MC33201, MC33202, MC33204, NCV33201, NCV33202, NCV33204 Low Voltage, Rail-to-Rail Operational Amplifiers www.onsemi.com The MC33201/2/4 family of operational amplifiers provide rail-to-rail operation on both the input and output. The inputs can be driven as high as 200 mV beyond the supply rails without phase reversal on the outputs, and the output can swing within 50 mV of each rail. This rail-to-rail operation enables the user to make full use of the supply voltage range available. It is designed to work at very low supply voltages ( 0.9 V) yet can operate with a supply of up to +12 V and ground. Output current boosting techniques provide a high output current capability while keeping the drain current of the amplifier to a minimum. Also, the combination of low noise and distortion with a high slew rate and drive capability make this an ideal amplifier for audio applications. PDIP-8 P, VP SUFFIX CASE 626 8 1 8 1 Features * Low Voltage, Single Supply Operation * * * * * * * * * * 8 (+1.8 V and Ground to +12 V and Ground) Input Voltage Range Includes both Supply Rails Output Voltage Swings within 50 mV of both Rails No Phase Reversal on the Output for Over-driven Input Signals High Output Current (ISC = 80 mA, Typ) Low Supply Current (ID = 0.9 mA, Typ) 600 W Output Drive Capability Extended Operating Temperature Ranges (-40 to +105C and -55 to +125C) Typical Gain Bandwidth Product = 2.2 MHz NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC-Q100 Qualified and PPAP Capable These Devices are Pb-Free and are RoHS Compliant 1 SOIC-8 D, VD SUFFIX CASE 751 Micro8] DM SUFFIX CASE 846A PDIP-14 P, VP SUFFIX CASE 646 14 1 14 SOIC-14 D, VD SUFFIX CASE 751A 1 14 1 TSSOP-14 DTB SUFFIX CASE 948G ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 10 of this data sheet. DEVICE MARKING INFORMATION See general marking information in the device marking section on page 11 of this data sheet. (c) Semiconductor Components Industries, LLC, 2014 July, 2018 - Rev. 18 1 Publication Order Number: MC33201/D MC33201, MC33202, MC33204, NCV33201, NCV33202, NCV33204 PIN CONNECTIONS MC33204 All Case Styles MC33201 All Case Styles NC 1 8 2 7 Output 1 1 NC 2 VCC Inputs 1 Inputs 3 6 Output VEE 4 5 NC 2 Inputs 1 1 3 VEE 4 4 13 12 11 5 10 6 2 3 Output 2 7 MC33202 All Case Styles Output 1 1 1 3 VCC 4 Inputs 2 (Top View) 14 Output 4 9 8 Inputs 4 VEE Inputs 3 Output 3 (Top View) 8 VCC 7 Output 2 6 2 Inputs 2 5 (Top View) VCC VCC VEE VCC Vin- Vout VCC Vin+ VEE This device contains 70 active transistors (each amplifier). Figure 1. Circuit Schematic (Each Amplifier) www.onsemi.com 2 MC33201, MC33202, MC33204, NCV33201, NCV33202, NCV33204 MAXIMUM RATINGS Rating Symbol Value Unit VS +13 V Input Differential Voltage Range VIDR Note 1 V Common Mode Input Voltage Range (Note 2) VCM VCC + 0.5 V to VEE - 0.5 V V Output Short Circuit Duration ts Note 3 sec Maximum Junction Temperature TJ +150 C