.8 - V CHGCURR Threshold CHRGISNS-BPSNS, current from charger 10 - 50 mA MC13892 94 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION BATTERY INTERFACE AND CONTROL Table 72. Charger Detectors Main Characteristics (continued) Parameter Condition Debounce Period Min Typ Max Units BATTMIN, BATTON rising edge (normal - 32 - ms BATTMIN, BATTON rising edge (slow) - 1.0 - s BATTMIN falling edge (slow) - 1.0 - s BATTMIN falling edge (fast) - 1.0 - s BATTCYCL dual edge - 100 - ms CHGCURR - 1.0 - ms Charger Detect dual edge - 100 - ms Crossing the thresholds BATTCYCL and CHGCURR will generate the interrupts CCCVI and CHGCURRI respectively. These interrupts can be used as a simple way to implement a three-bar battery meter. BATTERY THERMISTOR CHECK CIRCUITRY A battery pack may be equipped with a thermistor, which value decreases over temperature (NTC). The relationship between temperature T (in Kelvin) and the thermistor value (RT) is well characterized and can be described as RT = R0*e^(B*(1/T-1/T0), with T0 being room temperature, R0 the thermistor value at T0 and B being the so called B-factor which indicates the slope of the thermistor over temperature. In order to read out the thermistor value, it is biased from GPO1 through a pull-up resistor RPU. See also the ADC chapter. The battery thermistor check circuit compares the fraction of GPO1 at ADIN5 with two preset thresholds, which correspond to 0 and 45 C, see Table 73. Charging is generally allowed when the thermistor is within the range, see next section for details. Table 73. Battery Thermistor Check Main Characteristics Temperature Threshold Voltage at ADIN5 Corresponding Resistor Values Corresponding Temperature (in C) * Rpu RT B=3200 B=3500 B=3900 TLOW 24/32 * GPO1 10 k 30 k -3.0 0.0 +2.0 THIGH 10/32 * GPO1 10 k 4.5 k +49 +46 +44 CHARGE LED INDICATOR Since normal LED control via the SPI bus is not always possible in the charging mode, an 8.0 mA max current sink is provided at the CHRGLED pin for an LED connected to CHRGRAW. The LED will be activated when standalone charging is started, and will remain under control of the state machine also when the application is powered on. At the end of charge, the LED is automatically disabled. Through the CHRGLEDEN bit, the LED can be forced on. In software controlled charging, the LED is under full control of this CHRGLEDEN bit. Table 74. Charge LED Drivers Main Characteristics Parameter Condition Trickle LED current Min Typ Max Units CHRGLED = 2.5 V - - 8.0 mA CHRGLED = 0.7 V 5.0 - - mA Notes 81. Above conditions represent respectively a USB and a collapsed charger case Table 75. Charge LED Driver Control CHRGLEDEN CHRGLED 0 (default) Auto 1 On MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 95 FUNCTIONAL DEVICE OPERATION BATTERY INTERFACE AND CONTROL CHARGER OPERATION USB CHARGING The USB VBUS line in this case, is used to provide a supply within the USB voltage limits and with at least 500 mA of current drive capability. When trickle charging from the USB cable, it is important not to exceed the 100 mA, in case of a legacy USB bus. The appropriate charge current level ICHRG[2:0] = (0001) is 80 mA typical which accounts for the additional current through the charge LED indicator. WALL CHARGING No distinction can be made between a USB Host or a wall charger. Therefore, when attaching a wall charger, the CHRGSE1B pin must be forced low as a charger attach indicator. The CHRGSE1B pin has a built-in weak pull-up to VCORE. In the application, this pin is preferably pulled low, with for instance an NPN of which the base is pulled high through a resistor to CHRGRAW. The state of the CHRGSE1B pin is reflected through the CHRGSE1BS bit. When CHRGSE1B changes state a CHRGSE1BI is generated. No specific debounce is applied to the CHRGSE1B detector. Table 76. Charger Detector Characteristics Parameter Min Typ Max Units - 100 - kOhm Logic Low 0.0 - 0.3 V Logic High 1.0 - VCORE V CHRGSE1B Pull-up Condition To VCORE If an application is to support wall chargers and USB on separate connectors, it is advised to separate the VBUS and the CHRGRAW on the PCB. For these applications, charging from USB is no longer possible. For proper operation, a 120 kOhm pull-down resistor should be placed at VBUS. STANDALONE CHARGING A standalone charge mode of operation is provided to minimize software interaction. It also allows for a completely discharged battery to be revived without processor control. This is especially important when charging from a USB host or when in single path configuration (M3 replaced by short, BATTFET floating). Since the default voltage and current setting of the charge path regulator may not be the optimum choice for a given application, these values can be reprogrammed through the SPI if the CHGAUTOVIB bit is set. Note that the power limiter can be programmed independent of this bit being set. Upon connecting a USB host to the application with a dead battery, the trickle cycle is started and the current set to the lowest charge current level (80 mA). When the battery voltage rises above the BATTON = 3.4 V threshold, a power up sequence is automatically initiated. The lowest charge current level remains selected until a higher charge current level is set through the SPI after negotiation with the USB host. In case of a power up failure, a second power up will not be initiated to avoid an ambulance mode, the charger circuitry will though continue to charge. The USB dead battery operation following the low-power boot scheme is described further in this chapter. Upon connecting a charger to an application with a dead battery the behavior will be different for serial path and single path configurations. In serial path (M3 present), the application will be powered up with the current through M1M2 set to 500 mA minimum. The internal trickle charge current source will be enabled, set to its lowest level (40 mA) up to BATTMIN, followed by the highest setting (80 mA). The internal trickle charge current is not programmable, but can be turned off by the SPI. In this mode, the voltage and current regulation to BP through the external pass devices M1M2 can be reprogrammed through the SPI. Once the battery is greater than BATTON, it will be connected to BP and further charged through M1/M2 at the same time as the application. In single path (M3 replaced by a short, BATTFET floating), the battery (and therefore BP) is below the BPON threshold. This will be detected and the external charge path will be used to precharge the battery, up to BATTMIN at the lowest level (80 mA), and above at the 500 mA minimum level. Once exceeding BPON, a turn on event is generated and the voltage and current levels can be reprogrammed. When in the serial path and upon initialization of the charger circuitry, and it appears BP stays below BPON, the application will not be powered up, and the same charging scheme is followed as for single path. MC13892 96 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION BATTERY INTERFACE AND CONTROL The precharge will timeout and stop charging, in case it did not succeed in raising the battery to a high enough level: BATTON for internal precharge, external precharge in the case of USB, and BPON for the external precharge, in case of a charger. This is a fault condition and is flagged to the processor by the CHGFAULTI interrupt, and the CHGFAULTS[1:0] bits are set to 10. The charging circuit will stop charging and generate a CHGCURRI interrupt after the battery is fully charged. This is detected by the charge current dropping below the CHGCURR limit. The charger automatically restarts if the battery voltage is below BATTCYCL. Software can bypass this cyclic mode of operation by setting the CYCLB bit. Setting the bit does not prevent interrupts to be generated. During charging, a charge timer is running. When expiring before the CHGCURR limit is reached, the charging will be stopped and an interrupt generated. The charge timer can be reset before it expires by setting the self clearing CHGTMRRST bit. After expiration, the charger needs to be restarted. Proper charge termination and restart is a relatively slow process. Therefore in both of the previous cases, the charging will rapidly resume, in case of a sudden battery bounce. This is detected by BP dropping below the BATTON threshold. Out of any state and after a timeout, the charger state machine can be restarted by removing and reapplying the charger. A software restart can also be initiated by setting the self clearing CHGRESTART bit. The state of the charger logic is reflected by means of the CHGENS bit. This bit is therefore a 1 in all states of the charger state machine, except when in a fault condition or when at the end of charge. In low-power boot mode, the bit is not set until the ACKLPB bit is set. This also means that the CHGENS bit is not cleared when the power limiter interacts, or when the battery temperature is out of range. The charge LED At CHRGLED follows the state of the CHGENS bit with the exception that software can force the LED driver on. The detection of a serial path versus a single path is reflected through the CHRGSSS bit. A logic 1 indicates a serial path. In cases of single path, the pin BATTFET must be left floating. The charging circuit will stop charging, in case the die temperature of the IC exceeds the thermal protection threshold. The state machine will be re-initiated again when the temperature drops below this threshold. Table 77. Charger Timer Characteristics Parameter Condition Charger Timer Precharge Timer Min Typ Max Units - 120 - min External precharge 80 mA Internal precharge 40/80 mA - 270 - min External precharge 400/560 mA - 60 - min Table 78. Charger Fault Conditions Fault Condition CHGFAULTS[1:0] CHGFAULTI Cleared or no fault condition 00 Not generated Over-voltage at CHRGRAW 01 Rising edge Excessive dissipation on M1/M2 01 Rising edge Sudden battery drop below BATTMIN 10 Rising edge Any charge timeout 10 Rising edge Out of temperature 11 Dual edge SOFTWARE CONTROLLED CHARGING The charger can also be operated under software control. By setting CHGAUTOB = 1, full control of the charger settings is assumed by software. The state machine will no longer determine the mode of charging. The only exceptions to this are a charger removal, a charger over-voltage detection and excessive power dissipation in M1/M2. For safety reasons, when a RESETB occurs, the software controlled charging mode is exited for the standalone charging operation mode. In the software controlled charging mode, the internal trickle charger settings can be controlled as well as the M3 operation through FETCTRL (1 = conducting). The latter is only possible if the FETOVRD bit is set. If a sudden drop in BP occurs (BP < BPON) while M3 is open, the charger control logic will immediately close M3 under the condition that BATT > BATTMIN. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 97 FUNCTIONAL DEVICE OPERATION BATTERY INTERFACE AND CONTROL FACTORY MODE In factory mode, power is provided to the application with no battery present. It is not a situation which should occur in the field. The factory mode is differentiated from a USB Host by, in addition to a valid VBUS, a UID being pulled high to the VBUS level during the attach, see Connectivity. In case of a serial path (M3 present), the application will be powered up with M1M2 fully on. The M3 is opened (non conducting) to a separate BP from BATT. However, the internal trickle charge current source is not enabled. All the charger timers as well as the power limiter are disabled. In case of a single path (M3 replaced by a short, BATTFET floating), the behavior is similar to a normal charging case. The application will power up and the charge current is set to the 500 mA minimum level. All the internal timers and pre-charger timers are enabled, while only the charger timer and power limiter function are disabled. In both cases, by setting the CHGAUTOVIB bit, the charge voltage and currents can be programmed. When setting the CHGAUTOB bit the factory mode is exited. USB LOW-POWER BOOT USB low-power boot allows the application to boot with a dead battery within the 100 mA USB budget until the processor has negotiated for the full current capability. This mode expedites the charging of the dead battery and allows the software to bring up the LCD display screen with the message "Charging battery". This is enabled on the IC by hardwiring the MODE pin on the PCB board, as shown in Table 79. Table 79. MODE Pin Programming MODE Pin State Mode Ground Normal Operation VCOREDIG Low-power Boot Allowed Below are the steps required for USB low-power booting: 1. First step: detect a potential low-power boot condition, and qualify if it is enabled. a) VBUS present and not in Factory Mode (either via a wall charger or USB host, since the IC has no knowledge of what kind of device is connected) b) BP<BPON (full power boot if BP>BPON) c) Board level enabling of LPB with MODE pin hardwired to VCOREDIG d) M3 included in charger system (Serial path charging, not Single). If all of these are true, then LPBS=1 and the system will proceed with LPB sequence. If any are false, LPBS = 0. 2. If LPBS = 0, then a normal booting of the system will take place as follows: a) MODE = GND. The INT pin should behave normally, i.e. can go high during Watchdog phase based on any unmasked interrupt. If BP>BATTON, the application will turn on. If BP < BATTON, the PMIC will default to trickle charge mode and a turn on event will occur when the battery is charged above the BATTON threshold. The processor does not support a low-power boot mode, so it powers up normally. b) MODE = VCOREDIG. When coming from Cold Start the INT is kept low throughout the watchdog phase. The processor detects this and will boot normally. The INT behavior is becomes 'normal' when entering On mode, and also when entering watchdog phase from warm start. 