DS1340 I2C RTC with Trickle Charger
General Description
The DS1340 is a real-time clock (RTC)/calendar that is
pin compatible and functionally equivalent to the ST
M41T00, including the software clock calibration. The
device additionally provides trickle-charge capability
on the VBACKUP pin, a lower timekeeping voltage, and
an oscillator STOP flag. Block access of the register
map is identical to the ST device. Two additional regis-
ters, which are accessed individually, are required for
the trickle charger and flag. The clock/calendar pro-
vides seconds, minutes, hours, day, date, month, and
year information. A built-in power-sense circuit detects
power failures and automatically switches to the back-
up supply. Reads and writes are inhibited while the
clock continues to run. The device is programmed seri-
ally through an I2C bidirectional bus.
Applications
Portable Instruments
Point-of-Sale Equipment
Medical Equipment
Telecommunications
Benefits and Features
Enhanced Second Source for the ST M41T00
Completely Manages All Timekeeping Functions
RTC Counts Seconds, Minutes, Hours, Day, Date,
Month, and Year
Software Clock Calibration
Oscillator Stop Flag
Low-Power Operation Extends Battery Backup Run
Time
Low Timekeeping Voltage Down to 1.3V
Automatic Power-Fail Detect and Switch Circuitry
Trickle-Charge Capability
Three Operating Voltage Ranges (1.8V, 3V, and 3.3V)
Supports Systems Using Legacy and Modern Power
Buses
Surface-Mount Package with an Integrated Crystal
(DS1340C) Saves Additional Space and Simplifies
Design
Simple Serial Port Interfaces with Most Microcontrollers
Fast (400kHz) I2C Interface
8-Pin µSOP or SO Package Minimizes Required
Space
Underwriters Laboratories (UL®) Recognized
Ordering Information
4
CPU
VCC
VCC
VCC
5
6
8
12
SDA
SCL
GND
X2X1
VCC
C1
RPU RPU
CRYSTAL
FT/OUT
VBACKUP
3
7
RPU = tR / CB
DS1340
Typical Operating Circuit
PART TEMP RANGE PIN-
PACKAGE TOP MARK
DS1340Z-18+ -40°C to +85°C 8 SO
(0.150in) D1340-18
DS1340Z-3+ -40°C to +85°C
8 SO
(0.150in) DS1340-3
DS1340Z-33+ -40°C to +85°C 8 SO
(0.150in) D134033
DS1340U-18+ -40°C to +85°C 8 μSOP 1340 -18
DS1340U-3+ -40°C to +85°C 8 μSOP 1340 -3
DS1340U-33+ -40°C to +85°C 8 μSOP 1340 -33
DS1340C-18# -40°C to +85°C 16 SO DS1340C-18
DS1340C-3# -40°C to +85°C 16 SO DS1340C-3
DS1340C-33# -40°C to +85°C 16 SO DS1340C-33
Pin Configurations appear at end of data sheet.
+
Denotes a lead(Pb)-free/RoHS-compliant package.
#
Denotes a RoHS-compliant device that may include lead(Pb)
that is exempt under RoHS requirements. The lead finish is
JESD97 category e3, and is compatible with both lead-based
and lead-free soldering processes.
A "+" anywhere on the top mark denotes a lead(Pb)-free device.
A "#" denotes a RoHS-compliant device.
UL is a registered trademark of Underwriters Laboratories Inc.
19-5578; Rev 9; 4/15
DS1340 I2C RTC with Trickle Charger
Maxim Integrated | 2www.maximintegrated.com
Absolute Maximum Ratings
Recommended DC Operating Conditions
(VCC = VCC MIN to VCC MAX, TA= -40°C to +85°C, unless otherwise noted. Typical values are at VCC = 3.3V, TA= +25°C, unless
otherwise noted.) (Note 1)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Voltage Range on VCC or VBACKUP Pins
Relative to Ground.............................................-0.3V to +6.0V
Voltage Range on SDA, SCL, and FT/OUT
Relative to Ground..................................-0.3V to (VCC + 0.3V)
Operating Temperature Range ...........................-40°C to +85°C
Storage Temperature Range .............................-55°C to +125°C
Lead Temperature (soldering, 10s) .................................+260°C
Soldering Temperature (reflow) .......................................+260°C
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
DS1340-18 1.71 1.8 5.5
DS1340-3 2.7 3.0 5.5
Supply Voltage (Note 2) VCC
DS1340-33 2.97 3.3 5.5
V
Input Logic 1 (SDA, SCL) VIH (Note 2) 0.7 x VCC V
CC + 0.3 V
Input Logic 0 (SDA, SCL) VIL (Note 2) -0.3 +0.3 x VCC V
Supply Voltage, Pullup
(FT/OUT, SDA, SCL), VCC = 0V VPU (Note 2) 5.5 V
DS1340-18 1.3 3.7
DS1340-3 1.3 3.7
Backup Supply Voltage (Note 2) VBACKUP
DS1340-33 1.3 5.5
V
R1 (Notes 3, 4) 250
R2 (Note 5) 2000
Trickle-Charge Current-Limiting
Resistors
R3 (Note 6) 4000
DS1340-18 1.51 1.6 1.71
DS1340-3 2.45 2.6 2.7
Power-Fail Voltage (Note 2) VPF
DS1340-33 2.70 2.88 2.97
V
Input Leakage (SCL, CLK) ILI -1 +1 μA
I/O Leakage (SDA, FT/OUT) ILO -1 +1 μA
VCC > 2V; VOL = 0.4V 3.0
SDA Logic 0 Output IOLSDA 1.7V < VCC < 2V; VOL = 0.2 x VCC 3.0
mA
