Multisupply Supervisor/Sequencer with ADC and Temperature Monitoring ADM1063 FEATURES For more information about the ADM1063 register map, refer to the AN-698 Application Note at www.analog.com. FUNCTIONAL BLOCK DIAGRAM D1P D1N D2P D2N TEMP SENSOR REFIN REFOUT REFGND SDA SCL A1 VREF INTERNAL DIODE MUX A0 SMBus INTERFACE 12-BIT SAR ADC EEPROM CLOSED-LOOP MARGINING SYSTEM VX1 VX2 VX3 VX4 VX5 DUALFUNCTION INPUTS CONFIGURABLE OUTPUT DRIVERS (LOGIC INPUTS OR SFDs) (HV CAPABLE OF DRIVING GATES OF N-FET) PDO1 PDO2 PDO3 PDO4 PDO5 PDO6 SEQUENCING ENGINE VP1 VP2 VP3 VP4 PROGRAMMABLE RESET GENERATORS (SFDs) VH CONFIGURABLE OUTPUT DRIVERS PDO7 (LV CAPABLE OF DRIVING LOGIC SIGNALS) PDO9 AGND PDO8 PDO10 PDOGND VDD ARBITRATOR ADM1063 VCCP GND VDDCAP 04632-001 Complete supervisory and sequencing solution for up to 10 supplies 10 supply fault detectors enable supervision of supplies to <0.5% accuracy at all voltages at 25C <1.0% accuracy across all voltages and temperatures 5 selectable input attenuators allow supervision of supplies to 14.4 V on VH 6 V on VP1 to VP4 (VPx) 5 dual-function inputs, VX1 to VX5 (VXx) High impedance input to supply fault detector with thresholds between 0.573 V and 1.375 V General-purpose logic input 10 programmable driver outputs, PDO1 to PDO10 (PDOx) Open-collector with external pull-up Push/pull output, driven to VDDCAP or VPx Open collector with weak pull-up to VDDCAP or VPx Internally charge-pumped high drive for use with external N-FET (PDO1 to PDO6 only) Sequencing engine (SE) implements state machine control of PDOx outputs State changes conditional on input events Enables complex control of boards Power-up and power-down sequence control Fault event handling Interrupt generation on warnings Watchdog function can be integrated in SE Program software control of sequencing through SMBus Complete voltage margining solution for 6 voltage rails 12-bit ADC for readback of all supervised voltages 1 internal and 2 external temperature sensors Reference input (REFIN) has 2 input options Driven directly from 2.048 V (0.25%) REFOUT pin More accurate external reference for improved ADC performance Device powered by the highest of VPx, VH for improved redundancy User EEPROM: 256 bytes Industry-standard, 2-wire bus interface (SMBus) Guaranteed PDO low with VH, VPx = 1.2 V Available in 40-lead, 6 mm x 6 mm LFCSP and 48-lead, 7 mm x 7 mm TQFP packages Figure 1. APPLICATIONS Central office systems Servers/routers Multivoltage system line cards DSP/FPGA supply sequencing In-circuit testing of margined supplies GENERAL DESCRIPTION The ADM1063 is a configurable supervisory/sequencing device that offers a single-chip solution for supply monitoring and sequencing in multiple supply systems. In addition to these functions, the ADM1063 integrates a 12-bit ADC that can be used to accurately read back up to 12 separate voltages. The device also provides up to 10 programmable inputs for monitoring undervoltage faults, overvoltage faults, or out-ofwindow faults on up to 10 supplies. In addition, 10 programmable outputs can be used as logic enables. Six of these programmable outputs can provide up to a 12 V output for driving the gate of an N-FET that can be placed in the path of a supply. Rev. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2005-2011 Analog Devices, Inc. All rights reserved. ADM1063 TABLE OF CONTENTS Features .............................................................................................. 1 Overview ..................................................................................... 17 Functional Block Diagram .............................................................. 1 Warnings...................................................................................... 17 Applications....................................................................................... 1 SMBus Jump (Unconditional Jump)........................................ 17 General Description ......................................................................... 1 Sequencing Engine Application Example ............................... 18 Revision History ............................................................................... 2 Fault and Status Reporting........................................................ 19 Detailed Block Diagram .................................................................. 3 Voltage Readback............................................................................ 20 Specifications..................................................................................... 4 Supply Supervision with the ADC ........................................... 20 Pin Configurations and Function Descriptions ........................... 7 Temperature Measurement System.............................................. 21 Absolute Maximum Ratings............................................................ 9 Remote Temperature Measurement ........................................ 21 Thermal Resistance ...................................................................... 9 Applications Diagram .................................................................... 23 ESD Caution.................................................................................. 9 Communicating with the ADM1063........................................... 24 Typical Performance Characteristics ........................................... 10 Configuration Download at Power-Up................................... 24 Powering the ADM1063 ................................................................ 13 Updating the Configuration ..................................................... 24 Inputs................................................................................................ 14 Updating the Sequencing Engine............................................. 25 Supply Supervision..................................................................... 14 Internal Registers........................................................................ 25 Programming the Supply Fault Detectors............................... 14 EEPROM ..................................................................................... 25 Input Comparator Hysteresis.................................................... 14 Serial Bus Interface..................................................................... 25 Input Glitch Filtering ................................................................. 15 SMBus Protocols for RAM and EEPROM.............................. 27 Supply Supervision with VXx Inputs....................................... 15 Write Operations ........................................................................ 27 VXx Pins as Digital Inputs ........................................................ 15 Read Operations......................................................................... 29 Outputs ............................................................................................ 16 Outline Dimensions ....................................................................... 30 Supply Sequencing Through Configurable Output Drivers. 16 Ordering Guide .......................................................................... 31 Default Output Configuration.................................................. 16 Sequencing Engine ......................................................................... 17 REVISION HISTORY 7/11--Rev. B to Rev. C Changes to Serial Bus Timing Parameter in Table 1.................... 4 Added Endnote 4 in Table 1............................................................ 4 Changes to Figure 3.......................................................................... 7 Added Exposed Pad Notation to Outline Dimensions ............. 30 Changes to Ordering Guide .......................................................... 31 5/08--Rev. A to Rev. B Changes to Table 1............................................................................ 4 Changes to Powering the ADM1063 Section ............................. 13 Changes to Table 5.......................................................................... 14 Changes to Default Output Configuration Section ................... 16 Changes to Sequence Detector Section ....................................... 19 Changes to Temperature Measurement System Section ........... 21 Changes to Table 10........................................................................ 22 Changes to Configuration Download at Power-Up Section..... 24 Changes to Table 11........................................................................ 25 Changes to Figure 44 and Error Correction Section ................. 29 Changes to Ordering Guide .......................................................... 31 12/06--Rev. 0 to Rev. A Updated Format..................................................................Universal Changes to Features ..........................................................................1 Changes to Figure 2...........................................................................3 Changes to Table 1.............................................................................4 Changes to Table 2.............................................................................7 Changes to Absolute Maximum Ratings Section..........................9 Deleted Figure 17 to Figure 19...................................................... 12 Changes to Programming the Supply Fault Detectors Section... 14 Changes to Table 6.......................................................................... 14 Changes to Outputs Section.......................................................... 16 Changes to Fault Reporting Section ............................................ 20 Deleted Supply Margining Section .............................................. 21 Changes to Table 9.......................................................................... 21 Changes to Identifying the ADM1063 on the SMBus Section .................................................................... 28 Changes to Figure 34 and Figure 35............................................. 