®
INA141
1
INA141
INA141
Precision, Low Power, G = 10, 100
INSTRUMENTATION AMPLIFIER
®
FEATURES
●LOW OFFSET VOLTAGE: 50µV max
●LOW DRIFT: 0.5µV/°C max
●ACCURATE GAIN: ±0.05% at G = 10
●LOW INPUT BIAS CURRENT: 5nA max
●HIGH CMR: 117dB min
●INPUTS PROTECTED TO ±40V
●WIDE SUPPLY RANGE: ±2.25 to ±18V
●LOW QUIESCENT CURRENT: 750µA
●8-PIN PLASTIC DIP, SO-8
DESCRIPTION
The INA141 is a low power, general purpose instru-
mentation amplifier offering excellent accuracy. Its
versatile 3-op amp design and small size make it ideal
for a wide range of applications. Current-feedback
input circuitry provides wide bandwidth even at high
gain (200kHz at G = 100).
Simple pin connections set an accurate gain of 10 or
100V/V without external resistors. Internal input pro-
tection can withstand up to ±40V without damage.
The INA141 is laser trimmed for very low offset
voltage (50µV), drift (0.5µV/°C) and high common-
mode rejection (117dB at G = 100). It operates with
power supplies as low as ±2.25V, and quiescent
current is only 750µA—ideal for battery operated
systems.
The INA141 is available in 8-pin plastic DIP, and
SO-8 surface-mount packages, specified for the –40°C
to +85°C temperature range.
INA141
A
1
A
2
A
3
40kΩ40kΩ
40kΩ40kΩ
V
IN
2
1
8
3
6
5
V
IN
V+
V–
INA141
Ref
V
O
–
+
Over-Voltage
Protection
25kΩ
25kΩ
Over-Voltage
Protection
4
7
G = 10
or
G =100
252Ω
5050Ω
252Ω
APPLICATIONS
●BRIDGE AMPLIFIER
●THERMOCOUPLE AMPLIFIER
●RTD SENSOR AMPLIFIER
●MEDICAL INSTRUMENTATION
●DATA ACQUISITION
International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 • Twx: 910-952-1111
Internet: http://www.burr-brown.com/ • FAXLine: (800) 548-6133 (US/Canada Only) • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132
PDS-1297B
SBOS052
®
INA141 2
SPECIFICATIONS
At TA = +25°C, VS = ±15V, and RL = 10kΩ, unless otherwise noted.
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes
no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change
without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant
any BURR-BROWN product for use in life support devices and/or systems.
INA141P, U INA141PA, UA
PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS
INPUT
Offset Voltage, RTI G = 100 ±20 ±50 ✻±125 µV
G = 10 ±50 ±100 ✻±250 µV
vs Temperature G = 100 ±0.2 ±0.5 ✻±1.5 µV/°C
G = 10(2) ±0.5 ±2✻±2.5 µV/°C
vs Power Supply
V
S
= ±2.25 to ±18V, G = 100
±0.4 ±1✻±3µV/V
G = 10 ±2±10 ✻±20 µV/V
Long-Term Stability G = 100 0.2 ✻µV/mo
G = 10 0.5 ✻µV/mo
Impedance, Differential 1010 || 2 ✻Ω || pF
Common-Mode 1010 || 9 ✻Ω || pF
Common-Mode Voltage Range(1) VO = 0V (V+) – 2 (V+) – 1.4 ✻✻ V
(V–) + 2 (V–) + 1.7 ✻✻ V
Safe Input Voltage ±40 ✻V
Common-Mode Rejection VCM = ±13V, ∆RS = 1kΩ
G = 100 117 125 110 120 dB
G = 10 100 106 93 100 dB
BIAS CURRENT ±2±5✻±10 nA
vs Temperature ±30 ✻pA/°C
