PIC16F870/871 28/40-Pin 8-Bit CMOS FLASH Microcontrollers Devices Included in this Data Sheet: * PIC16F871 PDIP Microcontroller Core Features: * High-performance RISC CPU * Only 35 single word instructions to learn * All single cycle instructions except for program branches which are two cycle * Operating speed: DC - 20 MHz clock input DC - 200 ns instruction cycle * 2K x 14 words of FLASH Program Memory 128 x 8 bytes of Data Memory (RAM) 64 x 8 bytes of EEPROM Data Memory * Pinout compatible to the PIC16CXXX 28 and 40pin devices * Interrupt capability (up to 11 sources) * Eight level deep hardware stack * Direct, indirect and relative addressing modes * Power-on Reset (POR) * Power-up Timer (PWRT) and Oscillator Start-up Timer (OST) * Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operation * Programmable code-protection * Power saving SLEEP mode * Selectable oscillator options * Low-power, high-speed CMOS FLASH/EEPROM technology * Fully static design * In-Circuit Serial Programming (ICSP) via two pins * Single 5V In-Circuit Serial Programming capability * In-Circuit Debugging via two pins * Processor read/write access to program memory * Wide operating voltage range: 2.0V to 5.5V * High Sink/Source Current: 25 mA * Commercial and Industrial temperature ranges * Low-power consumption: - < 1.6 mA typical @ 5V, 4 MHz - 20 A typical @ 3V, 32 kHz - < 1 A typical standby current 1999 Microchip Technology Inc. MCLR/VPP/THV RA0/AN0 1 40 2 3 39 38 4 37 RA3/AN3/VREF+ 5 36 RA4/T0CKI 6 7 35 34 RB2 33 RB0/INT VDD RA1/AN1 RA2/AN2/VREF- RA5/AN4 RE0/RD/AN5 RE1/WR/AN6 RE2/CS/AN7 VDD VSS 8 9 10 11 12 13 PIC16F871 * PIC16F870 Pin Diagram 32 31 RB7/PGD RB6/PGC RB5 RB4 RB3/PGM RB1 VSS 30 RD7/PSP7 29 28 14 27 RD6/PSP6 RD5/PSP5 RD4/PSP4 RC0/T1OSO/T1CKI 15 26 RC7/RX/DT RC1/T1OSI 16 17 25 24 RC6/TX/CK 18 23 19 20 22 21 RC4 RD3/PSP3 OSC1/CLKIN OSC2/CLKOUT RC2/CCP1 RC3 RD0/PSP0 RD1/PSP1 RC5 RD2/PSP2 Peripheral Features: * Timer0: 8-bit timer/counter with 8-bit prescaler * Timer1: 16-bit timer/counter with prescaler, can be incremented during sleep via external crystal/clock * Timer2: 8-bit timer/counter with 8-bit period register, prescaler and postscaler * One Capture, Compare, PWM module - Capture is 16-bit, max. resolution is 12.5 ns - Compare is 16-bit, max. resolution is 200 ns - PWM max. resolution is 10-bit * 10-bit multi-channel Analog-to-Digital converter * Universal Synchronous Asynchronous Receiver Transmitter (USART/SCI) with 9-bit address detection * Parallel Slave Port (PSP) 8-bits wide, with external RD, WR and CS controls (40/44-pin only) * Brown-out detection circuitry for Brown-out Reset (BOR) Preliminary DS30569A-page 1 PIC16F870/871 Pin Diagrams 28 27 26 25 24 23 22 21 20 19 18 17 16 15 RB7/PGD RB6/PGC RB5 RB4 RB3/PGM RB2 RB1 RB0/INT VDD VSS RC7/RX/DT RC6/TX/CK RC5 RC4 6 5 4 3 2 1 44 43 42 41 40 PLCC RA3/AN3/VREF+ RA2/AN2/VREFRA1/AN1 RA0/AN0 MCLR/VPP/THV NC RB7/PGD RB6/PGC RB5 RB4 NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 MCLR/VPP/THV RA0/AN0 RA1/AN1 RA2/AN2/VREFRA3/AN3/VREF+ RA4/T0CKI RA5/AN4 VSS OSC1/CLKIN OSC2/CLKOUT RC0/T1OSO/T1CKI RC1/T1OSI RC2/CCP1 RC3 PIC16F870 DIP, SOIC, SSOP 18 19 20 21 22 23 24 25 26 27 282 PIC16F871 39 38 37 36 35 34 33 32 31 30 9 RB3/PGM RB2 RB1 RB0/INT VDD VSS RD7/PSP7 RD6/PSP6 RD5/PSP5 RD4/PSP4 RC7/RX/DT RC6/TX/CK RC5 RC4 RD3/PSP3 RD2/PSP2 RD1/PSP1 RD0/PSP0 RC3 RC2/CCP1 RC1/T1OSI NC 44 43 42 41 40 39 38 37 36 35 34 TQFP 7 8 9 10 11 12 13 14 15 16 17 RC1/T1OSI RC2/CCP1 RC3 RD0/PSP0 RD1/PSP1 RD2/PSP2 RD3/PSP3 RC4 RC5 RC6/TX/CK NC RA4/T0CKI RA5/AN4 RE0/RD/AN5 RE1/WR/AN6 RE2/CS/AN7 VDD VSS OSC1/CLKIN OSC2/CLKOUT RC0/T1OSO/T1CK1 NC PIC16F871 33 32 31 30 29 28 27 26 25 24 23 12 13 14 15 16 17 18 19 20 21 22 1 2 3 4 5 6 7 8 9 10 11 NC RC0/T1OSO/T1CKI OSC2/CLKOUT OSC1/CLKIN VSS VDD RE2/AN7/CS RE1/AN6/WR RE0/AN5/RD RA5/AN4 RA4/T0CKI NC NC RB4 RB5 RB6/PGC RB7/PGD MCLR/VPP/THV RA0/AN0 RA1/AN1 RA2/AN2/VREFRA3/AN3/VREF+ RC7/RX/DT RD4/PSP4 RD5/PSP5 RD6/PSP6 RD7/PSP7 VSS VDD RB0/INT RB1 RB2 RB3/PGM DS30569A-page 2 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 Key Features PICmicroTM Mid-Range Reference Manual (DS33023) PIC16F870 PIC16F871 Operating Frequency DC - 20 MHz DC - 20 MHz Resets (and Delays) POR, BOR (PWRT, OST) POR, BOR (PWRT, OST) FLASH Program Memory (14-bit words) 2K 2K Data Memory (bytes) 128 128 EEPROM Data Memory 64 64 Interrupts 10 11 I/O Ports Ports A,B,C Ports A,B,C,D,E Timers 3 3 Capture/Compare/PWM modules 1 1 USART USART -- PSP 5 input channels 8 input channels 35 Instructions 35 Instructions Serial Communications Parallel Communications 10-bit Analog-to-Digital Module Instruction Set 1999 Microchip Technology Inc. Preliminary DS30569A-page 3 PIC16F870/871 Table of Contents 1.0 Device Overview ................................................................................................................................................... 5 2.0 Memory Organization.......................................................................................................................................... 11 3.0 I/O Ports .............................................................................................................................................................. 27 4.0 Data EEPROM and FLASH Program Memory.................................................................................................... 39 5.0 Timer0 Module .................................................................................................................................................... 47 6.0 Timer1 Module .................................................................................................................................................... 51 7.0 Timer2 Module .................................................................................................................................................... 55 8.0 Capture/Compare/PWM Module ......................................................................................................................... 57 9.0 Addressable Universal Synchronous Asynchronous Receiver Transmitter (USART) ........................................ 63 10.0 Analog-to-Digital Converter (A/D) Module........................................................................................................... 79 11.0 Special Features of the CPU............................................................................................................................... 89 12.0 Instruction Set Summary ................................................................................................................................... 105 13.0 Development Support ....................................................................................................................................... 113 14.0 Electrical Characteristics ................................................................................................................................... 119 15.0 DC and AC Characteristics Graphs and Tables................................................................................................ 135 16.0 Packaging Information ...................................................................................................................................... 137 Index .......................................................................................................................................................................... 145 On-Line Support .......................................................................................................................................................... 151 Reader Response ....................................................................................................................................................... 152 Product Identification System...................................................................................................................................... 153 To Our Valued Customers Most Current Data Sheet To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character of the literature number is the version number. e.g., DS30000A is version A of document DS30000. New Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products. Errata An errata sheet may exist for current devices, describing minor operational differences (from the data sheet) and recommended workarounds. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision of silicon and revision of document to which it applies. To determine if an errata sheet exists for a particular device, please check with one of the following: * Microchip's Worldwide Web site; http://www.microchip.com * Your local Microchip sales office (see last page) * The Microchip Corporate Literature Center; U.S. FAX: (480) 786-7277 When contacting a sales office or the literature center, please specify which device, revision of silicon and data sheet (include literature number) you are using. Corrections to this Data Sheet We constantly strive to improve the quality of all our products and documentation. We have spent a great deal of time to ensure that this document is correct. However, we realize that we may have missed a few things. If you find any information that is missing or appears in error, please: * Fill out and mail in the reader response form in the back of this data sheet. * E-mail us at webmaster@microchip.com. We appreciate your assistance in making this a better document. DS30569A-page 4 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 1.0 DEVICE OVERVIEW There are two devices (PIC16F870 and PIC16F871) covered by this data sheet. The PIC16F870 device comes in a 28-pin package and the PIC16F871 device comes in a 40-pin package. The 28-pin device does not have a Parallel Slave Port implemented. This document contains device-specific information. Additional information may be found in the PICmicroTM Mid-Range Reference Manual, (DS33023), which may be obtained from your local Microchip Sales Representative or downloaded from the Microchip website. The Reference Manual should be considered a complementary document to this data sheet, and is highly recommended reading for a better understanding of the device architecture and operation of the peripheral modules. FIGURE 1-1: The following two figures are device block diagrams sorted by pin number; 28-pin for Figure 1-1 and 40-pin for Figure 1-2. The 28-pin and 40-pin pinouts are listed in Table 1-1 and Table 1-2, respectively. PIC16F870 BLOCK DIAGRAM Device Program FLASH Data Memory Data EEPROM PIC16F870 2K 128 Bytes 64 Bytes 13 FLASH Program Memory PORTA RA0/AN0 RA1/AN1 RA2/AN2/VREFRA3/AN3/VREF+ RA4/T0CKI RA5/AN4 RAM File Registers 8 Level Stack (13-bit) Program Bus 8 Data Bus Program Counter 14 RAM Addr (1) PORTB 9 Addr MUX Instruction reg Direct Addr 7 8 Indirect Addr FSR reg STATUS reg 8 3 Power-up Timer Instruction Decode & Control Timing Generation OSC1/CLKIN OSC2/CLKOUT Oscillator Start-up Timer MUX ALU Power-on Reset PORTC RB0/INT RB1 RB2 RB3/PGM RB4 RB5 RB6/PGC RB7/PGD RC0/T1OSO/T1CKI RC1/T1OSI RC2/CCP1 RC3 RC4 RC5 RC6/TX/CK RC7/RX/DT 8 Watchdog Timer Brown-out Reset In-Circuit Debugger W reg Low-Voltage Programming MCLR Timer0 Data EEPROM Timer1 VDD, VSS Timer2 10-bit A/D USART CCP1 Note 1: Higher order bits are from the STATUS register. 1999 Microchip Technology Inc. Preliminary DS30569A-page 5 PIC16F870/871 FIGURE 1-2: PIC16F871 BLOCK DIAGRAM Device Program FLASH Data Memory Data EEPROM PIC16F871 2K 128 Bytes 64 Bytes 13 Program Memory 14 PORTA RA0/AN0 RA1/AN1 RA2/AN2/VREFRA3/AN3/VREF+ RA4/T0CKI RA5/AN4 RAM File Registers 8 Level Stack (13-bit) Program Bus 8 Data Bus Program Counter FLASH RAM Addr (1) PORTB 9 Addr MUX Instruction reg Direct Addr 7 8 Indirect Addr FSR reg STATUS reg 8 3 Power-up Timer Instruction Decode & Control Timing Generation OSC1/CLKIN OSC2/CLKOUT Oscillator Start-up Timer PORTC RC0/T1OSO/T1CKI RC1/T1OSI RC2/CCP1 RC3 RC4 RC5 RC6/TX/CK RC7/RX/DT MUX ALU Power-on Reset 8 Watchdog Timer Brown-out Reset RB0/INT RB1 RB2 RB3/PGM RB4 RB5 RB6/PGC RB7/PGD PORTD W reg RD7/PSP7:RD0/PSP0 In-Circuit Debugger Low-Voltage Programming PORTE RE0/AN5/RD RE1/AN6/WR MCLR Timer0 Data EEPROM Timer1 CCP1 VDD, VSS Timer2 Parallel Slave Port RE2/AN7/CS 10-bit A/D USART Note 1: Higher order bits are from the STATUS register. DS30569A-page 6 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 TABLE 1-1: PIC16F870 PINOUT DESCRIPTION DIP Pin# SOIC Pin# I/O/P Type OSC1/CLKIN 9 9 I OSC2/CLKOUT 10 10 O -- Oscillator crystal output. Connects to crystal or resonator in crystal oscillator mode. In RC mode, the OSC2 pin outputs CLKOUT which has 1/4 the frequency of OSC1, and denotes the instruction cycle rate. MCLR/VPP/THV 1 1 I/P ST Master clear (reset) input or programming voltage input or high voltage test mode control. This pin is an active low reset to the device. RA0/AN0 2 2 I/O TTL RA1/AN1 3 3 I/O TTL RA1 can also be analog input1 RA2/AN2/VREF- 4 4 I/O TTL RA2 can also be analog input2 or negative analog reference voltage RA3/AN3/VREF+ 5 5 I/O TTL RA3 can also be analog input3 or positive analog reference voltage RA4/T0CKI 6 6 I/O ST RA4 can also be the clock input to the Timer0 module. Output is open drain type. RA5/AN4 7 7 I/O TTL Pin Name Buffer Type Description ST/CMOS(3) Oscillator crystal input/external clock source input. PORTA is a bi-directional I/O port. RA0 can also be analog input0 RA5 can also be analog input4 PORTB is a bi-directional I/O port. PORTB can be software programmed for internal weak pull-up on all inputs. RB0/INT 21 21 I/O TTL/ST(1) RB1 22 22 I/O TTL RB2 23 23 I/O TTL RB3/PGM 24 24 I/O TTL/ST(1) RB4 25 25 I/O TTL RB5 26 26 I/O TTL RB6/PGC 27 27 I/O TTL/ST (2) Interrupt on change pin or In-Circuit Debugger pin. Serial programming clock. RB7/PGD 28 28 I/O TTL/ST(2) Interrupt on change pin or In-Circuit Debugger pin. Serial programming data. RC0/T1OSO/T1CKI 11 11 I/O ST RC0 can also be the Timer1 oscillator output or Timer1 clock input. RC1/T1OSI 12 12 I/O ST RC1 can also be the Timer1 oscillator input RC2/CCP1 13 13 I/O ST RC2 can also be the Capture1 input/Compare1 output/PWM1 output. RC3 14 14 I/O ST RC4 15 15 I/O ST RC5 16 16 I/O ST RC6/TX/CK 17 17 I/O ST RC6 can also be the USART Asynchronous Transmit or Synchronous Clock. RC7/RX/DT 18 18 I/O ST RC7 can also be the USART Asynchronous Receive or Synchronous Data. VSS 8, 19 8, 19 P -- Ground reference for logic and I/O pins. VDD 20 20 P -- Positive supply for logic and I/O pins. RB0 can also be the external interrupt pin. RB3 can also be the low voltage programming input Interrupt on change pin. Interrupt on change pin. PORTC is a bi-directional I/O port. Legend: I = input O = output I/O = input/output P = power -- = Not used TTL = TTL input ST = Schmitt Trigger input Note 1: This buffer is a Schmitt Trigger input when configured as the external interrupt or LVP mode. 2: This buffer is a Schmitt Trigger input when used in serial programming mode. 3: This buffer is a Schmitt Trigger input when configured in RC oscillator mode and a CMOS input otherwise. 1999 Microchip Technology Inc. Preliminary DS30569A-page 7 PIC16F870/871 TABLE 1-2: PIC16F871 PINOUT DESCRIPTION DIP Pin# PLCC Pin# QFP Pin# I/O/P Type Buffer Type OSC1/CLKIN 13 14 30 I ST/CMOS(4) OSC2/CLKOUT 14 15 31 O -- Oscillator crystal output. Connects to crystal or resonator in crystal oscillator mode. In RC mode, OSC2 pin outputs CLKOUT which has 1/4 the frequency of OSC1, and denotes the instruction cycle rate. MCLR/VPP/THV 1 2 18 I/P ST Master clear (reset) input or programming voltage input or high voltage test mode control. This pin is an active low reset to the device. RA0/AN0 2 3 19 I/O TTL RA0 can also be analog input0 RA1/AN1 3 4 20 I/O TTL RA1 can also be analog input1 RA2/AN2/VREF- 4 5 21 I/O TTL RA2 can also be analog input2 or negative analog reference voltage RA3/AN3/VREF+ 5 6 22 I/O TTL RA3 can also be analog input3 or positive analog reference voltage RA4/T0CKI 6 7 23 I/O ST RA4 can also be the clock input to the Timer0 timer/ counter. Output is open drain type. RA5/AN4 7 8 24 I/O TTL Pin Name Description Oscillator crystal input/external clock source input. PORTA is a bi-directional I/O port. RA5 can also be analog input4 PORTB is a bi-directional I/O port. PORTB can be software programmed for internal weak pull-up on all inputs. RB0/INT 33 36 8 I/O TTL/ST(1) RB0 can also be the external interrupt pin. RB1 34 37 9 I/O TTL RB2 35 38 10 I/O TTL RB3/PGM 36 39 11 I/O TTL/ST(1) RB4 37 41 14 I/O TTL RB5 38 42 15 I/O TTL RB6/PGC 39 43 16 I/O TTL/ST (2) Interrupt on change pin or In-Circuit Debugger pin. Serial programming clock. RB7/PGD 40 44 17 I/O TTL/ST(2) Interrupt on change pin or In-Circuit Debugger pin. Serial programming data. RC0/T1OSO/T1CKI 15 16 32 I/O ST RC0 can also be the Timer1 oscillator output or a Timer1 clock input. RC1/T1OSI 16 18 35 I/O ST RC1 can also be the Timer1 oscillator input RC2/CCP1 17 19 36 I/O ST RC2 can also be the Capture1 input/Compare1 output/ PWM1 output. RC3 18 20 37 I/O ST RC4 23 25 42 I/O ST RC5 24 26 43 I/O ST RC6/TX/CK 25 27 44 I/O ST RC6 can also be the USART Asynchronous Transmit or Synchronous Clock. RC7/RX/DT 26 29 1 I/O ST RC7 can also be the USART Asynchronous Receive or Synchronous Data. RB3 can also be the low voltage programming input Interrupt on change pin. Interrupt on change pin. PORTC is a bi-directional I/O port. Legend: Note 1: 2: 3: 4: I = input O = output I/O = input/output P = power -- = Not used TTL = TTL input ST = Schmitt Trigger input This buffer is a Schmitt Trigger input when configured as an external interrupt or LVP mode. This buffer is a Schmitt Trigger input when used in serial programming mode. This buffer is a Schmitt Trigger input when configured as general purpose I/O and a TTL input when used in the Parallel Slave Port mode (for interfacing to a microprocessor bus). This buffer is a Schmitt Trigger input when configured in RC oscillator mode and a CMOS input otherwise. DS30569A-page 8 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 TABLE 1-2: Pin Name PIC16F871 PINOUT DESCRIPTION (CONTINUED) DIP Pin# PLCC Pin# QFP Pin# I/O/P Type Buffer Type Description PORTD is a bi-directional I/O port or parallel slave port when interfacing to a microprocessor bus. RD0/PSP0 19 21 38 I/O ST/TTL(3) RD1/PSP1 20 22 39 I/O ST/TTL(3) RD2/PSP2 21 23 40 I/O ST/TTL(3) RD3/PSP3 22 24 41 I/O ST/TTL(3) RD4/PSP4 27 30 2 I/O ST/TTL(3) RD5/PSP5 28 31 3 I/O ST/TTL(3) RD6/PSP6 29 32 4 I/O ST/TTL(3) RD7/PSP7 30 33 5 I/O ST/TTL(3) RE0/RD/AN5 8 9 25 I/O ST/TTL(3) RE0 can also be read control for the parallel slave port, or analog input5. RE1/WR/AN6 9 10 26 I/O ST/TTL(3) RE1 can also be write control for the parallel slave port, or analog input6. RE2/CS/AN7 10 11 27 I/O ST/TTL(3) RE2 can also be select control for the parallel slave port, or analog input7. PORTE is a bi-directional I/O port. VSS 12,31 13,34 6,29 P -- Ground reference for logic and I/O pins. VDD 11,32 12,35 7,28 P -- Positive supply for logic and I/O pins. NC -- 1,17,28, 40 12,13, 33,34 -- These pins are not internally connected. These pins should be left unconnected. Legend: Note 1: 2: 3: 4: I = input O = output I/O = input/output P = power -- = Not used TTL = TTL input ST = Schmitt Trigger input This buffer is a Schmitt Trigger input when configured as an external interrupt or LVP mode. This buffer is a Schmitt Trigger input when used in serial programming mode. This buffer is a Schmitt Trigger input when configured as general purpose I/O and a TTL input when used in the Parallel Slave Port mode (for interfacing to a microprocessor bus). This buffer is a Schmitt Trigger input when configured in RC oscillator mode and a CMOS input otherwise. 1999 Microchip Technology Inc. Preliminary DS30569A-page 9 PIC16F870/871 NOTES: DS30569A-page 10 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 2.0 MEMORY ORGANIZATION 2.2 There are three memory blocks in each of these PICmicro (R) MCUs. The Program Memory and Data Memory have separate buses, so that concurrent access can occur, and is detailed in this section. The EEPROM data memory block is detailed in Section 4.0. Data Memory Organization The data memory is partitioned into multiple banks which contain the General Purpose Registers and the Special Function Registers. Bits RP1(STATUS<6>) and RP0 (STATUS<5>) are the bank select bits. RP<1:0> Bank Additional information on device memory may be found in the PICmicro Mid-Range Reference Manual, (DS33023). 00 0 01 1 10 2 2.1 11 3 Program Memory Organization The PIC16F870/871 devices have a 13-bit program counter capable of addressing an 8K x 14 program memory space. The PIC16F870/871 devices have 2K x 14 words of FLASH program memory. Accessing a location above the physically implemented address will cause a wraparound. The reset vector is at 0000h and the interrupt vector is at 0004h. FIGURE 2-1: PIC16F870/871 PROGRAM MEMORY MAP AND STACK Each bank extends up to 7Fh (128 bytes). The lower locations of each bank are reserved for the Special Function Registers. Above the Special Function Registers are General Purpose Registers, implemented as static RAM. All implemented banks contain Special Function Registers. Some "high use" Special Function Registers from one bank may be mirrored in another bank for code reduction and quicker access. Note: 2.2.1 EEPROM Data Memory description can be found in Section 4.0 of this Data Sheet GENERAL PURPOSE REGISTER FILE The register file can be accessed either directly, or indirectly through the File Select Register FSR. PC<12:0> 13 CALL, RETURN RETFIE, RETLW Stack Level 1 Stack Level 2 Stack Level 8 On-Chip Program Memory Reset Vector 0000h Interrupt Vector 0004h 0005h Page 0 07FFh 0800h 1FFFh 1999 Microchip Technology Inc. Preliminary DS30569A-page 11 PIC16F870/871 FIGURE 2-2: PIC16F870/871 REGISTER FILE MAP File Address Indirect addr.(*) TMR0 PCL STATUS FSR PORTA PORTB PORTC PORTD(2) PORTE(2) PCLATH INTCON PIR1 PIR2 TMR1L TMR1H T1CON TMR2 T2CON CCPR1L CCPR1H CCP1CON RCSTA TXREG RCREG ADRESH ADCON0 00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh 10h 11h 12h 13h 14h 15h 16h 17h 18h 19h 1Ah 1Bh 1Ch 1Dh 1Eh 1Fh 20h General Purpose Register File Address Indirect addr.(*) 80h OPTION_REG 81h PCL 82h STATUS 83h FSR 84h TRISA 85h TRISB 86h TRISC 87h TRISD(2) 88h TRISE(2) 89h PCLATH 8Ah INTCON 8Bh PIE1 8Ch PIE2 8Dh PCON 8Eh 8Fh 90h 91h PR2 92h 93h 94h 95h 96h 97h TXSTA 98h SPBRG 99h 9Ah 9Bh 9Ch 9Dh ADRESL 9Eh 9Fh ADCON1 General Purpose Register A0h 32 Bytes BFh C0h 96 Bytes 7Fh Bank 0 accesses 70h-7Fh Bank 1 Indirect addr.(*) 100h 101h TMR0 102h PCL 103h STATUS 104h FSR 105h 106h PORTB 107h 108h 109h 10Ah PCLATH 10Bh INTCON 10Ch EEDATA EEADR 10Dh 10Eh EEDATH 10Fh EEADRH 110h Indirect addr.(*) OPTION_REG PCL STATUS FSR TRISB PCLATH INTCON EECON1 EECON2 Reserved(1) Reserved(1) 180h 181h 182h 183h 184h 185h 186h 187h 188h 189h 18Ah 18Bh 18Ch 18Dh 18Eh 18Fh 190h 1A0h 120h accesses A0h - BFh accesses 20h-7Fh EFh F0h File Address File Address 1BFh 1C0h accesses 70h-7Fh FFh Bank 2 16Fh 170h 17Fh accesses 70h-7Fh 1EFh 1F0h 1FFh Bank 3 Unimplemented data memory locations, read as '0'. * Not a physical register. Note 1: These registers are reserved; maintain these registers clear. 2: These registers are not implemented on the PIC16F870. DS30569A-page 12 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 2.2.2 SPECIAL FUNCTION REGISTERS The Special Function Registers can be classified into two sets; core (CPU) and peripheral. Those registers associated with the core functions are described in detail in this section. Those related to the operation of the peripheral features are described in detail in the peripheral feature section. The Special Function Registers are registers used by the CPU and peripheral modules for controlling the desired operation of the device. These registers are implemented as static RAM. A list of these registers is given in Table 2-1. TABLE 2-1: Address SPECIAL FUNCTION REGISTER SUMMARY Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Value on: POR, BOR Bit 0 Value on all other resets (2) Bank 0 00h(4) INDF Addressing this location uses contents of FSR to address data memory (not a physical register) 0000 0000 0000 0000 01h TMR0 Timer0 module's register xxxx xxxx uuuu uuuu 02h(4) PCL Program Counter's (PC) Least Significant Byte 0000 0000 0000 0000 (4) 03h STATUS 04h(4) FSR 05h PORTA 06h PORTB PORTB Data Latch when written: PORTB pins when read xxxx xxxx uuuu uuuu 07h PORTC PORTC Data Latch when written: PORTC pins when read xxxx xxxx uuuu uuuu (5) PORTD PORTD Data Latch when written: PORTD pins when read xxxx xxxx uuuu uuuu (5) 08h IRP RP1 RP0 TO PD Z DC C 0001 1xxx 000q quuu Indirect data memory address pointer -- -- xxxx xxxx uuuu uuuu PORTA Data Latch when written: PORTA pins when read -- -- RE2 09h PORTE -- -- -- 0Ah(1,4) PCLATH -- -- -- 0Bh(4) INTCON GIE PEIE T0IE INTE RBIE T0IF INTF RBIF 0000 000x 0000 000u 0Ch PIR1 PSPIF(3) ADIF RCIF TXIF -- CCP1IF TMR2IF TMR1IF 0000 -000 0000 -000 -- -- -- EEIF -- -- -- -- ---0 ---- ---0 ---- 0Dh PIR2 TMR1L Holding register for the Least Significant Byte of the 16-bit TMR1 register 0Fh TMR1H Holding register for the Most Significant Byte of the 16-bit TMR1 register 10h T1CON 11h TMR2 12h T2CON -- RE0 ---- -xxx ---- -uuu Write Buffer for the upper 5 bits of the Program Counter 0Eh -- RE1 --0x 0000 --0u 0000 ---0 0000 ---0 0000 xxxx xxxx uuuu uuuu xxxx xxxx uuuu uuuu T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 -000 0000 Timer2 module's register -- --00 0000 --uu uuuu 0000 0000 0000 0000 13h 14h 15h CCPR1L Capture/Compare/PWM Register1 (LSB) 16h CCPR1H Capture/Compare/PWM Register1 (MSB) 17h CCP1CON 18h RCSTA 19h TXREG USART Transmit Data Register 0000 0000 0000 0000 1Ah RCREG USART Receive Data Register 0000 0000 0000 0000 ADRESH A/D Result Register High Byte xxxx xxxx uuuu uuuu xxxx xxxx uuuu uuuu -- -- CCP1X CCP1Y CCP1M3 CCP1M2 CCP1M1 CCP1M0 --00 0000 --00 0000 SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 0000 000x 0000 000x 1Bh 1Ch 1Dh 1Eh 1Fh ADCON0 ADCS1 ADCS0 CHS2 xxxx xxxx uuuu uuuu CHS1 CHS0 GO/ DONE -- ADON 0000 00-0 0000 00-0 Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented read as '0', r = reserved. Shaded locations are unimplemented, read as `0'. Note 1: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for the PC<12:8> whose contents are transferred to the upper byte of the program counter. 2: Other (non power-up) resets include external reset through MCLR and Watchdog Timer Reset. 3: Bits PSPIE and PSPIF are reserved on the 28-pin devices; always maintain these bits clear. 4: These registers can be addressed from any bank. 5: PORTD, PORTE, TRISD and TRISE are not physically implemented on the 28-pin devices, read as `0'. 1999 Microchip Technology Inc. Preliminary DS30569A-page 13 PIC16F870/871 TABLE 2-1: Address SPECIAL FUNCTION REGISTER SUMMARY (CONTINUED) Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR Value on all other resets (2) Bank 1 80h(4) INDF 81h OPTION_REG 82h(4) PCL 83h(4) STATUS 84h(4) FSR 85h TRISA Addressing this location uses contents of FSR to address data memory (not a physical register) RBPU INTEDG T0CS T0SE PS2 PS1 PS0 1111 1111 1111 1111 PD Z DC C 0001 1xxx 000q quuu Program Counter's (PC) Least Significant Byte IRP RP1 RP0 0000 0000 0000 0000 TO Indirect data memory address pointer -- -- 0000 0000 0000 0000 PSA xxxx xxxx uuuu uuuu PORTA Data Direction Register --11 1111 --11 1111 86h TRISB PORTB Data Direction Register 1111 1111 1111 1111 87h TRISC PORTC Data Direction Register 1111 1111 1111 1111 88h(5) TRISD PORTD Data Direction Register 89h(5) TRISE 8Ah(1,4) PCLATH -- -- -- INTCON GIE PEIE T0IE 8Bh (4) IBF OBF (3) IBOV 1111 1111 1111 1111 PSPMODE -- PORTE Data Direction Bits Write Buffer for the upper 5 bits of the Program Counter INTE RBIE T0IF INTF RBIF 0000 -111 0000 -111 ---0 0000 ---0 0000 0000 000x 0000 000u ADIE RCIE TXIE -- CCP1IE TMR2IE TMR1IE 0000 -000 0000 -000 -- -- -- EEIE -- -- -- -- ---0 ---- ---0 ---- -- -- -- -- -- -- POR BOR ---- --qq ---- --uu 8Ch PIE1 8Dh PIE2 8Eh PCON 8Fh -- Unimplemented -- -- 90h -- Unimplemented -- -- PR2 Timer2 Period Register 95h -- Unimplemented -- -- 96h -- Unimplemented -- -- 97h -- Unimplemented -- -- 98h TXSTA 99h SPBRG Baud Rate Generator Register 9Ah -- Unimplemented -- -- 9Bh -- Unimplemented -- -- 9Ch -- Unimplemented -- -- 9Dh -- Unimplemented -- -- 9Eh ADRESL A/D Result Register Low Byte 9Fh ADCON1 PSPIE 91h 92h 1111 1111 1111 1111 93h 94h CSRC ADFM TX9 -- TXEN -- -- SYNC BRGH TRMT TX9D 0000 -010 0000 -010 0000 0000 0000 0000 xxxx xxxx uuuu uuuu -- PCFG3 PCFG2 PCFG1 PCFG0 0--- 0000 0--- 0000 Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented read as '0', r = reserved. Shaded locations are unimplemented, read as `0'. Note 1: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for the PC<12:8> whose contents are transferred to the upper byte of the program counter. 2: Other (non power-up) resets include external reset through MCLR and Watchdog Timer Reset. 3: Bits PSPIE and PSPIF are reserved on the 28-pin devices; always maintain these bits clear. 4: These registers can be addressed from any bank. 5: PORTD, PORTE, TRISD and TRISE are not physically implemented on the 28-pin devices, read as `0'. DS30569A-page 14 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 TABLE 2-1: Address SPECIAL FUNCTION REGISTER SUMMARY (CONTINUED) Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR Value on all other resets (2) 0000 0000 0000 0000 Bank 2 100h(4) INDF Addressing this location uses contents of FSR to address data memory (not a physical register) 101h TMR0 Timer0 module's register 102h(4) PCL Program Counter's (PC) Least Significant Byte 103h(4) STATUS (4) IRP xxxx xxxx uuuu uuuu RP1 RP0 TO 0000 0000 0000 0000 PD Z DC C 0001 1xxx 000q quuu 104h FSR Indirect data memory address pointer 105h -- Unimplemented 106h PORTB PORTB Data Latch when written: PORTB pins when read 107h -- Unimplemented -- -- 108h -- Unimplemented -- -- 109h -- Unimplemented -- -- 10Ah (1,4) PCLATH xxxx xxxx uuuu uuuu -- -- -- -- GIE PEIE T0IE 10Bh(4) INTCON 10Ch EEDATA EEPROM data register 10Dh EEADR EEPROM address register 10Eh EEDATH -- -- 10Fh EEADRH -- -- Write Buffer for the upper 5 bits of the Program Counter INTE RBIE -- xxxx xxxx uuuu uuuu T0IF INTF RBIF ---0 0000 ---0 0000 0000 000x 0000 000u xxxx xxxx uuuu uuuu xxxx xxxx uuuu uuuu EEPROM data register high byte -- xxxx xxxx uuuu uuuu EEPROM address register high byte xxxx xxxx uuuu uuuu Bank 3 180h(4) INDF 181h OPTION_REG 182h(4) PCL 183h(4) STATUS (4) Addressing this location uses contents of FSR to address data memory (not a physical register) RBPU INTEDG T0CS T0SE PSA PS2 PS1 PS0 PD Z DC C Program Counter's (PC) Least Significant Byte IRP RP1 RP0 TO 0000 0000 0000 0000 1111 1111 1111 1111 0000 0000 0000 0000 0001 1xxx 000q quuu 184h FSR Indirect data memory address pointer 185h -- Unimplemented 186h TRISB PORTB Data Direction Register 187h -- Unimplemented -- -- 188h -- Unimplemented -- -- 189h -- Unimplemented -- -- 18Ah (1,4) PCLATH xxxx xxxx uuuu uuuu -- -- -- -- -- 1111 1111 1111 1111 Write Buffer for the upper 5 bits of the Program Counter ---0 0000 ---0 0000 18Bh(4) INTCON GIE PEIE T0IE INTE RBIE T0IF INTF RBIF 0000 000x 0000 000u 18Ch EECON1 EEPGD -- -- -- WRERR WREN WR RD x--- x000 x--- u000 18Dh EECON2 EEPROM control register2 (not a physical register) ---- ---- ---- ---- 18Eh -- Reserved maintain clear 0000 0000 0000 0000 18Fh -- Reserved maintain clear 0000 0000 0000 0000 Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented read as '0', r = reserved. Shaded locations are unimplemented, read as `0'. Note 1: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for the PC<12:8> whose contents are transferred to the upper byte of the program counter. 2: Other (non power-up) resets include external reset through MCLR and Watchdog Timer Reset. 3: Bits PSPIE and PSPIF are reserved on the 28-pin devices; always maintain these bits clear. 4: These registers can be addressed from any bank. 5: PORTD, PORTE, TRISD and TRISE are not physically implemented on the 28-pin devices, read as `0'. 1999 Microchip Technology Inc. Preliminary DS30569A-page 15 PIC16F870/871 2.2.2.1 STATUS REGISTER The STATUS Register contains the arithmetic status of the ALU, the RESET status and the bank select bits for data memory. The STATUS Register can be the destination for any instruction, as with any other register. If the STATUS Register is the destination for an instruction that affects the Z, DC or C bits, then the write to these three bits is disabled. These bits are set or cleared according to the device logic. Furthermore, the TO and PD bits are not writable, therefore, the result of an instruction with the STATUS Register as destination may be different than intended. For example, CLRF STATUS will clear the upper-three bits and set the Z bit. This leaves the STATUS register as 000u u1uu (where u = unchanged). It is recommended, therefore, that only BCF, BSF, SWAPF and MOVWF instructions are used to alter the STATUS register, because these instructions do not affect the Z, C or DC bits from the STATUS Register. For other instructions not affecting any status bits, see the "Instruction Set Summary." Note 1: The C and DC bits operate as a borrow and digit borrow bit, respectively, in subtraction. See the SUBLW and SUBWF instructions for examples. REGISTER 2-1: STATUS REGISTER (ADDRESS 03h, 83h, 103h, 183h) R/W-0 R/W-0 R/W-0 R-1 R-1 R/W-x R/W-x R/W-x IRP RP1 RP0 TO PD Z DC C bit7 bit 7: bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n= Value at POR reset IRP: Register Bank Select bit (used for indirect addressing) 1 = Bank 2, 3 (100h - 1FFh) 0 = Bank 0, 1 (00h - FFh) bit 6-5: RP1:RP0: Register Bank Select bits (used for direct addressing) 11 = Bank 3 (180h - 1FFh) 10 = Bank 2 (100h - 17Fh) 01 = Bank 1 (80h - FFh) 00 = Bank 0 (00h - 7Fh) Each bank is 128 bytes bit 4: TO: Time-out bit 1 = After power-up, CLRWDT instruction, or SLEEP instruction 0 = A WDT time-out occurred bit 3: PD: Power-down bit 1 = After power-up or by the CLRWDT instruction 0 = By execution of the SLEEP instruction bit 2: Z: Zero bit 1 = The result of an arithmetic or logic operation is zero 0 = The result of an arithmetic or logic operation is not zero bit 1: DC: Digit carry/borrow bit (ADDWF, ADDLW,SUBLW,SUBWF instructions) (for borrow the polarity is reversed) 1 = A carry-out from the 4th low order bit of the result occurred 0 = No carry-out from the 4th low order bit of the result bit 0: C: Carry/borrow bit (ADDWF, ADDLW,SUBLW,SUBWF instructions) 1 = A carry-out from the most significant bit of the result occurred 0 = No carry-out from the most significant bit of the result occurred Note: For borrow the polarity is reversed. A subtraction is executed by adding the two's complement of the second operand. For rotate (RRF, RLF) instructions, this bit is loaded with either the high or low order bit of the source register. DS30569A-page 16 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 2.2.2.2 OPTION_REG REGISTER The OPTION_REG Register is a readable and writable register, which contains various control bits to configure the TMR0 prescaler/WDT postscaler (single assignable register known also as the prescaler), the External INT Interrupt, TMR0 and the weak pull-ups on PORTB. Note: To achieve a 1:1 prescaler assignment for the TMR0 register, assign the prescaler to the Watchdog Timer. REGISTER 2-2: OPTION_REG REGISTER (ADDRESS 81h, 181h) R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 RBPU INTEDG T0CS T0SE PSA PS2 PS1 PS0 bit7 bit0 bit 7: RBPU: PORTB Pull-up Enable bit 1 = PORTB pull-ups are disabled 0 = PORTB pull-ups are enabled by individual port latch values bit 6: INTEDG: Interrupt Edge Select bit 1 = Interrupt on rising edge of RB0/INT pin 0 = Interrupt on falling edge of RB0/INT pin bit 5: T0CS: TMR0 Clock Source Select bit 1 = Transition on RA4/T0CKI pin 0 = Internal instruction cycle clock (CLKOUT) bit 4: T0SE: TMR0 Source Edge Select bit 1 = Increment on high-to-low transition on RA4/T0CKI pin 0 = Increment on low-to-high transition on RA4/T0CKI pin bit 3: PSA: Prescaler Assignment bit 1 = Prescaler is assigned to the WDT 0 = Prescaler is assigned to the Timer0 module R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n= Value at POR reset bit 2-0: PS2:PS0: Prescaler Rate Select bits Bit Value 000 001 010 011 100 101 110 111 TMR0 Rate 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128 1 : 256 1999 Microchip Technology Inc. WDT Rate 1:1 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128 Preliminary DS30569A-page 17 PIC16F870/871 2.2.2.3 INTCON REGISTER The INTCON Register is a readable and writable register, which contains various enable and flag bits for the TMR0 register overflow, RB Port change and External RB0/INT pin interrupts. Note: Interrupt flag bits get set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the global enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt. REGISTER 2-3: INTCON REGISTER (ADDRESS 0Bh, 8Bh, 10Bh, 18Bh) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 GIE PEIE T0IE INTE RBIE T0IF INTF bit7 R/W-x RBIF bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n= Value at POR reset bit 7: GIE: Global Interrupt Enable bit 1 = Enables all un-masked interrupts 0 = Disables all interrupts bit 6: PEIE: Peripheral Interrupt Enable bit 1 = Enables all un-masked peripheral interrupts 0 = Disables all peripheral interrupts bit 5: T0IE: TMR0 Overflow Interrupt Enable bit 1 = Enables the TMR0 interrupt 0 = Disables the TMR0 interrupt bit 4: INTE: RB0/INT External Interrupt Enable bit 1 = Enables the RB0/INT external interrupt 0 = Disables the RB0/INT external interrupt bit 3: RBIE: RB Port Change Interrupt Enable bit 1 = Enables the RB port change interrupt 0 = Disables the RB port change interrupt bit 2: T0IF: TMR0 Overflow Interrupt Flag bit 1 = TMR0 register has overflowed (must be cleared in software) 0 = TMR0 register did not overflow bit 1: INTF: RB0/INT External Interrupt Flag bit 1 = The RB0/INT external interrupt occurred (must be cleared in software) 0 = The RB0/INT external interrupt did not occur bit 0: RBIF: RB Port Change Interrupt Flag bit 1 = At least one of the RB7:RB4 pins changed state (must be cleared in software) 0 = None of the RB7:RB4 pins have changed state DS30569A-page 18 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 2.2.2.4 PIE1 REGISTER The PIE1 Register contains the individual enable bits for the peripheral interrupts. Note: Bit PEIE (INTCON<6>) must be set to enable any peripheral interrupt. R/W-0 R/W-0 REGISTER 2-4: PIE1 REGISTER (ADDRESS 8Ch) R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 PSPIE(1) ADIE RCIE TXIE CCP1IE TMR2IE TMR1IE bit7 bit0 bit 7: PSPIE(1): Parallel Slave Port Read/Write Interrupt Enable bit 1 = Enables the PSP read/write interrupt 0 = Disables the PSP read/write interrupt bit 6: ADIE: A/D Converter Interrupt Enable bit 1 = Enables the A/D converter interrupt 0 = Disables the A/D converter interrupt bit 5: RCIE: USART Receive Interrupt Enable bit 1 = Enables the USART receive interrupt 0 = Disables the USART receive interrupt bit 4: TXIE: USART Transmit Interrupt Enable bit 1 = Enables the USART transmit interrupt 0 = Disables the USART transmit interrupt bit 3: Unimplemented: Read as `0' bit 2: CCP1IE: CCP1 Interrupt Enable bit 1 = Enables the CCP1 interrupt 0 = Disables the CCP1 interrupt bit 1: TMR2IE: TMR2 to PR2 Match Interrupt Enable bit 1 = Enables the TMR2 to PR2 match interrupt 0 = Disables the TMR2 to PR2 match interrupt bit 0: TMR1IE: TMR1 Overflow Interrupt Enable bit 1 = Enables the TMR1 overflow interrupt 0 = Disables the TMR1 overflow interrupt R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n= Value at POR reset Note 1: PSPIE is reserved on the PIC16F870; always maintain this bit clear. 