VCC > 2V; VOL = 0.4V 3.0
1.7V < VCC < 2V; VOL = 0.2 x VCC 3.0
mA
FT/OUT Logic 0 Output IOLSQW
1.3V < VCC < 1.7V; VOL = 0.2x VCC 250 μA
DS1340-18; VCC = 1.89V 72 150
DS1340-3; VCC = 3.3V 108 200
Active Supply Current (Note 7) ICCA
DS1340-33; VCC = 5.5V 192 300
μA
DS1340-18; VCC = 1.89V 60 100
DS1340-3; VCC = 3.3V 81 125
Standby Current (Note 8) ICCS
DS1340-33; VCC = 5.5V 100 150
μA
VBACKUP Leakage Current IBACKUPLKG V
BACKUP = 3.7V 100 nA
DS1340 I2C RTC with Trickle Charger
Maxim Integrated | 3www.maximintegrated.com
DC Electrical Characteristics
(VCC = 0V, VBACKUP = 3.7V, TA= -40°C to +85°C, unless otherwise noted.) (Note 1)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
IBACKUP1 OSC ON, FT = 0 (Note 9) 800 1150
IBACKUP2 OSC ON, FT = 1 (Note 9) 850 1250
VBACKUP Current
IBACKUP3 OSC ON, FT = 0, VBACKUP = 3.0V,
TA = +25°C (Notes 9, 10) 800 1000
nA
VBACKUP Data-Retention Current IBACKUPDR OSC OFF 25.0 100 nA
AC Electrical Characteristics
(VCC = VCC MIN to VCC MAX, TA= -40°C to +85°C, unless otherwise noted.) (Notes 1,14, Figure 1)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Standard mode 0 100
SCL Clock Frequency fSCL Fast mode 100 400 kHz
Standard mode 4.7
Bus Free Time Between STOP
and START Conditions tBUF Fast mode 1.3 μs
Standard mode 4.0
Hold Time (Repeated) START
Condition (Note 11) tHD:STA Fast mode 0.6 μs
Standard mode 4.7
Low Period of SCL Clock tLOW Fast mode 1.3 μs
Standard mode 4.0
High Period of SCL Clock tHIGH Fast mode 0.6 μs
Standard mode 0 0.9
Data Hold Time (Notes 12, 13) tHD:DAT Fast mode 0 0.9 μs
Standard mode 250
Data Setup Time (Note 14) tSU:DAT Fast mode 100 ns
Standard mode 4.7
START Setup Time tSU:STA Fast mode 0.6 μs
Standard mode 20 + 0.1CB 1000
Rise Time of SDA and SCL
Signals (Note 15) tRFast mode 20 + 0.1CB 300 ns
Standard mode 20 + 0.1CB 300
Fall Time of SDA and SCL
Signals (Note 15) tFFast mode 20 + 0.1CB 300 ns
Standard mode 4.7
Setup Time for STOP Condition tSU:STO Fast mode 0.6 μs
Capacitive Load for Each Bus
Line CB (Note 15) 400 pF
I/O Capacitance (SCL, SDA) CI/O 10 pF
Pulse Width of Spikes that Must
be Suppressed by the Input
Filter
tSP Fast mode 30 ns
Oscillator Stop Flag (OSF) Delay tOSF (Note 16) 100 ms
DS1340 I2C RTC with Trickle Charger
Maxim Integrated | 4www.maximintegrated.com
Power-Up/Power-Down Characteristics
(TA= -40°C to +85°C) (Figure 2)
PARAMETER SYMBOL CONDITIONSMIN TYP MAX UNITS
Recovery at Power-Up tREC (Note 17) 2 ms
VCC Fall Time; VPF(MAX) to
VPF(MIN) tVCCF 300 µs
VCC Rise Time; VPF(MIN) to
VPF(MAX) tVCCR s
WARNING: Under no circumstances are negative undershoots, of any amplitude, allowed when device is in battery-backup mode.
Note 1: Limits at -40°C are guaranteed by design and not production tested.
Note 2: All voltages are referenced to ground.
Note 3: Measured at VCC = typ, VBACKUP = 0V, register 08h = A5h.
Note 4: The use of the 250Ωtrickle-charge resistor is not allowed at VCC > 3.63V and should not be enabled.
Note 5: Measured at VCC = typ, VBACKUP = 0V, register 08h = A6h.
Note 6: Measured at VCC = typ, VBACKUP = 0V, register 08h = A7h.
Note 7: ICCA—SCL clocking at max frequency = 400kHz.
Note 8: Specified with I2C bus inactive.
Note 9: Measured with a 32.768kHz crystal attached to the X1 and X2 pins.
Note 10: Limits at +25°C are guaranteed by design and not production tested.
Note 11: After this period, the first clock pulse is generated.
Note 12: A device must internally provide a hold time of at least 300ns for the SDA signal (referred to as the VIH(MIN) of the SCL
signal) to bridge the undefined region of the falling edge of SCL.
Note 13: The maximum tHD:DAT only has to be met if the device does not stretch the low period (tLOW) of the SCL signal.
Note 14: A fast-mode device can be used in a standard-mode system, but the requirement tSU:DAT to 250ns must be met. This
is automatically the case if the device does not stretch the low period of the SCL signal. If such a device does stretch the
low period of the SCL signal, it must output the next data bit to the SDA line tR MAX + tSU:DAT = 1000 + 250 = 1250ns
before the SCL line is released.
Note 15: CB—total capacitance of one bus line in pF.
Note 16: The parameter tOSF is the period of time the oscillator must be stopped for the OSF flag to be set over the 0V VCC
VCCMAX and 1.3V VBAT 3.7V range.
Note 17: This delay applies only if the oscillator is enabled and running. If the oscillator is disabled or stopped, no power-up delay
occurs.
SCL
NOTE: TIMING IS REFERENCED TO VIL(MAX) AND VIH(MIN).