Storage Temperature Tstg - 65 to +150 C Maximum Power Dissipation PD Note 3 mW Supply Voltage (VCC to VEE) DC ELECTRICAL CHARACTERISTICS (TA = 25C) Characteristic VCC = 2.0 V VCC = 3.3 V VCC = 5.0 V Input Offset Voltage VIO (max) MC33201, NCV33201V MC33202, NCV33202, V MC33204, NCV33204, V 8.0 10 12 8.0 10 12 6.0 8.0 10 Output Voltage Swing VOH (RL = 10 kW) VOL (RL = 10 kW) 1.9 0.10 3.15 0.15 4.85 0.15 Power Supply Current per Amplifier (ID) 1.125 1.125 1.125 Unit mV Vmin Vmax mA Specifications at VCC = 3.3 V are guaranteed by the 2.0 V and 5.0 V tests. VEE = GND. DC ELECTRICAL CHARACTERISTICS (VCC = + 5.0 V, VEE = Ground, TA = 25C, unless otherwise noted.) Figure Symbol Input Offset Voltage (VCM 0 V to 0.5 V, VCM 1.0 V to 5.0 V) MC33201/NCV33201V: TA = + 25C MC33201: TA = - 40 to +105C MC33201V/NCV33201V: TA = - 55 to +125C MC33202/NCV33202, V: TA = + 25C MC33202/NCV33202: TA = - 40 to +105C MC33202V/NCV33202V: TA = - 55 to +125C (Note 4) MC33204/NCV33204V: TA = + 25C MC33204: TA = - 40 to +105C MC33204V/NCV33204V: TA = - 55 to +125C (Note 4) 3 VIO Input Offset Voltage Temperature Coefficient (RS = 50 W) TA = - 40 to +105C TA = - 55 to +125C 4 Characteristic Input Bias Current (VCM = 0 V to 0.5 V, VCM = 1.0 V to 5.0 V) TA = + 25C TA = - 40 to +105C TA = - 55 to +125C 5, 6 DVIO/DT IIB Min Typ Max - - - - - - - - - - - - - - - - - - 6.0 9.0 13 8.0 11 14 10 13 17 - - 2.0 2.0 - - - - - 80 100 - 200 250 500 Unit mV mV/C nA Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. The differential input voltage of each amplifier is limited by two internal parallel back-to-back diodes. For additional differential input voltage range, use current limiting resistors in series with the input pins. 2. The input common mode voltage range is limited by internal diodes connected from the inputs to both supply rails. Therefore, the voltage on either input must not exceed either supply rail by more than 500 mV. 3. Power dissipation must be considered to ensure maximum junction temperature (TJ) is not exceeded. (See Figure 2) 4. All NCV devices are qualified for Automotive use. www.onsemi.com 3 MC33201, MC33202, MC33204, NCV33201, NCV33202, NCV33204 DC ELECTRICAL CHARACTERISTICS (cont.) (VCC = + 5.0 V, VEE = Ground, TA = 25C, unless otherwise noted.) Figure Symbol Input Offset Current (VCM = 0 V to 0.5 V, VCM = 1.0 V to 5.0 V) TA = + 25C TA = - 40 to +105C TA = - 55 to +125C - IIO Common Mode Input Voltage Range - VICR Large Signal Voltage Gain (VCC = + 5.0 V, VEE = - 5.0 V) RL = 10 kW RL = 600 W 7 AVOL Characteristic Output Voltage Swing (VID = 0.2 V) RL = 10 kW RL = 10 kW RL = 600 W RL = 600 W Min Typ Max - - - 5.0 10 - 50 100 200 VEE - VCC Unit nA V kV/V 50 25 300 250 - - VOH VOL VOH VOL 4.85 - 4.75 - 4.95 0.05 4.85 0.15 - 0.15 - 0.25 60 90 - 500 25 - 50 80 - - - 0.9 0.9 1.125 1.125 8, 9, 10 V Common Mode Rejection (Vin = 0 V to 5.0 V) 11 CMR Power Supply Rejection Ratio