71M6543F-DB-CT - Maxim Integrated

Page: 1 of 91 v5

71M6543 Demo Board

USER’S MANUAL

Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent

licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.

Maxim Integrated Products, Inc. 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000

 2012 Maxim Integrated Products is a registered trademark of Maxim Integrated Products, Inc.

Page: 2 of 91 v5

71M6543

Polyphase Energy Meter IC

DEMO BOARD REV 4.0 and 5.0

USER’S MANUAL

71M6543 Demo Board User’s Manual

Page: 3 of 91 v5

Table of Contents

1 GETTING STARTED................................................................................................................................................ 7

1.1 General .................................................................................................................................................................... 7

1.2 Safety and ESD Notes ............................................................................................................................................ 7

1.3 Demo Kit Contents ................................................................................................................................................. 8

1.4 Demo Board Versions ............................................................................................................................................ 8

1.5 Compatibility ........................................................................................................................................................... 8

1.6 Suggested Equipment not Included ..................................................................................................................... 8

1.7 Demo Board Test Setup ......................................................................................................................................... 9

1.7.1 Power Supply Setup ........................................................................................................................................ 10

1.7.2 Cables for Serial Communication .................................................................................................................... 10

1.7.3 Checking Operation ......................................................................................................................................... 11

1.7.4 Serial Connection Setup .................................................................................................................................. 11

1.8 Using the Demo Board ......................................................................................................................................... 12

1.8.1 Serial Command Language ............................................................................................................................. 13

1.8.2 Using the Demo Board for Energy Measurements .......................................................................................... 19

1.8.3 Adjusting the Kh Factor for the Demo Board ................................................................................................... 19

1.8.4 Adjusting the Demo Boards to Different SHUNT Resistors ............................................................................. 19

1.8.5 Using the Pre-Amplifier ................................................................................................................................... 19

1.8.6 Using Current Transformers (CTs) .................................................................................................................. 19

1.8.7 Adjusting the Demo Boards to Different Voltage Dividers ............................................................................... 19

1.9 Calibration Parameters ........................................................................................................................................ 20

1.9.1 General Calibration Procedure ........................................................................................................................ 20

1.9.2 Calibration Macro File ..................................................................................................................................... 21

1.9.3 Updating the Demo Code (hex file) ................................................................................................................. 21

1.9.4 Updating Calibration Data in Flash or EEPROM ............................................................................................. 21

1.9.5 Loading the Code for the 71M6543F into the Demo Board ............................................................................. 22

1.9.6 The Programming Interface of the 71M6543F ................................................................................................. 23

1.10 Demo Code ........................................................................................................................................................ 24

1.10.1 Demo Code Description ............................................................................................................................... 24

1.10.2 Demo Code Versions ................................................................................................................................... 24

1.10.3 Important MPU Addresses ........................................................................................................................... 24

1.10.4 LSB Values in CE Registers ........................................................................................................................ 31

1.10.5 Calculating IMAX and Kh ............................................................................................................................. 31

1.10.6 Determining the Type of 71M6x0x ............................................................................................................... 32

1.10.7 Communicating with the 71M6X0x .............................................................................................................. 33

1.10.8 Bootloader Feature ...................................................................................................................................... 33

2 APPLICATION INFORMATION ............................................................................................................................. 35

2.1 Calibration Theory ................................................................................................................................................ 35

2.1.1 Calibration with Three Measurements ............................................................................................................. 35

2.1.2 Calibration with Five Measurements ............................................................................................................... 37

2.2 Calibration Procedures ........................................................................................................................................ 38

2.2.1 Calibration Equipment ..................................................................................................................................... 38

2.2.2 Detailed Calibration Procedures ...................................................................................................................... 38

2.2.3 Calibration Procedure with Three Measurements ........................................................................................... 39

2.2.4 Calibration Procedure with Five Measurements .............................................................................................. 40

2.2.5 Calibration Spreadsheets ................................................................................................................................ 40

2.2.6 Compensating for Non-Linearities ................................................................................................................... 42

2.3 Temperature Compensation ................................................................................................................................ 43

2.3.1 Error Sources .................................................................................................................................................. 43

2.3.2 Software Features for Temperature Compensation ........................................................................................ 44

2.3.3 Calculating Parameters for Compensation ...................................................................................................... 45

2.4 Testing the Demo Board ...................................................................................................................................... 48

71M6543 Demo Board User’s Manual

Page: 4 of 91 v5

2.4.1 Functional Meter Test ...................................................................................................................................... 48

2.4.2 EMC Test ........................................................................................................................................................ 50

2.5 Sensors and Sensor Placement .......................................................................................................................... 50

2.5.1 Self-Heating .................................................................................................................................................... 51

2.5.2 Placement of Sensors (ANSI) ......................................................................................................................... 51

2.5.3 Placement of Sensors (IEC) ............................................................................................................................ 51

2.5.4 Other Techniques for Avoiding Magnetic Crosstalk......................................................................................... 52

3 HARDWARE DESCRIPTION ................................................................................................................................. 55

3.1 71M6543 REV 4.0 Demo Board Description: Jumpers, Switches and Test Points ......................................... 55

3.2 71M6543 REV 5.0 Demo Board Description ....................................................................................................... 59

3.3 Board Hardware Specifications .......................................................................................................................... 60

4 APPENDIX ............................................................................................................................................................. 61

4.1 71M6543 Demo Board Rev 4.0 Electrical Schematic ......................................................................................... 62

4.2 71M6543 Demo Board Rev 5.0 Electrical Schematic ......................................................................................... 66

4.3 Comments on Schematics ................................................................................................................................... 70

4.3.1 General ........................................................................................................................................................... 70

4.3.2 Using Ferrites in the Shunt Sensor Inputs ....................................................................................................... 70

4.4 71M6543 Demo Board REV 4.0 Bill of Material .................................................................................................. 71

4.5 71M6543 Demo Board REV 5.0 Bill of Material .................................................................................................. 73

4.6 71M6543 REV 4.0 Demo Board PCB Layout ....................................................................................................... 75

4.7 71M6543 REV 5.0 Demo Board PCB Layout ....................................................................................................... 79

4.8 Debug Board Bill of Material ............................................................................................................................... 83

4.9 Debug Board Schematics .................................................................................................................................... 84

4.10 Optional Debug Board PCB Layout ................................................................................................................. 85

4.11 71M6543 Pin-Out Information .......................................................................................................................... 88

4.12 Revision History ............................................................................................................................................... 91

List of Figures

Figure 1-1: Teridian 71M6543 REV4.0 Demo Board with Debug Board: Basic Connections .............................................. 9

Figure 1-2: HyperTerminal Sample Window with Disconnect Button (Arrow) ................................................................... 12

Figure 1-3: Port Speed and Handshake Setup (left) and Port Bit setup (right) .................................................................. 12

Figure 1-4: Typical Calibration Macro File ......................................................................................................................... 21

Figure 1-5: Emulator Window Showing Reset and Erase Buttons (see Arrows) ............................................................... 22

Figure 1-6: Emulator Window Showing Erased Flash Memory and File Load Menu ......................................................... 23

Figure 1-7: Worksheet from Calibration Spreadsheets REV 6.0 ....................................................................................... 32

Figure 2-1: Watt Meter with Gain and Phase Errors. ......................................................................................................... 35

Figure 2-2: Phase Angle Definitions .................................................................................................................................. 39

Figure 2-3: Calibration Spreadsheet for Three Measurements ......................................................................................... 41

Figure 2-4: Calibration Spreadsheet for Five Measurements ............................................................................................ 42

Figure 2-5: Non-Linearity Caused by Quantification Noise ............................................................................................... 42

Figure 2-6: Wh Registration Error with VREF Compensation ........................................................................................... 47

Figure 2-7: Wh Registration Error with Combined Compensation ..................................................................................... 48

Figure 2-8: Meter with Calibration System ........................................................................................................................ 49

Figure 2-9: Calibration System Screen ............................................................................................................................. 49

Figure 2-10: Wh Load Lines at Room Temperature with 150 µΩ Shunts .......................................................................... 50

Figure 2-11: VARh Load Lines at Room Temperature with 150 µΩ Shunts ...................................................................... 50

Figure 2-12: Typical Sensor Arrangement (left), Alternative Arrangement (right) ............................................................. 52

Figure 2-13: Swiveled Sensor Arrangement ..................................................................................................................... 52

Figure 2-17: Loop Formed by Shunt and Sensor Wire ...................................................................................................... 53

Figure 2-18: Shunt with Compensation Loop .................................................................................................................... 53

Figure 2-19: Shunt with Center Drill Holes ........................................................................................................................ 53

Figure 3-1: 71M6543 REV 4.0 Demo Board - Board Description ...................................................................................... 58

71M6543 Demo Board User’s Manual

Page: 5 of 91 v5

Figure 3-2: 71M6543 REV 5.0 Demo Board – Top View ................................................................................................... 59

Figure 4-1: Teridian 71M6543 REV 4.0 Demo Board: Electrical Schematic 1/4 ............................................................... 62

Figure 4-2: Teridian 71M6543 REV 4.0 Demo Board: Electrical Schematic 2/4 ............................................................... 63

Figure 4-3: Teridian 71M6543 REV 4.0 Demo Board: Electrical Schematic 3/4 ............................................................... 64

Figure 4-4: Teridian 71M6543 REV 4.0 Demo Board: Electrical Schematic 4/4 ............................................................... 65

Figure 4-5: Teridian 71M6543 REV 5.0 Demo Board: Electrical Schematic 1/4 ............................................................... 66

Figure 4-6: Teridian 71M6543 REV 5.0 Demo Board: Electrical Schematic 2/4 ............................................................... 67

Figure 4-7: Teridian 71M6543 REV 5.0 Demo Board: Electrical Schematic 3/4 ............................................................... 68

Figure 4-8: Teridian 71M6543 REV 5.0 Demo Board: Electrical Schematic 4/4 ............................................................... 69

Figure 4-9: Input Circuit with Ferrites ................................................................................................................................ 70

Figure 4-10: Teridian 71M6543 REV 4.0 Demo Board: Top View ..................................................................................... 75

Figure 4-11: Teridian 71M6543 REV 4.0 Demo Board: Top Copper ................................................................................. 76

Figure 4-12: Teridian 71M6543 REV 4.0 Demo Board: Bottom View ................................................................................ 77

Figure 4-13: Teridian 71M6543 REV 4.0 Demo Board: Bottom Copper ............................................................................ 78

Figure 4-14: Teridian 71M6543 REV 5.0 Demo Board: Top View ..................................................................................... 79

Figure 4-15: Teridian 71M6543 REV 5.0 Demo Board: Top Copper ................................................................................. 80

Figure 4-16: Teridian 71M6543 REV 5.0 Demo Board: Bottom View ................................................................................ 81

Figure 4-17: Teridian 71M6543 REV 5.0 Demo Board: Bottom Copper ............................................................................ 82

Figure 4-18: Debug Board: Electrical Schematic............................................................................................................... 84

Figure 4-19: Debug Board: Top View ................................................................................................................................ 85

Figure 4-20: Debug Board: Bottom View ........................................................................................................................... 85