Offset Current ±1±5✻±10 nA
vs Temperature ±30 ✻pA/°C
NOISE VOLTAGE, RTI
f = 10Hz G = 100, RS = 0Ω10 ✻nV/√Hz
f = 100Hz 8 ✻nV/√Hz
f = 1kHz 8 ✻nV/√Hz
fB = 0.1Hz to 10Hz 0.2 ✻µVp-p
f = 10Hz G = 10, RS = 0Ω22 ✻nV/√Hz
f = 100Hz 13 ✻nV/√Hz
f = 1kHz 12 ✻nV/√Hz
fB = 0.1Hz to 10Hz 0.6 ✻µVp-p
Noise Current
f = 10Hz 0.9 ✻pA/√Hz
f = 1kHz 0.3 ✻pA/√Hz
fB = 0.1Hz to 10Hz 30 ✻pAp-p
GAIN
Gain Error VO = ±13.6V, G = 100 ±0.03 ±0.075 ✻±0.15 %
G = 10 ±0.01 ±0.05 ✻±0.15 %
Gain vs Temperature(2) G = 10, 100 ±2±10 ✻✻ppm/°C
Nonlinearity G = 100 ±0.0005 ±0.002 ✻±0.004 % of FSR
G = 10 ±0.0003 ±0.001 ✻±0.002 % of FSR
OUTPUT
Voltage: Positive RL = 10kΩ(V+) – 1.4 (V+) – 0.9 ✻✻ V
Negative RL = 10kΩ(V–) + 1.4 (V–) + 0.9 ✻✻ V
Load Capacitance Stability 1000 ✻pF
Short-Circuit Current +6/–15 ✻mA
FREQUENCY RESPONSE
Bandwidth, –3dB G = 100 200 ✻kHz
G = 10 1 ✻MHz
Slew Rate VO = ±10V, G = 10 4 ✻V/µs
Settling Time, 0.01% VO = ±5V, G = 100 9 ✻µs
G = 10 7 ✻µs
Overload Recovery 50% Overdrive 4 ✻µs
POWER SUPPLY
Voltage Range ±2.25 ±15 ±18 ✻✻ ✻V
Current, Total VIN = 0V ±750 ±800 ✻✻µA
TEMPERATURE RANGE
Specification –40 85 ✻✻°C
Operating –40 125 ✻✻°C
θ
JA 8-Pin DIP 80 ✻°C/W
SO-8 SOIC 150 ✻°C/W
✻ Specification same as INA141P, U.
NOTE: (1) Input common-mode range varies with output voltage—see typical curves. (2) Guaranteed by wafer test.
®
INA141
3
J
V
–IN
V
+IN
V–
J
V+
V
O
Ref
1
2
3
4
8
7
6
5
Top View
PIN CONFIGURATION
8-Pin DIP and SO-8
Supply Voltage .................................................................................. ±18V
Analog Input Voltage Range ............................................................. ±40V
Output Short-Circuit (to ground) .............................................. Continuous
Operating Temperature ................................................. –40°C to +125°C
Storage Temperature ..................................................... –40°C to +125°C
Junction Temperature.................................................................... +150°C
Lead Temperature (soldering, 10s)............................................... +300°C
ABSOLUTE MAXIMUM RATINGS
ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with ap-
propriate precautions. Failure to observe proper handling and
installation procedures can cause damage.
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
ORDERING INFORMATION
PACKAGE
DRAWING TEMPERATURE
PRODUCT PACKAGE NUMBER(1) RANGE
INA141PA 8-Pin Plastic DIP 006 –40°C to +85°C
INA141P 8-Pin Plastic DIP 006 –40°C to +85°C
INA141UA SO-8 Surface-Mount 182 –40°C to +85°C
INA141U SO-8 Surface-Mount 182 –40°C to +85°C
NOTE: (1) For detailed drawing and dimension table, please see end of data
sheet, or Appendix C of Burr-Brown IC Data Book.
®
INA141 4
TYPICAL PERFORMANCE CURVES
At TA = +25°C and VS = ±15V, unless otherwise noted.
GAIN vs FREQUENCY
60
50
40
30
20
10
0
–10
–20
Gain (dB)
Frequency (Hz)
1k 10k 100k 1M 10M
G = 100V/V
G = 10V/V
POSITIVE POWER SUPPLY REJECTION
vs FREQUENCY
Frequency (Hz)
Power Supply Rejection (dB)
140
120
100
80
60
40
20
010 100 1k 10k 100k 1M
G = 100V/V
G = 10V/V
INPUT COMMON-MODE RANGE
vs OUTPUT VOLTAGE, VS = ±5, ±2.5V
Output Voltage (V)
Common-Mode Voltage (V)
–5
5
4
3
2
1
0
–1
–2
–3
–4
–5 –4 –3 –2 –1 0 1 2 3 4 5
VS = ±5V
VS = ±2.5V
COMMON-MODE REJECTION vs FREQUENCY
Frequency (Hz)
Common-Mode Rejection (dB)
10 100 10k 1M1k
140
120
100
80
60
40
20
0100k
G = 10V/V
G = 100V/V
NEGATIVE POWER SUPPLY REJECTION
vs FREQUENCY
Frequency (Hz)
Power Supply Rejection (dB)
140
120
100
80
60
40
20
010 100 1k 10k 100k 1M
G = 100V/V
G = 10V/V
INPUT COMMON-MODE RANGE
vs OUTPUT VOLTAGE, V
S
= ±15V
Output Voltage (V)
Common-Mode Voltage (V)
–15 –10 0 5 15–5
15
10
5
0
–5
–10
–15 10
V
D/2
–
+
–
+
V
CM
V
O
V
D/2
Ref
–15V
+15V
+
®
INA141
5
INPUT OFFSET VOLTAGE WARM-UP
10
8
6
4
2
0
–2
–4
–6
–8
–10 0100 200 300 400 500
Time (µs)
Input Offset Voltage Change (µV)
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C and VS = ±15V, unless otherwise noted.
OUTPUT VOLTAGE SWING
vs OUTPUT CURRENT
(V+)
(V+)–0.4
(V+)–0.8
(V+)–1.2
(V+)+1.2
(V–)+0.8
(V–)+0.4
V– 01234
Output Current (mA)
Output Voltage (V)
INPUT- REFERRED NOISE vs FREQUENCY
Frequency (Hz)
Input-Referred Voltage Noise (nV/√ Hz)
110 1k100
1k
100
10
110k
G = 10V/V
100
10
1
0.1
Input Bias Current Noise (pA/√ Hz)
Current Noise
G = 100V/V
INPUT OVER-VOLTAGE V/I CHARACTERISTICS
5
4
3
2
1
0
–1
–2
–3
–4
–5
Input Current (mA)
Input Voltage (V)
–50 –40 –30 –20 –10 10 20 30 40050
G = 10V/V
G = 10V/V
G = 100V/V
G = 100V/V V
IN
I
IN
–15V
+15V
INA141
Flat region represents
normal linear operation.
QUIESCENT CURRENT and SLEW RATE
vs TEMPERATURE
Temperature (°C)
Quiescent Current (µA)
0.9
0.85
0.8
0.75
0.7
0.65
6
5
4
3
2
1
–75 –50 –25 0 25 50 75 100 125
Slew Rate (V/µs)
IQ
Slew Rate
INPUT BIAS CURRENT vs TEMPERATURE
2
1
0
–1
–2–75 –50 –25 0 25 50 75 100 125
Temperature (°C)
Input Bias Current (nA)
I
OS
I
B
Typical I
B
Range
±2nA at 25°C
®
INA141 6
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C and VS = ±15V, unless otherwise noted.
OUTPUT VOLTAGE SWING
vs POWER SUPPLY VOLTAGE
V+
(V+)–0.4
(V+)–0.8
(V+)–1.2
(V–)+1.2
(V–)+0.8
(V–)+0.4
V– 0 5 10 15 20
Power Supply Voltage (V)
Output Voltage Swing (V)
+25°C +85°C
–40°C
+25°C
–40°C
+85°C
R
L
= 10kΩ
+85°C
–40°C
SHORT-CIRCUIT OUTPUT CURRENT
vs TEMPERATURE
18
16
14
12
10
8
6
4
2
0–75 –50 –25 0 25 50 75 100 125
Temperature (°C)
Short-Circuit Current (mA)
–I
SC
+I
SC
MAXIMUM OUTPUT VOLTAGE vs FREQUENCY
Frequency (Hz)
Peak-to-Peak Output Voltage (Vpp)
30
25
20
15
10
5
01k 10k 100k 1M
G = 10, 100
TOTAL HARMONIC DISTORTION + NOISE
vs FREQUENCY
Frequency (Hz)
THD+N (%)
100 1k 10k
1
0.1
0.01
0.001 100k
V
O
= 1Vrms
G = 10V/V
R
L
= 100kΩ
G = 100, R
L
= 100kΩ
R
L
= 10kΩ
500kHz Measurement
Bandwidth
Dashed Portion
is noise limited.
®
INA141
7
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C and VS = ±15V, unless otherwise noted.
G = 10
G = 100
G = 10
G = 100
5µs/div5µs/div
LARGE-SIGNAL STEP RESPONSE
SMALL-SIGNAL STEP RESPONSE
VOLTAGE NOISE 0.1 to 10Hz
INPUT-REFERRED, G = 100
1s/div
0.1µV/div
20mV/div 5V/div
®
INA141 8
APPLICATION INFORMATION
Figure 1 shows the basic connections required for operation
of the INA141. Applications with noisy or high impedance
power supplies may require decoupling capacitors close to
the device pins as shown.
The output is referred to the output reference (Ref) terminal
which is normally grounded. This must be a low-impedance
connection to assure good common-mode rejection. A resis-
tance of 8Ω in series with the Ref pin will cause a typical
device to degrade to approximately 80dB CMR (G = 1).
SETTING THE GAIN
Gain is selected with a jumper connection as shown in
Figure 1. G = 10V/V with no jumper installed. With a
jumper installed, G = 100V/V. To preserve good gain
accuracy, this jumper must have low series resistance. A
resistance of 0.5Ω in series with the jumper will decrease the
gain by 0.1%.
Internal resistor ratios are laser trimmed to assure excellent
gain accuracy. Actual resistor values can vary by approxi-
mately ±25% from the nominal values shown.
Gains between 10 and 100 can be achieved by connecting an
external resistor to the jumper pins. This is not recom-
mended, however, because the ±25% variation of internal
resistor values makes the required external resistor value
uncertain. A companion model, INA128, features accurately
trimmed internal resistors so that gains from 1 to 10,000 can
be set with an external resistor.
DYNAMIC PERFORMANCE
The typical performance curve “Gain vs Frequency” shows
that, despite its low quiescent current, the INA141 achieves
wide bandwidth, even at G = 100. This is due to the current-
feedback topology of the INA141. Settling time also re-
mains excellent at G = 100.
NOISE PERFORMANCE
The INA141 provides very low noise in most applications.
Low frequency noise is approximately 0.2µVp-p measured
from 0.1 to 10Hz (G = 100). This provides dramatically
improved noise when compared to state-of-the-art chopper-
stabilized amplifiers.
FIGURE 1. Basic Connections.
A1
A2
A36
40kΩ40kΩ
40kΩ40kΩ
7
4
3
8
1
2
VIN
VIN
V+
V–
INA141
–
+5
Over-Voltage
Protection
25kΩ
25kΩ
Over-Voltage
Protection
Load
VO = G • (VIN – VIN)
+–
0.1µF
0.1µF
+
–
VO
Also drawn in simplified form:
INA141
Ref
VO
VIN
–
VIN
+
Ref
G = 10
(no connection)
or
G = 100
(connect jumper)
252Ω
5050Ω
252Ω
®
INA141
9
FIGURE 3. Providing an Input Common-Mode Current Path.
OFFSET TRIMMING
The INA141 is laser trimmed for low offset voltage and
offset voltage drift. Most applications require no external
offset adjustment. Figure 2 shows an optional circuit for
trimming the output offset voltage. The voltage applied to
Ref terminal is summed with the output. The op amp buffer
provides low impedance at the Ref terminal to preserve good
common-mode rejection.
FIGURE 2. Optional Trimming of Output Offset Voltage.
INPUT BIAS CURRENT RETURN PATH
The input impedance of the INA141 is extremely high—
approximately 1010Ω. However, a path must be provided for
the input bias current of both inputs. This input bias current
is approximately ±2nA. High input impedance means that
this input bias current changes very little with varying input
voltage.
Input circuitry must provide a path for this input bias current
for proper operation. Figure 3 shows various provisions for
an input bias current path. Without a bias current path, the
inputs will float to a potential which exceeds the common-
mode range of the INA141 and the input amplifiers will
saturate.
If the differential source resistance is low, the bias current
return path can be connected to one input (see the thermo-
couple example in Figure 3). With higher source impedance,
using two equal resistors provides a balanced input with
possible advantages of lower input offset voltage due to bias
current and better high-frequency common-mode rejection.
INPUT COMMON-MODE RANGE
The linear input voltage range of the input circuitry of the
INA141 is from approximately 1.4V below the positive
supply voltage to 1.7V above the negative supply. As a
differential input voltage causes the output voltage to in-
crease, however, the linear input range will be limited by the
output voltage swing of amplifiers A1 and A2. So the linear
common-mode input range is related to the output voltage of
the complete amplifier. This behavior also depends on sup-
ply voltage—see performance curves “Input Common-Mode
Range vs Output Voltage”.
Input overload can produce an output voltage that appears
normal. For example, if an input overload condition drives
both input amplifiers to their positive output swing limit, the
difference voltage measured by the output amplifier will be
near zero. The output of the INA141 will be near 0V even
though both inputs are overloaded.
LOW VOLTAGE OPERATION
The INA141 can be operated on power supplies as low as
±2.25V. Performance remains excellent with power supplies
ranging from ±2.25V to ±18V. Most parameters vary only
slightly through this supply voltage range—see Typical
Performance Curves. Operation at very low supply voltage
requires careful attention to assure that the input voltages
remain within their linear range. Voltage swing require-
ments of internal nodes limit the input common-mode range
with low power supply voltage. Typical performance curves,
“Input Common-Mode Range vs Output Voltage” show the
range of linear operation for ±15V, ±5, and ±2.5V supplies.
INPUT PROTECTION
The inputs of the INA141 are individually protected for
voltages up to ±40V. For example, a condition of –40V on
one input and +40V on the other input will not cause
damage. Internal circuitry on each input provides low series
impedance under normal signal conditions. To provide
equivalent protection, series input resistors would contribute
excessive noise. If the input is overloaded, the protection
circuitry limits the input current to a safe value of approxi-
mately 1.5 to 5mA. The typical performance curve “Input
Bias Current vs Common-Mode Input Voltage” shows this
input current limit behavior. The inputs are protected even if
the power supplies are disconnected or turned off.
10kΩ
OPA177
±10mV
Adjustment Range
100Ω
100Ω
100µA
1/2 REF200
100µA
1/2 REF200
V+
V–
INA141
Ref
V
O
V
IN
–
V
IN
+
47kΩ47kΩ
10kΩ
Microphone,
Hydrophone
etc.
Thermocouple
Center-tap provides
bias current return.
INA141
INA141
INA141
®
INA141 10
REF102
R
2
R
1
R
3
Pt100
Cu
Cu
V+
K
6
10.0V
4
2
INA141 V
O
Ref
100Ω = Pt100 at 0°C
FIGURE 4. ECG Amplifier With Right-Leg Drive.
FIGURE 5. Bridge Amplifier.
FIGURE 7. Thermocouple Amplifier With RTD Cold-
Junction Compensation.
SEEBECK
ISA COEFFICIENT
TYPE MATERIAL (µV/°C) R1, R2
E + Chromel 58.5 66.5kΩ
– Constantan
J + Iron 50.2 76.8kΩ
– Constantan
K + Chromel 39.4 97.6kΩ
– Alumel
T + Copper 38.0 102kΩ
– Constantan
INA141 V
O
C
1
0.1µF
OPA602
Ref R
1
1MΩ
f
–3dB
= 1
2πR
1
C
1
= 1.59Hz
V
IN
+
–
FIGURE 6. AC-Coupled Instrumentation Amplifier.
INA141
I
B
R
1
V
IN
–
+
A
1
I
O
Load
I
O
= • G
V
IN
R
1
Ref
A1IB Error
OPA177 ±1.5nA
OPA131 50pA
OPA602 ±1pA
OPA128 ±75fA
FIGURE 8. Differential Voltage to Current Converter.
INA141 V
O
LA
RL
RA
10kΩ
Ref G = 10
20kΩ20kΩ
V
G
1/4
OPA4131
390kΩ
390kΩ
1/4
OPA4131
OPA4131
1/4
OPA4131
1/4
300Ω
+5V
2.5V – ∆V
2.5V + ∆V
+15V
–15V
INA141 V
O
Ref
PACKAGING INFORMATION
Orderable Device Status (1) Package
Type Package
Drawing Pins Package
Qty Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
INA141P OBSOLETE PDIP P 8 TBD Call TI Call TI
INA141PA OBSOLETE PDIP P 8 TBD Call TI Call TI
INA141U ACTIVE SOIC D 8 75 Green (RoHS &
no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA141U/2K5 ACTIVE SOIC D 8 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA141U/2K5E4 ACTIVE SOIC D 8 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA141UA ACTIVE SOIC D 8 75 Green (RoHS &
no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA141UA/2K5 ACTIVE SOIC D 8 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA141UA/2K5E4 ACTIVE SOIC D 8 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA141UAE4 ACTIVE SOIC D 8 75 Green (RoHS &
no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA141UAG4 ACTIVE SOIC D 8 75 Green (RoHS &
no Sb/Br) CU NIPDAU Level-3-260C-168 HR
INA141UG4 ACTIVE SOIC D 8 75 Green (RoHS &
no Sb/Br) CU NIPDAU Level-3-260C-168 HR
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
PACKAGE OPTION ADDENDUM
www.ti.com 16-Apr-2009
Addendum-Page 1
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0 (mm) B0 (mm) K0 (mm) P1
(mm) W
(mm) Pin1
Quadrant
INA141U/2K5 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
INA141UA/2K5 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 11-Mar-2008
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
INA141U/2K5 SOIC D 8 2500 346.0 346.0 29.0
INA141UA/2K5 SOIC D 8 2500 346.0 346.0 29.0
PACKAGE MATERIALS INFORMATION
www.ti.com 11-Mar-2008
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,and other changes to its products and services at any time and to discontinue any product or service without notice. Customers shouldobtain the latest relevant information before placing orders and should verify that such information is current and complete. All products aresold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standardwarranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except wheremandated by government requirements, testing of all parameters of each product is not necessarily performed.TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products andapplications using TI components. To minimize the risks associated with customer products and applications, customers should provideadequate design and operating safeguards.TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Informationpublished by TI regarding third-party products or services does not constitute a license from TI to use such products or services or awarranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectualproperty of the third party, or a license from TI under the patents or other intellectual property of TI.Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompaniedby all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptivebusiness practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additionalrestrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids allexpress and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is notresponsible or liable for any such statements.TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonablybe expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governingsuch use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, andacknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their productsand any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may beprovided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products insuch safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products arespecifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet militaryspecifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely atthe Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products aredesignated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designatedproducts in automotive applications, TI will not be responsible for any failure to meet such requirements.Following are URLs where you can obtain information on other Texas Instruments products and application solutions:Products ApplicationsAmplifiers amplifier.ti.com Audio www.ti.com/audioData Converters dataconverter.ti.com Automotive www.ti.com/automotiveDLP® Products www.dlp.com Broadband www.ti.com/broadbandDSP dsp.ti.com Digital Control www.ti.com/digitalcontrolClocks and Timers www.ti.com/clocks Medical www.ti.com/medicalInterface interface.ti.com Military www.ti.com/militaryLogic logic.ti.com Optical Networking www.ti.com/opticalnetworkPower Mgmt power.ti.com Security www.ti.com/securityMicrocontrollers microcontroller.ti.com Telephony www.ti.com/telephonyRFID www.ti-rfid.com Video & Imaging www.ti.com/videoRF/IF and ZigBee® Solutions www.ti.com/lprf Wireless www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2009, Texas Instruments Incorporated