VCC/VEE = 5.0 V/GND to 3.0 V/GND 12 PSRR Output Short Circuit Current (Source and Sink) 13, 14 ISC Power Supply Current per Amplifier (VO = 0 V) TA = - 40 to +105C TA = - 55 to +125C 15 ID dB mV/V mA mA AC ELECTRICAL CHARACTERISTICS (VCC = + 5.0 V, VEE = Ground, TA = 25C, unless otherwise noted.) Characteristic Slew Rate (VS = 2.5 V, VO = - 2.0 V to + 2.0 V, RL = 2.0 kW, AV = +1.0) Figure Symbol 16, 26 SR Min Typ Max 0.5 1.0 - Unit V/ms Gain Bandwidth Product (f = 100 kHz) 17 GBW - 2.2 - MHz Gain Margin (RL = 600 W, CL = 0 pF) 20, 21, 22 AM - 12 - dB Phase Margin (RL = 600 W, CL = 0 pF) 20, 21, 22 OM - 65 - Deg 23 CS - 90 - dB BWP - 28 - kHz - - 0.002 0.008 - - - 100 - Rin - 200 - kW Cin - 8.0 - pF - - 25 20 - - nV/ Hz - - 0.8 0.2 - - Channel Separation (f = 1.0 Hz to 20 kHz, AV = 100) Power Bandwidth (VO = 4.0 Vpp, RL = 600 W, THD 1 %) 24 Total Harmonic Distortion (RL = 600 W, VO = 1.0 Vpp, AV = 1.0) f = 1.0 kHz f = 10 kHz Open Loop Output Impedance (VO = 0 V, f = 2.0 MHz, AV = 10) THD ZO Differential Input Resistance (VCM = 0 V) Differential Input Capacitance (VCM = 0 V) Equivalent Input Noise Voltage (RS = 100 W) f = 10 Hz f = 1.0 kHz 25 Equivalent Input Noise Current f = 10 Hz f = 1.0 kHz 25 www.onsemi.com 4 en in % W pA/ Hz 2500 40 PERCENTAGE OF AMPLIFIERS (%) PD(max) , MAXIMUM POWER DISSIPATION (mW) MC33201, MC33202, MC33204, NCV33201, NCV33202, NCV33204 8 and 14 Pin DIP Pkg 2000 TSSOP-14 Pkg 1500 SO-14 Pkg 1000 SOIC-8 Pkg 500 0 -55 -40 -25 0 25 50 85 TA, AMBIENT TEMPERATURE (C) 30 25 20 15 10 5.0 0 -10 -8.0 -6.0 -4.0 -2.0 0 2.0 4.0 6.0 VIO, INPUT OFFSET VOLTAGE (mV) 125 Figure 2. Maximum Power Dissipation versus Temperature I IB , INPUT BIAS CURRENT (nA) 30 160 120 20 10 0 -50 -40 -30 -20 -10 0 10 20 30 40 VCC = +5.0 V VEE = Gnd VCM = 0 V to 0.5 V 80 VCM > 1.0 V 40 0 -55 -40 -25 50 TCV , INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT (mV/C) IO A VOL , OPEN LOOP VOLTAGE GAIN (kV/V) 100 50 0 -50 -100 VCC = 12 V VEE = Gnd TA = 25C -200 0 2.0 4.0 6.0 8.0 10 VCM, INPUT COMMON MODE VOLTAGE (V) 25 70 85 125 Figure 5. Input Bias Current versus Temperature 150 -150 0 TA, AMBIENT TEMPERATURE (C) Figure 4. Input Offset Voltage Temperature Coefficient Distribution I IB , INPUT BIAS CURRENT (nA) 10 200 360 amplifiers tested from 3 (MC33204) wafer lots VCC = +5.0 V VEE = Gnd TA = 25C DIP Package 40 -250 8.0 Figure 3. Input Offset Voltage Distribution 50 PERCENTAGE OF AMPLIFIERS (%) 360 amplifiers tested from 3 (MC33204) wafer lots VCC = +5.0 V VEE = Gnd TA = 25C DIP Package 35 12 300 260 220 180 140 VCC = +5.0 V VEE = Gnd RL = 600 W DVO = 0.5 V to 4.5 V 100 -55 -40 -25 Figure 6. Input Bias Current versus Common Mode Voltage 0 25 70 85 TA, AMBIENT TEMPERATURE (C) 105 Figure 7. Open Loop Voltage Gain versus Temperature www.onsemi.com 5 125 MC33201, MC33202, MC33204, NCV33201, NCV33202, NCV33204 RL = 600 W TA = 25C 10 8.0 6.0 4.0 2.0 0 1.0 VCC