1999 Microchip Technology Inc. Preliminary DS30569A-page 19 PIC16F870/871 2.2.2.5 PIR1 REGISTER The PIR1 Register contains the individual flag bits for the peripheral interrupts. Note: Interrupt flag bits get set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the global enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt bits are clear prior to enabling an interrupt. R/W-0 R/W-0 REGISTER 2-5: PIR1 REGISTER (ADDRESS 0Ch) R/W-0 R/W-0 R-0 R-0 U-0 R/W-0 PSPIF(1) ADIF RCIF TXIF CCP1IF TMR2IF TMR1IF bit7 bit0 bit 7: PSPIF(1): Parallel Slave Port Read/Write Interrupt Flag bit 1 = A read or a write operation has taken place (must be cleared in software) 0 = No read or write has occurred bit 6: ADIF: A/D Converter Interrupt Flag bit 1 = An A/D conversion completed 0 = The A/D conversion is not complete bit 5: RCIF: USART Receive Interrupt Flag bit 1 = The USART receive buffer is full 0 = The USART receive buffer is empty bit 4: TXIF: USART Transmit Interrupt Flag bit 1 = The USART transmit buffer is empty 0 = The USART transmit buffer is full bit 7: Unimplemented: Read as `0' bit 2: CCP1IF: CCP1 Interrupt Flag bit Capture Mode 1 = A TMR1 register capture occurred (must be cleared in software) 0 = No TMR1 register capture occurred Compare Mode 1 = A TMR1 register compare match occurred (must be cleared in software) 0 = No TMR1 register compare match occurred PWM Mode Unused in this mode bit 1: TMR2IF: TMR2 to PR2 Match Interrupt Flag bit 1 = TMR2 to PR2 match occurred (must be cleared in software) 0 = No TMR2 to PR2 match occurred R = Readable bit W = Writable bit - n= Value at POR reset bit 0: TMR1IF: TMR1 Overflow Interrupt Flag bit 1 = TMR1 register overflowed (must be cleared in software) 0 = TMR1 register did not overflow Note 1: PSPIF is reserved on the PIC16F870; always maintain this bit clear. DS30569A-page 20 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 2.2.2.6 PIE2 REGISTER The PIE2 Register contains the individual enable bit for the EEPROM write operation interrupt. REGISTER 2-6: PIE2 REGISTER (ADDRESS 8Dh) U-0 U-0 U-0 R/W-0 U-0 U-0 U-0 U-0 -- -- -- EEIE -- -- -- -- bit7 bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n= Value at POR reset bit 7-5: Unimplemented: Read as '0' bit 4: EEIE: EEPROM Write Operation Interrupt Enable 1 = Enable EE Write Interrupt 0 = Disable EE Write Interrupt bit 3-0: Unimplemented: Read as '0' 1999 Microchip Technology Inc. Preliminary DS30569A-page 21 PIC16F870/871 2.2.2.7 PIR2 REGISTER . Note: The PIR2 Register contains the flag bit for the EEPROM write operation interrupt. Interrupt flag bits get set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the global enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt. REGISTER 2-7: PIR2 REGISTER (ADDRESS 0Dh) U-0 U-0 U-0 R/W-0 U-0 U-0 U-0 U-0 -- -- -- EEIF -- -- -- -- bit7 bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n= Value at POR reset bit 7-5: Unimplemented: Read as '0' bit 4: EEIF: EEPROM Write Operation Interrupt Flag bit 1 = The write operation completed (must be cleared in software) 0 = The write operation is not complete or has not been started bit 3-0: Unimplemented: Read as '0' DS30569A-page 22 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 2.2.2.8 PCON REGISTER Note: The Power Control (PCON) Register contains flag bits to allow differentiation between a Power-on Reset (POR), a Brown-out Reset (BOR), a Watch-dog Reset (WDT) and an external MCLR Reset. BOR is unknown on POR. It must be set by the user and checked on subsequent rests to see if BOR is clear, indicating a brownout has occurred. The BOR status bit is a don't care and is not predictable if the brown-out circuit is disabled (by clearing the BODEN bit in the configuration word). REGISTER 2-8: PCON REGISTER (ADDRESS 8Eh) U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 -- -- -- -- -- -- POR bit7 R/W-1 BOR bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n= Value at POR reset bit 7-2: Unimplemented: Read as '0' bit 1: POR: Power-on Reset Status bit 1 = No Power-on Reset occurred 0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs) bit 0: BOR: Brown-out Reset Status bit 1 = No Brown-out Reset occurred 0 = A Brown-out Reset occurred (must be set in software after a Brown-out Reset occurs) 1999 Microchip Technology Inc. Preliminary DS30569A-page 23 PIC16F870/871 2.3 PCL and PCLATH The Program Counter (PC) is 13-bits wide. The low byte comes from the PCL Register, which is a readable and writable register. The upper bits (PC<12:8>) are not readable, but are indirectly writable through the PCLATH register. On any reset, the upper bits of the PC will be cleared. Figure 2-3 shows the two situations for the loading of the PC. The upper example in the figure shows how the PC is loaded on a write to PCL (PCLATH<4:0> PCH). The lower example in the figure shows how the PC is loaded during a CALL or GOTO instruction (PCLATH<4:3> PCH). FIGURE 2-3: LOADING OF PC IN DIFFERENT SITUATIONS PCH PCL 12 8 7 0 PC 5 8 PCLATH<4:0> Instruction with PCL as Destination ALU PCLATH PCH 12 11 10 PCL 8 PC PCLATH<4:3> 11 Opcode <10:0> PCLATH COMPUTED GOTO A computed GOTO is accomplished by adding an offset to the program counter (ADDWF PCL). When doing a table read using a computed GOTO method, care should be exercised if the table location crosses a PCL memory boundary (each 256 byte block). Refer to the application note, "Implementing a Table Read" (AN556). 2.3.2 2.4 Program Memory Paging The PIC16FXXX architecture is capable of addressing a continuous 8K word block of program memory. The CALL and GOTO instructions provide 11 bits of the address, which allows branches within any 2K program memory page. Therefore, the 8K words of program memory are broken into four pages. Since the PIC16F872 has only 2K words of program memory or one page, additional code is not required to ensure that the correct page is selected before a CALL or GOTO instruction is executed. The PCLATH<4:3> bits should always be maintained as zeros. If a return from a CALL instruction (or interrupt) is executed, the entire 13-bit PC is popped off the stack. Manipulation of the PCLATH is not required for the return instructions. GOTO,CALL 2 2.3.1 2: There are no instructions/mnemonics called PUSH or POP. These are actions that occur from the execution of the CALL, RETURN, RETLW and RETFIE instructions or the vectoring to an interrupt address. 2.5 0 7 Note 1: There are no status bits to indicate stack overflow or stack underflow conditions. Indirect Addressing, INDF and FSR Registers The INDF Register is not a physical register. Addressing the INDF Register will cause indirect addressing. Indirect addressing is possible by using the INDF Register. Any instruction using the INDF Register actually accesses the register pointed to by the File Select Register, FSR. Reading the INDF Register itself indirectly (FSR = '0') will read 00h. Writing to the INDF Register indirectly results in a no-operation (although status bits may be affected). An effective 9-bit address is obtained by concatenating the 8-bit FSR Register and the IRP bit (STATUS<7>), as shown in Figure 2-4. A simple program to clear RAM locations 20h-2Fh using indirect addressing is shown in Example 2-1. EXAMPLE 2-1: STACK The PIC16FXXX family has an 8-level deep x 13-bit wide hardware stack. The stack space is not part of either program or data space and the stack pointer is not readable or writable. The PC is PUSHed onto the stack when a CALL instruction is executed or an interrupt causes a branch. The stack is POPed in the event of a RETURN,RETLW or a RETFIE instruction execution. PCLATH is not affected by a PUSH or POP operation. NEXT movlw movwf clrf incf btfss goto INDIRECT ADDRESSING 0x20 FSR INDF FSR,F FSR,4 NEXT ;initialize pointer ;to RAM ;clear INDF register ;inc pointer ;all done? ;no clear next CONTINUE : ;yes continue The stack operates as a circular buffer. This means that after the stack has been PUSHed eight times, the ninth push overwrites the value that was stored from the first push. The tenth push overwrites the second push (and so on). DS30569A-page 24 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 FIGURE 2-4: DIRECT/INDIRECT ADDRESSING Direct Addressing Indirect Addressing from opcode RP1:RP0 6 bank select location select 0 IRP 7 bank select 00 01 10 FSR register 0 location select 11 00h 80h 100h 180h 7Fh FFh 17Fh 1FFh Data Memory(1) Bank 0 Note 1: Bank 1 Bank 2 Bank 3 For register file map detail see Figure 2-2. 1999 Microchip Technology Inc. Preliminary DS30569A-page 25 PIC16F870/871 NOTES: DS30569A-page 26 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 3.0 I/O PORTS FIGURE 3-1: Some pins for these I/O ports are multiplexed with an alternate function for the peripheral features on the device. In general, when a peripheral is enabled, that pin may not be used as a general purpose I/O pin. Additional information on I/O ports may be found in the PICmicroTM Mid-Range Reference Manual, (DS33023). Data Bus BLOCK DIAGRAM OF RA3:RA0 AND RA5 PINS D Q VDD WR Port Q CK P Data Latch 3.1 PORTA and the TRISA Register D PORTA is a 6-bit wide bi-directional port. The corresponding data direction register is TRISA. Setting a TRISA bit (=1) will make the corresponding PORTA pin an input (i.e., put the corresponding output driver in a hi-impedance mode). Clearing a TRISA bit (=0) will make the corresponding PORTA pin an output (i.e., put the contents of the output latch on the selected pin). WR TRIS TRIS Latch Other PORTA pins are multiplexed with analog inputs and analog VREF input. The operation of each pin is selected by clearing/setting the control bits in the ADCON1 Register (A/D Control Register1). Note: Q RD PORT To A/D Converter Note 1: I/O pins have protection diodes to VDD and VSS. FIGURE 3-2: Data Bus The TRISA Register controls the direction of the RA pins, even when they are being used as analog inputs. The user must ensure the bits in the TRISA Register are maintained set when using them as analog inputs. WR PORT STATUS, RP0 STATUS, RP1 PORTA BSF MOVLW MOVWF MOVLW STATUS, RP0 0x06 ADCON1 0xCF MOVWF TRISA ; ; ; ; ; ; ; ; ; ; ; ; ; ; ; BLOCK DIAGRAM OF RA4/ T0CKI PIN D Q CK Q N I/O pin(1) Data Latch INITIALIZING PORTA BCF BCF CLRF D EN On a Power-on Reset, these pins are configured as analog inputs and read as '0'. EXAMPLE 3-1: TTL Input Buffer RD TRIS Reading the PORTA Register reads the status of the pins, whereas writing to it will write to the port latch. All write operations are read-modify-write operations. Therefore, a write to a port implies that the port pins are read, the value is modified and then written to the port data latch. Pin RA4 is multiplexed with the Timer0 module clock input to become the RA4/T0CKI pin. The RA4/T0CKI pin is a Schmitt Trigger input and an open drain output. All other PORTA pins have TTL input levels and full CMOS output drivers. VSS Analog Input Mode Q CK I/O pin(1) N Q WR TRIS Bank0 Initialize PORTA by clearing output data latches Select Bank 1 Configure all pins as digital inputs Value used to initialize data direction Set RA<3:0> as inputs RA<5:4> as outputs TRISA<7:6> are always read as '0'. D Q CK Q VSS Schmitt Trigger Input Buffer TRIS Latch RD TRIS Q D ENEN RD PORT TMR0 clock input Note 1: I/O pin has protection diodes to VSS only. 1999 Microchip Technology Inc. Preliminary DS30569A-page 27 PIC16F870/871 TABLE 3-1: PORTA FUNCTIONS Name Bit# Buffer Function RA0/AN0 bit0 TTL Input/output or analog input RA1/AN1 bit1 TTL Input/output or analog input RA2/AN2 bit2 TTL Input/output or analog input RA3/AN3/VREF bit3 TTL Input/output or analog input or VREF RA4/T0CKI bit4 ST Input/output or external clock input for Timer0 Output is open drain type RA5/AN4 bit5 TTL Input/output or analog input Legend: TTL = TTL input, ST = Schmitt Trigger input TABLE 3-2: Address SUMMARY OF REGISTERS ASSOCIATED WITH PORTA Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 RA5 RA4 RA3 RA2 RA1 RA0 05h PORTA -- -- 85h TRISA -- -- 9Fh ADCON1 ADFM -- PORTA Data Direction Register -- -- Value on: POR, BOR Value on all other resets --0x 0000 --0u 0000 --11 1111 --11 1111 PCFG3 PCFG2 PCFG1 PCFG0 --0- 0000 --0- 0000 Legend: x = unknown, u = unchanged, - = unimplemented locations read as '0'. Shaded cells are not used by PORTA. DS30569A-page 28 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 3.2 PORTB and the TRISB Register PORTB is an 8-bit wide, bi-directional port. The corresponding data direction register is TRISB. Setting a TRISB bit (=1) will make the corresponding PORTB pin an input (i.e., put the corresponding output driver in a hi-impedance mode). Clearing a TRISB bit (=0) will make the corresponding PORTB pin an output (i.e., put the contents of the output latch on the selected pin). Three pins of PORTB are multiplexed with the Low Voltage Programming function; RB3/PGM, RB6/PGC and RB7/PGD. The alternate functions of these pins are described in the Special Features Section. Each of the PORTB pins has a weak internal pull-up. A single control bit can turn on all the pull-ups. This is performed by clearing bit RBPU (OPTION_REG<7>). The weak pull-up is automatically turned off when the port pin is configured as an output. The pull-ups are disabled on a Power-on Reset. FIGURE 3-3: BLOCK DIAGRAM OF RB3:RB0 PINS Data Bus WR Port weak P pull-up Data Latch D Q Any read or write of PORTB. This will end the mismatch condition. Clear flag bit RBIF. b) A mismatch condition will continue to set flag bit RBIF. Reading PORTB will end the mismatch condition and allow flag bit RBIF to be cleared. The interrupt on change feature is recommended for wake-up on key depression operation and operations where PORTB is only used for the interrupt on change feature. Polling of PORTB is not recommended while using the interrupt on change feature. This interrupt on mismatch feature, together with software configurable pull-ups on these four pins, allow easy interface to a keypad and make it possible for wake-up on key-depression. Refer to the Embedded Control Handbook, "Implementing Wake-Up on Key Stroke" (AN552). RB0/INT is discussed in detail in Section 11.10.1. FIGURE 3-4: I/O pin(1) CK VDD TTL Input Buffer CK weak P pull-up Data Latch D Q Data Bus WR Port Q TRIS Latch D Q D WR TRIS RD Port TTL Input Buffer CK EN RB0/INT RB3/PGM RD TRIS Schmitt Trigger Buffer 1: 2: I/O pin(1) CK RD TRIS Note BLOCK DIAGRAM OF RB7:RB4 PINS RBPU(2) TRIS Latch D Q WR TRIS a) RB0/INT is an external interrupt input pin and is configured using the INTEDG bit (OPTION_REG<6>). VDD RBPU(2) This interrupt can wake the device from SLEEP. The user, in the interrupt service routine, can clear the interrupt in the following manner: RD Port I/O pins have diode protection to VDD and VSS. To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (OPTION_REG<7>). Four of PORTB's pins, RB7:RB4, have an interrupt on change feature. Only pins configured as inputs can cause this interrupt to occur (i.e. any RB7:RB4 pin configured as an output is excluded from the interrupt on change comparison). The input pins (of RB7:RB4) are compared with the old value latched on the last read of PORTB. The "mismatch" outputs of RB7:RB4 are OR'ed together to generate the RB Port Change Interrupt with flag bit RBIF (INTCON<0>). 1999 Microchip Technology Inc. Q Latch D EN RD Port ST Buffer Q1 Set RBIF From other RB7:RB4 pins Q D RD Port EN Q3 RB7:RB6 in serial programming mode Note Preliminary 1: 2: I/O pins have diode protection to VDD and VSS. To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (OPTION_REG<7>). DS30569A-page 29 PIC16F870/871 TABLE 3-3: Name PORTB FUNCTIONS Bit# Buffer RB0/INT bit0 TTL/ST(1) Function RB1 bit1 TTL RB2 bit2 TTL RB3/PGM bit3 TTL/ST(1) RB4 bit4 TTL Input/output pin (with interrupt on change). Internal software programmable weak pull-up. RB5 bit5 TTL Input/output pin (with interrupt on change). Internal software programmable weak pull-up. RB6/PGC bit6 TTL/ST(2) Input/output pin (with interrupt on change) or In-Circuit Debugger pin. Internal software programmable weak pull-up. Serial programming clock. RB7/PGD bit7 TTL/ST(2) Input/output pin (with interrupt on change) or In-Circuit Debugger pin. Internal software programmable weak pull-up. Serial programming data. Input/output pin or external interrupt input. Internal software programmable weak pull-up. Input/output pin. Internal software programmable weak pull-up. Input/output pin. Internal software programmable weak pull-up. Input/output pin or programming pin in LVP mode. Internal software programmable weak pull-up. Legend: TTL = TTL input, ST = Schmitt Trigger input Note 1: This buffer is a Schmitt Trigger input when configured as the external interrupt or LVP mode. 2: This buffer is a Schmitt Trigger input when used in serial programming mode. TABLE 3-4: Address SUMMARY OF REGISTERS ASSOCIATED WITH PORTB Name 06h, 106h PORTB 86h, 186h TRISB 81h, 181h OPTION_REG Value on: POR, BOR Value on all other resets Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0 xxxx xxxx uuuu uuuu T0SE PSA PS2 PS1 PS0 1111 1111 1111 1111 PORTB Data Direction Register RBPU INTEDG T0CS 1111 1111 1111 1111 Legend: x = unknown, u = unchanged. Shaded cells are not used by PORTB. DS30569A-page 30 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 3.3 PORTC and the TRISC Register PORTC is an 8-bit wide, bi-directional port. The corresponding data direction register is TRISC. Setting a TRISC bit (=1) will make the corresponding PORTC pin an input (i.e., put the corresponding output driver in a hi-impedance mode). Clearing a TRISC bit (=0) will make the corresponding PORTC pin an output (i.e., put the contents of the output latch on the selected pin). PORTC is multiplexed with several peripheral functions (Table 3-5). PORTC pins have Schmitt Trigger input buffers. When enabling peripheral functions, care should be taken in defining TRIS bits for each PORTC pin. Some peripherals override the TRIS bit to make a pin an output, while other peripherals override the TRIS bit to make a pin an input. Since the TRIS bit override is in effect while the peripheral is enabled, read-modifywrite instructions (BSF, BCF, XORWF) with TRISC as destination should be avoided. The user should refer to the corresponding peripheral section for the correct TRIS bit settings. FIGURE 3-5: PORTC BLOCK DIAGRAM (PERIPHERAL OUTPUT OVERRIDE) PORT/PERIPHERAL Select(2) Peripheral Data Out Data Bus WR PORT VDD 0 D Q P 1 CK Q Data Latch WR TRIS D CK I/O pin(1) Q Q N TRIS Latch VSS Schmitt Trigger RD TRIS Peripheral OE(3) Q RD PORT Peripheral Input D EN Note 1: I/O pins have diode protection to VDD and VSS. 2: Port/Peripheral select signal selects between port data and peripheral output. 3: Peripheral OE (output enable) is only activated if peripheral select is active. 1999 Microchip Technology Inc. Preliminary DS30569A-page 31 PIC16F870/871 TABLE 3-5: PORTC FUNCTIONS Name Bit# Buffer Type Function RC0/T1OSO/T1CKI bit0 ST Input/output port pin or Timer1 oscillator output/Timer1 clock input RC1/T1OSI bit1 ST Input/output port pin or Timer1 oscillator input RC2/CCP1 bit2 ST Input/output port pin or Capture1 input/Compare1 output/PWM1 output RC3 bit3 ST Input/output port pin RC4 bit4 ST Input/output port pin RC5 bit5 ST Input/output port pin RC6/TX/CK bit6 ST Input/output port pin or USART Asynchronous Transmit or Synchronous Clock RC7/RX/DT bit7 ST Input/output port pin or USART Asynchronous Receive or Synchronous Data Legend: ST = Schmitt Trigger input TABLE 3-6: SUMMARY OF REGISTERS ASSOCIATED WITH PORTC Value on all other resets Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR 07h PORTC RC7 RC6 RC5 RC4 RC3 RC2 RC1 RC0 xxxx xxxx uuuu uuuu 87h TRISC 1111 1111 1111 1111 Address PORTC Data Direction Register Legend: x = unknown, u = unchanged. DS30569A-page 32 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 3.4 PORTD and TRISD Registers FIGURE 3-6: PORTD BLOCK DIAGRAM (IN I/O PORT MODE) This section is not applicable to the PIC16F870. Data Bus PORTD is an 8-bit port with Schmitt Trigger input buffers. Each pin is individually configurable as an input or output. D WR PORT PORTD can be configured as an 8-bit wide microprocessor port (parallel slave port) by setting control bit PSPMODE (TRISE<4>). In this mode, the input buffers are TTL. Q I/O pin(1) CK Data Latch D WR TRIS Q Schmitt Trigger Input Buffer CK TRIS Latch RD TRIS Q D ENEN RD PORT Note 1: I/O pins have protection diodes to VDD and VSS. TABLE 3-7: Name PORTD FUNCTIONS Bit# Buffer Type Function (1) Input/output port pin or parallel slave port bit0 RD0/PSP0 bit0 ST/TTL RD1/PSP1 bit1 ST/TTL(1) Input/output port pin or parallel slave port bit1 RD2/PSP2 bit2 ST/TTL (1) Input/output port pin or parallel slave port bit2 RD3/PSP3 bit3 ST/TTL(1) Input/output port pin or parallel slave port bit3 RD4/PSP4 bit4 ST/TTL(1) Input/output port pin or parallel slave port bit4 RD5/PSP5 bit5 ST/TTL(1) Input/output port pin or parallel slave port bit5 RD6/PSP6 bit6 ST/TTL(1) Input/output port pin or parallel slave port bit6 RD7/PSP7 bit7 ST/TTL(1) Input/output port pin or parallel slave port bit7 Legend: ST = Schmitt Trigger input TTL = TTL input Note 1: Input buffers are Schmitt Triggers when in I/O mode and TTL buffer when in Parallel Slave Port Mode. TABLE 3-8: SUMMARY OF REGISTERS ASSOCIATED WITH PORTD Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR 08h PORTD RD7 RD6 RD5 RD4 RD3 RD2 RD1 RD0 xxxx xxxx 88h TRISD 1111 1111 1111 1111 89h TRISE PORTE Data Direction Bits 0000 -111 0000 -111 Address PORTD Data Direction Register IBF OBF IBOV PSPMODE -- Value on all other resets uuuu uuuu Legend: x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by PORTD. 1999 Microchip Technology Inc. Preliminary DS30569A-page 33 PIC16F870/871 3.5 PORTE and TRISE Register FIGURE 3-7: This section is not applicable to the PIC16F870. Data Bus PORTE has three pins, RE0/RD/AN5, RE1/WR/AN6 and RE2/CS/AN7, which are individually configurable as inputs or outputs. These pins have Schmitt Trigger input buffers. WR PORT PORTE BLOCK DIAGRAM (IN I/O PORT MODE) D Q I/O pin(1) CK Data Latch I/O PORTE becomes control inputs for the microprocessor port when bit PSPMODE (TRISE<4>) is set. In this mode, the user must make sure that the TRISE<2:0> bits are set (pins are configured as digital inputs). Ensure ADCON1 is configured for digital I/O. In this mode, the input buffers are TTL. D WR TRIS Q TRIS Latch Register 3-1 shows the TRISE Register, which also controls the parallel slave port operation. RD TRIS PORTE pins are multiplexed with analog inputs. When selected as an analog input, these pins will read as '0's. Q TRISE controls the direction of the RE pins, even when they are being used as analog inputs. The user must make sure to keep the pins configured as inputs when using them as analog inputs. Note: Schmitt Trigger input buffer CK D EN RD PORT Note 1: I/O pins have protection diodes to VDD and VSS. On a Power-on Reset, these pins are configured as analog inputs. REGISTER 3-1: TRISE REGISTER (ADDRESS 89h) R-0 R-0 R/W-0 R/W-0 U-0 R/W-1 R/W-1 IBF OBF IBOV PSPMODE -- bit2 bit1 bit7 R/W-1 bit0 bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n= Value at POR reset Parallel Slave Port Status/Control Bits bit 7 : IBF: Input Buffer Full Status bit 1 = A word has been received and is waiting to be read by the CPU 0 = No word has been received bit 6: OBF: Output Buffer Full Status bit 1 = The output buffer still holds a previously written word 0 = The output buffer has been read bit 5: IBOV: Input Buffer Overflow Detect bit (in microprocessor mode) 1 = A write occurred when a previously input word has not been read (must be cleared in software) 0 = No overflow occurred bit 4: PSPMODE: Parallel Slave Port Mode Select bit 1 = Parallel slave port mode 0 = General purpose I/O mode bit 3: Unimplemented: Read as '0' PORTE Data Direction Bits bit 2: Bit2: Direction Control bit for pin RE2/CS/AN7 1 = Input 0 = Output bit 1: Bit1: Direction Control bit for pin RE1/WR/AN6 1 = Input 0 = Output bit 0: Bit0: Direction Control bit for pin RE0/RD/AN5 1 = Input 0 = Output DS30569A-page 34 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 TABLE 3-9: Name PORTE FUNCTIONS Bit# Buffer Type Function (1) Input/output port pin or read control input in parallel slave port mode or analog input: RD 1 = Not a read operation 0 = Read operation. Reads PORTD register (if chip selected) RE0/RD/AN5 bit0 ST/TTL RE1/WR/AN6 bit1 ST/TTL(1) Input/output port pin or write control input in parallel slave port mode or analog input: WR 1 = Not a write operation 0 = Write operation. Writes PORTD register (if chip selected) RE2/CS/AN7 bit2 ST/TTL(1) Input/output port pin or chip select control input in parallel slave port mode or analog input: CS 1 = Device is not selected 0 = Device is selected Legend: ST = Schmitt Trigger input TTL = TTL input Note 1: Input buffers are Schmitt Triggers when in I/O mode and TTL buffers when in Parallel Slave Port Mode. TABLE 3-10: Addr Name SUMMARY OF REGISTERS ASSOCIATED WITH PORTE Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 09h PORTE -- -- -- -- -- 89h TRISE IBF OBF IBOV PSPMODE -- 9Fh ADCON1 ADFM -- -- -- PCFG3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR RE2 RE1 RE0 ---- -xxx ---- -uuu PORTE Data Direction Bits 0000 -111 0000 -111 --0- 0000 --0- 0000 PCFG2 PCFG1 PCFG0 Value on all other resets Legend: x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by PORTE. 1999 Microchip Technology Inc. Preliminary DS30569A-page 35 PIC16F870/871 3.6 Parallel Slave Port FIGURE 3-8: PORTD AND PORTE BLOCK DIAGRAM (PARALLEL SLAVE PORT) The Parallel Slave Port is not implemented on the PIC16F870. PORTD operates as an 8-bit wide Parallel Slave Port or microprocessor port when control bit PSPMODE (TRISE<4>) is set. In slave mode, it is asynchronously readable and writable by the external world through RD control input pin RE0/RD and WR control input pin RE1/WR. It can directly interface to an 8-bit microprocessor data bus. The external microprocessor can read or write the PORTD latch as an 8-bit latch. Setting bit PSPMODE enables port pin RE0/RD to be the RD input, RE1/WR to be the WR input and RE2/CS to be the CS (chip select) input. For this functionality, the corresponding data direction bits of the TRISE register (TRISE<2:0>) must be configured as inputs (set). The A/D port configuration bits PCFG3:PCFG0 (ADCON1<3:0>) must be set to configure pins RE2:RE0 as digital I/O. Data Bus D WR PORT RDx pin CK TTL Q RD PORT D ENEN One bit of PORTD Set interrupt flag PSPIF (PIR1<7>) There are actually two 8-bit latches. One for data-out and one for data input. The user writes 8-bit data to the PORTD data latch and reads data from the port pin latch (note that they have the same address). In this mode, the TRISD register is ignored, since the microprocessor is controlling the direction of data flow. A write to the PSP occurs when both the CS and WR lines are first detected low. When either the CS or WR lines become high (level triggered), the Input Buffer Full (IBF) status flag bit (TRISE<7>) is set on the Q4 clock cycle, following the next Q2 cycle, to signal the write is complete (Figure 3-9). The interrupt flag bit PSPIF (PIR1<7>) is also set on the same Q4 clock cycle. IBF can only be cleared by reading the PORTD input latch. The Input Buffer Overflow (IBOV) status flag bit (TRISE<5>) is set if a second write to the PSP is attempted when the previous byte has not been read out of the buffer. Q Read TTL RD Chip Select TTL CS Write TTL WR Note: I/O pin has protection diodes to VDD and VSS. A read from the PSP occurs when both the CS and RD lines are first detected low. The Output Buffer Full (OBF) status flag bit (TRISE<6>) is cleared immediately (Figure 3-10) indicating that the PORTD latch is waiting to be read by the external bus. When either the CS or RD pin becomes high (level triggered), the interrupt flag bit PSPIF is set on the Q4 clock cycle, following the next Q2 cycle, indicating that the read is complete. OBF remains low until data is written to PORTD by the user firmware. When not in PSP mode, the IBF and OBF bits are held clear. However, if flag bit IBOV was previously set, it must be cleared in firmware. An interrupt is generated and latched into flag bit PSPIF when a read or write operation is completed. PSPIF must be cleared by the user in firmware and the interrupt can be disabled by clearing the interrupt enable bit PSPIE (PIE1<7>). DS30569A-page 36 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 FIGURE 3-9: PARALLEL SLAVE PORT WRITE WAVEFORMS Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q4 Q1 Q2 Q3 Q4 CS WR RD PORTD<7:0> IBF OBF PSPIF FIGURE 3-10: PARALLEL SLAVE PORT READ WAVEFORMS Q1 Q2 Q3 Q4 Q1 Q2 Q3 CS WR RD PORTD<7:0> IBF OBF PSPIF TABLE 3-11: REGISTERS ASSOCIATED WITH PARALLEL SLAVE PORT Address Name Bit 7 Bit 6 08h PORTD 09h PORTE 89h TRISE 0Ch PIR1 8Ch PIE1 PSPIE ADIE 9Fh ADCON1 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR xxxx xxxx uuuu uuuu RE1 RE0 ---- -xxx ---- -uuu Port data latch when written: Port pins when read -- -- IBF -- -- -- OBF IBOV PSPMODE -- PORTE Data Direction Bits 0000 -111 0000 -111 PSPIF ADIF RCIF TXIF -- CCP1IF TMR2IF TMR1IF 0000 0000 0000 0000 RCIE TXIE -- CCP1IE TMR2IE TMR1IE 0000 0000 0000 0000 -- -- PCFG3 PCFG2 --0- 0000 ADFM -- RE2 Value on all other resets PCFG1 PCFG0 --0- 0000 Legend: x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by the Parallel Slave Port. 1999 Microchip Technology Inc. Preliminary DS30569A-page 37 PIC16F870/871 NOTES: DS30569A-page 38 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 4.0 DATA EEPROM AND FLASH PROGRAM MEMORY The Data EEPROM and FLASH Program Memory are readable and writable during normal operation over the entire VDD range. A bulk erase operation may not be issued from user code (which includes removing code protection). The data memory is not directly mapped in the register file space. Instead, it is indirectly addressed through the Special Function Registers (SFR). There are six SFRs used to read and write the program and data EEPROM memory. These registers are: * * * * * * EECON1 EECON2 EEDATA EEDATH EEADR EEADRH 4.1 EEADR The address registers can address up to a maximum of 256 bytes of data EEPROM or up to a maximum of 8K words of program FLASH. However, the PIC16F870/ 871 have 64 bytes of data EEPROM and 2K words of program FLASH. When selecting a program address value, the MSByte of the address is written to the EEADRH register and the LSByte is written to the EEADR register. When selecting a data address value, only the LSByte of the address is written to the EEADR register. The EEPROM data memory allows byte read and write. When interfacing to the data memory block, EEDATA holds the 8-bit data for read/write and EEADR holds the address of the EEPROM location being accessed. The registers EEDATH and EEADRH are not used for data EEPROM access. The PIC16F870/871 devices have 64 bytes of data EEPROM with an address range from 0h to 3Fh. The EEPROM data memory is rated for high erase/ write cycles. The write time is controlled by an on-chip timer. The write time will vary with voltage and temperature, as well as from chip-to-chip. Please refer to the specifications for exact limits. The program memory allows word reads and writes. Program memory access allows for checksum calculation and calibration table storage. A byte or word write automatically erases the location and writes the new data (erase before write). Writing to program memory will cease operation until the write is complete. The program memory cannot be accessed during the write, therefore code cannot execute. During the write operation, the oscillator continues to clock the peripherals, and therefore, they continue to operate. Interrupt events will be detected and essentially "queued" until the write is completed. When the write completes, the next instruction in the pipeline is executed and the branch to the interrupt vector address will occur. When interfacing to the program memory block, the EEDATH:EEDATA registers form a two byte word, which holds the 14-bit data for read/write. The EEADRH:EEADR registers form a two byte word, which holds the 13-bit address of the FLASH location being accessed. The PIC16F870/871 devices have 2K words of program FLASH with an address range from 0h to 7FFh. The unused upper bits in both the EEDATH and EEDATA registers all read as "0's". 1999 Microchip Technology Inc. The value written to program memory does not need to be a valid instruction. Therefore, up to 14-bit numbers can be stored in memory for use as calibration parameters, serial numbers, packed 7-bit ASCII, etc. Executing a program memory location containing data that forms an invalid instruction results in a NOP. On the PIC16F870/871 devices, the upper two bits of the EEADR must always be cleared to prevent inadvertent access to the wrong location in data EEPROM. This also applies to the program memory. The upper five MSbits of EEADRH must always be clear during program FLASH access. 4.2 EECON1 and EECON2 Registers EECON1 is the control register for memory accesses. EECON2 is not a physical register. Reading EECON2 will read all '0's. The EECON2 register is used exclusively in the memory write sequence. Control bit EEPGD determines if the access will be a program or a data memory access. When clear, any subsequent operations will operate on the data memory. When set, any subsequent operations will operate on the program memory. Control bits RD and WR initiate read and write operations, respectively. These bits cannot be cleared, only set, in software. They are cleared in hardware at the completion of the read or write operation. The inability to clear the WR bit in software prevents the accidental or premature termination of a write operation. The WREN bit, when set, will allow a write operation. On power-up, the WREN bit is clear. The WRERR bit is set when a write operation is interrupted by a MCLR reset or a WDT time-out reset during normal operation. In these situations, following reset, the user can check the WRERR bit and rewrite the location. The value of the data and address registers and the EEPGD bit remains unchanged. Interrupt flag bit EEIF, in the PIR2 register, is set when write is complete. It must be cleared in software. Preliminary DS30569A-page 39 PIC16F870/871 REGISTER 4-1: EECON1 REGISTER (ADDRESS 18Ch) R/W-x U-0 U-0 U-0 R/W-x R/W-0 R/W-0 R/W-0 EEPGD -- -- -- WRERR WREN WR RD bit7 bit 7: bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n= Value at POR reset EEPGD: Program / Data EEPROM Select bit 1 = Accesses Program memory 0 = Accesses data memory (This bit cannot be changed while a read or write operation is in progress) bit 6-4: Unimplemented: Read as '0' bit 3: WRERR: EEPROM Error Flag bit 1 = A write operation is prematurely terminated (any MCLR reset or any WDT reset during normal operation) 0 = The write operation completed bit 2: WREN: EEPROM Write Enable bit 1 = Allows write cycles 0 = Inhibits write to the EEPROM bit 1: WR: Write Control bit 1 = Initiates a write cycle. (The bit is cleared by hardware once write is complete.) The WR bit can only be set (not cleared) in software. 0 = Write cycle to the EEPROM is complete bit 0: RD: Read Control bit 1 = Initiates an EEPROM read RD is cleared in hardware. The RD bit can only be set (not cleared) in software. 0 = Does not initiate an EEPROM read DS30569A-page 40 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 4.3 Reading the Data EEPROM Memory To read a data memory location, the user must write the address to the EEADR register, clear the EEPGD control bit (EECON1<7>) and then set control bit RD (EECON1<0>). The data is available in the very next instruction cycle of the EEDATA register, therefore it can be read by the next instruction. EEDATA will hold this value until another read operation or until it is written to by the user (during a write operation). 