IE-78K4-NS - NEC Electronics

User’s Manual

IE-78K4-NS

In-Circuit Emulator

Target Devices

78K/IV Series

Document No. U13356EJ3V0UM00 (3rd edition)

Date Published May 2003 N CP(K)

Printed in Japan

User’s Manual U13356EJ3V0UM

[MEMO]

User’s Manual U13356EJ3V0UM 3

V40 Family is a trademark of NEC Electronics Corporation.

Windows is either a registered trademark or trademark of Microsoft Corporation in the United States and/or

other countries.

PC/AT is a trademark of International Business Machines Corporation.

The information in this document is current as of February, 2003. The information is subject to

change without notice. For actual design-in, refer to the latest publications of NEC Electronics data

sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not

all products and/or types are available in every country. Please check with an NEC Electronics sales

representative for availability and additional information.

No part of this document may be copied or reproduced in any form or by any means without the prior

written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may

appear in this document.

NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual

property rights of third parties by or arising from the use of NEC Electronics products listed in this document

or any other liability arising from the use of such products. No license, express, implied or otherwise, is

granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others.

Descriptions of circuits, software and other related information in this document are provided for illustrative

purposes in semiconductor product operation and application examples. The incorporation of these

circuits, software and information in the design of a customer's equipment shall be done under the full

responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by

customers or third parties arising from the use of these circuits, software and information.

While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products,

customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To

minimize risks of damage to property or injury (including death) to persons arising from defects in NEC

Electronics products, customers must incorporate sufficient safety measures in their design, such as

redundancy, fire-containment and anti-failure features.

NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and

"Specific".

The "Specific" quality grade applies only to NEC Electronics products developed based on a customer-

designated "quality assurance program" for a specific application. The recommended applications of an NEC

Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of

each NEC Electronics product before using it in a particular application.

The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC

Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications

not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to

determine NEC Electronics' willingness to support a given application.

(Note)

•

M8E 02. 11-1

(1)

(2)

"NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its

majority-owned subsidiaries.

"NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as

defined above).

Computers, office equipment, communications equipment, test and measurement equipment, audio

and visual equipment, home electronic appliances, machine tools, personal electronic equipment

and industrial robots.

Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster

systems, anti-crime systems, safety equipment and medical equipment (not specifically designed

for life support).

Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life

support systems and medical equipment for life support, etc.

"Standard":

"Special":

"Specific":

User’s Manual U13356EJ3V0UM

Regional Information

•

Device availability

•

Ordering information

•

Product release schedule

•

Availability of related technical literature

•

Development environment specifications (for example, specifications for third-party tools and

components, host computers, power plugs, AC supply voltages, and so forth)

•

Network requirements

In addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary

from country to country.

[GLOBAL SUPPORT]

http://www.necel.com/en/support/support.html

NEC Electronics America, Inc. (U.S.)

Santa Clara, California

Tel: 408-588-6000

800-366-9782

NEC Electronics Hong Kong Ltd.

Hong Kong

Tel: 2886-9318

NEC Electronics Hong Kong Ltd.

Seoul Branch

Seoul, Korea

Tel: 02-558-3737

NEC Electronics Shanghai, Ltd.

Shanghai, P.R. China

Tel: 021-6841-1138

NEC Electronics Taiwan Ltd.

Taipei, Taiwan

Tel: 02-2719-2377

NEC Electronics Singapore Pte. Ltd.

Novena Square, Singapore

Tel: 6253-8311

J03.4

EC Electronics (Europe) GmbH

Duesseldorf, Germany

Tel: 0211-65 03 01

• Sucursal en España

Madrid, Spain

Tel: 091-504 27 87

Vélizy-Villacoublay, France

Tel: 01-30-67 58 00

• Succursale Française

• Filiale Italiana

Milano, Italy

Tel: 02-66 75 41

• Branch The Netherlands

Eindhoven, The Netherlands

Tel: 040-244 58 45

• Tyskland Filial

Taeby, Sweden

Tel: 08-63 80 820

• United Kingdom Branch

Milton Keynes, UK

Tel: 01908-691-133

Some information contained in this document may vary from country to country. Before using any NEC

Electronics product in your application, pIease contact the NEC Electronics office in your country to

obtain a list of authorized representatives and distributors. They will verify:

User’s Manual U13356EJ3V0UM 5

Major Revisions in This Edition

Page Description

Throughout Change of interface board for desktop PC from IE-700000-PCI-IF to IE-70000-PCI-A

p.12 Modification of Figure 1-1 IE-78K4-NS System Configuration

p.28 A.1 Introduction

•Deletion of Applicable models

p.30 B.1 Introduction

•Deletion of Applicable models

The mark shows major revised points.