VSAT, OUTPUT SATURATION VOLTAGE (V) VO, OUTPUT VOLTAGE (Vpp ) 12 2.0 3.0 4.0 5.0 VCC,VEE SUPPLY VOLTAGE (V) 6.0 TA = -55C TA = 125C VCC - 0.4 V TA = -55C CMR, COMMON MODE REJECTION (dB) VO, OUTPUT VOLTAGE (Vpp ) 6.0 VCC = +6.0 V VEE = -6.0 V RL = 600 W AV = +1.0 TA = 25C 5.0 60 40 VCC = +6.0 V VEE = -6.0 V TA = -55 to +125C 20 0 10 I SC , OUTPUT SHORT CIRCUIT CURRENT (mA) PSR, POWER SUPPLY REJECTION (dB) PSR+ 80 60 PSR40 VCC = +6.0 V VEE = -6.0 V TA = -55 to +125C 0 1.0 k 10 k f, FREQUENCY (Hz) 100 1.0 k 10 k f, FREQUENCY (Hz) 100 k 1.0 M Figure 11. Common Mode Rejection versus Frequency 100 100 VEE 20 15 80 1.0 M 120 10 10 IL, LOAD CURRENT (mA) 100 Figure 10. Output Voltage versus Frequency 20 VEE + 0.2 V Figure 9. Output Saturation Voltage versus Load Current 9.0 10 k 100 k f, FREQUENCY (Hz) TA = 25C TA = 125C 0 12 0 1.0 k VEE + 0.4 V VCC = +5.0 V VEE = -5.0 V Figure 8. Output Voltage Swing versus Supply Voltage 3.0 VCC - 0.2 V TA = 25C 100 k 1.0 M 100 Source 80 60 Sink 40 VCC = +6.0 V VEE = -6.0 V TA = 25C 20 0 0 1.0 2.0 3.0 4.0 5.0 Vout, OUTPUT VOLTAGE (V) Figure 12. Power Supply Rejection versus Frequency Figure 13. Output Short Circuit Current versus Output Voltage www.onsemi.com 6 6.0 I CC , SUPPLY CURRENT PER AMPLIFIER (mA) 150 125 VCC = +5.0 V VEE = Gnd 100 Source 75 Sink 50 25 0 -55 -40 -25 0 25 70 85 TA, AMBIENT TEMPERATURE (C) 105 125 2.0 1.6 TA = 125C 1.2 TA = 25C 0.8 TA = -55C 0.4 0 0 1.0 Figure 14. Output Short Circuit Current versus Temperature GBW, GAIN BANDWIDTH PRODUCT (MHz) +Slew Rate 1.0 -Slew Rate 0.5 25 70 85 105 0 -55 -40 -25 0 25 70 85 105 Figure 16. Slew Rate versus Temperature Figure 17. Gain Bandwidth Product versus Temperature 40 VS = 6.0 V TA = 25C RL = 600 W 80 30 120 1A 2A 10 A 1.0 TA, AMBIENT TEMPERATURE (C) 50 -30 10 k 2.0 TA, AMBIENT TEMPERATURE (C) 70 -10 VCC = +2.5 V VEE = -2.5 V f = 100 kHz 3.0 125 2B 1A - Phase, CL = 0 pF 1B - Gain, CL = 0 pF 2A - Phase, CL = 300 pF 2B - Gain, CL = 300 pF 100 k 1B 1.0 M 160 200 O , EXCESS PHASE (DEGREES) , OPEN LOOP VOLTAGE GAIN (dB) VOL 0 4.0 A VOL, OPEN LOOP VOLTAGE GAIN (dB) SR, SLEW RATE (V/ s) VCC = +2.5 V VEE = -2.5 V VO = 2.0 V 0 -55 -40 -25 6.0 Figure 15. Supply Current per Amplifier versus Supply Voltage with No Load 2.0 1.5 2.0 3.0 4.0 5.0 VCC, VEE, SUPPLY VOLTAGE (V) 70 30 120 2A 10 -10 160 1A - Phase, VS = 6.0 V 1B - Gain, VS = 6.0 V 2A - Phase, VS = 1.0 V 2B - Gain, VS = 1.0 V f, FREQUENCY (Hz) 100 k 1B 2B 200 1.0 M f, FREQUENCY (Hz) Figure 18. Voltage Gain and Phase versus Frequency Figure 19. Voltage Gain and Phase versus Frequency www.onsemi.com 7 80 1A -30 10 k 240 10 M 40 CL = 0 pF TA = 25C RL = 600 W 50 125 240 10 M O , EXCESS PHASE (DEGREES) I SC , OUTPUT SHORT CIRCUIT CURRENT (mA) MC33201, MC33202, MC33204, NCV33201, NCV33202, NCV33204 MC33201, MC33202, MC33204, NCV33201, NCV33202, NCV33204 75 50 50 40 30 VCC = +6.0 V VEE = -6.0 V RL = 600 W CL = 100 pF 40 30 20 20 