4.4 EXAMPLE 4-1: DATA EEPROM READ BSF STATUS, RP1 ; BCF STATUS, RP0 ;Bank 2 MOVLW DATA_EE_ADDR ; MOVWF EEADR ;Data Memory Address to read BSF STATUS, RP0 ;Bank 3 BCF EECON1, EEPGD ;Point to DATA memory BSF EECON1, RD ;EEPROM Read BCF STATUS, RP0 ;Bank 2 MOVF EEDATA, W ;W = EEDATA Writing to the Data EEPROM Memory To write an EEPROM data location, the address must first be written to the EEADR register and the data written to the EEDATA register. Then the sequence in Example 4-2 must be followed to initiate the write cycle. EXAMPLE 4-2: DATA EEPROM WRITE BSF STATUS, RP1 ; BCF STATUS, RP0 ; Bank 2 MOVLW DATA_EE_ADDR ; MOVWF EEADR ; Data Memory Address to write MOVLW DATA_EE_DATA ; MOVWF EEDATA ; Data Memory Value to write BSF STATUS, RP0 ; Bank 3 BCF EECON1, EEPGD ; Point to DATA memory BSF EECON1, WREN ; Enable writes BCF INTCON, GIE ; Disable Interrupts MOVLW 55h ; Required MOVWF EECON2 ; Write 55h Sequence MOVLW AAh ; MOVWF EECON2 ; Write AAh BSF EECON1, WR ; Set WR bit to begin write BSF INTCON, GIE ; Enable Interrupts SLEEP BCF ; Wait for interrupt to signal write complete EECON1, WREN ; Disable writes The write will not initiate if the above sequence is not exactly followed (write 55h to EECON2, write AAh to EECON2, then set WR bit) for each byte. It is strongly recommended that interrupts be disabled during this code segment. Additionally, the WREN bit in EECON1 must be set to enable writes. This mechanism prevents accidental writes to data EEPROM due to unexpected code execution (i.e., runaway programs). The WREN bit should be kept clear at all times, except when updating the EEPROM. The WREN bit is not cleared by hardware is set. The WREN bit must be set on a previous instruction. Both WR and WREN cannot be set with the same instruction. At the completion of the write cycle, the WR bit is cleared in hardware and the EEPROM Write Complete Interrupt Flag bit (EEIF) is set. EEIF must be cleared by software. After a write sequence has been initiated, clearing the WREN bit will not affect the current write cycle. The WR bit will be inhibited from being set unless the WREN bit 1999 Microchip Technology Inc. Preliminary DS30569A-page 41 PIC16F870/871 4.5 Reading the FLASH Program Memory A program memory location may be read by writing two bytes of the address to the EEADR and EEADRH registers, setting the EEPGD control bit (EECON1<7>) and then setting control bit RD (EECON1<0>). Once the read control bit is set, the microcontroller will use the next two instruction cycles to read the data. The EXAMPLE 4-3: Required data is available in the EEDATA and EEDATH registers after the second NOP instruction. Therefore, it can be read as two bytes in the following instructions. The EEDATA and EEDATH registers will hold this value until another read operation or until it is written to by the user (during a write operation). FLASH PROGRAM READ BSF STATUS, RP1 ; BCF STATUS, RP0 ; Bank 2 MOVLW ADDRH ; MOVWF EEADRH ; MSByte of Program Address to read MOVLW ADDRL ; MOVWF EEADR ; LSByte of Program Address to read BSF STATUS, RP0 ; Bank 3 BSF EECON1, EEPGD ; Point to PROGRAM memory BSF EECON1, RD ; EEPROM Read Sequence NOP ; memory is read in the next two cycles after BSF EECON1,RD NOP DS30569A-page 42 ; BCF STATUS, RP0 ; Bank 2 MOVF EEDATA, W ; W = LSByte of Program EEDATA MOVF EEDATH, W ; W = MSByte of Program EEDATA Preliminary 1999 Microchip Technology Inc. PIC16F870/871 4.6 trol bit (EECON1<7>), and then set control bit WR (EECON1<1>). The sequence in Example 4-4 must be followed to initiate a write to program memory. Writing to the FLASH Program Memory When the PIC16F870/871 are fully code protected or not code protected, a word of the FLASH program memory may be written provided the WRT configuration bit is set. If the PIC16F870/871 are partially code protected, then a word of FLASH program memory may be written if the word is in a non-code protected segment of memory and the WRT configuration bit is set. To write a FLASH program location, the first two bytes of the address must be written to the EEADR and EEADRH registers and two bytes of the data to the EEDATA and EEDATH registers, set the EEPGD con- EXAMPLE 4-4: The microcontroller will then halt internal operations during the next two instruction cycles for the TPEW (parameter D133) in which the write takes place. This is not SLEEP mode, as the clocks and peripherals will continue to run. Therefore, the two instructions following the "BSF EECON, WR" should be NOP instructions. After the write cycle, the microcontroller will resume operation with the 3rd instruction after the EECON1 write instruction. FLASH PROGRAM WRITE BSF STATUS, RP1 ; BCF STATUS, RP0 ; Bank 2 MOVLW ADDRH ; MOVWF EEADRH ; MSByte of Program Address to read MOVLW ADDRL ; MOVWF EEADR ; LSByte of Program Address to read MOVLW DATAH ; MOVWF EEDATH ; MS Program Memory Value to write MOVLW DATAL ; MOVWF EEDATA ; LS Program Memory Value to write BSF STATUS, RP0 ; Bank 3 BSF EECON1, EEPGD ; Point to PROGRAM memory BSF EECON1, WREN ; Enable writes BCF INTCON, GIE ; Disable Interrupts MOVLW 55h ; Required MOVWF EECON2 ; Write 55h Sequence MOVLW AAh ; MOVWF EECON2 ; Write AAh BSF EECON1, WR ; Set WR bit to begin write NOP ; Instructions here are ignored by the microcontroller NOP ; Microcontroller will halt operation and wait for ; a write complete. After the write ; the microcontroller continues with 3rd instruction BSF INTCON, BCF EECON1, WREN 1999 Microchip Technology Inc. GIE ; Enable Interrupts ; Disable writes Preliminary DS30569A-page 43 PIC16F870/871 4.7 Write Verify 4.9 Depending on the application, good programming practice may dictate that the value written to the memory should be verified against the original value. This should be used in applications where excessive writes can stress bits near the specification limit. Generally a write failure will be a bit which was written as a '1', but reads back as a '0' (due to leakage off the bit). 4.8 Protection Against Spurious Write 4.8.1 EEPROM DATA MEMORY There are conditions when the device may not want to write to the data EEPROM memory. To protect against spurious EEPROM writes, various mechanisms have been built-in. On power-up, the WREN bit is cleared. Also, the Power-up Timer (72 ms duration) prevents EEPROM write. The write initiate sequence and the WREN bit together help prevent an accidental write during brown-out, power glitch, or software malfunction. 4.8.2 PROGRAM FLASH MEMORY To protect against spurious writes to FLASH program memory, the WRT bit in the configuration word may be programmed to `0' to prevent writes. The write initiate sequence must also be followed. WRT and the configuration word cannot be programmed by user code, only through the use of an external programmer. TABLE 4-1: Operation during Code Protect Each reprogrammable memory block has its own code protect mechanism. External Read and Write operations are disabled if either of these mechanisms are enabled. 4.9.1 DATA EEPROM MEMORY The microcontroller itself can both read and write to the internal Data EEPROM, regardless of the state of the code protect configuration bit. When data memory is code protected (CONFIG<8>=0) any further external programming access of program memory is disabled. To reenable programming access to program memory, both bulk erase and removal of code protection must be performed on program and data memory. 4.9.2 PROGRAM FLASH MEMORY The microcontroller can read and execute instructions out of the internal FLASH program memory, regardless of the state of the code protect configuration bits. However, the WRT configuration bit and the code protect bits have different effects on writing to program memory. Table 4-1 shows the various configurations and status of reads and writes. To erase the WRT or code protection bits in the configuration word requires that the device be fully erased. READ/WRITE STATE OF INTERNAL FLASH PROGRAM MEMORY Configuration Bits Memory Location CP1 CP0 WRT 0 0 1 1 0 0 1 1 1 0 0 1 DS30569A-page 44 Internal Read Internal Write Yes Yes Yes Yes Yes No No Yes All program memory All program memory All program memory All program memory Preliminary ICSP Read ICSP Write No No Yes Yes No No Yes Yes 1999 Microchip Technology Inc. PIC16F870/871 TABLE 4-2: Address REGISTERS ASSOCIATED WITH DATA EEPROM/PROGRAM FLASH Name 0Bh, 8Bh, INTCON 10Bh, 18Bh 10Dh EEADR 10Fh EEADRH Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR Value on all other resets GIE PEIE T0IE INTE RBIE T0IF INTF RBIF 0000 000x 0000 000u xxxx xxxx uuuu uuuu -- -- xxxx xxxx uuuu uuuu xxxx xxxx uuuu uuuu xxxx xxxx uuuu uuuu EEPROM address register -- -- -- 10Ch EEDATA 10Eh EEDATH -- -- 18Ch EECON1 EEPGD -- 18Dh EECON2 8Dh PIE2 -- -- -- EEIE 0Dh PIR2 -- -- -- EEIF Legend: EEPROM address high EEPROM data resister EEPROM data resister high -- -- WREN WR RD x--- x000 x--- u000 -- -- -- -- ---0 ---- ---0 ---- -- -- -- -- ---0 ---- ---0 ---- WRERR EEPROM control resister2 (not a physical resister) x = unknown, u = unchanged, r = reserved, - = unimplemented read as '0'. Shaded cells are not used by the Timer1 module. 1999 Microchip Technology Inc. Preliminary DS30569A-page 45 PIC16F870/871 NOTES: DS30569A-page 46 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 5.0 TIMER0 MODULE Counter mode is selected by setting bit T0CS (OPTION_REG<5>). In counter mode, Timer0 will increment either on every rising or falling edge of pin RA4/T0CKI. The incrementing edge is determined by the Timer0 Source Edge Select bit T0SE (OPTION_REG<4>). Clearing bit T0SE selects the rising edge. Restrictions on the external clock input are discussed in detail in Section 5.2. The Timer0 module timer/counter has the following features: * * * * * * 8-bit timer/counter Readable and writable 8-bit software programmable prescaler Internal or external clock select Interrupt on overflow from FFh to 00h Edge select for external clock The prescaler is mutually exclusively shared between the Timer0 module and the watchdog timer. The prescaler is not readable or writable. Section 5.3 details the operation of the prescaler. Figure 5-1 is a block diagram of the Timer0 module and the prescaler shared with the WDT. 5.1 Additional information on the Timer0 module is available in the PICmicroTM Mid-Range MCU Family Reference Manual (DS33023). The TMR0 interrupt is generated when the TMR0 register overflows from FFh to 00h. This overflow sets bit T0IF (INTCON<2>). The interrupt can be masked by clearing bit T0IE (INTCON<5>). Bit T0IF must be cleared in software by the Timer0 module interrupt service routine before re-enabling this interrupt. The TMR0 interrupt cannot awaken the processor from SLEEP since the timer is shut off during SLEEP. Timer mode is selected by clearing bit T0CS (OPTION_REG<5>). In timer mode, the Timer0 module will increment every instruction cycle (without prescaler). If the TMR0 register is written, the increment is inhibited for the following two instruction cycles. The user can work around this by writing an adjusted value to the TMR0 register. FIGURE 5-1: Timer0 Interrupt BLOCK DIAGRAM OF THE TIMER0/WDT PRESCALER Data Bus CLKOUT (= FOSC/4) 0 RA4/T0CKI Pin 8 M U X 1 M U X 0 1 SYNC 2 Cycles TMR0 reg T0SE T0CS Set Flag Bit T0IF on Overflow PSA PRESCALER 0 Watchdog Timer M U X 1 8-bit Prescaler 8 8 - to - 1MUX PS2:PS0 PSA WDT Enable bit 1 0 MUX PSA WDT Time-out Note: T0CS, T0SE, PSA, PS2:PS0 are (OPTION_REG<5:0>). 1999 Microchip Technology Inc. Preliminary DS30569A-page 47 PIC16F870/871 5.2 Using Timer0 with an External Clock module means that there is no prescaler for the watchdog timer, and vice-versa. This prescaler is not readable or writable (see Figure 5-1). When no prescaler is used, the external clock input is the same as the prescaler output. The synchronization of T0CKI with the internal phase clocks is accomplished by sampling the prescaler output on the Q2 and Q4 cycles of the internal phase clocks. Therefore, it is necessary for T0CKI to be high for at least 2Tosc (and a small RC delay of 20 ns) and low for at least 2Tosc (and a small RC delay of 20 ns). Refer to the electrical specification of the desired device. 5.3 The PSA and PS2:PS0 bits (OPTION_REG<3:0>) determine the prescaler assignment and prescale ratio. When assigned to the Timer0 module, all instructions writing to the TMR0 register (e.g. CLRF 1, MOVWF 1, BSF 1,x....etc.) will clear the prescaler. When assigned to WDT, a CLRWDT instruction will clear the prescaler along with the Watchdog Timer. The prescaler is not readable or writable. Prescaler Note: There is only one prescaler available, which is mutually exclusively shared between the Timer0 module and the watchdog timer. A prescaler assignment for the Timer0 Writing to TMR0, when the prescaler is assigned to Timer0, will clear the prescaler count, but will not change the prescaler assignment. REGISTER 5-1: OPTION_REG REGISTER R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 RBPU INTEDG T0CS T0SE PSA PS2 PS1 PS0 bit 7 bit 0 bit 7: RBPU bit 6: INTEDG bit 5: T0CS: TMR0 Clock Source Select bit 1 = Transition on T0CKI pin 0 = Internal instruction cycle clock (CLKOUT) bit 4: T0SE: TMR0 Source Edge Select bit 1 = Increment on high-to-low transition on T0CKI pin 0 = Increment on low-to-high transition on T0CKI pin bit 3: PSA: Prescaler Assignment bit 1 = Prescaler is assigned to the WDT 0 = Prescaler is assigned to the Timer0 module R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset bit 2-0: PS2:PS0: Prescaler Rate Select bits Note: Bit Value TMR0 Rate WDT Rate 000 001 010 011 100 101 110 111 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128 1 : 256 1:1 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128 To avoid an unintended device RESET, the instruction sequence shown in the PICmicroTM Mid-Range MCU Family Reference Manual (DS33023) must be executed when changing the prescaler assignment from Timer0 to the WDT. This sequence must be followed even if the WDT is disabled. DS30569A-page 48 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 TABLE 5-1: Address REGISTERS ASSOCIATED WITH TIMER0 Name Bit 7 Bit 6 01h,101h TMR0 0Bh,8Bh, 10Bh,18Bh INTCON 81h,181h OPTION_REG RBPU INTEDG Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Timer0 module's register GIE PEIE Value on: POR, BOR Value on all other resets xxxx xxxx uuuu uuuu T0IE INTE RBIE T0IF INTF RBIF 0000 000x 0000 000u T0CS T0SE PSA PS2 PS1 PS0 1111 1111 1111 1111 Legend: x = unknown, u = unchanged, - = unimplemented locations read as '0'. Shaded cells are not used by Timer0. 1999 Microchip Technology Inc. Preliminary DS30569A-page 49 PIC16F870/871 NOTES: DS30569A-page 50 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 6.0 TIMER1 MODULE In timer mode, Timer1 increments every instruction cycle. In counter mode, it increments on every rising edge of the external clock input. The Timer1 module is a 16-bit timer/counter consisting of two 8-bit registers (TMR1H and TMR1L), which are readable and writable. The TMR1 Register pair (TMR1H:TMR1L) increments from 0000h to FFFFh and rolls over to 0000h. The TMR1 Interrupt, if enabled, is generated on overflow, which is latched in interrupt flag bit TMR1IF (PIR1<0>). This interrupt can be enabled/disabled by setting/clearing TMR1 interrupt enable bit TMR1IE (PIE1<0>). Timer1 can be enabled/disabled by setting/clearing control bit TMR1ON (T1CON<0>). Timer1 also has an internal "reset input". This reset can be generated by the CCP module (Section 8.0). Register 6-1 shows the Timer1 control register. When the Timer1 oscillator is enabled (T1OSCEN is set), the RC1/T1OSI and RC0/T1OSO/T1CKI pins become inputs. That is, the TRISC<1:0> value is ignored. Timer1 can operate in one of two modes: * As a timer * As a counter Additional information on timer modules is available in the PICmicroTM Mid-range MCU Family Reference Manual (DS33023). The operating mode is determined by the clock select bit, TMR1CS (T1CON<1>). REGISTER 6-1: T1CON: TIMER1 CONTROL REGISTER (ADDRESS 10h) U-0 -- bit7 U-0 -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset bit 7-6: Unimplemented: Read as '0' bit 5-4: T1CKPS<1:0>: Timer1 Input Clock Prescale Select bits 11 = 1:8 Prescale value 10 = 1:4 Prescale value 01 = 1:2 Prescale value 00 = 1:1 Prescale value bit 3: bit 2: T1OSCEN: Timer1 Oscillator Enable Control bit 1 = Oscillator is enabled 0 = Oscillator is shut off (The oscillator inverter is turned off to eliminate power drain) T1SYNC: Timer1 External Clock Input Synchronization Control bit TMR1CS = 1 1 = Do not synchronize external clock input 0 = Synchronize external clock input TMR1CS = 0 This bit is ignored. Timer1 uses the internal clock when TMR1CS = 0. bit 1: TMR1CS: Timer1 Clock Source Select bit 1 = External clock from pin RC0/T1OSO/T1CKI (on the rising edge) 0 = Internal clock (FOSC/4) bit 0: TMR1ON: Timer1 On bit 1 = Enables Timer1 0 = Stops Timer1 1999 Microchip Technology Inc. Preliminary DS30569A-page 51 PIC16F870/871 6.1 Timer1 Operation in Timer Mode 6.2 Timer mode is selected by clearing the TMR1CS (T1CON<1>) bit. In this mode, the input clock to the timer is FOSC/4. The synchronize control bit T1SYNC (T1CON<2>) has no effect since the internal clock is always in sync. FIGURE 6-1: Timer1 Counter Operation Timer1 may operate in asynchronous or usynchronous mode depending on the setting of the TMR1CS bit. When Timer1 is being incremented via an external source, increments occur on a rising edge. After Timer1 is enabled in counter mode, the module must first have a falling edge before the counter begins to increment. TIMER1 INCREMENTING EDGE T1CKI (Default high) T1CKI (Default low) Note: Arrows indicate counter increments. 6.3 If T1SYNC is cleared, then the external clock input is synchronized with internal phase clocks. The synchronization is done after the prescaler stage. The prescaler stage is an asynchronous ripple-counter. Timer1 Operation in Synchronized Counter Mode Counter mode is selected by setting bit TMR1CS. In this mode, the timer increments on every rising edge of clock input on pin RC1/T1OSI, when bit T1OSCEN is set, or on pin RC0/T1OSO/T1CKI, when bit T1OSCEN is cleared. FIGURE 6-2: In this configuration, during SLEEP mode, Timer1 will not increment even if the external clock is present, since the synchronization circuit is shut off. The prescaler however will continue to increment. TIMER1 BLOCK DIAGRAM Set flag bit TMR1IF on Overflow 0 TMR1 TMR1H Synchronized clock input TMR1L 1 TMR1ON on/off T1OSC RC0/T1OSO/T1CKI RC1/T1OSI(2) T1SYNC (2) 1 T1OSCEN FOSC/4 Enable Internal Oscillator(1) Clock Synchronize Prescaler 1, 2, 4, 8 det 0 2 T1CKPS<1:0> Q Clock TMR1CS Note 1: When the T1OSCEN bit is cleared, the inverter is turned off. This eliminates power drain. 2: For the PIC16F870/871, the Schmitt Trigger is not implemented in external clock mode. DS30569A-page 52 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 6.4 Timer1 Operation in Asynchronous Counter Mode If control bit T1SYNC (T1CON<2>) is set, the external clock input is not synchronized. The timer continues to increment asynchronous to the internal phase clocks. The timer will continue to run during SLEEP and can generate an interrupt on overflow, which will wake-up the processor. However, special precautions in software are needed to read/write the timer (Section 6.4.1). In asynchronous counter mode, Timer1 can not be used as a time-base for capture or compare operations. 6.4.1 READING AND WRITING TIMER1 IN ASYNCHRONOUS COUNTER MODE Reading TMR1H or TMR1L while the timer is running from an external asynchronous clock will guarantee a valid read (taken care of in hardware). However, the user should keep in mind that reading the 16-bit timer in two 8-bit values itself poses certain problems, since the timer may overflow between the reads. For writes, it is recommended that the user simply stop the timer and write the desired values. A write contention may occur by writing to the timer registers, while the register is incrementing. This may produce an unpredictable value in the timer register. Reading the 16-bit value requires some care. Examples 12-2 and 12-3 in the PICmicroTM Mid-Range MCU Family Reference Manual (DS33023) show how to read and write Timer1 when it is running in asynchronous mode. 6.5 Timer1 Oscillator A crystal oscillator circuit is built-in between pins T1OSI (input) and T1OSO (amplifier output). It is enabled by setting control bit T1OSCEN (T1CON<3>). The oscillator is a low power oscillator rated up to 200 kHz. It will continue to run during SLEEP. It is primarily intended for use with a 32 kHz crystal. Table 6-1 shows the capacitor selection for the Timer1 oscillator. The Timer1 oscillator is identical to the LP oscillator. The user must provide a software time delay to ensure proper oscillator start-up. TABLE 6-1: CAPACITOR SELECTION FOR THE TIMER1 OSCILLATOR Osc Type Freq C1 C2 LP 32 kHz 100 kHz 200 kHz 33 pF 15 pF 15 pF 33 pF 15 pF 15 pF These values are for design guidance only. Crystals Tested: 32.768 kHz 100 kHz 200 kHz Epson C-001R32.768K-A Epson C-2 100.00 KC-P STD XTL 200.000 kHz 20 PPM 20 PPM 20 PPM Note 1: Higher capacitance increases the stability of oscillator, but also increases the start-up time. 2: Since each resonator/crystal has its own characteristics, the user should consult the resonator/ crystal manufacturer for appropriate values of external components. 6.6 Resetting Timer1 using CCP1 Trigger Output If the CCP1 module is configured in compare mode to generate a "special event trigger" (CCP1M<3:0> = 1011), this signal will reset Timer1. Note: The special event trigger from the CCP1 module will not set interrupt flag bit TMR1IF (PIR1<0>). Timer1 must be configured for either timer or synchronized counter mode to take advantage of this feature. If Timer1 is running in asynchronous counter mode, this reset operation may not work. In the event that a write to Timer1 coincides with a special event trigger from CCP1, the write will take precedence. In this mode of operation, the CCPR1H:CCPR1L register pair effectively becomes the period register for Timer1. 6.7 Resetting of Timer1 Register Pair (TMR1H, TMR1L) TMR1H and TMR1L registers are not reset to 00h on a POR or any other reset except by the CCP1 special event trigger. T1CON register is reset to 00h on a Power-on Reset or a Brown-out Reset, which shuts off the timer and leaves a 1:1 prescale. In all other resets, the register is unaffected. 6.8 Timer1 Prescaler The prescaler counter is cleared on writes to the TMR1H or TMR1L registers. 1999 Microchip Technology Inc. Preliminary DS30569A-page 53 PIC16F870/871 TABLE 6-2: Address REGISTERS ASSOCIATED WITH TIMER1 AS A TIMER/COUNTER Name 0Bh,8Bh, INTCON 10Bh, 18Bh Value on: POR, BOR Value on all other resets Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 GIE PEIE T0IE INTE RBIE T0IF INTF RBIF 0000 000x 0000 000u PIR1 PSPIF(1) ADIF RCIF TXIF -- CCP1IF TMR2IF TMR1IF 0000 -000 0000 -000 8Ch PIE1 (1) PSPIE ADIE RCIE TXIE -- CCP1IE TMR2IE TMR1IE 0000 -000 0000 -000 0Eh TMR1L Holding register for the Least Significant Byte of the 16-bit TMR1 register xxxx xxxx uuuu uuuu 0Fh TMR1H Holding register for the Most Significant Byte of the 16-bit TMR1 register xxxx xxxx uuuu uuuu 10h T1CON 0Ch -- -- T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON --00 0000 --uu uuuu Legend: x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by the Timer1 module. Note 1: Bits PSPIE and PSPIF are reserved on the PIC16F870; always maintain these bits clear. DS30569A-page 54 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 7.0 TIMER2 MODULE 7.1 Timer2 is an 8-bit timer with a prescaler and a postscaler. It can be used as the PWM time-base for the PWM mode of the CCP module(s). The TMR2 register is readable and writable, and is cleared on any device reset. The input clock (FOSC/4) has a prescale option of 1:1, 1:4 or 1:16, selected by control bits T2CKPS1:T2CKPS0 (T2CON<1:0>). The Timer2 module has an 8-bit period register PR2. Timer2 increments from 00h until it matches PR2 and then resets to 00h on the next increment cycle. PR2 is a readable and writable register. The PR2 register is initialized to FFh upon reset. The match output of TMR2 goes through a 4-bit postscaler (which gives a 1:1 to 1:16 scaling inclusive) to generate a TMR2 interrupt (latched in flag bit TMR2IF, (PIR1<1>)). Timer2 Prescaler and Postscaler The prescaler and postscaler counters are cleared when any of the following occurs: * a write to the TMR2 register * a write to the T2CON register * any device reset (POR, MCLR reset, WDT reset or BOR) TMR2 is not cleared when T2CON is written. 7.2 Output of TMR2 The output of TMR2 (before the postscaler) is fed to the SSPort module, which optionally uses it to generate shift clock. FIGURE 7-1: TIMER2 BLOCK DIAGRAM Sets flag bit TMR2IF Timer2 can be shut off by clearing control bit TMR2ON (T2CON<2>) to minimize power consumption. TMR2 reg Register 7-1 shows the Timer2 control register. Postscaler 1:1 to 1:16 Additional information on timer modules is available in the PICmicroTM Mid-Range MCU Family Reference Manual (DS33023). EQ Comparator 4 PR2 reg Prescaler 1:1, 1:4, 1:16 FOSC/4 2 T2CKPS1: T2CKPS0 T2OUTPS3: T2OUTPS0 REGISTER 7-1: T2CON: TIMER2 CONTROL REGISTER (ADDRESS 12h) U-0 -- R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON R/W-0 R/W-0 T2CKPS1 T2CKPS0 bit7 bit0 bit 7: Unimplemented: Read as '0' bit 6-3: TOUTPS3:TOUTPS0: Timer2 Output Postscale Select bits 0000 = 1:1 Postscale 0001 = 1:2 Postscale 0010 = 1:3 Postscale * * * 1111 = 1:16 Postscale bit 2: TMR2ON: Timer2 On bit 1 = Timer2 is on 0 = Timer2 is off bit 1-0: T2CKPS1:T2CKPS0: Timer2 Clock Prescale Select bits 00 = Prescaler is 1 01 = Prescaler is 4 1x = Prescaler is 16 1999 Microchip Technology Inc. Preliminary R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset DS30569A-page 55 PIC16F870/871 TABLE 7-1: Address Name REGISTERS ASSOCIATED WITH TIMER2 AS A TIMER/COUNTER Value on: POR, BOR Value on all other resets Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 GIE PEIE T0IE INTE RBIE T0IF INTF RBIF 0000 000x 0000 000u PIR1 PSPIF(1) ADIF RCIF TXIF -- CCP1IF TMR2IF TMR1IF 0000 -000 0000 -000 8Ch PIE1 PSPIE(1) ADIE RCIE TXIE -- CCP1IE TMR2IE TMR1IE 0000 -000 0000 -000 11h TMR2 12h T2CON 92h PR2 0Bh,8Bh, INTCON 10Bh,18Bh 0Ch Legend: Note 1: 0000 0000 0000 0000 Timer2 module's register -- TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 -000 0000 1111 1111 1111 1111 Timer2 Period Register x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by the Timer2 module. Bits PSPIE and PSPIF are reserved on the PIC16F870; always maintain these bits clear. DS30569A-page 56 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 8.0 CAPTURE/COMPARE/PWM MODULE the operation of CCP1. The special event trigger is generated by a compare match and will reset Timer1 and start an A/D conversion (if the A/D module is enabled). The Capture/Compare/PWM (CCP) module contains a 16-bit register which can operate as a: * 16-bit Capture register * 16-bit Compare register * PWM master/slave Duty Cycle register Additional information on CCP modules is available in the PICmicroTM Mid-Range MCU Family Reference Manual (DS33023) and in Application Note 594, "Using the CCP Modules" (DS00594). TABLE 8-1: Table 8-1 shows the resources used by the CCP module. In the following sections, the operation of a CCP module is described. CCP1 Module: Capture/Compare/PWM Register1 (CCPR1) is comprised of two 8-bit registers: CCPR1L (low byte) and CCPR1H (high byte). The CCP1CON register controls CCP MODE - TIMER RESOURCES REQUIRED CCP Mode Timer Resource Capture Compare PWM Timer1 Timer1 Timer2 REGISTER 8-1: CCP1CON REGISTER (ADDRESS: 17h) U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 -- -- CCP1X CCP1Y CCP1M3 CCP1M2 CCP1M1 CCP1M0 bit7 bit0 R =Readable bit W =Writable bit U =Unimplemented bit, read as `0' - n =Value at POR reset bit 7-6: Unimplemented: Read as '0' bit 5-4: CCP1<X:Y>: PWM Least Significant bits Capture Mode: Unused Compare Mode: Unused PWM Mode: These bits are the two LSbs of the PWM duty cycle. The eight MSbs are found in CCPR1L. bit 3-0: CCP1M<3:0>: CCPx Mode Select bits 0000 = Capture/Compare/PWM off (resets CCP module) 0100 = Capture mode, every falling edge 0101 = Capture mode, every rising edge 0110 = Capture mode, every 4th rising edge 0111 = Capture mode, every 16th rising edge 1000 = Compare mode, set output on match (CCP1IF bit is set) 1001 = Compare mode, clear output on match (CCP1IF bit is set) 1010 = Compare mode, generate software interrupt on match (CCP1IF bit is set, CCP pin is unaffected) 1011 = Compare mode, trigger special event (CCP1IF bit is set, CCP1 pin is unaffected); CCP1 resets TMR1 and starts an A/D conversion (if A/D module is enabled) 11xx = PWM mode 1999 Microchip Technology Inc. Preliminary DS30569A -page 57 PIC16F870/871 8.1 Capture Mode 8.1.2 In Capture mode, CCPR1H:CCPR1L captures the 16-bit value of the TMR1 register when an event occurs on pin RC2/CCP1. An event is defined as: * * * * Every falling edge Every rising edge Every 4th rising edge Every 16th rising edge 8.1.1 CCP PIN CONFIGURATION In Capture mode, the RC2/CCP1 pin should be configured as an input by setting the TRISC<2> bit. Note: If the RC2/CCP1 pin is configured as an output, a write to the port can cause a capture condition. FIGURE 8-1: CAPTURE MODE OPERATION BLOCK DIAGRAM Prescaler / 1, 4, 16 Set flag bit CCP1IF (PIR1<2>) RC2/CCP1 Pin CCPR1H and edge detect Timer1 must be running in timer mode or synchronized counter mode for the CCP module to use the capture feature. In asynchronous counter mode, the capture operation may not work. 8.1.3 An event is selected by control bits CCP1M<3:0> (CCP1CON<3:0>). When a capture is made, the interrupt request flag bit CCP1IF (PIR1<2>) is set. The interrupt flag must be cleared in software. If another capture occurs before the value in register CCPR1 is read, the old captured value will be lost. SOFTWARE INTERRUPT When the capture mode is changed, a false capture interrupt may be generated. The user should keep bit CCP1IE (PIE1<2>) clear to avoid false interrupts and should clear the flag bit CCP1IF following any such change in operating mode. 8.1.4 CCP PRESCALER There are four prescaler settings, specified by bits CCP1M<3:0>. Whenever the CCP module is turned off, or the CCP module is not in capture mode, the prescaler counter is cleared. Any reset will clear the prescaler counter. Switching from one capture prescaler to another may generate an interrupt. Also, the prescaler counter will not be cleared, therefore, the first capture may be from a non-zero prescaler. Example 8-1 shows the recommended method for switching between capture prescalers. This example also clears the prescaler counter and will not generate the "false" interrupt. EXAMPLE 8-1: CCPR1L Capture Enable TMR1H TIMER1 MODE SELECTION TMR1L CLRF MOVLW MOVWF CCP1CON<3:0> CHANGING BETWEEN CAPTURE PRESCALERS CCP1CON ;Turn CCP module off NEW_CAPT_PS;Load the W reg with ; the new precscaler ; move value and CCP ON CCP1CON ;Load CCP1CON with this ; value Q's DS30569A -page 58 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 8.2 . Compare Mode In Compare mode, the 16-bit CCPR1 register value is constantly compared against the TMR1 register pair value. When a match occurs, the RC2/CCP1 pin is: * Driven high * Driven low * Remains unchanged 8.3 The action on the pin is based on the value of control bits CCP1M<3:0> (CCP1CON<3:0>). At the same time, interrupt flag bit CCP1IF is set. FIGURE 8-2: COMPARE MODE OPERATION BLOCK DIAGRAM Special event trigger will: reset Timer1, but not set interrupt flag bit TMR1IF (PIR1<0>), and set bit GO/DONE (ADCON0<2>). Special Event Trigger Set flag bit CCP1IF (PIR1<2>) CCPR1H CCPR1L Q S Output Logic match RC2/CCP1 R Pin TRISC<2> Output Enable CCP1CON<3:0> Mode Select 8.2.1 The special event trigger from the CCP1 module will not set interrupt flag bit TMR1IF (PIR1<0>). PWM Mode (PWM) In pulse width modulation mode, the CCP1 pin produces up to a 10-bit resolution PWM output. Since the CCP1 pin is multiplexed with the PORTC data latch, the TRISC<2> bit must be cleared to make the CCP1 pin an output. Note: Clearing the CCP1CON register will force the CCP1 PWM output latch to the default low level. This is not the PORTC I/O data latch. Figure 8-3 shows a simplified block diagram of the CCP module in PWM mode. For a step-by-step procedure on how to set up the CCP module for PWM operation, see Section 8.3.3. FIGURE 8-3: TMR1H Duty Cycle Registers TMR1L CCP PIN CONFIGURATION CCPR1H (Slave) Clearing the CCP1CON register will force the RC2/CCP1 compare output latch to the default low level. This is not the data latch. SOFTWARE INTERRUPT MODE Q RC2/CCP1 (Note 1) S TIMER1 MODE SELECTION When Generate Software Interrupt mode is chosen, the CCP1 pin is not affected. The CCPIF bit is set causing a CCP interrupt (if enabled). 8.2.4 R Comparator Timer1 must be running in Timer mode or Synchronized Counter mode if the CCP module is using the compare feature. In Asynchronous Counter mode, the compare operation may not work. 8.2.3 CCP1CON<5:4> CCPR1L TMR2 8.2.2 SIMPLIFIED PWM BLOCK DIAGRAM Comparator The user must configure the RC2/CCP1 pin as an output by clearing the TRISC<2> bit. Note: Note: TRISC<2> Comparator PR2 Clear Timer, CCP1 pin and latch D.C. Note 1: 8-bit timer is concatenated with 2-bit internal Q clock or 2 bits of the prescaler to create 10-bit time-base. SPECIAL EVENT TRIGGER In this mode, an internal hardware trigger is generated, which may be used to initiate an action. The special event trigger output of CCP1 resets the TMR1 register pair and starts an A/D conversion (if the A/D module is enabled). This allows the CCPR1 register to effectively be a 16-bit programmable period register for Timer1. 1999 Microchip Technology Inc. Preliminary DS30569A -page 59 PIC16F870/871 A PWM output (Figure 8-4) has a time-base (period) and a time that the output stays high (duty cycle). The frequency of the PWM is the inverse of the period (1/ period). FIGURE 8-4: PWM OUTPUT The CCPR1H register and a 2-bit internal latch are used to double buffer the PWM duty cycle. This double buffering is essential for glitchless PWM operation. When the CCPR1H and 2-bit latch match TMR2 concatenated with an internal 2-bit Q clock or 2 bits of the TMR2 prescaler, the CCP1 pin is cleared. Maximum PWM resolution (bits) for a given PWM frequency: Period Resolution Duty Cycle = FOSC log FPWM ( log(2) ) bits TMR2 = PR2 Note: TMR2 = Duty Cycle TMR2 = PR2 8.3.3 8.3.1 PR2 = FOSC --1 4 * FPWM * TMR2 Prescale value The following steps should be taken when configuring the CCP module for PWM operation: 1. 2. 3. When TMR2 is equal to PR2, the following three events occur on the next increment cycle: * TMR2 is cleared * The CCP1 pin is set (exception: if PWM duty cycle = 0%, the CCP1 pin will not be set) * The PWM duty cycle is latched from CCPR1L into CCPR1H 8.3.2 SET-UP FOR PWM OPERATION PWM PERIOD The PWM period is specified by writing to the PR2 register. The PWM period can be calculated using the following formula: Note: If the PWM duty cycle value is longer than the PWM period, the CCP1 pin will not be cleared. 4. 5. Set the PWM period by writing to the PR2 register. Set the PWM duty cycle by writing to the CCPR1L register and CCP1CON<5:4> bits. Make the CCP1 pin an output by clearing the TRISC<2> bit. Set the TMR2 prescale value and enable Timer2 by writing to T2CON. Configure the CCP1 module for PWM operation. The Timer2 postscaler (see Section 8.1) is not used in the determination of the PWM frequency. The postscaler could be used to have a servo update rate at a different frequency than the PWM output. PWM DUTY CYCLE The PWM duty cycle is specified by writing to the CCPR1L register and to the CCP1CON<5:4> bits. Up to 10-bit resolution is available. The CCPR1L contains the eight MSbs and the CCP1CON<5:4> contains the two LSbs. This 10-bit value is represented by CCPR1L:CCP1CON<5:4>. The following equation is used to calculate the PWM duty cycle in time: PWM duty cycle = (CCPR1L:CCP1CON<5:4>) * Tosc * (TMR2 prescale value) CCPR1L and CCP1CON<5:4> can be written to at any time, but the duty cycle value is not latched into CCPR1H until after a match between PR2 and TMR2 occurs (i.e., the period is complete). In PWM mode, CCPR1H is a read-only register. DS30569A -page 60 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 TABLE 8-2: Address REGISTERS ASSOCIATED WITH CAPTURE, COMPARE, AND TIMER1 Name Bit 7 0Bh,8Bh, INTCON 10Bh,18Bh Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on all other resets GIE PEIE T0IE INTE RBIE T0IF INTF PIR1 PSPIF(1) ADIF RCIF TXIF -- CCP1IF TMR2IF TMR1IF 0000 -000 0000 -000 8Ch PIE1 PSPIE(1) ADIE RCIE TXIE -- CCP1IE TMR2IE TMR1IE 0000 -000 0000 -000 87h TRISC PORTC Data Direction Register 1111 1111 1111 1111 0Eh TMR1L Holding register for the Least Significant Byte of the 16-bit TMR1 register xxxx xxxx uuuu uuuu 0Fh TMR1H Holding register for the Most Significant Byte of the 16-bit TMR1 register xxxx xxxx uuuu uuuu 0Ch -- -- RBIF Value on: POR, BOR 0000 000x 0000 000u T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON --00 0000 --uu uuuu 10h T1CON 15h CCPR1L Capture/Compare/PWM register1 (LSB) xxxx xxxx uuuu uuuu 16h CCPR1H Capture/Compare/PWM register1 (MSB) xxxx xxxx uuuu uuuu 17h CCP1CON -- -- CCP1X CCP1Y CCP1M3 CCP1M2 CCP1M1 CCP1M0 --00 0000 --00 0000 Legend: x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by Capture and Timer1. Note 1:The PSP is not implemented on the PIC16F870; always maintain these bits clear. TABLE 8-3: Address REGISTERS ASSOCIATED WITH PWM AND TIMER2 Name 0Bh,8Bh, INTCON 10Bh,18Bh Bit 7 Bit 6 GIE PEIE Bit 5 T0IE Bit 4 Bit 3 INTE RBIE Bit 2 T0IF Bit 1 INTF Bit 0 RBIF Value on: POR, BOR Value on all other resets 0000 000x 0000 000u 0Ch PIR1 PSPIF(1) ADIF RCIF TXIF -- CCP1IF TMR2IF TMR1IF 0000 -000 0000 -000 8Ch PIE1 PSPIE(1) ADIE RCIE TXIE -- CCP1IE TMR2IE TMR1IE 0000 -000 0000 -000 87h TRISC PORTC Data Direction Register 1111 1111 1111 1111 11h TMR2 Timer2 module's register 0000 0000 0000 0000 92h PR2 Timer2 module's period register 1111 1111 1111 1111 12h T2CON 15h CCPR1L Capture/Compare/PWM register1 (LSB) 16h CCPR1H Capture/Compare/PWM register1 (MSB) 17h CCP1CON -- TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 -000 0000 -- -- CCP1X CCP1Y xxxx xxxx uuuu uuuu xxxx xxxx uuuu uuuu CCP1M3 CCP1M2 CCP1M1 CCP1M0 --00 0000 --00 0000 Legend: x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by PWM and Timer2. Note 1:Bits PSPIE and PSPIF are reserved on the PIC16F870; always maintain these bits clear. 