User’s Manual U13356EJ3V0UM

INTRODUCTION

Product Overview The IE-78K4-NS is used in combination with an I/O emulation board (IE-

784×××-NS-EM1) to debug products of the 78K/IV Series of 16-bit single-chip

microcontrollers.

Target Readers This manual is intended for engineers who will perform debugging of systems

that employ 78K/IV Series 16-bit single-chip microcontrollers using the IE-78K4-

NS in combination with an I/O emulation board (IE-784×××-NS-EM1).

Purpose The purpose of this manual is to help the reader understand the debugging

functions that are available by using the IE-78K4-NS and the I/O emulation

board (IE-784×××-NS-EM1) together.

Organization When using the IE-78K4-NS, refer to the manual (this manual) that comes with

the IE-78K4-NS as well as the manual that comes with the I/O emulation board

(IE-784×××-NS-EM1).

• Basic specifications • Function outline

• System configuration • Target interface differences

• External interface function

How to Read This Manual To understand the overall functions of the IE-78K4-NS

→ Read this manual in the order of the CONTENTS.

To understand the basic specifications

→ Refer to CHAPTER 1 GENERAL and CHAPTER 2 PART NAMES.

To know the appropriate settings when debugging 78K/IV Series products while

connected to the IE-784×××-NS-EM1

→ Refer to CHAPTER 3 INSTALLATION.

IE-78K4-NS

User’s Manual

(This manual)

IE-784×××-NS-EM1

User’s Manual

User’s Manual U13356EJ3V0UM 7

Terminology The meanings of the terms used in this manual are described in the table below.

Term Meaning

Emulation device Refers to the generic name for the device in the emulator that performs emulation of the target device.

This includes the emulation CPU.

Emulation CPU Refers to the CPU block that executes the user’s program in the emulator.

Target device Refers to the device to be emulated.

Target program Refers to the program to be debugged.

Target system Refers to the system to be debugged.

This includes the target program and the hardware created by the user. In the narrow sense, it means

hardware only.

Conventions Data significance: Higher digits on the left and lower digits on the right

Note: Footnote for item marked with Note in the text

Caution: Information requiring particular attention

Remark: Supplementary information

Related Documents Please use the following documents in conjunction with this manual.

The related documents listed below may include preliminary versions. However,

preliminary versions are not marked as such.

{Documents Related to Development Tools (User’s Manuals)

Document Name Document Number

IE-78K4-NS In-Circuit Emulator This manual

Operation U15254E

Language U15255E

RA78K4 Assembler Package

Structured Assembler Preprocessor U11743E

Operation U15557ECC78K4 C Compiler Package

Language U15556E

Operation (WindowsTM Based) U15373ESM78K Series System Simulator Ver.2.30 or later

External part user open

interface specifications

U15802E

ID78K Series Integrated Debugger Ver.2.30 or

later

Operation (Windows Based) U15185E

Basics U10603E

Installation U10604E

RX78K4 Real-Time OS

Debugger −

Project Manager Ver. 3.12 or later (Windows Based) U14610E

PG-FP4 Flash Memory Programmer U15260E

Caution The documents listed above are subject to change without notice. Be sure to use the latest

documents for designing.

User’s Manual U13356EJ3V0UM

CONTENTS

CHAPTER 1 GENERAL.................................................................................................................... 11

1.1 System Configuration ..........................................................................................................................11

1.2 Hardware Configuration.......................................................................................................................13

1.3 Basic Specifications ............................................................................................................................14

1.4 Package Contents ................................................................................................................................16

CHAPTER 2 PART NAMES............................................................................................................. 18

2.1 Parts of Main Unit................................................................................................................................. 18

2.2 Board Name ..........................................................................................................................................20

CHAPTER 3 INSTALLATION ........................................................................................................... 22

3.1 Connection............................................................................................................................................22

3.2 External Trigger Functions ..................................................................................................................26

3.3 Jumper Setting (on Emulation Board (G-78K4 EM Board)) ..............................................................26

CHAPTER 4 RESTRICTIONS WHEN DETECTING TRACE EVENT ........................................... 27

APPENDIX A INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC ......................... 28

A.1 Introduction .......................................................................................................................................... 28

A.2 Installation ............................................................................................................................................29

APPENDIX B PC CARD INTERFACE (IE-70000-CD-IF-A) .......................................................... 30

B.1 Introduction .......................................................................................................................................... 30

B.2 Installation ............................................................................................................................................31

APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES ...................... 32

C.1 Introduction .......................................................................................................................................... 32