30 4/05--Revision 0: Initial Version Rev. C | Page 2 of 32 ADM1063 This design enables very flexible sequencing of the outputs based on the condition of the inputs. Temperature measurement is possible with the ADM1063. The device contains one internal temperature sensor and two pairs of differential inputs for remote thermal diodes. These are measured by the 12-bit ADC. The device is controlled via configuration data that can be programmed into an EEPROM. The entire configuration can be programmed using an intuitive GUI-based software package provided by Analog Devices, Inc. The logical core of the device is a sequencing engine. This statemachine-based construction provides up to 63 different states. DETAILED BLOCK DIAGRAM REFIN REFOUT D1P D1N D2P D2N REFGND SDA SCL A1 A0 ADM1063 TEMP SENSOR INTERNAL DIODE VREF 12-BIT SAR ADC SMBus INTERFACE DEVICE CONTROLLER GPI SIGNAL CONDITIONING VX1 OSC EEPROM CONFIGURABLE OUTPUT DRIVER (HV) SFD PDO1 PDO2 VX2 PDO3 VX3 PDO4 VX4 PDO5 GPI SIGNAL CONDITIONING VX5 VP1 SFD SELECTABLE ATTENUATOR SEQUENCING ENGINE SFD VP2 CONFIGURABLE OUTPUT DRIVER (HV) PDO6 CONFIGURABLE OUTPUT DRIVER (LV) PDO7 VP3 PDO8 VP4 PDO9 VH SELECTABLE ATTENUATOR SFD PDO10 PDOGND AGND REG 5.25V CHARGE PUMP VDD ARBITRATOR GND 04632-002 VDDCAP CONFIGURABLE OUTPUT DRIVER (LV) VCCP Figure 2. Rev. C | Page 3 of 32 ADM1063 SPECIFICATIONS VH = 3.0 V to 14.4 V 1 , VPx = 3.0 V to 6.0 V1, TA = -40C to +85C, unless otherwise noted. Table 1. Parameter POWER SUPPLY ARBITRATION VH, VPx VPx VH VDDCAP CVDDCAP POWER SUPPLY Supply Current, IVH, IVPx Additional Currents All PDO FET Drivers On Min Typ Max Unit Test Conditions/Comments 4.75 6.0 14.4 5.4 V V V V F Minimum supply required on one of VH, VPx Maximum VDDCAP = 5.1 V, typical VDDCAP = 4.75 V Regulated LDO output Minimum recommended decoupling capacitance 4.2 6 mA VDDCAP = 4.75 V, PDO1 to PDO10 off, ADC off mA 3.0 2.7 10 1 1 10 mA mA VDDCAP = 4.75 V, PDO1 to PDO6 loaded with 1 A each, PDO7 to PDO10 off Maximum additional load that can be drawn from all PDO pull-ups to VDDCAP Running round-robin loop 1 ms duration only, VDDCAP = 3 V 52 0.05 k % Midrange and high range Current Available from VDDCAP ADC Supply Current EEPROM Erase Current SUPPLY FAULT DETECTORS VH Pin Input Impedance Input Attenuator Error Detection Ranges High Range Midrange VPx Pins Input Impedance Input Attenuator Error Detection Ranges Midrange Low Range Ultralow Range VXx Pins Input Impedance Detection Range Ultralow Range Absolute Accuracy 2 6 2.5 52 0.05 2.5 1.25 0.573 Input Reference Voltage on REFIN Pin, VREFIN Resolution INL Gain Error 6 3 1.375 1 V V k % Low range and midrange V V V No input attenuation error M 0.573 Threshold Resolution Digital Glitch Filter ANALOG-TO-DIGITAL CONVERTER Signal Range 14.4 6 mA 1.375 1 8 0 100 V % Bits s s 0 VREFIN V 2.5 0.05 V Bits LSB % 2.048 12 Rev. C | Page 4 of 32 No input attenuation error VREF error + DAC nonlinearity + comparator offset error + input attenuation error Minimum programmable filter length Maximum programmable filter length The ADC can convert signals presented to the VH, VPx, and VXx pins; VPx and VH input signals are attenuated depending on the selected range; a signal at the pin corresponding to the selected range is from 0.573 V to 1.375 V at the ADC input Endpoint corrected, VREFIN = 2.048 V VREFIN = 2.048 V ADM1063 Parameter Conversion Time Min Offset Error Input Noise TEMPERATURE SENSOR 2 Local Sensor Accuracy Local Sensor Supply Voltage Coefficient Remote Sensor Accuracy Remote Sensor Supply Voltage Coefficient Remote Sensor Current Source Temperature for Code 0x800 Temperature for Code 0xC00 Temperature Resolution per Code REFERENCE OUTPUT Reference Output Voltage Load Regulation Minimum Load Capacitance PSRR PROGRAMMABLE DRIVER OUTPUTS High Voltage (Charge Pump) Mode (PDO1 to PDO6) Output Impedance VOH IOUTAVG Standard (Digital Output) Mode (PDO1 to PDO10) VOH Typ 0.44 84 Max 0.25 Unit ms ms LSB LSB rms Test Conditions/Comments One conversion on one channel All 12 channels selected, 16x averaging enabled VREFIN = 2.048 V Direct input (no attenuator) 3 -1.7 3 -3 200 12 0 128 0.125 C C/V C C A A C C C VDDCAP = 4.75 V 2 2.043 2.048 -0.25 0.25 2.053 1 60 11 10.5 500 12.5 12 20 14 13.5 2.4 VOL IOL 3 ISINK3 RPULL-UP ISOURCE (VPx)3 Three-State Output Leakage Current Oscillator Frequency DIGITAL INPUTS (VXx, A0, A1) Input High Voltage, VIH Input Low Voltage, VIL Input High Current, IIH Input Low Current, IIL Input Capacitance Programmable Pull-Down Current, IPULL-DOWN SERIAL BUS DIGITAL INPUTS (SDA, SCL) Input High Voltage, VIH Input Low Voltage, VIL Output Low Voltage, VOL3 VPU - 0.3 0 19 20 90 100 No load Sourcing current, IDACxMAX = -100 A Sinking current, IDACxMAX = 100 A Capacitor required for decoupling, stability DC k V V A IOH = 0 A IOH = 1 A 2 V < VOH < 7 V 0.50 20 60 29 2 10 110 A kHz 2.0 0.8 -1 1 5 20 2.0 0.8 0.4 High level Low level VDDCAP = 4.75 V VDDCAP = 4.75 V V mV mV F dB V V V V mA mA k mA 4.5 VDDCAP = 4.75 V V V A A pF A V V V Rev. C | Page 5 of 32 VPU (pull-up to VDDCAP or VPx) = 2.7 V, IOH = 0.5 mA VPU to VPx = 6.0 V, IOH = 0 mA VPU 2.7 V, IOH = 0.5 mA IOL = 20 mA Maximum sink current per PDOx pin Maximum total sink for all PDOx pins Internal pull-up Current load on any VPx pull-ups, that is, total source current available through any number of PDOx pullup switches configured onto any one VPx pin VPDO = 14.4 V All on-chip time delays derived from this clock Maximum VIN = 5.5 V Maximum VIN = 5.5 V VIN = 5.5 V VIN = 0 V VDDCAP = 4.75 V, TA = 25C if known logic state is required IOUT = -3.0 mA ADM1063 Parameter SERIAL BUS TIMING 4 Clock Frequency, fSCLK Bus Free Time, tBUF Start Setup Time, tSU;STA Stop Setup Time, tSU;STO Start Hold Time, tHD;STA SCL Low Time, tLOW SCL High Time, tHIGH SCL, SDA Rise Time, tR SCL, SDA Fall Time, tF Data Setup Time, tSU;DAT Data Hold Time, tHD;DAT Input Low Current, IIL SEQUENCING ENGINE TIMING State Change Time Min Typ Max Unit Test Conditions/Comments 400 kHz s s s s s s ns ns ns ns A VIN = 0 V 1.3 0.6 0.6 0.6 1.3 0.6 300 300 100 5 1 10 s 1 At least one of the VH, VPx pins must be 3.0 V to maintain the device supply on VDDCAP. All temperature sensor measurements are taken with round-robin loop enabled and at least one other voltage input being measured. 3 Specification is not production tested but is supported by characterization data at initial product release. 4 Timing specifications are guaranteed by design and supported by characterization data. 2 Rev. C | Page 6 of 32 ADM1063 PDOGND NC 31 VCCP PDOGND 32 A0 VCCP 33 A1 A0 34 D2N A1 35 D2P D2N 36 D1N D2P 37 D1P D1N 38 VDDCAP D1P 39 GND VDDCAP 40 NC GND PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS 48 47 46 45 44 43 42 41 40 39 38 37 30 PDO1 NC 1 29 PDO2 VX1 2 VX3 3 28 PDO3 VX2 3 34 PDO2 VX4 4 27 PDO4 VX3 4 33 PDO3 26 PDO5 20 NOTES 1. THE LFCSP HAS AN EXPOSED PAD ON THE BOTTOM. THIS PAD IS A NO CONNECT (NC). IF POSSIBLE, THIS PAD SHOULD BE SOLDERED TO THE BOARD FOR IMPROVED MECHANICAL STABILITY. 2. NC = NO CONNECT. DO NOT CONNECT TO THIS PIN. 26 PDO10 NC 12 25 NC 13 14 15 16 17 18 19 20 21 22 23 24 04632-004 19 NC 18 27 PDO9 VH 11 NC 17 28 PDO8 VP4 10 NC 16 29 PDO7 VP3 9 SDA 15 30 PDO6 SCL 14 VP2 8 31 PDO5 NC 13 TOP VIEW (Not to Scale) NC 12 VP1 7 32 PDO4 REFOUT 11 ADM1063 REFIN PDO10 NC 21 NC VH 10 SDA PDO9 SCL PDO8 22 NC 23 VP4 9 NC VP3 8 REFOUT PDO7 REFIN PDO6 24 AGND 25 VP2 7 REFGND VP1 6 VX5 6 REFGND TOP VIEW (Not to Scale) VX4 5 35 PDO1 NC ADM1063 VX5 5 36 NC PIN 1 INDICATOR AGND PIN 1 INDICATOR VX2 2 NC = NO CONNECT 04632-003 VX1 1 Figure 3. LFCSP Pin Configuration Figure 4. TQFP Pin Configuration Table 2. Pin Function Descriptions LFCSP 1 15, 16, 19, 20 1 to 5 Pin No. TQFP 1, 12, 13, 18, 19, 22 to 25, 36, 37, 48 2 to 6 Mnemonic NC Description No Connection. VX1 to VX5 (VXx) VP1 to VP4 (VPx) High Impedance Inputs to Supply Fault Detectors. Fault thresholds can be set from 0.573 V to 1.375 V. Alternatively, these pins can be used as general-purpose digital inputs. Low Voltage Inputs to Supply Fault Detectors. Three input ranges can be set by altering the input attenuation on a potential divider connected to these pins, the output of which connects to a supply fault detector. These pins allow thresholds from 2.5 V to 6.0 V, from 1.25 V to 3.00 V, and from 0.573 V to 1.375 V. High Voltage Input to Supply Fault Detectors. Two input ranges can be set by altering the input attenuation on a potential divider connected to this pin, the output of which connects to a supply fault detector. This pin allows thresholds from 6.0 V to 14.4 V and from 2.5 V to 6.0 V. Ground Return for Input Attenuators. Ground Return for On-Chip Reference Circuits. Reference Input for ADC. Nominally, 2.048 V. This pin must be driven by a reference voltage. The on-board reference can be used by connecting the REFOUT pin to the REFIN pin. Reference Output, 2.048 V. Typically connected to REFIN. Note that the capacitor must be connected between this pin and REFGND. A 10 F capacitor is recommended for this purpose. SMBus Clock Pin. Bidirectional open drain requires external resistive pull-up. SMBus Data Pin. Bidirectional open drain requires external resistive pull-up. Programmable Output Drivers. Ground Return for Output Drivers. Central Charge Pump Voltage of 5.25 V. A reservoir capacitor must be connected between this pin and GND. A 10 F capacitor is recommended for this purpose. Logic Input. This pin sets the seventh bit of the SMBus interface address. Logic Input. This pin sets the sixth bit of the SMBus interface address. External Temperature Sensor 2 Cathode Connection. External Temperature Sensor 2 Anode Connection. 