Figure 4-21: Debug Board: Top Signal Layer .................................................................................................................... 86

Figure 4-22: Debug Board: Middle Layer 1 (Ground Plane) .............................................................................................. 86

Figure 4-23: Debug Board: Middle Layer 2 (Supply Plane) ............................................................................................... 87

Figure 4-24: Debug Board: Bottom Trace Layer ............................................................................................................... 87

Figure 4-25: 71M6543, LQFP100: Pin-out (top view) ........................................................................................................ 90

List of Tables

Table 1-1: Jumper Settings on Debug Board .................................................................................................................... 10

Table 1-2: Straight Cable Connections ............................................................................................................................. 10

Table 1-3: Null-modem Cable Connections ...................................................................................................................... 10

Table 1-4: CE RAM Locations for Calibration Constants .................................................................................................. 21

Table 1-5: Flash Programming Interface Signals .............................................................................................................. 23

Table 1-6: Demo Code Versions ....................................................................................................................................... 24

Table 1-7: MPU XRAM Locations ..................................................................................................................................... 25

Table 1-8: Bits in the MPU Status Word ............................................................................................................................ 30

Table 1-9: CE Registers and Associated LSB Values ....................................................................................................... 31

Table 1-10: IMAX for Various Shunt Resistance Values and Remote Sensor Types ........................................................ 31

Table 1-11: Identification of 71M6x0x Remote Sensor Types ........................................................................................... 33

Table 2-1: Temperature-Related Error Sources ................................................................................................................ 44

Table 2-2: MPU Registers for Temperature-Compensation .............................................................................................. 45

Table 2-3: Temperature-Related Error Sources ................................................................................................................ 46

Table 3-1: 71M6543 REV 4.0 Demo Board Description .................................................................................................... 55

Table 4-1: 71M6543 REV 4.0 Demo Board: Bill of Material (1/2) ...................................................................................... 71

Table 4-2: 71M6543 REV 4.0 Demo Board: Bill of Material (2/2) ...................................................................................... 72

Table 4-3: 71M6543 REV 5.0 Demo Board: Bill of Material (1/3) ...................................................................................... 73

Table 4-4: 71M6543 REV 5.0 Demo Board: Bill of Material (2/3) ...................................................................................... 74

Table 4-5: Debug Board: Bill of Material ........................................................................................................................... 83

Table 4-6: 71M6543 Pin Description Table 1/3 ................................................................................................................. 88

Table 4-7: 71M6543 Pin Description Table 2/3 ................................................................................................................. 88

Table 4-8: 71M6543 Pin Description Table 3/3 ................................................................................................................. 89

71M6543 Demo Board User’s Manual

Page: 6 of 91 v5

71M6543 Demo Board User’s Manual

Page: 7 of 91 v5

1 GETTING STARTED

1.1 GENERAL

The Teridian™ 71M6543 REV 4.0 and REV 5.0 Demo Boards are demonstration boards for evaluating the

71M6543F device for polyphase electronic power metering applications in conjunction with the Remote Sensor

Interface or CT sensors. The Demo Boards allow the evaluation of the 71M6543F energy meter chip for meas-

urement accuracy and overall system use.

The 71M6543 REV 4.0 Demo Board incorporates a 71M6543F integrated circuit, three 71M6103 or 71M6203

Remote Interface ICs, peripheral circuitry such as a serial EEPROM, emulator port, and on-board power supply,

as well as a USB interface for serial communication with a PC.

The 71M6543 REV 5.0 Demo Board is optimized and prepared for the connection of external CTs and is other-

wise identical to the REV 4.0 Demo Board.

All Demo Boards are pre-programmed with a Demo Program (Demo Code) in the FLASH memory of the

71M6543F IC. This embedded application is developed to exercise all low-level function calls to directly man-

age the peripherals, flash programming, and CPU (clock, timing, power savings, etc.).

The 71M6543F IC on the REV 4.0 Demo Board is pre-programmed and pre-calibrated for the 50 µΩ or 120 µΩ

shunts shipped with the board. The Demo Board may also be used for operation with a CT after hardware modi-

fications that can be performed by the user. This configuration will require a different version of the Demo Code

and different settings. It should be noted that the 71M6543 performs better with CTs when used with the

71M6543 REV 5.0 Demo Board.

1.2 SAFETY AND ESD NOTES

Connecting live voltages to the demo board system will result in potentially hazardous voltages on the demo

board.

THE DEMO SYSTEM IS ESD SENSITIVE! ESD PRECAUTIONS SHOULD BE TAKEN

WHEN HANDLING THE DEMO BOARD!

EXTREME CAUTION SHOULD BE TAKEN WHEN HANDLING THE DEMO BOARD

ONCE IT IS CONNECTED TO LIVE VOLTAGES! BOARD GROUND IS CLOSE TO LIVE

VOLTAGE!

Teridian is a trademark of Maxim Integrated Products, Inc.

71M6543 Demo Board User’s Manual

Page: 8 of 91 v5

1.3 DEMO KIT CONTENTS

• 71M6543 Demo Board REV 4.0 with three 71M6203 or 71M6103 ICs and one 71M6543F IC with pre-

loaded demo program, or 71M6543 Demo Board REV 5.0 with inputs configured for CTs.

• 5VDC/1,000mA universal wall transformer with 2.5mm plug (Switchcraft 712A compatible)

• USB Interface Module (USB/Serial Adapter)

• USB cable

• ANSI base with three 50 μΩ shunt resistors, Oswell P/N EBSB20050H-92-19-73-6.4-V1 (optional, for

ANSI kits only)

• Three 120 μΩ shunt resistors, Oswell P/N EBSA15120-32-14.8-21-6.2-V1 (optional, for IEC kits)

1.4 DEMO BOARD VERSIONS

The following versions of the Demo Board are or have been available:

• 71M6543 Demo Board Rev 1.0 (CTs only) - discontinued

• 71M6543 Demo Board Rev 2.0 (CTs or 71M6103 Remote Sensor Interface ICs on daughter boards) -

discontinued

• 71M6543 Demo Board Rev 3.0 (71M6103 Remote Sensor Interface ICs) - discontinued

• 71M6543 Demo Board Rev 4.0 (71M6103 Remote Sensor Interface ICs)

• 71M6543 Demo Board Rev 5.0 (CTs or 71M6103 Remote Sensor Interface ICs

This manual applies to 71M6543 Rev 4.0 and Rev 5.0 only. For the earlier Demo Board revisions please see

their respective manuals.

1.5 COMPATIBILITY

This manual applies to the following hardware and software revisions:

• 71M6543F IC revision B02.

• Demo Code revision 5.4F or later

• 71M6543 Demo Board Rev 4.0 or Rev. 5.0

1.6 SUGGESTED EQUIPMENT NOT INCLUDED

For functional demonstration:

PC with Microsoft Windows versions Windows XP, ME, or 2000, equipped with RS-232 port (COM port) via

DB9 connector

For software development (MPU code):

Signum ICE (In Circuit Emulator): ADM-51

www.signum.com

Signum WEMU51 version 3.11.09 or later should be used. Using a USB isolator between PC and the Signum

ADM-51 is strongly recommended

Keil 8051 “C” Compiler kit: CA51

www.keil.com/c51/ca51kit.htm, www.keil.com/product/sales.htm

Windows and Windows XP are registered trademarks of Microsoft Corp.

71M6543 Demo Board User’s Manual

Page: 9 of 91 v5

1.7 DEMO BOARD TEST SETUP

Figure 1-1 shows the basic connections of the Demo Board REV 4.0 plus optional Debug Board with the exter-

nal equipment. The PC should be connected via the USB Interface (CN1). Communication can also be estab-

lished via the optional Debug Board, but this board is not part of the Demo Kit.

For stand-alone testing (without AC voltage) the Demo Board maybe powered via the 5.0 VDC input (J20). The

optional Debug Board must be powered with its own 5 VDC power supply.

Figure 1-1: Teridian 71M6543 REV4.0 Demo Board with Debug Board: Basic Connections

The Demo Board contains all circuits necessary for operation as a meter, including display, calibration LEDs,

and internal power supply. The optional Debug Board uses a separate power supply, and is optically isolated

from the Demo Board. It interfaces to a PC through a 9 pin serial port connector.

It is recommended to set up the demo board with no live AC voltage connected, and to

connect live AC voltages only after the user is familiar with the demo system.

All input signals are referenced to the V3P3A (3.3V power supply to the chip).

DEMONSTRATION METER

NEUTRAL

IAP

IBP

ICP

V3P3A

GND

V3P3

GND

3.3V DC

Input

EEPROM

ICE Connector

SEGDIO52

SEGDIO10

DB9

to PC

COM Port

6543

Single Chip Meter

TMUXOUT

TMUX2OUT

3.3V or 5V

LCD

SDCK

SDATA

IDP

INEUTRAL

External Shunt

Resistors

IAN

IBN

ICN

V3P3SYS

VARh

SEGDIO0/WPULSE

SEGDIO1/VPULSE

PULSE OUTPUTS

SEGDIO7/YPULSE

SEGDIO6/XPULSE

V3P3SYS

V3P3D

VBAT

Battery 2

(optional)

J13

On-board components

OPTO

5V DC

V5_DBG

GND_DBG

V5_DBG

RS-232

INTERFACE

GND_DBG

V5_DBG

OPTO

FPGA

2/4/2011

V5_NI

CE HEARTBEAT (1Hz)

MPU HEARTBEAT (5Hz)

DEBUG BOARD (OPTIONAL)

RTM INTERFACE

JP21

J21

15, 16

13, 14

5, 7,

9, 11

GND

V3P3SYS

JP6

IDN

PULSE A

PULSE B

SMPS

68 Pin

Connector

VBAT_RTC

Battery 1

(optional)

RESET

JP56

J12

J20

SPI Connector

J14

J19

JP5

CN1

Isolated RS-

232 transceiver

RESET

USB

Interface

71M6103 or 71M6203

Remote Sensor

Interfaces and

isolation transformers

SW4

SEGDIO53

JP53

To PC

71M6543 Demo Board User’s Manual

Page: 10 of 91 v5

1.7.1 POWER SUPPLY SETUP

There are several choices for the meter power supply:

o Internal (using the AC line voltage). The internal power supply is only suitable when the voltage ex-

ceeds 100V RMS. To enable the internal supply, a jumper needs to be installed across JP6 on the top

of the board.

o External 5.0 VDC connector (JP20) on the Demo Board.

1.7.2 CABLES FOR SERIAL COMMUNICATION

It is recommended to use the USB connection to communicate with the Demo Code. The optional Debug

Board is not normally shipped with the Demo Kit and requires a serial port (DB9) on the PC along with a sepa-

rate power supply.

1.7.2.1 USB Connection

A standard USB cable can be used to connect the Demo Board to a PC running HyperTerminal or a similar se-

rial interface program. A suitable driver, e.g. the FTDI CDM Driver Package, must be installed on the PC to en-

able the USB port to be mapped as a virtual COM port. The driver can be found on the FTDI web site

(http://www.ftdichip.com/Drivers/D2XX.htm).

See Table 3-1 for correct placement of jumper JP5 depending on whether the USB connection or the serial

connection via the optional Debug Board is used.

