DS90LV019
DS90LV019 3.3V or 5V LVDS Driver/Receiver
Literature Number: SNLS008B
DS90LV019
3.3V or 5V LVDS Driver/Receiver
General Description
The DS90LV019 is a Driver/Receiver designed specifically
for the high speed low power point-to-point interconnect ap-
plications. The device operates from a single 3.3V or 5.0V
power supply and includes one differential line driver and
one receiver. The DS90LV019 features an independent
driver and receiver with TTL/CMOS compatibility (D
IN
and
R
OUT
). The logic interface provides maximum flexibility as 4
separate lines are provided (D
IN
, DE, RE, and R
OUT
). The
device also features a flow-through pin out which allows
easy PCB routing for short stubs between its pins and the
connector. The driver has 3.5 mA output loop current.
The driver translates between TTL levels (single-ended) to
Low Voltage Differential Signaling levels. This allows for high
speed operation, while consuming minimal power with re-
duced EMI. In addition, the differential signaling provides
common-mode noise rejection.
The receiver threshold is ±100 mV over a ±1V common-
mode range and translates the low swing differential levels
to standard (TTL/CMOS) levels.
Features
nLVDS Signaling
n3.3V or 5.0V operation
nLow power CMOS design
nBalanced Output Impedance
nGlitch free power up/down (Driver disabled)
nHigh Signaling Rate Capacity (above 100 Mbps)
nUltra Low Power Dissipation
n±1V Common-Mode Range
n±100 mV Receiver Sensitivity
nProduct offered in SOIC and TSSOP packages
nFlow-Through Pin Out
nIndustrial Temperature Range Operation
Connection Diagram
Block Diagram
TRI-STATE®is a registered trademark of National Semiconductor Corporation.
DS100053-1
Order Number DS90LV019TM or DS90LV019TMTC
See NS Package Number M14A or MTC14
DS100053-2
August 2000
DS90LV019 3.3V or 5V LVDS Driver/Receiver
© 2000 National Semiconductor Corporation DS100053 www.national.com
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage V
CC
6.0V
Enable Input Voltage (DE, RE) −0.3V to (V
CC
+0.3V)
Driver Input Voltage (D
IN
) −0.3V to (V
CC
+ 0.3V)
Receiver Output Voltage
(R
OUT
) −0.3V to (V
CC
+ 0.3V)
Driver Output Voltage (DO±) −0.3V to +3.9V
Receiver Input Voltage (RI±) −0.3V to (V
CC
+ 0.3V)
Driver Short Circuit Current Continuous
ESD (Note 4)
(HBM, 1.5 kΩ, 100 pF) >2.0 kV
(EIAJ, 0 Ω, 200 pF) >200 V
Maximum Package Power Dissipation at 25˚C
SOIC 960 mW
Derate SOIC Package 7.7mW/˚C
TSSOP 790 mW
Derate TSSOP Package 6.3mW/˚C
Storage Temperature Range −65˚C to +150˚C
Lead Temperature
(Soldering, 4 sec.) 260˚C
Recommended Operating
Conditions
Min Max Units
Supply Voltage (V
CC
) or 3.0 3.6 V
Supply Voltage (V
CC
) 4.5 5.5 V
Receiver Input Voltage 0.0 2.4 V
Operating Free Air
Temperature T
A
−40 +85 ˚C
DC Electrical Characteristics
T
A
= −40˚C to +85˚C unless otherwise noted, V
CC
= 3.3 ±0.3V. (Notes 2, 3)
Symbol Parameter Conditions Pin Min Typ Max Units
DIFFERENTIAL DRIVER CHARACTERISTICS
V
OD
Output Differential Voltage R
L
= 100Ω(
Figure 1
) DO+,
DO− 250 350 450 mV
∆V
OD
V
OD
Magnitude Change 660mV
V
OS
Offset Voltage 1 1.25 1.7 V
∆V
OS
Offset Magnitude Change 5 60 mV
I
OZD
TRI-STATE®Leakage V
OUT
=V
CC
or GND, DE = 0V −10 ±1 +10 µA
I
OXD
Power-Off Leakage V
OUT
= 3.6V or GND, V
CC