6 to 9 7 to 10 10 11 VH 11 12 13 14 15 16 AGND 2 REFGND2 REFIN 14 17 REFOUT 17 18 21 to 30 31 32 20 21 26 to 35 38 39 SCL SDA PDO10 to PDO1 PDOGND2 VCCP 33 34 35 36 40 41 42 43 A0 A1 D2N D2P Rev. C | Page 7 of 32 ADM1063 LFCSP 1 37 38 39 40 1 2 Pin No. TQFP 44 45 46 47 Mnemonic D1N D1P VDDCAP GND2 Description External Temperature Sensor 1 Cathode Connection. External Temperature Sensor 1 Anode Connection. Device Supply Voltage. Linearly regulated from the highest of the VPx, VH pins to a typical of 4.75 V. Note that the capacitor must be connected between this pin and GND. A 10 F capacitor is recommended for this purpose. Supply Ground. Note that the LFCSP has an exposed pad on the bottom. This pad is a no connect (NC). If possible, this pad should be soldered to the board for improved mechanical stability. In a typical application, all ground pins are connected together. Rev. C | Page 8 of 32 ADM1063 ABSOLUTE MAXIMUM RATINGS Table 3. Parameter Voltage on VH Pin Voltage on VPx Pins Voltage on VXx Pins Voltage on A0, A1 Pins Voltage on REFIN, REFOUT Pins Voltage on VDDCAP, VCCP Pins Voltage on PDOx Pins Voltage on SDA, SCL Pins Voltage on GND, AGND, PDOGND, REFGND Pins Voltage on DxN, DxP Pins Input Current at Any Pin Package Input Current Maximum Junction Temperature (TJ max) Storage Temperature Range Lead Temperature, Soldering Vapor Phase, 60 sec Rating 16 V 7V -0.3 V to +6.5 V -0.3 V to +7 V 5V 6.5 V 16 V 7V -0.3 V to +0.3 V -0.3 V to +5 V 5 mA 20 mA 150C -65C to +150C 215C ESD Rating, All Pins 2000 V Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. THERMAL RESISTANCE JA is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. Table 4. Thermal Resistance Package Type 40-Lead LFCSP 48-Lead TQFP ESD CAUTION Rev. C | Page 9 of 32 JA 25 50 Unit C/W C/W ADM1063 TYPICAL PERFORMANCE CHARACTERISTICS 180 6 160 5 140 120 IVP1 (A) VVDDCAP (V) 4 3 100 80 60 2 40 1 0 1 2 3 4 5 0 6 04632-053 04632-050 0 20 0 1 2 3 4 5 6 VVP1 (V) VVP1 (V) Figure 5. VVDDCAP vs. VVP1 Figure 8. IVP1 vs. VVP1 (VP1 Not as Supply) 6 5.0 4.5 5 4.0 3.5 3.0 IVH (mA) 3 2 2.0 1.5 1.0 04632-051 1 0 2.5 0 2 4 6 8 10 12 14 04632-054 VVDDCAP (V) 4 0.5 0 16 0 2 4 6 VVH (V) 8 10 12 14 16 VVH (V) Figure 6. VVDDCAP vs. VVH Figure 9. IVH vs. VVH (VH as Supply) 350 5.0 4.5 300 4.0 250 IVH (A) 3.0 2.5 2.0 1.5 200 150 100 1.0 0 1 2 3 4 5 0 6 04632-055 0.5 0 50 04632-052 IVP1 (mA) 3.5 0 1 2 3 4 VVH (V) VVP1 (V) Figure 10. IVH vs. VVH (VH Not as Supply) Figure 7. IVP1 vs. VVP1 (VP1 as Supply) Rev. C | Page 10 of 32 5 6 ADM1063 14 1.0 0.8 0.6 10 0.4 8 0.2 DNL (LSB) 6 0 -0.2 -0.4 4 -0.6 0 04632-056 2 0 2.5 5.0 7.5 10.0 12.5 04632-066 CHARGE-PUMPED VPDO1 (V) 12 -0.8 -1.0 15.0 0 1000 ILOAD (A) 4.5 0.8 4.0 0.6 3.5 0.4 VP1 = 5V 2.5 VP1 = 3V 0.2 0 -0.2 1.5 -0.4 1.0 -0.6 0.5 1 2 3 4 5 04632-063 INL (LSB) 3.0 04632-057 VPDO1 (V) 1.0 0 4000 Figure 14. DNL for ADC 5.0 0 3000 CODE Figure 11. Charge-Pumped VPDO1 (FET Drive Mode) vs. ILOAD 2.0 2000 -0.8 -1.0 6 0 1000 ILOAD (mA) 2000 3000 4000 CODE Figure 15. INL for ADC Figure 12. VPDO1 (Strong Pull-Up to VPx) vs. ILOAD 4.5 12000 4.0 9894 10000 3.5 2.5 VP1 = 3V 2.0 1.5 8000 6000 4000 1.0 0 0 10 20 30 40 50 25 0 60 2047 81 2048 2049 CODE ILOAD (A) Figure 16. ADC Noise, Midcode Input, 10,000 Reads Figure 13. VPDO1 (Weak Pull-Up to VPx) vs. ILOAD Rev. C | Page 11 of 32 04632-064 2000 0.5 04632-058 VPDO1 (V) HITS PER CODE VP1 = 5V 3.0 ADM1063 2.058 VP1 = 3.0V 2.048 VP1 = 4.75V 2.043 2.038 -40 04632-061 REFOUT (V) 2.053 -20 0 20 40 60 80 100 TEMPERATURE (C) Figure 17. REFOUT vs. Temperature Rev. C | Page 12 of 32 ADM1063 POWERING THE ADM1063 An external capacitor to GND is required to decouple the on-chip supply from noise. This capacitor should be connected to the VDDCAP pin, as shown in Figure 18. The capacitor has another use during brownouts (momentary loss of power). Under these conditions, when the input supply (VPx or VH) dips transiently below VDD, the synchronous rectifier switch immediately turns off so that it does not pull VDD down. The VDD capacitor can then act as a reservoir to keep the device active until the next highest supply takes over the powering of the device. A 10 F capacitor is recommended for this reservoir/decoupling function. When two or more supplies are within 100 mV of each other, the supply that first takes control of VDD keeps control. For example, if VP1 is connected to a 3.3 V supply, VDD powers up to approximately 3.1 V through VP1. If VP2 is then connected to another 3.3 V supply, VP1 still powers the device, unless VP2 goes 100 mV higher than VP1. VDDCAP VP1 IN OUT 4.75V LDO EN VP2 IN OUT 4.75V LDO EN VP3 IN OUT 4.75V LDO EN VP4 IN OUT 4.75V LDO EN VH The VH input pin can accommodate supplies up to 14.4 V, which allows the ADM1063 to be powered using a 12 V backplane supply. In cases where this 12 V supply is hot swapped, it is recommended that the ADM1063 not be connected directly to the supply. Suitable precautions, such as the use of a hot swap controller, should be taken to protect the device from transients that could cause damage during hot swap events. Rev. C | Page 13 of 32 IN OUT 4.75V LDO INTERNAL DEVICE SUPPLY EN SUPPLY COMPARATOR 04632-022 The ADM1063 is powered from the highest voltage input on either the positive-only supply inputs (VPx) or the high voltage supply input (VH). This technique offers improved redundancy because the device is not dependent on any particular voltage rail to keep it operational. The same pins are used for supply fault detection (see the Supply Supervision section). A VDD arbitrator on the device chooses which supply to use. The arbitrator can be considered an OR'ing of five low dropout regulators (LDOs) together. A supply comparator chooses the highest input to provide the on-chip supply. There is minimal switching loss with this architecture (~0.2 V), resulting in the ability to power the ADM1063 from a supply as low as 3.0 V. Note that the supply on the VXx pins cannot be used to power the device. Figure 18. VDD Arbitrator Operation ADM1063 INPUTS SUPPLY SUPERVISION The threshold value required is given by The ADM1063 has 10 programmable inputs. Five of these are dedicated supply fault detectors (SFDs). These dedicated inputs are called VH and VPx (VP1 to VP4) by default. The other five inputs are labeled VXx (VX1 to VX5) and have dual functionality. They can be used either as SFDs, with functionality similar to VH and VPx, or as CMOS-/TTL-compatible logic inputs to the device. Therefore, the ADM1063 can have up to 10 analog inputs, a minimum of five analog inputs and five digital inputs, or a combination thereof. If an input is used as an analog input, it cannot be used as a digital input. Therefore, a configuration requiring 10 analog inputs has no available digital inputs. Table 6 shows the details of each input. VT = (VR x N)/255 + VB where: VT is the desired threshold voltage (undervoltage or overvoltage). VR is the voltage range. N is the decimal value of the 8-bit code. VB is the bottom of the range. Reversing the equation, the code for a desired threshold is given by N = 255 x (VT - VB)/VR For example, if the user wants to set a 5 V overvoltage threshold on VP1, the code to be programmed in the PS1OVTH register (as discussed in the AN-698 Application Note at www.analog.com) is given by PROGRAMMING THE SUPPLY FAULT DETECTORS The ADM1063 can have up to 10 SFDs on its 10 input channels. These highly programmable reset generators enable the supervision of up to 10 supply voltages. The supplies can be as low as 0.573 V and as high as 14.4 V. The inputs can be configured to detect an undervoltage fault (the input voltage drops below a preprogrammed value), an overvoltage fault (the input voltage rises above a preprogrammed value), or an out-of-window fault (the input voltage is outside a preprogrammed range). The thresholds can be programmed to an 8-bit resolution in registers provided in the ADM1063. This translates to a voltage resolution that is dependent on the range selected. The resolution is given by N = 255 x (5 - 2.5)/3.5 Therefore, N = 182 (1011 0110 or 0xB6). INPUT COMPARATOR HYSTERESIS The UV and OV comparators shown in Figure 19 are always monitoring VPx. To avoid chatter (multiple transitions when the input is very close to the set threshold level), these compara tors have digitally programmable hysteresis. The hysteresis can be programmed up to the values shown in Table 6. RANGE SELECT ULTRA LOW Step Size = Threshold Range/255 VREF Therefore, if the high range is selected on VH, the step size can be calculated as follows: Table 5 lists the upper and lower limits of each available range, the bottom of each range (VB), and the range itself (VR). VB (V) 0.573 1.25 2.5 6.0 VR (V) 0.802 1.75 3.5 8.4 - GLITCH FILTER FAULT OUTPUT - UV FAULT TYPE COMPARATOR SELECT 04632-023 MID Table 5. Voltage Range Limits OV COMPARATOR + LOW (14.4 V - 6.0 V)/255 = 32.9 mV Voltage Range (V) 0.573 to 1.375 1.25 to 3.00 2.5 to 6.0 6.0 to 14.4 + VPx Figure 19. Supply Fault Detector Block The hysteresis is added after a supply voltage goes out of tolerance. Therefore, the user can program the amount above the undervoltage threshold to which the input must rise before an undervoltage fault is deasserted. Similarly, the user can program the amount below the overvoltage threshold to which an input must fall before an overvoltage fault is deasserted. Table 6. Input Functions, Thresholds, and Ranges Input VH Function High Voltage Analog Input VPx Positive Analog Input VXx High-Z Analog Input Digital Input Voltage Range (V) 2.5 to 6.0 6.0 to 14.4 0.573 to 1.375 1.25 to 3.00 2.5 to 6.0 0.573 to 1.375 0 to 5.0 Maximum Hysteresis 425 mV 1.02 V 97.5 mV 212 mV 425 mV 97.5 mV N/A Rev. C | Page 14 of 32 Voltage Resolution (mV) 13.7 32.9 3.14 6.8 13.7 3.14 N/A Glitch Filter (s) 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 0 to 100 ADM1063 The hysteresis value is given by VHYST = VR x NTHRESH/255 where: VHYST is the desired hysteresis voltage. NTHRESH is the decimal value of the 5-bit hysteresis code. Note that NTHRESH has a maximum value of 31. The maximum hysteresis for the ranges is listed in Table 6. INPUT GLITCH FILTERING The final stage of the SFDs is a glitch filter. This block provides time-domain filtering on the output of the SFD comparators, which allows the user to remove any spurious transitions, such as supply bounce at turn-on. The glitch filter function is in addition to the digitally programmable hysteresis of the SFD comparators. The glitch filter timeout is programmable up to 100 s. For example, when the glitch filter timeout is 100 s, any pulse appearing on the input of the glitch filter block that is less than 100 s in duration is prevented from appearing on the output of the glitch filter block. Any input pulse that is longer than 100 s appears on the output of the glitch filter block. The output is delayed with respect to the input by 100 s. The filtering process is shown in Figure 20. INPUT