1.7.2.2 Serial Connection (Optional)

For connection of the DB9 serial port of the Debug Board to a PC serial port (COM port), either a straight or a

so-called “null-modem” cable may be used. JP1 and JP2 are plugged in for the straight cable, and JP3/JP4 are

empty. The jumper configuration is reversed for the null-modem cable, as shown in Table 1-1.

Cable Configura-

tion Mode

Jumpers on Debug Board

JP1

JP2

JP3

JP4

Straight Cable

Default

Installed Installed -- --

Null-Modem Cable Alternative -- -- Installed Installed

Table 1-1: Jumper Settings on Debug Board

JP1 through JP4 can also be used to alter the connection when the PC is not configured as a DCE device. Ta-

ble 1-2 shows the connections necessary for the straight DB9 cable and the pin definitions.

PC Pin

Function

Demo Board Pin

2 TX 2

3 RX 3

5 Signal Ground 5

Table 1-2: Straight Cable Connections

Table 1-3 shows the connections necessary for the null-modem DB9 cable and the pin definitions.

PC Pin Function Demo Board Pin

2 TX 3

3 RX 2

5 Signal Ground 5

Table 1-3: Null-modem Cable Connections

See Table 3-1 for correct placement of jumper JP5 on the Demo Board depending on whether the USB connec-

tion or the serial connection via the Debug Board is used.

71M6543 Demo Board User’s Manual

Page: 11 of 91 v5

1.7.3 CHECKING OPERATION

A few seconds after power up, the LCD display on the Demo Board should display a brief greeting in the top

row and the demo code revision in the bottom row:

The “HELLO” message should be followed by the display of accumulated energy:

Wh SYS

The “SYS” symbol will be blinking, indicating activity of the MPU inside the 71M6543.

In general, the fields of the LCD are used as shown below:

Measured value

Unit

Command number

(Phase)

1.7.4 SERIAL CONNECTION SETUP

After connecting the USB cable from the Demo Board to the PC, or after connecting the serial cable from the

optional Debug Board to the PC, start the HyperTerminal application and create a session using the following

parameters:

Port Speed: 9600 bd

Data Bits: 8

Parity: None

Stop Bits: 1

Flow Control: XON/XOFF

When using the USB connection, you may have to define a new port in HyperTerminal after selecting File 

Properties and then clicking on the “Connect Using“ dialog box. If the USB-to-serial driver is installed (see sec-

tion 1.7.2.1) a port with a number not corresponding to an actual serial port, e.g. COM27, will appear in the dia-

log box. This port should be selected for the USB connection.

HyperTerminal can be found by selecting Programs Accessories  Communications from the Windows start

menu. The connection parameters are configured by selecting File  Properties and then by pressing the Con-

figure button. Port speed and flow control are configured under the General tab (Figure 1-3, left), bit settings are

configured by pressing the Configure button (Figure 1-3, right), as shown below. A setup file (file name “Demo

Board Connection.ht”) for HyperTerminal that can be loaded with File  Open is also provided with the tools

and utilities.

In Windows 7 , HyperTerminal is not available, but can be installed from various resources on the Internet.

Port parameters can only be adjusted when the connection is not active. The disconnect

button, as shown in Figure 1-2 must be clicked in order to disconnect the port.

71M6543 Demo Board User’s Manual

Page: 12 of 91 v5

Figure 1-2: HyperTerminal Sample Window with Disconnect Button (Arrow)

Figure 1-3: Port Setup (left) and Port Speed and Handshake Setup (right)

Once, the connection to the demo board is established, press <CR> and the command prompt, >, should ap-

pear. Type >? to see the Demo Code help menu. Type >i to verify the demo code revision.

1.8 USING THE DEMO BOARD

The 71M6543 Demo Board is a ready-to-use meter prepared for use with external shunt resistors.

Demo Code versions for polyphase operation (EQU 5) are available on the Maxim web site (www.maxim-

ic.com) and the 71M6543F is pre-programmed with Demo Code that supports polyphase metering.

Using the Demo Board involves communicating with the Demo Code via the command line interface (CLI). The

CLI allows all sorts of manipulations to the metering parameters, access to the EEPROM, selection of the dis-

played parameters, changing calibration factors and many more operations.

Before evaluating the 71M6543F on the Demo Board, users should get familiar with the commands and re-

sponses of the CLI. A complete description of the CLI is provided in section 1.8.1.

71M6543 Demo Board User’s Manual

Page: 13 of 91 v5

1.8.1 SERIAL COMMAND LANGUAGE

The Demo Code residing in the flash memory of the 71M6543F provides a convenient way of examining and

modifying key meter parameters via its command line interface (CLI).

The tables in this chapter describe the commands in detail.

Commands for CE Data Access:

] CE DATA ACCESS Comment

Description: Allows user to read from and write to CE data space.

Usage: ] [Starting CE Data Address] [option]…[option]

Command

combinations:

]A??? Read consecutive 16-bit words in Decimal, starting at ad-

dress A

]A$$$ Read consecutive 16-bit words in Hex, starting at address A

]A=n=n Write consecutive memory values, starting at address A

]U Update default version of CE Data in flash memory

Example: ]40$$$ Reads CE data words 0x40, 0x41 and 0x42.

]7E=12345678=9876ABCD Writes two words starting @ 0x7E

All CE data words are in 4-byte (32-bit) format. Typing ]A? will access the 32-bit word located at the byte ad-

dress 0x0000 + 4 * A = 0x1028.

Commands for MPU/XDATA Access:

) MPU DATA ACCESS Comment

Description: Allows user to read from and write to MPU data space.

Usage: ) [Starting MPU Data Address] [option]…[option]

Command

combinations:

)A??? Read three consecutive 32-bit words in Decimal, starting at

address A

)A$$$ Read three consecutive 32-bit words in Hex, starting at ad-

dress A

)A=n=m Write the values n and m to two consecutive addresses start-

ing at address A

?) Display useful RAM addresses.

Example: )08$$$$ Reads data words 0x08, 0x0C, 0x10, 0x14

)04=12345678=9876ABCD Writes two words starting @ 0x04

MPU or XDATA space is the address range for the MPU XRAM (0x0000 to 0xFFF). All MPU data words are in 4-byte (32-bit)

format. Typing ]A? will access the 32-bit word located at the byte address 4 * A = 0x28. The energy accumulation registers of

the Demo Code can be accessed by typing two Dollar signs (“$$”), typing question marks will display negative decimal values

if the most significant bit is set.

71M6543 Demo Board User’s Manual

Page: 14 of 91 v5

Commands for DIO RAM (Configuration RAM) and SFR Control:

R DIO AND SFR CONTROL Comment

Description: Allows the user to read from and write to DIO RAM and special function registers (SFRs).

Usage: R [option] [register] … [option]

Command

combinations: RIx… Select I/O RAM location x (0x2000 offset is automatically

added)

Rx… Select internal SFR at address x

Ra???... Read consecutive SFR registers in Decimal, starting at ad-

dress a

Ra$$$... Read consecutive registers in Hex, starting at address a

Ra=n=m… Set values of consecutive registers to n and m starting at

address a

Example: RI2$$$ Read DIO RAM registers 2, 3, and 4 in Hex.

The SFRs (special function registers) are located in internal RAM of the 80515 core, starting at address 0x80.

Commands for EEPROM Control:

EE EEPROM CONTROL Comment

Description: Allows user to enable read from and write to EEPROM.

Usage: EE [option] [arguments]

Command

combinations:

EECn EEPROM Access (1  Enable, 0  Disable)

EERa.b Read EEPROM at address 'a' for 'b' bytes.

EESabc..xyz Write characters to buffer (sets Write length)

EETa Transmit buffer to EEPROM at address 'a'.

EEWa.b...z Write values to buffer

CLS Saves calibration to EEPROM

Example: EEShello

EET$0210

Writes 'hello' to buffer, then transmits buffer to EEPROM start-

ing at address 0x210.

Due to buffer size restrictions, the maximum number of bytes handled by the EEPROM command is 0x40.

Commands for Flash Memory Control:

F FLASH CONTROL Comment

Description: Allows user to enable read from and write to Flash memory.

Usage: F [option] [arguments]

Command

combinations:

FRa.b Read Flash at address 'a' for 'b' bytes.

FSabc..xyz Write characters to buffer (sets Write length)

FTa Transmit buffer to Flash memory at address 'a'.

FWa.b...z Write string of bytes to buffer

Example: FShello

FT$FE10

Writes 'hello' to buffer, then transmits buffer to EEPROM start-

ing at address 0xFE10.

71M6543 Demo Board User’s Manual

Page: 15 of 91 v5

Auxiliary Commands:

Typing a comma (“,”) repeats the command issued from the previous command line. This is very helpful when

examining the value at a certain address over time, such as the CE DRAM address for the temperature (0x40).

The slash (“/”) is useful to separate comments from commands when sending macro text files via the serial in-

terface. All characters in a line after the slash are ignored.

Commands controlling the CE, TMUX and the RTM:

C COMPUTE ENGINE,

MEMORY, AND CALIBRA-

TION CONTROL

Comment

Description: Allows the user to enable and configure the compute engine, store and recall configurations, and

initiate calibration.

Usage: C [option] [argument]

Command

combinations: CEn Compute Engine Enable (1  Enable,

0  Disable)

CTn.m Selects the signal for the TMUX output pins (n = 1 for

TMUXOUT, n = 2 for TMUX2OUT). M is interpreted as a hex

number.

CREn RTM output control (1  Enable, 0  Disable)

CRSa.b.c.d Selects CE addresses for RTM output

CLS Stores calibration and other settings to EEPROM.

CLR Restores calibration and other settings from EEPROM.

CLD Restores calibration and other settings to defaults.

CLB Start auto-calibration based on voltage (MPU address 0x0C,

current (MPU 0x0D), and duration (MPU 0x0E) in seconds.

CLC Apply machine-readable calibration control (Intel Hex-

Records).

CPA Start the accumulating periodic pulse counters.

CPC Clear the pulse counters

CPDn Activate pulse counters for n seconds

Example: CE0 Disables CE, (“SYS will stop blinking on the LCD).

CT1.12 Selects the VBIAS signal for the TMUXOUT pin

Commands for Identification and Information:

I INFORMATION MESSAGES Comment

Description: Allows the user to read information messages.

Usage: I Sends complete demo code version information on serial inter-

face.

M0 Displays meter ID on LCD.

The I command is mainly used to identify the revisions of Demo Code and the contained CE code.

71M6543 Demo Board User’s Manual

Page: 16 of 91 v5

Commands for Battery Mode Control and Battery Test:

B INFORMATION MESSAGES Comment

Description: Allows the user to control battery modes and to test the battery.

Usage: BL Enters LCD mode when in brownout mode (B> prompt).

BS Enters sleep mode when in brownout mode (B> prompt).

BT Starts a battery test – when in mission mode (> prompt).

BWSn Set wake timer to n seconds for automatic return to brownout

mode.

BWMn Set wake timer to n minutes for automatic return to brownout

mode.

Commands for Controlling the RTC:

RT REAL TIME CLOCK CON-

TROL

Comment

Description: Allows the user to read and set the real time clock.