1999 Microchip Technology Inc. Preliminary DS30569A -page 61 PIC16F870/871 NOTES: DS30569A -page 62 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 9.0 ADDRESSABLE UNIVERSAL SYNCHRONOUS ASYNCHRONOUS RECEIVER TRANSMITTER (USART) The USART can be configured in the following modes: * Asynchronous (full duplex) * Synchronous - Master (half duplex) * Synchronous - Slave (half duplex) Bit SPEN (RCSTA<7>) and bits TRISC<7:6> have to be set in order to configure pins RC6/TX/CK and RC7/RX/DT as the Universal Synchronous Asynchronous Receiver Transmitter. The Universal Synchronous Asynchronous Receiver Transmitter (USART) module is one of the two serial I/O modules. (USART is also known as a Serial Communications Interface or SCI). The USART can be configured as a full duplex asynchronous system that can communicate with peripheral devices such as CRT terminals and personal computers, or it can be configured as a half duplex synchronous system that can communicate with peripheral devices such as A/D or D/A integrated circuits, serial EEPROMs etc. The USART module also has a multi-processor communication capability using 9-bit address detection. REGISTER 9-1: TXSTA: TRANSMIT STATUS AND CONTROL REGISTER (ADDRESS 98h) R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R-1 R/W-0 CSRC TX9 TXEN SYNC -- BRGH TRMT TX9D bit7 bit0 bit 7: CSRC: Clock Source Select bit Asynchronous mode Don't care Synchronous mode 1 = Master mode (Clock generated internally from BRG) 0 = Slave mode (Clock from external source) bit 6: TX9: 9-bit Transmit Enable bit 1 = Selects 9-bit transmission 0 = Selects 8-bit transmission bit 5: TXEN: Transmit Enable bit 1 = Transmit enabled 0 = Transmit disabled Note: SREN/CREN overrides TXEN in SYNC mode. bit 4: SYNC: USART Mode Select bit 1 = Synchronous mode 0 = Asynchronous mode bit 3: Unimplemented: Read as '0' bit 2: BRGH: High Baud Rate Select bit Asynchronous mode 1 = High speed R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset 0 = Low speed Synchronous mode Unused in this mode bit 1: TRMT: Transmit Shift Register Status bit 1 = TSR empty 0 = TSR full bit 0: TX9D: 9th bit of transmit data. Can be parity bit. 1999 Microchip Technology Inc. Preliminary DS30569A-page 63 PIC16F870/871 REGISTER 9-2: RCSTA: RECEIVE STATUS AND CONTROL REGISTER (ADDRESS 18h) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R-0 R-0 R-x SPEN RX9 SREN CREN ADDEN FERR OERR RX9D bit7 bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset bit 7: SPEN: Serial Port Enable bit 1 = Serial port enabled (Configures RC7/RX/DT and RC6/TX/CK pins as serial port pins) 0 = Serial port disabled bit 6: RX9: 9-bit Receive Enable bit 1 = Selects 9-bit reception 0 = Selects 8-bit reception bit 5: SREN: Single Receive Enable bit Asynchronous mode Don't care Synchronous mode - master 1 = Enables single receive 0 = Disables single receive This bit is cleared after reception is complete. Synchronous mode - slave Unused in this mode bit 4: CREN: Continuous Receive Enable bit Asynchronous mode 1 = Enables continuous receive 0 = Disables continuous receive Synchronous mode 1 = Enables continuous receive until enable bit CREN is cleared (CREN overrides SREN) 0 = Disables continuous receive bit 3: ADDEN: Address Detect Enable bit Asynchronous mode 9-bit (RX9 = 1) 1 = Enables address detection, enable interrupt and load of the receive burffer when RSR<8> is set 0 = Disables address detection, all bytes are received, and ninth bit can be used as parity bit bit 2: FERR: Framing Error bit 1 = Framing error (Can be updated by reading RCREG register and receive next valid byte) 0 = No framing error bit 1: OERR: Overrun Error bit 1 = Overrun error (Can be cleared by clearing bit CREN) 0 = No overrun error bit 0: RX9D: 9th bit of received data (Can be parity bit) DS30569A-page 64 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 9.1 It may be advantageous to use the high baud rate (BRGH = 1) even for slower baud clocks. This is because the FOSC/(16(X + 1)) equation can reduce the baud rate error in some cases. USART Baud Rate Generator (BRG) The BRG supports both the asynchronous and synchronous modes of the USART. It is a dedicated 8-bit baud rate generator. The SPBRG register controls the period of a free running 8-bit timer. In asynchronous mode, bit BRGH (TXSTA<2>) also controls the baud rate. In synchronous mode, bit BRGH is ignored. Table 9-1 shows the formula for computation of the baud rate for different USART modes which only apply in master mode (internal clock). Writing a new value to the SPBRG register causes the BRG timer to be reset (or cleared). This ensures the BRG does not wait for a timer overflow before outputting the new baud rate. 9.1.1 The data on the RC7/RX/DT pin is sampled three times by a majority detect circuit to determine if a high or a low level is present at the RX pin. Given the desired baud rate and Fosc, the nearest integer value for the SPBRG register can be calculated using the formula in Table 9-1. From this, the error in baud rate can be determined. TABLE 9-1: SAMPLING BAUD RATE FORMULA SYNC BRGH = 0 (Low Speed) BRGH = 1 (High Speed) 0 1 (Asynchronous) Baud Rate = FOSC/(64(X+1)) (Synchronous) Baud Rate = FOSC/(4(X+1)) Baud Rate= FOSC/(16(X+1)) NA X = value in SPBRG (0 to 255) TABLE 9-2: Address REGISTERS ASSOCIATED WITH BAUD RATE GENERATOR Name Bit 7 Bit 6 Bit 5 Bit 4 SYNC 98h TXSTA CSRC TX9 TXEN 18h RCSTA SPEN RX9 SREN CREN 99h SPBRG Baud Rate Generator Register Bit 3 Bit 2 -- BRGH ADDEN FERR Bit 1 Bit 0 Value on: POR, BOR Value on all other resets TRMT TX9D 0000 -010 0000 -010 OERR RX9D 0000 000x 0000 000x 0000 0000 0000 0000 Legend: x = unknown, - = unimplemented read as '0'. Shaded cells are not used by the BRG. 1999 Microchip Technology Inc. Preliminary DS30569A-page 65 PIC16F870/871 TABLE 9-3: BAUD RATES FOR ASYNCHRONOUS MODE (BRGH = 0) FOSC = 20 MHz BAUD RATE (K) % ERROR KBAUD FOSC = 16 MHz SPBRG value (decimal) SPBRG value (decimal) % ERROR KBAUD FOSC = 10 MHz KBAUD % ERROR SPBRG value (decimal) 0.3 - - - - - - - - - 1.2 1.221 1.75 255 1.202 0.17 207 1.202 0.17 129 2.4 2.404 0.17 129 2.404 0.17 103 2.404 0.17 64 9.6 9.766 1.73 31 9.615 0.16 25 9.766 1.73 15 19.2 19.531 1.72 15 19.231 0.16 12 19.531 1.72 7 28.8 31.250 8.51 9 27.778 3.55 8 31.250 8.51 4 33.6 34.722 3.34 8 35.714 6.29 6 31.250 6.99 4 57.6 62.500 8.51 4 62.500 8.51 3 52.083 9.58 2 HIGH 1.221 - 255 0.977 - 255 0.610 - 255 LOW 312.500 - 0 250.000 - 0 156.250 - 0 FOSC = 4 MHz BAUD RATE (K) KBAUD FOSC = 3.6864 MHz % ERROR SPBRG value (decimal) KBAUD % ERROR SPBRG value (decimal) 0.3 0.300 0 207 0.301 0.33 185 1.2 1.202 0.17 51 1.216 1.33 46 2.4 2.404 0.17 25 2.432 1.33 22 9.6 8.929 6.99 6 9.322 2.90 5 19.2 20.833 8.51 2 18.643 2.90 2 28.8 31.250 8.51 1 - - - 33.6 - - - - - - 57.6 62.500 8.51 0 55.930 2.90 0 HIGH 0.244 - 255 0.218 - 255 LOW 62.500 - 0 55.930 - 0 - TABLE 9-4: BAUD RATES FOR ASYNCHRONOUS MODE (BRGH = 1) FOSC = 20 MHz BAUD RATE (K) FOSC = 16 MHz KBAUD % ERROR SPBRG value (decimal) 0.3 - - 1.2 - - 2.4 - FOSC = 10 MHz KBAUD % ERROR SPBRG value (decimal) KBAUD % ERROR SPBRG value (decimal) - - - - - - - - - - - - - - - - - - - 2.441 1.71 255 9.6 9.615 0.16 129 9.615 0.16 103 9.615 0.16 64 19.2 19.231 0.16 64 19.231 0.16 51 19.531 1.72 31 28.8 29.070 0.94 42 29.412 2.13 33 28.409 1.36 21 33.6 33.784 0.55 36 33.333 0.79 29 32.895 2.10 18 57.6 59.524 3.34 20 58.824 2.13 16 56.818 1.36 10 HIGH 4.883 - 255 3.906 - 255 2.441 - 255 LOW 1250.000 - 0 1000.000 0 625.000 - 0 FOSC = 4 MHz BAUD RATE (K) KBAUD FOSC = 3.6864 MHz % ERROR SPBRG value (decimal) KBAUD % ERROR SPBRG value (decimal) 0.3 - - - - - - 1.2 1.202 0.17 207 1.203 0.25 185 2.4 2.404 0.17 103 2.406 0.25 92 9.6 9.615 0.16 25 9.727 1.32 22 19.2 19.231 0.16 12 18.643 2.90 11 28.8 27.798 3.55 8 27.965 2.90 7 33.6 35.714 6.29 6 31.960 4.88 6 57.6 62.500 8.51 3 55.930 2.90 3 HIGH 0.977 - 255 0.874 - 255 LOW 250.000 - 0 273.722 - 0 DS30569A-page 66 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 9.2 ( PIE1<4>). Flag bit TXIF will be set, regardless of the state of enable bit TXIE and cannot be cleared in software. It will reset only when new data is loaded into the TXREG register. While flag bit TXIF indicates the status of the TXREG register, another bit TRMT (TXSTA<1>) shows the status of the TSR register. Status bit TRMT is a read only bit, which is set when the TSR register is empty. No interrupt logic is tied to this bit, so the user has to poll this bit in order to determine if the TSR register is empty. USART Asynchronous Mode In this mode, the USART uses standard non-return-tozero (NRZ) format (one start bit, eight or nine data bits, and one stop bit). The most common data format is 8 bits. An on-chip, dedicated, 8-bit baud rate generator can be used to derive standard baud rate frequencies from the oscillator. The USART transmits and receives the LSb first. The USART's transmitter and receiver are functionally independent, but use the same data format and baud rate. The baud rate generator produces a clock either x16 or x64 of the bit shift rate, depending on bit BRGH (TXSTA<2>). Parity is not supported by the hardware, but can be implemented in software (and stored as the ninth data bit). Asynchronous mode is stopped during SLEEP. Note 1: The TSR register is not mapped in data memory, so it is not available to the user. 2: Flag bit TXIF is set when enable bit TXEN is set. TXIF is cleared by loading TXREG. Transmission is enabled by setting enable bit TXEN (TXSTA<5>). The actual transmission will not occur until the TXREG register has been loaded with data and the baud rate generator (BRG) has produced a shift clock (Figure 9-2). The transmission can also be started by first loading the TXREG register and then setting enable bit TXEN. Normally, when transmission is first started, the TSR register is empty. At that point, transfer to the TXREG register will result in an immediate transfer to TSR, resulting in an empty TXREG. A back-to-back transfer is thus possible (Figure 9-3). Clearing enable bit TXEN during a transmission will cause the transmission to be aborted and will reset the transmitter. As a result, the RC6/TX/CK pin will revert to hi-impedance. Asynchronous mode is selected by clearing bit SYNC (TXSTA<4>). The USART Asynchronous module consists of the following important elements: * * * * Baud Rate Generator Sampling Circuit Asynchronous Transmitter Asynchronous Receiver 9.2.1 USART ASYNCHRONOUS TRANSMITTER The USART transmitter block diagram is shown in Figure 9-1. The heart of the transmitter is the transmit (serial) shift register (TSR). The shift register obtains its data from the read/write transmit buffer, TXREG. The TXREG register is loaded with data in software. The TSR register is not loaded until the STOP bit has been transmitted from the previous load. As soon as the STOP bit is transmitted, the TSR is loaded with new data from the TXREG register (if available). Once the TXREG register transfers the data to the TSR register (occurs in one TCY), the TXREG register is empty and flag bit TXIF (PIR1<4>) is set. This interrupt can be enabled/disabled by setting/clearing enable bit TXIE FIGURE 9-1: In order to select 9-bit transmission, transmit bit TX9 (TXSTA<6>) should be set and the ninth bit should be written to TX9D (TXSTA<0>). The ninth bit must be written before writing the 8-bit data to the TXREG register. This is because a data write to the TXREG register can result in an immediate transfer of the data to the TSR register (if the TSR is empty). In such a case, an incorrect ninth data bit may be loaded in the TSR register. USART TRANSMIT BLOCK DIAGRAM Data Bus TXIF TXREG register TXIE 8 MSb (8) * * * LSb 0 Pin Buffer and Control TSR register RC6/TX/CK pin Interrupt TXEN Baud Rate CLK TRMT SPEN SPBRG Baud Rate Generator TX9 TX9D 1999 Microchip Technology Inc. Preliminary DS30569A-page 67 PIC16F870/871 Steps to follow when setting up an Asynchronous Transmission: 4. 1. 5. Initialize the SPBRG register for the appropriate baud rate. If a high speed baud rate is desired, set bit BRGH. (Section 9.1) Enable the asynchronous serial port by clearing bit SYNC and setting bit SPEN. If interrupts are desired, then set enable bit TXIE. 2. 3. FIGURE 9-2: If 9-bit transmission is desired, then set transmit bit TX9. Enable the transmission by setting bit TXEN, which will also set bit TXIF. If 9-bit transmission is selected, the ninth bit should be loaded in bit TX9D. Load data to the TXREG register (starts transmission). 6. 7. ASYNCHRONOUS MASTER TRANSMISSION Write to TXREG BRG output (shift clock) Word 1 RC6/TX/CK (pin) Start Bit Bit 0 Bit 1 Word 1 TXIF bit (Transmit buffer reg. empty flag) TRMT bit (Transmit shift reg. empty flag) FIGURE 9-3: Bit 7/8 Stop Bit Word 1 Transmit Shift Reg ASYNCHRONOUS MASTER TRANSMISSION (BACK TO BACK) Write to TXREG RC6/TX/CK (pin) TXIF bit (interrupt reg. flag) TRMT bit (Transmit shift reg. empty flag) Word 2 Word 1 BRG output (shift clock) Start Bit Bit 0 Bit 1 Word 1 Bit 7/8 Word 1 Transmit Shift Reg. Stop Bit Start Bit Word 2 Bit 0 Word 2 Transmit Shift Reg. Note: This timing diagram shows two consecutive transmissions. TABLE 9-5: Address Name REGISTERS ASSOCIATED WITH ASYNCHRONOUS TRANSMISSION Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 PSPIF(1) ADIF RCIF TXIF -- CCP1IF TMR2IF SPEN RX9 SREN CREN -- FERR OERR 0Ch PIR1 18h RCSTA 19h TXREG USART Transmit Register 8Ch PIE1 98h TXSTA 99h SPBRG Baud Rate Generator Register PSPIE(1) ADIE RCIE TXIE -- CCP1IE TMR2IE CSRC TX9 TXEN SYNC -- BRGH TRMT Bit 0 Value on: POR, BOR TMR1IF 0000 -000 RX9D 0000 -00x Value on all other Resets 0000 -000 0000 -00x 0000 0000 0000 0000 TMR1IE 0000 -000 0000 -000 TX9D 0000 -010 0000 -010 0000 0000 0000 0000 Legend: x = unknown, - = unimplemented locations read as '0'. Shaded cells are not used for asynchronous transmission. Note 1: Bits PSPIE and PSPIF are reserved on the PIC16F870; always maintain these bits clear. DS30569A-page 68 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 9.2.2 for two bytes of data to be received and transferred to the RCREG FIFO and a third byte to begin shifting to the RSR register. On the detection of the STOP bit of the third byte, if the RCREG register is still full, the overrun error bit OERR (RCSTA<1>) will be set. The word in the RSR will be lost. The RCREG register can be read twice to retrieve the two bytes in the FIFO. Overrun bit OERR has to be cleared in software. This is done by resetting the receive logic (CREN is cleared and then set). If bit OERR is set, transfers from the RSR register to the RCREG register are inhibited, so it is essential to clear error bit OERR if it is set. Framing error bit FERR (RCSTA<2>) is set if a stop bit is detected as clear. Bit FERR and the 9th receive bit are buffered the same way as the receive data. Reading the RCREG will load bits RX9D and FERR with new values, therefore it is essential for the user to read the RCSTA register before reading RCREG register in order not to lose the old FERR and RX9D information. USART ASYNCHRONOUS RECEIVER The receiver block diagram is shown in Figure 9-4. The data is received on the RC7/RX/DT pin and drives the data recovery block. The data recovery block is actually a high speed shifter operating at x16 times the baud rate, whereas the main receive serial shifter operates at the bit rate or at FOSC. Once asynchronous mode is selected, reception is enabled by setting bit CREN (RCSTA<4>). The heart of the receiver is the receive (serial) shift register (RSR). After sampling the STOP bit, the received data in the RSR is transferred to the RCREG register (if it is empty). If the transfer is complete, flag bit RCIF (PIR1<5>) is set. The actual interrupt can be enabled/ disabled by setting/clearing enable bit RCIE (PIE1<5>). Flag bit RCIF is a read only bit which is cleared by the hardware. It is cleared when the RCREG register has been read and is empty. The RCREG is a double buffered register (i.e. it is a two deep FIFO). It is possible FIGURE 9-4: USART RECEVE BLOCK DIAGRAM x64 Baud Rate CLK FERR OERR CREN SPBRG /64 or /16 Baud Rate Generator RSR register MSb Stop (8) * * * 7 1 LSb 0 Start RC7/RX/DT Pin Buffer and Control Data Recovery RX9 RX9D SPEN RCREG Register FIFO 8 RCIF Interrupt Data Bus RCIE FIGURE 9-5: RX (pin) ASYNCHRONOUS RECEPTION Start bit bit0 Rcv shift reg Rcv buffer reg Read Rcv buffer reg RCREG bit1 bit7/8 Stop bit Start bit bit0 WORD 1 RCREG bit7/8 Stop bit Start bit bit7/8 Stop bit WORD 2 RCREG RCIF (interrupt flag) OERR bit CREN Note: This timing diagram shows three words appearing on the RX input. The RCREG (receive buffer) is read after the third word, causing the OERR (overrun) bit to be set. 1999 Microchip Technology Inc. Preliminary DS30569A-page 69 PIC16F870/871 Steps to follow when setting up an Asynchronous Reception: 1. 2. 3. 4. 5. 6. Initialize the SPBRG register for the appropriate baud rate. If a high speed baud rate is desired, set bit BRGH. (Section 9.1). Enable the asynchronous serial port by clearing bit SYNC and setting bit SPEN. If interrupts are desired, then set enable bit RCIE. If 9-bit reception is desired, then set bit RX9. Enable the reception by setting bit CREN. TABLE 9-6: Address Name 0Ch PIR1 18h RCSTA 7. 8. 9. Flag bit RCIF will be set when reception is complete and an interrupt will be generated if enable bit RCIE is set. Read the RCSTA register to get the ninth bit (if enabled) and determine if any error occurred during reception. Read the 8-bit received data by reading the RCREG register. If any error occurred, clear the error by clearing enable bit CREN. REGISTERS ASSOCIATED WITH ASYNCHRONOUS RECEPTION Bit 7 Bit 6 PSPIF(1) ADIF SPEN RX9 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR Value on all other Resets RCIF TXIF -- CCP1IF TMR2IF TMR1IF 0000 -000 0000 -000 SREN CREN -- FERR OERR RX9D 0000 -00x 0000 -00x Bit 5 1Ah RCREG USART Receive Register 8Ch PIE1 98h TXSTA 99h SPBRG 0000 0000 0000 0000 PSPIE(1) ADIE RCIE TXIE -- CCP1IE TMR2IE TMR1IE 0000 -000 0000 -000 CSRC TX9 TXEN SYNC -- BRGH TRMT TX9D 0000 -010 0000 -010 0000 0000 0000 0000 Baud Rate Generator Register Legend: x = unknown, - = unimplemented locations read as '0'. Shaded cells are not used for asynchronous reception. Note 1: Bits PSPIE and PSPIF are reserved on the PIC16F870; always maintain these bits clear. DS30569A-page 70 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 9.2.3 SETTING UP 9-BIT MODE WITH ADDRESS DETECT * Flag bit RCIF will be set when reception is complete, and an interrupt will be generated if enable bit RCIE was set. * Read the RCSTA register to get the ninth bit and determine if any error occurred during reception. * Read the 8-bit received data by reading the RCREG register, to determine if the device is being addressed. * If any error occurred, clear the error by clearing enable bit CREN. * If the device has been addressed, clear the ADDEN bit to allow data bytes and address bytes to be read into the receive buffer, and interrupt the CPU. Steps to follow when setting up an Asynchronous Reception with Address Detect Enabled: * Initialize the SPBRG register for the appropriate baud rate. If a high speed baud rate is desired, set bit BRGH. * Enable the asynchronous serial port by clearing bit SYNC and setting bit SPEN. * If interrupts are desired, then set enable bit RCIE. * Set bit RX9 to enable 9-bit reception. * Set ADDEN to enable address detect. * Enable the reception by setting enable bit CREN. FIGURE 9-6: USART RECEIVE BLOCK DIAGRAM x64 Baud Rate CLK FERR OERR CREN SPBRG / 64 MSb / 16 Stop (8) or Baud Rate Generator RSR register 7 * * * 1 LSb 0 Start RC7/RX/DT Pin Buffer and Control Data Recovery RX9 8 SPEN RX9 ADDEN Enable Load of RX9 ADDEN RSR<8> Receive Buffer 8 RX9D RCREG Register FIFO 8 Interrupt RCIF Data Bus RCIE 1999 Microchip Technology Inc. Preliminary DS30569A-page 71 PIC16F870/871 FIGURE 9-7: ASYNCHRONOUS RECEPTION WITH ADDRESS DETECT RC7/RX/DT (pin) Start bit bit0 bit1 bit8 Stop bit Start bit bit0 bit8 Stop bit Load RSR Bit8 = 0, Data Byte WORD 1 RCREG Bit8 = 1, Address Byte Read RCIF Note: This timing diagram shows a data byte followed by an address byte. The data byte is not read into the RCREG (receive buffer) because ADDEN = 1. FIGURE 9-8: RC7/RX/DT (pin) ASYNCHRONOUS RECEPTION WITH ADDRESS BYTE FIRST Start bit bit0 bit1 bit8 Stop bit Start bit bit0 bit8 Stop bit Load RSR Bit8 = 1, Address Byte WORD 1 RCREG Bit8 = 0, Data Byte Read RCIF Note: This timing diagram shows a data byte followed by an address byte. The data byte is not read into the RCREG (receive buffer) because ADDEN was not updated and still = 0. TABLE 9-7: Address Name REGISTERS ASSOCIATED WITH ASYNCHRONOUS RECEPTION Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 PSPIF(1) ADIF RCIF TXIF -- SPEN RX9 SREN 0Ch PIR1 18h RCSTA 1Ah RCREG USART Receive Register 8Ch PIE1 98h TXSTA 99h SPBRG CREN ADDEN PSPIE(1) ADIE RCIE TXIE -- CSRC TX9 TXEN SYNC -- Bit 2 Bit 1 Bit 0 Value on: POR, BOR CCP1IF TMR2IF TMR1IF 0000 -000 FERR OERR RX9D 0000 000x Value on all other Resets 0000 -000 0000 000x 0000 0000 0000 0000 CCP1IE TMR2IE TMR1IE 0000 -000 0000 -000 BRGH Baud Rate Generator Register TRMT TX9D 0000 -010 0000 -010 0000 0000 0000 0000 Legend: x = unknown, - = unimplemented locations read as '0'. Shaded cells are not used for Asynchronous Reception. Note 1: Bits PSPIE and PSPIF are reserved on the PIC16F870; always maintain these bits clear. DS30569A-page 72 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 9.3 USART Synchronous Master Mode In Synchronous Master mode, the data is transmitted in a half-duplex manne (i.e., transmission and reception do not occur at the same time). When transmitting data, the reception is inhibited and vice versa. Synchronous mode is entered by setting bit SYNC (TXSTA<4>). In addition, enable bit SPEN (RCSTA<7>) is set in order to configure the RC6/TX/CK and RC7/RX/DT I/O pins to CK (clock) and DT (data) lines respectively. The Master mode indicates that the processor transmits the master clock on the CK line. The Master mode is entered by setting bit CSRC (TXSTA<7>). 9.3.1 USART SYNCHRONOUS MASTER TRANSMISSION The USART transmitter block diagram is shown in Figure 9-6. The heart of the transmitter is the transmit (serial) shift register (TSR). The shift register obtains its data from the read/write transmit buffer register TXREG. The TXREG register is loaded with data in software. The TSR register is not loaded until the last bit has been transmitted from the previous load. As soon as the last bit is transmitted, the TSR is loaded with new data from the TXREG (if available). Once the TXREG register transfers the data to the TSR register (occurs in one Tcycle), the TXREG is empty and interrupt bit TXIF (PIR1<4>) is set. The interrupt can be enabled/disabled by setting/clearing enable bit TXIE (PIE1<4>). Flag bit TXIF will be set regardless of the state of enable bit TXIE and cannot be cleared in software. It will reset only when new data is loaded into the TXREG register. While flag bit TXIF indicates the status of the TXREG register, another bit TRMT (TXSTA<1>) shows the status of the TSR register. TRMT is a read only bit which is set when the TSR is empty. No interrupt logic is tied to this bit, so the user has to poll this bit in order to determine if the TSR register is empty. The TSR is not mapped in data memory, so it is not available to the user. pin reverts to a hi-impedance state (for a reception). The CK pin will remain an output if bit CSRC is set (internal clock). The transmitter logic, however, is not reset, although it is disconnected from the pins. In order to reset the transmitter, the user has to clear bit TXEN. If bit SREN is set (to interrupt an on-going transmission and receive a single word), then after the single word is received, bit SREN will be cleared and the serial port will revert back to transmitting, since bit TXEN is still set. The DT line will immediately switch from hi-impedance receive mode to transmit and start driving. To avoid this, bit TXEN should be cleared. In order to select 9-bit transmission, the TX9 (TXSTA<6>) bit should be set and the ninth bit should be written to bit TX9D (TXSTA<0>). The ninth bit must be written before writing the 8-bit data to the TXREG register. This is because a data write to the TXREG can result in an immediate transfer of the data to the TSR register (if the TSR is empty). If the TSR was empty and the TXREG was written before writing the "new" TX9D, the "present" value of bit TX9D is loaded. Steps to follow when setting up a Synchronous Master Transmission: 1. 2. 3. 4. 5. 6. 7. Initialize the SPBRG register for the appropriate baud rate (Section 9.1). Enable the synchronous master serial port by setting bits SYNC, SPEN and CSRC. If interrupts are desired, set enable bit TXIE. If 9-bit transmission is desired, set bit TX9. Enable the transmission by setting bit TXEN. If 9-bit transmission is selected, the ninth bit should be loaded in bit TX9D. Start transmission by loading data to the TXREG register. Transmission is enabled by setting enable bit TXEN (TXSTA<5>). The actual transmission will not occur until the TXREG register has been loaded with data. The first data bit will be shifted out on the next available rising edge of the clock on the CK line. Data out is stable around the falling edge of the synchronous clock (Figure 9-9). The transmission can also be started by first loading the TXREG register and then setting bit TXEN (Figure 9-10). This is advantageous when slow baud rates are selected, since the BRG is kept in reset when bits TXEN, CREN and SREN are clear. Setting enable bit TXEN will start the BRG, creating a shift clock immediately. Normally, when transmission is first started, the TSR register is empty, so a transfer to the TXREG register will result in an immediate transfer to TSR resulting in an empty TXREG. Back-to-back transfers are possible. Clearing enable bit TXEN during a transmission will cause the transmission to be aborted and will reset the transmitter. The DT and CK pins will revert to hi-impedance. If either bit CREN or bit SREN is set during a transmission, the transmission is aborted and the DT 1999 Microchip Technology Inc. Preliminary DS30569A-page 73 PIC16F870/871 TABLE 9-8: Address REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER TRANSMISSION Name Bit 7 Bit 6 PSPIF(1) ADIF SPEN RX9 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR Value on all other Resets RCIF TXIF -- CCP1IF TMR2IF TMR1IF 0000 -000 0000 -000 SREN CREN -- FERR OERR RX9D 0000 -00x 0000 -00x Bit 5 0Ch PIR1 18h RCSTA 19h TXREG USART Transmit Register 0000 0000 0000 0000 8Ch PIE1 PSPIE(1) ADIE RCIE TXIE -- CCP1IE TMR2IE TMR1IE 0000 -000 0000 -000 CSRC TX9 TXEN SYNC -- BRGH TRMT TX9D 0000 -010 0000 -010 0000 0000 0000 0000 98h TXSTA 99h SPBRG Baud Rate Generator Register Legend: x = unknown, - = unimplemented, read as '0'. Shaded cells are not used for synchronous master transmission. Note 1: Bits PSPIE and PSPIF are reserved on the PIC16F870; always maintain these bits clear. FIGURE 9-9: SYNCHRONOUS TRANSMISSION Q1Q2 Q3Q4 Q1 Q2Q3 Q4Q1 Q2Q3 Q4Q1 Q2Q3 Q4Q1 Q2 Q3Q4 RC7/RX/DT pin bit 0 bit 1 WORD 1 Q3Q4 Q1Q2 Q3Q4 Q1Q2 Q3Q4 Q1Q2 Q3 Q4Q1 Q2Q3 Q4Q1 Q2Q3 Q4Q1 Q2Q3 Q4 bit 2 bit 7 bit 0 bit 1 WORD 2 bit 7 RC6/TX/CK pin Write to TXREG reg Write word1 Write word2 TXIF bit (Interrupt flag) TRMT TRMT bit TXEN bit '1' '1' Note: Sync master mode; SPBRG = '0'. Continuous transmission of two 8-bit words FIGURE 9-10: SYNCHRONOUS TRANSMISSION (THROUGH TXEN) RC7/RX/DT pin bit0 bit1 bit2 bit6 bit7 RC6/TX/CK pin Write to TXREG reg TXIF bit TRMT bit TXEN bit DS30569A-page 74 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 9.3.2 OERR if it is set. The ninth receive bit is buffered the same way as the receive data. Reading the RCREG register will load bit RX9D with a new value, therefore it is essential for the user to read the RCSTA register before reading RCREG in order not to lose the old RX9D information. USART SYNCHRONOUS MASTER RECEPTION Once synchronous mode is selected, reception is enabled by setting either enable bit SREN (RCSTA<5>) or enable bit CREN (RCSTA<4>). Data is sampled on the RC7/RX/DT pin on the falling edge of the clock. If enable bit SREN is set, then only a single word is received. If enable bit CREN is set, the reception is continuous until CREN is cleared. If both bits are set, CREN takes precedence. After clocking the last bit, the received data in the Receive Shift Register (RSR) is transferred to the RCREG register (if it is empty). When the transfer is complete, interrupt flag bit RCIF (PIR1<5>) is set. The actual interrupt can be enabled/ disabled by setting/clearing enable bit RCIE (PIE1<5>). Flag bit RCIF is a read only bit, which is reset by the hardware. In this case, it is reset when the RCREG register has been read and is empty. The RCREG is a double buffered register (i.e., it is a two deep FIFO). It is possible for two bytes of data to be received and transferred to the RCREG FIFO and a third byte to begin shifting into the RSR register. On the clocking of the last bit of the third byte, if the RCREG register is still full, then overrun error bit OERR (RCSTA<1>) is set. The word in the RSR will be lost. The RCREG register can be read twice to retrieve the two bytes in the FIFO. Bit OERR has to be cleared in software (by clearing bit CREN). If bit OERR is set, transfers from the RSR to the RCREG are inhibited, so it is essential to clear bit TABLE 9-9: Address Steps to follow when setting up a Synchronous Master Reception: 1. Initialize the SPBRG register for the appropriate baud rate. (Section 9.1) 2. Enable the synchronous master serial port by setting bits SYNC, SPEN and CSRC. 3. Ensure bits CREN and SREN are clear. 4. If interrupts are desired, then set enable bit RCIE. 5. If 9-bit reception is desired, then set bit RX9. 6. If a single reception is required, set bit SREN. For continuous reception set bit CREN. 7. Interrupt flag bit RCIF will be set when reception is complete and an interrupt will be generated if enable bit RCIE was set. 8. Read the RCSTA register to get the ninth bit (if enabled) and determine if any error occurred during reception. 9. Read the 8-bit received data by reading the RCREG register. 10. If any error occurred, clear the error by clearing bit CREN. REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION Name Bit 7 Bit 6 PSPIF(1) ADIF SPEN RX9 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR Value on all other Resets RCIF TXIF -- CCP1IF TMR2IF TMR1IF 0000 -000 0000 -000 SREN CREN -- FERR OERR RX9D 0000 -00x 0000 -00x Bit 5 0Ch PIR1 18h RCSTA 1Ah RCREG USART Receive Register 8Ch PIE1 PSPIE(1) ADIE RCIE TXIE -- CCP1IE TMR2IE CSRC TX9 TXEN SYNC -- BRGH TRMT 98h TXSTA 99h SPBRG 0000 0000 0000 0000 TMR1IE 0000 -000 0000 -000 TX9D 0000 -010 0000 -010 0000 0000 0000 0000 Baud Rate Generator Register Legend: x = unknown, - = unimplemented read as '0'. Shaded cells are not used for synchronous master reception. Note 1: Bits PSPIE and PSPIF are reserved on the PIC16F870; always maintain these bits clear. FIGURE 9-11: SYNCHRONOUS RECEPTION (MASTER MODE, SREN) Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 RC7/RX/DT pin bit0 bit1 bit2 bit3 bit4 bit5 bit6 bit7 RC6/TX/CK pin Write to bit SREN SREN bit CREN bit '0' '0' RCIF bit (interrupt) Read RXREG Note: Timing diagram demonstrates SYNC master mode with bit SREN = '1' and bit BRG = '0'. 1999 Microchip Technology Inc. Preliminary DS30569A-page 75 PIC16F870/871 9.4 USART Synchronous Slave Mode 9.4.2 Synchronous slave mode differs from the Master mode in the fact that the shift clock is supplied externally at the RC6/TX/CK pin (instead of being supplied internally in master mode). This allows the device to transfer or receive data while in SLEEP mode. Slave mode is entered by clearing bit CSRC (TXSTA<7>). USART SYNCHRONOUS SLAVE RECEPTION The operation of the synchronous master and slave modes is identical, except in the case of the SLEEP mode. Bit SREN is a "don't care" in slave mode. The operation of the synchronous master and slave modes are identical except in the case of the SLEEP mode. If receive is enabled by setting bit CREN prior to the SLEEP instruction, then a word may be received during SLEEP. On completely receiving the word, the RSR register will transfer the data to the RCREG register and if enable bit RCIE bit is set, the interrupt generated will wake the chip from SLEEP. If the global interrupt is enabled, the program will branch to the interrupt vector (0004h). If two words are written to the TXREG and then the SLEEP instruction is executed, the following will occur: Steps to follow when setting up a Synchronous Slave Reception: a) 1. 9.4.1 b) c) d) e) USART SYNCHRONOUS SLAVE TRANSMIT The first word will immediately transfer to the TSR register and transmit. The second word will remain in TXREG register. Flag bit TXIF will not be set. When the first word has been shifted out of TSR, the TXREG register will transfer the second word to the TSR and flag bit TXIF will now be set. If enable bit TXIE is set, the interrupt will wake the chip from SLEEP and if the global interrupt is enabled, the program will branch to the interrupt vector (0004h). 2. 3. 4. 5. 6. Steps to follow when setting up a Synchronous Slave Transmission: 7. 1. 8. 2. 3. 4. 5. 6. 7. Enable the synchronous slave serial port by setting bits SYNC and SPEN and clearing bit CSRC. Clear bits CREN and SREN. If interrupts are desired, then set enable bit TXIE. If 9-bit transmission is desired, then set bit TX9. Enable the transmission by setting enable bit TXEN. If 9-bit transmission is selected, the ninth bit should be loaded in bit TX9D. Start transmission by loading data to the TXREG register. DS30569A-page 76 Preliminary Enable the synchronous master serial port by setting bits SYNC and SPEN and clearing bit CSRC. If interrupts are desired, set enable bit RCIE. If 9-bit reception is desired, set bit RX9. To enable reception, set enable bit CREN. Flag bit RCIF will be set when reception is complete and an interrupt will be generated, if enable bit RCIE was set. Read the RCSTA register to get the ninth bit (if enabled) and determine if any error occurred during reception. Read the 8-bit received data by reading the RCREG register. If any error occurred, clear the error by clearing bit CREN. 1999 Microchip Technology Inc. PIC16F870/871 TABLE 9-10: Address Name REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE TRANSMISSION Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 PSPIF(1) ADIF RCIF TXIF -- SPEN RX9 SREN CREN ADDEN 0Ch PIR1 18h RCSTA 19h TXREG USART Transmit Register 8Ch PIE1 PSPIE(1) ADIE RCIE TXIE -- 98h TXSTA CSRC TX9 TXEN SYNC -- 99h SPBRG Bit 2 Bit 1 Bit 0 Value on: POR, BOR CCP1IF TMR2IF TMR1IF 0000 -000 FERR OERR RX9D Value on all other Resets 0000 -000 0000 000x 0000 000x 0000 0000 0000 0000 CCP1IE TMR2IE TMR1IE 0000 -000 0000 -000 BRGH TRMT TX9D Baud Rate Generator Register 0000 -010 0000 -010 0000 0000 0000 0000 Legend: x = unknown, - = unimplemented read as '0'. Shaded cells are not used for Synchronous Slave Transmission. Note 1: Bits PSPIE and PSPIF are reserved on the PIC16F870; always maintain these bits clear. TABLE 9-11: Address Name REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE RECEPTION Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 PSPIF(1) ADIF RCIF TXIF -- CCP1IF TMR2IF SPEN RX9 SREN CREN ADDEN FERR OERR 0Ch PIR1 18h RCSTA 1Ah RCREG USART Receive Register 8Ch PIE1 98h TXSTA 99h SPBRG Baud Rate Generator Register PSPIE(1) ADIE RCIE TXIE -- CCP1IE TMR2IE CSRC TX9 TXEN SYNC -- BRGH TRMT Bit 0 Value on: POR, BOR TMR1IF 0000 -000 RX9D 0000 000x Value on all other Resets 0000 -000 0000 000x 0000 0000 0000 0000 TMR1IE 0000 -000 0000 -000 TX9D 0000 -010 0000 -010 0000 0000 0000 0000 Legend: x = unknown, - = unimplemented read as '0'. Shaded cells are not used for Synchronous Slave Reception. Note 1: Bits PSPIE and PSPIF are reserved on the PIC16F870, always maintain these bits clear. 1999 Microchip Technology Inc. Preliminary DS30569A-page 77 PIC16F870/871 NOTES: DS30569A-page 78 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 10.0 ANALOG-TO-DIGITAL CONVERTER (A/D) MODULE The A/D module has four registers. These registers are: * * * * The Analog-to-Digital (A/D) Converter module has five inputs for the PIC16F870 and eight for the PIC16F871. The analog input charges a sample and hold capacitor. The output of the sample and hold capacitor is the input into the converter. The converter then generates a digital result of this analog level via successive approximation. The A/D conversion of the analog input signal results in a corresponding 10-bit digital number. The A/D module has high and low voltage reference input that is software selectable to some combination of VDD, VSS, RA2 or RA3. A/D Result High Register (ADRESH) A/D Result Low Register (ADRESL) A/D Control Register0 (ADCON0) A/D Control Register1 (ADCON1) The ADCON0 register, shown in Register 10-1, controls the operation of the A/D module. The ADCON1 register, shown in Register 10-2, configures the functions of the port pins. The port pins can be configured as analog inputs (RA3 can also be the voltage reference) or as digital I/O. Additional information on using the A/D module can be found in the PICmicroTM Mid-Range MCU Family Reference Manual (DS33023). The A/D converter has a unique feature of being able to operate while the device is in SLEEP mode. To operate in sleep, the A/D clock must be derived from the A/D's internal RC oscillator. REGISTER 10-1: ADCON0 REGISTER (ADDRESS: 1Fh) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 ADCS1 ADCS0 CHS2 CHS1 CHS0 GO/DONE -- ADON bit7 bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset bit 7-6: ADCS1:ADCS0: A/D Conversion Clock Select bits 00 = FOSC/2 01 = FOSC/8 10 = FOSC/32 11 = FRC (clock derived from an RC oscillation) bit 5-3: CHS2:CHS0: Analog Channel Select bits 000 = channel 0, (RA0/AN0) 001 = channel 1, (RA1/AN1) 010 = channel 2, (RA2/AN2) 011 = channel 3, (RA3/AN3) 100 = channel 4, (RA5/AN4) 101 = channel 5, (RE0/AN5)(1) 110 = channel 6, (RE1/AN6)(1) 111 = channel 7, (RE2/AN7)(1) bit 2: GO/DONE: A/D Conversion Status bit If ADON = 1 1 = A/D conversion in progress (setting this bit starts the A/D conversion) 0 = A/D conversion not in progress (This bit is automatically cleared by hardware when the A/D conversion is complete) bit 1: Unimplemented: Read as '0' bit 0: ADON: A/D On bit 1 = A/D converter module is operating 0 = A/D converter module is shutoff and consumes no operating current Note 1: These channels are not available on the PIC16F870. 1999 Microchip Technology Inc. Preliminary DS30569A-page 79 PIC16F870/871 REGISTER 10-2: ADCON1 REGISTER (ADDRESS 9Fh) U-0 U-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 ADFM -- -- -- PCFG3 PCFG2 PCFG1 PCFG0 bit7 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset bit0 bit 7: ADFM: A/D Result format select 1 = Right Justified. 6 most significant bits of ADRESH are read as `0'. 0 = Left Justified. 6 least significant bits of ADRESL are read as `0'. bit 6-4: Unimplemented: Read as '0' bit 3-0: PCFG3:PCFG0: A/D Port Configuration Control bits PCFG3: PCFG0 AN7(1) RE2 AN6(1) RE1 AN5(1) RE0 AN4 RA5 AN3 RA3 AN2 RA2 AN1 RA1 AN0 RA0 VREF+ VREF- CHAN / Refs(2) 0000 A A A A A A A A VDD VSS 8/0 0001 A A A A VREF+ A A A RA3 VSS 7/1 0010 D D D A A A A A VDD VSS 5/0 0011 D D D A VREF+ A A A RA3 VSS 4/1 0100 D D D D A D A A VDD VSS 3/0 0101 D D D D VREF+ D A A RA3 VSS 2/1 011x D D D D D D D D VDD VSS 0/0 1000 A A A A VREF+ VREF- A A RA3 RA2 6/2 1001 D D A A A A A A VDD VSS 6/0 1010 D D A A VREF+ A A A RA3 VSS 5/1 1011 D D A A VREF+ VREF- A A RA3 RA2 4/2 1100 D D D A VREF+ VREF- A A RA3 RA2 3/2 1101 D D D D VREF+ VREF- A A RA3 RA2 2/2 1110 D D D D D D D A VDD VSS 1/0 1111 D D D D VREF+ VREF- D A RA3 RA2 1/2 A = Analog input D = Digital I/O Note 1: These channels are not available on the PIC16F870. 2: This column indicates the number of analog channels available as A/D inputs and the numer of analog channels used as voltage reference inputs. DS30569A-page 80 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 The ADRESH:ADRESL registers contain the 10-bit result of the A/D conversion. When the A/D conversion is complete, the result is loaded into this A/D result register pair, the GO/DONE bit (ADCON0<2>) is cleared and the A/D interrupt flag bit ADIF is set. The block diagram of the A/D module is shown in Figure 10-1. After the A/D module has been configured as desired, the selected channel must be acquired before the conversion is started. The analog input channels must have their corresponding TRIS bits selected as inputs. To determine sample time, see Section 10.1. After this acquisition time has elapsed, the A/D conversion can be started. The following steps should be followed for doing an A/D conversion: 1. 2. 3. 4. 5. Configure the A/D module: * Configure analog pins / voltage reference / and digital I/O (ADCON1) * Select A/D input channel (ADCON0) * Select A/D conversion clock (ADCON0) * Turn on A/D module (ADCON0) Configure A/D interrupt (if desired): * Clear ADIF bit * Set ADIE bit * Set GIE bit Wait the required acquisition time. Start conversion: * Set GO/DONE bit (ADCON0) Wait for A/D conversion to complete, by either: * Polling for the GO/DONE bit to be cleared OR 6. 7. * Waiting for the A/D interrupt Read A/D Result register pair (ADRESH:ADRESL), clear bit ADIF if required. For next conversion, go to step 1 or step 2 as required. The A/D conversion time per bit is defined as TAD. A minimum wait of 2TAD is required before next acquisition starts. 1999 Microchip Technology Inc. Preliminary DS30569A-page 81 PIC16F870/871 FIGURE 10-1: A/D BLOCK DIAGRAM CHS2:CHS0 111 RE2/AN7(1) 110 RE1/AN6(1) 101 RE0/AN5(1) 100 RA5/AN4 VAIN 011 (Input voltage) RA3/AN3/VREF+ 010 RA2/AN2/VREF- A/D Converter 001 RA1/AN1 000 VDD RA0/AN0 VREF+ (Reference voltage) PCFG3:PCFG0 VREF(Reference voltage) VSS PCFG3:PCFG0 Note 1: Not available on PIC16F870. 10.1 A/D Acquisition Requirements For the A/D converter to meet its specified accuracy, the charge holding capacitor (CHOLD) must be allowed to fully charge to the input channel voltage level. The analog input model is shown in Figure 10-2. The source impedance (RS) and the internal sampling switch (RSS) impedance directly affect the time required to charge the capacitor CHOLD. The sampling switch (RSS) impedance varies over the device voltage (VDD), Figure 10-2. The maximum recommended impedance for analog sources is 10 k. As the impedance is decreased, the acquisition time may be decreased. After the analog input channel is selected (changed), this acquisition must be done before the conversion can be started. DS30569A-page 82 To calculate the minimum acquisition time, Equation 10-1 may be used. This equation assumes that 1/2 LSb error is used (1024 steps for the A/D). The 1/2 LSb error is the maximum error allowed for the A/D to meet its specified resolution. To calculate the minimum acquisition time, TACQ, see the PICmicroTM Mid-Range Reference Manual (DS33023). Preliminary 1999 Microchip Technology Inc. PIC16F870/871 EQUATION 10-1: TACQ TC TACQ ACQUISITION TIME = Amplifier Settling Time + Hold Capacitor Charging Time + Temperature Coefficient = = = = = = = TAMP + TC + TCOFF 2S + TC + [(Temperature -25C)(0.05S/C)] CHOLD (RIC + RSS + RS) In(1/2047) - 120pF (1k + 7k + 10k) In(0.0004885) 16.47S 2S + 16.47S + [(50C -25xC)(0.05S/xC) 19.72S Note 1: The reference voltage (VREF) has no effect on the equation, since it cancels itself out. 2: The charge holding capacitor (CHOLD) is not discharged after each conversion. 