3. If LPBS = 1, then the system will boot in low-power as follows: a) Cold Start is initiated in a "current starved bring-up" limited by the charger system's DAC step ICHRG[3:0] = 0001 to stay within 100 mA USB budget. The startup sequence and defaults as defined in the startup table will be followed. Since VBUS is present the USB supplies will be enabled. The charge LED driver is maintained off. b) After the power up sequence, but before entering Watchdog phase, thus releasing the reset lines, the charger DAC current is stepped up to ICHRG[3:0] = 0100. This is in advance of negotiation and the application has to ensure that the total loading stays below the un-negotiated 100 mA limit. c) The INT pin is made high before entering watchdog phase and releasing RESETBMCU. All other interrupts are held off during the watchdog phase. The processor detects this and starts up in a Low-power mode at low clock speed. d) The application processor will enable the PHY in serial FS mode for enumeration. e) If the enumeration fails to get the stepped up current, the processor will bring WDI low. The power tree is shut down, and the charging system will revert to trickle recovery, LPBS reset to 0. (or any subsequent failure: WDI = 0). Also if RESETB transitions to 0 while in LPB (i.e., if BP loading misbehaves and causes a UVDET for example), the system will transition to USB trickle recover, LPBS reset to 0. MC13892 98 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION BATTERY INTERFACE AND CONTROL f) If the enumeration is successful to get the stepped up current the processor will hold WDI high and continues with the booting procedure. * When the SPI is activated, the LPB interrupt LPBI can be cleared; other unmasked interrupts may now become active. When leaving watchdog phase for the On mode, the interrupts will work 'normally' even if LPBI is not cleared. * The SPI bit ACKLPB bit is set to enable the internal trickle charger. The charge LED gets activated. When the battery crosses the BATTMIN threshold the M3.transistor is automatically closed and the battery is charged with the current not taken by the application. * When BP exceeds BPON, the charger state machine will successfully exit the trickle charge mode. This will make LPBS = 0 which generates a LPBI. This interrupt will inform the processor that a full turn on is allowed. Once this happens the application code is allowed to run full speed. BATTERY THERMISTOR CHECK OPERATION By default, the battery thermistor value is taken into account for charging the battery. Upon detection of a supply at CHRGRAW, the core circuitry powers up including VCORE. As soon as VCORE is ready, the output GPO1 is made active high, independently of the state of GPO1EN bit. The resulting voltage at ADIN5 is compared to the corresponding temperature thresholds. If the voltage at ADIN5 is within range, the charging will behave as described thus far, however if out of range the charger state machine will go to a wait state, pause the charge timers, and no current will be sourced to the battery. When the temperature comes back in range, charging is continued again. The actual behavior depends on the configuration the charger circuitry at the moment the temperature range is exceeded. Table 80. Battery Thermistor Check Charger States State for temperature Configuration State for temperature back in range out of range ICin "On" State IC in "Off" State Internal precharging on a charger M1M2 = 560 mA / SPI setting, M3 = Open, Itrickle = 0mA Internal precharge Initialization Internal precharging on USB in USB Low-power Boot M1M2 = 400 mA M3 = Open, Itrickle = 0mA Low-power Boot Precharge Initialization All other non fault charging modes and configurations M1M2 = 0 mA M3 Closed Initialization Initialization The battery thermistor check can be disabled by setting the THCHKB bit. This is useful in applications where battery packs without thermistor may be used. This bit defaults to '0', which means that initial power up only can be achieved with an already charged battery pack or on a charger, but not on a USB Host without low-power boot support. Alternatively, one can bias ADIN5 to get within the temperature window. Setting the SPI bit to disable the thermistor check will also inhibit the automatic enabling of the GPO1 output. The GPO1 output still remains controllable through GPO1EN. As an additional feature, the charger state machine will end up in an out of temperature state when the die temperature is below -20 C, independent of the setting of the THCHKB bit. Notes: When using the battery charger as the only source of power, as in a battery-less application, the following precautions should be observed: * It is still necessary to connect ADIN5 to either VCOREDIG or a midpoint of a divider from GPIO1 to ground since the battery charger still interprets this voltage as the battery pack thermistor by default. * The charger state machine ends up in an out of temperature state when the die temperature is below -20 C. The battery charger path, thus, must not be used in battery-less applications expected to operate below -20 C. * Very careful budgeting of the total current consumption and voltage standoff from CHRGRAW to BPSNS must be made, since the power limiter is operational by default, and a battery less system won't have a source of current if the power dissipation limit is reached. * If operating from a USB host the unit load limit (100 mA max.) must still be observed. * If operating from a "wall charger", and if there is no battery, there is an period of approximately 85 ms after RESETB is released, but before the current limit is set to a nominal 560 mA. If the total current demand is greater than this limit, the voltage may collapse and RESETB may pulse a few times (depending in part in the system load and dependence on RESETB.) Therefore, at the end of this time, RESETB may or may not be active. It may be necessary to use one of the other turn on events (such as PWRONx) to turn it back on. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 99 FUNCTIONAL DEVICE OPERATION ADC SUBSYSTEM ADC SUBSYSTEM CONVERTER CORE The ADC core is a 10-bit converter. The ADC core and logic run on 2/3 of the switcher PLL generated frequency, so approximately 2.0 MHz. If an ADC conversion is requested while the PLL was not active, it will automatically be enabled by the ADC. A 32.768 kHz equivalent time base is derived from this to the ADC time events. The ADC is supplied from VCORE. The ADC core has an integrated auto calibration circuit which reduces the offset and gain errors. The switcher PLL is programmable, see Supplies. When the switcher frequency is changed, the frequency applied to the ADC converter will change accordingly. Although the conversion time is inversely proportional to the PLLX[2:0] setting, this will not influence the ADC performance. The locally derived 32.768 kHz will remain constant in order not to influence the different timings depending on this time base. INPUT SELECTOR The ADC has 8 input channels. Table 81 gives an overview of the attributes of the A to D channels. Table 81. ADC Inputs Channel ADA1[2:0] ADA2[2:0] 0 000 Battery Voltage (BATT) 1 001 Battery Current (BATT-BATTISNSCC) 2 010 Application Supply (BPSNS) 3 011 Charger Voltage (CHRGRAW) 4 100 Charger Current (CHRGISNS-BPSNS) 5 101 6 110 Signal read Scaling Scaled Version /2 0 - 2.4 V x20 -1.2 - 1.2 V 0 - 4.8 V /2 0 - 2.4 V 0 - 12 V 0 - 20 V /5 /10 0 - 2.4 V 0 - 2.4 V -300 mV - 300 mV (83) x4 -1.2 - 1.2 V General Purpose ADIN5 (Battery Pack Thermistor) 0 - 2.4 V x1 0 - 2.4 V General Purpose ADIN6 Backup Voltage (LICELL) 0 - 2.4 V 0 - 3.6 V x1 x2/3 0 - 2.4 V 0 - 2.4 V General Purpose ADIN7/ADIN7B 0 - 2.4 V x1 0 - 2.4 V 0 - BP /2 0 - 2.4 V 0 - VIOHI /2 0 - 1.4 V - - 1.2 - 2.4 V 0 - 4.8 V /2 0 - 2.4 V General Purpose ADIN7 7 111 General Purpose ADIN7B Die Temperature UID Input Level 0 - 4.8 V -60 mV - 60 mV (82) Notes 82. Equivalent to -3.0 to +3.0 A of current with a 20 mOhm sense resistor 83. Equivalent to -3.0 to +3.0 A of current with a 100 mOhm sense resistor The above table is valid when setting the bit ADSEL = 0 (default). If setting the bit to a 1, the touch screen interface related inputs are mapped on the ADC channels 4 to 7 and channels 0 to 3 become unused. For more details see the touch screen interface section. Some of the internal signals are first scaled to adapt the signal range to the input range of the ADC. The charge current and the battery current are indirectly read out by the voltage drop over the resistor in the charge path and battery path respectively. For details on scaling see the dedicated readings section. In case the source impedance is not sufficiently low on the directly accessible inputs ADIN5, ADIN6, ADIN7, and the muxed GPO4 path, an on chip buffer can be activated through the BUFFEN bit. If this bit is set, the buffer will be active on these specific inputs during an active conversion. Outside of the conversions the buffer is automatically disabled. The buffer will add some offset, but will not impact INL and DNL numbers except for input voltages close to zero. MC13892 100 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION ADC SUBSYSTEM Table 82. ADC Input Specification Parameter Source Impedance Condition Min Typ Max Units No bypass capacitor at input - - 5.0 kOhm Bypass capacitor at input 10 nF - - 30 kOhm Input Buffer Offset BUFFEN = 1 -5.0 - 5.0 mV Input Buffer Input Range BUFFEN = 1 0.02 - 2.4 V When considerably exceeding the maximum input of the ADC at the scaled or unscaled inputs, the reading result will return a full scale. It has to be noted that this full scale does not necessarily yield a 1023 DEC reading, due to the offsets and calibration applied. The same applies for when going below the minimum input where the corresponding 0000 DEC reading may not be returned. CONTROL The ADC parameters are programmed by the processors via the SPI. Up to two ADC requests can be queued, and locally these requests are arbitrated and executed. When a conversion is finished, an interrupt ADCDONEI is generated. The interrupt can be masked with the ADCDONEM bit. The ADC can start a series of conversions by a rising edge on the ADTRIG pin or through the SPI programming by setting the ASC bit. The ASC bit will self clear once the conversions are completed. A rising edge on the ADTRIG pin will automatically make the ASC bit high during the conversions. When started, always eight conversions will take place; either 1 for each channel (multiple channel mode, RAND = 0) or eight times the same channel (single channel mode, bit RAND = 1). In single channel mode, the to be converted channel needs to be selected with the ADA1[2:0] setting. This setting is not taken into account in multiple channel mode. In order to perform an auto calibration cycle, a series of ADC conversions is started with ADCCAL = 1. The ADCCAL bit is cleared automatically at the end of the conversions and an ADCDONEI interrupt is generated. The calibration only needs to be performed before a first utilization of the ADC after a cold start. The conversion will begin after a small synchronization error of a few microseconds plus a programmable delay from 1 (default) to 256 times the 32 kHz equivalent time base by programming the bits ATO[7:0]. This delay cannot be programmed to 0 times the 32 kHz in order to allow the ADC core to be initialized during the first 32 kHz clock cycle. The ATO delay can also be included between each of the conversions by setting the ATOX bit. Once a series of eight A/D conversions is complete, they are stored in a set of eight internal registers and the values can be read out by software (except when having done an auto calibration cycle). In order to accomplish this, the software must set the ADA1[2:0] and ADA2[2:0] address bits to indicate which values will be read out. This is set up by two sets of addressing bits to allow any two readings to be read out from the 8 internal registers. For example, if it is desired to read the conversion values stored in addresses 2 and 6, the software will need to set ADA1[2:0] to 010 and ADA2[2:0] to 110. A SPI read of the A/D result register will return the values of the conversions indexed by ADA1[2:0] and ADA2[2:0]. ADD1[9:0] will contain the value indexed by ADA1[2:0], and ADD2[9:0] will contain the conversion value indexed by ADA2[2:0]. An additional feature allows for automatic incrementing of the ADA1[2:0] and ADA2[2:0] addressing bits. This is enabled with bits ADINC1 and ADINC2. When these bits are set, the ADA1[2:0] and ADA2[2:0] addressing bits will automatically increment during subsequent readings of the A/D result register. This allows for rapid reading of the A/D results registers with a minimum of SPI transactions. The ADC core can be reset by setting the self clearing ADRESET bit. As a result the internal data and settings will be reset but the SPI programming or readout results will not. To restart a new ADC conversion after a reset, all ADC SPI control settings should therefore be reprogrammed. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 101 FUNCTIONAL DEVICE OPERATION ADC SUBSYSTEM DEDICATED READINGS CHANNEL 0 BATTERY VOLTAGE The battery voltage is read at the BATT pin at channel 0. The battery voltage is first scaled as V(BATT)/2 in order to fit the input range of the ADC. Table 83. Battery Voltage Reading Coding Conversion Code ADDn[9:0] Voltage at input ADC in V Voltage at BATT in V 1 111 111 111 2.400 4.800 1 000 010 100 1.250 2.500 0 000 000 000 0.000 0.000 CHANNEL 1 BATTERY CURRENT The current flowing out of and into the battery can be read via the ADC, by monitoring the voltage drop over the sense resistor between BATT and BATTISNSCC. This function is enabled by setting BATTICON = 1. The battery current can be read either in multiple channel mode or in single channel mode. In both cases, the battery terminal voltage at BATT, and the voltage difference between BATT and BATTISNS, are sampled simultaneously but converted one after the other. This is done to effectively perform the voltage and current reading at the same time. In multiple channel mode, the converted values are read at the assigned channel. In single channel mode and ADA1[2:0] = 001, the converted result is available in 4 pairs of battery voltage and current reading as shown in Table 84. Table 84. Battery Current Reading Sequence ADC Trigger Signals Sampled Signal Converted Readout Contents 0 BATT, BATT - BATTISNSCC BATT Channel 0 BATT 1 - BATT - BATTISNSCC Channel 1 BATT - BATTISNSCC 2 BATT, BATT - BATTISNSCC BATT Channel 2 BATT 3 - BATT - BATTISNSCC Channel 3 BATT - BATTISNSCC 4 BATT, BATT - BATTISNSCC BATT Channel 4 BATT 5 - BATT - BATTISNSCC Channel 5 BATT - BATTISNSCC 6 BATT, BATT - BATTISNSCC BATT Channel 6 BATT 7 - BATT - BATTISNSCC Channel 7 BATT - BATTISNSCC If the BATTICON bit is not set, the ADC will return a 0 reading for channel 1. The voltage difference between BATT and BATTISNS is first amplified to fit the ADC input range as V(BATT-BATTISNS)*20. Since battery current can flow in both directions, the conversion is read out in 2's complement format. Positive readings correspond to the current flow out of the battery, and negative readings to the current flowing into the battery. Table 85. Battery Current Reading Coding Voltage at Input, ADC in mV BATT - BATTISNS in mV Current through 20 mOhm in mA 0 111 111 111 1200.00 60 3000 From battery 0 000 000 001 2.346 0.117 5.865 From battery 0 000 000 000 0.0 0.0 0.0 1 111 111 111 -2.346 -0.117 5.865 To battery 1 000 000 000 -1200.00 -60 3000 To battery Conversion Code, ADDn[9:0] Current Flow - MC13892 102 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION ADC SUBSYSTEM The value of the sense resistor used, determines the accuracy of the result as well as the available conversion range. Note that excessively high values can impact the operating life of the device due to extra voltage drop across the sense resistor. Table 86. Battery Current Reading Specification Parameter Condition Min Typ Max Units Amplifier Gain 19 20 21 Amplifier Offset -2.0 - 2.0 mV Sense Resistor - 20 - mOhm CHANNEL 2 APPLICATION SUPPLY The application supply voltage is read at the BP pin at channel 2. The battery voltage is first scaled as V(BP)/2 in order to fit the input range of the ADC. Table 87. Application Supply Voltage Reading Coding Conversion Code ADDn[9:0] Voltage at input ADC in V Voltage at BP in V 1 111 111 111 2.400 4.800 1 000 010 101 1.250 2.500 0 000 000 000 0.000 0.000 CHANNEL 3 CHARGER VOLTAGE The charger voltage is measured at the CHRGRAW pin at channel 3. The charger voltage is first scaled in order to fit the input range of the ADC. If the CHRGRAWDIV bit is set to a 1 (default), then the scaling factor is a divide by 5, when set to a 0 a divide by 10. Table 88. Charger Voltage Reading Coding Conversion Code ADDn[9:0] Voltage at input ADC in V Voltage at CHGRAW in V, CHRGRAWDIV = 0 Voltage at CHGRAW in V, CHRGRAWDIV = 1 1 101 010 100 2.000 20.000 10.000 0 000 000 000 0.000 0.000 0.000 CHANNEL 4 CHARGER CURRENT The charge current is read by monitoring the voltage drop over the charge current sense resistor. This resistor is connected between CHRGISNS and BPSNS. The voltage difference is first amplified to fit the ADC input range as V(CHRGISNS-BPSNS)*4. The conversion is read out in a 2's complement format, see Table 89. The positive reading corresponds to the current flow from charger to battery, the negative reading to the current flowing into the charger terminal. Unlike the battery current and voltage readings, the charger current readings are not interleaved with the charger voltage readings, so when RAND = 1 a total of 8 readings are executed. The conversion circuit is enabled by setting the CHRGICON bit to a one. If the CHRGICON bit is not set, the ADC will return a 0 reading for channel 4. Table 89. Charge Current Reading Coding Conversion Code ADDn[9:0] Voltage at input ADC in mV CHRGISNS - BPSNS in mV Current through 100 mOhm in mA Current Flow 0 111 111 111 1200 300.0 3000 To application/battery 0 000 000 001 2.4 0.586 5.865 To application/battery 0 000 000 000 0.0 0.0 0.0 - 1 111 111 111 -2.346 -0.586 5.865 To charger connection 1 000 000 000 -1200 -300.0 3000 To charger connection The value of the sense resistor used determines not only the accuracy of the result as well as the available conversion range, but also the charge current levels. It is therefore advised not to select another value than 100 mOhm. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 103 FUNCTIONAL DEVICE OPERATION ADC SUBSYSTEM CHANNEL 5 ADIN5 AND BATTERY THERMISTOR AND BATTERY DETECT On channel 5, ADIN5 may be used as a general purpose unscaled input, but in a typical application, ADIN5 is used to read out the battery pack thermistor. The thermistor will have to be biased with an external pull-up to a voltage rail greater than the ADC input range. In order to save current when the thermistor reading is not required, it can be biased from one of the general purpose IO's such as GPO1. A resistor divider network should assure the resulting voltage falls within the ADC input range in particular when the thermistor check function is used, see Battery Thermistor Check Circuitry. When the application is on and supplied by the charger, a battery removal can be detected by a battery thermistor presence check. When the thermistor terminal becomes high-impedance, the battery is considered being removed. This detection function is available at the ADIN5 input and can be enabled by setting the BATTDETEN bit. The voltage at ADIN5 is compared to the output voltage of the GPO1 driver, and when the voltage exceeds the battery removal detect threshold, the sense bit BATTDETBS is made high and after a debounce the BATTDETBI interrupt is generated. Table 90. Battery Removal Detect Specification Parameter Battery Removal Detect Condition Threshold(84) Min Typ Max Units - 31/32 * GPO1 - V Notes 84. This is equivalent to a 10 kOhm pull-up and a 10 kOhm thermistor at -35 C. CHANNEL 6 ADIN6 AND COIN CELL VOLTAGE On channel 6, ADIN6 may be used as a general purpose unscaled input. In addition, on channel 6, the voltage of the coin cell connected to the LICELL pin can be read (LICON=1). Since the voltage range of the coin cell exceeds the input voltage range of the ADC, the LICELL voltage is first scaled as V(LICELL)*2/3. In case the voltage at LICELL drops below the coin cell disconnect threshold (see Clock Generation and Real Time Clock), the voltage at LICELL can still be read through the ADC. Table 91. Coin Cell Voltage Reading Coding Conversion Code Voltage at ADC input (V) ADDn[9:0] Voltage at LICELL (V) 1 111 111 111 2.400 3.6 1 000 000 000 1.200 1.8 0 000 000 000 0.000 0.0 CHANNEL 7 ADIN7 AND ADIN7B, UID AND DIE TEMPERATURE On channel 7, ADIN7 may be used as a general purpose unscaled input (ADIN7DIV = 0) or as a divide by 2 scaled input (ADIN7DIV = 1). The latter allows converting signals that are up to twice the ADC converter core input range. In a typical application, an ambient light sensor is connected here. A second general purpose input ADIN7B is available on channel 7. This input is muxed on the GPO4 pin. The input voltage can be scaled by setting the ADIN7DIV bit. In the application, a second ambient light sensor is supposed to be connected here. Note that the GPO4 will have to be configured to allow for the proper routing of GPO4 to the ADC, see General Purpose Outputs. In addition, on channel 7, the voltage of the USB ID line connected to the UID pin can be read. Since the voltage range of the ID line exceeds the input voltage range of the ADC, the UID voltage is first scaled as V(UID)/2. Table 92. UID Voltage Reading Coding Conversion Code Voltage at ADC input (V) ADDn[9:0] Voltage at UID (V) 1 111 111 111 2.400 4.80 - 5.25 0 000 000 000 0.000 0.0 Also on channel 7, the die temperature can be read out. The relation between the read out code and temperature is given in Table 93. MC13892 104 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION ADC SUBSYSTEM Table 93. Die Temperature Voltage Reading Parameter Minimum Typical Maximum Unit Die Temperature Read Out Code at 25 C - 680 - Decimal Temperature change per LSB - +0.4244 C - C/LSB Slope error - - 5.0 % Table 94. ADC Channel 7 Scaling Selection ADIN7DIV ADIN7SEL1 ADIN7SEL0 Channel 7 Routing and Scaling 0 0 0 General purpose input ADIN7, Scaling = 1 1 0 0 General purpose input ADIN7, Scaling = 1 / 2 x 0 1 Die temperature x 1 0 UID pin voltage, Scaling = 1 / 2 0 1 1 General purpose input ADIN7B, Scaling = 1 1 1 1 General purpose input ADIN7B, Scaling = 1 / 2 ADC ARBITRATION The ADC converter and its control is based on a single ADC converter core with the possibility to store two requests, and to store both their results as shown in Figure 27. This allows two independent pieces of software to perform ADC requests. Figure 27. ADC Request Handling The programming for the two requests, the one to the 'ADC' and to the 'ADC BIS', uses the same SPI registers. The write access to the control of 'ADC BIS' is handled via the ADCBISn bits located at bit position 23 of the ADC control registers, which functions as an extended address bit. By setting this bit to a 1, the control bits which follow are destined for the 'ADC BIS'. ADCBISn will always read back 0 and there is no read access to the control bits related to 'ADC BIS'. The read results from the 'ADC' and 'ADC BIS' conversions are available in two separate registers. The following diagram schematically shows how the ADC control and result registers are set-up. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 105 FUNCTIONAL DEVICE OPERATION ADC SUBSYSTEM 8 Bit Address Header 24 B it Data Location 43 ADC Control Register 0 R/W Bi t Address Bits Nul l ADC Bi t BIS0 ADC Control Bits Location 44 ADC Control Register 1 R/W Bi t Address Bits Nul l ADC Bi t BIS1 ADC Control Bits Location 45 ADC Result Register ADC0 R/W Bi t Address Bits Nul l Bi t Location 46 ADC Control Register 2 R/W Bi t Address Bits Nul l ADC Bi t BIS2 Location 47 ADC Result Register ADC1 R/W Bi t Address Bits Nul l Bi t ADC Result Bits ADC Control Bits ADC BIS Result Bits Figure 28. ADC Register Set for ADC BIS Access There are two interrupts available to inform the processor when the ADC has finished its conversions, one for the standard ADC conversion ADCDONEI, and one for the ADCBIS conversion ADCBISDONEI. These interrupts will go high after the conversion, and can be masked. When two requests are queued, the request for which the trigger event occurs the first will be converted the first. During the conversion of the first request, an ADTRIG trigger event of the other request is ignored, if for the other request the TRIGMASK bit was set to 1. When this bit is set to 0, the other request ADTRIG trigger event is memorized, and the conversion will take place directly after the conversions of the first request are finished. The following diagram shows the influence of the TRIGMASK bit. The TRIGMASK bit is particularly of use when an ADC conversion has to be lined up to a periodically ADTRIG initiated conversion. In case of ASC initiated conversions, the TRIGMASK bit is of no influence. Figure 29. TRIGMASK Functional Diagram To avoid results of previous conversions getting overwritten by a periodical ADTRIG signal, a single shot function is enabled by setting the ADONESHOT bit to a one. In that case, only at the first following conversion, an ADTRIG trigger event is accepted. ASC events are not affected by this setting. Before performing a new single shot conversion, the ADONESHOT bit first needs to be cleared. Note that this bit is available for each of the conversion requests 'ADC' or 'ADC BIS', so can be set independently. It is possible to queue two ADTRIG triggered conversions. Both conversions will be executed with a priority based on the TRIGMASK setting. If both conversion requests have identical TRIGMASK settings, priority is given to the 'ADC' conversion over the 'ADC BIS' conversion. Note that the ADONESHOT is also taken into account. To avoid that the ADTRIG input inadvertently triggers a conversion, the ADTRIGIGN bit can be set which will ignore any transition on the ADTRIG pin. The ADC completely ignores either ADTRIG or ASC pulses while ADEN is low. When reading conversion results, it is preferable to make ADEN = 0. MC13892 106 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION ADC SUBSYSTEM TOUCH SCREEN INTERFACE The touch screen interface provides all circuitry required for the readout of a 4-wire resistive touch screen. The touch screen X plate is connected to TSX1 and TSX2 while the Y plate is connected to TSY1 and TSY2. A local supply TSREF will serve as a reference. Several readout possibilities are offered. In order to use the ADC inputs and properly convert and readout the values, the bit ADSEL should be set to a 1. This is valid for touch screen readings as well as for general purpose reading on the same inputs. The touch screen operating modes are configured via the TSMOD[2:0] bits show in the following table. Table 95. Touch Screen Operating Mode TSMOD2 TSMOD1 TSMOD0 Mode Description x 0 0 Inactive Inputs TSX1, TSX2, TSY1, TSY2 can be used as general purpose ADC inputs 0 0 1 Interrupt Interrupt detection is active. Generates an interrupt TSI when plates make contact. TSI is dual edge sensitive and 30 ms debounced 1 0 1 Reserved Reserved for a different interrupt mode 0 1 x Touch Screen ADC will control a sequential reading of 2 times a XY coordinate pair and 2 times a contact resistance 1 1 x Reserved Reserved for a different reading mode In inactive mode, the inputs TSX1, TSX2, TSY1, and TSY2 can be used as general purpose inputs. They are respectively mapped on ADC channels 4, 5, 6, and 7. In interrupt mode, a voltage is applied to the X-plate (TSX2) via a weak current source to VCORE, while the Y-plate is connected to ground (TSY1). When the two plates make contact both will be at a low potential. This will generate a pen interrupt to the processor. This detection does not make use of the ADC core or the TSREF regulator, so both can remain disabled. In touch screen mode, the XY coordinate pairs and the contact resistance are read. The X-coordinate is determined by applying TSREF over the TSX1 and TSX2 pins while performing a high-impedance reading on the Y-plate through TSY1. The Y coordinate is determined by applying TSREF between TSY1 and TSY2, while reading the TSX1 pin. The contact resistance is measured by applying a known current into the TSY1 terminal of the touch screen and through the terminal TSX2, which is grounded. The voltage difference between the two remaining terminals TSY2 and TSX1 is measured by the ADC, and equals the voltage across the contact resistance. Measuring the contact resistance helps in determining if the touch screen is touched with a finger or stylus. To perform touch screen readings, the processor will have to select the touch screen mode, program the delay between the conversions via the ATO and ATOX settings, trigger the ADC via one of the trigger sources, wait for an interrupt indicating the conversion is done, and then read out the data. In order to reduce the interrupt rate and to allow for easier noise rejection, the touch screen readings are repeated in the readout sequence. Table 96. Touch Screen Reading Sequence ADC Conversion Signals sampled Readout Address (85) 0 X position 000 1 X position 001 2 Dummy 010 3 Y position 011 4 Y position 100 5 Dummy 101 6 Contact resistance 110 7 Contact resistance 111 Notes 85. Address as indicated by ADA1[2:0] and ADA2[2:0] The dummy conversion inserted between the different readings is to allow the references in the system to be pre-biased for the change in touch screen plate polarity and will read out as '0'. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 107 FUNCTIONAL DEVICE OPERATION ADC SUBSYSTEM Figure 30 shows how the ATO and ATOX settings determine the readout sequence. The ATO should be set long enough so that the touch screen can be biased properly before conversions start. Touchscreen Readout for ATOX=0 1/32K ATO+1 Trigger ATO+1 ATO+1 Conversions 0, 1, 2 Touchscreen Polarization Conversions 3, 4, 5 End of Conversi on 2 New Touchscreen Polarization Conversions 6, 7 End of Conversion 5 New Touchscreen Polarization End of Conversion 7 Touchscreen De-Polarization Touchscreen Readout for ATOX=1 1/32K ATO+1 Trigger ATO+1 Conversion 0 ATO+1 Conversion 1 Touchscreen Polarization ATO+1 Conversion 2 Etc. Conversion 3 End of Conversion 2 New Touchscreen Pol arization Figure 30. Touch Screen Reading Timing The main resistive touch screen panel characteristics are listed in Table 5. The switch matrix and readout scheme is designed such that the on chip switch resistances are of no influence on the overall readout. The readout scheme however does not account for contact resistances as present in the touch screen connectors. Therefore, the touch screen readings will have to be calibrated by the user or in the factory where one has to point with a stylus the opposite corners of the screen. When reading out the X-coordinate, the 10-bit ADC reading represents a 10-bit coordinate with '0' for a coordinate equal to TSX2, and full scale '1023' when equal to TSX1. When reading out the Y-coordinate, the 10-bit ADC reading represents a 10-bit coordinate with '0' for a coordinate equal to TSY2, and full scale '1023' when equal to TSY1. When reading the contact resistance the 10-bit ADC reading represents the voltage drop over the contact resistance created by the known current source multiplied by two. Table 97. Touchscreen Interface Characteristics Parameter Condition Interrupt Threshold for Pressure Application Interrupt Threshold for Pressure Removal Current Source Inaccuracy Over-temperature Min Typ Max Unit 40 50 60 kOhm 60 80 95 kOhm - - 20 % The reference for the touch screen is TSREF and is powered from VCORE. In touch screen operation, TSREF is a dedicated regulator. No other loads than the touch screen should be connected here. When the ADC performs non touch screen conversions, the ADC does not rely on TSREF and the reference can be disabled. In applications not supporting touch screen at all, the TSREF can be used as a low current general purpose regulator, or it can be kept disabled and the bypass capacitor omitted. The operating mode of TSREF can be controlled with the TSREFEN bit in the same way as some other general purpose regulators are controlled, see Linear Regulators. COULOMB COUNTER As indicated earlier on in this Section, the current into and from the battery can be read out through the general purpose ADC as a voltage drop over the R1 sense resistor. Together with battery voltage reading, the battery capacity can be estimated. A more accurate battery capacity estimation can be obtained by using the integrated Coulomb Counter. The Coulomb Counter (or CC) monitors the current flowing in/out of the battery by integrating the voltage drop across the battery current sense resistor R1, followed by an A to D conversion. The result of the A to D conversion is used to increase/ decrease the contents of a counter that can be read out by software. This function will require a 10 F output capacitor to perform MC13892 108 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION ADC SUBSYSTEM a first order filtering of the signal across R1. Due to the sampling of the A to D converter and the filtering applied, the longer the software waits before retrieving the information from the CC, the higher the accuracy. The capacitor will be connected between the pins CFP and CFM, see Figure 31. Figure 31. Coulomb Counter Block Diagram The CC results are available in the 2's complement CCOUT[15:0] counter. This counter is preferably reflecting 1 Coulomb per LSB. As a reminder, 1 Coulomb is the equivalent of 1 Ampere during 1 second, so a current of 20 mA during 1 hour is equivalent to 72C. However, since the resolution of the A to D converter is much finer than 1C, the internal counts are first to be rescaled. This can be done by setting the ONEC[14:0] bits. The CCOUT[15:0] counter is then increased by 1 with every ONEC[14:0] counts of the A to D converter. For example, ONEC[14:0] = 000 1010 0011 1101 BIN = 2621 DEC yields 1C count per LSB of CCOUT[15:0] with R1 = 20 mOhm. The CC can be reset by setting the RSTCC bit. This will reset the digital blocks of the CC and will clear the CCOUT[15:0] counter. The RSTCC bit gets automatically cleared at the end of the reset period which may take up to 40 s. The CC is started by setting the STARTCC bit. The CC is disabled by setting this bit low again. This will not reset the CC settings nor its counters, so when restarting the CC with STARTCC, the count will continue. When the CC is running it can be calibrated. An analog and a digital offset calibration is available. The digital portion of the CC is by default permanently corrected for offset and gain errors. This function can be disabled by setting the CCCALDB bit. However, this is not advisable. In order to calibrate the analog portion of the CC, the CCCALA bit is set. This will disconnect the inputs of the CC from the sense resistor and will internally short them together. The CCOUT[15:0] counter will accumulate the analog error over time. The calibration period can be freely chosen by the implementer and depends on the accuracy required. By setting the ONEC[14:0] = 1 DEC this process is sped up significantly. By reading out the contents of the CCOUT[15:0] and taking into account the calibration period, software can now calculate the error and account for it. Once the calibration period has finished the CCCALA bit should be cleared again. One optional feature is to apply a dithering to the A to D converter to avoid any error in the measurement due to repetitive events. To enable dithering the CCDITHER bit should be set. In order for this feature to be operational, the digital calibration should remain enabled, so the CCCALDB bit should not be set. Table 98. Coulomb Counter Characteristics Parameter Condition Min Typ Max Unit Sense resistor R1 Placed in Battery path of Charger system -- 20 - m Sensed current Through R1 1.0 - 3000 mA On consumption CC active - 10 20 A Resolution 1LSB Increment - 381.47 - C MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 109 FUNCTIONAL DEVICE OPERATION ADC SUBSYSTEM As follows from the previous description, using the CC requires a number of programming steps. A typical programming example is given below. 