Usage: RT [option] [value] … [value]

Command

combinations: RTDy.m.d.w: Day of week (Year, month, day, weekday [1 = Sunday]). If the weekday is

omitted it is set automatically.

RTR Read Real Time Clock.

RTTh.m.s Time of day: (hr, min, sec).

RTAs.t Real Time Adjust: (start, trim). Allows trimming of the RTC.

If s > 0, the speed of the clock will be adjusted by ‘t’ parts per

billion (PPB). If the CE is on, the value entered with 't' will be

changing with temperature, based on Y_CAL, Y_CALC and

Y_CALC2.

> Access look-up table for RTC compensation.

Example: RTD05.03.17.5 Programs the RTC to Thursday, 3/17/2005

RTA1.+1234 Speeds up the RTC by 1234 PPB.

>0???? Read the first four bytes in the look-up table.

The “Military Time Format” is used for the RTC, i.e. 15:00 is 3:00 PM.

Commands for Accessing the Trim Control Registers:

T TRIM CONTROL Comment

Description: Allows user to read trim and fuse values.

Usage: T [option]

Command

combinations:

T4 Read fuse 4 (TRIMM).

T5 Read fuse 5 (TRIMBGA)

T6 Read fuse 6 (TRIMBGB).

Example: T4 Reads the TRIMM fuse.

These commands are only accessible for the 71M6543H (0.1%) parts. When used on a 71M6543F (0.5%) part,

the results will be displayed as zero.

71M6543 Demo Board User’s Manual

Page: 17 of 91 v5

Reset Commands:

W RESET Comment

Description: Watchdog control

Usage: W Halts the Demo Code program, thus suppressing the trigger-

ing of the hardware watchdog timer. This will cause a reset, if

the watchdog timer is enabled.

Commands for the 71M6x0x Remote Sensor Interface:

6 71M6x0x Interface Comment

Description: Commands for control of the Re-

mote Sensor Interface IC.

Usage: 6En Remote sensor Enable (1  Enable, 0  Disable)

6Ra.b Read Remote Sensor IC number a with command b.

6Ca.b Write command b to Remote Sensor IC number a.

6Ta.b Send command b to Remote Sensor IC number a in a loop

forever.

6T Send temp command to 6000 number 2 in a loop forever.

6R1.20 Reads the temperature from Remote Sensor IC number 1.

See section 1.10.7 for information on how to interpret the

temperature data.

71M6543 Demo Board User’s Manual

Page: 18 of 91 v5

Commands for Controlling the Metering Values Shown on the LCD Display:

Step

Text or Nu-

merical Dis-

play

CLI

command Displayed Parameter(s)

0 10000

00 M0 Meter ID

1 24.5 °C

01 M1 Temperature difference from calibration temperature. Displayed in

0.1°C

2 59.9

02 M2 Frequency at the VA_IN input [Hz]

3 3.27 Wh

03 M3 Accumulated imported real energy [Wh]. The default display setting

after power-up or reset.

1.04 Wh

M4 Accumulated exported real energy [Wh].

2.21 VARh

M5 Accumulated reactive energy [VARh].

0.95 VARh

M6 Accumulated exported reactive energy [VARh].

4.11 VAh

M7 Accumulated apparent energy [VAh].

0.7 h

M8 Elapsed time since last reset or power up.

01:43:59

M9 Time of day (hh.mm.ss)

01.01.01

M10 Date (yy.mm.dd)

0.62

M11.P Power factor (P = phase)

12 0 M12 Not used in the 71M6543

120

M13 Zero crossings of the mains voltage

M14 Duration of sag or neutral current [s]

29.98 A

29.91 A

30.02 A

M15 RMS current (P = phase). “M15.4” displays the neutral current.

240.27 V

239.43 V

240.04 V

M16 RMS voltage

3.34 V

M17 Battery voltage

241.34 W

240.92 W

241.01 W

M18 Momentary power in W (P = phase)

50400 W

M19 Demand

88.88.88

M20 LCD Test

Displays for total consumption wrap around at 999.999Wh (or VARh, VAh) due to the limited number of avail-

able display digits. Internal registers (counters) of the Demo Code are 64 bits wide and do not wrap around.

71M6543 Demo Board User’s Manual

Page: 19 of 91 v5

1.8.2 USING THE DEMO BOARD FOR ENERGY MEASUREMENTS

The 71M6543 Demo Board was designed for use with shunt resistors connected via the Remote Sensor Inter-

faces and it is shipped in this configuration.

The Demo Board may immediately be used with 50 µΩ shunt resistors (ANSI version) or 120 µΩ shunt resistors

(IEC version). It is programmed for a kh factor of 3.2 (see Section 1.8.4 for adjusting the Demo Board for

shunts with different resistance).

Once, voltage is applied and load current is flowing, the red LED D5 will flash each time an energy sum of 3.2

Wh is collected. The LCD display will show the accumulated energy in Wh when set to display mode 3 (com-

mand >M3 via the serial interface).

Similarly, the red LED D6 will flash each time an energy sum of 3.2 VARh is collected. The LCD display will

show the accumulated energy in VARh when set to display mode 5 (command >M5 via the serial interface).

1.8.3 ADJUSTING THE KH FACTOR FOR THE DEMO BOARD

The 71M6543 Demo Board is shipped with a pre-programmed scaling factor Kh of 3.2, i.e. 3.2 Wh per pulse. In

order to be used with a calibrated load or a meter calibration system, the board should be connected to the AC

power source using the spade terminals on the bottom of the board. On the revision REV 4.0 of the Demo

Board, the shunt resistor wires are terminated directly to the dual-pin headers J22, J23, and J24 on the board.

The Kh value can be derived by reading the values for IMAX and VMAX (i.e. the RMS current and voltage val-

ues that correspond to the 250mV maximum input signal to the IC), and inserting them in the following equation

for Kh:

Kh = 54.5793*VMAX*IMAX / (SUM_SAMPS*WRATE*X),

See the explanation in section 1.10.5 for an exact definition of the constants and variables involved in the equa-

tion above.

1.8.4 ADJUSTING THE DEMO BOARDS TO DIFFERENT SHUNT RESISTORS

The Demo Board REV 4.0 is prepared for use with 120 µΩ or 50 µOhm (ANSI option) shunt resistors in all cur-

rent channels. A certain current flowing through the 120 µΩ shunt resistors will result in the maximum voltage

drop at the ADC of the 71M6103 Remote Sensor ICs. This current is defined as IMAX and can be adjusted at

MPU location 0x03 (see section 1.10.3).

IMAX will need to be changed when different values are used for the shunt resistor(s) which will require that

WRATE has to be updated as shown in section 1.10.5.

The scaling of the neutral current measurement is controlled by the i_max2 variable at MPU location 0x01C.

1.8.5 USING THE PRE-AMPLIFIER

In its default setting, the 71M6543F applies a gain of 1 to the current input for the neutral current inputs

(IAP/IAN pins). This gain is controlled with the PRE_E bit in I/O RAM (see the Data Sheet). The command line

interface (RI command) can be used to set or reset this bit. It is recommended to maintain the gain of setting of

1 (RI2704=0x90).

1.8.6 USING CURRENT TRANSFORMERS (CTS)

All phases of the 71M6543 REV 5.0 Demo Board are equipped with connectors for external CTs. CTs should be

connected to the headers J5, J7, and J10. A burden resistor of 1.7 Ω is installed at the R26, R27, and R31 (and

corresponding resistors for phases B and C) locations. With a 2000:1 ratio CT, the maximum current will be 208

For the CT configuration, a shunt resistor of 50 µΩ should be installed to measure the neutral current. Different

values can be accommodated by changing the value of i_max2 at MPU location 0x1C (see section 1.10.3).

Note: The CT configuration requires a different version of the Demo Code than is used for the shunt

configuration.

1.8.7 ADJUSTING THE DEMO BOARDS TO DIFFERENT VOLTAGE DIVIDERS

The 71M6543 Demo Board comes equipped with its own network of resistor dividers for voltage measurement

mounted on the PCB. The resistor values (for the 71M6543 REV 2.0 Demo Board) are 2.5477MΩ (R66, R64,

R47, R39 combined) and 750Ω (R32, R52, R72), resulting in a ratio of 1:3,393.933. This means that VMAX

equals 176.78mV*3,393.933 = 600V. A large value for VMAX has been selected in order to have headroom for

71M6543 Demo Board User’s Manual

Page: 20 of 91 v5

over-voltages. This choice need not be of concern, since the ADC in the 71M6543F has enough resolution,

even when operating at 120 Vrms or 240 Vrms.

If a different set of voltage dividers or an external voltage transformer (potential transformer) is to be used,

scaling techniques should be used.

In the following example we assume that the line voltage is not applied to the resistor divider for VA formed by

R66, R64, R47, R39, and R32, but to a voltage transformer with a ratio N of 20:1, followed by a simple resistor

divider. We also assume that we want to maintain the value for VMAX at 600V to provide headroom for large

voltage excursions.

When applying VMAX at the primary side of the transformer, the secondary voltage Vs is:

Vs = VMAX / N

Vs is scaled by the resistor divider ratio RR. When the input voltage to the voltage channel of the 71M6543 is the

desired 177mV, Vs is then given by:

Vs = RR * 176.8 mV

Resolving for RR, we get:

RR = (VMAX / N) / 176.8 mV = (600V / 30) / 176.8 mV = 170.45

This divider ratio can be implemented, for example, with a combination of one 16.95 kΩ and one 100 Ω resistor.

If potential transformers (PTs) are used instead of resistor dividers, phase shifts will be introduced that will re-

quire negative phase angle compensation. Teridian Demo Code accepts negative calibration factors for phase.

1.9 CALIBRATION PARAMETERS

1.9.1 GENERAL CALIBRATION PROCEDURE

Any calibration method can be used with the 71M6543F ICs. This Demo Board User’s Manual presents calibra-

tion methods with three or five measurements as recommended methods, because they work with most manual

calibration systems based on counting "pulses" (emitted by LEDs on the meter).

Naturally, a meter in mass production will be equipped with special calibration code offering capabilities beyond

those of the 71M6543 Demo Code. It is basically possible to calibrate using voltage and current readings, with

or without pulses involved. For this purpose, the MPU Demo Code should be modified to display averaged volt-

age and current values (as opposed to momentary values). Also, automated calibration equipment can com-

municate with the Demo Boards via the serial interface and extract voltage and current readings. This is possi-

ble even with the unmodified Demo Code.

Complete calibration procedures are given in section 2.2 of this manual.

Regardless of the calibration procedure used, parameters (calibration factors) will result that will have to be ap-

plied to the 71M6543F IC in order to make the chip apply the modified gains and phase shifts necessary for ac-

curate operation. Table 1-4 shows the names of the calibration factors, their function, and their location in the

CE RAM.

Again, the command line interface can be used to store the calibration factors in their respective CE RAM ad-

dresses. For example, the command

>]10=+16302

stores the decimal value 16302 in the CE RAM location controlling the gain of the current channel (CAL_IA).

The command

>]11=4005

stores the hexadecimal value 0x4005 (decimal 16389) in the CE RAM location controlling the gain of the volt-

age channel (CAL_VA).