3: The maximum recommended impedance for analog sources is 10 k. This is required to meet the pin leakage specification. 4: After a conversion has completed, a 2.0TAD delay must complete before acquisition can begin again. During this time, the holding capacitor is not connected to the selected A/D input channel. FIGURE 10-2: ANALOG INPUT MODEL VDD RS VT = 0.6V ANx VA CPIN 5 pF VT = 0.6V RIC 1k Sampling Switch SS RSS CHOLD = DAC capacitance = 120 pF I LEAKAGE 500 nA VSS Legend CPIN = input capacitance VT = threshold voltage I LEAKAGE = leakage current at the pin due to various junctions RIC SS CHOLD 1999 Microchip Technology Inc. = interconnect resistance = sampling switch = sample/hold capacitance (from DAC) Preliminary 6V 5V VDD 4V 3V 2V 5 6 7 8 9 10 11 Sampling Switch ( k ) DS30569A-page 83 PIC16F870/871 10.2 Selecting the A/D Conversion Clock For correct A/D conversions, the A/D conversion clock (TAD) must be selected to ensure a minimum TAD time of 1.6 s. The A/D conversion time per bit is defined as TAD. The A/D conversion requires a minimum 12TAD per 10-bit conversion. The source of the A/D conversion clock is software selected. The four possible options for TAD are: * * * * Table 10-1shows the resultant TAD times derived from the device operating frequencies and the A/D clock source selected. 2TOSC 8TOSC 32TOSC Internal RC oscillator TABLE 10-1: TAD vs. MAXIMUM DEVICE OPERATING FREQUENCIES (STANDARD DEVICES (C)) AD Clock Source (TAD) Maximum Device Frequency Operation ADCS1:ADCS0 Max. 2TOSC 00 1.25 MHz 8TOSC 01 5 MHz 32TOSC 10 20 MHz RC(1, 2, 3) 11 Note 1 Note 1: The RC source has a typical TAD time of 4 s but can vary between 2-6 s. 2: When the device frequencies are greater than 1 MHz, the RC A/D conversion clock source is only recommended for sleep operation. 3: For extended voltage devices (LC), please refer to the Electrical Specifications section. 10.3 Configuring Analog Port Pins The ADCON1, and TRIS registers control the operation of the A/D port pins. The port pins that are desired as analog inputs must have their corresponding TRIS bits set (input). If the TRIS bit is cleared (output), the digital output level (VOH or VOL) will be converted. The A/D operation is independent of the state of the CHS2:CHS0 bits and the TRIS bits. Note 1: When reading the port register, any pin configured as an analog input channel will read as cleared (a low level). Pins configured as digital inputs will convert an analog input. Analog levels on a digitally configured input will not affect the conversion accuracy. 2: Analog levels on any pin that is defined as a digital input (including the AN7:AN0 pins), may cause the input buffer to consume current that is out of the device specifications. DS30569A-page 84 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 10.4 required before the next acquisition is started. After this 2TAD wait, acquisition on the selected channel is automatically started. A/D Conversions Clearing the GO/DONE bit during a conversion will abort the current conversion. The A/D result register pair will NOT be updated with the partially completed A/D conversion sample. That is, the ADRESH:ADRESL registers will continue to contain the value of the last completed conversion (or the last value written to the ADRESH:ADRESL registers). After the A/D conversion is aborted, a 2TAD wait is In Figure 10-3, after the GO bit is set, the first time segmant has a minimum of TCY and a maximum of TAD. Note: The GO/DONE bit should NOT be set in the same instruction that turns on the A/D. FIGURE 10-3: A/D CONVERSION TAD CYCLES TCY to TAD TAD1 TAD2 TAD3 TAD4 TAD5 TAD6 TAD7 TAD8 b9 b8 b7 b6 b5 b4 b3 TAD9 TAD10 TAD11 b2 b1 b0 Conversion Starts Holding capacitor is disconnected from analog input (typically 100 ns) Set GO bit 1999 Microchip Technology Inc. ADRES is loaded, GO bit is cleared, ADIF bit is set, holding capacitor is connected to analog input. Preliminary DS30569A-page 85 PIC16F870/871 10.4.1 A/D RESULT REGISTERS The ADRESH:ADRESL register pair is the location where the 10-bit A/D result is loaded at the completion of the A/D conversion. This register pair is 16-bits wide. The A/D module gives the flexibility to left or right justify the 10-bit result in the 16-bit result register. The A/D Format Select bit (ADFM) controls this justification. Figure 10-4 shows the operation of the A/D result justification. The extra bits are loaded with '0's'. When an A/D result will not overwrite these locations (A/D disable), these registers may be used as two general purpose 8-bit registers. 10.5 SLEEP. If the A/D interrupt is not enabled, the A/D module will then be turned off, although the ADON bit will remain set. When the A/D clock source is another clock option (not RC), a SLEEP instruction will cause the present conversion to be aborted and the A/D module to be turned off, though the ADON bit will remain set. Turning off the A/D places the A/D module in its lowest current consumption state. Note: A/D Operation During Sleep The A/D module can operate during SLEEP mode. This requires that the A/D clock source be set to RC (ADCS1:ADCS0 = 11). When the RC clock source is selected, the A/D module waits one instruction cycle before starting the conversion. This allows the SLEEP instruction to be executed, which eliminates all digital switching noise from the conversion. When the conversion is completed the GO/DONE bit will be cleared and the result loaded into the ADRES register. If the A/D interrupt is enabled, the device will wake-up from 10.6 For the A/D module to operate in SLEEP, the A/D clock source must be set to RC (ADCS1:ADCS0 = 11). To allow the conversion to occur during SLEEP, ensure the SLEEP instruction immediately follows the instruction that sets the GO/DONE bit. Effects of a Reset A device reset forces all registers to their reset state. This forces the A/D module to be turned off, and any conversion is aborted. The value that is in the ADRESH:ADRESL registers is not modified for a Power-on Reset. The ADRESH:ADRESL registers will contain unknown data after a Power-on Reset. FIGURE 10-4: A/D RESULT JUSTIFICATION 10-Bit Result ADFM = 0 ADFM = 1 7 0 2107 7 0765 0000 00 0000 00 ADRESH ADRESL ADRESH ADRESL 10-bit Result 10-bit Result Left Justified Right Justified DS30569A-page 86 0 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 TABLE 10-2: Addr Name REGISTERS/BITS ASSOCIATED WITH A/D Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 POR, BOR MCLR, WDT 0Bh INTCON GIE PEIE T0IE INTE RBIE T0IF INTF RBIF 0000 000x 0000 000u 0Ch PIR1 PSPIF(1) ADIF RCIF TXIF -- CCP1IF TMR2IF TMR1IF 0000 -000 0000 -000 8Ch PIE1 (1) ADIE RCIE TXIE -- CCP1IE TMR2IE TMR1IE 0000 -000 0000 -000 1Eh ADRESH A/D Result Register High Byte xxxx xxxx uuuu uuuu 9Eh ADRESL A/D Result Register Low Byte xxxx xxxx uuuu uuuu 1Fh ADCON0 ADCS1 ADCS0 CHS2 CHS1 CHS0 GO/DONE -- ADON 0000 00-0 0000 00-0 9Fh ADCON1 ADFM -- -- -- PCFG3 PCFG2 PCFG1 PCFG0 --0- 0000 --0- 0000 85h TRISA -- -- PORTA Data Direction Register --11 1111 --11 1111 05h PORTA -- -- PORTA Data Latch when written: PORTA pins when read --0x 0000 --0u 0000 89h(1) TRISE IBF OBF IBOV PSPMODE -- 0000 -111 0000 -111 09h(1) PORTE -- -- -- -- -- ---- -xxx ---- -uuu Legend: Note 1: PSPIE PORTE Data Direction Bits RE2 RE1 RE0 x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used for A/D conversion. These registers/bits are not available on the PIC16F870. 1999 Microchip Technology Inc. Preliminary DS30569A-page 87 PIC16F870/871 NOTES: DS30569A-page 88 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 11.0 SPECIAL FEATURES OF THE CPU These devices have a host of features intended to maximize system reliability, minimize cost through elimination of external components, provide power saving operating modes and offer code protection. These are: * OSC Selection * Reset - Power-on Reset (POR) - Power-up Timer (PWRT) - Oscillator Start-up Timer (OST) - Brown-out Reset (BOR) * Interrupts * Watchdog Timer (WDT) * SLEEP * Code protection * ID locations * In-Circuit Serial Programming * Low Voltage In-Circuit Serial Programming * In-Circuit Debugger 11.1 Configuration Bits The configuration bits can be programmed (read as '0') or left unprogrammed (read as '1') to select various device configurations. These bits are mapped in program memory location 2007h. The user will note that address 2007h is beyond the user program memory space. In fact, it belongs to the special test/configuration memory space (2000h 3FFFh), which can be accessed only during programming. These devices have a watchdog timer, which can be shut off only through configuration bits. It runs off its own RC oscillator for added reliability. There are two timers that offer necessary delays on power-up. One is the Oscillator Start-up Timer (OST), intended to keep the chip in reset until the crystal oscillator is stable. The other is the Power-up Timer (PWRT), which provides a fixed delay of 72 ms (nominal) on power-up only. It is designed to keep the part in reset while the power supply stabilizes. With these two timers on-chip, most applications need no external reset circuitry. SLEEP mode is designed to offer a very low current power-down mode. The user can wake-up from SLEEP through external reset, Watchdog Timer Wake-up, or through an interrupt. Several oscillator options are also made available to allow the part to fit the application. The RC oscillator option saves system cost while the LP crystal option saves power. A set of configuration bits are used to select various options. Additional information on special features is available in the PICmicroTM Mid-Range Reference Manual, (DS33023). 1999 Microchip Technology Inc. Preliminary DS30569A-page 89 PIC16F870/871 REGISTER 11-1: CONFIGURATION WORD CP1 CP0 DEBUG -- WRT CPD LVP BODEN CP1 CP0 PWRTE WDTE bit13 F0SC1 F0SC0 bit0 Register: CONFIG Address 2007h bit 13-12: bit 5-4: CP<1:0>: Flash Program Memory Code Protection bits (2) 11 = Code protection off 10 = Not supported 01 = Not supported 00 = Code protection on bit 11: DEBUG: In-Circuit Debugger Mode 1 = In-Circuit Debugger disabled, RB6 and RB7 are general purpose I/O pins. 0 = In-Circuit Debugger enabled, RB6 and RB7 are dedicated to the debugger. bit 10: Unimplemented: Read as `1' bit 9: WRT: Flash Program Memory Write Enable 1 = Unprotected program memory may be written to by EECON control 0 = Unprotected program memory may not be written to by EECON control bit 8: CPD: Data EE Memory Code Protection 1 = Code protection off 0 = Data EEPROM memory code protected bit 7: LVP: Low Voltage In-Circuit Serial Programming Enable bit 1 = RB3/PGM pin has PGM function, low voltage programming enabled 0 = RB3 is digital I/O, HV on MCLR must be used for programming bit 6: BODEN: Brown-out Reset Enable bit (1) 1 = BOR enabled 0 = BOR disabled bit 3: PWRTE: Power-up Timer Enable bit (1) 1 = PWRT disabled 0 = PWRT enabled bit 2: WDTE: Watchdog Timer Enable bit 1 = WDT enabled 0 = WDT disabled bit 1-0: FOSC1:FOSC0: Oscillator Selection bits 11 = RC oscillator 10 = HS oscillator 01 = XT oscillator 00 = LP oscillator Note 1: Enabling Brown-out Reset automatically enables Power-up Timer (PWRT), regardless of the value of bit PWRTE. Ensure the Power-up Timer is enabled anytime Brown-out Reset is enabled. 2: All of the CP<1:0> pairs have to be given the same value to enable the code protection scheme listed. DS30569A-page 90 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 11.2 Oscillator Configurations 11.2.1 OSCILLATOR TYPES TABLE 11-1: Ranges Tested: The PIC16F870/871 can be operated in four different oscillator modes. The user can program two configuration bits (FOSC1 and FOSC0) to select one of these four modes: * * * * LP XT HS RC 11.2.2 CERAMIC RESONATORS Mode Freq OSC1 OSC2 XT 455 kHz 2.0 MHz 4.0 MHz 68 - 100 pF 15 - 68 pF 15 - 68 pF 68 - 100 pF 15 - 68 pF 15 - 68 pF HS 8.0 MHz 16.0 MHz 10 - 68 pF 10 - 22 pF 10 - 68 pF 10 - 22 pF Low Power Crystal Crystal/Resonator High Speed Crystal/Resonator Resistor/Capacitor These values are for design guidance only. See notes at bottom of page. Resonators Used: CRYSTAL OSCILLATOR/CERAMIC RESONATORS In XT, LP or HS modes, a crystal or ceramic resonator is connected to the OSC1/CLKIN and OSC2/CLKOUT pins to establish oscillation (Figure 11-1). The PIC16F870/871 oscillator design requires the use of a parallel cut crystal. Use of a series cut crystal may give a frequency out of the crystal manufacturers specifications. When in XT, LP or HS modes, the device can have an external clock source to drive the OSC1/ CLKIN pin (Figure 11-2). 455 kHz Panasonic EFO-A455K04B 0.3% 2.0 MHz Murata Erie CSA2.00MG 0.5% 4.0 MHz Murata Erie CSA4.00MG 0.5% 8.0 MHz Murata Erie CSA8.00MT 0.5% 16.0 MHz Murata Erie CSA16.00MX 0.5% All resonators used did not have built-in capacitors. FIGURE 11-1: CRYSTAL/CERAMIC RESONATOR OPERATION (HS, XT OR LP OSC CONFIGURATION) C1(1) OSC1 XTAL RF(3) OSC2 To internal logic SLEEP RS(2) PIC16F870/871 C2(1) Note 1: See Table 11-1 and Table 11-2 for recommended values of C1 and C2. 2: A series resistor (RS) may be required for AT strip cut crystals. 3: RF varies with the crystal chosen. FIGURE 11-2: EXTERNAL CLOCK INPUT OPERATION (HS, XT OR LP OSC CONFIGURATION) OSC1 Clock from ext. system PIC16F870/871 Open OSC2 1999 Microchip Technology Inc. Preliminary DS30569A-page 91 PIC16F870/871 TABLE 11-2: Osc Type LP XT HS CAPACITOR SELECTION FOR CRYSTAL OSCILLATOR Crystal Freq Cap. Range C1 Cap. Range C2 32 kHz 33 pF 33 pF 200 kHz 15 pF 15 pF 200 kHz 47-68 pF 47-68 pF 1 MHz 15 pF 15 pF 4 MHz 15 pF 15 pF 4 MHz 15 pF 15 pF 8 MHz 15-33 pF 15-33 pF 20 MHz 15-33 pF 15-33 pF 11.2.3 RC OSCILLATOR For timing insensitive applications, the "RC" device option offers additional cost savings. The RC oscillator frequency is a function of the supply voltage, the resistor (REXT) and capacitor (CEXT) values, and the operating temperature. In addition to this, the oscillator frequency will vary from unit to unit due to normal process parameter variation. Furthermore, the difference in lead frame capacitance between package types will also affect the oscillation frequency, especially for low CEXT values. The user also needs to take into account variation due to tolerance of external R and C components used. Figure 11-3 shows how the R/C combination is connected to the PIC16F870/871. FIGURE 11-3: RC OSCILLATOR MODE These values are for design guidance only. See notes at bottom of page. VDD Crystals Used 32 kHz Epson C-001R32.768K-A 20 PPM 200 kHz STD XTL 200.000 kHz 20 PPM 1 MHz ECS ECS-10-13-1 50 PPM 4 MHz ECS ECS-40-20-1 50 PPM Cext VSS 8 MHz EPSON CA-301 8.000M-C 30 PPM 20 MHz EPSON CA-301 20.000M-C 30 PPM Rext OSC1 PIC16F870/871 FOSC/4 Recommended values: Note 1: Higher capacitance increases the stability of oscillator but also increases the start-up time. Internal Clock OSC2/CLKOUT 3 k Rext 100 k Cext > 20pF 2: Since each resonator/crystal has its own characteristics, the user should consult the resonator/crystal manufacturer for appropriate values of external components. 3: Rs may be required in HS mode, as well as XT mode, to avoid overdriving crystals with low drive level specification. 4: When migrating from other PICmicro devices, oscillator performance should be verified. DS30569A-page 92 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 11.3 Reset The PIC16F870/871 differentiates between various kinds of reset: * * * * * * Power-on Reset (POR) MCLR reset during normal operation MCLR reset during SLEEP WDT Reset (during normal operation) WDT Wake-up (during SLEEP) Brown-out Reset (BOR) WDT Reset, on MCLR reset during SLEEP, and Brownout Reset (BOR). They are not affected by a WDT Wake-up, which is viewed as the resumption of normal operation. The TO and PD bits are set or cleared differently in different reset situations as indicated in Table 11-4. These bits are used in software to determine the nature of the reset. See Table 11-6 for a full description of reset states of all registers. A simplified block diagram of the on-chip reset circuit is shown in Figure 11-4. Some registers are not affected in any reset condition. Their status is unknown on POR and unchanged in any other reset. Most other registers are reset to a "reset state" on Power-on Reset (POR), on the MCLR and These devices have a MCLR noise filter in the MCLR reset path. The filter will detect and ignore small pulses. It should be noted that a WDT Reset does not drive MCLR pin low. FIGURE 11-4: SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT External Reset MCLR WDT Module WDT SLEEP Time-out Reset VDD rise detect Power-on Reset VDD Brown-out Reset S BODEN OST/PWRT OST Chip_Reset R 10-bit Ripple counter Q OSC1 (1) On-chip RC OSC PWRT 10-bit Ripple counter Enable PWRT Enable OST Note 1: This is a separate oscillator from the RC oscillator of the CLKIN pin. 1999 Microchip Technology Inc. Preliminary DS30569A-page 93 PIC16F870/871 11.4 Power-On Reset (POR) 11.8 A Power-on Reset pulse is generated on-chip when VDD rise is detected (in the range of 1.2V - 1.7V). To take advantage of the POR, tie the MCLR pin directly (or through a resistor) to VDD. This will eliminate external RC components usually needed to create a Poweron Reset. A maximum rise time for VDD is specified. See Electrical Specifications for details. When the device starts normal operation (exits the reset condition), device operating parameters (voltage, frequency, temperature,...) must be met to ensure operation. If these conditions are not met, the device must be held in reset until the operating conditions are met. Brown-out Reset may be used to meet the start-up conditions. For additional information, refer to Application Note, AN007, "Power-up Trouble Shooting", (DS00007). 11.5 Power-up Timer (PWRT) The Power-up Timer provides a fixed 72 ms nominal time-out on power-up only from the POR. The Powerup Timer operates on an internal RC oscillator. The chip is kept in reset as long as the PWRT is active. The PWRT's time delay allows VDD to rise to an acceptable level. A configuration bit is provided to enable/disable the PWRT. The power-up time delay will vary from chip to chip due to VDD, temperature and process variation. See DC parameters for details (TPWRT, parameter #33). 11.6 Time-out Sequence On power-up, the time-out sequence is as follows: The PWRT delay starts (if enabled) when a POR reset occurs. Then OST starts counting 1024 oscillator cycles when PWRT ends (LP, XT, HS). When the OST ends, the device comes out of RESET. If MCLR is kept low long enough, the time-outs will expire. Bringing MCLR high will begin execution immediately. This is useful for testing purposes or to synchronize more than one PIC16CXX device operating in parallel. Table 11-5 shows the reset conditions for the STATUS, PCON and PC registers, while Table 11-6 shows the reset conditions for all the registers. 11.9 Power Control/Status Register (PCON) The Power Control/Status Register, PCON, has up to two bits depending upon the device. Bit0 is Brown-out Reset Status bit, BOR. Bit BOR is unknown on a Power-on Reset. It must then be set by the user and checked on subsequent resets to see if bit BOR cleared, indicating a BOR occurred. The BOR bit is a "don't care" bit and is not necessarily predictable if the Brown-out Reset circuitry is disabled (by clearing bit BODEN in the Configuration Word). Bit1 is POR (Power-on Reset Status bit). It is cleared on a Power-on Reset and unaffected otherwise. The user must set this bit following a Power-on Reset. Oscillator Start-up Timer (OST) The Oscillator Start-up Timer (OST) provides 1024 oscillator cycle (from OSC1 input) delay after the PWRT delay is over. This ensures that the crystal oscillator or resonator has started and stabilized. The OST time-out is invoked only for XT, LP and HS modes and only on Power-on Reset or wake-up from SLEEP. 11.7 Brown-Out Reset (BOR) The configuration bit, BODEN, can enable or disable the Brown-out Reset circuit. If VDD falls below VBOR (parameter D005, about 4V) for longer than TBOR (parameter #35, about 100S), the brown-out situation will reset the device. If VDD falls below VBOR for less than TBOR, a reset may not occur. Once the brown-out occurs, the device will remain in brown-out reset until VDD rises above VBOR. The power-up timer then keeps the device in reset for TPWRT (parameter #33, about 72mS). If VDD should fall below VBOR during TPWRT, the brown-out reset process will restart when VDD rises above VBOR with the power-up timer reset. The power-up timer is always enabled when the brown-out reset circuit is enabled regardless of the state of the PWRT configuration bit. DS30569A-page 94 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 TABLE 11-3: TIME-OUT IN VARIOUS SITUATIONS Oscillator Configuration Power-up Brown-out Wake-up from SLEEP 1024TOSC 72 ms + 1024TOSC 1024TOSC -- 72 ms -- PWRTE = 0 PWRTE = 1 XT, HS, LP 72 ms + 1024TOSC RC 72 ms TABLE 11-4: STATUS BITS AND THEIR SIGNIFICANCE POR BOR TO PD 0 x 1 1 Power-on Reset 0 x 0 x Illegal, TO is set on POR 0 x x 0 Illegal, PD is set on POR 1 0 1 1 Brown-out Reset 1 1 0 1 WDT Reset 1 1 0 0 WDT Wake-up 1 1 u u MCLR Reset during normal operation 1 1 1 0 MCLR Reset during SLEEP or interrupt wake-up from SLEEP TABLE 11-5: RESET CONDITION FOR SPECIAL REGISTERS Program Counter STATUS Register PCON Register Power-on Reset 000h 0001 1xxx ---- --0x MCLR Reset during normal operation 000h 000u uuuu ---- --uu MCLR Reset during SLEEP 000h 0001 0uuu ---- --uu WDT Reset 000h 0000 1uuu ---- --uu PC + 1 uuu0 0uuu ---- --uu 000h 0001 1uuu ---- --u0 uuu1 0uuu ---- --uu Condition WDT Wake-up Brown-out Reset Interrupt wake-up from SLEEP (1) PC + 1 Legend: u = unchanged, x = unknown, - = unimplemented bit read as '0'. Note 1: When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector (0004h). 1999 Microchip Technology Inc. Preliminary DS30569A-page 95 PIC16F870/871 TABLE 11-6: Register INITIALIZATION CONDITIONS FOR ALL REGISTERS Power-on Reset, MCLR Resets Wake-up via WDT or Brown-out Reset WDT Reset Interrupt W 870 871 xxxx xxxx uuuu uuuu uuuu uuuu INDF 870 871 N/A N/A N/A TMR0 870 871 xxxx xxxx uuuu uuuu uuuu uuuu PCL 870 871 0000h 0000h PC + 1(2) (3) STATUS 870 871 0001 1xxx 000q quuu uuuq quuu(3) FSR 870 871 xxxx xxxx uuuu uuuu uuuu uuuu PORTA 870 871 --0x 0000 --0u 0000 --uu uuuu PORTB 870 871 xxxx xxxx uuuu uuuu uuuu uuuu PORTC 870 871 xxxx xxxx uuuu uuuu uuuu uuuu PORTD 870 871 xxxx xxxx uuuu uuuu uuuu uuuu PORTE 870 871 ---- -xxx ---- -uuu ---- -uuu PCLATH 870 871 ---0 0000 ---0 0000 ---u uuuu INTCON 870 871 0000 000x 0000 000u uuuu uuuu(1) PIR1 870 871 r000 -000 r000 -000 ruuu -uuu(1) 870 871 0000 -000 0000 -000 uuuu -uuu(1) PIR2 870 871 ---0 ------0 ------u ----(1) TMR1L 870 871 xxxx xxxx uuuu uuuu uuuu uuuu TMR1H 870 871 xxxx xxxx uuuu uuuu uuuu uuuu T1CON 870 871 --00 0000 --uu uuuu --uu uuuu TMR2 870 871 0000 0000 0000 0000 uuuu uuuu T2CON 870 871 -000 0000 -000 0000 -uuu uuuu CCPR1L 870 871 xxxx xxxx uuuu uuuu uuuu uuuu CCPR1H 870 871 xxxx xxxx uuuu uuuu uuuu uuuu CCP1CON 870 871 --00 0000 --00 0000 --uu uuuu RCSTA 870 871 0000 000x 0000 000x uuuu uuuu TXREG 870 871 0000 0000 0000 0000 uuuu uuuu RCREG 870 871 0000 0000 0000 0000 uuuu uuuu ADRESH 870 871 xxxx xxxx uuuu uuuu uuuu uuuu ADCON0 870 871 0000 00-0 0000 00-0 uuuu uu-u OPTION_REG 870 871 1111 1111 1111 1111 uuuu uuuu TRISA 870 871 --11 1111 --11 1111 --uu uuuu TRISB 870 871 1111 1111 1111 1111 uuuu uuuu TRISC 870 871 1111 1111 1111 1111 uuuu uuuu TRISD 870 871 1111 1111 1111 1111 uuuu uuuu TRISE 870 871 0000 -111 0000 -111 uuuu -uuu PIE1 870 871 r000 -000 r000 -000 ruuu -uuu 870 871 0000 0000 0000 0000 uuuu uuuu PIE2 870 871 ---0 ------0 ------u ---PCON 870 871 ---- --qq ---- --uu ---- --uu PR2 870 871 1111 1111 1111 1111 1111 1111 TXSTA 870 871 0000 -010 0000 -010 uuuu -uuu SPBRG 870 871 0000 0000 0000 0000 uuuu uuuu ADRESL 870 871 xxxx xxxx uuuu uuuu uuuu uuuu Legend: u = unchanged, x = unknown, - = unimplemented bit, read as '0', q = value depends on condition, r = reserved maintain clear. Note 1: One or more bits in INTCON, PIR1 and/or PIR2 will be affected (to cause wake-up). 2: When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector (0004h). 3: See Table 11-5 for reset value for specific condition. DS30569A-page 96 Devices Preliminary 1999 Microchip Technology Inc. PIC16F870/871 TABLE 11-6: INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED) Register Devices Power-on Reset, MCLR Resets Wake-up via WDT or Brown-out Reset WDT Reset Interrupt ADCON1 870 871 0--- 0000 0--- 0000 u--- uuuu EEDATA 870 871 0--- 0000 0--- 0000 u--- uuuu EEADR 870 871 xxxx xxxx uuuu uuuu uuuu uuuu EEDATH 870 871 xxxx xxxx uuuu uuuu uuuu uuuu EEADRH 870 871 xxxx xxxx uuuu uuuu uuuu uuuu EECON1 870 871 x--- x000 u--- u000 u--- uuuu EECON2 870 871 ---- ------- ------- ---Legend: u = unchanged, x = unknown, - = unimplemented bit, read as '0', q = value depends on condition, r = reserved maintain clear. Note 1: One or more bits in INTCON, PIR1 and/or PIR2 will be affected (to cause wake-up). 2: When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector (0004h). 3: See Table 11-5 for reset value for specific condition. FIGURE 11-5: TIME-OUT SEQUENCE ON POWER-UP (MCLR TIED TO VDD) VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET FIGURE 11-6: TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD): CASE 1 VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET 1999 Microchip Technology Inc. Preliminary DS30569A-page 97 PIC16F870/871 FIGURE 11-7: TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD): CASE 2 VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET FIGURE 11-8: SLOW RISE TIME (MCLR TIED TO VDD) 5V VDD 1V 0V MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET DS30569A-page 98 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 11.10 The RB0/INT pin interrupt, the RB port change interrupt and the TMR0 overflow interrupt flags are contained in the INTCON register. Interrupts The PIC16F870/871 family has up to 11 sources of interrupt. The interrupt control register (INTCON) records individual interrupt requests in flag bits. It also has individual and global interrupt enable bits. Note: The peripheral interrupt flags are contained in the special function registers, PIR1 and PIR2. The corresponding interrupt enable bits are contained in special function registers, PIE1 and PIE2, and the peripheral interrupt enable bit is contained in special function register INTCON. Individual interrupt flag bits are set, regardless of the status of their corresponding mask bit or the GIE bit. A global interrupt enable bit, GIE (INTCON<7>) enables (if set) all un-masked interrupts or disables (if cleared) all interrupts. When bit GIE is enabled, and an interrupt's flag bit and mask bit are set, the interrupt will vector immediately. Individual interrupts can be disabled through their corresponding enable bits in various registers. Individual interrupt bits are set regardless of the status of the GIE bit. The GIE bit is cleared on reset. When an interrupt is responded to, the GIE bit is cleared to disable any further interrupt, the return address is pushed onto the stack and the PC is loaded with 0004h. Once in the interrupt service routine, the source(s) of the interrupt can be determined by polling the interrupt flag bits. The interrupt flag bit(s) must be cleared in software before re-enabling interrupts to avoid recursive interrupts. For external interrupt events, such as the INT pin or PORTB change interrupt, the interrupt latency will be three or four instruction cycles. The exact latency depends when the interrupt event occurs. The latency is the same for one or two cycle instructions. Individual interrupt flag bits are set regardless of the status of their corresponding mask bit or the GIE bit The "return from interrupt" instruction, RETFIE, exits the interrupt routine, as well as sets the GIE bit, which re-enables interrupts. FIGURE 11-9: INTERRUPT LOGIC EEIF EEIE PSPIF PSPIE ADIF ADIE Wake-up (If in SLEEP mode) T0IF T0IE INTF INTE RCIF RCIE TXIF TXIE Interrupt to CPU RBIF RBIE PEIE CCP1IF CCP1IE GIE TMR2IF TMR2IE TMR1IF TMR1IE The following table shows which devices have which interrupts. Device T0IF INTF RBIF PIC16F870 Yes Yes Yes - Yes Yes Yes Yes Yes Yes Yes PIC16F871 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes 1999 Microchip Technology Inc. PSPIF ADIF RCIF Preliminary TXIF CCP1IF TMR2IF TMR1IF EEIF DS30569A-page 99 PIC16F870/871 11.10.1 INT INTERRUPT 11.10.3 PORTB INTCON CHANGE External interrupt on the RB0/INT pin is edge triggered, either rising, if bit INTEDG (OPTION_REG<6>) is set, or falling, if the INTEDG bit is clear. When a valid edge appears on the RB0/INT pin, flag bit INTF (INTCON<1>) is set. This interrupt can be disabled by clearing enable bit INTE (INTCON<4>). Flag bit INTF must be cleared in software in the interrupt service routine before re-enabling this interrupt. The INT interrupt can wake-up the processor from SLEEP, if bit INTE was set prior to going into SLEEP. The status of global interrupt enable bit GIE decides whether or not the processor branches to the interrupt vector following wake-up. See Section 11.13 for details on SLEEP mode. An input change on PORTB<7:4> sets flag bit RBIF (INTCON<0>). The interrupt can be enabled/disabled by setting/clearing enable bit RBIE (INTCON<4>). (Section 3.2) 11.10.2 TMR0 INTERRUPT An overflow (FFh 00h) in the TMR0 register will set flag bit T0IF (INTCON<2>). The interrupt can be enabled/disabled by setting/clearing enable bit T0IE (INTCON<5>). (Section 5.0) 11.11 Context Saving During Interrupts During an interrupt, only the return PC value is saved on the stack. Typically, users may wish to save key registers during an interrupt, (i.e., W register and STATUS register). This will have to be implemented in software. Since the upper 16 bytes of each bank are common in the PIC16F870/871 devices, temporary holding registers W_TEMP, STATUS_TEMP and PCLATH_TEMP should be placed in here. These 16 locations don't require banking and therefore, make it easier for context save and restore. Example 11-1 can be used to save and restore context for interrupts. EXAMPLE 11-1: SAVING STATUS, W, AND PCLATH REGISTERS IN RAM MOVWF SWAPF CLRF MOVWF MOVF MOVWF CLRF : :(ISR) : MOVF MOVWF SWAPF W_TEMP STATUS,W STATUS STATUS_TEMP PCLATH, W PCLATH_TEMP PCLATH ;Copy ;Swap ;bank ;Save ;Only ;Save ;Page PCLATH_TEMP, W PCLATH STATUS_TEMP,W MOVWF SWAPF SWAPF STATUS W_TEMP,F W_TEMP,W ;Restore PCLATH ;Move W into PCLATH ;Swap STATUS_TEMP register into W ;(sets bank to original state) ;Move W into STATUS register ;Swap W_TEMP ;Swap W_TEMP into W DS30569A-page 100 W to TEMP register status to be saved into W 0, regardless of current bank, Clears IRP,RP1,RP0 status to bank zero STATUS_TEMP register required if using pages 1, 2 and/or 3 PCLATH into W zero, regardless of current page Preliminary 1999 Microchip Technology Inc. PIC16F870/871 11.12 WDT time-out period values may be found in the Electrical Specifications section under parameter #31. Values for the WDT prescaler (actually a postscaler, but shared with the Timer0 prescaler) may be assigned using the OPTION_REG register. Watchdog Timer (WDT) The Watchdog Timer is as a free running on-chip RC oscillator which does not require any external components. This RC oscillator is separate from the RC oscillator of the OSC1/CLKIN pin. That means that the WDT will run, even if the clock on the OSC1/CLKIN and OSC2/CLKOUT pins of the device has been stopped, for example, by execution of a SLEEP instruction. During normal operation, a WDT time-out generates a device RESET (Watchdog Timer Reset). If the device is in SLEEP mode, a WDT time-out causes the device to wake-up and continue with normal operation (Watchdog Timer Wake-up). The TO bit in the STATUS register will be cleared upon a Watchdog Timer time-out. Note: The CLRWDT and SLEEP instructions clear the WDT and the postscaler, if assigned to the WDT, and prevent it from timing out and generating a device RESET condition. Note: When a CLRWDT instruction is executed and the prescaler is assigned to the WDT, the prescaler count will be cleared, but the prescaler assignment is not changed. . The WDT can be permanently disabled by clearing configuration bit WDTE (Section 11.1). FIGURE 11-10: WATCHDOG TIMER BLOCK DIAGRAM From TMR0 Clock Source (Figure 5-1) 0 WDT Timer Postscaler M U X 1 8 8 - to - 1 MUX PS2:PS0 PSA WDT Enable Bit To TMR0 (Figure 5-1) 0 1 MUX PSA WDT Time-out Note: PSA and PS2:PS0 are bits in the OPTION_REG register. FIGURE 11-11: SUMMARY OF WATCHDOG TIMER REGISTERS Address Name 2007h Config. bits 81h,181h OPTION_REG Bit 7 Bit 6 (1) BODEN(1) RBPU INTEDG Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 CP1 CP0 PWRTE(1) WDTE FOSC1 FOSC0 T0CS T0SE PSA PS2 PS1 PS0 Legend: Shaded cells are not used by the Watchdog Timer. Note 1: See Register 11-1 for operation of these bits. 1999 Microchip Technology Inc. Preliminary DS30569A-page 101 PIC16F870/871 11.13 Power-down Mode (SLEEP) Power-down mode is entered by executing a SLEEP instruction. If enabled, the Watchdog Timer will be cleared but keeps running, the PD bit (STATUS<3>) is cleared, the TO (STATUS<4>) bit is set, and the oscillator driver is turned off. The I/O ports maintain the status they had before the SLEEP instruction was executed (driving high, low, or hi-impedance). For lowest current consumption in this mode, place all I/O pins at either VDD or VSS, ensure no external circuitry is drawing current from the I/O pin, power-down the A/D and disable external clocks. Pull all I/O pins that are hi-impedance inputs, high or low externally, to avoid switching currents caused by floating inputs. The T0CKI input should also be at VDD or VSS for lowest current consumption. The contribution from on-chip pull-ups on PORTB should be considered. The MCLR pin must be at a logic high level (VIHMC). 11.13.1 WAKE-UP FROM SLEEP The device can wake up from SLEEP through one of the following events: 1. 2. 3. External reset input on MCLR pin. Watchdog Timer wake-up (if WDT was enabled). Interrupt from INT pin, RB port change or some Peripheral Interrupts. External MCLR Reset will cause a device reset. All other events are considered a continuation of program execution and cause a "wake-up". The TO and PD bits in the STATUS register can be used to determine the cause of device reset. The PD bit, which is set on power-up, is cleared when SLEEP is invoked. The TO bit is cleared if a WDT time-out occurred and caused wake-up. clear (disabled), the device continues execution at the instruction after the SLEEP instruction. If the GIE bit is set (enabled), the device executes the instruction after the SLEEP instruction and then branches to the interrupt address (0004h). In cases where the execution of the instruction following SLEEP is not desirable, the user should have a NOP after the SLEEP instruction. 11.13.2 WAKE-UP USING INTERRUPTS When global interrupts are disabled (GIE cleared) and any interrupt source has both its interrupt enable bit and interrupt flag bit set, one of the following will occur: * If the interrupt occurs before the execution of a SLEEP instruction, the SLEEP instruction will complete as a NOP. Therefore, the WDT and WDT postscaler will not be cleared, the TO bit will not be set and PD bits will not be cleared. * If the interrupt occurs during or after the execution of a SLEEP instruction, the device will immediately wake up from sleep. The SLEEP instruction will be completely executed before the wake-up. Therefore, the WDT and WDT postscaler will be cleared, the TO bit will be set and the PD bit will be cleared. Even if the flag bits were checked before executing a SLEEP instruction, it may be possible for flag bits to become set before the SLEEP instruction completes. To determine whether a SLEEP instruction executed, test the PD bit. If the PD bit is set, the SLEEP instruction was executed as a NOP. To ensure that the WDT is cleared, a CLRWDT instruction should be executed before a SLEEP instruction. The following peripheral interrupts can wake the device from SLEEP: 1. 2. 3. 4. 5. 6. 7. PSP read or write. TMR1 interrupt. Timer1 must be operating as an asynchronous counter. CCP capture mode interrupt. Special event trigger (Timer1 in asynchronous mode using an external clock). USART RX or TX (synchronous slave mode). A/D conversion (when A/D clock source is RC). EEPROM write operation completion Other peripherals cannot generate interrupts since during SLEEP, no on-chip clocks are present. When the SLEEP instruction is being executed, the next instruction (PC + 1) is pre-fetched. For the device to wake-up through an interrupt event, the corresponding interrupt enable bit must be set (enabled). Wake-up is regardless of the state of the GIE bit. If the GIE bit is DS30569A-page 102 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 FIGURE 11-12: WAKE-UP FROM SLEEP THROUGH INTERRUPT Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 OSC1 TOST(2) CLKOUT(4) INT pin INTF flag (INTCON<1>) Interrupt Latency (Note 2) GIE bit (INTCON<7>) Processor in SLEEP INSTRUCTION FLOW PC Instruction fetched Instruction executed PC PC+1 Inst(PC) = SLEEP Inst(PC - 1) PC+2 PC+2 Inst(PC + 1) Inst(PC + 2) SLEEP Inst(PC + 1) PC + 2 Dummy cycle 0004h 0005h Inst(0004h) Inst(0005h) Dummy cycle Inst(0004h) Note 1: XT, HS or LP oscillator mode assumed. 2: TOST = 1024TOSC (drawing not to scale) This delay will not be there for RC osc mode. 3: GIE = '1' assumed. In this case after wake- up, the processor jumps to the interrupt routine. If GIE = '0', execution will continue in-line. 4: CLKOUT is not available in these osc modes, but shown here for timing reference. 11.14 11.16 In-Circuit Debugger When the DEBUG bit in the configuration word is programmed to a '0', the In-Circuit Debugger functionality is enabled. This function allows simple debugging functions when used with MPLAB. When the microcontroller has this feature enabled, some of the resources are not available for general use. Table 11-7 shows which features are consumed by the background debugger. TABLE 11-7: ID Locations Four memory locations (2000h - 2003h) are designated as ID locations where the user can store checksum or other code-identification numbers. These locations are not accessible during normal execution but are readable and writable during program/verify. It is recommended that only the 4 least significant bits of the ID location are used. DEBUGGER RESOURCES I/O pins RB6, RB7 Stack 1 level Program Memory Address 0000h must be NOP Last 100h words Data Memory 0x070(0x0F0, 0x170, 0x1F0) 0x1EB - 0x1EF To use the In-Circuit Debugger function of the microcontroller, the design must implement In-Circuit Serial Programming connections to MCLR/VPP, VDD, GND, RB7 and RB6. This will interface to the In-Circuit Debugger module available from Microchip or one of the third party development tool companies. 