= 0V −10 ±1 +10 µA
I
OSD
Output Short Circuit Current V
OUT
= 0V, DE = V
CC
−10 −6 −4 mA
DIFFERENTIAL RECEIVER CHARACTERISTICS
V
OH
Voltage Output High VID = +100 mV I
OH
= −400 µA R
OUT
2.9 3.3 V
Inputs Open 2.9 3.3 V
V
OL
Voltage Output Low I
OL
= 2.0 mA, VID = −100 mV 0.1 0.4 V
I
OS
Output Short Circuit Current V
OUT
= 0V −75 −34 −20 mA
V
TH
Input Threshold High RI+,
RI− +100 mV
V
TH
Input Threshold Low −100 mV
I
IN
Input Current V
IN
= +2.4V or 0V, V
CC
= 3.6V or
0V −10 ±1 +10 µA
DEVICE CHARACTERISTICS
V
IH
Minimum Input High Voltage D
IN
,
DE, RE 2.0 V
CC
V
V
IL
Maximum Input Low Voltage GND 0.8 V
I
IH
Input High Current V
IN
=V
CC
or 2.4V ±1±10 µA
I
IL
Input Low Current V
IN
= GND or 0.4V ±1±10 µA
V
CL
Input Diode Clamp Voltage I
CLAMP
= −18 mA −1.5 −0.7 V
I
CCD
Power Supply Current DE = RE = V
CC
V
CC
9 12.5 mA
I
CCR
DE=RE=0V 4.5 7.0 mA
I
CCZ
DE = 0V, RE = V
CC
3.7 7.0 mA
I
CC
DE=V
CC
,RE=0V 15 20 mA
C
D output
Capacitance DO+,
DO− 5pF
C
R input
Capacitance RI+,
RI− 5pF
DS90LV019
www.national.com 2
DC Electrical Characteristics
T
A
= −40˚C to +85˚C unless otherwise noted, V
CC
= 5.0 ±0.5V. (Notes 2, 3)
Symbol Parameter Conditions Pin Min Typ Max Units
DIFFERENTIAL DRIVER CHARACTERISTICS
V
OD
Output Differential Voltage R
L
= 100Ω(
Figure 1
) DO+,
DO− 250 360 450 mV
∆V
OD
V
OD
Magnitude Change 660mV
V
OS
Offset Voltage 1 1.25 1.8 V
∆V
OS
Offset Magnitude Change 5 60 mV
I
OZD
TRI-STATE Leakage V
OUT
=V
CC
or GND, DE = 0V −10 ±1 +10 µA
I
OXD
Power-Off Leakage V
OUT
= 5.5V or GND, V
CC
= 0V −10 ±1 +10 µA
I
OSD
Output Short Circuit Current V
OUT
= 0V, DE = V
CC
−10 −6 −4 mA
DIFFERENTIAL RECEIVER CHARACTERISTICS
V
OH
Voltage High VID = +100 mV I
OH
= −400 µA R
OUT
4.3 5.0 V
Inputs Open 4.3 5.0 V
V
OL
Voltage Output Low I
OL
= 2.0 mA, VID = −100 mV 0.1 0.4 V
I
OS
Output Short Circuit Current V
OUT
= 0V −150 −75 −40 mA
V
TH
Input Threshold High RI+,
RI− +100 mV
V
TH
Input Threshold Low −100 mV
I
IN
Input Current V
IN
= +2.4V or 0V, V
CC
= 5.5V or
0V −15 ±1 +15 µA
DEVICE CHARACTERISTICS
V
IH
Minimum Input High Voltage D
IN
,
DE ,RE 2.0 V
CC
V
V
IL
Maximum Input Low Voltage GND 0.8 V
I
IH
Input High Current V
IN
=V
CC
or 2.4 V ±1±10 µA
I
IL
Input Low Current V
IN
= GND or 0.4V ±1±10 µA
V
CL
Input Diode Clamp Voltage I
CLAMP
= −18 mA −1.5 −0.8 V
I
CCD
Power Supply Current DE = RE = V
CC
V
CC
12 19 mA
I
CCR
DE=RE=0V 5.8 8 mA
I
CCZ
DE = 0V, RE = V
CC
4.5 8.5 mA
I
CC
DE=V
CC
,RE=0V 18 48 mA
C
D output
Capacitance DO+,
DO− 5pF
C
R input
Capacitance RI+,
RI− 5pF
Note 1: “Absolute Maximum Ratings” are these beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device should
be operated at these limits. The table of “Electrical Characteristics” provides conditions for actual device operation.
Note 2: All currents into device pins are positive; all currents out of device pins are negative.All voltages are referenced to device ground unless otherwise specified.
Note 3: All typicals are given for VCC = +3.3V or +5.0V and TA= +25˚C, unless otherwise stated.
Note 4: ESD Rating:
HBM (1.5 kΩ, 100 pF) >2.0 kV
EIAJ (0Ω, 200 pF) >200V.
Note 5: CLincludes probe and fixture capacitance.
Note 6: Generator waveforms for all tests unless otherwise specified;f=1MHz, ZO=50Ω,t
r=t
f≤6.0 ns (0%–100%).