10 10 Gain Margin 0 -55 -40 -25 0 25 70 85 105 O M , PHASE MARGIN (DEGREES) 60 A , GAIN MARGIN (dB) M O M , PHASE MARGIN (DEGREES) 60 60 60 VCC = +6.0 V VEE = -6.0 V TA = 25C 45 30 15 0 0 125 10 100 Gain Margin 12 10 40 8.0 30 6.0 20 4.0 10 2.0 0 10 THD, TOTAL HARMONIC DISTORTION (%) 14 10 1.0 0 1.0 k 100 AV = 10 60 VCC = +6.0 V VEE = -6.0 V VO = 8.0 Vpp TA = 25C 30 1.0 k 10 k f, FREQUENCY (Hz) Figure 22. Gain and Phase Margin versus Capacitive Load Figure 23. Channel Separation versus Frequency VCC = +5.0 V TA = 25C VO = 2.0 Vpp VEE = -5.0 V RL = 600 W AV = 100 AV = 10 0.01 0.001 10 90 CL, CAPACITIVE LOAD (pF) AV = 1000 0.1 AV = 100 120 0 100 AV = 1.0 100 1.0 k 10 k 100 k en , EQUIVALENT INPUT NOISE VOLTAGE (nV/ Hz) 50 0 100 k 150 CS, CHANNEL SEPARATION (dB) 60 10 k Figure 21. Gain and Phase Margin versus Differential Source Resistance 16 Phase Margin 1.0 k RT, DIFFERENTIAL SOURCE RESISTANCE (W) A , GAIN MARGIN (dB) M O M , PHASE MARGIN (DEGREES) 70 15 Gain Margin Figure 20. Gain and Phase Margin versus Temperature VCC = +6.0 V VEE = -6.0 V RL = 600 W AV = 100 TA = 25C 45 30 TA, AMBIENT TEMPERATURE (C) 80 75 Phase Margin A , GAIN MARGIN (dB) M 70 Phase Margin 50 5.0 VCC = +6.0 V VEE = -6.0 V TA = 25C 40 30 3.0 Noise Voltage 20 10 2.0 1.0 Noise Current 0 10 f, FREQUENCY (Hz) 100 1.0 k 10 k f, FREQUENCY (Hz) Figure 24. Total Harmonic Distortion versus Frequency Figure 25. Equivalent Input Noise Voltage and Current versus Frequency www.onsemi.com 8 4.0 0 100 k i n , INPUT REFERRED NOISE CURRENT (pA/ Hz) 70 MC33201, MC33202, MC33204, NCV33201, NCV33202, NCV33204 DETAILED OPERATING DESCRIPTION Circuit Information The MC33201/2/4 family of operational amplifiers are unique in their ability to swing rail-to-rail on both the input and the output with a completely bipolar design. This offers low noise, high output current capability and a wide common mode input voltage range even with low supply voltages. Operation is guaranteed over an extended temperature range and at supply voltages of 2.0 V, 3.3 V and 5.0 V and ground. Since the common mode input voltage range extends from VCC to VEE, it can be operated with either single or split voltage supplies. The MC33201/2/4 are guaranteed not to latch or phase reverse over the entire common mode range, however, the inputs should not be allowed to exceed maximum ratings. Rail-to-rail performance is achieved at the input of the amplifiers by using parallel NPN-PNP differential input stages. When the inputs are within 800 mV of the negative rail, the PNP stage is on. When the inputs are more than 800 mV greater than VEE, the NPN stage is on. This switching of input pairs will cause a reversal of input bias currents (see Figure 6). Also, slight differences in offset voltage may be noted between the NPN and PNP pairs. Cross-coupling techniques have been used to keep this change to a minimum. In addition to its rail-to-rail