11.15 Program Verification/Code Protection If the code protection bit(s) have not been programmed, the on-chip program memory can be read out for verification purposes. 1999 Microchip Technology Inc. Preliminary DS30569A-page 103 PIC16F870/871 11.17 In-Circuit Serial Programming 11.18 PIC16F870/871 microcontrollers can be serially programmed while in the end application circuit. This is simply done with two lines for clock and data and three other lines for power, ground, and the programming voltage. This allows customers to manufacture boards with unprogrammed devices, and then program the microcontroller just before shipping the product. This also allows the most recent firmware or a custom firmware to be programmed. When using ICSP, the part must be supplied 4.5V to 5.5V if a bulk erase will be executed. This includes reprogramming of the code protect both from an onstate to off-state. For all other cases of ICSP, the part may be programmed at the normal operating voltages. This means calibration values, unique user IDs or user code can be reprogrammed or added. Low Voltage ICSP Programming The LVP bit of the configuration word enables low voltage ICSP programming. This mode allows the microcontroller to be programmed via ICSP using a VDD source in the operating voltage range. This only means that VPP does not have to be brought to VIHH, but can instead be left at the normal operating voltage. In this mode, the RB3/PGM pin is dedicated to the programming function and ceases to be a general purpose I/O pin. During programming, VDD is applied to the MCLR pin. To enter programming mode, VDD must be applied to the RB3/PGM provided the LVP bit is set. The LVP bit defaults to on (`1') from the factory. Note 1: The high voltage programming mode is always available, regardless of the state of the LVP bit, by applying VIHH to the MCLR pin. For complete details of serial programming, please refer to the In-Circuit Serial Programming (ICSPTM) Guide, (DS30277B). 2: While in low voltage ICSP mode, the RB3 pin can no longer be used as a general purpose I/O pin. If low-voltage programming mode is not used, the LVP bit can be programmed to a '0' and RB3/PGM becomes a digital I/O pin. However, the LVP bit may only be programmed when programming is entered with VIHH on MCLR. The LVP bit can only be charged when using high voltage on MCLR. It should be noted, that once the LVP bit is programmed to 0, only the high voltage programming mode is available and only high voltage programming mode can be used to program the device. When using low voltage ICSP, the part must be supplied 4.5V to 5.5V if a bulk erase will be executed. This includes reprogramming of the code protect bits from an on-state to off-state. For all other cases of low voltage ICSP, the part may be programmed at the normal operating voltage. This means calibration values, unique user IDs or user code can be reprogrammed or added. DS30569A-page 104 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 12.0 INSTRUCTION SET SUMMARY Each PIC16CXX instruction is a 14-bit word divided into an OPCODE which specifies the instruction type and one or more operands which further specify the operation of the instruction. The PIC16CXX instruction set summary in Table 12-2 lists byte-oriented, bit-oriented, and literal and control operations. Table 12-1 shows the opcode field descriptions. For byte-oriented instructions, 'f' represents a file register designator and 'd' represents a destination designator. The file register designator specifies which file register is to be used by the instruction. The destination designator specifies where the result of the operation is to be placed. If 'd' is zero, the result is placed in the W register. If 'd' is one, the result is placed in the file register specified in the instruction. For bit-oriented instructions, 'b' represents a bit field designator which selects the number of the bit affected by the operation, while 'f' represents the number of the file in which the bit is located. execution time is 1 s. If a conditional test is true or the program counter is changed as a result of an instruction, the instruction execution time is 2 s. Table 12-2 lists the instructions recognized by the MPASM assembler. Figure 12-1 shows the general formats that the instructions can have. Note: All examples use the following format to represent a hexadecimal number: 0xhh where h signifies a hexadecimal digit. FIGURE 12-1: GENERAL FORMAT FOR INSTRUCTIONS Byte-oriented file register operations 13 8 7 6 OPCODE d f (FILE #) For literal and control operations, 'k' represents an eight or eleven bit constant or literal value. TABLE 12-1: Bit-oriented file register operations 13 10 9 7 6 OPCODE b (BIT #) Description f Register file address (0x00 to 0x7F) W Working register (accumulator) b Bit address within an 8-bit file register k Literal field, constant data or label x Don't care location (= 0 or 1) The assembler will generate code with x = 0. It is the recommended form of use for compatibility with all Microchip software tools. d Program Counter TO Time-out bit PD 0 f (FILE #) b = 3-bit bit address f = 7-bit file register address Literal and control operations General 13 8 7 OPCODE Destination select; d = 0: store result in W, d = 1: store result in file register f. Default is d = 1 PC 0 d = 0 for destination W d = 1 for destination f f = 7-bit file register address OPCODE FIELD DESCRIPTIONS Field To maintain upward compatibility with future PIC16CXX products, do not use the OPTION and TRIS instructions. 0 k (literal) k = 8-bit immediate value CALL and GOTO instructions only 13 11 OPCODE Power-down bit 10 0 k (literal) k = 11-bit immediate value The instruction set is highly orthogonal and is grouped into three basic categories: A description of each instruction is available in the PICmicroTM Mid-Range Reference Manual, (DS33023). * Byte-oriented operations * Bit-oriented operations * Literal and control operations All instructions are executed within one single instruction cycle, unless a conditional test is true or the program counter is changed as a result of an instruction. In this case, the execution takes two instruction cycles with the second cycle executed as a NOP. One instruction cycle consists of four oscillator periods. Thus, for an oscillator frequency of 4 MHz, the normal instruction 1999 Microchip Technology Inc. Preliminary DS30569A-page 105 PIC16F870/871 TABLE 12-2: PIC16CXXX INSTRUCTION SET Mnemonic, Operands Description Cycles 14-Bit Opcode MSb LSb Status Affected Notes C,DC,Z Z Z Z Z Z 1,2 1,2 2 BYTE-ORIENTED FILE REGISTER OPERATIONS ADDWF ANDWF CLRF CLRW COMF DECF DECFSZ INCF INCFSZ IORWF MOVF MOVWF NOP RLF RRF SUBWF SWAPF XORWF f, d f, d f f, d f, d f, d f, d f, d f, d f, d f f, d f, d f, d f, d f, d Add W and f AND W with f Clear f Clear W Complement f Decrement f Decrement f, Skip if 0 Increment f Increment f, Skip if 0 Inclusive OR W with f Move f Move W to f No Operation Rotate Left f through Carry Rotate Right f through Carry Subtract W from f Swap nibbles in f Exclusive OR W with f 1 1 1 1 1 1 1(2) 1 1(2) 1 1 1 1 1 1 1 1 1 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0111 0101 0001 0001 1001 0011 1011 1010 1111 0100 1000 0000 0000 1101 1100 0010 1110 0110 dfff dfff lfff 0xxx dfff dfff dfff dfff dfff dfff dfff lfff 0xx0 dfff dfff dfff dfff dfff ffff ffff ffff xxxx ffff ffff ffff ffff ffff ffff ffff ffff 0000 ffff ffff ffff ffff ffff 00bb 01bb 10bb 11bb bfff bfff bfff bfff ffff ffff ffff ffff 111x 1001 0kkk 0000 1kkk 1000 00xx 0000 01xx 0000 0000 110x 1010 kkkk kkkk kkkk 0110 kkkk kkkk kkkk 0000 kkkk 0000 0110 kkkk kkkk kkkk kkkk kkkk 0100 kkkk kkkk kkkk 1001 kkkk 1000 0011 kkkk kkkk Z Z Z C C C,DC,Z Z 1,2 1,2 1,2,3 1,2 1,2,3 1,2 1,2 1,2 1,2 1,2 1,2 1,2 BIT-ORIENTED FILE REGISTER OPERATIONS BCF BSF BTFSC BTFSS f, b f, b f, b f, b Bit Clear f Bit Set f Bit Test f, Skip if Clear Bit Test f, Skip if Set ADDLW ANDLW CALL CLRWDT GOTO IORLW MOVLW RETFIE RETLW RETURN SLEEP SUBLW XORLW k k k k k k k k k Add literal and W AND literal with W Call subroutine Clear Watchdog Timer Go to address Inclusive OR literal with W Move literal to W Return from interrupt Return with literal in W Return from Subroutine Go into standby mode Subtract W from literal Exclusive OR literal with W 1 1 1 (2) 1 (2) 01 01 01 01 1,2 1,2 3 3 LITERAL AND CONTROL OPERATIONS 1 1 2 1 2 1 1 2 2 2 1 1 1 11 11 10 00 10 11 11 00 11 00 00 11 11 C,DC,Z Z TO,PD Z TO,PD C,DC,Z Z Note 1: When an I/O register is modified as a function of itself ( e.g., MOVF PORTB, 1), the value used will be that value present on the pins themselves. For example, if the data latch is '1' for a pin configured as input and is driven low by an external device, the data will be written back with a '0'. 2: If this instruction is executed on the TMR0 register (and, where applicable, d = 1), the prescaler will be cleared if assigned to the Timer0 Module. 3: If Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second cycle is executed as a NOP. Note: Additional information on the mid-range instruction set is available in the PICmicroTM Mid-Range MCU Family Reference Manual (DS33023). DS30569A-page 106 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 12.1 Instruction Descriptions ADDLW Add Literal and W ANDWF AND W with f Syntax: [label] ADDLW Syntax: [label] ANDWF Operands: 0 k 255 Operands: 0 f 127 d [0,1] k f,d Operation: (W) + k (W) Status Affected: C, DC, Z Operation: (W) .AND. (f) (destination) Description: The contents of the W register are added to the eight bit literal 'k' and the result is placed in the W register. Status Affected: Z Description: AND the W register with register 'f'. If 'd' is 0, the result is stored in the W register. If 'd' is 1, the result is stored back in register 'f'. BCF Bit Clear f Syntax: [label] BCF Operands: 0 f 127 0b7 Operation: 0 (f<b>) Status Affected: None Description: Bit 'b' in register 'f' is cleared. BSF Bit Set f ADDWF Add W and f Syntax: [label] ADDWF Operands: 0 f 127 d [0,1] Operation: (W) + (f) (destination) Status Affected: C, DC, Z Description: Add the contents of the W register with register 'f'. If 'd' is 0, the result is stored in the W register. If 'd' is 1, the result is stored back in register 'f'. f,d ANDLW AND Literal with W Syntax: [label] BSF Operands: 0 f 127 0b7 1 (f<b>) f,b f,b Syntax: [label] ANDLW Operands: 0 k 255 Operation: Operation: (W) .AND. (k) (W) Status Affected: None Status Affected: Z Description: Bit 'b' in register 'f' is set. Description: The contents of W register are AND'ed with the eight bit literal 'k'. The result is placed in the W register. 1999 Microchip Technology Inc. k Preliminary DS30569A-page 107 PIC16F870/871 BTFSS Bit Test f, Skip if Set CLRF Clear f Syntax: [label] BTFSS f,b Syntax: [label] CLRF Operands: 0 f 127 0b<7 Operands: 0 f 127 Operation: Operation: skip if (f<b>) = 1 00h (f) 1Z Status Affected: None Status Affected: Z Description: If bit 'b' in register 'f' is '0', the next instruction is executed. If bit 'b' is '1', then the next instruction is discarded and a NOP is executed instead making this a 2TCY instruction. Description: The contents of register 'f' are cleared and the Z bit is set. CLRW Clear W BTFSC Bit Test, Skip if Clear Syntax: [label] BTFSC f,b Operands: 0 f 127 0b7 Operation: skip if (f<b>) = 0 Status Affected: None Description: If bit 'b' in register 'f' is '1', the next instruction is executed. If bit 'b', in register 'f', is '0', the next instruction is discarded, and a NOP is executed instead, making this a 2TCY instruction. Syntax: [ label ] CLRW Operands: None Operation: 00h (W) 1Z f Status Affected: Z Description: W register is cleared. Zero bit (Z) is set. CLRWDT Clear Watchdog Timer Syntax: [ label ] CLRWDT Operands: None Operation: 00h WDT 0 WDT prescaler, 1 TO 1 PD CALL Call Subroutine Syntax: [ label ] CALL k Operands: 0 k 2047 Operation: (PC)+ 1 TOS, k PC<10:0>, (PCLATH<4:3>) PC<12:11> Status Affected: TO, PD Status Affected: None Description: Description: Call Subroutine. First, return address (PC+1) is pushed onto the stack. The eleven bit immediate address is loaded into PC bits <10:0>. The upper bits of the PC are loaded from PCLATH. CALL is a two cycle instruction. CLRWDT instruction resets the Watchdog Timer. It also resets the prescaler of the WDT. Status bits TO and PD are set. DS30569A-page 108 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 COMF Complement f GOTO Unconditional Branch Syntax: [ label ] COMF Syntax: [ label ] Operands: 0 f 127 d [0,1] Operands: 0 k 2047 Operation: (f) (destination) Operation: k PC<10:0> PCLATH<4:3> PC<12:11> Status Affected: Z Status Affected: None Description: The contents of register 'f' are complemented. If 'd' is 0, the result is stored in W. If 'd' is 1, the result is stored back in register 'f'. Description: GOTO is an unconditional branch. The eleven bit immediate value is loaded into PC bits <10:0>. The upper bits of PC are loaded from PCLATH<4:3>. GOTO is a two cycle instruction. DECF Decrement f Syntax: [label] DECF f,d INCF Increment f Operands: 0 f 127 d [0,1] Syntax: [ label ] Operands: 0 f 127 d [0,1] (f) + 1 (destination) f,d GOTO k INCF f,d Operation: (f) - 1 (destination) Status Affected: Z Operation: Description: Decrement register 'f'. If 'd' is 0, the result is stored in the W register. If 'd' is 1, the result is stored back in register 'f'. Status Affected: Z Description: The contents of register 'f' are incremented. If 'd' is 0, the result is placed in the W register. If 'd' is 1, the result is placed back in register 'f'. INCFSZ Increment f, Skip if 0 DECFSZ Decrement f, Skip if 0 Syntax: [ label ] DECFSZ f,d Operands: 0 f 127 d [0,1] Operation: (f) - 1 (destination); skip if result = 0 Status Affected: None Description: The contents of register 'f' are decremented. If 'd' is 0, the result is placed in the W register. If 'd' is 1, the result is placed back in register 'f'. If the result is 1, the next instruction is executed. If the result is 0, then a NOP is executed instead making it a 2TCY instruction. 1999 Microchip Technology Inc. Syntax: [ label ] Operands: 0 f 127 d [0,1] Operation: (f) + 1 (destination), skip if result = 0 Status Affected: None Description: The contents of register 'f' are incremented. If 'd' is 0, the result is placed in the W register. If 'd' is 1, the result is placed back in register 'f'. If the result is 1, the next instruction is executed. If the result is 0, a NOP is executed instead making it a 2TCY instruction. Preliminary INCFSZ f,d DS30569A-page 109 PIC16F870/871 IORLW Inclusive OR Literal with W MOVLW Move Literal to W Syntax: [ label ] Syntax: [ label ] Operands: 0 k 255 Operands: 0 k 255 Operation: (W) .OR. k (W) Operation: k (W) Status Affected: Z Status Affected: None Description: The contents of the W register are OR'ed with the eight bit literal 'k'. The result is placed in the W register. Description: The eight bit literal 'k' is loaded into W register. The don't cares will assemble as 0's. MOVWF Move W to f IORWF Inclusive OR W with f Syntax: [ label ] Syntax: [ label ] Operands: Operands: 0 f 127 d [0,1] 0 f 127 Operation: (W) (f) Operation: (W) .OR. (f) (destination) Status Affected: None Status Affected: Z Description: Move data from W register to register 'f'. Description: Inclusive OR the W register with register 'f'. If 'd' is 0 the result is placed in the W register. If 'd' is 1 the result is placed back in register 'f'. NOP No Operation Syntax: [ label ] Operands: None Operation: No operation Status Affected: None Description: No operation. IORLW k IORWF f,d MOVF Move f Syntax: [ label ] Operands: 0 f 127 d [0,1] Operation: (f) (destination) Status Affected: Z Description: The contents of register f are moved to a destination dependant upon the status of d. If d = 0, destination is W register. If d = 1, the destination is file register f itself. d = 1 is useful to test a file register since status flag Z is affected. DS30569A-page 110 MOVF f,d Preliminary MOVLW k MOVWF f NOP 1999 Microchip Technology Inc. PIC16F870/871 RETFIE Return from Interrupt RLF Rotate Left f through Carry Syntax: [ label ] Syntax: [ label ] Operands: None Operands: Operation: TOS PC, 1 GIE 0 f 127 d [0,1] Operation: See description below None Status Affected: C Description: The contents of register 'f' are rotated one bit to the left through the Carry Flag. If 'd' is 0, the result is placed in the W register. If 'd' is 1, the result is stored back in register 'f'. Status Affected: RETFIE RLF C RETLW Return with Literal in W Syntax: [ label ] Operands: Operation: RETLW k f,d Register f RRF Rotate Right f through Carry 0 k 255 Syntax: [ label ] k (W); TOS PC Operands: 0 f 127 d [0,1] Status Affected: None Operation: See description below Description: The W register is loaded with the eight bit literal 'k'. The program counter is loaded from the top of the stack (the return address). This is a two cycle instruction. Status Affected: C Description: The contents of register 'f' are rotated one bit to the right through the Carry Flag. If 'd' is 0, the result is placed in the W register. If 'd' is 1, the result is placed back in register 'f'. RRF f,d C Register f RETURN Return from Subroutine Syntax: [ label ] Operands: None SLEEP Operation: TOS PC Syntax: Status Affected: None [ label ] Description: Return from subroutine. The stack is POPed and the top of the stack (TOS) is loaded into the program counter. This is a two cycle instruction. Operands: None Operation: 00h WDT, 0 WDT prescaler, 1 TO, 0 PD Status Affected: TO, PD Description: The power-down status bit, PD is cleared. Time-out status bit, TO is set. Watchdog Timer and its prescaler are cleared. The processor is put into SLEEP mode with the oscillator stopped. RETURN 1999 Microchip Technology Inc. Preliminary SLEEP DS30569A-page 111 PIC16F870/871 SUBLW Syntax: Subtract W from Literal [ label ] SUBLW k Operands: 0 k 255 Operands: 0 k 255 Operation: k - (W) (W) Operation: (W) .XOR. k (W) Status Affected: C, DC, Z Status Affected: Z Description: The W register is subtracted (2's complement method) from the eight bit literal 'k'. The result is placed in the W register. Description: The contents of the W register are XOR'ed with the eight bit literal 'k'. The result is placed in the W register. SUBWF Syntax: Subtract W from f [ label ] SUBWF f,d XORWF Exclusive OR W with f Syntax: [label] Operands: 0 f 127 d [0,1] Operands: 0 f 127 d [0,1] Operation: (f) - (W) (destination) Operation: (W) .XOR. (f) (destination) Status Affected: C, DC, Z Status Affected: Z Description: Description: Exclusive OR the contents of the W register with register 'f'. If 'd' is 0, the result is stored in the W register. If 'd' is 1, the result is stored back in register 'f'. Subtract (2's complement method) W register from register 'f'. If 'd' is 0, the result is stored in the W register. If 'd' is 1, the result is stored back in register 'f'. SWAPF Swap Nibbles in f Syntax: [ label ] SWAPF f,d Operands: 0 f 127 d [0,1] Operation: (f<3:0>) (destination<7:4>), (f<7:4>) (destination<3:0>) Status Affected: None Description: The upper and lower nibbles of register 'f' are exchanged. If 'd' is 0, the result is placed in W register. If 'd' is 1, the result is placed in register 'f'. DS30569A-page 112 XORLW Exclusive OR Literal with W Syntax: [label] Preliminary XORLW k XORWF f,d 1999 Microchip Technology Inc. PIC16F870/871 13.0 DEVELOPMENT SUPPORT MPLAB allows you to: PICmicro(R) The microcontrollers are supported with a full range of hardware and software development tools: * Integrated Development Environment - MPLAB(R) IDE Software * Assemblers/Compilers/Linkers - MPASM Assembler - MPLAB-C17 and MPLAB-C18 C Compilers - MPLINK/MPLIB Linker/Librarian * Simulators - MPLAB-SIM Software Simulator * Emulators - MPLAB-ICE Real-Time In-Circuit Emulator - PICMASTER(R)/PICMASTER-CE In-Circuit Emulator - ICEPICTM * In-Circuit Debugger - MPLAB-ICD for PIC16F877 * Device Programmers - PRO MATE II Universal Programmer - PICSTART Plus Entry-Level Prototype Programmer * Low-Cost Demonstration Boards - SIMICE - PICDEM-1 - PICDEM-2 - PICDEM-3 - PICDEM-17 - SEEVAL - KEELOQ 13.1 The ability to use MPLAB with Microchip's simulator, MPLAB-SIM, allows a consistent platform and the ability to easily switch from the cost-effective simulator to the full featured emulator with minimal retraining. 13.2 MPASM has a command line interface and a Windows shell and can be used as a standalone application on a Windows 3.x or greater system. MPASM generates relocatable object files, Intel standard HEX files, MAP files to detail memory usage and symbol reference, an absolute LST file which contains source lines and generated machine code, and a COD file for MPLAB debugging. MPASM features include: The MPLAB IDE software brings an ease of software development previously unseen in the 8-bit microcontroller market. MPLAB is a Windows-based application which contains: 1999 Microchip Technology Inc. MPASM Assembler MPASM is a full featured universal macro assembler for all PICmicro MCU's. It can produce absolute code directly in the form of HEX files for device programmers, or it can generate relocatable objects for MPLINK. MPLAB Integrated Development Environment Software * Multiple functionality - editor - simulator - programmer (sold separately) - emulator (sold separately) * A full featured editor * A project manager * Customizable tool bar and key mapping * A status bar * On-line help * Edit your source files (either assembly or `C') * One touch assemble (or compile) and download to PICmicro tools (automatically updates all project information) * Debug using: - source files - absolute listing file - object code * MPASM and MPLINK are integrated into MPLAB projects. * MPASM allows user defined macros to be created for streamlined assembly. * MPASM allows conditional assembly for multi purpose source files. * MPASM directives allow complete control over the assembly process. 13.3 MPLAB-C17 and MPLAB-C18 C Compilers The MPLAB-C17 and MPLAB-C18 Code Development Systems are complete ANSI `C' compilers and integrated development environments for Microchip's PIC17CXXX and PIC18CXXX family of microcontrollers, respectively. These compilers provide powerful integration capabilities and ease of use not found with other compilers. For easier source level debugging, the compilers provide symbol information that is compatible with the MPLAB IDE memory display. Preliminary DS30569A-page 113 PIC16F870/871 13.4 MPLINK/MPLIB Linker/Librarian MPLINK is a relocatable linker for MPASM and MPLAB-C17 and MPLAB-C18. It can link relocatable objects from assembly or C source files along with precompiled libraries using directives from a linker script. MPLIB is a librarian for pre-compiled code to be used with MPLINK. When a routine from a library is called from another source file, only the modules that contains that routine will be linked in with the application. This allows large libraries to be used efficiently in many different applications. MPLIB manages the creation and modification of library files. MPLINK features include: * MPLINK works with MPASM and MPLAB-C17 and MPLAB-C18. * MPLINK allows all memory areas to be defined as sections to provide link-time flexibility. MPLIB features include: * MPLIB makes linking easier because single libraries can be included instead of many smaller files. * MPLIB helps keep code maintainable by grouping related modules together. * MPLIB commands allow libraries to be created and modules to be added, listed, replaced, deleted, or extracted. 13.5 MPLAB-SIM Software Simulator The MPLAB-SIM Software Simulator allows code development in a PC host environment by simulating the PICmicro series microcontrollers on an instruction level. On any given instruction, the data areas can be examined or modified and stimuli can be applied from a file or user-defined key press to any of the pins. The execution can be performed in single step, execute until break, or trace mode. MPLAB-SIM fully supports symbolic debugging using MPLAB-C17 and MPLAB-C18 and MPASM. The Software Simulator offers the flexibility to develop and debug code outside of the laboratory environment making it an excellent multi-project software development tool. 13.6 MPLAB-ICE High Performance Universal In-Circuit Emulator with MPLAB IDE The MPLAB-ICE Universal In-Circuit Emulator is intended to provide the product development engineer with a complete microcontroller design tool set for PICmicro microcontrollers (MCUs). Software control of MPLAB-ICE is provided by the MPLAB Integrated Development Environment (IDE), which allows editing, "make" and download, and source debugging from a single environment. DS30569A-page 114 Interchangeable processor modules allow the system to be easily reconfigured for emulation of different processors. The universal architecture of the MPLAB-ICE allows expansion to support new PICmicro microcontrollers. The MPLAB-ICE Emulator System has been designed as a real-time emulation system with advanced features that are generally found on more expensive development tools. The PC platform and Microsoft(R) Windows 3.x/95/98 environment were chosen to best make these features available to you, the end user. MPLAB-ICE 2000 is a full-featured emulator system with enhanced trace, trigger, and data monitoring features. Both systems use the same processor modules and will operate across the full operating speed range of the PICmicro MCU. 13.7 PICMASTER/PICMASTER CE The PICMASTER system from Microchip Technology is a full-featured, professional quality emulator system. This flexible in-circuit emulator provides a high-quality, universal platform for emulating Microchip 8-bit PICmicro microcontrollers (MCUs). PICMASTER systems are sold worldwide, with a CE compliant model available for European Union (EU) countries. 13.8 ICEPIC ICEPIC is a low-cost in-circuit emulation solution for the Microchip Technology PIC16C5X, PIC16C6X, PIC16C7X, and PIC16CXXX families of 8-bit one-timeprogrammable (OTP) microcontrollers. The modular system can support different subsets of PIC16C5X or PIC16CXXX products through the use of interchangeable personality modules or daughter boards. The emulator is capable of emulating without target application circuitry being present. 13.9 MPLAB-ICD In-Circuit Debugger Microchip's In-Circuit Debugger, MPLAB-ICD, is a powerful, low-cost run-time development tool. This tool is based on the flash PIC16F877 and can be used to develop for this and other PICmicro microcontrollers from the PIC16CXXX family. MPLAB-ICD utilizes the In-Circuit Debugging capability built into the PIC16F87X. This feature, along with Microchip's In-Circuit Serial Programming protocol, offers cost-effective in-circuit flash programming and debugging from the graphical user interface of the MPLAB Integrated Development Environment. This enables a designer to develop and debug source code by watching variables, single-stepping and setting break points. Running at full speed enables testing hardware in real-time. The MPLAB-ICD is also a programmer for the flash PIC16F87X family. Preliminary 1999 Microchip Technology Inc. PIC16F870/871 13.10 PRO MATE II Universal Programmer The PRO MATE II Universal Programmer is a full-featured programmer capable of operating in stand-alone mode as well as PC-hosted mode. PRO MATE II is CE compliant. The PRO MATE II has programmable VDD and VPP supplies which allows it to verify programmed memory at VDD min and VDD max for maximum reliability. It has an LCD display for instructions and error messages, keys to enter commands and a modular detachable socket assembly to support various package types. In stand-alone mode the PRO MATE II can read, verify or program PICmicro devices. It can also set code-protect bits in this mode. 13.11 PICSTART Plus Entry Level Development System The PICSTART programmer is an easy-to-use, lowcost prototype programmer. It connects to the PC via one of the COM (RS-232) ports. MPLAB Integrated Development Environment software makes using the programmer simple and efficient. PICSTART Plus supports all PICmicro devices with up to 40 pins. Larger pin count devices such as the PIC16C92X, and PIC17C76X may be supported with an adapter socket. PICSTART Plus is CE compliant. 13.12 SIMICE Entry-Level Hardware Simulator SIMICE is an entry-level hardware development system designed to operate in a PC-based environment with Microchip's simulator MPLAB-SIM. Both SIMICE and MPLAB-SIM run under Microchip Technology's MPLAB Integrated Development Environment (IDE) software. Specifically, SIMICE provides hardware simulation for Microchip's PIC12C5XX, PIC12CE5XX, and PIC16C5X families of PICmicro 8-bit microcontrollers. SIMICE works in conjunction with MPLAB-SIM to provide non-real-time I/O port emulation. SIMICE enables a developer to run simulator code for driving the target system. In addition, the target system can provide input to the simulator code. This capability allows for simple and interactive debugging without having to manually generate MPLAB-SIM stimulus files. SIMICE is a valuable debugging tool for entry-level system development. 13.13 PICDEM-1 Low-Cost PICmicro Demonstration Board The PICDEM-1 is a simple board which demonstrates the capabilities of several of Microchip's microcontrollers. The microcontrollers supported are: PIC16C5X (PIC16C54 to PIC16C58A), PIC16C61, PIC16C62X, PIC16C71, PIC16C8X, PIC17C42, PIC17C43 and PIC17C44. All necessary hardware and software is included to run basic demo programs. The users can program the sample microcontrollers provided with 1999 Microchip Technology Inc. the PICDEM-1 board, on a PRO MATE II or PICSTART-Plus programmer, and easily test firmware. The user can also connect the PICDEM-1 board to the MPLAB-ICE emulator and download the firmware to the emulator for testing. Additional prototype area is available for the user to build some additional hardware and connect it to the microcontroller socket(s). Some of the features include an RS-232 interface, a potentiometer for simulated analog input, push-button switches and eight LEDs connected to PORTB. 13.14 PICDEM-2 Low-Cost PIC16CXX Demonstration Board The PICDEM-2 is a simple demonstration board that supports the PIC16C62, PIC16C64, PIC16C65, PIC16C73 and PIC16C74 microcontrollers. All the necessary hardware and software is included to run the basic demonstration programs. The user can program the sample microcontrollers provided with the PICDEM-2 board, on a PRO MATE II programmer or PICSTART-Plus, and easily test firmware. The MPLAB-ICE emulator may also be used with the PICDEM-2 board to test firmware. Additional prototype area has been provided to the user for adding additional hardware and connecting it to the microcontroller socket(s). Some of the features include a RS-232 interface, push-button switches, a potentiometer for simulated analog input, a Serial EEPROM to demonstrate usage of the I2C bus and separate headers for connection to an LCD module and a keypad. 13.15 PICDEM-3 Low-Cost PIC16CXXX Demonstration Board The PICDEM-3 is a simple demonstration board that supports the PIC16C923 and PIC16C924 in the PLCC package. It will also support future 44-pin PLCC microcontrollers with a LCD Module. All the necessary hardware and software is included to run the basic demonstration programs. The user can program the sample microcontrollers provided with the PICDEM-3 board, on a PRO MATE II programmer or PICSTART Plus with an adapter socket, and easily test firmware. The MPLAB-ICE emulator may also be used with the PICDEM-3 board to test firmware. Additional prototype area has been provided to the user for adding hardware and connecting it to the microcontroller socket(s). Some of the features include an RS-232 interface, push-button switches, a potentiometer for simulated analog input, a thermistor and separate headers for connection to an external LCD module and a keypad. Also provided on the PICDEM-3 board is an LCD panel, with 4 commons and 12 segments, that is capable of displaying time, temperature and day of the week. The PICDEM-3 provides an additional RS-232 interface and Windows 3.1 software for showing the demultiplexed LCD signals on a PC. A simple serial interface allows the user to construct a hardware demultiplexer for the LCD signals. Preliminary DS30569A-page 115 PIC16F870/871 13.16 PICDEM-17 The PICDEM-17 is an evaluation board that demonstrates the capabilities of several Microchip microcontrollers, including PIC17C752, PIC17C756, PIC17C762, and PIC17C766. All necessary hardware is included to run basic demo programs, which are supplied on a 3.5-inch disk. A programmed sample is included, and the user may erase it and program it with the other sample programs using the PRO MATE II or PICSTART Plus device programmers and easily debug and test the sample code. In addition, PICDEM-17 supports down-loading of programs to and executing out of external FLASH memory on board. The PICDEM-17 is also usable with the MPLAB-ICE or PICMASTER emulator, and all of the sample programs can be run and modified using either emulator. Additionally, a generous prototype area is available for user hardware. 13.17 SEEVAL Evaluation and Programming System The SEEVAL SEEPROM Designer's Kit supports all Microchip 2-wire and 3-wire Serial EEPROMs. The kit includes everything necessary to read, write, erase or program special features of any Microchip SEEPROM product including Smart Serials and secure serials. The Total Endurance Disk is included to aid in tradeoff analysis and reliability calculations. The total kit can significantly reduce time-to-market and result in an optimized system. 13.18 KEELOQ Evaluation and Programming Tools KEELOQ evaluation and programming tools support Microchips HCS Secure Data Products. The HCS evaluation kit includes an LCD display to show changing codes, a decoder to decode transmissions, and a programming interface to program test transmitters. DS30569A-page 116 Preliminary 1999 Microchip Technology Inc. Software Tools Emulators 1999 Microchip Technology Inc. Programmers Debugger a PIC17C4X a a a a a a a PIC16C9XX a a a a a a a PIC16F8XX a a a a a PIC16C8X a a a a a a a PIC16C7XX a a a a a a a PIC16C7X a a a a a a a PIC16F62X a a a PIC16CXXX a a a a a PIC16C6X a a a a a a a PIC16C5X a a a a a a a PIC14000 a a a a a a PIC12CXXX a a a a a a a Preliminary a a a a a a a a a a a a a a a a a * Contact the Microchip Technology Inc. web site at www.microchip.com for information on how to use the MPLAB-ICD In-Circuit Debugger (DV164001) with PIC16C62, 63, 64, 65, 72, 73, 74, 76, 77 ** Contact Microchip Technology Inc. for availability date. Development tool is available on select devices. MCP2510 CAN Developer's Kit MCRFXXX a a a 13.56 MHz Anticollision microID Developer's Kit 125 kHz Anticollision microID Developer's Kit 125 kHz microID Developer's Kit microIDTM Programmer's Kit KEELOQ Transponder Kit KEELOQ(R) Evaluation Kit PICDEM-17 a PICDEM-14A a PICDEM-3 a a a a PICDEM-2 a 24CXX/ 25CXX/ 93CXX a a PICDEM-1 a a a ** ** HCSXXX a SIMICE MPLAB-ICD In-Circuit Debugger ICEPIC Low-Cost In-Circuit Emulator PICMASTER/PICMASTER-CE MPLAB-ICE MPASM/MPLINK MPLAB C18 Compiler * a PRO MATE II Universal Programmer a PICSTARTPlus Low-Cost Universal Dev. Kit a a a * PIC17C7XX a a ** PIC18CXX2 a a MPLAB C17 Compiler TABLE 13-1: Demo Boards and Eval Kits MPLAB Integrated Development Environment PIC16F870/871 DEVELOPMENT TOOLS FROM MICROCHIP MCP2510 a DS30569A-page 117 PIC16F870/871 NOTES: DS30569A-page 118 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 14.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings Ambient temperature under bias................................................................................................................ .-55 to +125C Storage temperature .............................................................................................................................. -65C to +150C Voltage on any pin with respect to VSS (except VDD, MCLR. and RA4).......................................... -0.3V to (VDD + 0.3V) Voltage on VDD with respect to VSS ............................................................................................................ -0.3 to +7.5V Voltage on MCLR with respect to VSS (Note 2).............................................................................................0 to +13.25V Voltage on RA4 with respect to Vss ..................................................................................................................0 to +8.5V Total power dissipation (Note 1)................................................................................................................................1.0W Maximum current out of VSS pin ...........................................................................................................................300 mA Maximum current into VDD pin ..............................................................................................................................250 mA Input clamp current, IIK (VI < 0 or VI > VDD)..................................................................................................................... 20 mA Output clamp current, IOK (VO < 0 or VO > VDD) ............................................................................................................. 20 mA Maximum output current sunk by any I/O pin..........................................................................................................25 mA Maximum output current sourced by any I/O pin ....................................................................................................25 mA Maximum current sunk by PORTA, PORTB, and PORTE (combined) (Note 3)....................................................200 mA Maximum current sourced by PORTA, PORTB, and PORTE (combined) (Note 3) ..............................................200 mA Maximum current sunk by PORTC and PORTD (combined) (Note 3) ..................................................................200 mA Maximum current sourced by PORTC and PORTD (combined) (Note 3) .............................................................200 mA Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD - IOH} + {(VDD - VOH) x IOH} + (VOl x IOL) 2: Voltage spikes below VSS at the MCLR pin, inducing currents greater than 80 mA, may cause latch-up. Thus, a series resistor of 50-100 should be used when applying a "low" level to the MCLR pin, rather than pulling this pin directly to VSS. 3: PORTD and PORTE are not implemented on the 28-pin devices. NOTICE: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. 