INCH - POUND MIL-DTL-83723/79E 1 October 2010 SUPERSEDING MIL-DTL-83723/79D 20 October 2000 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, (CIRCULAR, ENVIRONMENT RESISTING), RECEPTACLE, (FLANGE MOUNT, BAYONET COUPLING, SOLDER PIN CONTACT), (SERIES III, CLASSES H, J, L, P AND Y) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83723. FIGURE 1. Dimensions and configurations. AMSC N/A FSC 5935 Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:04Z Check the source to verify that this is the current version before use. MIL-DTL-83723/79E FIGURE 1. Dimensions and configurations - Continued. 2 Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:04Z Check the source to verify that this is the current version before use. MIL-DTL-83723/79E Shell size A B 8 .812 .594 C dia .561 10 .937 .719 .696 12 1.031 .812 .875 14 1.125 .906 .935 16 1.250 .969 1.062 18 1.343 1.062 1.187 20 1.437 1.156 1.312 22 1.562 1.250 1.437 24 1.703 1.375 1.562 D dia .428 .433 .530 .535 .700 .705 .769 .774 .896 .901 1.002 1.007 1.127 1.132 1.252 1.257 1.377 1.382 E dia .312 F dia .500 G dia .120 .388 .562 .120 .558 .750 .120 .627 .812 .120 .772 .937 .120 .860 1.062 .120 .985 1.187 .120 1.110 1.312 .120 1.235 1.437 .149 FIGURE 1. Dimensions and configurations - Continued. 3 Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:04Z Check the source to verify that this is the current version before use. MIL-DTL-83723/79E Shell size P dia S +.005/ -.000 Panel cutout for C dia 8 .536 .531 .659 .654 .829 .824 .898 .893 1.025 1.020 1.131 1.126 1.256 1.251 1.381 1.376 1.506 1.501 .508 .630 .620 .758 .748 .923 .913 .990 .980 1.117 1.107 1.219 1.209 1.347 1.337 1.462 1.452 1.587 1.577 10 12 14 16 18 20 22 24 .636 .806 .875 1.002 1.108 1.233 1.358 1.483 Panel cutout for F dia .515 .505 .582 .572 .770 .760 .832 .822 .958 .948 1.082 1.072 1.202 1.192 1.332 1.322 1.452 1.442 CC .406 .443 .668 .668 .763 .862 1.108 1.204 1.388 FIGURE 1. Dimensions and configurations - Continued. 4 Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:04Z Check the source to verify that this is the current version before use. MIL-DTL-83723/79E Inches mm Inches .0025 .003 .004 .005 .010 .015 .018 .020 .022 .032 .052 .071 .072 .076 .078 .084 .089 .090 .094 .097 .101 .106 .108 .112 .125 .138 .144 .198 .204 .225 .259 .312 .330 .366 .376 0.065 0.08 0.10 0.13 0.25 0.38 0.48 0.51 0.56 0.81 1.32 1.80 1.83 1.93 1.98 2.13 2.26 2.29 2.39 2.46 2.57 2.69 2.74 2.84 3.18 3.51 3.66 5.03 5.18 5.72 6.58 7.92 8.38 9.30 9.55 .378 .380 .388 .392 .400 .406 .428 .433 .443 .490 .500 .505 .508 .515 .530 .531 .535 .536 .540 .558 .560 .561 .562 .572 .582 .594 .602 .620 .627 .630 .636 .654 .659 .668 .696 mm 9.60 9.65 9.86 9.96 10.16 10.31 10.87 11.00 11.25 12.45 12.70 12.83 12.90 13.08 13.46 13.49 13.51 13.61 13.72 14.17 14.22 14.25 14.27 14.53 14.78 15.09 15.29 15.75 15.93 16.00 16.15 16.61 16.74 16.97 17.68 Inches mm Inches mm Inches .700 .705 .719 .730 .748 .750 .758 .760 .763 .769 .770 .772 .774 .806 .812 .822 .824 .829 .832 .860 .862 .875 .890 .893 .896 .898 .900 .901 .906 .913 .918 .923 .935 .937 .948 17.78 17.92 18.26 18.54 19.00 19.05 