1. SPI Access 1: Initialize * Reg 9: Write STARTCC = 1, RSTCC = 1, CCCALA = 1, CCDITHER = 1, CCCALDB = 0 * RSTCC will be self clearing * Register 10 is NOT to be programmed since by default the ONEC[14:0] scaler is set to 1 2. Wait for analog calibration period 3. SPI Access 2: Set scaler * Reg 10: Write ONEC to desired value for CC use, for instance 2621DEC 4. SPI Access 3: Read analog offset and reset CC * Reg 9: Write STARTCC = 1, RSTCC = 1, CCCALA = 0, CCDITHER = 1, CCCALDB = 0 * During the write access, on the MISO read line the most recent CCOUT[15:0] is available * RSTCC will be self clearing From this point on the ACC is running properly and CCOUT[15:0] reflects the accumulated charge. In order to be sure the contents of the CCOUT[15:0] are valid, a CCFAULT bit is available. CCFAULT will be set '1' if the CCOUT content is no longer valid, this means the bit gets set when a fault condition occurs and stays latched till cleared by software. There is no interrupt associated to this bit. The following fault conditions are covered. Counter roll over: CCOUT[15:0] = 8000HEX This occurs when the contents of CCOUT[15:0] go from a negative to a positive value or vice versa. Software may interpret incorrectly the battery charge by this change in polarity. When CCOUT[15:0] becomes equal to 8000HEX the CCFAULT is set. The counter stays counting so its contents can still be exploited. Battery removal: 'BP<UVDET' When removing and replacing the battery, the contents of the counter are no longer valid. A battery removal is characterized by the input supply to the IC dropping below the under voltage detect threshold, so BP<UVDET. To avoid false detection due to short power cuts, the CCFAULT is set only after a long debounce of 1 second. Battery removal when charging: BATTDETBS = 1 The battery removal detection as described previously, is not applicable when charging, since the charger will continue to supply the application and the BP will not drop below UVDET. To still detect a battery removal, one can use the battery detect function as described in the channel description earlier in this chapter. When the sense bit BATTDETBS becomes a 1, the CCFAULT is set only after a long debounce of 1 second. MC13892 110 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION CONNECTIVITY CONNECTIVITY USB INTERFACE The MC13892 contains the regulators required to supply the PHY contained in the i.MX51, i.MX37, i.MX35, and i.MX27 processors. The regulators used to power the external PHY in the i.MX51 and i.MX37 are VUSB, VUSB2, and VUSB for the i.MX35 and i.MX27 processors. The MC13892 also provides the 5.0 V supply for USB OTG operation. The USB interface may be used for portable product battery charging (refer to Battery Interface and Control for more details on the charging system). Finally included are comparators/detectors for VBUS and ID detection. The USB interface is illustrated in the following diagram. Figure 32. USB Interface SUPPLIES The VUSB regulator is used to supply 3.3 V to the external USB PHY. The UVBUS line of the USB interface is supplied by the host in the case of host mode operation, or by the integrated VBUS generation circuit, in the case of USB OTG mode operation. The VBUS circuit is powered from the SWBST boost supply to ensure OTG current sourcing compliance through the normal discharge range of the main battery. The VUSB regulator can be supplied from the UVBUS wire of the cable when supplied by a host in the case of host mode operation, or by the SWBST voltage brought in at the VINUSB pin and internally connected to the VBUS pin for OTG mode operation. The VUSBIN SPI bit is used to make the selection between host or OTG mode operation as defined in Table 99. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 111 FUNCTIONAL DEVICE OPERATION CONNECTIVITY Table 99. VUSB Input Source Control Parameter VUSBIN Value Function 0 Powered by Host: UVBUS powers VUSB 1 OTG mode: SWBST internally switched to supply the VUSB regulator, and SWBST will drive VBUS from the VUSBIN pin as long as VBUSEN pin is logic high = 1 Notes 86. Note that (VUSBIN = 1 and VBUSEN = 1) only closes the switch between the VINUSB and UVBUS pins, but does not enable the SWBST boost regulator (which should be enabled with OTGSWBSTEN = 1). 87. VUSBIN SPI bit initialized by PUMS2 pin configuration at cold start PUMS2 = Open, VUSBIN = 0 PUMS2 = Ground, VUSBIN = 1 The VBUSEN pin along with the VUSBIN SPI bit shown in Table 99, control switching SWBST to drive VBUS in OTG mode. When VBUSEN = 1 and VUSBIN = 1, SWBST will be driving the VBUS. In all other cases, the switch from VINUSB to UVBUS will be open. The VUSBIN SPI bit is initialized by the PUMS2 pin configuration at cold start. When the PUMS2 is open the VUSBIN SPI bit will default to 0, and when PUMS2 is grounded the VUSBIN SPI bit will default to 1. When PUMS2 is grounded, the SWBST will also be enabled by default by setting the OTGSWBSTEN bit = 1. Note that (VBUSEN = 1 and VUSBIN = 1) only closes the switch between VINUSB and UVBUS pins, but does not enable SWBST (this needs to be enabled by setting the SPI bit OTGSWBSTEN = 1). In OTG mode, VUSB and VUSB2 will be automatically enabled by setting the SPI bit VUSBIN to a 1. When SWBST is supplying the UVBUS pin (OTG Mode), it will generate VBUSVALID and BVALID interrupts. These interrupts should not be interpreted as being powered by the host by the software, and the VUSB supply will continue to be supplied by the SWBST output. To prevent the charger from charging in OTG mode, the charger should be put into software controlled mode by setting the CHGAUTOB = 1, and the charge current set to 0 prior to enabling the SWBST to supply the UVBUS pin. The VUSB regulator defaults to on when PUMS2 = Ground, and is supplied by the SWBST output. If a USB host is attached, the switchover to supply the VUSB input by the USB cable (UVBUS pin) is a manual switchover, which will require the following steps via software to switch over properly: receive BVALID interrupt, disable the VUSB regulator (VUSBEN = 0), change the input VUSB to UVBUS instead of SWBST (set VINUSB = 0), and then enable the VUSB regulator (VUSBEN = 1). It will be up to the processor to determine what type of device is connected, either a USB host or a wall charger, and take appropriate action. When the PUMS2 = OPEN, the VUSB regulator will default to off, unless 5.0 V is present on the UVBUS pin. If UVBUS is detected during cold start then the VUSB regulator will be enabled and powered on in the sequence, shown in Power Control System, and it will default, which is supplied by the UVBUS pin. If UVBUS is not detected at cold start then the VUSB will default to off. If UVBUS is detected later, the VUSB regulator will be automatically be enabled and supplied from the UVBUS pin. The VUSB regulator can be enabled independent of OTG or Host Mode by setting the VUSBEN SPI bit The VUSBEN SPI bit is initialized by at startup based on the PUMS2 configuration. With PUMS2 OPEN, the VUSBEN will default to a 1 on power up and will reset to a 1, when either RESETB is valid or VBUS is invalid. This allows the VUSBEN regulator to be enabled automatically if the VUSB regulator was disabled by software. With PUMS2 = GND the VUSBEN bit will be enabled in the power up sequence shown in Power Control System. Since UVBUS is shared with the charger input at the board level (see Battery Interface and Control), the UVBUS node must be able to withstand the same high voltages as the charger. In over-voltage conditions, the VUSB regulator is disabled. The following tables show the USB supplies. VUSB2 is implemented with an integrated PMOS pass FET and has a dedicated supply pin VINUSB2. The pin VINUSB2 should always be connected to BP even in cases where the regulators are not used by the application. Table 100. VUSB2 Voltage Control Parameter VUSB2[1:0] Value Function ILoad max 00 output = 2.400 V 50 mA 01 output = 2.600 V 50 mA 10 output = 2.700 V 50 mA 11 output = 2.775 V 50 mA MC13892 112 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION CONNECTIVITY DETECTION COMPARATORS VBUS detection and qualification is accomplished with two comparators, detailed in Table 101. Comparator results are used to generate associated interrupts, and sense and masking bits are available through SPI (refer to SPI Bitmap). Comparator thresholds are specified for the minimum detect levels, and bits can be used in combination to qualify a VBUS window. Events are communicated via (INT pin) interrupts and managed through SPI registers to allow the application processor to turn off the PHY. As described in Battery Interface and Control, the battery charger system is designed to work with the USB system physical connector. The power input is then brought into an end product on the VBUS pin of the USB connector. For fault condition robustness, VBUS over-voltage protection is included to protect the system and flag an over-voltage situation to the processor via the USBOVI interrupt. Table 101. USB Detect Specifications Parameter Condition Min Typ Max Units 4.4 - 4.65 V Rising trip delay 20 - 24 ms Falling trip delay 8.0 - 12 ms BVALID Comparator Threshold Rising and falling edge 4.0 - 4.4 V BVALID Trip Delay Rising trip delay for turn on event Falling trip delay for turn on event 20 8.0 - - 40 12 ms Over-voltage Protection Level Rising and falling edge 5.6 - 6.0 V - - 1.0 s VBUSValid Comparator trip level Including the USBI debounce VBUSValid trip delay Over-voltage Protection Disconnect Time ID DETECTOR The ID detector is primarily used to determine if a mini-A or mini-B style plug has been inserted into a mini-AB style receptacle on the application. However, it is also supports two additional modes which are outside of the USB standards: a factory mode and a non-USB accessory mode. The state of the ID detection can be read via the SPI to poll dedicated sense bits for a floating, grounded, or factory mode condition on the UID pin. There are also dedicated maskable interrupts for each UID condition as well. The ID detector is based on an on-chip pull-up controlled by the IDPUCNTRL bit. If set high the pull-up is a current source, if set low it is a resistor. ID100KPU switches in an additional pull-up from VCORE to UID (independent of IDPUCNTRL). The UID voltage can be read out via the ADC channel ADIN7, see ADC Subsystem. The ID detector thresholds are listed in Table 102. Further interpretations of non-USB accessory detection may be made for custom vendor applications by evaluation of the ADIN7 conversion reading. Table 102. ID Detection Thresholds UID Pin External Connection UID Pin Voltage IDFLOATS IDGNDS IDFACTORYS Accessory Resistor to Ground 0.18 * VCORE < UID < 0.77 * VCORE 0 1 0 Non-USB accessory is attached (per CEA936-A spec) Grounded 0 < UID < 0.12 * VCORE 0 0 0 A type plug (USB Default Slave) is attached (per CEA-936-A spec) Floating 0.89 * VCORE < UID < VCORE 1 1 0 B type plug (USB Host, OTG default master or no device) is attached. Voltage Applied 3.6V < UID (88) 1 1 1 Factory mode Notes 88. UID maximum voltage is 5.25 V MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 113 FUNCTIONAL DEVICE OPERATION LIGHTING SYSTEM Table 103. USB OTG Specifications Parameter Condition Min Typ Max Units VBUS Input Impedance As A_device 40 - 100 k UID 220K Pull-up (89) IDPUCNTRL = 0, Resistor to VCORE 132 220 308 k UID Pull-up (89) IDPUCNTRL = 1, Current source from VCORE 4.75 5.0 5.25 A UID Parallel Pull-up (89) ID100KPU = 1, Resistor to VCORE 60 100 140 k Notes 89. Note that the UID Pull-ups are not mutually exclusive of each other; they are independently controlled by their enable bits and thus multiple pull-ups can be engaged simultaneously. LIGHTING SYSTEM The lighting system includes backlight drivers for main display, auxiliary display, and keypad. The backlight LEDs are configured in series. Three additional drivers are provided for RGB or general purpose signaling. BACKLIGHT DRIVERS The backlight drivers LEDMD, LEDAD and LEDKP are independent current sink channels. Each driver channel features programmable current levels via LEDx[2:0] as well as programmable PWM duty cycle settings with LEDxDC[5:0]. By a combination of level and PWM settings, the backlight intensity can be adjusted, or a soft start and dimming feature can be implemented. The on period of the serial LED backlight drivers will be adapted to take into account that the serial LED switcher startup time is longer than one half the minimum of the period of the backlight drivers. When applying a duty cycle of less than 100% the backlight drivers will be turned on and off at a repetition rate high enough to avoid flickering and or beat frequencies with the different types of displays. Also, to avoid high frequency spur coupling in the application, the switching edges of the output drivers are softened. The current level is programmable in a low range mode and in a high range mode through the LEDxHI bit. This facilitates the current setting, in case two or more serial LED strings are connected in parallel to the same driver or when using super bright LEDs. Table 104. Backlight Drivers Current Programming LEDx[2:0](90) LEDx Current Level (mA) LEDxHI = 0 LEDxHI = 1 000 0 0 001 3 6 010 6 12 011 9 18 100 12 24 101 15 30 110 18 36 111 21 42 Notes 90. "x Represents MD, AD and KP MC13892 114 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION LIGHTING SYSTEM Table 105. Backlight Drivers Duty Cycle Programming LEDxDC[5:0](91) Duty Cycle 000000 0/32, Off 000001 1/32 ... ... 010000 16/32 ... ... 