1999 Microchip Technology Inc. Preliminary DS30569A-page 119 PIC16F870/871 FIGURE 14-1: PIC16FXXX VOLTAGE-FREQUENCY GRAPH 6.0 V 5.5 V Voltage 5.0 V 4.5 V 4.0 V 3.5 V 3.0 V 2.5 V 2.0 V 20 MHz Frequency FIGURE 14-2: PIC16LFXXX VOLTAGE-FREQUENCY GRAPH 6.0 V 5.5 V Voltage 5.0 V 4.5 V 4.0 V 3.5 V 3.0 V Eq 2.5 V 2.0 V Eq 4 MHz tio ua ti ua on 2 n1 10 MHz 20 MHz Frequency Equation 1: FMAX = (6.0 MHz/V) (VDDAPPMIN - 2.0 V) + 4 MHz; VDDAPPMIN = 2.0V - 3.0V Equation 2: FMAX = (10.0 MHz/V) (VDDAPPMIN - 3.0 V) + 10 MHz; VDDAPPMIN = 3.0V - 4.0V Note 1: VDDAPPMIN is the minimum voltage of the PICmicro(R) device in the application. Note 2: FMAX has a maximum frequency of 10MHz. DS30569A-page 120 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 14.1 DC Characteristics: PIC16F870/871 (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial DC CHARACTERISTICS Param No. Characteristic D001 Supply Voltage D001A Sym VDD VDR Min Typ Max Units 4.0 4.5 VBOR* - 5.5 5.5 5.5 V V V - 1.5 - V - VSS - V Conditions XT, RC and LP osc configuration HS osc configuration BOR enabled, Fmax = 14MHz (Note 7) D002* RAM Data Retention Voltage (Note 1) D003 VDD start voltage to VPOR ensure internal Power-on Reset signal D004* VDD rise rate to ensure internal Power-on Reset signal SVDD 0.05 - - D005 Brown-out Reset Voltage VBOR 3.7 4.0 4.35 V D010 Supply Current (Note 2,5) IDD - 1.6 4 mA XT, RC osc configuration FOSC = 4 MHz, VDD = 5.5V (Note 4) - 7 15 mA HS osc configuration FOSC = 20 MHz, VDD = 5.5V IBOR - 85 200 A BOR enabled VDD = 5.0V D020 Power-down Current D021 (Note 3,5) D021A IPD - 10.5 1.5 1.5 42 16 19 A A A VDD = 4.0V, WDT enabled, -40C to +85C VDD = 4.0V, WDT disabled, -0C to +70C VDD = 4.0V, WDT disabled, -40C to +85C D023* IBOR - 85 200 A BOR enabled VDD = 5.0V D013 D015* Brown-out Reset Current (Note 6) Brown-out Reset Current (Note 6) See section on Power-on Reset for details V/ms See section on Power-on Reset for details BODEN bit in configuration word enabled Legend: * These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: This is the limit to which VDD can be lowered without losing RAM data. 2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD MCLR = VDD; WDT enabled/disabled as specified. 3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS. 4: For RC osc configuration, current through Rext is not included. The current through the resistor can be estimated by the formula Ir = VDD/2Rext (mA) with Rext in kOhm. 5: Timer1 oscillator (when enabled) adds approximately 20 A to the specification. This value is from characterization and is for design guidance only. This is not tested. 6: The current is the additional current consumed when this peripheral is enabled. This current should be added to the base IDD or IPD measurement. 7: When BOR is enabled, the device will operate correctly until the VBOR voltage trip point is reached. 1999 Microchip Technology Inc. Preliminary DS30569A-page 121 PIC16F870/871 14.2 DC Characteristics: PIC16LF870/871 (Commercial, Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial DC CHARACTERISTICS Param No. Characteristic Sym Min Typ Max Units Conditions D001 Supply Voltage VDD 2.0 - 5.5 V D002* RAM Data Retention Voltage (Note 1) VDR - 1.5 - V D003 VPOR VDD start voltage to ensure internal Power-on Reset signal - VSS - V D004* VDD rise rate to ensure internal Power-on Reset signal SVDD 0.05 - - D005 Brown-out Reset Voltage VBOR 3.7 4.0 4.35 V D010 Supply Current (Note 2,5) IDD - 0.6 2.0 mA XT, RC osc configuration FOSC = 4 MHz, VDD = 3.0V (Note 4) - 20 35 A LP osc configuration FOSC = 32 kHz, VDD = 3.0V, WDT disabled D010A LP, XT, RC osc configuration (DC - 4 MHz) See section on Power-on Reset for details V/ms See section on Power-on Reset for details BODEN bit in configuration word enabled D015* Brown-out Reset Current IBOR (Note 6) - 85 200 A BOR enabled VDD = 5.0V D020 D021 D021A Power-down Current (Note 3,5) - 7.5 0.8 0.9 30 4.5 5 A A A VDD = 3.0V, WDT enabled, -40C to +85C VDD = 3.0V, WDT disabled, 0C to +70C VDD = 3.0V, WDT disabled, -40C to +85C D023* Brown-out Reset Current IBOR (Note 6) - 85 200 A BOR enabled VDD = 5.0V IPD Legend: * These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: This is the limit to which VDD can be lowered without losing RAM data. 2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD MCLR = VDD; WDT enabled/disabled as specified. 3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS. 4: For RC osc configuration, current through Rext is not included. The current through the resistor can be estimated by the formula Ir = VDD/2Rext (mA) with Rext in kOhm. 5: Timer1 oscillator (when enabled) adds approximately 20 A to the specification. This value is from characterization and is for design guidance only. This is not tested. 6: The current is the additional current consumed when this peripheral is enabled. This current should be added to the base IDD or IPD measurement. DS30569A-page 122 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 14.3 DC Characteristics: PIC16F870/871 (Industrial) DC CHARACTERISTICS Param No. Characteristic Input Low Voltage I/O ports with TTL buffer D030 D030A D031 with Schmitt Trigger buffer D032 MCLR, OSC1 (in RC mode) D033 OSC1 (in XT, HS and LP) Ports RC3 and RC4 D034 with Schmitt Trigger buffer D034A with SMBus Input High Voltage I/O ports D040 with TTL buffer D040A D041 with Schmitt Trigger buffer D042 MCLR D042A OSC1 (XT, HS and LP) D043 OSC1 (in RC mode) Ports RC3 and RC4 D044 with Schmitt Trigger buffer D044A with SMBus D070 PORTB weak pull-up current Input Leakage Current (Notes 2, 3) D060 I/O ports D061 D063 MCLR, RA4/T0CKI OSC1 D080 Output Low Voltage I/O ports D083 OSC2/CLKOUT (RC osc config) D090 Output High Voltage I/O ports (Note 3) D092 OSC2/CLKOUT (RC osc config) Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial Operating voltage VDD range as described in DC spec Section 14.1 and Section 14.2. Sym Min Typ Max Units Conditions VIL VSS VSS VSS VSS VSS - 0.15VDD 0.8V 0.2VDD 0.2VDD 0.3VDD V V V V V For entire VDD range 4.5V VDD 5.5V VSS -0.5 - 0.3VDD 0.6 V V For entire VDD range for VDD = 4.5 to 5.5V - VDD VDD V V 4.5V VDD 5.5V For entire VDD range - VDD VDD VDD VDD V V V V For entire VDD range VDD 5.5 400 V For entire VDD range V for VDD = 4.5 to 5.5V A VDD = 5V, VPIN = VSS VIH 2.0 0.25VDD + 0.8V 0.8VDD 0.8VDD 0.7VDD 0.9VDD 0.7VDD 1.4 IPURB 50 250 - - 1 - - 5 5 - - 0.6 V - - 0.6 V VOH VDD - 0.7 - - V VDD - 0.7 - - V IIL VOL Note1 Note1 A Vss VPIN VDD, Pin at hi-impedance A Vss VPIN VDD A Vss VPIN VDD, XT, HS and LP osc configuration IOL = 8.5 mA, VDD = 4.5V, -40C to +85C IOL = 1.6 mA, VDD = 4.5V, -40C to +85C IOH = -3.0 mA, VDD = 4.5V, -40C to +85C IOH = -1.3 mA, VDD = 4.5V, -40C to +85C Legend: * These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16F870/871 be driven with external clock in RC mode. 2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 3: Negative current is defined as current sourced by the pin. 1999 Microchip Technology Inc. Preliminary DS30569A-page 123 PIC16F870/871 DC CHARACTERISTICS Param Characteristic No. D150* Open-Drain High Voltage D100 D101 D102 D120 D121 D122 D130 D131 D132a Capacitive Loading Specs on Output Pins OSC2 pin All I/O pins and OSC2 (in RC mode) SCL, SDA in I2C mode Data EEPROM Memory Endurance VDD for read/write Erase/write cycle time Program FLASH Memory Endurance VDD for read VDD for erase/write Standard Operating Conditions (unless otherwise stated) Operating temperature -40C TA +85C for industrial Operating voltage VDD range as described in DC spec Section 14.1 and Section 14.2. Sym Min Typ Max Units Conditions VOD - - 8.5 V RA4 pin COSC2 - - 15 pF In XT, HS and LP modes when external clock is used to drive OSC1. CIO CB - - 50 400 pF pF ED VDRW 100K Vmin - 5.5 TDEW - 4 8 EP VPR 1000 Vmin Vmin - 5.5 5.5 E/W 25C at 5V V Using EECON to read/write Vmin = min operating voltage ms E/W 25C at 5V V Vmin = min operating voltage V using EECON to read/write, Vmin = min operating voltage ms D133 Erase/Write cycle time TPEW 4 8 Legend: * These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC16F870/871 be driven with external clock in RC mode. 2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 3: Negative current is defined as current sourced by the pin. DS30569A-page 124 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 14.4 Timing Parameter Symbology The timing parameter symbols have been created following one of the following formats: 1. TppS2ppS 3. TCC:ST (I2C specifications only) 2. TppS 4. Ts (I2C specifications only) T F Frequency Lowercase letters (pp) and their meanings: pp cc CCP1 ck CLKOUT cs CS di SDI do SDO dt Data in io I/O port mc MCLR Uppercase letters and their meanings: S F Fall H High I Invalid (Hi-impedance) L Low I2C only AA BUF output access Bus free TCC:ST (I2C specifications only) CC HD Hold ST DAT DATA input hold STA START condition T Time osc rd rw sc ss t0 t1 wr OSC1 RD RD or WR SCK SS T0CKI T1CKI WR P R V Z Period Rise Valid Hi-impedance High Low High Low SU Setup STO STOP condition FIGURE 14-3: LOAD CONDITIONS Load condition 1 Load condition 2 VDD/2 RL CL Pin CL Pin VSS VSS RL = 464 CL = 50 pF 15 pF for all pins except OSC2, but including PORTD and PORTE outputs as ports for OSC2 output Note: PORTD and PORTE are not implemented on the PIC16F870. 1999 Microchip Technology Inc. Preliminary DS30569A-page 125 PIC16F870/871 FIGURE 14-4: EXTERNAL CLOCK TIMING Q4 Q1 Q2 Q3 Q4 Q1 OSC1 1 3 3 4 4 2 CLKOUT TABLE 14-1: Parameter No. EXTERNAL CLOCK TIMING REQUIREMENTS Sym Characteristic FOSC External CLKIN Frequency (Note 1) Oscillator Frequency (Note 1) 1 TOSC External CLKIN Period (Note 1) Oscillator Period (Note 1) 2 TCY Instruction Cycle Time (Note 1) TosL, External Clock in (OSC1) High TosH or Low Time Min Typ Max DC DC DC DC DC 0.1 4 5 250 250 50 5 250 250 250 50 5 200 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- TCY 4 4 20 200 4 4 20 200 -- -- -- -- -- 10,000 250 250 -- DC Units Conditions MHz MHz MHz kHz MHz MHz MHz kHz ns ns ns s ns ns ns ns s ns XT and RC osc mode HS osc mode (-04) HS osc mode (-20) LP osc mode RC osc mode XT osc mode HS osc mode LP osc mode XT and RC osc mode HS osc mode (-04) HS osc mode (-20) LP osc mode RC osc mode XT osc mode HS osc mode (-04) HS osc mode (-20) LP osc mode TCY = 4/FOSC 100 -- -- ns XT oscillator 2.5 -- -- s LP oscillator 15 -- -- ns HS oscillator 4 TosR, External Clock in (OSC1) Rise -- -- 25 ns XT oscillator TosF or Fall Time -- -- 50 ns LP oscillator -- -- 15 ns HS oscillator Legend: Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Instruction cycle period (TCY) equals four times the input oscillator time-base period. All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at "min." values with an external clock applied to the OSC1/CLKIN pin. When an external clock input is used, the "Max." cycle time limit is "DC" (no clock) for all devices. 3 DS30569A-page 126 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 FIGURE 14-5: CLKOUT AND I/O TIMING Q1 Q4 Q2 Q3 OSC1 11 10 CLKOUT 13 19 14 12 18 16 I/O Pin (input) 15 17 I/O Pin (output) new value old value 20, 21 Note: Refer to Figure 14-3 for load conditions. TABLE 14-2: Param Sym No. CLKOUT AND I/O TIMING REQUIREMENTS Characteristic Min Typ Max Units Conditions 10* TosH2ckL OSC1 to CLKOUT -- 75 200 ns Note 1 11* TosH2ckH OSC1 to CLKOUT -- 75 200 ns Note 1 12* TckR CLKOUT rise time -- 35 100 ns Note 1 13* TckF CLKOUT fall time -- 35 100 ns Note 1 14* TckL2ioV CLKOUT to Port out valid -- -- 0.5TCY + 20 ns Note 1 15* TioV2ckH Port in valid before CLKOUT TOSC + 200 -- -- ns Note 1 16* TckH2ioI 0 -- -- ns Note 1 17* TosH2ioV OSC1 (Q1 cycle) to Port out valid -- 100 255 ns 18* TosH2ioI Standard (F) 100 -- -- ns Extended (LF) 200 -- -- ns Port in hold after CLKOUT OSC1 (Q2 cycle) to Port input invalid (I/O in hold time) 19* TioV2osH Port input valid to OSC1 (I/O in setup time) 0 -- -- ns 20* TioR Port output rise time Standard (F) -- 10 40 ns Extended (LF) -- -- 145 ns 21* TioF Port output fall time Standard (F) -- 10 40 ns -- -- 145 ns 22* Tinp INT pin high or low time TCY -- -- ns 23* Trbp RB7:RB4 change INT high or low time TCY -- -- ns Extended (LF) Legend: * These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. These parameters are asynchronous events not related to any internal clock edges. Note 1: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC. 1999 Microchip Technology Inc. Preliminary DS30569A-page 127 PIC16F870/871 FIGURE 14-6: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP TIMER TIMING VDD MCLR 30 Internal POR 33 PWRT Time-out 32 OSC Time-out Internal Reset Watchdog Timer Reset 31 34 34 I/O Pins Note: Refer to Figure 14-3 for load conditions. FIGURE 14-7: BROWN-OUT RESET TIMING VBOR VDD 35 TABLE 14-3: Parameter No. RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER, AND BROWN-OUT RESET REQUIREMENTS Sym Characteristic Min Typ Max Units Conditions 30 TmcL MCLR Pulse Width (low) 2 -- -- s VDD = 5V, -40C to +85C 31* Twdt Watchdog Timer Time-out Period (No Prescaler) 7 18 33 ms VDD = 5V, -40C to +85C 32 Tost Oscillation Start-up Timer Period -- 1024 TOSC -- -- TOSC = OSC1 period 33* Tpwrt Power up Timer Period 28 72 132 ms VDD = 5V, -40C to +85C 34 TIOZ I/O Hi-impedance from MCLR Low or Watchdog Timer Reset -- -- 2.1 s TBOR Brown-out Reset pulse width 100 -- -- s 35 Legend: * VDD VBOR (D005) These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. DS30569A-page 128 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 FIGURE 14-8: TIMER0 AND TIMER1 EXTERNAL CLOCK TIMINGS RA4/T0CKI 41 40 42 RC0/T1OSO/T1CKI 46 45 47 48 TMR0 or TMR1 Note: Refer to Figure 14-3 for load conditions. TABLE 14-4: TIMER0 AND TIMER1 EXTERNAL CLOCK REQUIREMENTS Param No. Sym Characteristic 40* Tt0H T0CKI High Pulse Width 41* Tt0L T0CKI Low Pulse Width 42* Tt0P T0CKI Period 45* 46* 47* Tt1H Tt1L Tt1P No Prescaler With Prescaler No Prescaler With Prescaler No Prescaler With Prescaler T1CKI High Time Synchronous, Prescaler = 1 Synchronous, Standard(F) Prescaler = Extended(LF) 2,4,8 Asynchronous Standard(F) Extended(LF) T1CKI Low Time Synchronous, Prescaler = 1 Synchronous, Standard(F) Prescaler = Extended(LF) 2,4,8 Asynchronous Standard(F) Extended(LF) T1CKI input period Synchronous Standard(F) Extended(LF) Asynchronous 48 * Standard(F) Extended(LF) Ft1 Timer1 oscillator input frequency range (oscillator enabled by setting bit T1OSCEN) TCKEZtmr1 Delay from external clock edge to timer increment Min Typ Max 0.5TCY + 20 -- -- ns 10 -- -- -- -- -- -- -- -- -- -- ns ns ns ns ns -- -- -- -- -- -- ns ns ns -- -- -- -- -- -- -- -- -- -- ns ns ns ns ns -- -- -- -- -- -- ns ns ns 0.5TCY + 20 10 TCY + 40 Greater of: 20 or TCY + 40 N 0.5TCY + 20 15 25 30 50 0.5TCY + 20 15 25 30 50 Greater of: 30 OR TCY + 40 N Greater of: 50 OR TCY + 40 N 60 100 DC 2Tosc Units Conditions Must also meet parameter 42 Must also meet parameter 42 N = prescale value (2, 4, ..., 256) Must also meet parameter 47 Must also meet parameter 47 N = prescale value (1, 2, 4, 8) N = prescale value (1, 2, 4, 8) -- -- -- -- -- 200 ns ns kHz -- 7Tosc -- These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. 1999 Microchip Technology Inc. Preliminary DS30569A-page 129 PIC16F870/871 FIGURE 14-9: CAPTURE/COMPARE/PWM TIMINGS (CCP1) RC2/CCP1 (Capture Mode) 50 51 52 RC2/CCP1 (Compare or PWM Mode) 53 54 Note: Refer to Figure 14-3 for load conditions. TABLE 14-5: Param No. 50* CAPTURE/COMPARE/PWM REQUIREMENTS (CCP1) Sym Characteristic TccL CCP1 input low time Min No Prescaler Standard(F) With Prescaler 51* TccH CCP1 input high time With Prescaler 52* TccP CCP1 input period 53* TccR CCP1 output rise time 54* * Extended(LF) No Prescaler TccF CCP1 output fall time Typ Max Units Conditions 0.5TCY + 20 -- -- ns 10 -- -- ns 20 -- -- ns 0.5TCY + 20 -- -- ns Standard(F) 10 -- -- ns Extended(LF) 20 -- -- ns 3TCY + 40 N -- -- ns Standard(F) -- 10 25 ns Extended(LF) -- 25 50 ns Standard(F) -- 10 25 ns Extended(LF) -- 25 45 ns N = prescale value (1,4 or 16) These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. DS30569A-page 130 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 FIGURE 14-10: PARALLEL SLAVE PORT TIMING (PIC16F871 ONLY) RE2/CS RE0/RD RE1/WR 65 RD7:RD0 62 64 63 Note: Refer to Figure 14-3 for load conditions. TABLE 14-6: Parameter No. 62 PARALLEL SLAVE PORT REQUIREMENTS (PIC16F871 ONLY) Sym Characteristic Min Typ Max Units TdtV2wrH Data in valid before WR or CS (setup time) 63* TwrH2dtI WR or CS to data-in invalid (hold time) Standard(F) 64 TrdL2dtV RD and CS to data-out valid Extended(LF) 65 * TrdH2dtI RD or CS to data-out invalid 20 25 -- -- -- -- ns ns 20 -- -- ns 35 -- -- ns -- -- -- -- 80 90 ns ns 10 -- 30 ns Conditions Extended Range Only Extended Range Only These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. 1999 Microchip Technology Inc. Preliminary DS30569A-page 131 PIC16F870/871 FIGURE 14-11: USART SYNCHRONOUS TRANSMISSION (MASTER/SLAVE) TIMING RC6/TX/CK Pin 121 121 RC7/RX/DT Pin 120 122 Note: Refer to Figure 14-3 for load conditions. TABLE 14-7: Param No. 120 121 Sym Characteristic TckH2dtV SYNC XMIT (MASTER & SLAVE) Clock high to data out valid Tckrf 122 : USART SYNCHRONOUS TRANSMISSION REQUIREMENTS Tdtrf Min Typ Max Units Conditions Standard(F) -- -- 80 ns Extended(LF) -- -- 100 ns Clock out rise time and fall time Standard(F) (Master Mode) Extended(LF) -- -- 45 ns -- -- 50 ns Data out rise time and fall time Standard(F) -- -- 45 ns Extended(LF) -- -- 50 ns Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. FIGURE 14-12: USART SYNCHRONOUS RECEIVE (MASTER/SLAVE) TIMING RC6/TX/CK pin RC7/RX/DT pin 125 126 Note: Refer to Figure 14-3 for load conditions. TABLE 14-8: Parameter No. 125 126 : USART SYNCHRONOUS RECEIVE REQUIREMENTS Sym Characteristic TdtV2ckL TckL2dtl Min Typ Max Units Conditions SYNC RCV (MASTER & SLAVE) Data setup before CK (DT setup time) 15 -- -- ns Data hold after CK (DT hold time) 15 -- -- ns Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. DS30569A-page 132 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 TABLE 14-9: Param No. Sym A01 NR A03 PIC16F870/871 (INDUSTRIAL) PIC16LF870/871 (INDUSTRIAL) Characteristic Min Typ Max Units Resolution -- -- 10-bits bit VREF = VDD = 5.12V, VSS VAIN VREF EIL Integral linearity error -- -- <1 LSb VREF = VDD = 5.12V, VSS VAIN VREF A04 EDL Differential linearity error -- -- <1 LSb VREF = VDD = 5.12V, VSS VAIN VREF A06 EOFF Offset error -- -- <1 LSb VREF = VDD = 5.12V, VSS VAIN VREF A07 EGN Gain error -- -- <1 LSb VREF = VDD = 5.12V, VSS VAIN VREF A10 -- Monotonicity(3) -- guaranteed -- -- VSS VAIN VREF 2.0V -- VDD + 0.3 V Absolute minimum electrical spec. to ensure 10-bit accuracy. VDD + 0.3V V Must meet spec. A20 Must meet spec. A20 A20 VREF Reference voltage (VREF+ - VREF-) A21 VREF+ Reference voltage High VDD - 2.5V A22 VREF- Reference voltage low VSS - 0.3V VREF+ - 2.0V V VSS - 0.3 -- VREF + 0.3 V -- -- 10.0 k Standard(F) -- 220 -- A Extended(LF) -- 90 -- A 10 -- 1000 A During VAIN acquisition. Based on differential of VHOLD to VAIN to charge CHOLD, see Section 10.1. -- -- 10 A During A/D Conversion cycle A25 VAIN Analog input voltage A30 ZAIN Recommended impedance of analog voltage source A40 IAD A/D conversion current (VDD) A50 IREF Conditions VREF input current (Note 2) Average current consumption when A/D is on. (Note 1) * These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: When A/D is off, it will not consume any current other than minor leakage current. The power-down current spec includes any such leakage from the A/D module. 2: VREF current is from RA3 pin or VDD pin, whichever is selected as reference input. 3: The A/D conversion result never decreases with an increase in the Input Voltage, and has no missing codes. 1999 Microchip Technology Inc. Preliminary DS30569A-page 133 PIC16F870/871 FIGURE 14-13: A/D CONVERSION TIMING BSF ADCON0, GO 1 TCY (TOSC/2)(1) 131 Q4 130 132 A/D CLK 9 A/D DATA 8 ... 7 ... 2 1 0 NEW_DATA OLD_DATA ADRES ADIF GO DONE SAMPLING STOPPED SAMPLE Note 1: If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the SLEEP instruction to be executed. TABLE 14-10: A/D CONVERSION REQUIREMENTS Param No. 130 Sym Characteristic TAD A/D clock period Min Typ Max Units Standard(F) 1.6 -- -- s TOSC based, VREF 3.0V Extended(LF) 3.0 -- -- s TOSC based, VREF 2.0V Standard(F) 2.0 4.0 6.0 s A/D RC Mode Extended(LF) 3.0 6.0 9.0 s A/D RC Mode -- 12 TAD Note 2 40 -- s 10* -- -- s The minimum time is the amplifier settling time. This may be used if the "new" input voltage has not changed by more than 1 LSb (i.e., 20.0 mV @ 5.12V) from the last sampled voltage (as stated on CHOLD). -- TOSC/2 -- -- If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the SLEEP instruction to be executed. 131 TCNV Conversion time (not including S/H time) (Note 1) 132 TACQ Acquisition time 134 TGO Q4 to A/D clock start Conditions * These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. This specification ensured by design. Note 1: ADRES register may be read on the following TCY cycle. 2: See Section 10.1 for min conditions. DS30569A-page 134 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 15.0 DC AND AC CHARACTERISTICS GRAPHS AND TABLES The graphs and tables provided in this section are for design guidance and are not tested. In some graphs or tables, the data presented are outside specified operating range (i.e., outside specified VDD range). This is for information only and devices are ensured to operate properly only within the specified range. The data presented in this section is a statistical summary of data collected on units from different lots over a period of time and matrix samples. 'Typical' represents the mean of the distribution at 25C. 'Max' or 'min' represents (mean + 3) or (mean - 3) respectively, where is standard deviation, over the whole temperature range. Graphs and Tables not available at this time. 1999 Microchip Technology Inc. Preliminary DS30569A-page 135 PIC16F870/871 NOTES: DS30569A-page 136 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 16.0 PACKAGING INFORMATION 16.1 Package Marking Information 28-Lead PDIP (Skinny DIP) Example XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX YYWWNNN PIC16F870-I/SP 9910SAA 28-Lead SOIC Example XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX PIC16F870-I/SO 9910SAA YYWWNNN 28-Lead SSOP Example XXXXXXXXXXXX XXXXXXXXXXXX PIC16F870-I/SS 9910SAA YYWWNNN Legend: MM...M XX...X YY WW NNN Note: * Microchip part number information Customer specific information* Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line thus limiting the number of available characters for customer specific information. Standard OTP marking consists of Microchip part number, year code, week code, facility code, mask rev#, and assembly code. For OTP marking beyond this, certain price adders apply. Please check with your Microchip Sales Office. For QTP devices, any special marking adders are included in QTP price. 1999 Microchip Technology Inc. Preliminary DS30569A-page 137 PIC16F870/871 Package Marking Information (Cont'd) 40-Lead PDIP Example XXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXX AABBCDE PIC16F871-I/P 9912SAA 44-Lead TQFP Example XXXXXXXXXX XXXXXXXXXX XXXXXXXXXX AABBCDE PIC16F871 -I/PT 9911HAT 44-Lead PLCC Example PIC16F871 -I/L XXXXXXXXXX XXXXXXXXXX XXXXXXXXXX AABBCDE DS30569A-page 138 9903SAT Preliminary 1999 Microchip Technology Inc. PIC16F870/871 28-Lead Plastic Shrink Small Outline (SS) - 209 mil, 5.30 mm (SSOP) E E1 p D B 2 1 n A c A2 A1 L Units Dimension Limits n p MIN INCHES NOM 28 .026 .073 .068 .006 .309 .207 .402 .030 .007 4 .013 5 5 MAX MILLIMETERS* NOM MAX 28 0.65 1.73 1.85 1.98 1.63 1.73 1.83 0.05 0.15 0.25 7.59 7.85 8.10 5.11 5.25 5.38 10.06 10.20 10.34 0.56 0.75 0.94 0.10 0.18 0.25 0.00 101.60 203.20 0.25 0.32 0.38 0 5 10 0 5 10 MIN Number of Pins Pitch Overall Height A .068 .078 Molded Package Thickness A2 .064 .072 Standoff A1 .002 .010 Overall Width E .299 .319 Molded Package Width E1 .201 .212 Overall Length D .396 .407 Foot Length L .022 .037 c Lead Thickness .004 .010 Foot Angle 0 8 Lead Width B .010 .015 Mold Draft Angle Top 0 10 Mold Draft Angle Bottom 0 10 *Controlling Parameter Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MS-150 Drawing No. C04-073 1999 Microchip Technology Inc. Preliminary DS30569A-page 139 PIC16F870/871 28-Lead Skinny Plastic Dual In-line (SP) - 300 mil (PDIP) E1 D 2 n 1 E A2 A L c B1 A1 eB Units Number of Pins Pitch p B Dimension Limits n p INCHES* MIN NOM MILLIMETERS MAX MIN NOM 28 MAX 28 .100 2.54 Top to Seating Plane A .140 .150 .160 3.56 3.81 4.06 Molded Package Thickness A2 .125 .130 .135 3.18 3.30 3.43 Base to Seating Plane A1 .015 8.26 0.38 Shoulder to Shoulder Width E .300 .310 .325 7.62 7.87 Molded Package Width E1 .275 .285 .295 6.99 7.24 7.49 Overall Length D 1.345 1.365 1.385 34.16 34.67 35.18 Tip to Seating Plane L c .125 .130 .135 3.18 3.30 3.43 .008 .012 .015 0.20 0.29 0.38 1.65 Lead Thickness Upper Lead Width B1 .040 .053 .065 1.02 1.33 Lower Lead Width B .016 .019 .022 0.41 0.48 0.56 Overall Row Spacing eB .320 .350 .430 8.13 8.89 10.92 Mold Draft Angle Top Mold Draft Angle Bottom 5 10 15 5 10 15 5 10 15 5 10 15 *Controlling Parameter Notes: Dimension D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MO-095 Drawing No. C04-070 DS30569A-page 140 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 28-Lead Plastic Small Outline (SO) - Wide, 300 mil (SOIC) E E1 p D B 2 1 n h 45 c A2 A L Units Dimension Limits n p A1 MIN INCHES* NOM 28 .050 .099 .091 .008 .407 .295 .704 .020 .033 4 .011 .017 12 12 MAX MILLIMETERS NOM 28 1.27 2.36 2.50 2.24 2.31 0.10 0.20 10.01 10.34 7.32 7.49 17.65 17.87 0.25 0.50 0.41 0.84 0 4 0.23 0.28 0.36 0.42 0 12 0 12 MIN Number of Pins Pitch Overall Height A .093 .104 Molded Package Thickness A2 .088 .094 Standoff A1 .004 .012 Overall Width E .394 .420 Molded Package Width E1 .288 .299 Overall Length D .695 .712 Chamfer Distance h .010 .029 Foot Length L .016 .050 Foot Angle Top 0 8 c Lead Thickness .009 .013 Lead Width B .014 .020 Mold Draft Angle Top 0 15 Mold Draft Angle Bottom 0 15 *Controlling Parameter Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MS-013 Drawing No. C04-052 1999 Microchip Technology Inc. Preliminary MAX 2.64 2.39 0.30 10.67 7.59 18.08 0.74 1.27 8 0.33 0.51 15 15 DS30569A-page 141 PIC16F870/871 40-Lead Plastic Dual In-line (P) - 600 mil (PDIP) E1 D 2 1 n E A2 A L c B1 A1 eB p B Units Dimension Limits n p MIN INCHES* NOM 40 .100 .175 .150 MAX MILLIMETERS NOM 40 2.54 4.06 4.45 3.56 3.81 0.38 15.11 15.24 13.46 13.84 51.94 52.26 3.05 3.30 0.20 0.29 0.76 1.27 0.36 0.46 15.75 16.51 5 10 5 10 MIN Number of Pins Pitch Top to Seating Plane A .160 .190 Molded Package Thickness A2 .140 .160 Base to Seating Plane A1 .015 Shoulder to Shoulder Width E .595 .600 .625 Molded Package Width E1 .530 .545 .560 Overall Length D 2.045 2.058 2.065 Tip to Seating Plane L .120 .130 .135 c Lead Thickness .008 .012 .015 Upper Lead Width B1 .030 .050 .070 Lower Lead Width B .014 .018 .022 Overall Row Spacing eB .620 .650 .680 Mold Draft Angle Top 5 10 15 Mold Draft Angle Bottom 5 10 15 *Controlling Parameter Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MO-011 Drawing No. C04-016 DS30569A-page 142 Preliminary MAX 4.83 4.06 15.88 14.22 52.45 3.43 0.38 1.78 0.56 17.27 15 15 1999 Microchip Technology Inc. PIC16F870/871 44-Lead Plastic Thin Quad Flatpack (PT) 10x10x1 mm Body, 1.0/0.10 mm Lead Form (TQFP) E E1 #leads=n1 p D1 D 2 1 B n CH x 45 A c L A1 A2 (F) Units Dimension Limits n p MIN INCHES NOM 44 .031 11 .043 .039 .004 .024 .039 3.5 .472 .472 .394 .394 .006 .015 .035 10 10 MAX MILLIMETERS* NOM 44 0.80 11 1.00 1.10 0.95 1.00 0.05 0.10 0.45 0.60 1.00 0 3.5 11.75 12.00 11.75 12.00 9.90 10.00 9.90 10.00 0.09 0.15 0.30 0.38 0.64 0.89 5 10 5 10 MIN Number of Pins Pitch Pins per Side n1 Overall Height A .039 .047 Molded Package Thickness A2 .037 .041 Standoff A1 .002 .006 Foot Length L .018 .030 (F) Footprint (Reference) Foot Angle 0 7 Overall Width E .463 .482 Overall Length D .463 .482 Molded Package Width E1 .390 .398 Molded Package Length .390 .398 D1 c Lead Thickness .004 .008 Lead Width B .012 .017 Pin 1 Corner Chamfer CH .025 .045 Mold Draft Angle Top 5 15 Mold Draft Angle Bottom 5 15 *Controlling Parameter Notes: Dimensions D1 and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MS-026 Drawing No. C04-076 1999 Microchip Technology Inc. Preliminary MAX 1.20 1.05 0.15 0.75 7 12.25 12.25 10.10 10.10 0.20 0.44 1.14 15 15 DS30569A-page 143 PIC16F870/871 44-Lead Plastic Leaded Chip Carrier (L) - Square (PLCC) E E1 #leads=n1 D1 D n 1 2 CH1 x 45 CH2 x 45 A3 A2 35 A B1 B c E2 Units Dimension Limits n p A1 p D2 INCHES* NOM 44 .050 11 .165 .173 .145 .153 .028 .020 .024 .029 .040 .045 .000 .005 .685 .690 .685 .690 .650 .653 .650 .653 .590 .620 .590 .620 .008 .011 .026 .029 .013 .020 0 5 0 5 MIN MAX MILLIMETERS NOM 44 1.27 11 4.19 4.39 3.68 3.87 0.71 0.51 0.61 0.74 1.02 1.14 0.00 0.13 17.40 17.53 17.40 17.53 16.51 16.59 16.51 16.59 14.99 15.75 14.99 15.75 0.20 0.27 0.66 0.74 0.33 0.51 0 5 0 5 MIN Number of Pins Pitch Pins per Side n1 Overall Height A .180 .160 Molded Package Thickness A2 .035 Standoff A1 Side 1 Chamfer Height A3 .034 Corner Chamfer 1 CH1 .050 Corner Chamfer (others) CH2 .010 Overall Width E .695 Overall Length D .695 Molded Package Width E1 .656 Molded Package Length D1 .656 Footprint Width E2 .630 Footprint Length D2 .630 c Lead Thickness .013 Upper Lead Width B1 .032 Lower Lead Width B .021 Mold Draft Angle Top 10 Mold Draft Angle Bottom 10 *Controlling Parameter Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MO-047 Drawing No. C04-048 DS30569A-page 144 Preliminary MAX 4.57 4.06 0.89 0.86 1.27 0.25 17.65 17.65 16.66 16.66 16.00 16.00 0.33 0.81 0.53 10 10 1999 Microchip Technology Inc. PIC16F870/871 INDEX A A/D ..................................................................................... 79 ADCON0 Register ...................................................... 79 ADCON1 Register ...................................................... 80 ADIF bit ...................................................................... 81 Analog Input Model Block Diagram ............................ 83 Analog Port Pins ...................................... 7, 8, 9, 35, 36 Block Diagram ............................................................ 82 Configuring Analog Port Pins ..................................... 84 Configuring the Interrupt ............................................ 81 Configuring the Module .............................................. 81 Conversion Clock ....................................................... 84 Conversions ............................................................... 85 Delays ........................................................................ 83 Effects of a Reset ....................................................... 86 GO/DONE bit ............................................................. 81 Internal Sampling Switch (Rss) Impedence ............... 82 Operation During Sleep ............................................. 86 Sampling Requirements ............................................. 82 Source Impedence ..................................................... 82 Time Delays ............................................................... 83 Absolute Maximum Ratings ............................................. 119 ADRES Register s ........................................................ 13, 79 Application Notes AN552 (Implementing Wake-up on Key Strokes Using PIC16CXXX) .................................................... 29 AN556 (Table Reading Using PIC16CXX) ................. 24 Architecture PIC16F870 Block Diagram .......................................... 5 PIC16F871 Block Diagram .......................................... 6 Assembler MPASM Assembler .................................................. 113 B Banking, Data Memory ................................................ 11, 16 Block Diagrams A/D ............................................................................. 82 Analog Input Model .................................................... 83 Capture ...................................................................... 58 Compare .................................................................... 59 PWM .......................................................................... 59 Timer0/WDT Prescaler .............................................. 47 Timer2 ........................................................................ 55 USART Receive ......................................................... 69 USART Transmit ........................................................ 67 BOR. See Brown-out Reset BRGH bit ............................................................................ 65 Brown-out Reset (BOR) ................................... 89, 93, 95, 96 BOR Status (BOR Bit) ................................................ 23 C Capture/Compare/PWM Capture Block Diagram ................................................... 58 CCP1CON Register ........................................... 57 CCP1IF .............................................................. 58 Mode .................................................................. 58 Prescaler ............................................................ 58 CCP Timer Resources ............................................... 57 Compare Block Diagram ................................................... 59 Mode .................................................................. 59 Software Interrupt Mode .................................... 59 Special Event Trigger ........................................ 59 1999 Microchip Technology Inc. Special Trigger Output of CCP1 ........................ 59 Section ....................................................................... 57 Special Event Trigger and A/D Conversions ............. 59 Capture/Compare/PWM (CCP) CCP1 RC2/CCP1 Pin ................................................. 7, 8 CCP2 RC1/T1OSI/CCP2 Pin ..................................... 7, 8 PWM Block Diagram ................................................. 59 PWM Mode ................................................................ 59 CCP1CON ......................................................................... 15 CCP1M0 bit ....................................................................... 57 CCP1M1 bit ....................................................................... 57 CCP1M2 bit ....................................................................... 57 CCP1M3 bit ....................................................................... 57 CCP1X bit .......................................................................... 57 CCP1Y bit .......................................................................... 57 CCP2CON ......................................................................... 15 CCPR1H Register .................................................. 13, 15, 57 CCPR1L Register ........................................................ 15, 57 CCPR2H Register .............................................................. 15 CCPR2L Register .............................................................. 15 Code Examples Indirect Addressing .................................................... 24 Code Protection ......................................................... 89, 103 Computed GOTO ............................................................... 24 Configuration Bits .............................................................. 89 D Data Memory ..................................................................... 11 Bank Select (RP1:RP0 Bits) ................................ 11, 16 General Purpose Registers ....................................... 11 Register File Map ...................................................... 12 Special Function Registers ........................................ 13 DC Characteristics ........................................................... 121 Development Support ...................................................... 113 Device Overview .................................................................. 5 Direct Addressing .............................................................. 25 E Electrical Characteristics ................................................. 119 Errata ................................................................................... 4 F Firmware Instructions ...................................................... 105 FSR Register ................................................... 13, 14, 15, 24 I I/O Ports ............................................................................ 27 ID Locations ............................................................... 89, 103 In-Circuit Serial Programming (ICSP) ........................ 89, 104 INDF .................................................................................. 15 INDF Register ........................................................ 13, 14, 24 Indirect Addressing ...................................................... 24, 25 FSR Register ............................................................. 11 Instruction Format ............................................................ 105 Instruction Set .................................................................. 105 ADDLW .................................................................... 107 ADDWF ................................................................... 107 ANDLW .................................................................... 107 ANDWF ................................................................... 107 BCF ......................................................................... 107 BSF .......................................................................... 107 BTFSC ..................................................................... 108 BTFSS ..................................................................... 108 CALL ........................................................................ 108 CLRF ....................................................................... 108 Preliminary DS30569A-page 145 PIC16F870/871 CLRW ...................................................................... 108 CLRWDT .................................................................. 108 COMF ...................................................................... 109 DECF ....................................................................... 109 DECFSZ ................................................................... 109 GOTO ...................................................................... 109 INCF ......................................................................... 109 INCFSZ .................................................................... 109 IORLW ..................................................................... 110 IORWF ..................................................................... 110 MOVF ....................................................................... 110 MOVLW ................................................................... 110 MOVWF ................................................................... 110 NOP ......................................................................... 110 RETFIE .................................................................... 111 RETLW .................................................................... 111 RETURN .................................................................. 111 RLF .......................................................................... 