REVISIONS
LTR DESCRIPTION DATE (YR-MO-DA) APPROVED
A Make change to the power dissipation and derating limits for case outline G.
Delete +125C and substitute +150C in footnote 4/ under 1.4.
Add footnote 2/ to the input voltage range test under Table I.
Delete footnote 2/ from the input noise voltage and current density tests under
Table I. Delete the input noise voltage test entirely.
Delete footnote 2/ from the slew rate test under Table I.
Add footnote 4/ to the gain bandwidth product test under Table I.
Average temperature coefficient on input offset voltage test, renumber
footnote 2/ as footnote 4/ under Table I. Change the note under Table II.
Changes in accordance with N.O.R. 5962-R050-95.
95-01-24 M. A. FRYE
B Add case outline X. Remove vendor CAGE for case outline G.
Editorial and technical changes throughout. Redrawn. 96-01-30 M. A. FRYE
C Drawing updated to reflect current requirements. - ro 08-04-03 R. HEBER
D Update document paragraphs to current MIL-PRF-38535 requirements. - ro 15-05-19 C. SAFFLE
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS REV D D D D D D D D D D D D
OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12
PMIC N/A PREPARED BY
GARY ZAHN
DLA LAND AND MARITIME
COLUMBUS, OHIO 4321 8-3990
http://www.landandmaritime.dla.mil
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
CHECKED BY
RAY MONNIN
APPROVED BY
MICHAEL A. FRYE
MICROCIRCUIT, LINEAR, LOW NOISE, HIGH
SPEED PRECISION, OPERATIONAL AMPLIFIER,
MONOLITHIC SILICON
DRAWING APPROVAL DATE
88-07-27
AMSC N/A
REVISION LEVEL
D SIZE
A CAGE CODE
67268
5962-88622
SHEET 1 OF 12
DSCC FORM 2233
APR 97 5962-E320-15
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-88622
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
D SHEET 2
DSCC FORM 2234
APR 97
1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class lev el B microcircu its in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
5962-88622 01 G A
Drawing number Device type
(see 1.2.1) Case outline
(see 1.2.2) Lead finish
(see 1.2.3)
1.2.1 Device type(s). The device type(s) identify the circuit function as follows:
Device type Generic number Circuit function VOS
01 LT1028M Operational amplifier
80
V
02 LT1028AM Operatio nal a mplifier
40
V
1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter Descriptive designator Terminals Package style
G MACY1-X8 8 Can
P GDIP1-T8 or CDIP2-T8 8 Dual-in-line
X See figure 1 8 Can
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
1.3 Absolute maximum ratings. 1/
Supply voltage:
T
A = -55C to +105C ............................................................................................... 22 V
T
A = +105C to +125C ............................................................................................. 16 V
Input voltage ................................................................................................................. Equal to supply voltage
Differential input current ................................................................................................ 25 mA 2/
Output short circuit duration .......................................................................................... Indefinite
Storage temperature range ........................................................................................... -65C to +150C
Power dissipation (PD) : 3/
Cases G and X .......................................................................................................... 500 mW at +75C
Case P ...................................................................................................................... 750 mW at + 75C
Lead temperature (soldering, 10 seconds) ................................................................... +300C
Junction temperature (TJ) ............................................................................................. +150C
Thermal resistance, junction-to-case (JC) ................................................................... See MIL-STD-1835
Thermal resistance, junction-to-ambient (JA) :
Cases G and X .......................................................................................................... 150C/W
Case P ...................................................................................................................... 100C/W
______
1/ Internal thermal limiting prevents excessive heating that could result in sudden failure. The device can be sub jected to
accelerated stress with a shorted output and worst case conditio ns.
2/ The inputs are protected by back-to-back diodes. Current limiting resistors are not used in order to achieve low noise.
If differential input voltage exceeds 1.8 V, the input current should be limited to 25 mA.
3/ Derate: Case G, 6.7 mW/C above 75C; case P, 10 mW/C above 75C.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-88622
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
D SHEET 3
DSCC FORM 2234
APR 97
1.4 Recommended operating conditions.
Supply voltage (VS) .................................................................................................... 4.5 V to 15 V
Ambient operating temperature range (TA) .................................................................. -55C to +125C 4/
2. APPLICABLE DOCUMENT S
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-385 35 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard Electronic Comp onent Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents ar e available online at http://quicksearch.dla.mil or from the Standardization Document Order
Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094).
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-
JAN class level B devices and as specified h erein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified man ufacturer or a manufacturer who has been granted transitional certification to
MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and
qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management
(QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the
device. These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with
MIL-PRF-38535 is required to identify when the QML flow option is used.
3.2 Design, construction, and physica l dimensions. The design, construction, and ph ysical dimensions shall be as specified
in MIL-PRF-38535, appendix A and herein.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein and figure 1.
3.2.2 Terminal connections. The terminal conn ections shall be as specified on figure 2.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the el ectrical performance characteristics are
as specified in table I and shall app ly over the full ambient operating temperature range.