19.25 19.30 19.38 19.53 19.56 19.61 19.66 20.47 20.62 20.88 20.93 21.06 21.13 21.84 21.98 22.23 22.61 22.68 22.76 22.81 22.86 22.89 23.01 23.19 23.32 23.44 23.75 23.80 24.08 .958 .969 .970 .980 .985 .988 .990 1.002 1.007 1.020 1.025 1.031 1.062 1.072 1.082 1.096 1.107 1.108 1.110 1.114 1.117 1.125 1.126 1.127 1.131 1.132 1.156 1.187 1.192 1.202 1.204 1.209 1.219 1.220 1.233 24.33 24.61 24.64 24.89 25.02 25.10 25.15 25.45 25.58 25.91 26.04 26.19 26.97 27.23 27.48 27.96 28.12 28.14 28.19 28.30 28.37 28.58 28.60 28.63 28.73 28.75 29.36 30.15 30.28 30.53 30.58 30.71 30.96 30.99 31.32 1.235 1.250 1.251 1.252 1.256 1.257 1.312 1.322 1.328 1.332 1.337 1.343 1.346 1.347 1.358 1.375 1.376 1.377 1.381 1.382 1.388 1.437 1.442 1.452 1.462 1.470 1.483 1.501 1.506 1.562 1.577 1.578 1.587 1.596 1.703 mm 31.37 31.75 31.78 31.80 31.90 31.93 33.32 33.58 33.73 33.83 33.96 34.11 34.19 34.21 34.49 34.93 34.95 34.98 35.08 35.10 35.26 36.50 36.63 36.88 37.13 37.34 37.67 38.13 38.25 39.67 40.06 40.08 40.31 40.54 43.26 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .005 inches (0.13 mm) for three place decimals, .01 inches (0.25 mm) for two place decimals and 1 for all angles. 4. Dimensions apply after plating. 5. Surface finish: 63 ( ) all over in accordance with ASME-B46.1, unless otherwise specified. 6. Remove all burrs and sharp edges .003 to .005 inches (0.076 to 0.127 mm) R. 7. Diameters to be concentric within .004 inches (0.102 mm) TIR. 8. Diameter in the same cross-sectional plane to be concentric with each other within .003 inches (0.076 mm) TIR. 9. See table I for contact cavities requiring this dimension. FIGURE 1. Dimensions and configurations - Continued. 5 Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:04Z Check the source to verify that this is the current version before use. MIL-DTL-83723/79E REQUIREMENTS: Dimensions and configuration: See figure 1. This connector mates with MIL-DTL-83723/75 and /77. For insert arrangements, see MIL-STD-1554 and table I. TABLE I. Insert arrangements requiring reduced diameters for raised seal barriers on contact cavities as indicated. Shell size Insert arrangements Contact cavities 8 03, 98 1, 2, and 3 10 06 1, 2, 3, 4, 5, and 6 Connector accessories: See SAE-AS85049. Part or Identifying Number (PIN) example: M83723/ 79 H 22 55 N Military designation Specification sheet number Class Shell size Insert arrangement Polarizing position Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-83723, this document references the following: MIL-DTL-83723/75 MIL-DTL-83723/77 MIL-STD-1554 ASME-B46.1 SAE-AS85049 6 Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:04Z Check the source to verify that this is the current version before use. MIL-DTL-83723/79E CONCLUDING MATERIAL Custodians: Army - CR Navy - AS Air Force - 85 DLA - CC Preparing activity: DLA - CC (Project 5935-2010-047) Review activities: Army - AR, MI Navy - EC Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https://assist.daps.dla.mil. 7 Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:04Z Check the source to verify that this is the current version before use.