011111 31/32 100000 to 111111 32/32, Continuously On Notes 91. "x" represents MD, AD, or KP Ramp up and ramp down patterns are implemented in hardware to reduce the burden of real time software control via the SPI to orchestrate dimming and soft start lighting effects. Ramp patterns for each of the drivers is accessed with the corresponding LEDxRAMP bit. The ramp itself is generated by increasing or decreasing the PWM duty cycle with a 1/32 step every 1/64 seconds. The ramp time is therefore a function of the initial set PWM cycle and the final PWM cycle. As an example, starting from 0/32 and going to 32/32 will take 500 ms, while going to from 8/32 to 16/32 takes 125 ms. Note that the ramp function is executed upon every change in PWM cycle setting when the corresponding LEDxRAMP = 1. If a PWM change is programmed via SPI when LEDxRAMP = 0, then the change is immediate rather than spread out over a PWM sweep. A maximum of only two backlight drivers can be activated at the same time, for instance, the main display plus keypad. If all three backlight drivers are enabled through the LEDxEN bits, meaning none of the duty cycles equals 0/32, then none of the drivers will be activated. If two backlight drivers are enabled, they time-share the external boost regulator output. The drivers will automatically be enabled and disabled in a 50/50 percent fashion at a sufficiently high rate. The LED drive current will automatically be doubled to the same luminosity as in a single backlight driver configuration. Figure 33 illustrates the time sharing principle. Assume the MD domain is represented by 6 series white LEDs, and the KP domain is represented by 3 ballasted stacks, that include 3 blue LEDs in each (a diagram of Serial LED configurations is included later in this chapter). One Driver Active Two Drivers Active External Boost LEDKP Current LEDMD Current LEDMD Active LEDMD Active LEDKP Active LEDMD Active LEDKP Active Figure 33. Backlight Drivers Time Sharing Example The "One Driver Active" case shows the general response when driving a single zone of 6 white LEDs. The "Two Drivers Active" case shows the LEDMD zone driven at twice the current for half the time. MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 115 FUNCTIONAL DEVICE OPERATION LIGHTING SYSTEM Table 106. Serial LED Driver Characteristics Parameter(92) Condition Output Current Setting Current Programming Granularity Min Typ Max Units Low Range Mode 0.0 - 15 mA High Range Mode 0.0 - 30 Low Range Mode - 3.0 - High Range Mode - 6.0 - - 1/32 - - 256 - Hz PWM Granularity Repetition Rate Not blinking Absolute Accuracy mA - - 15 % Matching At 400 mV, 21 mA - - 3.0 % Glow and Dimming Speed Per 1/32 duty cycle step - 1/64* - S Notes 92. Equivalent to 500 ms ramp time when going from 0/32 to 32/32 Figure 34 illustrates some possible configurations for the backlight driver. Note that when parallel strings are ganged together on a driver channel, ballasting resistance is recommended to help balance the currents in each leg. External Boost LEDMD 6 LED Main Display External Boost External Boost LEDKP LEDMD 9 LED Keypad LEDAD 6 LED Main Display 3 LED Aux Display LEDMD LEDAD 6 LED Main Display LEDKP 12 LED Keypad Arrangement 2 LED Reduced Keypad Option Figure 34. Serial LED Configurations In the left most example in Figure 34: LEDMD is set at 15 mA (low range), LEDKP is set at 30 mA (high range). When both are operated, then the LEDMD current will pulse at 30 mA and the LEDKP current at 60 mA. This provides an average of 15 mA through the main display backlight LEDs and 30 mA through the keypad backlights LEDs. SIGNALING LED DRIVERS The signaling LED drivers LEDR, LEDG, LEDB are independent current sink channels. Each driver channel features programmable current levels via LEDx[2:0] as well as programmable PWM duty cycle settings with LEDxDC[5:0]. By a combination of both, the LED intensity can be adjusted. By driving LEDs of different colors, color mixing can be achieved. MC13892 116 Analog Integrated Circuit Device Data Freescale Semiconductor FUNCTIONAL DEVICE OPERATION LIGHTING SYSTEM Table 107. Signaling LED Drivers Current Programming LEDx[2:0](93) LEDx Current Level (mA) 000 0.0 001 3.0 010 6.0 011 9.0 100 12 101 15 110 18 111 21 Notes 93. "x" represents for R, G and B Table 108. Signaling LED Drivers Duty Cycle Programming LEDxDC[5:0](94) Duty Cycle 000000 0/32, Off 000001 1/32 ... ... 010000 16/32 ... ... 011111 31/32 1xxxxx 32/32, Continuously On Notes 94. "x" represents R, G and B Blue LEDs or bright green LEDs require more headroom than red and normal green signal LEDs. In the application, a 5.0 V or equivalent supply rail is therefore required. This is provided by the integrated boost regulator SWBST. To make software programming easier, an LEDSWBSTEN SPI bit has been provided in the Blue LED register to enable the boost regulator. Note the enable for the boost regulator is an OR of the following SPI bits (SWBSTEN, USBSWBSTEN, and LEDSWBSTEN). For more details on the boost regulator and its control, see Supplies. As with the backlight driver channels, the signaling LED drivers include ramp up and ramp down patterns are implemented in hardware. Ramp patterns for each of the drivers is accessed with the corresponding LEDxRAMP bit. The ramp itself is generated by increasing or decreasing the PWM duty cycle with a 1/32 step every 1/64 seconds. The ramp time is therefore a function of the initial set PWM cycle and the final PWM cycle. As an example, starting from 0/32 and going to 32/32 will take 500 ms while going to from 8/32 to 16/32 takes 125 ms. Note that the ramp function is executed upon every change in PWM cycle setting. If a PWM change is programmed via SPI when LEDxRAMP = 0, then the change is immediate rather than spread out over a PWM sweep. For color mixing and in order to guarantee a constant color, the color mixing should be obtained by the current level setting so that the intensity is set through the PWM duty cycle. In addition, programmable blink rates are provided. Blinking is obtained by lowering the PWM repetition rate of each of the drivers through LEDxPER[1:0], while the on period is determined by the duty cycle setting. To avoid high frequency spur coupling in the application, the switching edges of the output drivers are softened. During blinking, so LEDxPER[1:0] is not "00", ramping and dimming patterns cannot be applied. Table 109. Signal LED Drivers Period Control LEDxPER[1:0] Repetition Rate Units 00 1/256 s 01 1/8 s 10 1 s 11 2 s MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 117 FUNCTIONAL DEVICE OPERATION LIGHTING SYSTEM Table 110. Signaling LED Driver Characteristics Parameter Condition Absolute Accuracy Min Typ Max Units - - 15 % Matching At 400 mV, 21 mA - - 10 % Leakage LEDxDC[5:0] = 000000 - - 1.0 A Apart from using the signal LED drivers for driving LEDs they can also be used as general purpose open drain outputs for logic signaling or as generic PWM generator outputs. For the maximum voltage ratings. the enable for the boost regulator is an OR of the following SPI bits (SWBSTEN, USBSWBSTEN, and LEDSWBSTEN). For more details on the boost regulator and its control, see Supplies. As with the backlight driver channels, the signaling LED drivers include ramp up and ramp down patterns are implemented in hardware. Ramp patterns for each of the drivers is accessed with the corresponding LEDxRAMP bit. The ramp itself is generated by increasing or decreasing the PWM duty cycle with a 1/32 step every 1/64 seconds. The ramp time is therefore a function of the initial set PWM cycle and the final PWM cycle. As an example, starting from 0/32 and going to 32/32 will take 500 ms while going to from 8/32 to 16/32 takes 125 ms. Note that the ramp function is executed upon every change in PWM cycle setting. If a PWM change is programmed via SPI when LEDxRAMP = 0, then the change is immediate rather than spread out over a PWM sweep. For color mixing and in order to guarantee a constant color, the color mixing should be obtained by the current level setting so that the intensity is set through the PWM duty cycle. In addition, programmable blink rates are provided. Blinking is obtained by lowering the PWM repetition rate of each of the drivers through LEDxPER[1:0], while the on period is determined by the duty cycle setting. To avoid high frequency spur coupling in the application, the switching edges of the output drivers are softened. During blinking, so LEDxPER[1:0] is not "00", ramping and dimming patterns cannot be applied. MC13892 118 Analog Integrated Circuit Device Data Freescale Semiconductor Analog Integrated Circuit Device Data Freescale Semiconductor SPI BITMAP The complete SPI bitmap is given in Table 111 with one register per row for a general overview. A color coding is applied which indicates the type of reset for the bits. Table 111. SPI Bitmap MC13892 Bitmap Color Coding: 31 30 29 28 27 26 25 24 Register Register R/W Label R/T Address 5:0 23 22 Bits Reset by RESETB 21 Null 20 19 18 Bits Reset by RTCPORB 17 16 15 Bits Reset by OFFB 14 13 Bits Without Reset 12 11 Data[23:16] 10 Bits Reloaded at Cold Start 9 8 7 6 Reserved Bits 5 4 Data[15:7] Not Available Bits 3 2 1 0 Data[7:0] 0 Interrupt R/W 0 Status 0 0 0 0 0 0 0 Reserve d Reserved CHGRGSE1BI LOBATLI BPONI CHGCURRI VBUSVALIDI TSI ADCBISDONEI ADCDONEI 1 Interrupt R/W 0 Mask 0 0 0 0 0 1 0 Reserve d Reserved CHGRGSE1BM IDGNDM IDFLOATM Reserved Reserved BVALIDM Reserved LOBATHM LOBATLM BPONM CHGCURRM CCCVM CHGSHORTM CHGREVM CHGFAULTM CHGDETM USBOVM IDFACTORYM VBUSVALIDM TSM ADCBISDONEM ADCDONEM 2 Interrupt Sense 0 0 0 0 0 1 0 0 Reserve d Reserved BPONS CHGCURRS CCCVS 3 Interrupt R/W 0 Status 1 0 0 0 1 1 0 Spare BATTDETBI 4 Interrupt R/W 0 Mask 1 0 0 1 0 0 0 5 Interrupt Sense 1 R 0 0 0 1 0 1 6 Power Up Mode R Sense 0 0 0 1 1 7 Identificatio R n 0 0 0 1 8 Unused R/W 0 0 1 9 Unused R/W 0 0 10 Unused R/W 0 11 R IDFLOATI Reserved Reserved BVALIDI Reserved LOBATHI CCCVI CHGSHORTI CHGREVI CHGFAULTI CHGDETI IDFLOATS Reserved Reserved BVALIDS Reserved LOBATHS LOBATLS Reserved Reserved Reserved Reserved SCPI Spare CLKI THWARNHI THWARNLI LPBI MEMHLDI WARMI Spare BATTDETBIM Reserved Reserved Reserved Reserved SCPM Spare CLKM THWARNHM THWARNLM LPBM MEMHLDM WARMM 0 Spare BATTDETBS Reserved Reserved Reserved Reserved Spare CLKS LPBS 0 0 Spare 1 1 0 0 0 0 0 1 0 0 1 0 0 1 0 1 0 0 Unused R/W 0 0 1 0 1 1 0 12 Unused R/W 0 0 1 1 0 0 0 13 Power R/W 0 Control 0 0 1 1 0 1 0 14 Power R/W 0 Control 1 0 1 1 1 0 0 Reserved Reserved Spare Spare THWARNHS THWARNLS Reserved ICIDCODE[5:0] Spare FAB[1:0] CHGFAULTS[1:0] CHRGSE1B CHRGSSS S USBOVI IDFACTORYI CHGENS CHGDETS USBOVS IDFACTORYS VBUSVALIDS PCI RTCRSTI SYSRSTI WDIRESTI PWRON2I PWRON1I PWRON3I TODAI 1HZI PCM RTCRSTM SYSRSTM WDIRESTM PWRON2M PWRON1M PWRON3M TODAM 1HZM PWRON2S PWRON1S PWRON3S Reserved FIN[1:0] Reserved Reserved PUMS2S[1:0] PUMS1S[1:0] ICID[2:0] CCOUT[15:0] CCFAULT MODES[1:0] REV[4:0] Reserved Reserved CCCALA CCCALDB CCDITHER RSTCC STARTCC DRM USEROFFSPI WARMEN PCCOUNTEN PCEN ONEC[14:0] COINCH EN VCOIN[2:0] BATTDETE Reserved N BPSNS[1:0] PCUTEXPB PCMAXCNT[3:0] PCCOUNT[3:0] THSEL GLBRSTENB CLK32KMC USEROFFC UEN LK PCT[7:0] SPI BITMAP 119 MC13892 IDGNDS Spare Reserved IDGNDI MC13892 Bitmap Color Coding: 31 30 29 28 27 26 25 24 23 22 Bits Reset by RESETB 21 20 19 18 Bits Reset by RTCPORB 17 16 15 Bits Reset by OFFB 14 13 Bits Without Reset 12 11 10 Bits Reloaded at Cold Start 9 8 7 6 5 4 Not Available Bits 3 2 Analog Integrated Circuit Device Data Freescale Semiconductor 15 Power R/W 0 Control 2 0 1 1 1 1 0 16 Unused R/W 0 1 0 0 0 0 0 17 Unused R/W 0 1 0 0 0 1 0 18 Memory A R/W 0 1 0 0 1 0 0 MEMA[23:0] 19 Memory B R/W 0 1 0 0 1 1 0 MEMB[23:0] 20 RTC Time R/W 0 1 0 1 0 0 0 21 RTC Alarm R/W 0 1 0 1 0 1 0 RTCDIS 22 RTC Day R/W 0 1 0 1 1 0 0 DAY[14:0] 23 RTC Day R/W 0 Alarm 1 0 1 1 1 0 DAYA[14:0] 24 Switchers 0 R/W 0 1 1 0 0 0 0 SW1HI SW1SIDMIN[3:0] SW1SIDMAX[3:0] SW1STBY[4:0] SW1DVS[4:0] SW1[4:0] 25 Unused R/W 0 1 1 0 0 1 0 SW2HI SW2SIDMIN[3:0] SW2SIDMAX[3:0] SW2STBY[4:0] SW2DVS[4:0] SW2[4:0] 26 Switchers 2 R/W 0 1 1 0 1 0 0 SW3HI SW3STBY[4:0] Spare SW3[4:0] 27 Unused R/W 0 1 1 0 1 1 0 SW4HI SW4STBY[4:0] Spare SW4[4:0] 28 Switchers 4 R/W 0 1 1 1 0 0 0 Reserve d 29 Switchers 5 R/W 0 1 1 1 0 1 0 30 Regulator R/W 0 Setting 0 1 1 1 1 0 0 31 Regulator R/W 0 Setting 1 1 1 1 1 1 0 32 Regulator R/W 1 Mode 0 0 0 0 0 0 0 33 Regulator R/W 1 Mode 1 0 0 0 0 1 0 34 Power Miscellane R/W 1 ous 0 0 0 1 0 0 STBYDLY[1:0] Reserved Reserved RTCCALMODE[1:0] Reserved CLKDRV[1:0] Reserved Reserved SPIDRV[1:0] STANDBYSE STANDBYP WDIRESET CINV RIINV Reserved Bits PWRON3DBNC[1:0] RTCCAL[4:0] PLLX[2:0] PLLEN SW2DVSSPEED[1:0] SW2UOM SW2MHMI ODE DE SW2MODE[3:0] SW4UOMOD SW4MHMIDE E SWBSTEN Spare VUSB2STBYVUSB2EN VSDMODE VSDSTBY VSDEN GPO4ADIN PWRON3RSTENPWRON2RSTEN PWRON1RSTEN RESTARTEN TODA[16:0] Reserved Spare PWRON1BDBNC[1:0] 0 TOD[16:0] Spare SWILIMB PWRON2DBNC[1:0] 1 VCAM[2:0] VGEN3 VGEN2M VGEN2STBY VGEN2EN ODE VPLLSTBY VPLLEN Spare VAUDIOST VAUDIOE VVIDEOM VVIDEOSTBY VVIDEOEN BY N ODE Spare PWGT2SPI PWGT1S EN PIEN GPO4STBY GPO4EN SIDEN SW1DVSSPEED[1:0] SW4MODE[3:0] VUSB2[1:0] Spare Reserved Spare VPLL[1:0] VDIGSTBY Reserved GPO3STBY GPO3EN SW1MODE[3:0] SW3UOMO SW3MHMIDE DE SW3MODE[3:0] VGEN[2:0] VDIG[1:0] VSD[2:0] VAUDIO[1:0] VDIGEN VCAMCONFI VCAMMOD VCAMSTBY VCAMEN G E GPO2STBY SW1UOMO SW1MHMIDE DE GPO2EN GPO1STBY GPO1EN Spare VIOHISTBY Spare Reserved VGEN[1:0] VVIDEO[1:0] VIOHIEN Reserved VGEN1MODE VGEN1STBY VGEN1EN VGEN3CONFIG VGEN3MODE VGEN3TBY VGEN3EN REGSCPEN SPI BITMAP MC13892 120 Table 111. SPI Bitmap Analog Integrated Circuit Device Data Freescale Semiconductor Table 111. SPI Bitmap MC13892 Bitmap Color Coding: 31 30 29 28 27 26 25 24 23 22 Bits Reset by RESETB 21 Unused R/W 1 0 0 0 1 1 0 36 Audio Rx 0 R/W 1 0 0 1 0 0 0 37 Audio Rx 1 R/W 1 0 0 1 0 1 0 38 Audio Tx R/W 1 0 0 1 1 0 0 39 SSI R/W 1 Network 0 0 1 1 1 0 40 Audio R/W 1 Codec 0 1 0 0 0 0 41 Audio Stereo R/W 1 DAC 0 1 0 0 1 0 42 Unused R/W 1 0 1 0 1 0 0 43 ADC 0 R/W 1 0 1 0 1 1 0 ADCBIS 0 44 ADC 1 R/W 1 0 1 1 0 0 0 ADCBIS ADONESHOT ADTRIGIGN 1 45 ADC 2 1 0 1 1 0 1 0 46 ADC 3 R/W 1 0 1 1 1 0 0 47 ADC 4 1 0 1 1 1 1 0 48 Charger 0 R/W 1 1 0 0 0 0 0 CHGAUT OVIB 49 USB 0 R/W 1 1 0 0 0 1 0 Reserve IDPUCNTRL d 50 Charger R/W 1 USB 1 1 0 0 1 0 0 51 LED R/W 1 Control 0 1 0 0 1 1 0 52 LED R/W 1 Control 1 1 0 1 0 0 0 53 LED R/W 1 Control 2 1 0 1 0 1 0 54 LED R/W 1 Control 3 1 0 1 1 0 0 R R 19 18 Spare ASC 17 16 15 ADINC2 ADINC1 CHRGRA WDIV ATOX Bits Reset by OFFB 14 13 12 TSMOD[2:0] Bits Without Reset 11 10 9 8 Reserved TSREFEN ADIN7DIV ADRESET ATO[7:0] ADD2[9:0] Bits Reloaded at Cold Start 7 6 5 4 2 1 0 BUFFEN BATICON CHRGICON LICELLCON ADSEL ADCCAL RAND ADEN ADD1[9:0] Spare Spare ADDBIS1[9:0] Spare Spare ADIN7SEL[1:0] ADA1[2:0] Spare Reserve d Not Available Bits 3 ADA2[2:0] Spare Reserved Bits TRIGMASK ICID[2:0] ADDBIS2[9:0] CYCLB CHGAUTOB Reserved CHRGREST CHGTMRRS CHRGLE PLIMDIS ART T DEN Reserved Reserved Spare LEDAD[2:0] Spare LEDADDC[5:0] Spare Spare RVRSMODE Spare Reserved Reserved Reserved Reserved Reserved Reserved PLIM[1:0] LEDADRA LEDADHI MP Spare LEDG[2:0] LEDGDC[5:0] LDEDGRA MP Spare Spare FETCTRL FETOVRD THCHKB ACLPB TREN Reserved Reserved Reserved Reserved Reserved Reserved Spare Reserved Reserved OTGSWBS TEN Reserved ID100KPU Reserved Reserved Reserved Reserved VCHRG[2:0] Reserved Reserved Reserved VUSBEN Reserved VUSBIN Spare LEDMD[2:0] LEDMDDC[5:0] LEDMDRAMP LEDMDHI Spare Spare LEDKP[2:0] LEDKPDC[5:0] LEKPDRAMP LEDKPHI Spare LEDR[2:0] LEDRDC[5:0] LDEDRRAMP LEDRPER[1:0] LEDB[2:0] LEDBDC[5:0] LDEDBRAMP LEDBPER[1:0] LEDGPER[1:0] Spare ICHRG[3:0] LEDSWBSTE N SPI BITMAP MC13892 121 35 20 Bits Reset by RTCPORB MC13892 Bitmap Color Coding: 31 30 29 28 27 26 25 24 55 Unused R/W 1 1 0 1 1 1 0 56 Unused R/W 1 1 1 0 0 0 0 57 FSL Use R/W 1 Only 1 1 0 0 1 0 58 FSL Use R/W 1 Only 1 1 0 1 0 0 59 FSL Use R/W 1 Only 1 1 0 1 1 0 60 FSL Use R/W 1 Only 1 1 1 0 0 0 61 FSL Use R/W 1 Only 1 1 1 0 1 0 62 FSL Use R/W 1 Only 1 1 1 1 0 0 63 FSL Use R/W 1 Only 1 1 1 1 1 0 23 22 Bits Reset by RESETB 21 20 19 18 Bits Reset by RTCPORB 17 16 15 Bits Reset by OFFB 14 13 12 Bits Without Reset 11 10 Bits Reloaded at Cold Start 9 8 7 6 Reserved Bits 5 4 Not Available Bits 3 2 1 0 SPI BITMAP MC13892 122 Table 111. SPI Bitmap Analog Integrated Circuit Device Data Freescale Semiconductor SPI BITMAP The 24 bit wide registers are numbered from 0 to 63, and are referenced throughout this document by register number, or representative name as given in the corresponding captions. The contents of all registers are given in the tables defined in this chapter; each table includes the following information: Name: Name of the bit. Spare bits are implemented in the design for future use, but are not assigned. Unused bits are not available in the design. Reserved bits are not implemented in the design, but are used on other PMICs. Bit #: The bit location in the register (0-23) R/W: Read / Write access and control * R is read access * W is write access * R/W is read and write access * RW1C is read and write access with write 1 to clear * RWM is read and write access while the device can modify the bit Reset: Resetting signal * RESETB, which is the same signal as the RESETB pin (so bit is held in reset as long as RESETB is low) * RTCPORB which is the reset signal of the RTC module (so bit is no longer held in reset once RTC power is good) * OFFB which is an internal signal generated when transitioning into the Off state * NONE. There is no reset signal for hardwired bits nor for the bits of which the state is determined by the power up mode settings Default: The value after reset as noted in the Default column of the SPI map. * Fixed defaults are explicitly declared as 0 or 1. * * corresponds