_____
4/ The maximum operating junction temperature is +150C. At elevated temperatures, the device must be derated based
on package thermal resistanc e.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-88622
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
D SHEET 4
DSCC FORM 2234
APR 97
3.4 Electrical test requirements. The electrical test requirements shall be the subgr oups specified in table II. The electrical
tests for each subgroup are described in tabl e I.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN
listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD
PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device.
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
3.6 Certificate of compliance. A certificate of compliance sh all be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 (see 6.6 her ein). The certificate of compliance submitted to DLA Land and
Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturer's product meets the
requirements of MIL-PRF-38535, appendix A and the requirements herein.
3.7 Certificate of conformance. A certificate of conformance as require d in MIL-PRF -38535, appendix A shall be provided
with each lot of microcircuits deliver ed to this drawing.
3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall b e requ ired for any change that
affects this drawing.
3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritime's agent, and the acq uiring activity retain the
option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made
available onshore at the optio n of the reviewer.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-88622
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
D SHEET 5
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristi cs.
Test Symbol Conditions
-55C TA +125C
unless otherwise specified
Group A
subgroups
Device
type
Limits Unit
Min Max
Input offset voltage VIO 1 01
80 V
1/ 02
40
2,3 01
180
02
120
Input voltage range VIN 1 All
11 V
2/ 2,3
10.3
Input bias current IIB V
CM = 0.0 V 1 01
180 nA
02
90
2,3 01
300
02
150
Input offset current IIO V
CM = 0.0 V 1 01
100 nA
02
50
2,3 01
180
02
90
Output voltage swing VOUT R
L 600 4 01
10.5 V
02
11.0
RL 2.0 k 01
12.0
02
12.3
5.6 01
10.3
02
10.3
Input noise voltage density en f
O = 10 Hz, TA = +25C 7 01 2.4 nV /
Hz
02 2.2
fO = 1.0 kHz, TA = +25C 01 1.2
02 1.1
Input noise current density in f
O = 10 Hz, 3/ 7 01 16 pA /
Hz
TA = +25C 02 14
fO = 1.0 kHz, 3/ 01 1.8
TA = +25C 02 1.6
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-88622
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
D SHEET 6
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics – Continued.
Test Symbol Conditions
-55C TA +125C
unless otherwise specified
Group A
subgroups
Device
type
Limits Unit
Min Max
Slew rate SR AVCL = -1 4 All 11.0
V/s
5.6 7.5
Gain bandwidth product GBWP fO = 20 kHz, 4/
TA = +25C
7 All 50 MHz
Average temperature
coefficient of input offset
voltage
VIO /
T
4/ 4 01 2.0
V/C
02 1.3
Supply current IS I
L = 0.0 mA 1 01 10.5 pA /
Hz
02 9.5
2,3 01 13.0
02 11.5
Large signal voltage gain AVOL V
OUT = 12 V, 4 01 5.0
V/V
RL 2.0 k 02 7.0
VOUT = 10 V, 5,6 01 2.0
RL 2.0 k 02 3.0
VOUT = 10 V, 4 01 3.5
RL 1.0 k 02 5.0
5,6 01 1.5
02 2.0
VOUT = 10 V, 4 01 2.0
RL 600 02 3.0
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-88622
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
D SHEET 7
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics – Continued.
Test Symbol Conditions
-55C TA +125C
unless otherwise specified
Group A
subgroups
Device
type
Limits Unit
Min Max
Common mode rejection
ratio CMRR VCM = 11.0 V 1 01 110 dB
02 114
VCM = 10.3 V 2,3 01 100
02 106
Power supply rejection
ratio PSRR 4.0 V VS 18 V 1 01 110 dB
02 117
4.5 V VS 16 V 2,3 01 104
02 110
1/ Input offset voltage measurement are performed by automatic test equipment approximately 0.5 seconds after application
of power.
2/ This test is guaranteed by the CMRR test.
3/ Current noise is defined an d measured with balanced source resistors. The resultant voltage nois e (after subtracting the
resistor noise on an rms basis) is divided by the sum of the two source resistors to obtain current noise.
4/ If not tested, shall be guaranteed to the limits specifie d in table I.
4. VERIFICATION
4.1 Sampling and inspection. Sampling an d inspection procedures shall be in accordance with MIL-PRF - 38535,
appendix A.
4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on al l devices
prior to quality conformance inspection. The following additional criteria shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to the preparing or ac quiring activity upon request. The test circuit shall s pecify
the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method
1015 of MIL-STD-883.
(2) TA = +125C, minimum.
b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-88622
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
D SHEET 8
DSCC FORM 2234
APR 97
Case outline X
FIGURE 1. Case outline.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-88622
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
D SHEET 9
DSCC FORM 2234
APR 97
Case outline X - continued
Symbol Dimensions Notes
Inches Millimeters
Min Max Min Max
A .165 .185 4.19 4.70
b1 .016 .021 .41 .53 2
b2 .016 .024 .41 .61
D .335 .370 8.51 9.40
D1 .305 .335 7.75 8.51
D2 .110 .160 2.79 4.06
e .230 BSC 5.84 BSC
F --- .040 --- 1.02
K .028 .034 .71 .86
K1 .027 .045 .69 1.14 3
L .500 .750 12.70 19.05 2
L1 --- .050 --- 1.27 2
Q .010 .045 .25 1.14
45 45 4
Note 1, 5, 6
NOTES:
1/ The U.S. government preferred system of measurement is the metric SI system. However, since this item was
originally designed using inch-pound units of measurement, in the eve nt of conflict between the metric and
inch- pound units, the inch-pound units shall take precedence.