PULSE SHORTER THAN GLITCH FILTER TIMEOUT INPUT PULSE LONGER THAN GLITCH FILTER TIMEOUT PROGRAMMED TIMEOUT PROGRAMMED TIMEOUT tGF t0 OUTPUT t0 tGF OUTPUT t0 VXx PINS AS DIGITAL INPUTS As discussed in the Supply Supervision with VXX Inputs section, the VXx input pins on the ADM1063 have dual functionality. The second function is as a digital logic input to the device. Therefore, the ADM1063 can be configured for up to five digital inputs. These inputs are TTL-/CMOS-compatible. Standard logic signals can be applied to the pins: RESET from reset generators, PWRGD signals, fault flags, manual resets, and so on. These signals are available as inputs to the SE and, therefore, can be used to control the status of the PDOs. The inputs can be configured to detect either a change in level or an edge. When configured for level detection, the output of the digital block is a buffered version of the input. When configured for edge detection, a pulse of programmable width is output from the digital block once the logic transition is detected. The width is programmable from 0 s to 100 s. tGF tGF 04632-024 t0 INPUT The secondary SFDs are fixed to the same input range as the primary SFDs. They are used to indicate warning levels rather than failure levels. This allows faults and warnings to be generated on a single supply using only one pin. For example, if VP1 is set to output a fault when a 3.3 V supply drops to 3.0 V, VX1 can be set to output a warning at 3.1 V. Warning outputs are available for readback from the status registers. They are also OR'ed together and fed into the SE, allowing warnings to generate interrupts on the PDOs. Therefore, in this example, if the supply drops to 3.1 V, a warning is generated and remedial action can be taken before the supply drops out of tolerance. Figure 20. Input Glitch Filter Function SUPPLY SUPERVISION WITH VXx INPUTS The VXx inputs have two functions. They can be used as either supply fault detectors or digital logic inputs. When selected as analog (SFD) inputs, the VXx pins have functionality that is very similar to the VH and VPx pins. The primary difference is that the VXx pins have only one input range: 0.573 V to 1.375 V. Therefore, these inputs can directly supervise only the very low supplies. However, the input impedance of the VXx pins is high, allowing an external resistor divide network to be connected to the pin. Thus, potentially any supply can be divided down into the input range of the VXx pin and supervised, enabling the ADM1063 to monitor other supplies, such as +24 V, +48 V, and -5 V. The digital blocks feature the same glitch filter function that is available on the SFDs. This enables the user to ignore spurious transitions on the inputs. For example, the filter can be used to debounce a manual reset switch. When configured as digital inputs, each VXx pin has a weak (10 A) pull-down current source available for placing the input into a known condition, even if left floating. The current source, if selected, weakly pulls the input to GND. VXx (DIGITAL INPUT) Rev. C | Page 15 of 32 + DETECTOR GLITCH FILTER TO SEQUENCING ENGINE - VREF = 1.4V Figure 21. VXx Digital Input Function 04632-027 INPUT An additional supply supervision function is available when the VXx pins are selected as digital inputs. In this case, the analog function is available as a second detector on each of the dedicated analog inputs, VPx and VH. The analog function of VX1 is mapped to VP1, VX2 is mapped to VP2, and so on; VX5 is mapped to VH. In this case, these SFDs can be viewed as secondary or warning SFDs. ADM1063 OUTPUTS SUPPLY SEQUENCING THROUGH CONFIGURABLE OUTPUT DRIVERS register (see the AN-698 Application Note at www.analog.com for details). Supply sequencing is achieved with the ADM1063 using the programmable driver outputs (PDOs) on the device as control signals for supplies. The output drivers can be used as logic enables or as FET drivers. The data sources are as follows: * * The sequence in which the PDOs are asserted (and, therefore, the supplies are turned on) is controlled by the sequencing engine (SE). The SE determines what action is taken with the PDOs, based on the condition of the ADM1063 inputs. Therefore, the PDOs can be set up to assert when the SFDs are in tolerance, the correct input signals are received on the VXx digital pins, no warnings are received from any of the inputs of the device, and at other times. The PDOs can be used for a variety of functions. The primary function is to provide enable signals for LDOs or dc-to-dc converters that generate supplies locally on a board. The PDOs can also be used to provide a PWRGD signal, when all the SFDs are in tolerance, or a RESET output if one of the SFDs goes out of specification (this can be used as a status signal for a DSP, FPGA, or other microcontroller). * DEFAULT OUTPUT CONFIGURATION All of the internal registers in an unprogrammed ADM1063 device from the factory are set to 0. Because of this, the PDOx pins are pulled to GND by a weak (20 k) on-chip pull-down resistor. As the input supply to the ADM1063 ramps up on VPx or VH, all PDOx pins behave as follows: * * The PDOs can be programmed to pull up to a number of different options. The outputs can be programmed as follows: The internal pull-down can be overdriven with an external pullup of suitable value tied from the PDOx pin to the required pull-up voltage. The 20 k resistor must be accounted for in calculating a suitable value. For example, if PDOx must be pulled up to 3.3 V, and 5 V is available as an external supply, the pull-up resistor value is given by The last option (available only on PDO1 to PDO6) allows the user to directly drive a voltage high enough to fully enhance an external N-FET, which is used to isolate, for example, a cardside voltage from a backplane supply (a PDO can sustain greater than 10.5 V into a 1 A load). The pull-down switches can also be used to drive status LEDs directly. 3.3 V = 5 V x 20 k/(RUP + 20 k) Therefore, RUP = (100 k - 66 k)/3.3 V = 10 k The data driving each of the PDOs can come from one of three sources. The source can be enabled in the PDOxCFG configuration VFET (PDO1 TO PDO6 ONLY) VDD VP4 10 10 20k VP1 SEL 20k CFG4 CFG5 CFG6 10 SE DATA PDO SMBus DATA 20k CLK DATA Figure 22. Programmable Driver Output Rev. C | Page 16 of 32 04632-028 * * * * * * * Open drain (allowing the user to connect an external pull-up resistor). Open drain with weak pull-up to VDD. Open drain with strong pull-up to VDD. Open drain with weak pull-up to VPx. Open drain with strong pull-up to VPx. Strong pull-down to GND. Internally charge-pumped high drive (12 V, PDO1 to PDO6 only). Input supply = 0 V to 1.2 V. The PDOs are high impedance. Input supply = 1.2 V to 2.7 V. The PDOs are pulled to GND by a weak (20 k) on-chip pull-down resistor. Supply > 2.7 V. Factory programmed devices continue to pull all PDOs to GND by a weak (20 k) on-chip pull-down resistor. Programmed devices download current EEPROM configuration data, and the programmed setup is latched. The PDO then goes to the state demanded by the configuration. This provides a known condition for the PDOs during power-up. 20k * Output from the SE. Directly from the SMBus. A PDO can be configured so that the SMBus has direct control over it. This enables software control of the PDOs. Therefore, a microcontroller can be used to initiate a software power-up/power-down sequence. On-chip clock. A 100 kHz clock is generated on the device. This clock can be made available on any of the PDOs. It can be used, for example, to clock an external device such as an LED. ADM1063 SEQUENCING ENGINE OVERVIEW The SE state machine comprises 63 state cells. Each state has the following attributes: * * * * * * Monitors signals indicating the status of the 10 input pins, VP1 to VP4, VH, and VX1 to VX5. Can be entered from any other state. Three exit routes move the state machine onto a next state: sequence detection, fault monitoring, and timeout. Delay timers for the sequence and timeout blocks can be programmed independently and changed with each state change. The range of timeouts is from 0 ms to 400 ms. Output condition of the 10 PDO pins is defined and fixed within a state. Transition from one state to the next is made in less than 20 s, which is the time needed to download a state definition from EEPROM to the SE. MONITOR FAULT STATE TIMEOUT SEQUENCE 04632-029 The ADM1063 sequencing engine (SE) provides the user with powerful and flexible control of sequencing. The SE implements a state machine control of the PDO outputs, with state changes conditional on input events. SE programs can enable complex control of boards such as power-up and power-down sequence control, fault event handling, interrupt generation on warnings, and so on. A watchdog function that verifies the continued operation of a processor clock can be integrated into the SE program. The SE can also be controlled via the SMBus, giving software or firmware control of the board sequencing. Figure 23. State Cell The ADM1063 offers up to 63 state definitions. The signals monitored to indicate the status of the input pins are the outputs of the SFDs. WARNINGS The SE also monitors warnings. These warnings can be generated when the ADC readings violate their limit register value or when the secondary voltage monitors on VPx and VH are triggered. The warnings are OR'ed together and are available as a single warning input to each of the three blocks that enable exiting a state. SMBus JUMP (UNCONDITIONAL JUMP) The SE can be forced to advance to the next state unconditionally. This enables the user to force the SE to advance. Examples of the use of this feature include moving to a margining state or debugging a sequence. The SMBus jump or go-to command can be seen as another input to sequence and timeout blocks to provide an exit from each state. Table 7. Sample Sequence State Entries State IDLE1 IDLE2 EN3V3 Sequence If VX1 is low , go to State IDLE2. If VP1 is okay, go to State EN3V3. If VP2 is okay, go to State EN2V5. DIS3V3 EN2V5 If VX1 is high, go to State IDLE1. If VP3 is okay, go to State PWRGD. DIS2V5 FSEL1 FSEL2 PWRGD If VX1 is high, go to State IDLE1. If VP3 is not okay, go to State DIS2V5. If VP2 is not