to Read / Write bits that are initialized at startup based on power up mode settings (board level pin connections) validated at the beginning of Cold or Warm Start. Bits are subsequently SPI modifiable. * S corresponds to Read only sense bits that continuously monitor an input signal (sense signal is not latched). * L corresponds to Read only sense bits that are latched at startup. * X indicates that the state does not have an explicitly defined default value which can be specified. For instance, some bits default to a value which is dependent on the version of the IC. Description: A short description of the bit function, in some cases additional information is included The following tables are intended to give a summarized overview, for details on the bit description, see the individual chapters. Table 112. Register 0, Interrupt Status 0 R/W Reset ADCDONEI Name Bit # 0 RW1C RESETB 0 ADC has finished requested conversions ADCBISDONEI 1 RW1C RESETB 0 ADCBIS has finished requested conversions TSI 2 RW1C RESETB 0 Touch screen wake-up VBUSVALIDI 3 RW1C OFFB 0 VBUSVALID detect IDFACTORYI 4 RW1C RESETB 0 ID factory mode detect USBOVI 5 RW1C RTCPORB 0 USB over-voltage detection CHGDETI 6 RW1C OFFB 0 Charger attach CHGFAULTI 7 RW1C RTCPORB 0 Charger fault detection CHGREVI 8 RW1C RESETB 0 Charger path reverse current CHGSHORTI 9 RW1C RESETB 0 Charger path short circuit CCCVI 10 RW1C RESETB 0 Charger path CC / CV transition detect CHGCURRI 11 RW1C RESETB 0 Charge current below threshold warning BPONI 12 RW1C OFFB 0 BP turn on threshold LOBATLI 13 RW1C RESETB 0 Low battery low threshold warning LOBATHI 14 RW1C RESETB 0 Low battery high threshold warning Reserved 15 R 0 For future use BVALIDI 16 RW1C 0 USB B-session valid interrupt Reserved 17 R 0 For future use Reserved 18 R 0 For future use IDFLOATI 19 RW1C RESETB 0 USB ID float detect IDGNDI 20 RW1C RESETB 0 USB ID ground detect OFFB Default Description MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 123 SPI BITMAP Table 112. Register 0, Interrupt Status 0 Name Bit # R/W Reset CHRGSE1BI 21 RW1C RESETB Default Reserved 22 Reserved 23 Description 0 Wall Charger detect R 0 For future use R 0 For future use Table 113. Register 1, Interrupt Mask 0 Name Bit # R/W Reset Default Description ADCDONEM 0 R/W RESETB 1 ADCDONEI mask bit ADCBISDONEM 1 R/W RESETB 1 ADCBISDONEI mask bit TSM 2 R/W RESETB 1 TSI mask bit VBUSVALIDM 3 R/W OFFB 1 VBUSVALIDI mask bit IDFACTORYM 4 R/W RESETB 1 ID factory mask bit USBOVM 5 R/W RTCPORB 1 USBOVI mask bit CHGDETM 6 R/W OFFB 1 CHGDETI mask bit CHGFAULTM 7 R/W RTCPORB 1 CHGFAULTI mask bit CHGREVM 8 R/W RESETB 1 CHGREVI mask bit CHGSHORTM 9 R/W RESETB 1 CHGSHORTI mask bit CCCVM 10 R/W RESETB 1 CCCV mask bit CHGCURRM 11 R/W RESETB 1 CHGCURRI mask bit BPONM 12 R/W OFFB 1 BPONI mask bit LOBATLM 13 R/W RESETB 1 LOBATLI mask bit LOBATHM 14 R/W RESETB 1 LOBATHI mask bit Reserved 15 R 1 For future use BVALIDM 16 R/W 1 BVALIDI mask bit Reserved 17 R 1 For future use Reserved 18 R 1 For future use IDFLOATM 19 R/W RESETB 1 IDFLOATI mask bit IDGNDM 20 R/W RESETB 1 IDGNDI mask bit CHRGSE1BM 21 R/W RESETB 1 Wall Charger mask bit Reserved 22 R 1 For future use Reserved 23 R 1 For future use OFFB Table 114. Register 2, Interrupt Sense 0 Name Bit # R/W Reset Default Description Unused 0 R 0 Not available Unused 1 R 0 Not available Unused 2 R 0 Not available VBUSVALIDS 3 R NONE S VBUSVALIDI sense bit IDFACTORYS 4 R NONE S ID factory sense bit USBOVS 5 R NONE S USBOVI sense bit CHGDETS 6 R NONE S CHGDETI sense bit CHGENS 7 R NONE 0 Charger enable sense bit CHGFAULTS0 8 R NONE S CHGREVI sense bit CHGFAULTS1 9 R NONE S CHRGFAULT sense bit 0 CCCVS 10 R NONE S CHRGFAULT sense bit 1 CHGCURRS 11 R NONE S CHGCURRI sense bit BPONS 12 R NONE S BPONI sense bit LOBATLS 13 R NONE S LOBATLI sense bit LOBATHS 14 R NONE S LOBATHI sense bit MC13892 124 Analog Integrated Circuit Device Data Freescale Semiconductor SPI BITMAP Table 114. Register 2, Interrupt Sense 0 Name Bit # R/W Reset Default Description Reserved BVALIDS 15 16 R R NONE 0 S For future use USB B-session valid sense Reserved 17 R 0 For future use Reserved 18 R 0 For future use IDFLOATS 19 R NONE S ID float sense bit IDGNDS 20 R NONE S ID ground sense bit Reserved 21 R 0 For future use Reserved 22 R 0 For future use Reserved 23 R 0 For future use Table 115. Register 3, Interrupt Status 1 Name Bit # R/W Reset Default Description 1HZI 0 RW1C RTCPORB 0 1.0 Hz time tick TODAI 1 RW1C RTCPORB 0 Time of day alarm PWRON3I 2 RW1C OFFB 0 PWRON3 event PWRON1I 3 RW1C OFFB 0 PWRON1 event PWRON2I 4 RW1C OFFB 0 PWRON2 event WDIRESETI 5 RW1C RTCPORB 0 WDI system reset event SYSRSTI 6 RW1C RTCPORB 0 PWRON system reset event RTCRSTI 7 RW1C RTCPORB 1 RTC reset event PCI 8 RW1C OFFB 0 Power cut event WARMI 9 RW1C RTCPORB 0 Warm start event MEMHLDI 10 RW1C RTCPORB 0 Memory hold event LPBI 11 RW1C RTCPORB 0 Low-power USB boot detection THWARNLI 12 RW1C RESETB 0 Thermal warning low threshold THWARNHI 13 RW1C RESETB 0 Thermal warning high threshold CLKI 14 RW1C RESETB 0 Clock source change Spare 15 RW1C RESETB 0 For future use SCPI 16 RW1C RESETB 0 Short-circuit protection trip detection Reserved 17 R 0 For future use Reserved 18 R 0 For future use Reserved 19 R 0 For future use Reserved 20 R 0 For future use Unused 21 R 0 Not available BATTDETBI 22 RW1C RESETB 0 Battery removal detect Spare 23 RW1C RESETB 0 For future use Table 116. Register 4, Interrupt Mask 1 Name Bit # R/W Reset Default Description 1HZM 0 R/W RTCPORB 1 1HZI mask bit TODAM 1 R/W RTCPORB 1 TODAI mask bit PWRON3M 2 R/W OFFB 1 PWRON3 mask bit PWRON1M 3 R/W OFFB 1 PWRON1 mask bit PWRON2M 4 R/W OFFB 1 PWRON2 mask bit WDIRESETM 5 R/W RTCPORB 1 WDIRESETI mask bit SYSRSTM 6 R/W RTCPORB 1 SYSRSTI mask bit RTCRSTM 7 R/W RTCPORB 1 RTCRSTI mask bit PCM 8 R/W OFFB 1 PCI mask bit MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 125 SPI BITMAP Table 116. Register 4, Interrupt Mask 1 Name Bit # R/W Reset Default Description WARMM 9 R/W RTCPORB 1 WARMI mask bit MEMHLDM 10 R/W RTCPORB 1 MEMHLDI mask bit LPBM 11 R/W RTCPORB 0 Low-power USB detect mask bit THWARNLM 12 R/W RESETB 1 THWARNLI mask bit THWARNHM 13 R/W RESETB 1 THWARNHI mask bit CLKM 14 R/W RESETB 1 CLKI mask bit Spare 15 R/W RESETB 1 For future use SCPM 16 R/W RESETB 1 Short-circuit protection trip mask bit Reserved 17 R 1 For future use Reserved 18 R 1 For future use Reserved 19 R 1 For future use Reserved 20 R 1 For future use Unused 21 R 1 Not available BATTDETBM 22 R/W RESETB 1 Battery detect removal mask bit Spare 23 R/W RESETB 1 For future use Table 117. Register 5, Interrupt Sense 1 Name Bit # R/W Reset Default Description Unused 0 R 0 Not available Unused 1 R 0 Not available PWRON3S 2 R NONE S PWRON3I sense bit PWRON1S 3 R NONE S PWRON1I sense bit PWRON2S 4 R NONE S PWRON2I sense bit Unused 5 R 0 Not available Unused 6 R 0 Not available Unused 7 R 0 Not available Unused 8 R 0 Not available Unused 9 R 0 Not available Unused 10 R 0 Not available LPBS 11 R NONE 0 Low-power USB boot sense bit THWARNLS 12 R NONE S THWARNLI sense bit THWARNHS 13 R NONE S THWARNHI sense bit CLKS 14 R NONE S CLKI sense bit Spare 15 R NONE 0 For future use Unused 16 R 0 Not available Reserved 17 R 0 For future use Reserved 18 R 0 For future use Reserved 19 R 0 For future use Reserved 20 R 0 For future use Unused 21 R 0 Not available BATTDETBS 22 R NONE S Battery removal detect sense bit Spare 23 R NONE 0 For future use Table 118. Register 6, Power Up Mode Sense Name Bit # R/W Reset Default MODES0 0 R NONE S IMODES1 1 R NONE S Description MODE sense decode MC13892 126 Analog Integrated Circuit Device Data Freescale Semiconductor SPI BITMAP Table 118. Register 6, Power Up Mode Sense Name Bit # R/W Reset Default Description PUMS1S0 2 R NONE L PUMS1S1 3 R NONE L PUMS2S0 4 R NONE L PUMS2S1 5 R NONE L Reserved 6 R 0 For future use Reserved 7 R 0 For future use Reserved 8 R 0 For future use CHRGSSS (1) 9 R NONE L Charger Serial/Single mode sense CHRGSE1BS 10 R NONE S CHRGSE1BS sense bit Unused 11 R 0 Not available Spare 12 R 0 For future use Unused 13 R 0 Not available Reserved 14 R 0 For future use Unused 15 R 0 Not available Unused 16 R 0 Not available Unused 17 R 0 Not available Spare 18 R NONE 0 For future use Spare 19 R NONE 0 For future use Reserved 20 R 0 For future use Reserved 21 R 0 For future use Spare 22 R NONE 0 For future use Spare 23 R NONE 0 For future use NONE PUMS1 state PUMS2 state Notes 95. CHRGSSS will latch an updated sense value when the charger is enabled. Table 119. Register 7, Identification Name Bit # R/W Reset Default Description REV0 0 R NONE X REV1 1 R NONE X REV2 2 R NONE X REV3 3 R NONE X REV4 4 R NONE X Unused 5 R ICID0 6 R NONE 1 ICID1 7 R NONE 1 ICID2 8 R NONE 1 FIN0 9 R NONE X FIN1 10 R NONE X FAB0 11 R NONE X FAB1 12 R NONE X ICIDCODE0 13 R NONE 0 ICIDCODE1 14 R NONE 1 ICIDCODE2 15 R NONE 0 ICIDCODE3 16 R NONE 0 ICIDCODE4 17 R NONE 0 ICIDCODE5 18 R NONE 0 Unused 19 R 0 Not available Unused 20 R 0 Not available Unused 21 R 0 Not available 0 Revision Not available Generation ID MC13892 fin version MC13892 fab identifier IC ID Within generation MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 127 SPI BITMAP Table 119. Register 7, Identification Bit # R/W Unused Name 22 R Reset Default 0 Not available Description Unused 23 R 0 Not available Table 120. Register 8, Unused Name Bit # Unused 23-0 R/W Reset R Default 0 Description Not available Table 121. Register 9, ACC 0 Name Bit # R/W Reset Default Description STARTCC 0 R/W RTCPORB 0 1 = Run, 0=Stop RSTCC 1 RWC RTCPORB 0 1 = Reset, self clearing CCDITHER 2 R/W RTCPORB 0 1 = ACC Dithering enabled, 0=ACC Dithering disabled CCCALDB 3 R/W RTCPORB 0 1 = Disable Digital Offset Cancellation CCCALA 4 R/W RTCPORB 0 1 = Enable Analog Offset Calibration Mode Reserved 5 R 0 Reserved for future use for scaler Reserved 6 R 0 Reserved for future use (for scaler) CCFAULT 7 R/W RTCPORB 0 1 = CCOUT contents no longer valid CCOUT0 8 R RTCPORB 0 CCOUT1 9 R RTCPORB 0 CCOUT2 10 R RTCPORB 0 CCOUT3 11 R RTCPORB 0 CCOUT4 12 R RTCPORB 0 CCOUT5 13 R RTCPORB 0 CCOUT6 14 R RTCPORB 0 CCOUT7 15 R RTCPORB 0 CCOUT8 16 R RTCPORB 0 CCOUT9 17 R RTCPORB 0 CCOUT10 18 R RTCPORB 0 CCOUT11 19 R RTCPORB 0 CCOUT12 20 R RTCPORB 0 CCOUT13 21 R RTCPORB 0 CCOUT14 22 R RTCPORB 0 CCOUT15 23 R RTCPORB 0 Coulomb Counter MC13892 128 Analog Integrated Circuit Device Data Freescale Semiconductor SPI BITMAP Table 122. Register 10, ACC 1 Name Bit # R/W Reset Default Description ONEC0 0 R RTCPORB 1 ONEC1 1 R RTCPORB 0 ONEC2 2 R RTCPORB 0 ONEC3 3 R RTCPORB 0 ONEC4 4 R RTCPORB 0 ONEC5 5 R RTCPORB 0 ONEC6 6 R RTCPORB 0 ONEC7 7 R RTCPORB 0 ONEC8 8 R RTCPORB 0 ONEC9 9 R RTCPORB 0 ONEC10 10 R RTCPORB 0 ONEC11 11 R RTCPORB 0 ONEC12 12 R RTCPORB 0 ONEC13 13 R RTCPORB 0 ONEC14 14 R RTCPORB 0 Unused 15 R 0 Not available Unused 16 R 0 Not available Unused 17 R 0 Not available Unused 18 R 0 Not available Unused 19 R 0 Not available Unused 20 R 0 Not available Unused 21 R 0 Not available Unused 22 R 0 Not available Unused 23 R 0 Not available Accumulated Current Counter output Table 123. Register 11, Unused Name Bit # Unused R/W 23-0 Reset Default R 0 Description Not available Table 124. Register 12, Unused Name Bit # Unused R/W 23-0 Reset Default R 0 Description Not available Table 125. Register 13, Power Control 0 Name Bit # R/W Reset Default Description PCEN 0 R/W RTCPORB 0 Power cut enable PCCOUNTEN 1 R/W RTCPORB 0 Power cut counter enable WARMEN 2 R/W RTCPORB 0 Warm start enable USEROFFSPI 3 R/W RESETB 0 SPI command for entering user off modes DRM 4 R/W RTCPORB 0 Keeps VSRTC and CLK32KMCU on for all states USEROFFCLK 5 R/W RTCPORB 0 Keeps the CLK32KMCU active during user off CLK32KMCUEN 6 R/W RTCPORB 1 Enables the CLK32KMCU GLBRSTENB(96) 7 R/W RTCPORB 0 Global Reset Function enabled on the PWRON3 pin THSEL 8 R/W RESETB 0 Thermal protection threshold select PCUTEXPB 9 RWM RTCPORB 0 PCUTEXPB=1 at a startup event indicates that PCUT timer did not expire (assuming it was set to 1 after booting) Unused 10 R 0 Not available Unused 11 R 0 Not available MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 129 SPI BITMAP Table 125. Register 13, Power Control 0 Bit # R/W Unused Name 12 R Reset Default 0 Not available Description Unused 13 R 0 Not available Unused 14 R 0 Not available Unused 15 R 0 Not available BPSNS0 16 R/W RTCPORB 0 BPSNS1 17 R/W RTCPORB 0 Reserved 18 R 0 For future use BATTDETEN 19 R/W RTCPORB 0 Enables battery detect function VCOIN0 20 R/W RTCPORB 0 VCOIN1 21 R/W RTCPORB 0 VCOIN2 22 R/W RTCPORB 0 COINCHEN 23 R/W RTCPORB 0 Coin cell charger voltage setting Coin cell charger enable Notes 96. MC13892A/C versions global reset is active low (GLBRSTENB = 0) MC13892B/D versions global reset is active high (GLBRSTENB = 1) Table 126. Register 14, Power Control 1 Name Bit # R/W Reset Default Description PCT0 0 R/W RTCPORB 0 PCT1 1 R/W RTCPORB 0 PCT2 2 R/W RTCPORB 0 PCT3 3 R/W RTCPORB 0 PCT4 4 R/W RTCPORB 0 PCT5 5 R/W RTCPORB 0 PCT6 6 R/W RTCPORB 0 PCT7 7 R/W RTCPORB 0 PCCOUNT0 8 R/W RTCPORB 0 PCCOUNT1 9 R/W RTCPORB 0 PCCOUNT2 10 R/W RTCPORB 0 PCCOUNT3 11 R/W RTCPORB 0 PCMAXCNT0 12 R/W RTCPORB 0 PCMAXCNT1 13 R/W RTCPORB 0 PCMAXCNT2 14 R/W RTCPORB 0 PCMAXCNT3 15 R/W RTCPORB 0 Unused 16 R 0 Not available Unused 17 R 0 Not available Unused 18 R 0 Not available Unused 19 R 0 Not available Unused 20 R 0 Not available Unused 21 R 0 Not available Unused 22 R 0 Not available Unused 23 R 0 Not available Power cut timer Power cut counter Maximum allowed number of power cuts Table 127. Register 15, Power Control 2 Name Bit # R/W Reset Default Description RESTARTEN 0 R/W RTCPORB 0 Enables automatic restart after a system reset PWRON1RSTEN 1 R/W RTCPORB 0 Enables system reset on PWRON1 pin PWRON2RSTEN 2 R/W RTCPORB 0 Enables system reset on PWRON2 pin PWRON3RSTEN 3 R/W RTCPORB 0 Enables system reset on PWRON3 pin MC13892 130 Analog Integrated Circuit Device Data Freescale Semiconductor SPI BITMAP Table 127. Register 15, Power Control 2 Name Bit # R/W Reset Default Description PWRON1DBNC0 4 R/W RTCPORB 0 PWRON1DBNC1 5 R/W RTCPORB 0 PWRON2DBNC0 6 R/W RTCPORB 0 PWRON2DBNC1 7 R/W RTCPORB 0 PWRON3DBNC0 8 R/W RTCPORB 0 PWRON3DBNC1 9 R/W RTCPORB 0 STANDBYINV 10 R/W RTCPORB 0 If set then STANDBY is interpreted as active low STANDBYSECINV 11 R/W RTCPORB 0 If set then STANDBYSEC is interpreted as active low WDIRESET 12 R/W RESETB 0 Enables system reset through WDI SPIDRV0 13 R/W RTCPORB 0 SPIDRV1 14 R/W RTCPORB 0 Reserved 15 R 0 Reserved 16 R 0 CLK32KDRV0 17 R/W RTCPORB 0 CLK32KDRV1 18 R/W RTCPORB 0 Reserved 19 R 0 Reserved 20 R 0 Reserved 21 R 0 STBYDLY0 22 R/W RESETB 1 STBYDLY1 23 R/W RESETB 0 Reset Default Sets debounce time on PWRON1 pin Sets debounce time on PWRON2 pin Sets debounce time on PWRON3 pin SPI drive strength For future use CLK32K and CLK32KMCU drive strength (master control bits) For future use Standby delay control Table 128. Register 16, Unused Name Unused Bit # R/W 23-0 R 0 Description Not available Table 129. Register 17, Unused Name Unused Bit # 23-0 R/W R Reset Default 0 Description Not available MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 131 SPI BITMAP Table 130. Register 18, Memory A Name Bit # R/W Reset Default MEMA0 0 R/W RTCPORB 0 MEMA1 1 R/W RTCPORB 0 MEMA2 2 R/W RTCPORB 0 MEMA3 3 R/W RTCPORB 0 MEMA4 4 R/W RTCPORB 0 MEMA5 5 R/W RTCPORB 0 MEMA6 6 R/W RTCPORB 0 MEMA7 7 R/W RTCPORB 0 MEMA8 8 R/W RTCPORB 0 MEMA9 9 R/W RTCPORB 0 MEMA10 10 R/W RTCPORB 0 MEMA11 11 R/W RTCPORB 0 MEMA12 12 R/W RTCPORB 0 MEMA13 13 R/W RTCPORB 0 MEMA14 14 R/W RTCPORB 0 MEMA15 15 R/W RTCPORB 0 MEMA16 16 R/W RTCPORB 0 MEMA17 17 R/W RTCPORB 0 MEMA18 18 R/W RTCPORB 0 MEMA19 19 R/W RTCPORB 0 MEMA20 20 R/W RTCPORB 0 MEMA21 21 R/W RTCPORB 0 MEMA22 22 R/W RTCPORB 0 MEMA23 23 R/W RTCPORB 0 Description Backup memory A MC13892 132 Analog Integrated Circuit Device Data Freescale Semiconductor SPI BITMAP Table 131. Register 19, Memory B Name Bit # R/W Reset Default MEMB0 0 R/W RTCPORB 0 MEMB1 1 R/W RTCPORB 0 MEMB2 2 R/W RTCPORB 0 MEMB3 3 R/W RTCPORB 0 MEMB4 4 R/W RTCPORB 0 MEMB5 5 R/W RTCPORB 0 MEMB6 6 R/W RTCPORB 0 MEMB7 7 R/W RTCPORB 0 MEMB8 8 R/W RTCPORB 0 MEMB9 9 R/W RTCPORB 0 MEMB10 10 R/W RTCPORB 0 MEMB11 11 R/W RTCPORB 0 MEMB12 12 R/W RTCPORB 0 MEMB13 13 R/W RTCPORB 0 MEMB14 14 R/W RTCPORB 0 MEMB15 15 R/W RTCPORB 0 MEMB16 16 R/W RTCPORB 0 MEMB17 17 R/W RTCPORB 0 MEMB18 18 R/W RTCPORB 0 MEMB19 19 R/W RTCPORB 0 