111 RRF .......................................................................... 111 SLEEP ..................................................................... 111 SUBLW .................................................................... 112 SUBWF .................................................................... 112 SWAPF .................................................................... 112 XORLW .................................................................... 112 XORWF .................................................................... 112 Summary Table ........................................................ 106 INTCON ............................................................................. 15 INTCON Register ............................................................... 18 GIE Bit ........................................................................ 18 INTE Bit ...................................................................... 18 INTF Bit ...................................................................... 18 PEIE Bit ...................................................................... 18 RBIE Bit ..................................................................... 18 RBIF Bit ................................................................ 18, 29 T0IE Bit ...................................................................... 18 T0IF Bit ...................................................................... 18 Internal Sampling Switch (Rss) Impedence ....................... 82 Interrupt Sources .......................................................... 89, 99 Block Diagram ............................................................ 99 Interrupt on Change (RB7:RB4 ) ................................ 29 RB0/INT Pin, External ...................................... 7, 8, 100 TMR0 Overflow ........................................................ 100 USART Receive/Transmit Complete ......................... 63 Interrupts, Context Saving During .................................... 100 Interrupts, Enable Bits Global Interrupt Enable (GIE Bit) ......................... 18, 99 Interrupt on Change (RB7:RB4) Enable (RBIE Bit) ........................................................... 18, 100 Peripheral Interrupt Enable (PEIE Bit) ....................... 18 RB0/INT Enable (INTE Bit) ........................................ 18 TMR0 Overflow Enable (T0IE Bit) .............................. 18 Interrupts, Flag Bits Interrupt on Change (RB7:RB4) Flag (RBIF Bit) ..................................................... 18, 29, 100 RB0/INT Flag (INTF Bit) ............................................. 18 TMR0 Overflow Flag (T0IF Bit) .......................... 18, 100 K KeeLoq Evaluation and Programming Tools ................. 116 L Loading of PC .................................................................... 24 DS30569A-page 146 M Master Clear (MCLR) ....................................................... 7, 8 MCLR Reset, Normal Operation .................... 93, 95, 96 MCLR Reset, SLEEP ..................................... 93, 95, 96 Memory Organization Data Memory ............................................................. 11 Program Memory ....................................................... 11 MPLAB Integrated Development Environment Software . 113 O OPCODE Field Descriptions ............................................ 105 OPTION ............................................................................. 15 OPTION_REG Register ..................................................... 17 INTEDG Bit ................................................................ 17 PS2:PS0 Bits ............................................................. 17 PSA Bit ...................................................................... 17 RBPU Bit ................................................................... 17 T0CS Bit .................................................................... 17 T0SE Bit .................................................................... 17 OSC1/CLKIN Pin ............................................................. 7, 8 OSC2/CLKOUT Pin ......................................................... 7, 8 Oscillator Configuration ............................................... 89, 91 HS ........................................................................ 91, 95 LP ........................................................................ 91, 95 RC ................................................................. 91, 92, 95 XT ........................................................................ 91, 95 Oscillator, WDT ................................................................ 101 Output of TMR2 ................................................................. 55 P Packaging ........................................................................ 137 Paging, Program Memory ............................................ 11, 24 Parallel Slave Port (PSP) ......................................... 9, 33, 36 Block Diagram ........................................................... 36 RE0/RD/AN5 Pin ............................................. 9, 35, 36 RE1/WR/AN6 Pin ............................................. 9, 35, 36 RE2/CS/AN7 Pin .............................................. 9, 35, 36 Read Waveforms ....................................................... 37 Select (PSPMODE Bit) .................................. 33, 34, 36 Write Waveforms ....................................................... 37 PCL Register ................................................... 13, 14, 15, 24 PCLATH Register ............................................ 13, 14, 15, 24 PCON Register ...................................................... 15, 23, 94 BOR Bit ...................................................................... 23 POR Bit ...................................................................... 23 PIC16F876 Pinout Description ............................................ 7 PICDEM-1 Low-Cost PICmicro Demo Board .................. 115 PICDEM-2 Low-Cost PIC16CXX Demo Board ................ 115 PICDEM-3 Low-Cost PIC16CXXX Demo Board ............. 115 PICSTART Plus Entry Level Development System ...... 115 PIE1 Register ............................................................... 15, 19 PIE2 Register ............................................................... 15, 21 Pinout Descriptions PIC16F870 .................................................................. 7 PIC16F871 .................................................................. 8 PIR1 Register .................................................................... 20 PIR2 Register .................................................................... 22 POP ................................................................................... 24 PORTA ...................................................................... 7, 8, 15 Analog Port Pins ...................................................... 7, 8 Initialization ................................................................ 27 PORTA Register ........................................................ 27 RA3,RA0 and RA5 Port Pins ..................................... 27 RA4/T0CKI Pin .................................................. 7, 8, 27 RA5/AN4 Pin ........................................................... 7, 8 TRISA Register .......................................................... 27 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 PORTA Register ................................................................ 13 PORTB ....................................................................... 7, 8, 15 PORTB Register ........................................................ 29 Pull-up Enable (RBPU Bit) ......................................... 17 RB0/INT Edge Select (INTEDG Bit) ........................... 17 RB0/INT Pin, External ...................................... 7, 8, 100 RB3:RB0 Port Pins .................................................... 29 RB7:RB4 Interrupt on Change ................................. 100 RB7:RB4 Interrupt on Change Enable (RBIE Bit) ........................................................... 18, 100 RB7:RB4 Interrupt on Change Flag (RBIF Bit) ..................................................... 18, 29, 100 RB7:RB4 Port Pins .................................................... 29 TRISB Register .......................................................... 29 PORTB Register ................................................................ 13 PORTC ...................................................................... 7, 8, 15 Block Diagram ............................................................ 31 PORTC Register ........................................................ 31 RC0/T1OSO/T1CKI Pin ........................................... 7, 8 RC1/T1OSI/CCP2 Pin .............................................. 7, 8 RC2/CCP1 Pin ......................................................... 7, 8 RC3 Pin .................................................................... 7, 8 RC4 Pin .................................................................... 7, 8 RC5 Pin .................................................................... 7, 8 RC6/TX/CK Pin .................................................. 7, 8, 64 RC7/RX/DT Pin ............................................ 7, 8, 64, 65 TRISC Register .................................................... 31, 63 PORTC Register ................................................................ 13 PORTD .................................................................... 9, 15, 36 Block Diagram ............................................................ 33 Parallel Slave Port (PSP) Function ............................ 33 PORTD Register ........................................................ 33 TRISD Register .......................................................... 33 PORTD Register ................................................................ 13 PORTE ........................................................................... 9, 15 Analog Port Pins .............................................. 9, 35, 36 Block Diagram ............................................................ 34 Input Buffer Full Status (IBF Bit) ................................ 34 Input Buffer Overflow (IBOV Bit) ................................ 34 Output Buffer Full Status (OBF Bit) ............................ 34 PORTE Register ........................................................ 34 PSP Mode Select (PSPMODE Bit) ................ 33, 34, 36 RE0/RD/AN5 Pin .............................................. 9, 35, 36 RE1/WR/AN6 Pin ............................................. 9, 35, 36 RE2/CS/AN7 Pin .............................................. 9, 35, 36 TRISE Register .......................................................... 34 PORTE Register ................................................................ 13 Postscaler, WDT Assignment (PSA Bit) ................................................ 17 Rate Select (PS2:PS0 Bits) ....................................... 17 Power-down Mode. See SLEEP Power-on Reset (POR) .............................. 89, 93, 94, 95, 96 Oscillator Start-up Timer (OST) ........................... 89, 94 POR Status (POR Bit) ................................................ 23 Power Control (PCON) Register ................................ 94 Power-down (PD Bit) ........................................... 16, 93 Power-up Timer (PWRT) ..................................... 89, 94 Time-out (TO Bit) ................................................. 16, 93 Time-out Sequence on Power-up ........................ 97, 98 PR2 .................................................................................... 15 PR2 Register ................................................................ 14, 55 Prescaler, Timer0 Assignment (PSA Bit) ................................................ 17 Rate Select (PS2:PS0 Bits) ....................................... 17 PRO MATE II Universal Programmer ........................... 115 Product Identification System .......................................... 193 1999 Microchip Technology Inc. Program Counter Reset Conditions ....................................................... 95 Program Memory ............................................................... 11 Interrupt Vector .......................................................... 11 Paging ................................................................. 11, 24 Program Memory Map ............................................... 11 Reset Vector .............................................................. 11 Program Verification ........................................................ 103 Programming Pin (VPP) ................................................... 7, 8 Programming, Device Instructions ................................... 105 PUSH ................................................................................. 24 R RAM. See Data Memory RCREG .............................................................................. 15 RCSTA Register .......................................................... 15, 64 CREN Bit ................................................................... 64 FERR Bit .................................................................... 64 OERR Bit ................................................................... 64 RX9 Bit ...................................................................... 64 RX9D Bit .................................................................... 64 SPEN Bit .............................................................. 63, 64 SREN Bit ................................................................... 64 Register File ....................................................................... 11 Register File Map ............................................................... 12 Registers FSR Summary ........................................................... 15 INDF Summary .......................................................... 15 INTCON Summary .................................................... 15 OPTION Summary .................................................... 15 PCL Summary ........................................................... 15 PCLATH Summary .................................................... 15 PORTB Summary ...................................................... 15 STATUS Summary .................................................... 15 TMR0 Summary ........................................................ 15 TRISB Summary ........................................................ 15 Reset ........................................................................... 89, 93 Block Diagram ........................................................... 93 Reset Conditions for All Registers ............................. 96 Reset Conditions for PCON Register ........................ 95 Reset Conditions for Program Counter ..................... 95 Reset Conditions for STATUS Register .................... 95 S SEEVAL Evaluation and Programming System ........... 116 SLEEP ................................................................. 89, 93, 102 Software Simulator (MPLAB-SIM) ................................... 114 SPBRG .............................................................................. 15 SPBRG Register ................................................................ 14 Special Features of the CPU ............................................. 89 Special Function Registers ................................................ 13 Special Function Register Summary ......................... 13 Speed, Operating ................................................................ 1 Stack .................................................................................. 24 Overflows ................................................................... 24 Underflow .................................................................. 24 STATUS Register ........................................................ 15, 16 C Bit ........................................................................... 16 DC Bit ........................................................................ 16 IRP Bit ....................................................................... 16 PD Bit .................................................................. 16, 93 RP1:RP0 Bits ............................................................. 16 TO Bit .................................................................. 16, 93 Z Bit ........................................................................... 16 Preliminary DS30569A-page 147 PIC16F870/871 T T1CKPS0 bit ...................................................................... 51 T1CKPS1 bit ...................................................................... 51 T1CON ............................................................................... 15 T1CON Register ........................................................... 15, 51 T1OSCEN bit ..................................................................... 51 T1SYNC bit ........................................................................ 51 T2CKPS0 bit ...................................................................... 55 T2CKPS1 bit ...................................................................... 55 T2CON Register ........................................................... 15, 55 TAD ..................................................................................... 84 Timer0 Clock Source Edge Select (T0SE Bit) ........................ 17 Clock Source Select (T0CS Bit) ................................. 17 Overflow Enable (T0IE Bit) ........................................ 18 Overflow Flag (T0IF Bit) ..................................... 18, 100 Overflow Interrupt .................................................... 100 RA4/T0CKI Pin, External Clock ............................... 7, 8 Timer1 ................................................................................ 51 RC0/T1OSO/T1CKI Pin ........................................... 7, 8 RC1/T1OSI/CCP2 Pin .............................................. 7, 8 Timers Timer0 External Clock .................................................... 48 Interrupt .............................................................. 47 Prescaler ............................................................ 48 Prescaler Block Diagram ................................... 47 Section ............................................................... 47 T0CKI ................................................................. 48 Timer1 Asynchronous Counter Mode ............................ 53 Capacitor Selection ............................................ 53 Operation in Timer Mode ................................... 52 Oscillator ............................................................ 53 Prescaler ............................................................ 53 Resetting of Timer1 Registers ........................... 53 Resetting Timer1 using a CCP Trigger Output .. 53 Synchronized Counter Mode ............................. 52 T1CON ............................................................... 51 TMR1H ............................................................... 53 TMR1L ............................................................... 53 Timer2 Block Diagram .................................................... 55 Postscaler .......................................................... 55 Prescaler ............................................................ 55 T2CON ............................................................... 55 Timing Diagrams A/D Conversion ........................................................ 134 Brown-out Reset ...................................................... 128 Capture/Compare/PWM ........................................... 130 CLKOUT and I/O ...................................................... 127 Power-up Timer ....................................................... 128 Reset ........................................................................ 128 Start-up Timer .......................................................... 128 Time-out Sequence on Power-up ........................ 97, 98 Timer0 ...................................................................... 129 Timer1 ...................................................................... 129 USART Asynchronous Master Transmission ............. 68 USART Asynchronous Reception .............................. 69 USART Synchronous Receive ................................. 132 USART Synchronous Reception ................................ 75 USART Synchronous Transmission .................. 74, 132 USART, Asynchronous Reception ............................. 72 Wake-up from SLEEP via Interrupt .......................... 103 Watchdog Timer ....................................................... 128 TMR0 ................................................................................. 15 DS30569A-page 148 TMR0 Register ................................................................... 13 TMR1CS bit ....................................................................... 51 TMR1H .............................................................................. 15 TMR1H Register ................................................................ 13 TMR1L ............................................................................... 15 TMR1L Register ................................................................. 13 TMR1ON bit ....................................................................... 51 TMR2 ................................................................................. 15 TMR2 Register ................................................................... 13 TMR2ON bit ....................................................................... 55 TOUTPS0 bit ..................................................................... 55 TOUTPS1 bit ..................................................................... 55 TOUTPS2 bit ..................................................................... 55 TOUTPS3 bit ..................................................................... 55 TRISA ................................................................................ 15 TRISA Register .................................................................. 14 TRISB ................................................................................ 15 TRISB Register .................................................................. 14 TRISC ................................................................................ 15 TRISC Register .................................................................. 14 TRISD ................................................................................ 15 TRISD Register .................................................................. 14 TRISE ................................................................................ 15 TRISE Register ............................................................ 14, 34 IBF Bit ........................................................................ 34 IBOV Bit ..................................................................... 34 OBF Bit ...................................................................... 34 PSPMODE Bit ................................................ 33, 34, 36 TXREG .............................................................................. 15 TXSTA ............................................................................... 15 TXSTA Register ................................................................. 63 BRGH Bit ................................................................... 63 CSRC Bit ................................................................... 63 SYNC Bit ................................................................... 63 TRMT Bit .................................................................... 63 TX9 Bit ....................................................................... 63 TX9D Bit .................................................................... 63 TXEN Bit .................................................................... 63 U Universal Synchronous Asynchronous Receiver Transmitter (USART) Asynchronous Receiver Setting Up Reception ......................................... 71 Timing Diagram ................................................. 72 USART ............................................................................... 63 Asynchronous Mode .................................................. 67 Receive Block Diagram ..................................... 71 Asynchronous Receiver ............................................. 69 Asynchronous Reception ........................................... 70 Asynchronous Transmitter ......................................... 67 Baud Rate Generator (BRG) ..................................... 65 Baud Rate Formula ........................................... 65 Baud Rates, Asynchronous Mode (BRGH=0) ... 66 High Baud Rate Select (BRGH Bit) ................... 63 Sampling ............................................................ 65 Clock Source Select (CSRC Bit) ................................ 63 Continuous Receive Enable (CREN Bit) .................... 64 Framing Error (FERR Bit) .......................................... 64 Mode Select (SYNC Bit) ............................................ 63 Overrun Error (OERR Bit) .......................................... 64 RC6/TX/CK Pin ........................................................ 7, 8 RC7/RX/DT Pin ........................................................ 7, 8 RCSTA Register ........................................................ 64 Receive Block Diagram ............................................. 69 Receive Data, 9th bit (RX9D Bit) ............................... 64 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 Receive Enable, 9-bit (RX9 Bit) ................................. 64 Serial Port Enable (SPEN Bit) .............................. 63, 64 Single Receive Enable (SREN Bit) ............................ 64 Synchronous Master Mode ........................................ 73 Synchronous Master Reception ................................. 75 Synchronous Master Transmission ............................ 73 Synchronous Slave Mode .......................................... 76 Transmit Block Diagram ............................................. 67 Transmit Data, 9th Bit (TX9D) .................................... 63 Transmit Enable (TXEN Bit) ....................................... 63 Transmit Enable, Nine-bit (TX9 Bit) ........................... 63 Transmit Shift Register Status (TRMT Bit) ................. 63 TXSTA Register ......................................................... 63 W Wake-up from SLEEP ................................................ 89, 102 Interrupts .............................................................. 95, 96 MCLR Reset .............................................................. 96 Timing Diagram ........................................................ 103 WDT Reset ................................................................ 96 Watchdog Timer (WDT) ............................................. 89, 101 Block Diagram .......................................................... 101 Enable (WDTE Bit) ................................................... 101 Programming Considerations .................................. 101 RC Oscillator ............................................................ 101 Time-out Period ....................................................... 101 WDT Reset, Normal Operation ...................... 93, 95, 96 WDT Reset, SLEEP ....................................... 93, 95, 96 WWW, On-Line Support ...................................................... 4 1999 Microchip Technology Inc. Preliminary DS30569A-page 149 PIC16F870/871 NOTES: DS30569A-page 150 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 ON-LINE SUPPORT Systems Information and Upgrade Hot Line Microchip provides on-line support on the Microchip World Wide Web (WWW) site. The web site is used by Microchip as a means to make files and information easily available to customers. To view the site, the user must have access to the Internet and a web browser, such as Netscape or Microsoft Explorer. Files are also available for FTP download from our FTP site. The Systems Information and Upgrade Line provides system users a listing of the latest versions of all of Microchip's development systems software products. Plus, this line provides information on how customers can receive any currently available upgrade kits.The Hot Line Numbers are: 1-800-755-2345 for U.S. and most of Canada, and 1-480-786-7302 for the rest of the world. Connecting to the Microchip Internet Web Site 991103 The Microchip web site is available by using your favorite Internet browser to attach to: www.microchip.com The file transfer site is available by using an FTP service to connect to: ftp://ftp.microchip.com The web site and file transfer site provide a variety of services. Users may download files for the latest Development Tools, Data Sheets, Application Notes, User's Guides, Articles and Sample Programs. A variety of Microchip specific business information is also available, including listings of Microchip sales offices, distributors and factory representatives. Other data available for consideration is: * Latest Microchip Press Releases * Technical Support Section with Frequently Asked Questions * Design Tips * Device Errata * Job Postings * Microchip Consultant Program Member Listing * Links to other useful web sites related to Microchip Products * Conferences for products, Development Systems, technical information and more * Listing of seminars and events 1999 Microchip Technology Inc. Trademarks: The Microchip name, logo, PIC, PICmicro, PICSTART, PICMASTER, PRO MATE and MPLAB are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FlexROM and fuzzyLAB are trademarks and SQTP is a service mark of Microchip in the U.S.A. All other trademarks mentioned herein are the property of their respective companies. Preliminary DS30569A-page 151 PIC16F870/871 READER RESPONSE It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation can better serve you, please FAX your comments to the Technical Publications Manager at (480) 786-7578. Please list the following information, and use this outline to provide us with your comments about this Data Sheet. To: Technical Publications Manager RE: Reader Response Total Pages Sent From: Name Company Address City / State / ZIP / Country Telephone: (_______) _________ - _________ FAX: (______) _________ - _________ Application (optional): Would you like a reply? Device: PIC16F870/871 Y N Literature Number: DS30569A Questions: 1. What are the best features of this document? 2. How does this document meet your hardware and software development needs? 3. Do you find the organization of this data sheet easy to follow? If not, why? 4. What additions to the data sheet do you think would enhance the structure and subject? 5. What deletions from the data sheet could be made without affecting the overall usefulness? 6. Is there any incorrect or misleading information (what and where)? 7. How would you improve this document? 8. How would you improve our software, systems, and silicon products? DS30569A-page 152 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 PIC16F870/871 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. -X /XX XXX Device Temperature Range Package Pattern Examples: a) b) Device PIC16F870, PIC16F870T ;VDD range 4.0V to 5.5V PIC16F871, PIC16F871T ;VDD range 4.0V to 5.5V PIC16LF870X, PIC16LF870T;VDD range 2.0V to 5.5V PIC16LF871X, PIC16LF871T;VDD range 2.0V to 5.5V F LP T = Normal VDD limits = Extended VDD limits = In Tape and Reel - SOIC, SSOP, TQFP and PLCC packages only. Temperature Range 0C to blank(3) = I = -40C to Package PQ PT SO SP SS P L Pattern QTP, Code or Special Requirements (blank otherwise) = = = = = = = 70C +85C c) d) PIC16F870-I/SP 301 = Industrial temp., PDIP package, 20 MHz, normal VDD limits, QTP pattern #301. PIC16F871-I/PT = Industrial temp., TQFP package, 20 MHz, Extended VDD limits. PIC16F871-I/P = Industrial temp., PDIP package, 20 MHz, normal VDD limits. PIC16LF870-I/SS = Industrial temp., SSOP package, DC - 20MHz, extended VDD limits. (Commercial) (Industrial) MQFP (Metric PQFP) TQFP (Thin Quad Flatpack) SOIC Skinny plastic dip SSOP PDIP PLCC Sales and Support Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. 2. 3. Your local Microchip sales office The Microchip Corporate Literature Center U.S. FAX: (480) 786-7277 The Microchip Worldwide Site (www.microchip.com) Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. New Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products. 1999 Microchip Technology Inc. Preliminary DS30569A-page 153 PIC16F870/871 NOTES: DS30569A-page 154 Preliminary 1999 Microchip Technology Inc. PIC16F870/871 NOTES: 1999 Microchip Technology Inc. Preliminary DS30569A-page 155 Note the following details of the code protection feature on PICmicro(R) MCUs. * * * * * * The PICmicro family meets the specifications contained in the Microchip Data Sheet. Microchip believes that its family of PICmicro microcontrollers is one of the most secure products of its kind on the market today, when used in the intended manner and under normal conditions. There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the PICmicro microcontroller in a manner outside the operating specifications contained in the data sheet. The person doing so may be engaged in theft of intellectual property. Microchip is willing to work with the customer who is concerned about the integrity of their code. Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable". Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our product. If you have any further questions about this matter, please contact the local sales office nearest to you. Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip's products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, FilterLab, KEELOQ, microID, MPLAB, PIC, PICmicro, PICMASTER, PICSTART, PRO MATE, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. dsPIC, ECONOMONITOR, FanSense, FlexROM, fuzzyLAB, In-Circuit Serial Programming, ICSP, ICEPIC, microPort, Migratable Memory, MPASM, MPLIB, MPLINK, MPSIM, MXDEV, PICC, PICDEM, PICDEM.net, rfPIC, Select Mode and Total Endurance are trademarks of Microchip Technology Incorporated in the U.S.A. Serialized Quick Turn Programming (SQTP) is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. (c) 2002, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received QS-9000 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona in July 1999. The Company's quality system processes and procedures are QS-9000 compliant for its PICmicro(R) 8-bit MCUs, KEELOQ(R) code hopping devices, Serial EEPROMs and microperipheral products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001 certified. 2002 Microchip Technology Inc. M WORLDWIDE SALES AND SERVICE AMERICAS ASIA/PACIFIC Japan Corporate Office Australia 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: 480-792-7627 Web Address: http://www.microchip.com Microchip Technology Australia Pty Ltd Suite 22, 41 Rawson Street Epping 2121, NSW Australia Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 Microchip Technology Japan K.K. Benex S-1 6F 3-18-20, Shinyokohama Kohoku-Ku, Yokohama-shi Kanagawa, 222-0033, Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Rocky Mountain China - Beijing 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7966 Fax: 480-792-7456 Microchip Technology Consulting (Shanghai) Co., Ltd., Beijing Liaison Office Unit 915 Bei Hai Wan Tai Bldg. No. 6 Chaoyangmen Beidajie Beijing, 100027, No. China Tel: 86-10-85282100 Fax: 86-10-85282104 Atlanta 500 Sugar Mill Road, Suite 200B Atlanta, GA 30350 Tel: 770-640-0034 Fax: 770-640-0307 Boston 2 Lan Drive, Suite 120 Westford, MA 01886 Tel: 978-692-3848 Fax: 978-692-3821 Chicago 333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075 Dallas 4570 Westgrove Drive, Suite 160 Addison, TX 75001 Tel: 972-818-7423 Fax: 972-818-2924 Detroit Tri-Atria Office Building 32255 Northwestern Highway, Suite 190 Farmington Hills, MI 48334 Tel: 248-538-2250 Fax: 248-538-2260 Kokomo 2767 S. Albright Road Kokomo, Indiana 46902 Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles 18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 949-263-1888 Fax: 949-263-1338 China - Chengdu Microchip Technology Consulting (Shanghai) Co., Ltd., Chengdu Liaison Office Rm. 2401, 24th Floor, Ming Xing Financial Tower No. 88 TIDU Street Chengdu 610016, China Tel: 86-28-6766200 Fax: 86-28-6766599 China - Fuzhou Microchip Technology Consulting (Shanghai) Co., Ltd., Fuzhou Liaison Office Unit 28F, World Trade Plaza No. 71 Wusi Road Fuzhou 350001, China Tel: 86-591-7503506 Fax: 86-591-7503521 China - Shanghai Microchip Technology Consulting (Shanghai) Co., Ltd. Room 701, Bldg. B Far East International Plaza No. 317 Xian Xia Road Shanghai, 200051 Tel: 86-21-6275-5700 Fax: 86-21-6275-5060 China - Shenzhen 150 Motor Parkway, Suite 202 Hauppauge, NY 11788 Tel: 631-273-5305 Fax: 631-273-5335 Microchip Technology Consulting (Shanghai) Co., Ltd., Shenzhen Liaison Office Rm. 1315, 13/F, Shenzhen Kerry Centre, Renminnan Lu Shenzhen 518001, China Tel: 86-755-2350361 Fax: 86-755-2366086 San Jose Hong Kong Microchip Technology Inc. 2107 North First Street, Suite 590 San Jose, CA 95131 Tel: 408-436-7950 Fax: 408-436-7955 Microchip Technology Hongkong Ltd. Unit 901-6, Tower 2, Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 New York Toronto 6285 Northam Drive, Suite 108 Mississauga, Ontario L4V 1X5, Canada Tel: 905-673-0699 Fax: 905-673-6509 India Microchip Technology Inc. India Liaison Office Divyasree Chambers 1 Floor, Wing A (A3/A4) No. 11, O'Shaugnessey Road Bangalore, 560 025, India Tel: 91-80-2290061 Fax: 91-80-2290062 Korea Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea 135-882 Tel: 82-2-554-7200 Fax: 82-2-558-5934 Singapore Microchip Technology Singapore Pte Ltd. 200 Middle Road #07-02 Prime Centre Singapore, 188980 Tel: 65-334-8870 Fax: 65-334-8850 Taiwan Microchip Technology Taiwan 11F-3, No. 207 Tung Hua North Road Taipei, 105, Taiwan Tel: 886-2-2717-7175 Fax: 886-2-2545-0139 EUROPE Denmark Microchip Technology Nordic ApS Regus Business Centre Lautrup hoj 1-3 Ballerup DK-2750 Denmark Tel: 45 4420 9895 Fax: 45 4420 9910 France Microchip Technology SARL Parc d'Activite du Moulin de Massy 43 Rue du Saule Trapu Batiment A - ler Etage 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany Microchip Technology GmbH Gustav-Heinemann Ring 125 D-81739 Munich, Germany Tel: 49-89-627-144 0 Fax: 49-89-627-144-44 Italy Microchip Technology SRL Centro Direzionale Colleoni Palazzo Taurus 1 V. Le Colleoni 1 20041 Agrate Brianza Milan, Italy Tel: 39-039-65791-1 Fax: 39-039-6899883 United Kingdom Arizona Microchip Technology Ltd. 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44 118 921 5869 Fax: 44-118 921-5820 01/18/02 2002 Microchip Technology Inc.