C.2 Installation ............................................................................................................................................33

APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT AND

COMPATIBLES .......................................................................................................... 35

D.1 Introduction .......................................................................................................................................... 35

D.2 Installation ............................................................................................................................................36

APPENDIX E REVISION HISTORY .................................................................................................38

User’s Manual U13356EJ3V0UM 9

LIST OF FIGURES

Figure No. Title Page

1-1 IE-78K4-NS System Configuration ..............................................................................................................12

1-2 Basic Hardware Configuration of IE-78K4-NS .............................................................................................13

1-3 Package Contents .......................................................................................................................................16

1-4 Contents of Accessory Bag .........................................................................................................................17

2-1 Main Board (G-78K4 MAIN Board) ..............................................................................................................20

2-2 Emulation Board (G-78K4 EM Board)..........................................................................................................21

3-1 Connecting I/O Emulation Board .................................................................................................................23

3-2 Connecting Emulation Probe .......................................................................................................................24

3-3 Connecting AC Adapter ...............................................................................................................................25

3-4 Connecting Dedicated Bus Interface Cable.................................................................................................25

A-1 Mounting PCI Board and Connector Board .................................................................................................29

C-1 Settings of INT JP and WAIT JP..................................................................................................................34

D-1 Settings of INT JP and WAIT JP..................................................................................................................37

User’s Manual U13356EJ3V0UM

LIST OF TABLES

Table No. Title Page

1-1 List of Functions (MAX. Specifications)........................................................................................................14

3-1 Electrical Specifications ...............................................................................................................................26

C-1 SW1 and SW2 Settings When Using IE-78K4-NS.......................................................................................33

D-1 SW1 and SW2 Settings When Using IE-78K4-NS.......................................................................................36

User’s Manual U13356EJ3V0UM 11

CHAPTER 1 GENERAL

The IE-78K4-NS is a development tool for effective debugging of hardware and software using a 78K/IV Series 16-

bit single-chip microcontroller.

This chapter describes the system configuration and basic specifications of the IE-78K4-NS.

1.1 System Configuration

Figure 1-1 shows the system configuration of the IE-78K4-NS.

CHAPTER 1 GENERAL

User’s Manual U13356EJ3V0UM

Figure 1-1. IE-78K4-NS System Configuration

Conversion socket

EV-××××××-×××

TQ×-××××××Note 3

(Sold separately)

Integrated debugger

ID78K4-NS

(Sold separately)

Device file

(Available separately)

Control software

Host machine

PC-9800 series or

IBM PC/ATTM compatible

Interface board

IE-70000-98-IF-C

(Sold separately)

Interface board

IE-70000-PC-IF-C

(Sold separately)

IE-78K4-NS

(This product)

Interface cable

(NS interface cable)

In-circuit

emulator

FC cable

PC card interface

Interface cable

NS card

cable

MC card

cable

Note 1

PC card interface

IE-70000-CD-IF-A

(Sold separately)

AC adapter

IE-70000-MC-PS-B

(Sold separately)

I/O emulation board

IE-784×××-NS-EM1

(Sold separately)

Emulation probe

NP-×××××Note 2

(Sold separately)

Interface board

IE-70000-PCI-IF-A

(Sold separately)

Notes 1. This cable is used for the V850 FamilyTM. It cannot be used for the IE-78K4-NS.

2. The NP-××××× is a product of Naito Densei Machida Mfg. Co., Ltd. For further information, contact

Naito Densei Machida Mfg. Co., Ltd. (TEL: +81-45-475-4191)

3. The TQ×-×××××× is a product of TOKYO ELETECH CORPORATION.

Inquiries: Daimaru Kogyo, Ltd.

Tokyo Electronics Department (TEL: +81-3-3820-7112)

Osaka Electronics Department (TEL: +81-6-6244-6672)

4. The device file can be downloaded from the NEC Electronics Website.

(URL: http://www.necel.com/micro).

CHAPTER 1 GENERAL

User’s Manual U13356EJ3V0UM 13

1.2 Hardware Configuration

The IE-78K4-NS consists of the following hardware units (such as cabinet and boards).