AC Electrical Characteristics
T
A
= −40˚C to +85˚C, V
CC
= 3.3V ±0.3V. (Note 6)
Symbol Parameter Conditions Min Typ Max Units
DRIVER TIMING REQUIREMENTS
t
PHLD
Differential Propagation Delay High to Low R
L
= 100Ω,
C
L
=10pF
(
Figure 2
and
Figure 3
)
2.0 4.0 6.5 ns
t
PLHD
Differential Propagation Delay Low to High 1.0 5.6 7.0 ns
t
SKD
Differential Skew |t
PHLD
−t
PLHD
| 0.4 1.0 ns
t
TLH
Transition Time Low to High 0.2 0.7 3.0 ns
t
THL
Transition Time High to Low 0.2 0.8 3.0 ns
DS90LV019
www.national.com3
AC Electrical Characteristics (Continued)
T
A
= −40˚C to +85˚C, V
CC
= 3.3V ±0.3V. (Note 6)
Symbol Parameter Conditions Min Typ Max Units
DRIVER TIMING REQUIREMENTS
t
PHZ
Disable Time High to Z R
L
= 100Ω,
C
L
=10pF
(
Figure 4
and
Figure 5
)
1.5 4.0 8.0 ns
t
PLZ
Disable Time Low to Z 2.5 5.3 9.0 ns
t
PZH
Enable Time Z to High 4.0 6.0 8.0 ns
t
PZL
Enable Time Z to Low 3.5 6.0 8.0 ns
RECEIVER TIMING REQUIREMENTS
t
PHLD
Differential Propagation Delay High to Low C
L
=10pF,
VID = 200 mV
(
Figure 6
and
Figure 7
)
3.0 5.8 7.0 ns
t
PLHD
Differential Propagation Delay Low to High 3.0 5.6 9.0 ns
t
SKD
Differential Skew |t
PHLD
−t
PLHD
| 0.55 1.5 ns
t
r
Rise Time 0.15 2.0 3.0 ns
t
f
Fall Time 0.15 0.9 3.0 ns
t
PHZ
Disable Time High to Z R
L
= 500Ω,
C
L
=10pF
(
Figure 8
and
Figure 9
)
3.0 4.0 6.0 ns
t
PLZ
Disable Time Low to Z 3.0 4.5 6.0 ns
t
PZH
Enable Time Z to High 3.0 6.0 8.0 ns
t
PZL
Enable Time Z to Low 3.0 6.0 8.0 ns
AC Electrical Characteristics
T
A
= −40˚C to +85˚C, V
CC
= 5.0V ±0.5V. (Note 6)
Symbol Parameter Conditions Min Typ Max Units
DRIVER TIMING REQUIREMENTS
t
PHLD
Differential Propagation Delay High to Low R
L
= 100Ω,
C
L
=10pF
(
Figure 2
and
Figure 3
)
2.0 3.3 6.0 ns
t
PLHD
Differential Propagation Delay Low to High 1.0 3.3 5.0 ns
t
SKD
Differential Skew |t
PHLD
−t
PLHD
| 0.6 1.0 ns
t
TLH
Transition Time Low to High 0.15 0.9 3.0 ns
t
THL
Transition Time High to Low 0.15 1.2 3.0 ns
t
PHZ
Disable Time High to Z R
L
= 100Ω,
C
L
=10pF
(
Figure 4
and
Figure 5
)
1.5 3.5 7.0 ns
t
PLZ
Disable Time Low to Z 3.0 5.2 9.0 ns
t
PZH
Enable Time Z to High 2.0 4.5 7.0 ns
t
PZL
Enable Time Z to Low 2.0 4.5 7.0 ns
RECEIVER TIMING REQUIREMENTS
t
PHLD
Differential Propagation Delay High to Low C
L
=10pF,
VID = 200 mV
(
Figure 6
and
Figure 7
)
3.0 6.0 8.0 ns
t
PLHD
Differential Propagation Delay Low to High 3.0 5.6 8.0 ns
t
SKD
Differential Skew |t
PHLD
−t
PLHD
| 0.7 1.6 ns
t
r
Rise Time 0.15 0.8 3.0 ns
t
f
Fall Time 0.15 0.8 3.0 ns
t
PHZ
Disable Time High to Z R
L
= 500Ω,
C
L
=10pF
(
Figure 8
and
Figure 9
)
3.0 3.5 4.5 ns
t
PLZ
Disable Time Low to Z 3.5 3.6 7.0 ns
t
PZH
Enable Time Z to High 3.0 5.0 7.0 ns
t
PZL
Enable Time Z to Low 3.0 5.0 7.0 ns
DS90LV019
www.national.com 4
Test Circuits and Timing Waveforms
DS100053-3
FIGURE 1. Differential Driver DC Test Circuit
DS100053-4
FIGURE 2. Differential Driver Propagation Delay and Transition Test Circuit
DS100053-5
FIGURE 3. Differential Driver Propagation and Transition Time Waveforms
DS100053-6
FIGURE 4. Driver TRI-STATE Delay Test Circuit
DS90LV019
www.national.com5
Test Circuits and Timing Waveforms (Continued)
DS100053-7
FIGURE 5. Driver TRI-STATE Delay Waveforms
DS100053-8
FIGURE 6. Receiver Propagation Delay and Transition Time Test Circuit
DS100053-9
FIGURE 7. Receiver Propagation Delay and Transition Time Waveforms
DS100053-10
FIGURE 8. Receiver TRI-STATE Delay Test Circuit
DS90LV019
www.national.com 6
Test Circuits and Timing Waveforms (Continued)
Typical Application Diagram
Applications Information
The DS90LV019 has two control pins, which allows the de-
vice to operate as a driver, a receiver or both driver and a re-
ceiver at the same time. There are a few common practices
which should be implied when designing PCB for LVDS sig-
naling. Recommended practices are:
•Use at least 4 PCB board layer (LVDS signals, ground,
power and TTL signals).