okay, go to State DIS3V3. If VX1 is high, go to State DIS2V5. Timeout Monitor If VP2 is not okay after 10 ms, go to State DIS3V3. If VP1 is not okay, go to State IDLE1. If VP3 is not okay after 20 ms, go to State DIS2V5. If VP1 or VP2 is not okay, go to State FSEL2. If VP1 or VP2 is not okay, go to State FSEL2. If VP1 is not okay, go to State IDLE1. If VP1, VP2, or VP3 is not okay, go to State FSEL1. Rev. C | Page 17 of 32 ADM1063 SEQUENCING ENGINE APPLICATION EXAMPLE The application in this section demonstrates the operation of the SE. Figure 25 shows how the simple building block of a single SE state can be used to build a power-up sequence for a threesupply system. Table 8 lists the PDO outputs for each state in the same SE implementation. In this system, a good 5 V supply on VP1 and the VX1 pin held low are the triggers required to start a power-up sequence. The sequence next turns on the 3.3 V supply, then the 2.5 V supply (assuming successful turn-on of the 3.3 V supply). When all three supplies have turned on correctly, the PWRGD state is entered, where the SE remains until a fault occurs on one of the three supplies, or until it is instructed to go through a power-down sequence by VX1 going high. If a timer delay is specified, the input to the sequence detector must remain in the defined state for the duration of the timer delay. If the input changes state during the delay, the timer is reset. The sequence detector can also help to identify monitoring faults. In the sample application shown in Figure 25, the FSEL1 and FSEL2 states first identify which of the VP1,VP2, or VP3 pins has faulted, and then they take appropriate action. SEQUENCE STATES IDLE1 VX1 = 0 Faults are dealt with throughout the power-up sequence on a case-by-case basis. The following three sections (the Sequence Detector section, the Monitoring Fault Detector section, and the Timeout Detector section) describe the individual blocks and use the sample application shown in Figure 25 to demonstrate the actions of the state machine. IDLE2 The sequence detector block is used to detect when a step in a sequence has been completed. It looks for one of the SE inputs to change state and is most often used as the gate for successful progress through a power-up or power-down sequence. A timer block that is included in this detector can insert delays into a power-up or power-down sequence, if required. Timer delays can be set from 10 s to 400 ms. Figure 24 is a block diagram of the sequence detector. VX5 SUPPLY FAULT DETECTION TIMEOUT STATES EN3V3 10ms VP1 = 0 Sequence Detector VP1 VP1 = 1 MONITOR FAULT STATES VP2 = 1 EN2V5 DIS3V3 20ms (VP1 + VP2) = 0 VX1 = 1 VP3 = 1 PWRGD DIS2V5 VP2 = 0 (VP1 + VP2 + VP3) = 0 VX1 = 1 (VP1 + VP2) = 0 SEQUENCE DETECTOR FSEL1 VX1 = 1 VP3 = 0 FSEL2 LOGIC INPUT CHANGE OR FAULT DETECTION VP1 = 0 TIMER VP2 = 0 04632-030 WARNINGS INVERT FORCE FLOW (UNCONDITIONAL JUMP) 04632-032 Figure 25. Sample Application Flow Diagram SELECT Figure 24. Sequence Detector Block Diagram Table 8. PDO Outputs for Each State PDO Outputs PDO1 = 3V3ON PDO2 = 2V5ON PDO3 = FAULT IDLE1 0 0 0 IDLE2 0 0 0 EN3V3 1 0 0 EN2V5 1 1 0 DIS3V3 0 1 1 Rev. C | Page 18 of 32 DIS2V5 1 0 1 PWRGD 1 1 0 FSEL1 1 1 1 FSEL2 1 1 1 ADM1063 Monitoring Fault Detector Timeout Detector The monitoring fault detector block is used to detect a failure on an input. The logical function implementing this is a wide OR gate that can detect when an input deviates from its expected condition. The clearest demonstration of the use of this block is in the PWRGD state, where the monitor block indicates that a failure on one or more of the VP1, VP2, or VP3 inputs has occurred. The timeout detector allows the user to trap a failure to ensure proper progress through a power-up or power-down sequence. No programmable delay is available in this block because the triggering of a fault condition is likely to be caused by a supply falling out of tolerance. In this situation, the device needs to react as quickly as possible. Some latency occurs when moving out of this state because it takes a finite amount of time (~20 s) for the state configuration to download from EEPROM into the SE. Figure 26 is a block diagram of the monitoring fault detector. MONITORING FAULT DETECTOR 1-BIT FAULT DETECTOR VP1 The ADM1063 has a fault latch for recording faults. Two registers, FSTAT1 and FSTAT2, are set aside for this purpose. A single bit is assigned to each input of the device, and a fault on that input sets the relevant bit. The contents of the fault register can be read out over the SMBus to determine which input(s) faulted. The fault register can be enabled/disabled in each state. To latch data from one state, ensure that the fault latch is disabled in the following state. This ensures that only real faults are captured and not, for example, undervoltage conditions that may be present during a power-up or power-down sequence. MASK SENSE 1-BIT FAULT DETECTOR FAULT LOGIC INPUT CHANGE OR FAULT DETECTION MASK SENSE 1-BIT FAULT DETECTOR FAULT WARNINGS MASK Figure 26. Monitoring Fault Detector Block Diagram 04632-033 VX5 The power-up sequence progresses when this change is detected. If, however, the supply fails (perhaps due to a short circuit overloading this supply), the timeout block traps the problem. In this example, if the 3.3 V supply fails within 10 ms, the SE moves to the DIS3V3 state and turns off this supply by bringing PDO1 low. It also indicates that a fault has occurred by taking PDO3 high. Timeout delays of 100 s to 400 ms can be programmed. FAULT AND STATUS REPORTING FAULT SUPPLY FAULT DETECTION In the sample application shown in Figure 25, the timeout nextstate transition is from the EN3V3 and EN2V5 states. For the EN3V3 state, the signal 3V3ON is asserted on the PDO1 output pin upon entry to this state to turn on a 3.3 V supply. This supply rail is connected to the VP2 pin, and the sequence detector looks for the VP2 pin to go above its undervoltage threshold, which is set in the supply fault detector (SFD) attached to that pin. The ADM1063 also has a number of status registers. These include more detailed information, such as whether an undervoltage or overvoltage fault is present on a particular input. The status registers also include information on ADC limit faults. Note that the data in the status registers is not latched in any way and, therefore, is subject to change at any time. See the AN-698 Application Note at www.analog.com for full details about the ADM1063 registers. Rev. C | Page 19 of 32 ADM1063 VOLTAGE READBACK The ADM1063 has an on-board, 12-bit, accurate ADC for voltage readback over the SMBus. The ADC has a 13-channel analog mux on the front end. The 13 channels consist of the 10 SFD inputs (VH, VPx, and VXx), plus three channels for temperature readback (see the Temperature Measurement System section). Any or all of these inputs can be selected to be read, in turn, by the ADC. The circuit controlling this operation is called the round-robin circuit. This circuit can be selected to run through its loop of conversions once or continuously. Averaging is also provided for each channel. In this case, the round-robin circuit runs through its loop of conversions 16 times before returning a result for each channel. At the end of this cycle, the results are written to the output registers. The ADC samples single-sided inputs with respect to the AGND pin. A 0 V input gives out Code 0, and an input equal to the voltage on REFIN gives out full code (4095 decimal). The inputs to the ADC come directly from the VXx pins and from the back of the input attenuators on the VPx and VH pins, as shown in Figure 27 and Figure 28. DIGITIZED VOLTAGE READING NO ATTENUATION 04632-025 12-BIT ADC VXx 2.048V VREF DIGITIZED VOLTAGE READING 04632-026 12-BIT ADC Figure 28. ADC Reading on VPx/VH Pins The voltage at the input pin can be derived from the following equation: V= ADC Code 4095 1 Attenuation Factor 1 2.181 4.363 10.472 ADC Input Voltage Range (V) 0 to 2.048 0 to 4.46 0 to 6.01 0 to 14.41 The upper limit is the absolute maximum allowed voltage on the VPx and VH pins. The typical way to supply the reference to the ADC on the REFIN pin is to connect the REFOUT pin to the REFIN pin. REFOUT provides a 2.048 V reference. As such, the supervising range covers less than half the normal ADC range. It is possible, however, to provide the ADC with a more accurate external reference for improved readback accuracy. Supplies can also be connected to the input pins purely for ADC readback, even though these pins may go above the expected supervisory range limits (but not above the absolute maximum ratings on these pins). For example, a 1.5 V supply connected to the VX1 pin can be correctly read out as an ADC code of approximately 3/4 full scale, but it always sits above any supervisory limits that can be set on that pin. The maximum setting for the REFIN pin is 2.048 V. In addition to the readback capability, another level of supervision is provided by the on-chip, 12-bit ADC. The ADM1063 has limit registers with which the user can program a maximum or minimum allowable threshold. Exceeding the threshold generates a warning that can either be read back from the status registers or input into the SE to determine what sequencing action the ADM1063 should take. Only one register is provided for each input channel. Therefore, either an undervoltage threshold or overvoltage threshold (but not both) can be set for a given channel. The roundrobin circuit can be enabled via an SMBus write, or it can be programmed to turn on in any state in the SE program. For example, it can be set to start after a power-up sequence is complete, and all supplies are known to be within expected tolerance limits. ATTENUATION NETWORK (DEPENDS ON RANGE SELECTED) 2.048V VREF SFD Input Range (V) 0.573 to 1.375 1.25 to 3.00 2.5 to 6.0 6.0 to 14.4 SUPPLY SUPERVISION WITH THE ADC Figure 27. ADC Reading on VXx Pins VPx/VH Table 9. ADC Input Voltage Ranges x Attenuation Factor x VREFIN where VREFIN = 2.048 V when the internal reference is used (that is, the REFIN pin is connected to the REFOUT pin). The ADC input voltage ranges for the SFD input ranges are listed in Table 9. Note that a latency is built