MEMB20 20 R/W RTCPORB 0 MEMB21 21 R/W RTCPORB 0 MEMB22 22 R/W RTCPORB 0 MEMB23 23 R/W RTCPORB 0 Description Backup memory B Table 132. Register 20, RTC Time Name Bit # R/W Reset Default TOD0 0 R/W RTCPORB 0 TOD1 1 R/W RTCPORB 0 TOD2 2 R/W RTCPORB 0 TOD3 3 R/W RTCPORB 0 TOD4 4 R/W RTCPORB 0 TOD5 5 R/W RTCPORB 0 TOD6 6 R/W RTCPORB 0 TOD7 7 R/W RTCPORB 0 TOD8 8 R/W RTCPORB 0 TOD9 9 R/W RTCPORB 0 TOD10 10 R/W RTCPORB 0 TOD11 11 R/W RTCPORB 0 TOD12 12 R/W RTCPORB 0 TOD13 13 R/W RTCPORB 0 TOD14 14 R/W RTCPORB 0 TOD15 15 R/W RTCPORB 0 TOD16 16 R/W RTCPORB 0 RTCCAL0 17 R/W RTCPORB 0 RTCCAL1 18 R/W RTCPORB 0 RTCCAL2 19 R/W RTCPORB 0 RTCCAL3 20 R/W RTCPORB 0 RTCCAL4 21 R/W RTCPORB 0 Description Time of day counter RTC calibration count MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 133 SPI BITMAP Table 132. Register 20, RTC Time Name Bit # R/W Reset Default RTCCALMODE0 22 R/W RTCPORB 0 RTCCALMODE1 23 R/W RTCPORB 0 Description RTC calibration mode Table 133. Register 21, RTC Alarm Name Bit # R/W Reset Default TODA0 0 R/W RTCPORB 1 TODA1 1 R/W RTCPORB 1 TODA2 2 R/W RTCPORB 1 TODA3 3 R/W RTCPORB 1 TODA4 4 R/W RTCPORB 1 TODA5 5 R/W RTCPORB 1 TODA6 6 R/W RTCPORB 1 TODA7 7 R/W RTCPORB 1 TODA8 8 R/W RTCPORB 1 TODA9 9 R/W RTCPORB 1 TODA10 10 R/W RTCPORB 1 TODA11 11 R/W RTCPORB 1 TODA12 12 R/W RTCPORB 1 TODA13 13 R/W RTCPORB 1 TODA14 14 R/W RTCPORB 1 TODA15 15 R/W RTCPORB 1 TODA16 16 R/W RTCPORB 1 Spare 17 R/W RTCPORB 0 Spare 18 R/W RTCPORB 0 Spare 19 R/W RTCPORB 0 Spare 20 R/W RTCPORB 0 Spare 21 R/W RTCPORB 0 Spare 22 R/W RTCPORB 0 RTCDIS 23 R/W RTCPORB 0 Description Time of day alarm For future use Disable RTC Table 134. Register 22, RTC Day Name Bit # R/W Reset Default DAY0 0 R/W RTCPORB 0 DAY1 1 R/W RTCPORB 0 DAY2 2 R/W RTCPORB 0 DAY3 3 R/W RTCPORB 0 DAY4 4 R/W RTCPORB 0 DAY5 5 R/W RTCPORB 0 DAY6 6 R/W RTCPORB 0 DAY7 7 R/W RTCPORB 0 DAY8 8 R/W RTCPORB 0 DAY9 9 R/W RTCPORB 0 DAY10 10 R/W RTCPORB 0 DAY11 11 R/W RTCPORB 0 DAY12 12 R/W RTCPORB 0 DAY13 13 R/W RTCPORB 0 DAY14 14 R/W RTCPORB 0 Description Day counter MC13892 134 Analog Integrated Circuit Device Data Freescale Semiconductor SPI BITMAP Table 134. Register 22, RTC Day Bit # R/W Unused Name 15 R Reset Default 0 Unused 16 R 0 Unused 17 R 0 Unused 18 R 0 Unused 19 R 0 Unused 20 R 0 Unused 21 R 0 Unused 22 R 0 Unused 23 R 0 Description Not available Table 135. Register 23, RTC Day Alarm Name Bit # R/W Reset Default DAYA0 0 R/W RTCPORB 1 DAYA1 1 R/W RTCPORB 1 DAYA2 2 R/W RTCPORB 1 DAYA3 3 R/W RTCPORB 1 DAYA4 4 R/W RTCPORB 1 DAYA5 5 R/W RTCPORB 1 DAYA6 6 R/W RTCPORB 1 DAYA7 7 R/W RTCPORB 1 DAYA8 8 R/W RTCPORB 1 DAYA9 9 R/W RTCPORB 1 DAYA10 10 R/W RTCPORB 1 DAYA11 11 R/W RTCPORB 1 DAYA12 12 R/W RTCPORB 1 DAYA13 13 R/W RTCPORB 1 DAYA14 14 R/W RTCPORB 1 Unused 15 R 0 Unused 16 R 0 Unused 17 R 0 Unused 18 R 0 Unused 19 R 0 Unused 20 R 0 Unused 21 R 0 Unused 22 R 0 Unused 23 R 0 Description Day alarm Not available Table 136. Register 24, Switchers 0 Name Bit # R/W Reset Default SW10 0 R/W NONE * SW11 1 R/W NONE * SW12 2 R/W NONE * SW13 3 R/W NONE * SW14 4 R/W NONE * Description SW1 setting in normal mode MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 135 SPI BITMAP Table 136. Register 24, Switchers 0 Name Bit # R/W Reset Default SW1DVS0 5 R/W NONE * SW1DVS1 6 R/W NONE * SW1DVS2 7 R/W NONE * SW1DVS3 8 R/W NONE * SW1DVS4 9 R/W NONE * SW1STBY0 10 R/W NONE * SW1STBY1 11 R/W NONE * SW1STBY2 12 R/W NONE * SW1STBY3 13 R/W NONE * SW1STBY4 14 R/W NONE * SW1SIDMAX0 15 R/W RESETB 0 SW1SIDMAX1 16 R/W RESETB 1 SW1SIDMAX2 17 R/W RESETB 0 SW1SIDMAX3 18 R/W RESETB 1 SW1SIDMIN0 19 R/W RESETB 0 SW1SIDMIN1 20 R/W RESETB 0 SW1SIDMIN2 21 R/W RESETB 0 SW1SIDMIN3 22 R/W RESETB 1 SW1HI 23 R/W NONE * Description SW1 setting in DVS mode SW1 setting in Standby mode SW1 SID mode maximum level SW1 SID mode minimum level (leading 0 implied) SW1 output range selection Table 137. Register 25, Switchers 1 Name Bit # R/W Reset Default SW20 0 R/W NONE * SW21 1 R/W NONE * SW22 2 R/W NONE * SW23 3 R/W NONE * SW24 4 R/W NONE * SW2DVS0 5 R/W NONE * SW2DVS1 6 R/W NONE * SW2DVS2 7 R/W NONE * SW2DVS3 8 R/W NONE * SW2DVS4 9 R/W NONE * SW2STBY0 10 R/W NONE * SW2STBY1 11 R/W NONE * SW2STBY2 12 R/W NONE * SW2STBY3 13 R/W NONE * SW2STBY4 14 R/W NONE * SW2SIDMAX0 15 R/W RESETB 0 SW2SIDMAX1 16 R/W RESETB 1 SW2SIDMAX2 17 R/W RESETB 0 SW2SIDMAX3 18 R/W RESETB 1 SW2SIDMIN0 19 R/W RESETB 0 SW2SIDMIN1 20 R/W RESETB 0 SW2SIDMIN2 21 R/W RESETB 0 SW2SIDMIN3 22 R/W RESETB 1 SW2HI 23 R/W NONE * Description SW2 setting in normal mode SW2 setting in DVS mode SW2 setting in Standby mode SW2 SID mode maximum level SW2 SID mode minimum level (leading 0 implied) SW2 output range selection MC13892 136 Analog Integrated Circuit Device Data Freescale Semiconductor SPI BITMAP Table 138. Register 26, Switchers 2 Name Bit # R/W Reset Default SW30 0 R/W NONE * SW31 1 R/W NONE * SW32 2 R/W NONE * SW33 3 R/W NONE * SW34 4 R/W NONE * Spare 5 R/W NONE * Spare 6 R/W NONE * Spare 7 R/W NONE * Spare 8 R/W NONE * Spare 9 R/W NONE * SW3STBY0 10 R/W NONE * SW3STBY1 11 R/W NONE * SW3STBY2 12 R/W NONE * SW3STBY3 13 R/W NONE * SW3STBY4 14 R/W NONE Unused 15 R 0 Unused 16 R 0 Unused 17 R 0 Unused 18 R 0 Unused 19 R 0 Unused 20 R 0 Unused 21 R 0 Reserved 22 R SW3HI 23 R/W NONE Description SW3 setting in normal mode For future use SW3 setting in Standby mode * Not available 0 For future use * SW3 output range selection Table 139. Register 27, Switchers 3 Name Bit # R/W Reset Default SW40 0 R/W NONE * SW41 1 R/W NONE * SW42 2 R/W NONE * SW43 3 R/W NONE * SW44 4 R/W NONE * Spare 5 R/W NONE * Spare 6 R/W NONE * Spare 7 R/W NONE * Spare 8 R/W NONE * Spare 9 R/W NONE * SW4STBY0 10 R/W NONE * SW4STBY1 11 R/W NONE * SW4STBY2 12 R/W NONE * SW4STBY3 13 R/W NONE * SW4STBY4 14 R/W NONE * Description SW4 setting in normal mode For future use SW4 setting in Standby mode MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 137 SPI BITMAP Table 139. Register 27, Switchers 3 Bit # R/W Unused Name 15 R Reset Default 0 Unused 16 R 0 Unused 17 R 0 Unused 18 R 0 Unused 19 R 0 Unused 20 R 0 Unused 21 R 0 Unused 22 R SW4HI 23 R/W Description Not available 0 NONE * SW4 output range selection Table 140. Register 28, Switchers 4 Name Bit # R/W Reset Default Description SW1MODE0 0 R/W RESETB 0 SW1MODE1 1 R/W RESETB 1 SW1MODE2 2 R/W RESETB 0 SW1MODE3 3 R/W RESETB 1 SW1MHMODE 4 R/W OFFB 0 SW1 Memory Hold mode SW1UOMODE 5 R/W OFFB 0 SW1 User Off mode SW1DVSSPEED0 6 R/W RESETB 1 SW1DVSSPEED1 7 R/W RESETB 0 SIDEN 8 R/W RESETB 0 SID mode enable Reserved 9 R 0 For future use SW2MODE0 10 R/W RESETB 0 SW2MODE1 11 R/W RESETB 1 SW2MODE2 12 R/W RESETB 0 SW2MODE3 13 R/W RESETB 1 SW2MHMODE 14 R/W OFFB 0 SW2 Memory Hold mode SW2UOMODE 15 R/W OFFB 0 SW2 User Off mode SW2DVSSPEED0 16 R/W RESETB 1 SW2DVSSPEED1 17 R/W RESETB 0 PLLEN 18 R/W RESETB 0 PLLX0 19 R/W RESETB 0 PLLX1 20 R/W RESETB 0 PLLX2 21 R/W RESETB 1 SWILIMB 22 R/W RESETB 0 Switcher current limit disable Reserved 23 R 0 For future use SW1 operating mode SW1 DVS speed setting SW2 operating mode SW2 DVS speed setting Switcher PLL enable Switcher PLL multiplication factor Notes 97. SWxMODE[3:0] bits will be reset to their default values by the startup sequencer based on PUMS settings. An enabled switcher will default to PWM mode (no pulse skipping) for both Normal and Standby operation. Table 141. Register 29, Switchers 5 Name Bit # R/W Reset Default Description SW3MODE0 0 R/W RESETB 0 SW3MODE1 1 R/W RESETB 1 SW3MODE2 2 R/W RESETB 0 SW3MODE3 3 R/W RESETB 1 SW3MHMODE 4 R/W OFFB 0 SW3 Memory Hold mode SW3UOMODE 5 R/W OFFB 0 SW3 User Off mode SW3 operating mode MC13892 138 Analog Integrated Circuit Device Data Freescale Semiconductor SPI BITMAP Table 141. Register 29, Switchers 5 Name Bit # R/W Reset Default Description Unused 6 R 0 Unused 7 R 0 SW4MODE0 8 R/W RESETB 0 SW4MODE1 9 R/W RESETB 1 SW4MODE2 10 R/W RESETB 0 SW4MODE3 11 R/W RESETB 1 SW4MHMODE 12 R/W OFFB 0 SW4 Memory Hold mode SW4UOMODE 13 R/W OFFB 0 SW4 User Off mode Unused 14 R 0 Unused 15 R 0 Unused 16 R 0 Unused 17 R 0 Unused 18 R 0 Unused 19 R SWBSTEN 20 R/W Unused 21 R 0 Unused 22 R 0 Unused 23 R 0 Not available SW4 operating mode Not available 0 NONE * SWBST enable Not available Notes 98. SWxMODE[3:0] bits will be reset to their default values by the startup sequencer based on PUMS settings. An enabled switcher will default to PWM mode (no pulse skipping) for both Normal and Standby operation. Table 142. Register 30, Regulator Setting 0 Name Bit # R/W Reset Default Description VGEN10 0 R/W RESETB 0 VGEN11 1 R/W RESETB 0 Unused 2 R 0 Unused 3 R 0 VDIG0 4 R/W NONE * VDIG1 5 R/W NONE * VGEN20 6 R/W NONE * VGEN21 7 R/W NONE * VGEN22 8 R/W NONE * VPLL0 9 R/W NONE * VPLL1 10 R/W NONE * VUSB20 11 R/W NONE * VUSB21 12 R/W NONE * Unused 13 R VGEN3 14 R/W Unused 15 R VCAM0 16 R/W RESETB 0 VCAM1 17 R/W RESETB 1 Spare 18 R/W RESETB 0 For future use Unused 19 R 0 Not available Unused 20 R 0 Not available Unused 21 R 0 Not available Unused 22 R 0 Not available Unused 23 R 0 Not available RESETB VGEN1 setting Not available VDIG setting VGEN2 setting VPLL setting VUSB2 setting 0 Not available 1 VGEN3 setting 0 Not available VCAM setting MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 139 SPI BITMAP Table 143. Register 31, Regulator Setting 1 Name Bit # R/W Reset Default Reserved 0 R 0 Reserved 1 R 0 VVIDEO0 2 R/W RESETB 0 VVIDEO1 3 R/W RESETB 1 VAUDIO0 4 R/W RESETB 1 VAUDIO1 5 R/W RESETB 0 VSD10 6 R/W RESETB 1 VSD11 7 R/W RESETB 1 VSD12 8 R/W RESETB 1 Unused 9 R 0 Unused 10 R 0 Unused 11 R 0 Unused 12 R 0 Unused 13 R 0 Unused 14 R 0 Unused 15 R 0 Unused 16 R 0 Unused 17 R 0 Unused 18 R 0 Unused 19 R 0 Unused 20 R 0 Unused 21 R 0 Unused 22 R 0 Unused 23 R 0 Description For future use VVIDEO setting VAUDIO setting VSD setting Not available Table 144. Register 32, Regulator Mode 0 Name Bit # R/W Reset Default Description VGEN1EN 0 R/W RESETB 0 VGEN1 enable VGEN1STBY 1 R/W RESETB 0 VGEN1 controlled by standby VGEN1MODE 2 R/W RESETB 0 VGEN1 operating mode VIOHIEN 3 R/W NONE * VIOHI enable VIOHISTBY 4 R/W RESETB 0 VIOHI controlled by standby Spare 5 R/W RESETB 0 For future use Unused 6 R 0 Not available Unused 7 R 0 Not available Unused 8 R 0 Not available VDIGEN 9 R/W NONE * VDIG enable VDIGSTBY 10 R/W RESETB 0 VDIG controlled by standby Spare 11 R/W RESETB 0 For future use VGEN2EN 12 R/W NONE * VGEN2 enable VGEN2STBY 13 R/W RESETB 0 VGEN2 controlled by standby VGEN2MODE 14 R/W RESETB 0 VGEN2 operating mode VPLLEN 15 R/W NONE * VPLL enable VPLLSTBY 16 R/W RESETB 0 VPLL controlled by standby Spare 17 R/W RESETB 0 For future use VUSB2EN 18 R/W RESETB 0 VUSB2 enable VUSB2STBY 19 R/W RESETB 0 VUSB2 controlled by standby Spare 20 R/W RESETB 0 For future use MC13892 140 Analog Integrated Circuit Device Data Freescale Semiconductor SPI BITMAP Table 144. Register 32, Regulator Mode 0 Bit # R/W Unused Name 21 R Reset Default 0 Unused 22 R 0 Unused 23 R 0 Description Not available Table 145. Register 33, Regulator Mode 1 Name Bit # R/W Reset Default Description VGEN3EN 0 R/W RESETB 0 VGEN3 enable VGEN3STBY 1 R/W RESETB 0 VGEN3controlled by standby VGEN3MODE 2 R/W RESETB 0 VGEN3 operating mode VGEN3CONFIG 3 R/W RESETB 0 VGEN3 with external PNP Reserved 4 R 0 For future use Spare 5 R/W RESETB 0 For future use VCAMEN 6 R/W RESETB 0 VCAM enable VCAMSTBY 7 R/W RESETB 0 VCAM controlled by standby VCAMMODE 8 R/W RESETB 0 VCAM operating mode VCAMCONFIG 9 R/W RESETB 0 VCAM with external PNP Unused 10 R 0 Not available Reserved 11 R 0 For future use VVIDEOEN 12 R/W RESETB 0 VVIDEO enable VIDEOSTBY 13 R/W RESETB 0 VVIDEO controlled by standby VVIDEOMODE 14 R/W RESETB 0 VVIDEO operating mode VAUDIOEN 15 R/W RESETB 0 VAUDIO enable VAUDIOSTBY 16 R/W RESETB 0 VAUDIO controlled by standby Spare 17 R/W RESETB 0 For future use VSDEN 18 R/W RESETB 0 VSD enable VSDSTBY 19 R/W RESETB 0 VSD controlled by standby VSDMODE 20 R/W RESETB 0 VSD operating mode Unused 21 R 0 Unused 22 R 0 Unused 23 R 0 Not available Table 146. Register 34, Power Miscellaneous Name Bit # R/W Reset RESETB Default 0 Description REGSCPEN 0 R/W Unused 1 R 0 Regulator short circuit protection enable Unused 2 R 0 Unused 3 R 0 Unused 4 R 0 Unused 5 R GPO1EN 6 R/W RESETB 0 GPO1 enable GPO1STBY 7 R/W RESETB 0 GPO1 controlled by standby GPO2EN 8 R/W RESETB 0 GPO2 enable GPO2STBY 9 R/W RESETB 0 GPO2 controlled by standby GPO3EN 10 R/W RESETB 0 GPO3 enable GPO3STBY 11 R/W RESETB 0 GPO3 controlled by standby GPO4EN 12 R/W RESETB 0 GPO4 enable GPO4STBY 13 R/W RESETB 0 GPO4 controlled by standby Unused 14 R 0 Not available Not available 0 MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 141 SPI BITMAP Table 146. Register 34, Power Miscellaneous Name Bit # R/W Reset Default Description PWGT1SPIEN 15 R/W RESETB 1 Power Gate 1 enable PWGT2SPIEN 16 R/W RESETB 1 Power Gate 2 enable Spare 17 R/W RESETB 0 For future use Unused 18 R 0 Unused 19 R 0 Unused 20 R 0 GPO4ADIN 21 R/W Unused 22 R 0 Unused 23 R 0 RESETB 1 Not available GPO4 configured as ADC input (GPO drive tri-stated) Not available Table 147. Register 35, Unused Name Unused Bit # R/W 23-0 Reset R Default 0 Description Not available Table 148. Register 36, Unused Name Unused Bit # R/W 23-0 Reset R Default 0 Description Not available Table 149. Register 37, Unused Name Unused Bit # R/W 23-0 Reset R Default 0 Description Not available Table 150. Register 38, Unused Name Unused Bit # R/W 23-0 Reset R Default 0 Description Not available Table 151. Register 39, Unused Name Unused Bit # R/W 23-0 Reset R Default 0 Description Not available Table 152. Register 40, Unused Name Unused Bit # R/W 23-0 Reset R Default 0 Description Not available Table 153. Register 41, Unused Name Unused Bit # R/W 23-0 Reset R Default 0 Description Not available Table 154. Register 42, Unused Name Unused Bit # 23-0 R/W R Reset Default 0 Description Not available MC13892 142 Analog Integrated Circuit Device Data Freescale Semiconductor SPI BITMAP Table 155. Register 43, ADC 0 Name Bit # R/W Reset Default Description LICELLCON 0 R/W RESETB 0 Enables lithium cell reading CHRGICON 1 R/W RESETB 0 Enables charge current reading BATICON 2 R/W RESETB 0 Enables battery current reading BUFFEN 3 R/W RESETB 0 Input buffer enable ADIN7SEL0 4 R/W RESETB 0 GP ADC Channel 7 mux selection 0 ADIN7SEL1 5 R/W RESETB 0 GP ADC Channel 7 mux selection 1 Unused 6 R 0 Unused 7 R 0 ADRESET 8 RWM RESETB 0 Reset GP ADC system ADIN7DIV 9 R/W RESETB 0 Divide by 2 enable for ADIN7 TSREFEN 10 R/W RESETB 0 Enables the touch screen reference Reserved 11 R 0 For future use TSMOD0 12 R/W RESETB 0 TSMOD1 13 R/W RESETB 0 TSMOD2 14 R/W RESETB 0 CHRGRAWDIV 15 R/W RESETB 1 Sets CHRGRAW scaling to divide by 5 ADINC1 16 R/W RESETB 0 Auto increment for ADA1 ADINC2 17 R/W RESETB 0 Auto increment for ADA2 Unused 18 R 0 Not available Spare 19 R/W 0 For future use Unused 20 R 0 Unused 21 R 0 Unused 22 R 0 ADCBIS0 23 W 0 RESETB Not available Sets the touch screen interface mode Not available Access to the ADCBIS control Table 156. Register 44, ADC 1 Name Bit # ADEN 0 RAND ADCCAL R/W Reset Default Description R/W RESETB 0 Enables the ADC 1 R/W RESETB 0 Sets the single channel mode 2 RWM RESETB 0 ADC Calibration ADSEL 3 R/W RESETB 0 Selects the set of inputs TRIGMASK 4 R/W RESETB 0 Trigger event masking ADA10 5 R/W RESETB 0 ADA11 6 R/W RESETB 0 ADA12 7 R/W RESETB 0 ADA20 8 R/W RESETB 0 ADA21 9 R/W RESETB 0 ADA22 10 R/W RESETB 0 ATO0 11 R/W RESETB 0 ATO1 12 R/W RESETB 0 ATO2 13 R/W RESETB 0 ATO3 14 R/W RESETB 0 ATO4 15 R/W RESETB 0 ATO5 16 R/W RESETB 0 ATO6 17 R/W RESETB 0 ATO7 18 R/W RESETB 0 ATOX 19 R/W RESETB 0 Sets ATO delay for any conversion ASC 20 RWM RESETB 0 Starts conversion ADTRIGIGN 21 R/W RESETB 0 Ignores the ADTRIG input Channel selection 1 Channel selection 2 Delay before first conversion MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 143 SPI BITMAP Table 156. Register 44, ADC 1 Name Bit # R/W Reset Default Description ADONESHOT 22 R/W RESETB 0 Single trigger event only ADCBIS1 23 W RESETB 0 Access to the ADCBIS control Table 157. Register 45, ADC 2 Name Bit # R/W Reset Default Spare 0 R NONE 0 Spare 1 R NONE 0 ADD10 2 R NONE 0 ADD11 3 R NONE 0 ADD12 4 R NONE 0 ADD13 5 R NONE 0 ADD14 6 R NONE 0 ADD15 7 R NONE 0 ADD16 8 R NONE 0 ADD17 9 R NONE 0 ADD18 10 R NONE 0 ADD19 11 R NONE 0 Spare 12 R NONE 0 Spare 13 R NONE 0 ADD20 14 R NONE 0 ADD21 15 R NONE 0 ADD22 16 R NONE 0 ADD23 17 R NONE 0 ADD24 18 R NONE 0 ADD25 19 R NONE 0 ADD26 20 R NONE 0 ADD27 