• Cabinet

• 78K4 main board

• 78K4 emulation board

• NS interface cable

Figure 1-2. Basic Hardware Configuration of IE-78K4-NS

Emulation probe

(Sold separately)

Host

machine

Interface

board

(Sold

separately)

Interface

card

(Sold

separately)

Dedicated

bus interface

78K4 main

board

78K4

emulation

board

I/O emulation board

IE-784×××-NS-EM1

(Sold separately)

IE-78K4-NS

IE-784

×××

-NS-EM1

CHAPTER 1 GENERAL

User’s Manual U13356EJ3V0UM

1.3 Basic Specifications

Table 1-1. List of Functions (MAX. Specifications) (1/2)

Parameter Description

Supervisor V40TM (operating frequency: 9.8304 MHZ)

Target device

PD784××× Series

System clock Same as target device

External Pulse inputClock supply

Internal Mounted on IE-784×××-NS-EM1

Substitute memory capacity 1 MB

Internal ROM 8 KB

External RAM 512 bytes

Peripheral RAM 256 bytes

Mapping unit

External substitute

memory

• 64 KB space or less: 4 KB

• 1 MB space or less: 64 KB

• 1 MB space or more: 1 MB

Emulation function • Real-time execution

• Break execution

• Step execution

Real-time internal RAM monitor All internal RAM area

Event detection • Program execution detection

• Bus event detection

• External trigger detection

Trigger output (1 unit) and open-drain output

Event integration • Path condition

• Sequential condition

• Trace qualify condition

• Section trace start/end condition (time measurement counter start/end)

•

••

• Trigger output condition (trace delay)

Break factor • Event break

• Manual break

• Command break

• Fail-safe break

Trace factor • All trace

• Section trace

• Qualify trace

Trace capacity 96 bits × 32 KB

Real-time trace

Trace content Address, data, and status

CHAPTER 1 GENERAL

User’s Manual U13356EJ3V0UM 15

Table 1-1. List of Functions (MAX. Specifications) (2/2)

Parameter Description

Execution time measurement Up to 14 min. 33 sec., resolution: 203.45 ns

Number of measured section executions: 65536 MAX.

Target interface Emulation probe (sold separately) provided for each target device shape

Pin mask RESET, HLDRQ, NMI, WAIT, and Hardware STOP are maskable

Host interface Dedicated bus interface

Low-voltage support Based on the I/O emulation board (sold separately)

Host machine PC-9800 series and PC/AT compatibles

Power supply DC 5 V

Dimensions W240 × D197 × H73 (mm)

CHAPTER 1 GENERAL

User’s Manual U13356EJ3V0UM

1.4 Package Contents

The packing box of the IE-78K4-NS contains the main unit, cables, an accessory bag, and a guarantee card.

A detailed list of contents, this user’s manual, and screws are in the accessory bag. If anything is missing or

broken, contact an NEC Electronics sales representative or an NEC Electronics distributor.

Figure 1-3. Package Contents

<1> IE-78K4-NS main unit: 1

<2> NS interface cable: 1

<3> FG cable: 1

<4> Accessory bag: 1

<5> Guarantee card: 1

<2> NS interface cable <3> FG cable

<4> Accessory bag

<1> IE-78K4-NS

<5> Guarantee card

CHAPTER 1 GENERAL

User’s Manual U13356EJ3V0UM 17

Make sure that the following items are contained in the accessory bag (see Figure 1-4 Contents of the Accessory

Bag).

<a> Detailed list of contents: 1

<b> User’s manual (this manual): 1

<c> Screws: 4

Figure 1-4. Contents of Accessory Bag

<a> Detailed list of contents

<b> User's manual

<c> Screws

User’s Manual U13356EJ3V0UM

CHAPTER 2 PART NAMES

This chapter introduces the parts of the IE-78K4-NS main unit.

The packing box contains the IE-78K4-NS main unit. If anything is missing or damaged, please contact an NEC

Electronics sales representative.

Please make sure to fill out and return the guarantee card that comes with the main unit.

2.1 Parts of Main Unit

(1) Probe end

(2) Top view

T V C C

Target system power supply LED

Probe interface

POWER

IN CIRCUIT EMULATOR

Power supply LED

CHAPTER 2 PART NAMES

User’s Manual U13356EJ3V0UM 19

(3) Interface end

FG OFF ON RESET HOST-I/F

DC IN

Reset switch

(RESET)

Dedicated bus interface connector

(HOST-I/F)

Power switch

(OFF/ON)

CHAPTER 2 PART NAMES

User’s Manual U13356EJ3V0UM

2.2 Board Name

IE-78K4-NS contains two boards.

• Main board (G-78K4 MAIN Board): 1

• Emulation board (G-78K4 EM Board): 1

Check that you have the correct two boards. To access the inside of the unit, remove the four screws from the

sides of the main unit and open the lid.

Figure 2-1. Main Board (G-78K4 MAIN Board)

Remark The main board is shown mounted in the main unit.

CHAPTER 2 PART NAMES

User’s Manual U13356EJ3V0UM 21

Figure 2-2. Emulation Board (G-78K4 EM Board)

User’s Manual U13356EJ3V0UM

CHAPTER 3 INSTALLATION

This chapter explains how to connect the cables to the IE-78K4-NS and the mode settings.