•Keep drivers and receivers as close to the (LVDS port
side) connector as possible.
•Bypass each LVDS device and also use distributed bulk
capacitance. Surface mount capacitors placed close to
power and ground pins work best. Two or three multi-
layer ceramic (MLC) surface mount capacitors 0.1 µF,
and 0.01 µF in parallel should be used between each V
CC
and ground. The capacitors should be as close as pos-
sible to the V
CC
pin.
•Use controlled impedance traces which match the differ-
ential impedance of your transmission medium (i.e.,
Cable) and termination resistor.
•Use the termination resistor which best matches the dif-
ferential impedance of your transmission line.
•Isolate TTL signals from LVDS signals.
MEDIA (CABLE AND CONNECTOR) SELECTION:
•Use controlled impedance media. The cables and con-
nectors should have a matched differential impedance of
about 100Ω.
DS100053-11
FIGURE 9. Receiver TRI-STATE Delay Waveforms TRI-STATE Delay Waveforms
DS100053-13
FIGURE 10. Terminated Input Fail-Safe Circuit
DS100053-12
DS90LV019
www.national.com7
Applications Information (Continued)
•Balanced cables (e.g., twisted pair) are usually better
than unbalanced cables (ribbon cable, simple coax) for
noise reduction and signal quality.
•For cable distances <0.5m, most cables can be made to
work effectively. For distances 0.5m ≤d≤10m, CAT 3
(category 3) twisted pair cable works well and is readily
available and relatively inexpensive. For distances
>10m, and high data rates CAT 5 twisted pair is recom-
mended.
•There are three Fail-Safe scenarios, open input pins,
shorted inputs pins and terminated input pins. The first
case is guaranteed for DS90LV019. A HIGH state on
R
OUT
pin can be achieved by using two external resistors
(one to V
CC
and one to GND) per
Figure 10
(Terminated
Input Fail-Safe Circuit). R1 and R2 should be R
T
to limit
the loading to the LVDS driver . R
T
is selected to match
the impedance of the cable.
TABLE 1. Functional Table
MODE SELECTED DE RE
DRIVER MODE H H
RECEIVER MODE L L
TRI-STATE MODE L H
FULL DUPLEX MODE H L
TABLE 2. Transmitter Mode
INPUTS OUTPUTS
DE DI DO+ DO−
HL L H
HH H L
H2
>
&
>
0.8 X X
LX Z Z
X = High or Low logic state
Z = High impedance state
L = Low state
H = High state
TABLE 3. Receiver Mode
INPUTS OUTPUT
RE (RI+) − (RI−)
LL(
<
−100 mV) L
LH(
>
+100 mV) H
L 100 mV >&>−100 mV X
HXZ
X = High or Low logic state
Z = High impedance state
L = Low state
H = High state
TABLE 4. Device Pin Description
Pin Name Pin # Input/Output Description
D
IN
2 I TTL Driver Input
DO±11, 12 O LVDS Driver Outputs
RI±9, 10 I LVDS Receiver Inputs
R
OUT
4 O TTL Receiver Output
RE 8 I Receiver Enable TTL Input (Active Low)
DE 1 I Driver Enable TTL Input (Active High)
GND 7 NA Ground
V
CC
14 NA Power Supply (3.3V ±0.3V or 5.0V ±0.5V)
DS90LV019
www.national.com 8
Physical Dimensions inches (millimeters) unless otherwise noted
Order Number DS90LV019TM
NS Package Number M14A
DS90LV019
www.national.com9
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: support@nsc.com
National Semiconductor
Europe Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: ap.support@nsc.com
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
www.national.com
Order Number DS90LV019TMTC
NS Package Number MTC14
DS90LV019 3.3V or 5V LVDS Driver/Receiver
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright ©2011, Texas Instruments Incorporated