2/ Diameter is uncontrolled in L1 and beyo nd form the reference plane.
3/ Measured from maximum diameter of the product.
4/ is the basic spacing from the centerline of the tab to terminal 1, looking at the bottom of the package.
5/ Leads having a maximum diameter .019 inch (0.48 mm) measur ed in gauging plane .054 inch (1.37 mm) + .001 inch
(0.02 mm) - .000 inc h (0.00 mm) inches below the base plane of the pr oduct shall be within .007 inch (0.17 mm) of
their true pos ition relative to a maximum width tab.
6/ This style package may be measured by direct methods or by gauge.
FIGURE 1. Case outline – continued.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-88622
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
D SHEET 10
DSCC FORM 2234
APR 97
Device types 01 and 02
Case outlines G, P, and X
Terminal
number Terminal symbol
1 VOS TRIM
2 -INPUT
3 +INPUT
4 -VS
5 OVER – COMP
6 OUTPUT
7 +VS
8 VOS TRIM
FIGURE 2. Terminal connections.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-88622
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
D SHEET 11
DSCC FORM 2234
APR 97
TABLE II. Electrical test requirements.
MIL-STD-883 test requirements Subgroups
(in accordance with
MIL-STD-883, method 5005,
table I)
Interim electrical parameters
(method 5004) ---
Final electrical test parameters
(method 5004) 1*, 2, 3, 4, 5, 6
Group A test requirements
(method 5005) 1, 2, 3, 4, 5, 6, 7
Groups C and D end-point
electrical parameters
(method 5005)
1
* PDA applies to subgroup 1 except for the input offset voltage test.
4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of
MIL-STD-883 including groups A, B, C, and D inspections. The following additional criter ia shall apply.
4.3.1 Group A inspection.
a. Tests shall be as specifi ed in table II herein.
b. Subgroups 8, 9, 10, and 11 in table I, method 5005 of MIL-ST D-883 shall b e omitted.
4.3.2 Groups C and D inspe c tions.
a. End-point electrical p arameters shall be as specified in table II herein.
b. Steady-state life test conditions, method 1005 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision
level control and shall be ma de available to the preparing or acquiring activity upon request. T he test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordanc e with the intent specified in
method 1005 of MIL-STD-883.
(2) TA = +125C, minimum.
(3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
5. PACKAGING
5.1 Packaging requirements. The requir ements for packaging shall be in accordance with MIL-PRF-38535, appendix A.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-88622
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
D SHEET 12
DSCC FORM 2234
APR 97
6. NOTES
6.1 Intended use. Microcircuits conforming t o this drawing are intended for use for Government microcircuit applications
(original equipment), desig n applications, and logistics purposes.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-
prepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for
the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.
6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires
configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this
list will be used for coordination and distribution of cha nges to the drawings. Users of drawings covering microelectronics
devices (FSC 5962) should c ontact DLA Land and Maritime-VA, telephone (614) 6 92-8108.
6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990,
or telephone (614) 692-0540.
6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103 and QML-38535. The vendors
listed in MIL-HDBK-103 and QML-38535 h ave agreed to this drawing and a certificate of compliance (see 3.6 herein) has been
submitted to and accepted by DLA Land and Maritime-VA.
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 15-05-19
Approved sources of suppl y for SMD 5962-88622 are list ed below for immediate acquisition information only and
shall be added to MIL-HDBK-103 an d QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DLA Land and Maritime-VA. This information
bulletin is superseded by the ne xt dated revision of MIL-HDBK-103 and QML-38535. DLA Land and Maritime
maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-8862201GA 3/ LT1028MH/883
5962-8862201PA 60264 MTLT1028QD8
3/ LT1028MJ8/883
5962-8862201XA 60264 MTLT1028QH
3/ LT1028MH/883
5962-8862202GA 3/ LT1028AMH/883
5962-8862202PA 60264 MTLT1028AQD8
3/ LT1028AMJ8/883
5962-8862202XA 60264 MTLT1028AQH
3/ LT1028AMH/883
1/ The lead finish shown for each PIN representing
a hermetic package is the most readily available
from the manufacturer listed for that part. If the
desired lead finish is not listed contact the vendor
to determine its availability.
2/ Caution. Do not use this number for item
acquisition. Items acquired to this number m ay not
satisfy the performance requirements of this drawing.
3/ Not available from an approved source of supply.
Vendor CAGE Vendor name
number and address
60264 Minco Technology La bs, Inc.
1805 Rutherford Lan e
Austin, TX 78754-5101
The information contained herein is disseminated for conveni ence only and the
Government assumes no liability whatsoeve r for any inaccuracies in the
information bulletin.