71M6543 Demo Board User’s Manual

Page: 21 of 91 v5

Table 1-4: CE RAM Locations for Calibration Constants

Coefficient

CE Ad-

dress

(hex)

Description

CAL_VA

CAL_VB

CAL_VC

0x11

0x14

0x17

Adjusts the gain of the voltage channels. +16384 is the typical value. The

gain is directly proportional to the CAL parameter. Allowed range is 0 to

32767. If the gain is 1% slow, CAL should be increased by 1%.

CAL_IA

CAL_IB

CAL_IC

0x10

0x13

0x16

Adjusts the gain of the current channels. +16384 is the typical value. The

gain is directly proportional to the CAL parameter. Allowed range is 0 to

32767. If the gain is 1% slow, CAL should be increased by 1%.

LCOMP2_A

LCOMP2_B

LCOMP2_C

0x12

0x15

0x18

This constant controls the phase compensation. No compensation occurs

when LCOMP2_n=16384. As LCOMP2_n is increased, more compensa-

tion is introduced.

CE codes for CT configuration do not use delay adjustment. These codes

use phase adjustment (PHADJ_n).

1.9.2 CALIBRATION MACRO FILE

The macro file in Figure 1-4 contains a sequence of the serial interface commands. It is a simple text file and

can be created with Notepad or an equivalent ASCII editor program. The file is executed with HyperTerminal’s

Transfer->Send Text File command.

Figure 1-4: Typical Calibration Macro File

It is possible to send the calibration macro file to the 71M6543F for “temporary” calibration. This will temporarily

change the CE data values. Upon power up, these values are refreshed back to the default values stored in

flash memory. Thus, until the flash memory is updated, the macro file must be loaded each time the part is

powered up. The macro file is run by sending it with the transfer



send text file procedure of HyperTerminal.

Use the Transfer



Send Text File command!

1.9.3 UPDATING THE DEMO CODE (HEX FILE)

The d_merge program updates the hex file (for example 6543eq5_6103_5p3c_01nov10.hex, or similar) with the

values contained in the macro file. This program is executed from a DOS command line window. Executing the

d_merge program with no arguments will display the syntax description. To merge macro.txt and

old_6543_demo.hex into new_6543_demo.hex, use the command:

d_merge old_6543_demo.hex macro.txt new_6543_demo.hex

The new hex file can be written to the 71M6543F/71M6543H through the ICE port using the ADM51 in-circuit

emulator or the TFP-2 flash programmer.

1.9.4 UPDATING CALIBRATION DATA IN FLASH OR EEPROM

It is possible to make data permanent that had been entered temporarily into the CE RAM. The transfer to

EEPROM memory is done using the following serial interface command:

>]CLS

Thus, after transferring calibration data with manual serial interface commands or with a macro file, all that has

to be done is invoking the U command.

CE0 /disable CE

]10=+16022 /CAL_IA (gain=CAL_IA/16384)

]11=+16381 /CAL_VA (gain=CAL_VA/16384)

]12=+17229 /LCOMP2_A (default 16384)

CE1 /enable CE

71M6543 Demo Board User’s Manual

Page: 22 of 91 v5

Similarly, calibration data can be restored to default values using the CLD command.

After reset, calibration data is copied from the EEPROM, if present. Otherwise, calibration

data is copied from the flash memory. Writing 0xFF into the first few bytes of the EEPROM

deactivates any calibration data previously stored to the EEPROM.

1.9.5 LOADING THE CODE FOR THE 71M6543F INTO THE DEMO BOARD

Hardware Interface for Programming: The 71M6543F IC provides an interface for loading code into the inter-

nal flash memory. This interface consists of the following signals:

E_RXTX (data), E_TCLK (clock), E_RST (reset), ICE_E (ICE enable)

These signals, along with V3P3D and GND are available on the emulator headers J14.

Programming of the flash memory requires a specific in-circuit emulator, the ADM51 by Signum Systems or the

Flash Programmer (TFP-2) provided by Maxim.

Chips may also be programmed before they are soldered to the board. Gang programmers suitable for high-

volume production are available from BPM Microsystems.

In-Circuit Emulator: If firmware exists in the 71M6543F flash memory; it has to be erased before loading a new

file into memory. Figure 1-5 and Figure 1-6 show the emulator software active. In order to erase the flash

memory, the RESET button of the emulator software has to be clicked followed by the ERASE button.

To successfully erase the flash memory, the following steps have to be taken:

1) Disable the CE by writing 0x00 to address 0x2000

2) Write 0x20 to address 0x2702 (FLSH_UNLOCK[ ] register in I/O RAM)

3) Reset the demo board (RESET button or power cycle)

4) Activate the ERASE button in the WEMU51 user interface

5) Now, new code can be loaded into the flash memory

Once the flash memory is erased, the new file can be loaded using the commands File followed by Load. The

dialog box shown in Figure 1-6 will then appear making it possible to select the file to be loaded by clicking the

Browse button. Once the file is selected, pressing the OK button will load the file into the flash memory of the

71M6543F IC. At this point, the emulator probe (cable) can be removed. Once the 71M6543F IC is reset using

the reset button on the Demo Board, the new code starts executing.

Figure 1-5: Emulator Window Showing Reset and Erase Buttons (see Arrows)

71M6543 Demo Board User’s Manual

Page: 23 of 91 v5

Figure 1-6: Emulator Window Showing Erased Flash Memory and File Load Menu

Flash Programmer Module (TFP-2): The operational firmware of the TFP2 will have to be upgraded to revision

1.53. Follow the instructions given in the User Manual for the TFP-2.

1.9.6 THE PROGRAMMING INTERFACE OF THE 71M6543F

Flash Downloader/ICE Interface Signals

The signals listed in Table 1-5 are necessary for communication between the TFP2 Flash Downloader or ICE

and the 71M6543F.

Signal Direction Function

ICE_E Input to the 71M6543F ICE interface is enabled when ICE_E is

pulled high

E_TCLK Output from 71M6543F Data clock

E_RXTX Bi-directional Data input/output

E_RST Bi-directional Flash Downloader Reset (active low)

Table 1-5: Flash Programming Interface Signals

The E_RST signal should only be driven by the Flash Downloader when enabling these interface

signals. The Flash Downloader must release E_RST at all other times.

71M6543 Demo Board User’s Manual

Page: 24 of 91 v5

1.10 DEMO CODE

1.10.1 DEMO CODE DESCRIPTION

The Demo Board is shipped preloaded with Demo Code in the 71M6543F chip. The code revision can easily be

verified by entering the command >i via the serial interface (see section 1.8.1). Check with your local Maxim re-

presentative/FAE or for the latest revision, or obtain the latest revision from the Maxim web site.

The Demo Code offers the following features:

• It provides basic metering functions such as pulse generation, display of accumulated energy, fre-

quency, date/time, and enables the user to evaluate the parameters of the metering IC such as accu-

racy, harmonic performance, etc.

• It maintains and provides access to basic household functions such as the real-time clock (RTC).

• It provides access to control and display functions via the serial interface, enabling the user to view

and modify a variety of meter parameters such as Kh, calibration coefficients, temperature compensa-

tion etc.

• It provides libraries for access of low-level IC functions to serve as building blocks for code de-

velopment.

A detailed description of the Demo Code can be found in the Software User’s Guide (SUG). In addition, the

comments contained in the library provided with the Demo Kit can serve as useful documentation.

The Software User’s Guide contains the following information:

• Design guide

• Design reference for routines

• Tool Installation Guide

• List of library functions

• 80515 MPU Reference (hardware, instruction set, memory, registers)

1.10.2 DEMO CODE VERSIONS

Each sensor configuration has its own Demo Codes version. Using the wrong type of Demo Code will result in

malfunction. Table 1-6 shows the available Demo Code versions and their application.

Table 1-6: Demo Code Versions

File Name

Supported Configuration

Supported Demo Board

6543equ5_6103_5p3d_14feb11.hex

3 x 71M6103 with shunts 71M6543 DB REV4-0

6543equ5_6113_5p3d_14feb11.hex

3 x 71M6113 with shunts 71M6543 DB REV4-0

6543equ5_6203_5p3d_14feb11.hex

3 x 71M6203 with shunts 71M6543 DB REV4-0

6543equ5_6603_5p3d_14feb11.hex

3 x 71M6603 with shunts 71M6543 DB REV4-0

6543equ5_ct_5p3d_14feb11.hex

CT 71M6543 DB REV5-0

1.10.3 IMPORTANT MPU ADDRESSES

In the Demo Code, certain MPU XRAM parameters have been given addresses in order to permit easy external

access. These variables can be read via the command line interface (if available), with the )n$ command and

written with the )n=xx command where n is the word address. Note that accumulation variables are 64 bits long

and are accessed with )n$$ (read) and )n=hh=ll (write) in the case of accumulation variables.

The first part of the table, the addresses )00..)1F, contains adjustments, i.e. numbers that may need adjustment

in a demonstration meter, and so are part of the calibration for demo code. In a reference meter, these may be

in an unchanging table in code space.

The second part, )20..)2F, pertains to calibration, i.e. variables that are likely to need individual adjustments for

quality production meters.

The third part, )30…, pertains to measurements, i.e. variables and registers that may need to be read in a

demonstration meter.

71M6543 Demo Board User’s Manual

Page: 25 of 91 v5

Table 1-7: MPU XRAM Locations

Name Purpose LSB Default )? Signed? Bits

i_min

Metering element

enters creep mode

if current is below

this value.

If 0, creep logic is

disabled. In creep

mode, on each me-

tering element, Wh,

VARh, i0sqsum,

and other items are

zeroed.

Same units as CE’s i0sqsum. 0.08A )0 signed 32

cfg Configure meter

operation on the fly.

bit0: 1=Display KWh.

bit1: 1=clear accumulators, er-

rors, etc. (e.g. “)1=2”)

bit2: 1=Reset demand. (e.g.

“)1=4”)

bit3: 1=CE Raw mode. MPU

does not change CE values with

creep or small current calcula-

tions.

bit5: 1= Send a message once

per second for IEC 62056-217

Mode D on UART 1, at 2400

BAUD, even parity. The meter’s

serial number and current Wh

display are sent as data. UART

1 is routed to an IR LED if pos-

sible. Mode D data fields are

prefaced with OBIS codes in

legacy format. 7,1

bit6: 1=Auto calibration mode 1

bit7: 1=Enable Tamper Detect

2,1

Do nothing spe-

cial.

)1 N/A 8

v_min

error if below. Also

creep.*

Below this, low volt-

age seconds are

counted. Voltage,

Wh, VARh, Fre-

quency, and other

voltage-dependent

items are zeroed.

Same units as CE’s v0sqsum. 40V )2 signed 32

i_max

Scaling Maximum

Amps for standard

sensor.

0.1A

110.5 for 200

μOhm shunt

with 8x preamp.

884.0 A for 200

μOhm shunt,

442.0A for 400

μOhm shunt.

)3 signed 16

v_max Scaling Maximum

Volts for PCB 0.1V 600 V, for the

Demo Board. )4 signed 16

i_limit Error if exceeded. Same units as CE’s i0sqsum.

50.9A =

30A*sqrt(2)

*120%

)5 signed 32

v_limit Error if exceeded.* Same units as CE’s v0sqsum.