into this supervision, dictated by the conversion time of the ADC. With all 12 channels selected, the total time for the round-robin operation (averaging off) is approximately 6 ms (500 s per channel selected). Supervision using the ADC, therefore, does not provide the same real-time response as the SFDs. Rev. C | Page 20 of 32 ADM1063 TEMPERATURE MEASUREMENT SYSTEM Figure 31 shows the input signal conditioning used to measure the output of a remote temperature sensor. This figure shows the external sensor as a substrate transistor provided for temperature monitoring on some microprocessors, but it could equally be a discrete transistor such as a 2N3904 or 2N3906. The ADM1063 contains an on-chip, band gap temperature sensor, whose output is digitized by the on-chip, 12-bit ADC. Theoretically, the temperature sensor and the ADC can measure temperatures from -128C to +128C with a resolution of 0.125C. Because this exceeds the operating temperature range of the device, local temperature measurements outside this range are not possible. Temperature measurements from -128C to +128C are possible using a remote sensor. The output code is in offset binary format, with -128C given by Code 0x400, 0C given by Code 0x800, and +128C given by Code 0xC00. If a discrete transistor is used, the collector is not grounded and should be linked to the base. If a PNP transistor is used, the base is connected to the DxN input and the emitter is connected to the DxP input. If an NPN transistor is used, the emitter is connected to the DxN input and the base is connected to the DxP input. Figure 29 and Figure 30 show how to connect the ADM1063 to an NPN or PNP transistor for temperature measurement. To prevent ground noise from interfering with the measurement, the more negative terminal of the sensor is not referenced to ground but is biased above ground by an internal diode at the DxN input. As with the other analog inputs to the ADC, a limit register is provided for each of the temperature input channels. Therefore, a temperature limit can be set such that if it is exceeded, a warning is generated and available as an input to the sequencing engine. This enables users to control their sequence or monitor functions based on an overtemperature or undertemperature event. REMOTE TEMPERATURE MEASUREMENT ADM1063 2N3904 NPN DxP 04632-070 The ADM1063 can measure the temperature of two remote diode sensors or diode-connected transistors connected to the DxN and DxP pins. DxN The forward voltage of a diode or diode-connected transistor operated at a constant current exhibits a negative temperature coefficient of about -2 mV/C. Unfortunately, the absolute value of VBE varies from device to device, and individual calibration is required to null it, making the technique unsuitable for mass production. The technique used in the ADM1063 is to measure the change in VBE when the device is operated at two different currents. Figure 29. Measuring Temperature Using an NPN Transistor ADM1063 DxP DxN 04632-071 2N3906 PNP The change in VBE is given by Figure 30. Measuring Temperature Using a PNP Transistor VBE = kT/q x ln(N) where: k is Boltzmann's constant. q is the charge on the carrier. T is the absolute temperature in Kelvin. N is the ratio of the two currents. VDD REMOTE SENSING TRANSISTOR I THERM DA DxP THERM DC DxN NxI IBIAS VOUT+ TO ADC BIAS DIODE LOW-PASS FILTER fC = 65kHz Figure 31. Signal Conditioning for Remote Diode Temperature Sensors Rev. C | Page 21 of 32 VOUT- 04632-069 CPU ADM1063 To measure VBE, the sensor is switched between operating currents of I and N x I. The resulting waveform is passed through a 65 kHz low-pass filter to remove noise and through a chopperstabilized amplifier that amplifies and rectifies the waveform to produce a dc voltage proportional to VBE. This voltage is measured by the ADC to produce a temperature output in 12-bit offset binary. To further reduce the effects of noise, digital filtering is performed by averaging the results of 16 measurement cycles. A remote temperature measurement takes nominally 600 ms. The results of remote temperature measurements are stored in 12-bit, offset binary format, as shown in Table 10. This format provides temperature readings with a resolution of 0.125C. Table 10. Temperature Data Format Temperature -128C -125C -100C -75C -50C -25C -10C 0C +10.25C +25.5C +50.75C +75C +100C +125C +128C Rev. C | Page 22 of 32 Digital Output (Hex) 0x400 0x418 0x4E0 0x5A8 0x670 0x738 0x7B0 0x800 0x852 0x8CC 0x996 0xA58 0XB20 0xBE8 0xC00 Digital Output (Binary) 010000000000 010000011000 010011100000 010110101000 011001110000 011100111000 011110110000 100000000000 100001010010 100011001100 100110010110 101001011000 101100100000 101111101000 110000000000 ADM1063 APPLICATIONS DIAGRAM 12V IN 12V OUT 5V IN 5V OUT 3V IN 3V OUT IN DC-TO-DC1 EN VH 5V OUT 3V OUT 3.3V OUT 2.5V OUT 1.8V OUT 1.2V OUT 0.9V OUT POWRON OUT 3.3V OUT ADM1063 VP1 VP2 VP3 VP4 VX1 VX2 VX3 PDO1 PDO2 VX4 PDO6 IN DC-TO-DC2 PDO3 PDO4 PDO5 RESET PDO7 VX5 PDO8 EN OUT 2.5V OUT PWRGD SIGNAL VALID IN SYSTEM RESET DC-TO-DC3 EN PDO9 PDO10 OUT 1.8V OUT 3.3V OUT REFOUT D1P IN D1N D2P LDO D2N REFIN VCCP VDDCAP GND EN OUT 0.9V OUT 3.3V OUT IN 10F 10F 10F EN TEMPERATURE DIODE 3.3V OUT 2.5V OUT OUT 1.2V OUT DC-TO-DC4 MICROPROCESSOR TEMPERATURE DIODE 2.5V OUT MICROPROCESSOR 04632-068 3.3V OUT Figure 32. Applications Diagram Rev. C | Page 23 of 32 ADM1063 COMMUNICATING WITH THE ADM1063 CONFIGURATION DOWNLOAD AT POWER-UP The configuration of the ADM1063 (undervoltage/overvoltage thresholds, glitch filter timeouts, PDO configurations, and so on) is dictated by the contents of the RAM. The RAM comprises digital latches that are local to each of the functions on the device. The latches are double-buffered and have two identical latches, Latch A and Latch B. Therefore, when an update to a function occurs, the contents of Latch A are updated first, and then the contents of Latch B are updated with identical data. The advantages of this architecture are explained in detail in the Updating the Configuration section. The latches are volatile memory and lose their contents at power-down. Therefore, the configuration in the RAM must be restored at power-up by downloading the contents of the EEPROM (nonvolatile memory) to the local latches. This download occurs in steps, as follows: 1. 2. 3. 4. 5. 6. With no power applied to the device, the PDOs are all high impedance. When 1.2 V appears on any of the inputs connected to the VDD arbitrator (VH or VPx), the PDOs are all weakly pulled to GND with a 20 k resistor. When the supply rises above the undervoltage lockout of the device (UVLO is 2.5 V), the EEPROM starts to download to the RAM. The EEPROM downloads its contents to all Latch As. When the contents of the EEPROM are completely downloaded to the Latch As, the device controller signals all Latch As to download to all Latch Bs simultaneously, completing the configuration download. At 0.5 ms after the configuration download completes, the first state definition is downloaded from EEPROM into the SE. Note that any attempt to communicate with the device prior to the completion of the download causes the ADM1063 to issue a no acknowledge (NACK). UPDATING THE CONFIGURATION After power-up, with all the configuration settings loaded from the EEPROM into the RAM registers, the user may need to alter the configuration of functions on the ADM1063, such as changing the undervoltage or overvoltage limit of an SFD, changing the fault output of an SFD, or adjusting the rise time delay of one of the PDOs. The ADM1063 provides several options that allow the user to update the configuration over the SMBus interface. The following three options are controlled in the UPDCFG register. Option 1 Update the configuration in real time. The user writes to the RAM across the SMBus, and the configuration is updated immediately. Option 2 Update the Latch As without updating the Latch Bs. With this method, the configuration of the ADM1063 remains unchanged and continues to operate in the original setup until the instruction is given to update the Latch Bs. Option 3 Change the EEPROM register contents without changing the RAM contents, and then download the revised EEPROM contents to the RAM registers. With this method, the configuration of the ADM1063 remains unchanged and continues to operate in the original setup until the instruction is given to update the RAM. The instruction to download from the EEPROM in Option 3 is also a useful way to restore the original EEPROM contents, if revisions to the configuration are unsatisfactory. For example, if the user needs to alter an overvoltage threshold, the RAM register can be updated as described in Option 1. However, if the user is not satisfied with the change and wants to revert to the original programmed value, the device controller can issue a command to download the EEPROM contents to the RAM again, as described in Option 3, restoring the ADM1063 to its original configuration. The topology of the ADM1063 makes this type of operation possible. The local, volatile registers (RAM) are all doublebuffered latches. Setting Bit 0 of the UPDCFG register to 1 leaves the double-buffered latches open at all times. If Bit 0 is set to 0 when a RAM write occurs across the SMBus, only the first side of the double-buffered latch is written to. The user must then write a 1 to Bit 1 of the UPDCFG register. This generates a pulse to update all the second latches at once. EEPROM writes occur in a similar way. The final bit in this register can enable or disable EEPROM page erasure. If this bit is set high, the contents of an EEPROM page can all be set to 1. If this bit is set low, the contents of a page cannot be erased, even if the command code for page erasure is programmed across the SMBus. The bit map for the UPDCFG register is shown in the AN-698 Application Note at www.analog.com. A flow diagram for download at power-up and subsequent configuration updates is shown in Figure 33. Rev. C | Page 24 of 32 ADM1063 SMBus E E P R O M L D DEVICE CONTROLLER R A M L D D A T A U P D LATCH A LATCH B EEPROM FUNCTION (OV THRESHOLD ON VP1) 04632-035 POWER-UP (VCC > 2.5V) Figure 33. Configuration Update Flow Diagram UPDATING THE