SDA
STOP START REPEATED
START
tBUF
tHD:STA
tHD:DAT tSU:DAT
tSU:STO
tHD:STA
tSP
tSU:STA
tHIGH
tR
tF
tLOW
Figure 1. Data Transfer on I2C Serial Bus
DS1340 I2C RTC with Trickle Charger
Maxim Integrated | 5www.maximintegrated.com
OUTPUTS
VCC
VPF(MAX)
INPUTS
HIGH-Z
DON'T CARE
VALID
RECOGNIZED RECOGNIZED
VALID
VPF(MIN)
tREC
tR
tF
VPF VPF
Figure 2. Power-Up/Power-Down Timing
ICCSA vs. VCC FT = 0
DS1340 toc01
VCC (V)
SUPPLY CURRENT (μA)
5.04.54.03.53.02.52.01.5
50
100
150
200
250
0
1.0 5.5
25
50
75
100
125
150
0
ICCS vs. VCC FT = 0
DS1340 toc02
VCC (V)
SUPPLY CURRENT (μA)
5.04.54.03.53.02.52.01.51.0 5.5
-1.8V
-3.0V
-3.3V
IBACKUP1 (FT = 0) vs. VBACKUP
DS1340 toc03
450
500
550
600
650
700
750
800
850
400
VBACKUP (V)
SUPPLY CURRENT (nA)
5.04.54.03.53.02.52.01.51.0 5.5
IBACKUP2 (FT = 1) vs. VBACKUP
DS1340 toc04
450
500
550
600
650
700
750
800
850
400
VBACKUP (V)
SUPPLY CURRENT (nA)
5.04.54.03.53.02.52.01.51.0 5.5
IBACKUP3 vs. TEMPERATURE
DS1340 toc05
TEMPERATURE (°C)
SUPPLY CURRENT (nA)
6040-20 0 20
500
550
600
650
700
750
800
850
-40 80
VBACKUP = 3.0V
OSCILLATOR FREQUENCY vs. SUPPLY VOLTAGE
(FT x 64)
DS1340 toc06
VBACKUP (V)
FREQUENCY (Hz)
5.04.54.03.53.02.52.01.5
32768.1
32768.2
32768.3
32768.4
32768.5
32768.6
32768.0
1.0 5.5
Typical Operating Characteristics
(VCC = +3.3V, TA= +25°C, unless otherwise noted.)
DS1340 I2C RTC with Trickle Charger
Maxim Integrated | 6www.maximintegrated.com
Detailed Description
The DS1340 is a low-power clock/calendar with a trickle
charger. Address and data are transferred serially
through a I2C bidirectional bus. The clock/calendar pro-
vides seconds, minutes, hours, day, date, month, and
year information. The date at the end of the month is
automatically adjusted for months with fewer than 31
days, including corrections for leap year. The DS1340
has a built-in power-sense circuit that detects power fail-
ures and automatically switches to the backup supply.
Power Control
The power-control function is provided by a precise,
temperature-compensated voltage reference and a
comparator circuit that monitors the VCC level. The
device is fully accessible and data can be written and
read when VCC is greater than VPF. However, when VCC
falls below VPF, the internal clock registers are blocked
from any access. If VPF is less than VBACKUP, the
device power is switched from VCC to VBACKUP when
VCC drops below VPF. If VPF is greater than VBACKUP,
the device power is switched from VCC to VBACKUP
Pin Description
PIN
816
NAME FUNCTION
1— X1
2— X2
Connections for a Standard 32.768kHz Quartz Crystal. The internal oscillator circuitry is designed for
operation with a crystal having a specified load capacitance (CL) of 12.5pF. X1 is the input to the oscillator
and can optionally be connected to an external 32.768kHz oscillator. The output of the internal oscillator,
X2, is left unconnected if an external oscillator is connected to X1.
314V
BACKUP
Connection for a Secondary Power Supply. For the 1.8V and 3V devices, VBACKUP must be held between
1.3V and 3.7V for proper operation. Diodes placed in series between the supply and the input pin may
result in improper operation. VBACKUP can be as high as 5.5V on the 3.3V device.
This pin can be connected to a primary cell such as a lithium coin cell. Additionally, this pin can be
connected to a rechargeable cell or a super cap when used with the trickle-charge feature. UL
recognized to ensure against reverse charging when used with a lithium battery
(www.maximintegrated.com/qa/info/ul).
4 15 GND Ground
5 16 SDA Serial Data Input/Output. SDA is the data input/output for the I2C serial interface. The SDA pin is open
drain and requires an external pullup resistor.
6 1 SCL Serial Clock Input. SCL is the clock input for the I2C interface and is used to synchronize data movement
on the serial interface.
7 2 FT/OUT
Frequency Test/Output. This pin is used to output either a 512Hz signal or the value of the OUT bit. When
the FT bit is logic 1, the FT/OUT pin toggles at a 512Hz rate. When the FT bit is logic 0, the FT/OUT pin
reflects the value of the OUT bit. This open-drain pin requires an external pullup resistor, and operates
with either VCC or VBACKUP applied. The pullup voltage can be up to 5.5V, regardless of the voltage on
VCC. If not used, this pin can be left unconnected.
83 V
CC
Primary Power Supply. When voltage is applied within normal limits, the device is fully accessible and data
can be written and read. When a backup supply is connected to the device and VCC is below VPF, reads
and writes are inhibited. However, the timekeeping function continues unaffected by the lower input voltage.
4–13 N.C. No Connection. Must be connected to ground.