407.3V =

240V*sqrt(2)

*120%

)6 signed 32

71M6543 Demo Board User’s Manual

Page: 26 of 91 v5

wrate_mpu Convert from CE

counts to pulses.

CE’s w0sum units per pulse,

rounded up to next largest CE

count so Wh accumulation and

display is always rounded down.

3.2 Wh )7 signed 32

interval

The number of

minutes of a de-

mand interval.

Count of minutes.

(60/interval)*interval = 60. 2 minutes )8 unsigned 8

mains_hz

Expected number of

cycles per second

of mains. 0 disables

the software RTC

run from mains.

Hz 0 )9 unsigned 8

temp_cal1

Machine-readable

units per 0.1C

See data sheet. Temperature is

calculated as temp = (meas-

ured_temp – temp_datum)

/temp_cal1 + temp_cal0

See data sheet. )A signed 32

mtr_cal1

[0..3]9

Linear temperature

calibration for meter

elements A..D.

ppm*(T - mtr_datum), in 0.1˚C 150 )B..E signed 16

mtr_cal2

[0..3]9

Squared tempera-

ture calibration for

meter elements

A..D.

ppm2*(T - mtr_datum)2, in 0.1˚C -392 )F..1

2 signed 16

y_datum Center temperature

of the crystal. 0.1 C 25C )13 signed 16

y_cal1 5 RTC adjust, linear

by temp. 10 ppb*(T - y_datum), in 0.1˚C 0 )14 signed 16

y_cal2 5 RTC adjust,

squared by temp. 1 ppb*(T - y_datum)2, in 0.1˚C 38 )15 signed 16

s_cal 1

Accumulation inter-

vals of

Autocalibration

Count of accumulation intervals

of calibration.

accumulation

intervals cover

both chop polar-

ities.

)C signed 16

v_cal 1 Volts of

Autocalibration

0.1 V rms of AC signal applied

to all elements during calibra-

tion.

2400

240 V is the

default full-scale

for meter test.

)D signed 16

i_cal 1 Amps of

Autocalibration

0.1 A rms of AC signal applied

to all elements during calibra-

tion. Power factor of calibration

signal must be 1.

300

30 A is the de-

fault full-scale

for meter test.

)E signed 16

71M6543 Demo Board User’s Manual

Page: 27 of 91 v5

lcd_idx Selects LCD’s cur-

rent display.

0: Meter identification. (“#”)

1: Display variation from calibra-

tion temperature, 0.1C

2: Display mains Hz, 0.1 Hz

3: mWh, total

4: mWh total exported.

5: mVARh, total.

6: mVARh, total exported.

7:mVAh, total

8: Operating hours.

9: Time of day

10: Calendar date

11: Power factor, total

12: Angle between phase 0 & 1

13: Main edge count, last accu-

mulation.

14: KW, instantaneous total

15: V, instantaneous max of all

phases.

16: A, total

17: V, Battery (“VB”)

18: Seconds, bad power (“BPS”)

19: Seconds, tamper (- = tamper

in progress) (“TS”)

20: LCD Test

Scrolling not standard for these:

111: PF, phase 0

112: Angle, phase 0 & 1

114: KW, phase 0

115: V, phase 0

116: A, phase 0

211: PF, phase 1

212: Angle, phase 0 & 2

214: KW, phase 1

215: V, phase 1

216: A, phase 1

311: PF, phase 2

312: Angle, phase 2.0

314: KW, phase 2

315: V, phase 2

316: A, phase 2

416: A, neutral (measured)

3 )19 signed 16

lcd_bit Defines sequence

of LCD displays.

The value is a bit mask that de-

scribes a scrolling display se-

quence. Each set bit permits a

display with an lcd_idx value

from 0..31. Each is displayed

for 7 seconds. Ordered by in-

creasing bit number. If value is

zero, display does not change.

0 )1A unsigned 32

mfr_id 6

Manufacturer’s ID

text string of the

meter

3 ASCII bytes, in MSB of 32-bit

number. Least significant byte

should be zero. For AMR

demonstrations, sent as the

manufacturer’s ID of the meter.

“TSC”,

0x54534300 )1B unsigned 32

71M6543 Demo Board User’s Manual

Page: 28 of 91 v5

i_max2 4

Like i_max, except

for the 2nd current

sensor.

Currents, Wh etc.

using currents from

the second sensor

are rescaled into the

same units as the

first current sensor.

0.1 Amps 208 A (2080) )1C signed 16

in_limit 3 Maximum valid neu-

tral current. Same units as CE’s i3sqsum. 0.1A )1D signed 32

in_wait 3

The time that neu-

tral current can ex-

ceed n_max before

the neutral error is

asserted.

Count of accumulation intervals. 10 secs. )1E signed 16

Reserved )1F

meter_id 8 Identification num-

ber of meter.

32 bit unsigned number. For

AMR demonstrations, this is

sent in decimal as the identifica-

tion number of the meter.

100000000 )20 signed 32

temp_datum 8

Count of tempera-

ture sensor at cali-

bration.

See data sheet. Temperature is

calculated as temp = (meas-

ured_temp –

temp_datum)/temp_cal1 +

temp_cal0

n/a )21 signed 32

mtr_datum[0.

.3]8

Center temperature

of a meter element’s

temperature curve.

0.1C 22C )22..

25 signed 16

rtca_adj 8

Default value for

RTCA_ADJ, the

crystal’s capacitor

adjustment.

See data sheet. Set from hard-

ware value when hardware is

changed.

Hardware de-

fault (see data

sheet).

)26 unsigned 8

y_cal0 5,8 RTC offset rate ad-

just 100ppb 0 )27 signed 16

v_bat_min 8 Minimum valid bat-

tery voltage.

Units of hardware’s battery

measurement register.

2V on a real

PCB; should be

adjusted for

battery and

chip.

)28 signed 32

cal_cnt

Count of calibra-

tions. In demo

code, it also checks

adjustments.

Counts number of times calibra-

tion is saved, to a maximum of

255.

0 )29 unsigned 8

ver_hash

Checked to prevent

old calibration data

from being used by

new code. Value

that changes with

the banner text, and

therefore with the

version, date and

time.

Uses data_ok() to calculate a

value from the string. n/a )2A unsigned 8

data_ok_cal

Checks calibrations.

In demo code, it

also checks adjust-

ments.

Checked by data_ok() of calibra-

tion value. n/a )2B unsigned 16

Reserved )2C.

)2F

71M6543 Demo Board User’s Manual

Page: 29 of 91 v5

state_bit_ar

Status of meter.

Nonvolatile.

Bits:

See table below. 0 = no errors )30 unsigned 32

wh_im Wh energy register.

Nonvolatile.

First 32-bit number is a count of

pulses, =3.2 Wh in 3-phase me-

ters, or 1 in 1-phase. A frac-

tional pulse is present in the CE

data, but not preserved.

n/a )31 64

wh_ex

Wh exported energy

tile.

Like wh_im n/a )32 64

varh_im VARh register.

Nonvolatile. Like wh_im n/a )33 64

varh_ex VARh exported reg-

ister. Nonvolatile. Like wh_im n/a )34 64

dmd_max Maximum demand,

W Units of w0sum n/a )35 signed 32

dmd_max_rtc Time of maximum

demand.

Standard time and date struc-

ture.

year, month,

date, hour, min

)36..

3A unsigned 7x8

v_bat

Battery voltage at

last measurement.

Volatile; not saved

on power failure.

0.1V n/a )3B signed 8

acc_cnt

Count of accumula-

tion intervals since

reset, or last clear.

Cleared with )1=2 or

meter read. Volatile;

not saved on power

failure.

count n/a )3C signed 32

tamper_sec

Counts seconds

that tamper errors

were asserted.

Cleared with )1=2 or

meter read. Nonvol-

atile.

This is a tamper measurement. n/a )3D signed 32

sag_sec

Counts seconds

that voltage low

error occurred. or

meter read. Nonvol-

atile.

This is a power quality meas-

urement. n/a )3E signed 32

in_sec 3

Counts seconds

that neutral current

error was asserted.

Cleared with )1=2 or

meter read. Nonvol-

atile.

This is a power quality meas-

urement. n/a )3F signed 32

rtc_copy

Clock time and date

when data was last

read from the RTC.

Standard time and date struc-

ture. year, month, date, hour,

min, sec

n/a )40..

45 unsigned 8*7

save_cnt Number of power

data_ok_reg

Checks data. n/a n/a )47 unsigned 16

1 Valid only when autocalibration is integrated. Meters with metering equations with differential currents or voltages do

not normally support autocalibration.

2 Requires features not in some demo PCBs.

71M6543 Demo Board User’s Manual

Page: 30 of 91 v5

3 Three-phase ICs only. Some CE codes calculate neutral current rather than measuring it. Consult the CE documenta-

tion.

4 Only in systems with two current sensors.

5 High accuracy use of this feature may require a calibrated clock.

6 IEC 62056 Manufacturers’ IDs are allocated by the FLAG association. Maxim does not own or profit from the FLAG

association. Maxim’s default id may not conform, and is for demonstration purposes only.

7 Nothing in the document should be interpreted as a guarantee of conformance to a 3rd party software specification.

Conformance testing is the responsibility of a meter manufacturer.

8 May require calibration for best accuracy.

9 Calibration item in high-precision “H” series meters (71M6543H only).

Table 1-8: Bits in the MPU Status Word

Name Bit

No.

Explanation

MINIA

IA is below IThrshld. Current for this phase is in creep.

MINIB

IB is below IThrshld. Current for this phase is in creep.

MINIC

IC is below IThrshld. Current for this phase is in creep.

MINVA

VA is below VThrshld. Voltage for this phase is in creep.

MINVB

VB is below VThrshld. Voltage for this phase is in creep.

MINVC

VC is below VThrshld. Voltage for this phase is in creep.

CREEPV

All voltages are below VThrshld.

CREEP

There is no combination of current and voltage on any phase.

SOFTWARE

A software defect was detected. error_software() was called. E.g.: An impossible value oc-

curred in a selection, or the timers ran out.

NEUTRAL

Neutral current was above in_limit for more than in_wait seconds.

SPURIOUS

An unexpected interrupt was detected.

SAG

Voltage was below VThrshld for more than in_wait seconds

DEMAND

Demand was too big (too many watts) to be credible.

CALIBRATION

Set after reset if the read of the calibration data has a bad checksum, or is from an earlier ver-

sion of software. The default values should be present.

RTC_UNSET

Set when the clock’s current reading is A) Obtained after a cold start, indicating that there was

no battery power, and therefore the clock has to be invalid. B) More than a year after the previ-

ously saved reading, or C) Earlier than the previously saved reading. In this case, the clock’s

time is preserved, but the clock can’t be trusted.

HARDWARE

An impossible hardware condition was detected. For example, the woftware times out waiting

for RTC_RD to become zero.

BATTERY_BAD

Just after midnight, the demo code sets this bit if VBat < VBatMin. The read is infrequent to

reduce battery loading to very low values. When the battery voltage is being displayed, the

read occurs every second, for up to 20 seconds.

