REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Make change to the power dissipation and derating limits for case outline G. Delete +125C and substitute +150C in footnote 4/ under 1.4. Add footnote 2/ to the input voltage range test under Table I. Delete footnote 2/ from the input noise voltage and current density tests under Table I. Delete the input noise voltage test entirely. Delete footnote 2/ from the slew rate test under Table I. Add footnote 4/ to the gain bandwidth product test under Table I. Average temperature coefficient on input offset voltage test, renumber footnote 2/ as footnote 4/ under Table I. Change the note under Table II. Changes in accordance with N.O.R. 5962-R050-95. Add case outline X. Remove vendor CAGE for case outline G. Editorial and technical changes throughout. Redrawn. 95-01-24 M. A. FRYE 96-01-30 M. A. FRYE B C Drawing updated to reflect current requirements. - ro 08-04-03 R. HEBER D Update document paragraphs to current MIL-PRF-38535 requirements. - ro 15-05-19 C. SAFFLE THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY GARY ZAHN STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http://www.landandmaritime.dla.mil CHECKED BY RAY MONNIN APPROVED BY THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A MICHAEL A. FRYE DRAWING APPROVAL DATE 88-07-27 REVISION LEVEL D MICROCIRCUIT, LINEAR, LOW NOISE, HIGH SPEED PRECISION, OPERATIONAL AMPLIFIER, MONOLITHIC SILICON SIZE CAGE CODE A 67268 SHEET DSCC FORM 2233 APR 97 5962-88622 1 OF 12 5962-E320-15 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-88622 01 G A Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function VOS 01 02 LT1028M LT1028AM Operational amplifier Operational amplifier 80 V 40 V 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator G P X MACY1-X8 GDIP1-T8 or CDIP2-T8 See figure 1 Terminals Package style 8 8 8 Can Dual-in-line Can 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. 1/ Supply voltage: TA = -55C to +105C ............................................................................................... 22 V TA = +105C to +125C ............................................................................................. Input voltage ................................................................................................................. Differential input current ................................................................................................ Output short circuit duration .......................................................................................... Storage temperature range ........................................................................................... 16 V Equal to supply voltage 25 mA 2/ Indefinite -65C to +150C Power dissipation (PD) : 3/ Cases G and X .......................................................................................................... Case P ...................................................................................................................... Lead temperature (soldering, 10 seconds) ................................................................... Junction temperature (TJ) ............................................................................................. 500 mW at +75C 750 mW at +75C +300C +150C Thermal resistance, junction-to-case (JC) ................................................................... See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA) : Cases G and X .......................................................................................................... 150C/W Case P ...................................................................................................................... 100C/W ______ 1/ Internal thermal limiting prevents excessive heating that could result in sudden failure. The device can be subjected to accelerated stress with a shorted output and worst case conditions. 2/ The inputs are protected by back-to-back diodes. Current limiting resistors are not used in order to achieve low noise. If differential input voltage exceeds 1.8 V, the input current should be limited to 25 mA. 3/ Derate: Case G, 6.7 mW/C above 75C; case P, 10 mW/C above 75C. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88622 A REVISION LEVEL D SHEET 2 1.4 Recommended operating conditions. Supply voltage (VS) .................................................................................................... 4.5 V to 15 V Ambient operating temperature range (TA) .................................................................. -55C to +125C 4/ 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 MIL-STD-1835 - Test Method Standard Microcircuits. Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 MIL-HDBK-780 - List of Standard Microcircuit Drawings. Standard Microcircuit Drawings. (Copies of these documents are available online at http://quicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094). 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for nonJAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. _____ 4/ The maximum operating junction temperature is +150C. At elevated temperatures, the device must be derated based on package thermal resistance. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88622 A REVISION LEVEL D SHEET 3 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device. 3.5.1 Certification/compliance mark. A compliance indicator "C" shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator "C" shall be replaced with a "Q" or "QML" certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for any change that affects this drawing. 