SUPPLY CONDITION READ/WRITE
ACCESS
POWERED
BY
VCC < VPF,
VCC < VBACKUP No VBAT
VCC < VPF,
VCC > VBACKUP No VCC
VCC > VPF,
VCC < VBACKUP Yes VCC
VCC > VPF,
VCC > VBACKUP Yes VCC
Table 1. Power Control
DS1340 I2C RTC with Trickle Charger
Maxim Integrated | 7www.maximintegrated.com
when VCC drops below VBACKUP. The registers are
maintained from the VBACKUP source until VCC is
returned to nominal levels (Table 1). After VCC returns
above VPF, read and write access is allowed tREC.
Oscillator Circuit
The DS1340 uses an external 32.768kHz crystal. The
oscillator circuit does not require any external resistors
or capacitors to operate. Table 2 specifies several crys-
tal parameters for the external crystal. Figure 3 shows a
functional schematic of the oscillator circuit. If using a
crystal with the specified characteristics, the startup
time is usually less than one second.
Clock Accuracy
The initial clock accuracy depends on the accuracy of
the crystal and the accuracy of the match between the
capacitive load of the oscillator circuit and the capaci-
tive load for which the crystal was trimmed. Additional
error is added by crystal frequency drift caused by
temperature shifts. External circuit noise coupled into
the oscillator circuit can result in the clock running fast.
Figure 4 shows a typical PC board layout for isolating
the crystal and oscillator from noise. Refer to
Application Note 58: Crystal Considerations with Dallas
Real-Time Clocks
(www.maximintegrated.com/RTCapps)
for detailed information.
DS1340C Only
The DS1340C integrates a standard 32,768Hz crystal
into the package. Typical accuracy with nominal VCC
and +25°C is approximately +15ppm. Refer to
Application Note 58 for information about crystal accu-
racy vs. temperature.
Operation
The DS1340 operates as a slave device on the serial
bus. Access is obtained by implementing a START
condition and providing a device identification code fol-
lowed by data. Subsequent registers can be accessed
sequentially until a STOP condition is executed. The
device is fully accessible and data can be written and
read when VCC is greater than VPF. However, when
VCC falls below VPF, the internal clock registers are
blocked from any access. If VPF is less than VBACKUP,
the device power is switched from VCC to VBACKUP
when VCC drops below VPF. If VPF is greater than
VBACKUP, the device power is switched from VCC to
VBACKUP when VCC drops below VBACKUP. The regis-
ters are maintained from the VBACKUP source until VCC
is returned to nominal levels. The functional diagram
(Figure 5) shows the main elements of the serial RTC.
PARAMETER SYMBOL MIN TYP MAX UNITS
Nominal
Frequency fO32.768 kHz
Series Resistance ESR 80 kΩ
Load Capacitance CL12.5 pF
Table 2. Crystal Specifications*
*
The crystal, traces, and crystal input pins should be isolated
from RF generating signals. Refer to
Application Note 58:
Crystal Considerations for Dallas Real-Time Clocks
for addi-
tional specifications.
COUNTDOWN
CHAIN
RTC
X1 X2
CL1CL2
CRYSTAL
RTC
REGISTERS
Figure 3. Oscillator Circuit Showing Internal Bias Network
CRYSTAL
X1
X2
GND
LOCAL GROUND PLANE (LAYER 2)
Figure 4. Layout Example
DS1340 I2C RTC with Trickle Charger
Maxim Integrated | 8www.maximintegrated.com
Address Map
Table 3 shows the DS1340 address map. The RTC reg-
isters are located in address locations 00h to 06h, and
the control register is located at 07h. The trickle-charge
and flag registers are located in address locations 08h
to 09h. During a multibyte access of the timekeeping
registers, when the address pointer reaches 07h—the
end of the clock and control register space—it wraps
around to location 00h. Writing the address pointer to
the corresponding location accesses address locations
08h and 09h. After accessing location 09h, the address
pointer wraps around to location 00h. On a I2C START,
STOP, or address pointer incrementing to location 00h,
the current time is transferred to a second set of regis-
ters. The time information is read from these secondary
registers, while the clock may continue to run. This
eliminates the need to reread the registers in case the
main registers update during a read.
Clock and Calendar
The time and calendar information is obtained by read-
ing the appropriate register bytes. Table 3 shows the
RTC registers. The time and calendar data are set or
initialized by writing the appropriate register bytes. The
contents of the time and calendar registers are in the
binary-coded decimal (BCD) format. The day-of-week
ADDRESS BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 FUNCTION RANGE
00H EOSC 10 Seconds Seconds Seconds 00–59
01H X 10 Minutes Minutes Minutes 00–59
02H CEB CB 10 Hours Hours Century/Hours 0–1; 00–23
03H X X X X X Day Day 01–07
04H X X 10 Date Date Date 01–31
05H X X X 10 Month Month Month 01–12
06H 10 Year Year Year 00–99
07H OUT FT S CAL4 CAL3 CAL2 CAL1 CAL0 Control
08H TCS3 TCS2 TCS1 TCS0 DS1 DS0 ROUT1 ROUT0 Trickle Charger
09H OSF 0 0 0 0 0 0 0 Flag
Table 3. Address Map
X = Read/Write bit
Note: Unless otherwise specified, the state of the registers is not defined when power is first applied.
SERIAL
INTERFACE
AND ADDRESS
REGISTER
CONTROL
LOGIC
"C" VERSION ONLY
SCL
SDA
512Hz MUX/
BUFFER
FT/OUT
USER BUFFER
(7 BYTES)
CLOCK AND
CALENDAR
REGISTERS
32,768Hz
1Hz
X1
POWER
CONTROL
VCC
VBACKUP
DIVIDER AND
CALIBRATION
CIRCUIT
X2
CL
CLN
DS1340
Figure 5. Functional Diagram
DS1340 I2C RTC with Trickle Charger
Maxim Integrated | 9www.maximintegrated.com
register increments at midnight. Values that correspond
to the day of week are user-defined but must be
sequential (i.e., if 1 equals Sunday, then 2 equals
Monday, and so on). Illogical time and date entries
result in undefined operation. Bit 7 of register 0 is the
enable oscillator (EOSC) bit. When this bit is set to 1,
the oscillator is disabled. When cleared to 0, the oscil-
lator is enabled. The initial power-up value of EOSC is
0. The clock can be halted whenever the timekeeping
functions are not required, minimizing VBAT current
(IBACKUPDR) when VCC is not applied.