SEQUENCING ENGINE Sequencing engine (SE) functions are not updated in the same way as regular configuration latches. The SE has its own dedicated 512-byte nonvolatile, electrically erasable, programmable, readonly memory (EEPROM) for storing state definitions, providing 63 individual states, each with a 64-bit word (one state is reserved). At power-up, the first state is loaded from the SE EEPROM into the engine itself. When the conditions of this state are met, the next state is loaded from the EEPROM into the engine, and so on. The loading of each new state takes approximately 10 s. To alter a state, the required changes must be made directly to the EEPROM. RAM for each state does not exist. The relevant alterations must be made to the 64-bit word, which is then uploaded directly to the EEPROM. INTERNAL REGISTERS The ADM1063 contains a large number of data registers. The principal registers are the address pointer register and the configuration registers. The major differences between the EEPROM and other registers are as follows: * * * The first EEPROM is split into 16 (0 to 15) pages of 32 bytes each. Page 0 to Page 6, starting at Address 0xF800, hold the configuration data for the applications on the ADM1063 (such as the SFDs and PDOs). These EEPROM addresses are the same as the RAM register addresses, prefixed by F8. Page 7 is reserved. Page 8 to Page 15 are for customer use. Data can be downloaded from the EEPROM to the RAM in one of the following ways: * * Address Pointer Register The address pointer register contains the address that selects one of the other internal registers. When writing to the ADM1063, the first byte of data is always a register address that is written to the address pointer register. An EEPROM location must be blank before it can be written to. If it contains data, the data must first be erased. Writing to the EEPROM is slower than writing to the RAM. Writing to the EEPROM should be restricted because it has a limited write/cycle life of typically 10,000 write operations, due to the usual EEPROM wear-out mechanisms. At power-up, when Page 0 to Page 6 are downloaded. By setting Bit 0 of the UDOWNLD register (0xD8), which performs a user download of Page 0 to Page 6. SERIAL BUS INTERFACE The configuration registers provide control and configuration for various operating parameters of the ADM1063. The ADM1063 is controlled via the serial system management bus (SMBus) and is connected to this bus as a slave device, under the control of a master device. It takes approximately 1 ms after power-up for the ADM1063 to download from its EEPROM. Therefore, access to the ADM1063 is restricted until the download is complete. EEPROM Identifying the ADM1063 on the SMBus The ADM1063 has two 512-byte cells of nonvolatile EEPROM from Register Address 0xF800 to Register Address 0xFBFF. The EEPROM is used for permanent storage of data that is not lost when the ADM1063 is powered down. One EEPROM cell contains the configuration data of the device; the other contains the state definitions for the SE. Although referred to as read-only memory, the EEPROM can be written to, as well as read from, using the serial bus in exactly the same way as the other registers. The ADM1063 has a 7-bit serial bus slave address (see Table 11). The device is powered up with a default serial bus address. The five MSBs of the address are set to 00111, and the two LSBs are determined by the logical states of Pin A1 and Pin A0. This allows the connection of four ADM1063s to one SMBus. Configuration Registers Table 11. Serial Bus Slave Address A1 Pin Low Low High High 1 A0 Pin Low High Low High Hex Address 0x38 0x3Ah 0x3Ch 0x3Eh 7-Bit Address 0011100x1 0011101x1 0011110x1 0011111x1 x = Read/Write bit. The address is shown only as the first 7 MSBs. Rev. C | Page 25 of 32 ADM1063 The device also has several identification registers (read-only) that can be read across the SMBus. Table 12 lists these registers with their values and functions. All other devices on the bus remain idle while the selected device waits for data to be read from or written to it. If the R/W bit is a 0, the master writes to the slave device. If the R/W bit is a 1, the master reads from the slave device. Table 12. Identification Register Values and Functions Address 0xF4 0xF5 0xF6 0xF7 Value 0x41 0x02 0x00 0x00 Step 2 Function Manufacturer ID for Analog Devices Silicon revision Software brand Software brand Data is sent over the serial bus in sequences of nine clock pulses: eight bits of data followed by an acknowledge bit from the slave device. Data transitions on the data line must occur during the low period of the clock signal and remain stable during the high period because a low-to-high transition when the clock is high could be interpreted as a stop signal. If the operation is a write operation, the first data byte after the slave address is a command byte. This command byte tells the slave device what to expect next. It may be an instruction telling the slave device to expect a block write, or it may be a register address that tells the slave where subsequent data is to be written. Because data can flow in only one direction, as defined by the R/W bit, sending a command to a slave device during a read operation is not possible. Before a read operation, it may be necessary to perform a write operation to tell the slave what sort of read operation to expect and/or the address from which data is to be read. General SMBus Timing Figure 34, Figure 35, and Figure 36 are timing diagrams for general read and write operations using the SMBus. The SMBus specification defines specific conditions for different types of read and write operations, which are discussed in the Write Operations and Read Operations sections. The general SMBus protocol operates as follows: Step 1 The master initiates data transfer by establishing a start condition, defined as a high-to-low transition on the serial data-line SDA while the serial clock-line SCL remains high. This indicates that a data stream follows. All slave peripherals connected to the serial bus respond to the start condition and shift in the next eight bits, consisting of a 7-bit slave address (MSB first) plus an R/W bit. This bit determines the direction of the data transfer, that is, whether data is written to or read from the slave device (0 = write, 1 = read). Step 3 When all data bytes have been read or written, stop conditions are established. In write mode, the master pulls the data line high during the 10th clock pulse to assert a stop condition. In read mode, the master device releases the SDA line during the low period before the ninth clock pulse, but the slave device does not pull it low. This is known as a no acknowledge. The master then takes the data line low during the low period before the 10th clock pulse and then high during the 10th clock pulse to assert a stop condition. The peripheral whose address corresponds to the transmitted address responds by pulling the data line low during the low period before the ninth clock pulse, known as the acknowledge bit, and by holding it low during the high period of this clock pulse. 1 9 1 9 SCL 0 SDA 0 1 1 1 A1 A0 D7 R/W D6 D5 SDA (CONTINUED) D3 D2 D1 FRAME 2 COMMAND CODE 1 D7 9 D6 D5 D4 D3 D0 ACK. BY SLAVE FRAME 1 SLAVE ADDRESS SCL (CONTINUED) D4 ACK. BY SLAVE START BY MASTER D2 FRAME 3 DATA BYTE D1 D0 1 D7 ACK. BY SLAVE 9 D6 D5 D4 D2 FRAME N DATA BYTE Figure 34. General SMBus Write Timing Diagram Rev. C | Page 26 of 32 D3 D1 D0 ACK. BY SLAVE STOP BY MASTER 04632-036 Name MANID REVID MARK1 MARK2 ADM1063 1 9 1 9 SCL 0 1 1 1 A1 A0 R/W D7 D6 D5 D4 D3 D2 D1 ACK. BY SLAVE START BY MASTER 1 SCL (CONTINUED) SDA (CONTINUED) D7 FRAME 1 SLAVE ADDRESS D6 D5 D4 D3 9 D2 D1 D0 1 D7 FRAME 2 DATA BYTE D6 D5 9 D4 ACK. BY MASTER FRAME 3 DATA BYTE D0 ACK. BY MASTER D3 D2 D1 D0 NO ACK. FRAME N DATA BYTE STOP BY MASTER 04632-037 0 SDA Figure 35. General SMBus Read Timing Diagram tR tF t HD; STA t LO W SCL t HI G H t HD; STA t HD; DAT t SU; STA t SU; STO t SU; DAT t BUF P S S P 04632-038 SDA Figure 36. Serial Bus Timing Diagram SMBus PROTOCOLS FOR RAM AND EEPROM The ADM1063 uses the following SMBus write protocols. The ADM1063 contains volatile registers (RAM) and nonvolatile registers (EEPROM). User RAM occupies Address 0x00 to Address 0xDF; the EEPROM occupies Address 0xF800 to Address 0xFBFF. Send Byte Page erasure is enabled by setting Bit 2 in the UPDCFG register (Address 0x90) to 1. If this bit is not set, page erasure cannot occur, even if the command byte (0xFE) is programmed across the SMBus. 1. 2. 3. 4. 5. 6. In the ADM1063, the send byte protocol is used for two purposes: * WRITE OPERATIONS The SMBus specification defines several protocols for different types of read and write operations. The following abbreviations are used in Figure 37 to Figure 45: * * * * * * S = Start P = Stop R = Read W = Write A = Acknowledge A = No acknowledge The master device asserts a start condition on SDA. The master sends the 7-bit slave address followed by the write bit (low). The addressed slave device asserts an acknowledge (ACK) on SDA. The master sends a command code. The slave asserts an ACK on SDA. The master asserts a stop condition on SDA, and the transaction ends. To write a register address to the RAM for a subsequent single byte read from the same address, or for a block read or a block write starting at that address, as shown in Figure 37. 1 S 2 SLAVE ADDRESS W 3 4 5 6 A RAM ADDRESS (0x00 TO 0xDF) A P 04632-039 Data can be written to and read from both the RAM and the EEPROM as single data bytes. Data can be written only to unprogrammed EEPROM locations. To write new data to a programmed location, the location contents must first be erased. EEPROM erasure cannot be done at the byte level. The EEPROM is arranged as 32 pages of 32 bytes each, and an entire page must be erased. In a send byte operation, the master device sends a single command byte to a slave device, as follows: Figure 37. Setting a RAM Address for Subsequent Read * Rev. C | Page 27 of 32 To erase a page of EEPROM memory. EEPROM memory can be written to only if it is unprogrammed. Before writing to one or more EEPROM memory locations that are already programmed, the page(s) containing those locations must first be erased. EEPROM memory is erased by writing a command byte. ADM1063 W 4 5 6 A COMMAND BYTE (0xFE) A P Figure 38. EEPROM Page Erasure In the ADM1063, the write byte/word protocol is used for three purposes: To write a single byte of data to the RAM. In this case, the command byte is RAM Address 0x00 to RAM Address 0xDF, and the only data byte is the actual data, as shown in Figure 39. 