performance, the output stage is current boosted to provide 80 mA of output current, enabling the op amp to drive 600 W loads. Because of this high output current capability, care should be taken not to exceed the 150C maximum junction temperature. VCC = +6.0 V VEE = -6.0 V RL = 600 W CL = 100 pF TA = 25C VCC = +6.0 V VEE = -6.0 V RL = 600 W CL = 100 pF TA = 25C V , OUTPUT VOLTAGE (50 mV/DIV) O V , OUTPUT VOLTAGE (2.0 mV/DIV) O General Information t, TIME (10 ms/DIV) t, TIME (5.0 ms/DIV) V , OUTPUT VOLTAGE (2.0 V/DIV) O Figure 26. Noninverting Amplifier Slew Rate Figure 27. Small Signal Transient Response VCC = +6.0 V VEE = -6.0 V RL = 600 W CL = 100 pF AV = 1.0 TA = 25C t, TIME (10 ms/DIV) Figure 28. Large Signal Transient Response Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor packages must be the correct size to ensure proper solder connection interface between the board and the package. With the correct pad geometry, the packages will self-align when subjected to a solder reflow process. www.onsemi.com 9 MC33201, MC33202, MC33204, NCV33201, NCV33202, NCV33204 ORDERING INFORMATION Operational Amplifier Function Device MC33201DG MC33201DR2G Single Operating Temperature Range TA= -40 to +105C Package SOIC-8 (Pb-Free) MC33201VDG MC33201VDR2G Dual 2500 / Tape & Reel SOIC-8 (Pb-Free) TA= -40 to +105C NCV33202DMR2G* MC33202VDG MC33202VDR2G TA = -55 to 125C Micro-8 (Pb-Free) SOIC-8 (Pb-Free) SO-14 (Pb-Free) MC33204DG MC33204DTBG TA= -40 to +105C MC33204DTBR2G Quad MC33204VDR2G NCV33204DR2G* TSSOP-14 (Pb-Free) SO-14 (Pb-Free) MC33204VDG 2500 / Tape & Reel 4000 / Tape & Reel 98 Units / Rail 55 Units / Rail 2500 Units / Tape & Reel 96 Units / Rail 2500 Units / Tape & Reel 55 Units / Rail 2500 Units / Tape & Reel TA = -55 to 125C NCV33204DTBR2G* 98 Units / Rail 2500 / Tape & Reel NCV33202VDR2G* MC33204DR2G 2500 / Tape & Reel 2500 / Tape & Reel TA = -55 to 125C MC33202DG MC33202DMR2G 98 Units / Rail 98 Units / Rail NCV33201VDR2G MC33202DR2G Shipping TSSOP-14 (Pb-Free) 2500 Units / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC-Q100 Qualified and PPAP Capable. www.onsemi.com 10 MC33201, MC33202, MC33204, NCV33201, NCV33202, NCV33204 MARKING DIAGRAMS 8 1 8 3320x ALYW G 1 320xV ALYW G PDIP-8 VP SUFFIX CASE 626 PDIP-8 P SUFFIX CASE 626 SOIC-8 VD SUFFIX CASE 751 SOIC-8 D SUFFIX CASE 751 * 8 8 MC3320xP AWL YYWWG 14 MC33204VDG AWLYWW 1 * MC33204P AWLYYWWG 1 ** MC33204VP AWLYYWWG 1 MC33 204 ALYWG G 1 1 x = 1 or 2 A = Assembly Location WL, L = Wafer Lot YY, Y = Year WW, W = Work Week G = Pb-Free Package G = Pb-Free Package (Note: Microdot may be in either location) *This marking diagram applies to NCV3320xV **This marking diagram applies to NCV33202DMR2G 11 MC33204DG AWLYWW TSSOP-14 DTB SUFFIX CASE 948G 14 14 www.onsemi.com 14 1 PDIP-14 VP SUFFIX CASE 646 14 SO-14 D SUFFIX CASE 751A 3202 AYWG G 1 PDIP-14 P SUFFIX CASE 646 14 8 MC33202VP AWL YYWWG 1 SO-14 