3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritime's agent, and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88622 A REVISION LEVEL D SHEET 4 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Min Input offset voltage 1 VIO 1/ 2,3 Input voltage range 1 VIN 2/ Input bias current IIB 1 2,3 Input offset current IIO 1 VCM = 0.0 V 2,3 Output voltage swing VOUT 4 RL 600 RL 2.0 k 5.6 Input noise voltage density en 7 fO = 10 Hz, TA = +25C fO = 1.0 kHz, TA = +25C Input noise current density in fO = 10 Hz, 7 3/ TA = +25C fO = 1.0 kHz, 3/ TA = +25C Max 01 80 02 40 01 180 02 120 11 All V V 10.3 2,3 VCM = 0.0 V Unit 01 180 02 90 01 300 02 150 01 100 02 50 01 180 02 90 01 10.5 02 11.0 01 12.0 02 12.3 01 10.3 02 10.3 nA nA V 01 2.4 nV / 02 2.2 Hz 01 1.2 02 1.1 01 16 pA / 02 14 Hz 01 1.8 02 1.6 See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88622 A REVISION LEVEL D SHEET 5 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Min Slew rate SR 4 AVCL = -1 All GBWP fO = 20 kHz, 4/ Max 11.0 5.6 Gain bandwidth product Unit V/s 7.5 7 All 50 MHz 4 01 2.0 02 1.3 01 10.5 pA / 02 9.5 Hz 01 13.0 02 11.5 TA = +25C Average temperature coefficient of input offset voltage VIO / Supply current IS 4/ T 1 IL = 0.0 mA 2,3 Large signal voltage gain AVOL 4 VOUT = 12 V, RL 2.0 k 5,6 VOUT = 10 V, RL 2.0 k 4 VOUT = 10 V, RL 1.0 k 5,6 4 VOUT = 10 V, RL 600 01 5.0 02 7.0 01 2.0 02 3.0 01 3.5 02 5.0 01 1.5 02 2.0 01 2.0 02 3.0 V/C V/V See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88622 A REVISION LEVEL D SHEET 6 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Min Common mode rejection ratio CMRR 1 VCM = 11.0 V 2,3 VCM = 10.3 V Power supply rejection ratio PSRR 1 4.0 V VS 18 V 2,3 4.5 V VS 16 V 1/ 2/ 3/ 4/ 01 110 02 114 01 100 02 106 01 110 02 117 01 104 02 110 Unit Max dB dB Input offset voltage measurement are performed by automatic test equipment approximately 0.5 seconds after application of power. This test is guaranteed by the CMRR test. Current noise is defined and measured with balanced source resistors. The resultant voltage noise (after subtracting the resistor noise on an rms basis) is divided by the sum of the two source resistors to obtain current noise. If not tested, shall be guaranteed to the limits specified in table I. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA = +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88622 A REVISION LEVEL D SHEET 7 Case outline X FIGURE 1. Case outline. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88622 A REVISION LEVEL D SHEET 8 Case outline X - continued Symbol Dimensions Notes Inches Millimeters Min Max Min Max A .165 .185 4.19 4.70 b1 .016 .021 .41 .53 b2 .016 .024 .41 .61 D .335 .370 8.51 9.40 D1 .305 .335 7.75 8.51 D2 .110 .160 2.79 4.06 e .230 BSC 2 5.84 BSC F --- .040 --- 1.02 K .028 .034 .71 .86 K1 .027 .045 .69 1.14 3 L .500 .750 12.70 19.05 2 L1 --- .050 --- 1.27 2 Q .010 .045 .25 1.14 Note 45 4 45 1, 5, 6 NOTES: 1/ The U.S. government preferred system of measurement is the metric SI system. However, since this item was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. 2/ Diameter is uncontrolled in L1 and beyond form the reference plane. 3/ Measured from maximum diameter of the product. 4/ is the basic spacing from the centerline of the tab to terminal 1, looking at the bottom of the package. 5/ Leads having a maximum diameter .019 inch (0.48 mm) measured in gauging plane .054 inch (1.37 mm) + .001 inch (0.02 mm) - .000 inch (0.00 mm) inches below the base plane of the product shall be within .007 inch (0.17 mm) of their true position relative to a maximum width tab. 6/ This style package may be measured by direct methods or by gauge. FIGURE 1. Case outline - continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88622 A REVISION LEVEL D SHEET 9 Device types 01 and 02 Case outlines G, P, and X Terminal number Terminal symbol 1 VOS TRIM 2 -INPUT 3 +INPUT 4 -VS 5 OVER - COMP 6 OUTPUT 7 +VS 8 VOS TRIM FIGURE 2. Terminal connections. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88622 A REVISION LEVEL D SHEET 10 TABLE II. Electrical test requirements. MIL-STD-883 test requirements Interim electrical parameters (method 5004) Final electrical test parameters (method 5004) Group A test requirements (method 5005) Groups C and D end-point electrical parameters (method 5005) Subgroups (in accordance with MIL-STD-883, method 5005, table I) --1*, 2, 3, 4, 5, 6 1, 2, 3, 4, 5, 6, 7 1 * PDA applies to subgroup 1 except for the input offset voltage test. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 8, 9, 10, and 11 in table I, method 5005 of MIL-STD-883 shall be omitted. 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA = +125C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88622 A REVISION LEVEL D SHEET 11 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962) should contact DLA Land and Maritime-VA, telephone (614) 692-8108. 6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990, or telephone (614) 692-0540. 6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103 and QML-38535. The vendors listed in MIL-HDBK-103 and QML-38535 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DLA Land and Maritime-VA. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88622 A REVISION LEVEL D SHEET 12 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 15-05-19 Approved sources of supply for SMD 5962-88622 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DLA Land and Maritime-VA. This information bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DLA Land and Maritime maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/. Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-8862201GA 3/ LT1028MH/883 5962-8862201PA 60264 MTLT1028QD8 3/ LT1028MJ8/883 60264 MTLT1028QH 3/ LT1028MH/883 5962-8862202GA 3/ LT1028AMH/883 5962-8862202PA 60264 MTLT1028AQD8 3/ LT1028AMJ8/883 60264 MTLT1028AQH 3/ LT1028AMH/883 5962-8862201XA 5962-8862202XA 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 3/ Not available from an approved source of supply. Vendor CAGE number 60264 Vendor name and address Minco Technology Labs, Inc. 1805 Rutherford Lane Austin, TX 78754-5101 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin.