LED..A62X62W Series Area Lights LED Area Lights for use with PresencePLUS(R) Pro sensors Features *Low-cost, compact area lights for PresencePLUS Pro sensor. See Banner's Web site (www.bannerengineering.com) for a complete lighting tutorial. *Solid-state LED matrix; continuous or strobed operation is selectable via sensor software. Red or Infrared LED models White, Green, or Blue LED models *Direct connection to PresencePLUS Pro or to an external power supply using 3 discrete wires. * Two bracket options available. Models Models Ambient Light Filter Kit Color LEDIA62X62W Infrared, 940 nm FLTI (included with IR lights) LEDRA62X62W Visible Red, 630 nm FLTR (included with LEDAPFKS) LEDWA62X62W White, All Visible FLTB or FLTG LEDBA62X62W Blue, 464 to 475 nm FLTB LEDGA62X62W Green, 520 to 540 nm FLTG Polarizing Filter Kit -- LEDAPFKS Specifications Light Source LED, see Models table above for wave lengths Illumination High-intensity area light Supply Voltage and Current Infrared: 24V dc @ 150 mA max. Connections PVC-jacketed 3-conductor 2 m (6.5') attached cable Construction Low-carbon steel with black zinc plating, acrylic window Useful Life 10,000 hours (LED ON time). When operated within specifications, output will decrease less than 30% after 10,000 hours and less than 50% (less than 40% for red and IR models) after 20,000 hours. Operating Conditions Temperature: 0 to +50 C (+32 to 122 F) Cleaning Instructions Regularly remove any dust, dirt, or fingerprints from the light source. 1. Blow off dust using anti-static compressed air. 2. If necessary, use a lens cloth and lens cleaner or window cleaner to wipe off remaining debris. Do not use any other chemicals for cleaning. All other colors: 24V dc @ 200 mA max. Relative humidity: 90% at 50C (non-condensing) max. Wiring Table Area Light Wire PresencePLUS Pro Controller Terminal Block External Power Supply (Strobed) External Power Supply (Continuous) Brown Pin 1 (+V*) +V +V Blue Pin 2 (-V*) White Printed in USA -V +5V dc -V Pin 4 (strobe) 02/07 -V OFF ON -V P/N 121779 rev. B LED..A62X62W Series Area Lights 62 x 62 Models 64.2 mm (2.53") 55.9 mm (2.2") 66.7 mm (2.63") 32 mm (1.26") 14.7 mm (0.58") 66.7 mm (2.63") 4.2 mm (0.17") 55.9 mm (2.2") 1/4- 20 PEM Nut Figure 1. Area light dimensions Installing the Area Light NOTE: Before installing this area light it is recommended that an ambient light filter be installed behind the lens. The filter improves image quality by reducing unwanted ambient light. Sensing Shiny Surfaces To eliminate direct reflections without using polarizing filters, angle the sensor approximately 15 (or more) from perpendicular to a shiny surface. Polarizing Kit If it is necessary to mount the camera at a 90 angle to a shiny surface, the polarizing filter kit provides filters for both the LED area light and sensor to reduce the negative effects of strong, direct light reflections. The red filter kit (FLTR) is included with the polarizing kit. When light colors other than red are used, discard the red filter in the polarizing kit and use the proper filter listed on page 1. The polarizing filters reduce the amount of light returned to the sensor. Mounting Brackets SMBVLA62X62S * Inline bracket * 14 gauge steel, black zinc-plated SMBVLA62X62RA * Right-angle bracket * 14 gauge steel, black zinc-plated Clearance for 1/4 - 20 screw (Included) Clearance for 1/4 - 20 screw (Included) 21.2 mm (0.84") 63.5 mm (2.50") 63.5 mm (2.50") 7.6 mm (0.30") 53.3 mm (2.10") 53.3 mm (2.10") 25.4 mm (1.0") 8.4 mm (0.33") 25.4 mm (1.0") 38.1 mm (1.50") 1.9 mm (0.07") Clearance for M6 (1/4 - 20) hardware (Hardware not included) 59.2 mm (2.33") 8.4 mm (0.33") 38.1 mm (1.50") 1.9 mm (0.07") Clearance for M6 (1/4 - 20) hardware (Hardware not included) 59.2 mm (2.33") 38.1 mm (1.50") 25.4 mm (1.0") 67.3 mm (2.65") 19.1 mm (0.75") 6.4 mm (0.25") 67.3 mm (2.65") WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. This warranty does not cover damage or liability for the improper application of Banner products. This warranty is in lieu of any other warranty either expressed or implied. P/N 121779 rev. B Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN 55441 * Phone: 763.544.3164 * www.bannerengineering.com * sensors@bannerengineering.com