Location 02h is the century/hours register. Bit 7 and bit
6 of the century/hours register are the century-enable
bit (CEB) and the century bit (CB). Setting CEB to logic
1 causes the CB bit to toggle, either from a logic 0 to a
logic 1, or from a logic 1 to a logic 0, when the years
register rolls over from 99 to 00. If CEB is set to logic 0,
CB does not toggle.
When reading or writing the time and date registers,
secondary (user) buffers are used to prevent errors
when the internal registers update. When reading the
time and date registers, the user buffers are synchro-
nized to the internal registers on any START or STOP
and when the register pointer rolls over to zero. The
time information is read from these secondary registers
while the clock continues to run. This eliminates the
need to reread the registers in case the internal regis-
ters update during a read.
The divider chain is reset whenever the seconds regis-
ter is written. Write transfers occur on the acknowledge
from the DS1340. Once the divider chain is reset, to
avoid rollover issues, the remaining time and date reg-
isters must be written within one second.
On a power-on reset (POR), the time and date are set
to 00:00:00 01/01/00 (hh:mm:ss DD/MM/YY) and the
day register is set to 01.
Special-Purpose Registers
The DS1340 has three additional registers (control,
trickle charger, and flag) that control the RTC, trickle
charger, and oscillator flag output.
Control Register (07h)
Bit 7: Output Control (OUT). This bit controls the out-
put level of the FT/OUT pin when the FT bit is set to 0. If
FT = 0, the logic level on the FT/OUT pin is 1 if OUT = 1
and 0 if OUT = 0. The initial power-up OUT value is 1.
Bit 6: Frequency Test (FT). When this bit is 1, the
FT/OUT pin toggles at a 512Hz rate. When FT is written
to 0, the OUT bit controls the state of the FT/OUT pin.
The initial power-up value of FT is 0.
Bit 5: Calibration Sign Bit (S). A logic 1 in this bit indi-
cates positive calibration for the RTC. A 0 indicates
negative calibration for the clock. See the
Clock
Calibration
section for a detailed description of the bit
operation. The initial power-up value of S is 0.
Bits 4 to 0: Calibration Bits (CAL4 to CAL0). These
bits can be set to any value between 0 and 31 in binary
form. See the
Clock Calibration
section for a detailed
description of the bit operation. The initial power-up
value of CAL0–CAL4 is 0.
Trickle-Charger Register (08h)
The simplified schematic in Figure 6 shows the basic
components of the trickle charger. The trickle-charge
select (TCS) bits (bits 4–7) control the selection of the
trickle charger. To prevent accidental enabling, only a
BIT 7
TCS3
1 OF 16 SELECT
NOTE: ONLY 1010b
ENABLES CHARGER
1 OF 2
SELECT
VCC VBACKUP
R1
250Ω
TCS0-3 = TRICKLE-CHARGER SELECT
DS0-1 = DIODE SELECT
TOUT0-1 = RESISTOR SELECT
R2
2kΩ
R3
4kΩ
1 OF 3
SELECT
BIT 6
TCS2
BIT 5
TCS1
BIT 4
TCS0
BIT 3
DS1
BIT 2
DS0
BIT 1
ROUT1
BIT 0
ROUT0
Figure 6. Trickle Charger Functional Diagram
DS1340 I2C RTC with Trickle Charger
Maxim Integrated | 10www.maximintegrated.com
pattern on 1010 enables the trickle charger. All other
patterns disable the trickle charger. The trickle charger
is disabled when power is first applied. The diode-
select (DS) bits (bits 2, 3) select whether or not a diode
is connected between VCC and VBACKUP. If DS is 01,
no diode is selected; if DS is 10, a diode is selected.
The ROUT bits (bits 0, 1) select the value of the resistor
connected between VCC and VBACKUP. Table 3 shows
the resistor selected by the resistor select (ROUT) bits
and the diode selected by the diode select (DS) bits.
Warning: The ROUT value of 250Ωmust not be select-
ed whenever VCC is greater than 3.63V.
The user determines diode and resistor selection
according to the maximum current desired for battery
or super cap charging (Table 4). The maximum charg-
ing current can be calculated as illustrated in the fol-
lowing example.
Assume that a 3.3V system power supply is applied to
VCC and a super cap is connected to VBACKUP. Also
assume that the trickle charger has been enabled with
a diode and resistor R2 between VCC and VBACKUP.
The maximum current IMAX would therefore be calculat-
ed as follows:
IMAX = (3.3V - diode drop) / R2 (3.3V - 0.7V) /
2kΩ≈1.3mA
As the super cap charges, the voltage drop between
VCC and VBACKUP decreases and therefore the charge
current decreases.
Flag Register (09h)
Bit 7: Oscillator Stop Flag (OSF). A logic 1 in this bit
indicates that the oscillator has stopped or was
stopped for some time period and may be used to
judge the validity of the clock and calendar data. This
bit is edge triggered and is set to logic 1 when the
internal circuitry senses that the oscillator has transi-
tioned from a normal run state to a STOP condition. The
following are examples of conditions that can cause the
OSF bit to be set:
1) The first time power is applied.
2) The voltages present on VCC and VBACKUP
are insufficient to support oscillation.
3) The EOSC bit is set to 1, disabling the
oscillator.
4) External influences on the crystal (e.g., noise,
leakage).