REGISTER_BAD

Set after reset when the read of the power register data has a bad longitudinal redundancy

check or bad software version in all 5 copies. Unlikely to be an accident.

RTC_TAMPER

Clock set to a new value more than two hours from the previous value.

TAMPER

Tamper was detected. Normally this is a power tamper detected in the creep logic. For exam-

ple, current detected with no voltage.

Table 1-9 contains LSB values for the CE registers. All values are based on the following settings:

• Gain in amplifier for IAP/IAN pins selected to 1.

• 71M6103, 71M6113, or 71M6203 Remote Sensor Interface is used.

Note that some of the register contents can be zeroed out by the MPU when it applies functions contained in its

creep logic.

71M6543 Demo Board User’s Manual

Page: 31 of 91 v5

1.10.4 LSB VALUES IN CE REGISTERS

Table 1-9: CE Registers and Associated LSB Values

W0SUM_X

W1SUM_X

W2SUM_X

1.55124*10-12*IMAX*VMAX The real energy for elements A, B, and C, measured in Wh per accu-

mulation interval

VAR0SUM_X

VAR1SUM_X

VAR2SUM_X

1.55124*10-12*IMAX*VMAX The reactive energy for elements A, B, and C, measured in VARh per

accumulation interval

I0SQSUM_X

I1SQSUM_X

I2SQSUM_X

INSQSUM_X

2.55872*10-12*IMAX*VMAX The sum of squared current samples in elements A, B, C, and neutral.

This value is the basis for the IRMS calculation performed in the MPU.

V0SQSUM_X

V1SQSUM_X

9.40448*10-13*IMAX*VMAX The sum of squared voltage samples in elements A, B, and C.

1.10.5 CALCULATING IMAX AND KH

The relationship between the resistance of the shunt resistors and the system variable IMAX is determined by

the type of Remote Sensor Interface used, and is as follows:

IMAX = 0.044194 / RS for the 71M6603

IMAX = 0.019642 / RS for the 71M61X1

IMAX = 0.012627 / RS for the 71M6203

Where:

RS = Shunt resistance in Ω

Table 1-10 shows IMAX values resulting from possible combinations of the shunt resistance value and the type

of 71M6x0x Remote Sensor Interface used for the application.

Table 1-10: IMAX for Various Shunt Resistance Values and Remote Sensor Types

Remote Sen-

sor Interface

Rated

Current

[A]

Max. RMS

Voltage at

IAP/IAN [mV]

Shunt Re-

sistor Value

[µΩ]

IMAX

[A]

IMAX En-

try at MPU

0x03

WRATE for kH =

3.2, VMAX = 600

V, X = 0.09375

71M6603 60 44.2

500

88.39

+884

3829

400

110.49

+1105

4786

300

147.31

+1473

6381

250

176.78

+1768

7657

200

220.97

+2209

9572

160

276.21

+2762

11965

120

368.28

+3683

15953

71M6103,

71M6113 100 19.64

250

78.57

786

3403

200

98.21

982

4254

160

122.76

1228

5318

120

163.68

1637

7090

100

196.42

1964

8508

71M6203,

71M6203 200 12.63

168.36

1684

7293

252.54

2525

10939

505.08

5050

21878

71M6543 Demo Board User’s Manual

Page: 32 of 91 v5

The meter constant kh (Wh per pulse) is calculated as follows:

Kh = 54.5793*VMAX*IMAX / (SUM_SAMPS*WRATE*X),

where

VMAX = RMS voltage at the meter input corresponding to 176.8 mV RMS at the VA pin of the

71M6543. This value is determines by the divider ratio of the voltage divider resistors. For the

71M6543 Demo Board, this value is 600.

IMAX/ = RMS current through one current sensor corresponding to the maximum RMS voltage at the

input pins of the 71M6103, as determined by the formula above.

SUM_SAMPS = The value in the SUM_SAMPS register in I/O RAM (2520 for this version of the Demo

Code).

WRATE = The value in the pulse rate adjustment register of the CE.

X = The pulse rate adjustment modifier, determined by the PULSE_FAST and PULSE_SLOW bits in

the CECONFIG register.

For the 71M6103, a kh of 3.2 (3.2 Wh per pulse) is achieved by the following combination of system settings:

VMAX = 600 V

IMAX/ = 163.7 A, based on RS = 120 μΩ

SUM_SAMPS = 2520

WRATE = 7090

X = 0.09375, based on PULSE_FAST =0 and PULSE_SLOW = 1

The calculations shown above are simplified if the calibration spreadsheet provided with each Demo Kit is used.

Figure 1-7 shows an example: The user enters data in the yellow fields, and the results will show in the green

fields.

Figure 1-7: Worksheet from Calibration Spreadsheets REV 6.0

1.10.6 DETERMINING THE TYPE OF 71M6X0X

Sometimes it is useful to be able to determine the type of 71M6x0x Remote Sensor Interface that is mounted on

the Demo Board. The CLI can be used to find out which Remote Sensor Interface is present, using the following

steps:

1) Type 6R1.14, 6R2.14, or 6R3.14, depending on which phase is tested.

2) The CLI will respond with a two-byte hex value, e.g. E9DB.

3) Write the hex value out as binary sequence, e.g. 1110 1001 1101 1011. Bits 4 and 5 determine the

type of the 71M6x0x Remote Sensor Interface, as shown in Table 1-11.

71M6543 Demo Board User’s Manual

Page: 33 of 91 v5

Table 1-11: Identification of 71M6x0x Remote Sensor Types

Bit 5/Bit 4 71M6x0x Remote Interface Current

[A]

For Accuracy Class (%)

00 71M6601 or 71M6603 60 1

01 71M6103 (Polyphase) or 100 1

71M6113 (Polyphase) 0.5

10 71M6201 or 71M6203 200 0.2

11 Invalid -- --

1.10.7 COMMUNICATING WITH THE 71M6X0X

Some commands are useful to communicate with the 71M6x0x Remote Sensor Interface for the purpose of test

and diagnosis. Some useful commands are:

1) 6C1.42 – this command causes the 71M6x0x Remote Sensor Interface to output its reference voltage

on the TMUX pin (pin 5).

2) 6R1.20 – this command returns the reading from the temperature sensor (STEMP) of the 71M6x0x

Remote Sensor Interface in a two-byte hexadecimal format (e.g. FFDF). Negative readings are sig-

naled by the MSB being 1.

T = 22°C + (STEMP*0.33 - (STEMP2)*0.00003)°C

Example: For STEMP = 0xFFDF the decimal equivalent is -32. The temperature calculates to 22°C –

10.59°C = 11.4°C.

Note that the IC temperature is averaged and displayed more accurately with the M1 command.

1.10.8 BOOTLOADER FEATURE

Demo Codes 5.4F and later are equipped with a bootloader feature. This feature allows the loading of code via

the serial interface (USB connector CN1) when a Signum ADM51 emulator or Maxim TFP2 Flash Loader is not

available.

The bootloader functions as follows:

1) Meter code must be modified in order to be loaded by the bootloader. The meter code must start at ad-

dress 0x0400, and its interrupt vector table must also start at 0x400. The bootloader itself is located at ad-

dress 0x0000 and must be loaded into the IC by some method if the flash memory of the 71M6543 is empty

or if code of a previous revision is loaded. The bootloader is part of Demo Code 5.4F.

2) The bootloader loads Intel hex-86 files at 38,400 baud 8 bits, no parity. It will only accept record types 0, 4

and 1, which are the types produced by Maxim’s Teridian bank_merge program or checksum program, and

the Keil compiler (PK51). No records may overlap. (Keil, bank_merge and checksum produce this style of

hex file by default.)

The records from 0x00000 to 0x00400 are ignored, so that the bootloader can't overwrite itself.

3) If the bootloader load process is not invoked, the bootloader jumps to address 0x0400 and executes the

code found there.

4) A detailed description of the bootloader can be found in the _readme.txt file contained in the source code

ZIP package (folder 6543_5p4f_14dec11\Config\Series6540\BtLd).

For a 71M6543 Demo Board containing code with the bootloader, instructions for loading new code are as fol-

lows:

1) Connect a PC running HyperTerminal or a similar terminal program to the 71M6543 Demo Board. Set the

program to 38,400 baud 8 bits, no parity, XON/XOFF flow control.

2) Turn off the power to the 71M6543 Demo Board.

3) Install a jumper from board ground to the VARh pulse output (JP7, right pin), which is also SEGDIO2. A low

voltage on this pin signals to the bootloader that new code should be loaded via the UART.

4) Apply power to the meter.

5) After a brief delay, the Wh pulse LED (D5) will light up (SEGDIO1). The bootloader should send a ":" on the

UART to the PC. If this occurs, the flash is erased, and the 71M6543 Demo Board is ready to load code.

- If this does not occur, check the jumper, and reset or repower the unit

- If the Wh LED still does not light up, then the boot code is not installed.

71M6543 Demo Board User’s Manual

Page: 34 of 91 v5

- If the Wh LED lights up, but the ":" does not appear, debug the RS-232 wiring. Possible issues are that the

baud rate is not 38400 baud, or that the wiring is wrong, (debug using a known-good meter), or that the

terminal program in the PC is not working.

6) Send the Intel hex file built for operation with the bootloader (e.g. 6543eq5_6103_5p4f_14dec11.hex) using

the ‘Send Text File’ command of HyperTerminal.

7) During the load procedure, the Wh LED will blink. Once the load process is completed it stops blinking.

The Wh LED should remain on solidly at the completion of the load procedure, which indicates an error-free

load. If the LED turns off at the end, an error must have occurred. In this case the load should be repeated.

The bootloader sends a "1" on the UART if the load succeeded, and "0" if it failed.

8) Check the display of terminal program (e.g. the PC running Hyperterminal). If no checksum error has oc-

curred, the bootloader sends a 1 on the UART. In case of an error, reset the 71M6543 Demo Board, or turn

it off and on, and reload the code.

9) Remove the jumper on JP7. This will cause the loaded Demo Code to start.

71M6543 Demo Board User’s Manual

Page: 35 of 91 v5

2 APPLICATION INFORMATION

2.1 CALIBRATION THEORY

A typical meter has phase and gain errors as shown by φS, AXI, and AXV in Figure 2-1. Following the typical me-

ter convention of current phase being in the lag direction, the small amount of phase lead in a typical current

sensor is represented as -φS. The errors shown in Figure 2-1 represent the sum of all gain and phase errors.

They include errors in voltage attenuators, current sensors, and in ADC gains. In other words, no errors are

made in the ‘input’ or ‘meter’ boxes.

INPUT

−φ

ERRORS

)

cos(

IDEAL

)

cos(

ACTUAL

−

≡

IDEAL

ACTUAL

IDEAL

ACTUAL

ERROR

RMS

METER

RMS

ACTUAL

IDEAL

ACTUAL

IDEAL

is phase lag

is phase lead

Figure 2-1: Watt Meter with Gain and Phase Errors.

During the calibration phase, we measure errors and then introduce correction factors to nullify their effect. With

three unknowns to determine, we must make at least three measurements. If we make more measurements, we

can average the results.

2.1.1 CALIBRATION WITH THREE MEASUREMENTS

The simplest calibration method is to make three measurements. Typically, a voltage measurement and two

Watt-hour (Wh) measurements are made. A voltage display can be obtained for test purposes via the command

>MR2.1 in the serial interface.