VD SUFFIX CASE 751A Micro-8 DM SUFFIX CASE 846A MC33 204V ALYWG G 1 * MC33201, MC33202, MC33204, NCV33201, NCV33202, NCV33204 PACKAGE DIMENSIONS PDIP-8 P, VP SUFFIX CASE 626-05 ISSUE N D A E H 8 5 E1 1 4 NOTE 8 b2 c B END VIEW TOP VIEW WITH LEADS CONSTRAINED NOTE 5 A2 A e/2 NOTE 3 L SEATING PLANE A1 C D1 M e 8X SIDE VIEW b 0.010 eB END VIEW M C A M B M NOTE 6 www.onsemi.com 12 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: INCHES. 3. DIMENSIONS A, A1 AND L ARE MEASURED WITH THE PACKAGE SEATED IN JEDEC SEATING PLANE GAUGE GS-3. 4. DIMENSIONS D, D1 AND E1 DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS ARE NOT TO EXCEED 0.10 INCH. 5. DIMENSION E IS MEASURED AT A POINT 0.015 BELOW DATUM PLANE H WITH THE LEADS CONSTRAINED PERPENDICULAR TO DATUM C. 6. DIMENSION E3 IS MEASURED AT THE LEAD TIPS WITH THE LEADS UNCONSTRAINED. 7. DATUM PLANE H IS COINCIDENT WITH THE BOTTOM OF THE LEADS, WHERE THE LEADS EXIT THE BODY. 8. PACKAGE CONTOUR IS OPTIONAL (ROUNDED OR SQUARE CORNERS). DIM A A1 A2 b b2 C D D1 E E1 e eB L M INCHES MIN MAX ---- 0.210 0.015 ---- 0.115 0.195 0.014 0.022 0.060 TYP 0.008 0.014 0.355 0.400 0.005 ---- 0.300 0.325 0.240 0.280 0.100 BSC ---- 0.430 0.115 0.150 ---- 10 MILLIMETERS MIN MAX --- 5.33 0.38 --- 2.92 4.95 0.35 0.56 1.52 TYP 0.20 0.36 9.02 10.16 0.13 --- 7.62 8.26 6.10 7.11 2.54 BSC --- 10.92 2.92 3.81 --- 10 MC33201, MC33202, MC33204, NCV33201, NCV33202, NCV33204 PACKAGE DIMENSIONS SOIC-8 NB CASE 751-07 ISSUE AK -X- NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751-01 THRU 751-06 ARE OBSOLETE. NEW STANDARD IS 751-07. A 8 5 S B 0.25 (0.010) M Y M 1 4 -Y- K G C N DIM A B C D G H J K M N S X 45 _ SEATING PLANE -Z- 0.10 (0.004) H D 0.25 (0.010) M Z Y S X M J S SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 13 MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 _ 8 _ 0.010 0.020 0.228 0.244 MC33201, MC33202, MC33204, NCV33201, NCV33202, NCV33204 PACKAGE DIMENSIONS Micro8 DM SUFFIX CASE 846A-02 ISSUE H D HE PIN 1 ID -T- NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. 846A-01 OBSOLETE, NEW STANDARD 846A-02. E e b 8 PL 0.08 (0.003) M T B S A S SEATING PLANE A 0.038 (0.0015) A1 MILLIMETERS NOM MAX -- 1.10 0.08 0.15 0.33 0.40 0.18 0.23 3.00 3.10 3.00 3.10 0.65 BSC 0.40 0.55 0.70 4.75 4.90 5.05 DIM A A1 b c D E e L HE MIN -- 0.05 0.25 0.13 2.90 2.90 L c SOLDERING FOOTPRINT* 1.04 8X 0.041 0.38 0.015 3.20 0.126 6X 8X 4.24 0.167 0.65 0.0256 5.28 0.208 SCALE 8:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 14 INCHES NOM -- 0.003 0.013 0.007 0.118 0.118 0.026 BSC 0.016 0.021 0.187 0.193 MIN -- 0.002 0.010 0.005 0.114 0.114 MAX 0.043 0.006 0.016 0.009 0.122 0.122 0.028 0.199 MC33201, MC33202, MC33204, NCV33201, NCV33202, NCV33204 PACKAGE DIMENSIONS PDIP-14 CASE 646-06 ISSUE R D 14 A 8 E H E1 1 NOTE 8 7 b2 c B TOP VIEW END VIEW WITH LEADS CONSTRAINED NOTE 5 A2 A NOTE 3 L SEATING PLANE A1 C D1 e M eB END VIEW 14X b SIDE VIEW 0.010 M C A M B M NOTE 6 www.onsemi.com 15 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: INCHES. 