The OSF bit remains at logic 1 until written to logic 0. It
can only be written to logic 0. Attempting to write OSF
to logic 1 leaves the value unchanged.
Bits 6 to 0: All other bits in the flag register read as 0
and cannot be written.
Clock Calibration
The DS1340 provides a digital clock calibration feature
to allow compensation for crystal and temperature vari-
ations. The calibration circuit adds or subtracts counts
from the oscillator divider chain at the divide-by-256
stage. The number of pulses blanked (subtracted for
negative calibration) or inserted (added for positive cal-
ibration) depends upon the value loaded into the five
calibration bits (CAL4–CAL0) located in the control reg-
ister. Adding counts speeds the clock up and subtract-
ing counts slows the clock down.
The calibration bits can be set to any value between 0
and 31 in binary form. Bit 5 of the control register, S, is
the sign bit. A value of 1 for the S bit indicates positive
calibration, while a value of 0 represents negative cali-
bration. Calibration occurs within a 64-minute cycle.
The first 62 minutes in the cycle can, once per minute,
TCS3TCS2TCS1TCS0DS1DS0 ROUT1 ROUT0 FUNCTION
X X X X 0 0 X X Disabled
X X X X 1 1 X X Disabled
XXXXXX00Disabled
1 0 1 0 0 1 0 1 No diode, 250Ω resistor
1 0 1 0 1 0 0 1 One diode, 250Ω resistor
1 0 1 0 0 1 1 0 No diode, 2kΩ resistor
1 0 1 0 1 0 1 0 One diode, 2kΩ resistor
1 0 1 0 0 1 1 1 No diode, 4kΩ resistor
1 0 1 0 1 0 1 1 One diode, 4kΩ resistor
0 0 0 0 0 0 0 0 Power-on reset value
Table 4. Trickle-Charge Register
DS1340 I2C RTC with Trickle Charger
Maxim Integrated | 11www.maximintegrated.com
have a one-second interval where the calibration is per-
formed. Negative calibration blanks 128 cycles of the
32,768Hz oscillator, slowing the clock down. Positive
calibration inserts 256 cycles of the 32,768Hz oscillator,
speeding the clock up. If a binary 1 is loaded into the
calibration bits, only the first two minutes in the 64-
minute cycle are modified. If a binary 6 is loaded, the
first 12 minutes are affected, and so on. Therefore,
each calibration step either adds 512 or subtracts 256
oscillator cycles for every 125,829,120 actual 32,678Hz
oscillator cycles (64 minutes). This equates to
+4.068ppm or -2.034ppm of adjustment per calibration
step. If the oscillator runs at exactly 32,768Hz, each of
the 31 increments of the calibration bits would repre-
sent +10.7 or -5.35 seconds per month, corresponding
to +5.5 or -2.75 minutes per month.
For example, if using the FT function, a reading of
512.01024Hz would indicate a +20ppm oscillator fre-
quency error, requiring a -10(00 1010) value to be
loaded in the S bit and the five calibration bits.
Note: Setting the calibration bits does not affect the fre-
quency test output frequency. Also note that writing to
the control register resets the divider chain.
I2C Serial Data Bus
The DS1340 supports a bidirectional I2C bus and data
transmission protocol. A device that sends data onto
the bus is defined as a transmitter and a device receiv-
ing data as a receiver. The device that controls the
message is called a master. The devices that are con-
trolled by the master are slaves. A master device that
generates the serial clock (SCL), controls the bus
access, and generates the START and STOP condi-
tions must control the bus. The DS1340 operates as a
slave on the I2C bus. Connections to the bus are made
through the open-drain I/O lines SDA and SCL. Within
the bus specifications a standard mode (100kHz max
clock rate) and a fast mode (400kHz max clock rate)
are defined. The DS1340 works in both modes.
The following bus protocol has been defined (Figure 7):
Data transfer can be initiated only when the bus is
not busy.
During data transfer, the data line must remain
stable whenever the clock line is high. Changes in
the data line while the clock line is high are inter-
preted as control signals.
Accordingly, the following bus conditions have been
defined:
Bus not busy: Both data and clock lines remain
high.
START data transfer: A change in the data line’s
state from high to low, while the clock line is high,
defines a START condition.
STOP data transfer: A change in the data line’s
state from low to high, while the clock line is high,
defines a STOP condition.
Data valid: The data line’s state represents valid
data when, after a START condition, the data line is
stable for the duration of the high period of the
clock signal. The data on the line must be changed
during the low period of the clock signal. There is
one clock pulse per bit of data.
Each data transfer is initiated with a START condi-
tion and terminated with a STOP condition. The
number of data bytes transferred between the
START and STOP conditions is not limited, and is
SDA
SCL
IDLE
1–7 8 9 1–7 8 9 1–7 8 9
START
CONDITION STOP CONDITION
REPEATED START
SLAVE
ADDRESS
R/W ACK ACKDATA ACK/
NACK
DATA
MSB FIRST MSB LSB MSB LSB
REPEATED IF MORE BYTES
ARE TRANSFERRED
Figure 7. I2C Data Transfer Overview
DS1340 I2C RTC with Trickle Charger
Maxim Integrated | 12www.maximintegrated.com
determined by the master device. The information
is transferred byte-wise and each receiver
acknowledges with a ninth bit.
Acknowledge: Each receiving device, when
addressed, is obliged to generate an acknowl-
edge after the reception of each byte. The master
device must generate an extra clock pulse that is
associated with this acknowledge bit.
A device that acknowledges must pull down the
SDA line during the acknowledge clock pulse in
such a way that the SDA line is stable low during
the high period of the acknowledge-related clock
pulse. Setup and hold times must be taken into
account. A master must signal an end of data to
the slave by not generating an acknowledge bit on
the last byte that has been clocked out of the
slave. In this case, the slave must leave the data
line high to enable the master to generate the
STOP condition.