3.1 Connection

Connect the following seven products, which are sold separately.

Refer to Figure 1-1 IE-78K4-NS System Configuration in CHAPTER 1 GENERAL for the system configuration

of the IE-78K4-NS.

• IE-70000-98-IF-C: Interface board (Use cable that comes with IE-78K4-NS)

• IE-70000-PC-IF-C: Interface board (Use cable that comes with IE-78K4-NS)

• IE-70000-PCI-IF-A: Interface board (Use cable that comes with IE-78K4-NS)

• IE-70000-CD-IF-A: PC card interface (Use NS card cable)

• IE-70000-MC-PS-B: AC adapter

• IE-784×××-NS-EM: I/O emulation board

• NP-×××××: Emulation probe

Caution Connecting and removing cables or components from the target system and changing the

settings of switches, etc. must be carried out after turning off the power of the IE-78K4-NS main

unit and the target system.

CHAPTER 3 INSTALLATION

User’s Manual U13356EJ3V0UM 23

(1) Connecting I/O emulation board (IE-784×××

××××××

×××-NS-EM1)

IE-784×××-NS-EM1 is sold separately.

Figure 3-1. Connecting I/O Emulation Board

<1> Remove the screws from the sides of the

main unit, and then remove the top cover.

<2> Remove the second plate from the bottom

by removing the screws.

<3> Remove the four screws from the top of the

emulation board, connect the IE-784×××-

NS-EM1 and then tighten the screws.

<4> Connect the relevant probe. <5> Connect the top cover and tighten the four

screws on the sides.

;;

;;;

;;

;

Emulation board

;

;;

I/O emulation board

Refer to (2) for probe connection

CHAPTER 3 INSTALLATION

User’s Manual U13356EJ3V0UM

(2) Connecting emulation probe (NP-×××××

××××××××××

×××××)

NP-××××× is sold separately.

Figure 3-2. Connecting Emulation Probe

Caution The emulation probe (NP-×××××

××××××××××

×××××) mounting location varies depending on the model of the I/O

emulation board (IE-784×××

××××××

×××-NS-EM1) in use. For details, refer to the IE-784×××

××××××

×××-NS-EM1 User’s

Manual.

;

;;

;

;;

;

Emulation board

(G-78K4 EM Board)

Emulation probe

(NP-××××× )

I/O emulation board

(IE-784×××-NS-EM1)

Main board

(G-78K4 MAIN Board)

CHAPTER 3 INSTALLATION

User’s Manual U13356EJ3V0UM 25

(3) Connecting AC adapter (IE-70000-MC-PS-B)

IE-70000-MC-PS-B is sold separately.

<1> Insert the AC adapter plug into the DC IN socket on the interface end of the IE-78K4-NS.

Figure 3-3. Connecting AC Adapter

(4) Connecting interface cable

<1> Insert the cable into the dedicated bus interface connector on the interface end of the IE-78K4-NS.

Figure 3-4. Connecting Dedicated Bus Interface Cable

Caution The type of interface cable varies depending on the interface board and PC card interface.

• When using an interface board (IE-70000-98-IF-C, IE-70000-PC-IF-C, or IE-70000-PCI-IF-A)

→

→→

→ Connect the NS interface cable that comes with the IE-78K4-NS.

•

••

• When using a PC card interface (IE-70000-CD-IF-A)

→

→→

→ Connect the NS card cable that comes with the IE-70000-CD-IF-A.

The IE-70000-98-IF-C, IE-70000-PC-IF-C, IE-70000-PCI-IF-A, and IE-70000-CD-IF-A are sold

separately.

FG OFF ON RESET HOST-I/F

DC IN

Reset switch

(RESET)

Dedicated bus interface connector

(HOST-I/F)

Power switch

(OFF/ON)

FG OFF ON RESET HOST-I/F

DC IN

Reset switch

(RESET)

Dedicated bus interface connector

(HOST-I/F)

Power switch

(OFF/ON)

CHAPTER 3 INSTALLATION

User’s Manual U13356EJ3V0UM

3.2 External Trigger Functions

(1) EXTOUT

At the occurrence of a break event, the EXTOUT pin on the I/O emulation board (IE-784×××-NS-EM1) outputs a

high level for a single CPU operating clock.

Caution Because the output is open drain, connect a pull-up resistor in the target system.

(2) EXTIN

The EXTIN pin on the I/O emulation board (IE-784×××-NS-EM1) can be used to input an event signal. Enter

high-level pulse signals for three or more CPU operating clocks.