21 R NONE 0 ADD28 22 R NONE 0 ADD29 23 R NONE 0 Description For 12-bit use Results for channel selection 1 For 12-bit use Results for channel selection 2 Table 158. Register 46, ADC 3 Name Bit # R/W Reset Default Unused 0 R 0 Unused 1 R 0 Unused 2 R 0 Unused 3 R 0 Unused 4 R 0 Unused 5 R ICID0 6 R NONE 1 ICID1 7 R NONE 1 ICID2 8 R NONE 1 Description Not available 0 Generation ID MC13892 144 Analog Integrated Circuit Device Data Freescale Semiconductor SPI BITMAP Table 158. Register 46, ADC 3 Name Bit # R/W Reset Default Unused 9 R 0 Unused 10 R 0 Unused 11 R 0 Unused 12 R 0 Unused 13 R 0 Unused 14 R 0 Unused 15 R 0 Unused 16 R 0 Unused 17 R 0 Unused 18 R 0 Unused 19 R 0 Unused 20 R 0 Unused 21 R 0 Unused 22 R 0 Reserved 23 R 0 Description Not available For future use Table 159. Register 47, ADC 4 Name Bit # R/W Reset Default Spare 0 R NONE 0 Spare 1 R NONE 0 ADDBIS10 2 R NONE 0 ADDBIS11 3 R NONE 0 ADDBIS12 4 R NONE 0 ADDBIS13 5 R NONE 0 ADDBIS14 6 R NONE 0 ADDBIS15 7 R NONE 0 ADDBIS16 8 R NONE 0 ADDBIS17 9 R NONE 0 ADDBIS18 10 R NONE 0 ADDBIS19 11 R NONE 0 Spare 12 R NONE 0 Spare 13 R NONE 0 ADDBIS20 14 R NONE 0 ADDBIS21 15 R NONE 0 ADDBIS22 16 R NONE 0 ADDBIS23 17 R NONE 0 ADDBIS24 18 R NONE 0 ADDBIS25 19 R NONE 0 ADDBIS26 20 R NONE 0 ADDBIS27 21 R NONE 0 ADDBIS28 22 R NONE 0 ADDBIS29 23 R NONE 0 Description For 12-bit use Result for channel selection 1 of ADCBIS For 12-bit use Result for channel selection 2 of ADCBIS MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 145 SPI BITMAP Table 160. Register 48, Charger 0 Name Bit # R/W Reset Default Description VCHRG0 0 R/W RESETB 1 VCHRG1 1 R/W RESETB 1 VCHRG2 2 R/W RESETB 0 ICHRG0 3 RWM RESETB 0 ICHRG1 4 RWM RESETB 0 ICHRG2 5 RWM RESETB 0 ICHRG3 6 RWM RESETB 0 TREN 7 R/W RESETB 0 Enables the internal trickle charger current ACKLPB 8 R/W RESETB 0 Acknowledge Low-power Boot THCHKB 9 R/W RESETB 0 Battery thermistor check disable FETOVRD 10 R/W RESETB 0 Allows BATTFET Control FETCTRL 11 R/W RESETB 0 BATTFET Control Spare 12 R/W RESETB 0 For future use RVRSMODE 13 RWM RESETB 0 Reverse mode enable Unused 14 R 0 Not available PLIM0 15 R/W RESETB 0 PLIM1 16 R/W RESETB 0 PLIMDIS 17 R/W RESETB 0 Power limiter disable CHRGLEDEN 18 R/W RESETB 0 CHRGLED enable CHGTMRRST 19 RWM RESETB 0 Charge timer reset CHGRESTART 20 RWM RESETB 0 Restarts charger state machine CHGAUTOB 21 R/W RESETB 0 Avoids automatic charging while on CYCLB 22 R/W RESETB 1 Disables cycling CHGAUTOVIB 23 R/W RESETB 0 Allows V and I programming Sets the charge regulator output voltage Sets the main charger DAC current Power limiter setting Table 161. Register 49, USB 0 Name Bit # R/W Reset Default Reserved 0 R 0 Reserved 1 R 0 Reserved 2 R 0 Reserved 3 R 0 Reserved 4 R 0 Reserved 5 R Spare 6 R/W Reserved 7 R 0 Reserved 8 R 0 Reserved 9 R 0 Reserved 10 R 0 Reserved 11 R 0 Reserved 12 R 0 Reserved 13 R 0 Reserved 14 R 0 Reserved 15 R 0 Reserved 16 R 0 Unused 17 R 0 Unused 18 R 0 Reserved 19 R 0 Reserved 20 R 0 Reserved 21 R 0 Description For future use 0 RESETB 1 For future use Not available For future use MC13892 146 Analog Integrated Circuit Device Data Freescale Semiconductor SPI BITMAP Table 161. Register 49, USB 0 Name Bit # R/W IDPUCNTRL 22 R/W Reserved 23 R Reset Default RESETB Description 0 UID pin pull up source select 0 For future use Table 162. Register 50, Charger USB 1 Name Bit # R/W Reset NONE Default VUSBIN 0 R/W * Unused 1 R 0 Unused 2 R 0 VUSBEN 3 R/W Unused 4 R 0 Unused 5 R 0 Reserved 6 R 0 Reserved 7 R 0 ID100KPU 8 R/W Reserved 9 R OTGSWBSTEN 10 R/W Reserved 11 R 0 Reserved 12 R 0 Reserved 13 R 0 Unused 14 R 0 Unused 15 R 0 Reserved 16 R Spare 17 R/W RESETB 0 Spare 18 R/W RESETB 0 Unused 19 R 0 Unused 20 R 0 Unused 21 R 0 Unused 22 R 0 Unused 23 R 0 Description Slave or Host configuration for VBUS Not available RESETB 1 VUSB enable (PUMS2=Open) Also reset to 1 by invalid VBUS NONE * VUSB enable (PUMS2=GND) RESETB RESETB Not available For future use 0 Switches in 100K UID pull-up 0 For future use 0 Enable SWBST for USB OTG mode For future use Not available 0 For future use For future use Not available Table 163. Register 51, LED Control 0 Name Bit # R/W Reset Default Description Spare 0 R/W RESETB 0 For future use LEDMDHI 1 R/W RESETB 0 Main display driver high current mode LEDMDRAMP 2 R/W RESETB 0 Main display driver ramp enable LEDMDDC0 3 R/W RESETB 0 LEDMDDC1 4 R/W RESETB 0 LEDMDDC2 5 R/W RESETB 0 LEDMDDC3 6 R/W RESETB 0 LEDMDDC4 7 R/W RESETB 0 LEDMDDC5 8 R/W RESETB 0 LEDMD0 9 R/W RESETB 0 LEDMD1 10 R/W RESETB 0 LEDMD2 11 R/W RESETB 0 Spare 12 R/W RESETB 0 For future use LEDADHI 13 R/W RESETB 0 Auxiliary display driver high current mode LEDADRAMP 14 R/W RESETB 0 Auxiliary display driver ramp enable Main display driver duty cycle Main display driver current setting MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 147 SPI BITMAP Table 163. Register 51, LED Control 0 Name Bit # R/W Reset Default LEDADDC0 15 R/W RESETB 0 LEDADDC1 16 R/W RESETB 0 LEDADDC2 17 R/W RESETB 0 LEDADDC3 18 R/W RESETB 0 LEDADDC4 19 R/W RESETB 0 LEDADDC5 20 R/W RESETB 0 LEDAD0 21 R/W RESETB 0 LEDAD1 22 R/W RESETB 0 LEDAD2 23 R/W RESETB 0 Description Auxiliary display driver duty cycle Auxiliary display driver current setting Table 164. Register 52, LED Control 1 Name Bit # R/W Reset Default Description Spare 0 R/W RESETB 0 For future use LEDKPHI 1 R/W RESETB 0 Keypad driver high current mode LEDKPRAMP 2 R/W RESETB 0 Keypad driver ramp enable LEDKPDC0 3 R/W RESETB 0 LEDKPDC1 4 R/W RESETB 0 LEDKPDC2 5 R/W RESETB 0 LEDKPDC3 6 R/W RESETB 0 LEDKPDC4 7 R/W RESETB 0 LEDKPDC5 8 R/W RESETB 0 LEDKP0 9 R/W RESETB 0 LEDKP1 10 R/W RESETB 0 LEDKP2 11 R/W RESETB 0 Spare 12 R/W RESETB 0 Spare 13 R/W RESETB 0 Spare 14 R/W RESETB 0 Unused 15 R 0 Unused 16 R 0 Unused 17 R 0 Unused 18 R 0 Unused 19 R 0 Unused 20 R 0 Unused 21 R 0 Unused 22 R 0 Unused 23 R 0 Keypad driver duty cycle Keypad driver current setting For future use Not available Not available Table 165. Register 53, LED Control 2 Name Bit # R/W Reset Default LEDRPER0 0 R/W RESETB 0 LEDRPER1 1 R/W RESETB 0 LEDRRAMP 2 R/W RESETB 0 LEDRDC0 3 R/W RESETB 0 LEDRDC1 4 R/W RESETB 0 LEDRDC2 5 R/W RESETB 0 LEDRDC3 6 R/W RESETB 0 LEDRDC4 7 R/W RESETB 0 LEDRDC5 8 R/W RESETB 0 Description Red channel blink period Red channel driver ramp enable Red channel driver duty cycle MC13892 148 Analog Integrated Circuit Device Data Freescale Semiconductor SPI BITMAP Table 165. Register 53, LED Control 2 Name Bit # R/W Reset Default LEDR0 9 R/W RESETB 0 LEDR1 10 R/W RESETB 0 LEDR2 11 R/W RESETB 0 LEDGPER0 12 R/W RESETB 0 LEDGPER1 13 R/W RESETB 0 LEDGRAMP 14 R/W RESETB 0 LEDGDC0 15 R/W RESETB 0 LEDGDC1 16 R/W RESETB 0 LEDGDC2 17 R/W RESETB 0 LEDGDC3 18 R/W RESETB 0 LEDGDC4 19 R/W RESETB 0 LEDGDC5 20 R/W RESETB 0 LEDG0 21 R/W RESETB 0 LEDG1 22 R/W RESETB 0 LEDG2 23 R/W RESETB 0 Description Red channel driver current setting Green channel blink period Green channel driver ramp enable Green channel driver duty cycle Green channel driver current setting Table 166. Register 54, LED Control 3 Name Bit # R/W Reset Default LEDBPER0 0 R/W RESETB 0 LEDBPER1 1 R/W RESETB 0 LEDBRAMP 2 R/W RESETB 0 LEDBDC0 3 R/W RESETB 0 LEDBDC1 4 R/W RESETB 0 LEDBDC2 5 R/W RESETB 0 LEDBDC3 6 R/W RESETB 0 LEDBDC4 7 R/W RESETB 0 LEDBDC5 8 R/W RESETB 0 LEDB0 9 R/W RESETB 0 LEDB1 10 R/W RESETB 0 LEDB2 11 R/W RESETB 0 LEDSWBSTEN 12 R/W RESETB 0 Spare 13 R/W RESETB 0 Spare 14 R/W RESETB 0 Unused 15 R 0 Unused 16 R 0 Unused 17 R 0 Unused 18 R 0 Unused 19 R 0 Unused 20 R 0 Unused 21 R 0 Unused 22 R 0 Unused 23 R 0 Description Blue channel blink period Blue channel driver ramp enable Blue channel driver duty cycle Blue channel driver current setting Enable SWBST for RGB LED's For future use Not available Table 167. Register 55, Not Used Name Unused Bit # 23-0 R/W R Reset Default 0 Description Not available MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 149 SPI BITMAP Table 168. Register 56, Not Used Name Unused Bit # 23-0 R/W Reset R Default 0 Description Not available Table 169. Register 57, FSL Use Only Name FSL Use Only Bit # 23-0 R/W R/W Reset RTCPORB Default Description FSL Table 170. Register 58, FSL Use Only Name FSL Use Only Bit # 23-0 R/W Reset R/W RTCPORB Default Description FSL Table 171. Register 59, FSL Use Only Name FSL Use Only Bit # 23-0 R/W Reset R/W RTCPORB Default Description FSL Table 172. Register 60, FSL Use Only Name FSL Use Only Bit # 23-0 R/W Reset R/W RTCPORB Default Description FSL Table 173. Register 61, FSL Use Only Name FSL Use Only Bit # 23:0 R/W Reset R/W RTCPORB Default Description FSL Table 174. Register 62, FSL Use Only Name FSL Use Only Bit # 23:0 R/W R/W Reset RTCPORB Default Description FSL Table 175. Register 63, FSL Use Only Name FSL Use Only Bit # 23:0 R/W R/W Reset RTCPORB Default Description FSL MC13892 150 Analog Integrated Circuit Device Data Freescale Semiconductor TYPICAL APPLICATIONS TYPICAL APPLICATIONS Figure 35 contains a typical application of the MC13892. For convenience, components for use with the MC13892 are cited within this document. Freescale does not assume liability, endorse, or warrant components from external manufacturers that are referenced in circuit drawings or tables. While Freescale offers component recommendations in this configuration, it is the customer's responsibility to validate their application. From Extenal Boost Charger/USB Input (Tied to VBUS) Tied to BATTISNSCC R1 20m Main Battery BP M3 R2 100m M2 M1 2.2u SWBST 10u GNDLED LEDR LEDG LEDB GNDBL LEDKP SW3 Tri-Color LED Drive Backlight LED Drive PWR Gate Drive & Chg Pump ADIN5 General Purpose ADC Inputs: i.e., Battery pack thermistor, PA thermistor, Light Sensor, Etc. SW1 1050 mA Buck ADIN6 TSX1 10 Bit GP ADC MUX SW2 800 mA Buck A/D Result TSX2 Touch Screen Interface TSY1 TSY2 A/D Control Touch Screen Interface Trigger Handling TSREF From AP From M3/R1 connection (needs to be separate route from BATTISNS) Die Temp & Thermal Warning Detection ADTRIG SW3 800 mA Buck To Interrupt Section SW4 800 mA Buck BATTISNSCC BATT CFP Coulomb CCOUT Counter CFM SPIVCC SPI Interface + Muxed I2C Optional Interface MISO GNDSPI SPI 100n Registers SWBST O/P Drive SW4IN SW4OUT GNDSW4 SW4FB DVS2 UID O/P Drive SWBST 300 mA Boost Input Pin Bi-directional Pin MC13892 VBUS/ID Detectors SWBSTIN SWBSTOUT SWBSTFB GNDSWBST OTG 5V SPI VUSB Regulator PLL VUSB2 Pass FET BP 4.7u SW3 Output 2.2u VAUDIO Pass FET VVIOHI Pass FET VPLL Pass FET VDIG Pass FET SW4 Output 2.2u BP From AP HOLD Switch To GND, Open, VCOREDIG or VCORE 32.768 KHz Crystal On/Off Button 4.7u SWBST Output (Boost) BP 10u 2.2u Pass FET 2.2u VIINAUDIO VAUDIO BP VINIOHI VIOHI BP 2.2u VINPLL VPLL BP 2.2u VINDIG VDIG BP 2.2u VCAM 2.2u BP 2.2u BP VSDDRV VSD VGEN1DRV VGEN1 VGEN2 VGEN2DRV VGEN2 2.2u BP LICELL VSRTC RESETB CLK32K To/From Peripherals 2.2u BP 2.2u To/From AP Pass FET BP VGEN3 2.2u Best of Supply GNDREG1 GPO Control VSRTC STANDBYSEC INT WDI To/From AP RESETBMCU STANDBY From Docking station PUMS1 PUMS2 MODE XTAL2 18p 10u From AP BP VGEN1 VGEN3 32 KHz Buffers Core Control Logic, Timers, & Interrupts GNDCTRL GNDRTC XTAL1 GNDSUB8 GNDSUB9 GNDSUB7 GNDSUB4 GNDSUB5 GNDSUB6 Enables & Control 10u GNDREG2 GNDREG3 1.0u To External Camera Flash or Aux Light Sensor To External Audio Enable To Light Sensor Enable To Thermistor Bias 18p Interrupt Inputs 10u VINGEN3DRV CLK32KMCU SPI Result Registers 32 KHz Crystal Osc GNDSUB3 4.7u VINUSB2 VUSB2 Switchers RTC + Calibration 32 KHz Internal Osc Switch PWRON1 PWRON2 PWRON3 LCELL Li Cell Charger GNDSUB1 GNDSUB2 Control Logic Monitor Timer BP BP 2.2u GPO1 GPO2 GPO3 GPO4 Startup Sequencer Decode Trim? PUMS LICELL 4.7u BP VUSB 100n SW2 Output BP BP To Trimmed Circuits Trim-In-Package Control Logic To 1.8V Peripherals 2 x22u VVIDEODRV VVIDEO VINCAMDRV 2.2u Coin Cell Battery 1.5u SPI Control VSD VINUSB 4.7u Shift Register Reference Generation UVBUS VBUSEN O/P Drive SW3IN SW3OUT GNDSW3 SW3FB DVS1 VCAM From AP SW2IN SW2OUT GNDSW2 SW2FB VVIDEO Connector Interface ID CHRGRAW REFCORE GNDCORE O/P Drive SW1 Output 2.2u To Enables & Control VCORE VCOREDIG 2.2u To/From USB Cable MC13892 IC Shift Register CS CLK MOSI 2.2u SW1IN SW1OUT GNDSW1 SW1FB Package Pin Legend Output Pin AP CSPI O/P Drive DVS CONTROL To SPI 10uF SW4 To Memory User Off, Memory Hold PWGTDRV2 BP Voltage / Current Sensing & Translation ADIN7 SW4 PWGTDRV1 LICELL, UID, Die Temp, GPO4 GNDADC Processor Internal Memory User Off To 1.2V Peripherals Charger Interface and Control: 4 bit DAC, Clamp, Protection, Trickle Generation Battery Interface & Protection LEDAD LEDMD GNDCHRG CHRGSE1B CHRGLED CHRGRAW CHRGCTRL1 CHRGISNS CHRGCTRL2 BP BPSNS BATTFET BATT BATTISNS BP 10u Possible applications, may also be used for enables to adjunct supplies or modules as necessary Figure 35. MC13892 Typical Application MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 151 PACKAGING PACKAGE DIMENSIONS PACKAGING PACKAGE DIMENSIONS For the most current package revision, visit www.freescale.com and perform a keyword search using the "98A" listed below. VK SUFFIX 139-PIN 98ASA10820D REVISION 0 MC13892 152 Analog Integrated Circuit Device Data Freescale Semiconductor PACKAGING PACKAGE DIMENSIONS VK SUFFIX 139-PIN 98ASA10820D REVISION 0 MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 153 PACKAGING PACKAGE DIMENSIONS VL SUFFIX 186-PIN 98ASA10849D REVISION 0 MC13892 154 Analog Integrated Circuit Device Data Freescale Semiconductor PACKAGING PACKAGE DIMENSIONS VL SUFFIX 186-PIN 98ASA10849D REVISION 0 MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 155 ADDITIONAL DOCUMENTATION ADDITIONAL DOCUMENTATION Table 176. Additional Documentation Document Number Description MC13892ER MC13892ER, Silicon Mask Errata MC13783 MC13783, Power Management and Audio Circuit MC13892 156 Analog Integrated Circuit Device Data Freescale Semiconductor REVISION HISTORY REVISION HISTORY REVISION DATE 14.0 11/2011 DESCRIPTION * * * * Added MC13892CJVK and MC13892CJVL to the ordering information Changed RT from 45 k to 4.5 k in Table 73 for THIGH In the Static Electrical Characteristics table, changed Input Operating Voltage - CHRGRAW from 17 V to 5.6 V on page 24. Changed Input Operating Voltage - CHRGRAW from 17 V to 5.6 V in Table 64. 15.0 4/2012 * Added MC13892DJVK and MC13892DJVL to Table 1, MC13892 Device Variations. 16.0 4/2012 * Corrected Global Reset Functions in Table 1 17.0 5/2012 * Clarified the Global Reset function for silicon versions A, B, C and D throughout the document * Section PWRON1, 2 and 3 on page 37 * Section Global System Restart on page 60 * Table 125, Register 13, Power Control 0 18.0 10/2012 * * * Reformatted Table 111 so it can be seen in its entirety, rotated 90 degrees Rotated tables 112-114 to portrait format. Readjusted the footer position to match template. 4/2013 * No technical changes. Revised back page. Updated document properties. Added SMARTMOS sentence to first paragraph. 4/2014 * Added Additional note to Battery Thermistor Check Operation 19.0 MC13892 Analog Integrated Circuit Device Data Freescale Semiconductor 157 How to Reach Us: Information in this document is provided solely to enable system and software implementers to use Freescale products. Home Page: freescale.com There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits based Web Support: freescale.com/support Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no on the information in this document. warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Freescale data sheets and/or specifications can and do vary in different applications, and actual performance may vary over time. All operating parameters, including "typicals," must be validated for each customer application by customer's technical experts. Freescale does not convey any license under its patent rights nor the rights of others. Freescale sells products pursuant to standard terms and conditions of sale, which can be found at the following address: freescale.com/SalesTermsandConditions. Freescale and the Freescale logo are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. SMARTMOS is a trademark of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. (c) 2014 Freescale Semiconductor, Inc. Document Number: MC13892 Rev. 19.0 4/2014 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Freescale Semiconductor: KIT13892VLEVBEJ KIT13892VKEVBEJ MC13892CJVL MC13892CJVLR2 MC13892DJVK MC13892DJVKR2 MC13892DJVL MC13892DJVLR2 MC13892CJVKR2 MC13892CJVK