Figures 8 and 9 detail how data transfer is accom-
plished on the I2C bus. Depending upon the state of
the R/Wbit, two types of data transfer are possible:
Data transfer from a master transmitter to a
slave receiver. The first byte transmitted by the
master is the slave address. Next follows a num-
ber of data bytes. The slave returns an acknowl-
edge bit after each received byte.
Data transfer from a slave transmitter to a mas-
ter receiver. The master transmits the first byte (the
slave address). The slave then returns an acknowl-
edge bit. Next follows a number of data bytes trans-
mitted by the slave to the master. The master
returns an acknowledge bit after all received bytes
other than the last byte. At the end of the last
received byte, a not acknowledge is returned.
The master device generates all the serial clock
pulses and the START and STOP conditions. A
transfer is ended with a STOP condition or with a
repeated START condition. Since a repeated
START condition is also the beginning of the next
serial transfer, the bus is not released.
The DS1340 can operate in the following two modes:
Slave Receiver Mode (Write Mode): Serial data
and clock are received through SDA and SCL.
After each byte is received, an acknowledge bit is
transmitted. Start and STOP conditions are recog-
nized as the beginning and end of a serial trans-
fer. Hardware performs address recognition after
reception of the slave address and direction bit.
The slave address byte is the first byte received
after the master generates the START condition.
The slave address byte contains the 7-bit DS1340
address, which is 1101000, followed by the direc-
tion bit (R/W), which is 0 for a write. After receiving
and decoding the slave address byte, the DS1340
outputs an acknowledge on SDA. After the
DS1340 acknowledges the slave address + write
bit, the master transmits a word address to the
DS1340. This sets the register pointer on the
DS1340, with the DS1340 acknowledging the
transfer. The master can then transmit zero or
more bytes of data, with the DS1340 acknowledg-
ing each byte received. The register pointer incre-
ments after each data byte is transferred. The
master generates a STOP condition to terminate
the data write.
Slave Transmitter Mode (Read Mode): The first
byte is received and handled as in the slave
receiver mode. However, in this mode, the direc-
tion bit indicates that the transfer direction is
reversed. The DS1340 transmits serial data on
SDA while the serial clock is input on SCL. Start
and STOP conditions are recognized as the begin-
ning and end of a serial transfer. Hardware per-
forms address recognition after reception of the
slave address and direction bit. The slave address
byte is the first byte received after the master gen-
erates the START condition. The slave address
byte contains the 7-bit DS1340 address, which is
1101000, followed by the direction bit (R/W),
which is 1 for a read. After receiving and decoding
the slave address byte, the DS1340 outputs an
acknowledge on SDA. The DS1340 then begins to
transmit data starting with the register address
pointed to by the register pointer. If the register
pointer is not written to before the initiation of a
read mode, the first address that is read is the last
one stored in the register pointer. The DS1340
must receive a not acknowledge to end a read.
DS1340 I2C RTC with Trickle Charger
Maxim Integrated | 13www.maximintegrated.com
MASTER TO SLAVE SLAVE TO MASTER
...
AXXXXXXXXA1101000S 0 XXXXXXXX A XXXXXXXX A XXXXXXXX A P
<DATA (n + X)
S - START
A - ACKNOWLEDGE (ACK)
P - STOP
R/W - READ/WRITE OR DIRECTION BIT ADDRESS
DATA TRANSFERRED
(X + 1 BYTES + ACKNOWLEDGE)
<SLAVE
ADDRESS> <R/W> <WORD ADDRESS (n)> <DATA (n)> <DATA (n + 1)>
Figure 8. Data Write—Slave Receiver Mode
...
AXXXXXXXXA1101000S 1 XXXXXXXX A XXXXXXXX A XXXXXXXX A P
S - START
A - ACKNOWLEDGE (ACK)
P - STOP
A - NOT ACKNOWLEDGE (NACK)
R/W - READ/WRITE OR DIRECTION BIT ADDRESS
DATA TRANSFERRED
(X + 1 BYTES + ACKNOWLEDGE)
NOTE: LAST DATA BYTE IS FOLLOWED BY A NACK.
MASTER TO SLAVE SLAVE TO MASTER
<DATA (n + X)>
<SLAVE
ADDRESS> <R/W> <DATA (n)> <DATA (n + 1)> <DATA (n + 2)>
Figure 9. Data Read—Slave Transmitter Mode
S - START
Sr - REPEATED START
A - ACKNOWLEDGE (ACK)
P - STOP
A - NOT ACKNOWLEDGE (NACK)
R/W - READ/WRITE OR DIRECTION BIT ADDRESS
<R/W><R/W> <WORD ADDRESS (n)>
<SLAVE
ADDRESS>
<SLAVE
ADDRESS>
AXXXXXXXXA1101000 1101000S Sr0 A1
DATA TRANSFERRED
(X + 1 BYTES + ACKNOWLEDGE)
NOTE: LAST DATA BYTE IS FOLLOWED BY A NACK.
MASTER TO SLAVE SLAVE TO MASTER
AXXXXXXXX XXXXXXXX A XXXXXXXX A XXXXXXXX A P
<DATA (n)> <DATA (n + 1)> <DATA (n + 2)> <DATA (n + X)>
...
Figure 10. Data Write/Read (Write Pointer, Then Read)—Slave Receive and Transmit
DS1340 I2C RTC with Trickle Charger
Maxim Integrated | 14www.maximintegrated.com
Chip Information
PROCESS: CMOS
SUBSTRATE CONNECTED TO GROUND
Thermal Information
Theta-JA: 170°C/W (0.150in SO)
Theta-JC: 40°C/W (0.150in SO)
Theta-JA: 221°C/W (µSOP)
Theta-JC: 39°C/W (µSOP)
Theta-JA: 89.6°C/W (0.300in SO)
Theta-JC: 24.8°C/W (0.300in SO)
Handling, PC Board Layout,
and Assembly
The DS1340C package contains a quartz tuning-fork
crystal. Pick-and-place equipment may be used, but
precautions should be taken to ensure that excessive
shocks are avoided. Exposure to reflow is limited to 2
times maximum. Ultrasonic cleaning should be avoided
to prevent damage to the crystal.
Avoid running signal traces under the package, unless
a ground plane is placed between the package and the
signal line. All N.C. (no connect) pins must be connect-
ed to ground.
Moisture-sensitive packages are shipped from the facto-
ry dry-packed.Handling instructions listed on the pack-
age label must be followed to prevent damage during
reflow. Refer to the IPC/JEDEC J-STD-020 standard for
moisture-sensitive device (MSD) classifications.
1
2
3
4
8
7
6
5
VCC
FT/OUT
SCL
SDA
VBACKUP
GND
X2
X1
TOP VIEW
SO, µSOP
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
SCL SDA
GND
VBACKUP
N.C.
N.C.
N.C.
N.C.
N.C.
SO (300 mils)
FT/OUT
VCC
N.C.
N.C.
N.C.
N.C.
N.C.
DS1340
DS1340C
Pin Configurations
Package Information
For the latest package outline information and land patterns (foot-
prints), go to www.maximintegrated.com/packages. Note that a
“+”, “#”, or “-” in the package code indicates RoHS status only.
Package drawings may show a different suffix character, but the
drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
8-pin SO (150
S8+2
21-0041
8-pin µSOP
U8+1
21-0036
16-pin SO (300
W16#H2
21-0042
DS1340 I2C RTC with Trickle Charger
Maxim Integrated | 15www.maximintegrated.com
Revision History
REVISION
NUMBER
REVISION
DATE DESCRIPTION PAGES
CHANGED
0 6/03
Initial release.
Changed “2-wire” to “I2C” throughout the data sheet. All
Added UL recognition info bullet to the Features section and to the VBACKUP pin
description. 1, 6
Added the “I/O Capacitance (SCL, SDA)” parameter (CI/O) to the AC Electrical
Characteristics table. 2
1 7/04
Added “SDA, SCL and “VCC = 0V” to the “Supply Voltage, Pullup (FT/OUT)” parameter
and changed the symbol from “VIH” to “VPU” in the Recommended DC Operating
Conditions table; in the DC Electrical Characteristics table, changed theOscillator
Current parameter to VBACKUP Current.
3
Added the integrated-crystal and lead-free packages to the Ordering Information table;
added the integrated-crystal packages to the Features,Pin Configurations,Pin
Description.
1, 6
In Table 1, added increased crystal ESR with increased supply minimum voltage
requirement. 6
Added the DS1340C Only section. 7
Updated Figure 5 to also show the “C Version crystal. 7
Added the Handling, PC Board Layout, and Assembly section. 12
2 12/04
Added the integrated-crystal package Theta-JA and Theta-JC information to the
Thermal Information section. 13
3 11/05 Updated the Ordering Information table to correct lead-free/RoHS packages. 1
In the General Description section, indicated that the time and date function continues
while powered by VBACKUP.1
Updated the Typical Operating Circuit by removing pin numbers and adding a bypass
capacitor. 1
In the Pin Description, updated the VBACKUP description to indicate that no diodes
should be placed between the battery and pin and added the UL link; changed the
VCC description.
6
Added the Power Control section and new Table 1. 6
In the Handling, PC Board Layout, and Assembly section, added solder reflow
information for the RoHS SO package. 13
4 3/06
Added Package Information table. 14
Removed leaded part numbers from the Ordering Information table. 1
Removed the tRPU parameter and RST waveform from Figure 2. Replaced tRST with tREC.5
In the Typical Operating Characteristics section, updated/changed the “FT vs.
VBACKUPgraph to “OSCILLATOR FREQUENCY vs. SUPPLY VOLTAGE (FT x 64).” 5
In the Pin Description, added pullup voltage information to the SDA, SCL, and FT/OUT
descriptions. 6
Updated Figure 5. 8
In the Clock and Calendar section, added text explaining the use of EOSC to halt the
oscillator. 9
5 8/08
Replaced Figure 7 with an updated version; changed Figures 8 and 9 and added
Figure 10 with more comprehensive I2C figures. 13
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent
licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and
max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. © 2015 Maxim Integrated Products, Inc. | 16
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com.
DS1340 I2C RTC with Trickle Charger
Revision History (continued)
REVISION
NUMBER
REVISION
DATE DESCRIPTION PAGES
CHANGED
Updated the top mark information in the Ordering Information table. 1
Updated the soldering information in the Absolute Maximum Ratings section. 2
Updated the SDA and SCL pin descriptions in the Pin Description table. 6
Increased ESR from 45,60k(max) to 80k(max) in Table 2. 7
6 10/10
Updated the Package Information table. 14
7 8/11
Raised VCC(MAX) limits for the -18 and -3 versions from 1.89V and 3.3V to 5.5V to
provide wide voltage functional operation; reorganized the EC tables and notes 2, 3
8 4/13
Clarified VBACKUP in Absolute Maximum Ratings and updated Clock Calibration
section 2, 9
9 4/15 Revised Benefits and Features section 1
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Maxim Integrated:
DS1340C-18# DS1340C-3# DS1340C-33# DS1340C-33#T&R DS1340U-18+ DS1340U-3+ DS1340U-3+T&R
DS1340U-33+T&R DS1340Z-18+ DS1340Z-3+ DS1340Z-3+T&R DS1340Z-33+T&R DS1340U-33+ DS1340Z-33+