Caution For the electrical specifications, refer to Table 3-1.

Table 3-1. Electrical Specifications

Parameter MIN. [V] MAX. [V]

High-level input voltage Target voltage × 0.7 Target voltage

Low-level input voltage 0 Target voltage × 0.3

3.3 Jumper Setting (on Emulation Board (G-78K4 EM Board))

Caution Use the default setting (2, 3 =

= shorted) for JP1.

JP1

1 2 3

Default setting : 2, 3 = Shorted

User’s Manual U13356EJ3V0UM 27

CHAPTER 4 RESTRICTIONS WHEN DETECTING TRACE EVENT

When the emulation CPU is operating at 16 MHZ or higher (when the X1 pin is supplied with a signal of 32 MHZ or

higher and the standby control register (STBC) is set to 00H), detection of the following three trace events may not be

performed normally.

• Vector read

• Macro service read

• Macro service write

User’s Manual U13356EJ3V0UM

APPENDIX A INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC

The settings when connecting the IE-78K4-NS are described below.

For details, refer to the IE-70000-PCI-IF-A User’s Manual (to be prepared).

A.1 Introduction

The IE-70000-PCI-IF-A is an interface board for the IE series, to be used mounted in the PCI bus slot.

First of all, check that you have following items.

• Interface board (IE-70000-PCI-IF-A) for desktop PC: 1

• 8-bit connector board (connected to IE-70000-PCI-IF): 1

• 32-bit connector board: 1

• User’s manual: 1

• DLL-DISK: 1

• DRV-DISK: 1

Hardware resources

• I/O address: 0000H to FFFFH

• Interrupt: Unused

• Memory: 80H bytes used

Current consumption

300 mA (MAX. @ +5 V)

Cautions 1. Do not place heavy objects on or apply pressure to the board.

2. Do not drop the board or subject it to excessive vibration or shock.

3. When removing a cable, be sure not to pull it by the cord.

4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it is

directly exposed to sunlight.

5. Avoid subjecting the board to extreme changes in temperature or humidity.

6. Be careful not to spill drinks or other liquids onto the board or its accessories.

7. Be careful not to connect a cable for a different product to the connector.

APPENDIX A INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC

User’s Manual U13356EJ3V0UM 29

A.2 Installation

(1) Board settings

The IE-70000-PCI-IF-A does not have jumper and DIP switches

(2) Mounting 8-bit connector board

The 8-bit connector board has been mounted before shipment.

Remark When mounting the 32-bit board, mount it on top of the 8-bit connector board using a coupling

connector (see Figure A-1). After mounting these boards, fix them tightly with screws.

Caution The 32-bit connector board is supplied for future function expansion. Be sure to store it

carefully.

Figure A-1. Mounting PCI Board and Connector Board

(3) Mounting in PC

After checking that the PC’s power is off, insert the interface board into the PCI bus slot following the instructions

in the PC’s user’s manual.

(4) Installation of PCI driver

Install the PCI driver referring to the DRV-DISK Readme_e.txt that comes with the IE-70000-PCI-IF.

(5) Connecting to IE-78K4-NS

Using the cable that comes with the IE-70000-PCI-IF, connect the IE-78K4-NS to CH0.

Caution Connection with the IE-78K4-NS is possible on the CH0 side only.

Coupling connector

CH1 CH0

32-bit connector board

8-bit connector boardPCI board

User’s Manual U13356EJ3V0UM

APPENDIX B PC CARD INTERFACE (IE-70000-CD-IF-A)

The settings when connecting the IE-78K4-NS are described below.

For details, refer to the IE-70000-CD-IF-A User’s Manual (to be prepared).

B.1 Introduction

The PC card interface (IE-70000-CD-IF-A) is an interface card to be used mounted in a PC card slot compliant with

PCMCIA2.1/JEIDA standard Ver.4.2.

First of all, check that you have following items.

• PC card interface (IE-70000-CD-IF-A): 1

• MC-A CABLE: 1

• NS-A CABLE: 1

• User’s manual: 1

• DLL-DISK: 1

• DRV-DISK: 1

Hardware resources

• I/O address: 20H bytes with base address of 220H, 260H, 2E0H, 320H, or 3E0H

• Interrupt: Unused

• Memory: Unused

Current consumption

300 mA (MAX. @ +5 V)

Cautions 1. Do not place heavy objects on or apply pressure to the card.

2. Do not drop the card or subject it to excessive vibration or shock.

3. When removing a cable, be sure not to pull it by the cord.

4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it is

directly exposed to sunlight.