1 2 3 4 5 6 7 8 RAM SLAVE W A S ADDRESS ADDRESS A DATA A P (0x00 TO 0xDF) 04632-041 * * To set up a 2-byte EEPROM address for a subsequent read, write, block read, block write, or page erase. In this case, the command byte is the high byte of EEPROM Address 0xF8 to EEPROM Address 0xFB. The only data byte is the low byte of the EEPROM address, as shown in Figure 40. 2 3 4 5 6 7 8 9 10 EEPROM EEPROM ADDRESS ADDRESS A A DATA A P S SLAVE W A LOW BYTE ADDRESS HIGH BYTE (0x00 TO 0xFF) (0xF8 TO 0xFB) Figure 41. Single Byte Write to the EEPROM Block Write In a block write operation, the master device writes a block of data to a slave device. The start address for a block write must have been set previously. In the ADM1063, a send byte operation sets a RAM address, and a write byte/word operation sets an EEPROM address, as follows: The master device asserts a start condition on SDA. The master sends the 7-bit slave address followed by the write bit (low). 3. The addressed slave device asserts an ACK on SDA. 4. The master sends a command code that tells the slave device to expect a block write. The ADM1063 command code for a block write is 0xFC (1111 1100). 5. The slave asserts an ACK on SDA. 6. The master sends a data byte that tells the slave device how many data bytes are being sent. The SMBus specification allows a maximum of 32 data bytes in a block write. 7. The slave asserts an ACK on SDA. 8. The master sends N data bytes. 9. The slave asserts an ACK on SDA after each data byte. 10. The master asserts a stop condition on SDA to end the transaction. 1. 2. 1 Figure 39. Single Byte Write to the RAM To write a single byte of data to the EEPROM. In this case, the command byte is the high byte of EEPROM Address 0xF8 to EEPROM Address 0xFB. The first data byte is the low byte of the EEPROM address, and the second data byte is the actual data, as shown in Figure 41. 1 Write Byte/Word The master device asserts a start condition on SDA. The master sends the 7-bit slave address followed by the write bit (low). 3. The addressed slave device asserts an ACK on SDA. 4. The master sends a command code. 5. The slave asserts an ACK on SDA. 6. The master sends a data byte. 7. The slave asserts an ACK on SDA. 8. The master sends a data byte or asserts a stop condition. 9. The slave asserts an ACK on SDA. 10. The master asserts a stop condition on SDA to end the transaction. 7 8 Because a page consists of 32 bytes, only the three MSBs of the address low byte are important for page erasure. The lower five bits of the EEPROM address low byte specify the addresses within a page and are ignored during an erase operation. * 1. 2. 6 Figure 40. Setting an EEPROM Address As soon as the ADM1063 receives the command byte, page erasure begins. The master device can send a stop command as soon as it sends the command byte. Page erasure takes approximately 20 ms. If the ADM1063 is accessed before erasure is complete, it responds with a no acknowledge (NACK). In a write byte/word operation, the master device sends a command byte and one or two data bytes to the slave device, as follows: 5 2 3 4 5 6 7 8 9 10 SLAVE COMMAND 0xFC BYTE DATA DATA DATA S ADDRESS W A (BLOCK WRITE) A COUNT A A A A P 1 2 N 04632-044 SLAVE ADDRESS 3 4 04632-043 S 2 3 EEPROM EEPROM ADDRESS ADDRESS A A P S SLAVE W A LOW BYTE ADDRESS HIGH BYTE (0x00 TO 0xFF) (0xF8 TO 0xFB) 04632-040 1 2 04632-042 1 The master sends a command code telling the slave device to erase the page. The ADM1063 command code for a page erasure is 0xFE (1111 1110). Note that for a page erasure to take place, the page address must be given in the previous write word transaction (see the Write Byte/Word section). In addition, Bit 2 in the UPDCFG register (Address 0x90) must be set to 1. Figure 42. Block Write to the EEPROM or RAM Unlike some EEPROM devices that limit block writes to within a page boundary, there is no limitation on the start address when performing a block write to EEPROM, except when * Rev. C | Page 28 of 32 There must be at least N locations from the start address to the highest EEPROM address (0xFBFF) to avoid writing to invalid addresses. ADM1063 * 8. 9. An address crosses a page boundary. In this case, both pages must be erased before programming. Note that the ADM1063 features a clock extend function for writes to EEPROM. Programming an EEPROM byte takes approximately 250 s, which limits the SMBus clock for repeated or block write operations. The ADM1063 pulls SCL low and extends the clock pulse when it cannot accept any more data. 10. 11. 12. 13. READ OPERATIONS 1 The ADM1063 uses the following SMBus read protocols. S The slave asserts an ACK on SDA. The ADM1063 sends a byte-count data byte that tells the master how many data bytes to expect. The ADM1063 always returns 32 data bytes (0x20), which is the maximum allowed by the SMBus Version 1.1 specification. The master asserts an ACK on SDA. The master receives 32 data bytes. The master asserts an ACK on SDA after each data byte. The master asserts a stop condition on SDA to end the transaction. 2 3 4 5 6 7 8 9 10 11 12 SLAVE COMMAND 0xFD SLAVE BYTE DATA R A A A W A A S ADDRESS (BLOCK READ) ADDRESS COUNT 1 Receive Byte 3. 4. 5. 6. The master device asserts a start condition on SDA. The master sends the 7-bit slave address followed by the read bit (high). The addressed slave device asserts an ACK on SDA. The master receives a data byte. The master asserts a NACK on SDA. The master asserts a stop condition on SDA, and the transaction ends. 1 2 S SLAVE ADDRESS R 3 4 5 6 A DATA A P 04632-045 In the ADM1063, the receive byte protocol is used to read a single byte of data from a RAM or EEPROM location whose address has previously been set by a send byte or write byte/word operation, as shown in Figure 43. Figure 43. Single Byte Read from the EEPROM or RAM Block Read In a block read operation, the master device reads a block of data from a slave device. The start address for a block read must have been set previously. In the ADM1063, this is done by a send byte operation to set a RAM address or a write byte/word operation to set an EEPROM address. The block read operation itself consists of a send byte operation that sends a block read command to the slave, immediately followed by a repeated start and a read operation that reads out multiple data bytes, as follows: 1. 2. 3. 4. 5. 6. 7. The master device asserts a start condition on SDA. The master sends the 7-bit slave address followed by the write bit (low). The addressed slave device asserts an ACK on SDA. The master sends a command code that tells the slave device to expect a block read. The ADM1063 command code for a block read is 0xFD (1111 1101). The slave asserts an ACK on SDA. The master asserts a repeat start condition on SDA. The master sends the 7-bit slave address followed by the read bit (high). P Figure 44. Block Read from the EEPROM or RAM Error Correction The ADM1063 provides the option of issuing a packet error correction (PEC) byte after a write to the RAM, a write to the EEPROM, a block write to the RAM/EEPROM, or a block read from the RAM/ EEPROM. This option enables the user to verify that the data received by or sent from the ADM1063 is correct. The PEC byte is an optional byte sent after the last data byte has been written to or read from the ADM1063. The protocol is the same as for a block read for Step 1 to Step 12 and then proceeds as follows: 13. The ADM1063 issues a PEC byte to the master. The master checks the PEC byte and issues another block read if the PEC byte is incorrect. 14. A NACK is generated after the PEC byte to signal the end of the read. 15. The master asserts a stop condition on SDA to end the transaction. Note that the PEC byte is calculated using CRC-8. The frame check sequence (FCS) conforms to CRC-8 by the polynomial C(x) = x8 + x2 + x1 + 1 See the SMBus Version 1.1 specification for details. An example of a block read with the optional PEC byte is shown in Figure 45. 1 2 3 4 5 6 7 8 9 10 11 12 SLAVE COMMAND 0xFD SLAVE BYTE DATA A S ADDRESS W A (BLOCK READ) A S ADDRESS R A COUNT A 1 Rev. C | Page 29 of 32 13 14 15 DATA 32 A PEC A P Figure 45. Block Read from the EEPROM or RAM with PEC 04632-047 1. 2. DATA A 32 04632-046 13 In a receive byte operation, the master device receives a single byte from a slave device, as follows: ADM1063 OUTLINE DIMENSIONS 6.00 BSC SQ 0.60 MAX 0.60 MAX PIN 1 INDICATOR 31 30 TOP VIEW 0.50 BSC 5.75 BSC SQ (BOT TOM VIEW) 0.50 0.40 0.30 12 MAX 1.00 0.85 0.80 21 20 11 10 0.25 MIN 4.50 REF 0.80 MAX 0.65 TYP FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. 0.05 MAX 0.02 NOM SEATING PLANE 4.25 4.10 SQ 3.95 EXPOSED PAD 0.30 0.23 0.18 0.20 REF COPLANARITY 0.08 072108-A PIN 1 INDICATOR 40 1 COMPLIANT TO JEDEC STANDARDS MO-220-VJJD-2 Figure 46. 40-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 6 mm x 6 mm Body, Very Thin Quad (CP-40-1) Dimensions shown in millimeters 0.75 0.60 0.45 1.20 MAX 9.00 BSC SQ 37 36 48 1 PIN 1 0 MIN 1.05 1.00 0.95 0.15 0.05 SEATING PLANE 0.20 0.09 7 3.5 0 0.08 MAX COPLANARITY 7.00 BSC SQ TOP VIEW (PINS DOWN) 12 13 VIEW A VIEW A 0.50 0.27 BSC 0.22 LEAD PITCH 0.17 ROTATED 90 CCW COMPLIANT TO JEDEC STANDARDS MS-026ABC Figure 47. 48-Lead Thin Plastic Quad Flat Package [TQFP] (SU-48) Dimensions shown in millimeters Rev. C | Page 30 of 32 25 24 ADM1063 ORDERING GUIDE Model 1 ADM1063ACPZ ADM1063ACPZ-REEL7 ADM1063ASUZ ADM1063ASUZ-REEL7 EVAL-ADM1063TQEBZ 1 Temperature Range -40C to +85C -40C to +85C -40C to +85C -40C to +85C Package Description 40-Lead LFCSP_VQ 40-Lead LFCSP_VQ 48-Lead TQFP 48-Lead TQFP Evaluation Kit (TQFP Version) Z = RoHS Compliant Part. Rev. C | Page 31 of 32 Package Option CP-40-1 CP-40-1 SU-48 SU-48 ADM1063 NOTES (c)2005-2011 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D04632-0-7/11(C) Rev. C | Page 32 of 32