3. DIMENSIONS A, A1 AND L ARE MEASURED WITH THE PACKAGE SEATED IN JEDEC SEATING PLANE GAUGE GS-3. 4. DIMENSIONS D, D1 AND E1 DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS ARE NOT TO EXCEED 0.10 INCH. 5. DIMENSION E IS MEASURED AT A POINT 0.015 BELOW DATUM PLANE H WITH THE LEADS CONSTRAINED PERPENDICULAR TO DATUM C. 6. DIMENSION E3 IS MEASURED AT THE LEAD TIPS WITH THE LEADS UNCONSTRAINED. 7. DATUM PLANE H IS COINCIDENT WITH THE BOTTOM OF THE LEADS, WHERE THE LEADS EXIT THE BODY. 8. PACKAGE CONTOUR IS OPTIONAL (ROUNDED OR SQUARE CORNERS). DIM A A1 A2 b b2 C D D1 E E1 e eB L M INCHES MIN MAX ---- 0.210 0.015 ---- 0.115 0.195 0.014 0.022 0.060 TYP 0.008 0.014 0.735 0.775 0.005 ---- 0.300 0.325 0.240 0.280 0.100 BSC ---- 0.430 0.115 0.150 ---- 10 MILLIMETERS MIN MAX --- 5.33 0.38 --- 2.92 4.95 0.35 0.56 1.52 TYP 0.20 0.36 18.67 19.69 0.13 --- 7.62 8.26 6.10 7.11 2.54 BSC --- 10.92 2.92 3.81 --- 10 MC33201, MC33202, MC33204, NCV33201, NCV33202, NCV33204 PACKAGE DIMENSIONS SOIC-14 CASE 751A-03 ISSUE K D A B 14 8 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE PROTRUSION SHALL BE 0.13 TOTAL IN EXCESS OF AT MAXIMUM MATERIAL CONDITION. 4. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSIONS. 5. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. A3 E H L 1 0.25 M DETAIL A 7 B 13X M b 0.25 M C A S B S DETAIL A h A e DIM A A1 A3 b D E e H h L M X 45 _ M A1 C SEATING PLANE MILLIMETERS MIN MAX 1.35 1.75 0.10 0.25 0.19 0.25 0.35 0.49 8.55 8.75 3.80 4.00 1.27 BSC 5.80 6.20 0.25 0.50 0.40 1.25 0_ 7_ SOLDERING FOOTPRINT* 6.50 14X 1.18 1 1.27 PITCH 14X 0.58 DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 16 INCHES MIN MAX 0.054 0.068 0.004 0.010 0.008 0.010 0.014 0.019 0.337 0.344 0.150 0.157 0.050 BSC 0.228 0.244 0.010 0.019 0.016 0.049 0_ 7_ MC33201, MC33202, MC33204, NCV33201, NCV33202, NCV33204 PACKAGE DIMENSIONS TSSOP-14 CASE 948G ISSUE B 14X K REF 0.10 (0.004) 0.15 (0.006) T U M T U V S S N 2X 14 L/2 0.25 (0.010) 8 M B -U- L PIN 1 IDENT. N F 7 1 0.15 (0.006) T U NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. S S DETAIL E K A -V- EEE CCC CCC EEE CCC K1 J J1 SECTION N-N -W- C 0.10 (0.004) -T- SEATING PLANE D H G DETAIL E DIM A B C D F G H J J1 K K1 L M MILLIMETERS INCHES MIN MAX MIN MAX 4.90 5.10 0.193 0.200 4.30 4.50 0.169 0.177 --- 1.20 --- 0.047 0.05 0.15 0.002 0.006 0.50 0.75 0.020 0.030 0.65 BSC 0.026 BSC 0.50 0.60 0.020 0.024 0.09 0.20 0.004 0.008 0.09 0.16 0.004 0.006 0.19 0.30 0.007 0.012 0.19 0.25 0.007 0.010 6.40 BSC 0.252 BSC 0_ 8_ 0_ 8_ SOLDERING FOOTPRINT 7.06 1 0.65 PITCH 14X 0.36 14X 1.26 DIMENSIONS: MILLIMETERS Micro8 is a trademark of International Rectifier. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 www.onsemi.com 17 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC33201/D