5. Avoid subjecting the board to extreme changes in temperature or humidity.

6. Be careful not to spill drinks or other liquids onto the board or its accessories.

7. Be careful not to connect a cable for a different product to the connector.

APPENDIX B PC CARD INTERFACE (IE-70000-CD-IF-A)

User’s Manual U13356EJ3V0UM 31

B.2 Installation

(1) Mounting in PC

Insert the PCMCIA card into the card slot when the PC’s power is on.

For Windows NT 4.0, insert the card into the slot when the PC’s power is off. When inserting the card, make

sure that the card is facing the right way.

(2) Installation of PCMCIA driver

Install the PCMCIA driver referring to the DRV-DISK Readme_e.txt that comes with the IE-70000-CD-IF-A.

Caution This interface card cannot be connected to the IE-78××××

××××××××

××××-R. If the IE-78××××

××××××××

××××-R

displayed on the DRV-DISK installation menu is selected, the installation menu will close

normally but the installation is not valid.

(3) Connecting to IE-78K4-NS

Connect the IE-70000-CD-IF-A to the IE-78K4-NS using the NS-A CABLE.

Caution Be sure to use the NS-A CABLE when connecting to the IE-78K4-NS. If the MC-A CABLE is

used, the IE-70000-CD-IF-A may be damaged.

User’s Manual U13356EJ3V0UM

APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES

The settings when connecting the IE-78K4-NS are described below.

For details, refer to the IE-70000-98-IF-C User’s Manual (to be prepared).

C.1 Introduction

The IE-70000-98-IF-C is an interface board that is mounted in the C bus slot of the PC-9800 series.

Caution The PC98-NX Series is regarded as IBM PC/AT compatible. Refer to APPENDIX A INTERFACE

BOARD (IE-70000-PCI-IF) FOR DESKTOP PC.

First of all, check that you have the correct interface board.

• Interface board (IE-70000-98-IF-C) for PC-9800 series: 1

Applicable models

This product is designed to work with PC-9800 series devices equipped with a C bus.

Hardware resources

• I/O addresses: 16 bytes at the 256-byte boundary (00D×H, 01D×H,...FFD×H)

• Interrupts and other: Unused

Current consumption

500 mA (MAX. @ +5 V)

Cautions 1. Do not place heavy objects on or apply pressure to the board.

2. Do not drop the board or subject it to excessive vibration or shock.

3. When removing a cable, be sure not to pull it by the cord.

4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it is

directly exposed to sunlight.

5. Avoid subjecting the board to extreme changes in temperature or humidity.

6. Be careful not to spill drinks or other liquids onto the board or its accessories.

7. Be careful not to connect a cable for a different product to the connector.

APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES

User’s Manual U13356EJ3V0UM 33

C.2 Installation

(1) I/O address settings

SW1 and SW2 are the switches for selecting the C bus I/O addresses. SW1 numbers 1 to 8 correspond to C bus

addresses A4 to A11, and SW2 numbers 1 to 4 correspond to C bus addresses A12 to A15.

In the IE-78K4-NS, the addresses should be set in the 16 bytes between 00D×H and FFD×H. The switch takes

the value “0” when ON and “1” when OFF.

The addresses to be set must be values that are not used in the PC system or for other boards. In addition,

since these values are used during software installation, make a note of them for future reference.

Table C-1. SW1 and SW2 Settings When Using IE-78K4-NS

SW1 Number12345678

Address A4 A5 A6 A7 A8 A9 A10 A11 I/O Address

ON 0000

01D×H

OFF 1 111

SW2 Number12345678

Address A12 A13 A14 A15 OFF OFF ON OFF I/O Address

ON 0 000 0 01D×H

OFF 1 1 1

Cautions 1. Use the default setting for SW1 numbers 1 to 4.

2. Set SW2 number 7 to ON and SW2 numbers 5, 6, and 8 to OFF.

APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES

User’s Manual U13356EJ3V0UM

(2) Jumper settings

INT JP and WAIT JP are jumpers that select C bus interrupt and WAIT.

For the IE-78K4-NS, set INT JP to NO USE, and WAIT JP to 1-2 shorted.

Figure C-1. Settings of INT JP and WAIT JP

(3) Mounting in PC

Make sure that the PC is turned off, then insert the interface board into the C bus slot following the instructions in

the PC’s user’s manual.

(4) Connecting with IE-78K4-NS

Using the supplied cable, connect the IE-78K4-NS to the CH0 side.

Caution Connection with the IE-78K4-NS is possible on the CH0 side only.

For connection with other models, refer to their respective user’s manuals.

WAIT JP

1 2 3

INT JP

: Shorted

Shorted

NO USE

IR3

IR5

IR6

IR9

IR11

IR12

IR13

User’s Manual U13356EJ3V0UM 35

APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT AND COMPATIBLES

The settings when connecting IE-78K4-NS are described below.

For details, refer to the IE-70000-PC-IF-C User’s Manual (to be prepared).

D.1 Introduction

The IE-70000-PC-IF-C is an interface board that is mounted in the ISA bus slot of an IBM PC/AT or compatible.

First of all, check that you have the correct interface board.

• Interface board (IE-70000-PC-IF-C) for IBM PC/AT: 1

Applicable models

The IE-70000-PC-IF-C is designed for IBM PC/AT and compatibles equipped with an ISA bus.

Hardware resources

• I/O address: 16 bytes at any 16-byte boundary (020×H to 03F×H)

• Interrupts and other: Unused

Current consumption

500 mA (MAX. @ +5 V)

Cautions 1. Do not place heavy objects on or apply pressure to the board.

2. Do not drop the board or subject it to excessive vibration or shock.

3. When removing a cable, be sure not to pull it by the cord.

4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it is

directly exposed to sunlight.

5. Avoid subjecting the board to extreme changes in temperature or humidity.

6. Be careful not to spill drinks or other liquids onto the board or its accessories.

7. Be careful not to connect a cable for a different product to the connector.

APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT AND COMPATIBLES

User’s Manual U13356EJ3V0UM

D.2 Installation

(1) I/O address settings

SW1 and SW2 are the switches for selecting the ISA bus I/O addresses. SW1 numbers 1 to 8 correspond to ISA

bus addresses A4 to A11, and SW2 numbers 1 to 4 correspond to ISA bus addresses A12 to A15.

In the IE-78K4-NS, the addresses should be set between 020×H and 03F×H. The switch takes the value “0”

when ON and “1” when OFF.

The addresses to be set must be values that are not used in the PC system or for other boards. In addition,

since these values are used during software installation, make a note of them for future reference.

Table D-1. SW1 and SW2 Settings When Using IE-78K4-NS

SW1 Number12345678

Address A4 A5 A6 A7 A8 A9 A10 A11 I/O Address

ON 0 0000 00

020×H

OFF 1

SW2 Number12345678

Address A12 A13 A14 A15 OFF OFF ON OFF I/O Address

ON 0 000 0 020×H

OFF 1 1 1

Caution Set SW2 numbers 1 to 4 and 7 to ON and SW2 numbers 5, 6, and 8 to OFF.

APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT AND COMPATIBLES

User’s Manual U13356EJ3V0UM 37

(2) Jumper settings

INT JP and WAIT JP are jumpers that select C bus interrupt and WAIT.

For the IE-78K4-NS, set INT JP to NO USE, and WAIT JP to 1-2 shorted.

Figure D-1. Settings of INT JP and WAIT JP

(3) Mounting in PC

Make sure that the PC is turned off, then insert the interface board into the ISA bus slot following the instructions

in the PC’s user’s manual.

(4) Connecting with IE-78K4-NS

Using the supplied cable, connect the IE-78K4-NS to the CH0 side.

Caution Connection with the IE-78K4-NS is possible on the CH0 side only.

For connection with other models, refer to their respective user’s manuals.

WAIT JP

1 2 3

INT JP

: Shorted

Shorted

NO USE

IRQ2

IRQ3

IRQ4

IRQ5

IRQ6

IRQ7

User’s Manual U13356EJ3V0UM

APPENDIX E REVISION HISTORY

The revisions up to this edition are shown in the table below.

Edition Revisions from Previous Edition Revised Chapters

Addition of 1.4 Package Contents CHAPTER 1 GENERAL

Addition of APPENDIX A INTERFACE BOARD (IE-70000-PCI-IF) FOR DESKTOP PC APPENDIX A

Addition of APPENDIX B PC CARD INTERFACE (IE-70000-CD-IF-A) APPENDIX B

Addition of explanation in APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR

PC-9800 SERIES

APPENDIX C

Addition of explanation in APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR

IBM PC/AT AND COMPATIBLES

APPENDIX D

2nd

Addition of APPENDIX E REVISION HISTORY APPENDIX E

Change of interface board for desktop PC from IE-70000-PCI-IF to IE-70000-PCI-IF-A Throughout

Modification of Figure 1-1 IE-78K4-NS System Configuration CHAPTER 1 GENERAL

A.1 Introduction

•

••

•Deletion of Applicable models

APPENDIX A

3rd

B.1 Introduction

•

••

•Deletion of Applicable models

APPENDIX B

User’s Manual U13356EJ3V0UM 39

[MEMO]