Let’s say the voltage measurement has the error EV and the two Wh measurements have errors E0 and E60,

where E0 is measured with φL = 0 and E60 is measured with φL = 60. These values should be simple ratios—not

percentage values. They should be zero when the meter is accurate and negative when the meter runs slow.

The fundamental frequency is f0. T is equal to 1/fS, where fS is the sample frequency (2560.62Hz). Set all cali-

bration factors to nominal: CAL_IA = 16384, CAL_VA = 16384, LCOMP2_A = 16384.

Note: The derivation of the calibration formulae is provided for CTs, where a phase adjustment is performed to

compensate for the phase error of the CT. For operation with 71M6xxx Remote Sensor Interfaces, a delay

compensation LCOMP2_n is used. Spreadsheets are available to calculate the calibration coefficients for all

hardware configurations.

71M6543 Demo Board User’s Manual

Page: 36 of 91 v5

From the voltage measurement, we determine that

1.

1+=

VXV

We use the other two measurements to determine φS and AXI.

1)cos(1

)0cos(

−=−

−

SXIXV

AAIV

2a.

)cos(

XIXV

)60cos(

−

=−

−

XIXV

SXIXV

AAIV

φφ

3a.

[ ]

)60cos(

)

sin()60sin()cos()60cos(

−

SSXIXV

φφ

1)sin()60tan()cos( −+=

SXIXVSXIXV

AAAA

φφ

Combining 2a and 3a:

)tan()60tan()1( 0060 S

EEE

++=

)60tan()1(

)tan(

060

−

6.













−

=−

)60tan()1(

tan

060

and from 2a:

7.

)cos(

SXV

XI A

Now that we know the AXV, AXI, and φS errors, we calculate the new calibration voltage gain coefficient from the

previous ones:

NEW

VCAL

VCAL _

We calculate PHADJ from φS, the desired phase lag:

[ ]













−−−−

−−−+

−−

)2cos()21(1)tan()2sin()21(

)2cos()21(2)21(1)tan(

929

TfTf

PHADJ

πφπ

πφ

And we calculate the new calibration current gain coefficient, including compensation for a slight gain increase

in the phase calibration circuit.

92020

)21()2cos()21(21

))2cos()21(222(2

−−

−−−

−+−−

−−+

TfPHADJPHADJ

ICAL

NEW

71M6543 Demo Board User’s Manual

Page: 37 of 91 v5

2.1.2 CALIBRATION WITH FIVE MEASUREMENTS

The five measurement method provides more orthogonality between the gain and phase error derivations. This

method involves measuring EV, E0, E180, E60, and E300. Again, set all calibration factors to nominal, i.e. CAL_IA

= 16384, CAL_VA = 16384, PHADJ_A = 0.

Note: The derivation of the calibration formulae is provided for CTs, where a phase adjustment is performed to

compensate for the phase error of the CT. For operation with 71M6xxx Remote Sensor Interfaces, a delay

compensation LCOMP2_n is used. Spreadsheets are available to calculate the calibration coefficients for all

hardware configurations.

First, calculate AXV from EV:

1.

1+= VXV EA

Calculate AXI from E0 and E180:

1)cos(1

)0cos(

−=−

−

SXIXV

AAIV

1)cos(1

)180cos(

180

−=−

−

SXIXV

AAIV

2)cos(2

1800

−=+

SXIXV

AAEE

)cos(2

1800

XIXV

6.

)cos(

12)(

1800

SXV

Use above results along with E60 and E300 to calculate φS.

)60cos(

−

=IV

AAIV

SXI

1)sin()60tan()cos( −+=

SXIXVSXIXV

AAAA

φφ

)60cos(

300

−

−−

=IV

AAIV

SXIXV

1)sin()60tan()cos( −−= SXIXVSXIXV AAAA

φφ

Subtract 8 from 7

)sin()60tan(2

30060 SXIXV

AAEE

=−

use equation 5:

10.

)sin()60tan(

)cos(

1800

30060 S

=−

11.

)tan(

)60tan()2(

180030060 S

EEEE

++=−

12.













−

=−

)2)(60tan(

)(

tan

1800

30060

71M6543 Demo Board User’s Manual

Page: 38 of 91 v5

Now that we know the AXV, AXI, and φS errors, we calculate the new calibration voltage gain coefficient from the

previous ones:

NEW

VCAL

VCAL _

We calculate PHADJ from φS, the desired phase lag:

[ ]













−−−−

−−−+

−−

)2cos()21(1)tan()2sin()21(

)2cos()21(2)21(1)tan(

929

TfTf

PHADJ

πφπ

πφ

And we calculate the new calibration current gain coefficient, including compensation for a slight gain increase

in the phase calibration circuit.

92020

)21()2cos()21(21

))2cos()21(222(2

−−

−−−

−+−−

−−+

TfPHADJPHADJ

ICAL

NEW

2.2 CALIBRATION PROCEDURES

2.2.1 CALIBRATION EQUIPMENT

Calibration requires that a calibration system is used, i.e. equipment that applies accurate voltage, load current

and load angle to the unit being calibrated, while measuring the response from the unit being calibrated in a re-

peatable way. By repeatable we mean that the calibration system is synchronized to the meter being calibrated.

Best results are achieved when the first pulse from the meter opens the measurement window of the calibration

system. This mode of operation is opposed to a calibrator that opens the measurement window at random time

and that therefore may or may not catch certain pulses emitted by the meter.

It is essential for a valid meter calibration to have the voltage stabilized a few seconds be-

fore the current is applied. This enables the Demo Code to initialize the 71M6543F and to

stabilize the PLLs and filters in the CE. This method of operation is consistent with meter

applications in the field as well as with metering standards.

During calibration of any phase, a stable mains voltage has to be present on phase A. This

enables the CE processing mechanism of the 71M6543F necessary to obtain a stable cali-

bration.

2.2.2 DETAILED CALIBRATION PROCEDURES

The procedures below show how to calibrate a meter phase with either three or five measurements. The

PHADJ equations apply only when a current transformer is used for the phase in question. Note that positive

load angles correspond to lagging current (see Figure 2-2).

71M6543 Demo Board User’s Manual

Page: 39 of 91 v5

Figure 2-2: Phase Angle Definitions

The calibration procedures described below should be followed after interfacing the voltage and current sensors

to the 71M6543F chip. When properly interfaced, the V3P3 power supply is connected to the meter neutral and

is the DC reference for each input. Each voltage and current waveform, as seen by the 71M6543F, is scaled to

be less than 250mV (peak).

2.2.3 CALIBRATION PROCEDURE WITH THREE MEASUREMENTS

Each phase is calibrated individually. The calibration procedure is as follows:

1) The calibration factors for all phases are reset to their default values, i.e. CAL_In = CAL_Vn = 16384,

and LCOMP2_n = 16384.

2) An RMS voltage Videal consistent with the meter’s nominal voltage is applied, and the RMS reading

Vactual of the meter is recorded. The voltage reading error Axv is determined as

Axv = (Vactual - Videal ) / Videal

3) Apply the nominal load current at phase angles 0° and 60°, measure the Wh energy and record the er-

rors E0 AND E60.

4) Calculate the new calibration factors CAL_In, CAL_Vn, and LCOMP2_n, using the formulae present-

ed in section 2.1.1 or using the spreadsheet presented in section 2.2.5.

5) Apply the new calibration factors CAL_In, CAL_Vn, and LCOMP2_n to the meter. The memory loca-

tions for these factors are given in section 1.9.1.

6) Test the meter at nominal current and, if desired, at lower and higher currents and various phase an-

gles to confirm the desired accuracy.

7) Store the new calibration factors CAL_In, CAL_Vn, and LCOMP2_n in the EEPROM or FLASH

memory of the meter. If the calibration is performed on a Teridian Demo Board, the methods involving

the command line interface, as shown in sections 1.9.3 and 1.9.4, can be used.

8) Repeat the steps 1 through 7 for each phase.

Tip: Step 2 and the energy measurement at 0° of step 3 can be combined into one step.

Voltage

Current

+60°

Using EnergyGenerating Energy

Current lags

voltage

(inductive

)

Current leads

voltage

(capacitive

)

-60°

Voltage

Positive

direction

71M6543 Demo Board User’s Manual

Page: 40 of 91 v5

2.2.4 CALIBRATION PROCEDURE WITH FIVE MEASUREMENTS

Each phase is calibrated individually. The calibration procedure is as follows:

1) The calibration factors for all phases are reset to their default values, i.e. CAL_In = CAL_Vn = 16384,

and LCOMP2_n = 0.

2) An RMS voltage Videal consistent with the meter’s nominal voltage is applied, and the RMS reading

Vactual of the meter is recorded. The voltage reading error Axv is determined as

Axv = (Vactual - Videal ) / Videal

3) Apply the nominal load current at phase angles 0°, 60°, 180° and –60° (-300°). Measure the Wh ener-

gy each time and record the errors E0, E60, E180, and E300.

4) Calculate the new calibration factors CAL_In, CAL_Vn, and LCOMP2_n, using the formulae present-

ed in section 2.1.2 or using the spreadsheet presented in section 2.2.5.

5) Apply the new calibration factors CAL_In, CAL_Vn, and LCOMP2_n to the meter. The memory loca-

tions for these factors are given in section 1.9.1.

6) Test the meter at nominal current and, if desired, at lower and higher currents and various phase an-

gles to confirm the desired accuracy.

7) Store the new calibration factors CAL_In, CAL_Vn, and LCOMP2_n in the EEPROM or FLASH

memory of the meter. If a Demo Board is calibrated, the methods involving the command line interface

shown in sections 1.9.3 and 1.9.4 can be used.

8) Repeat the steps 1 through 7 for each phase.

Tip: Step 2 and the energy measurement at 0° of step 3 can be combined into one step.

2.2.5 CALIBRATION SPREADSHEETS

Calibration spreadsheets are available on the Maxim web site (www.maxim-ic.com). Figure 2-3 shows the

spreadsheet for three measurements. Figure 2-4 shows the spreadsheet for five measurements with three

phases.

Use the standard calibration spreadsheets (for 71M651x, 71M652x, or 71M653x) when calibrating meters with

CTs. These spreadsheets will provide results for the PHADJ_n parameters instead of the LCOMP2_n parame-

ters.

For the calibration, data should be entered into the calibration spreadsheets as follows:

1. Calibration is performed one phase at a time.

2. Results from measurements are generally entered in the yellow fields. Intermediate results and calibra-

tion factors will show in the green fields.

3. The line frequency used (50 or 60Hz) is entered in the yellow field labeled AC frequency.

4. After the voltage measurement, measured (observed) and expected (actually applied) voltages are en-

tered in the yellow fields labeled “Expected Voltage” and “Measured Voltage”. The error for the voltage

measurement will then show in the green field above the two voltage entries.

5. The relative error from the energy measurements at 0° and 60° are entered in the yellow fields labeled

“Energy reading at 0°” and “Energy reading at 60°”. The corresponding error, expressed as a fraction

will then show in the two green fields to the right of the energy reading fields.

6. The spreadsheet will calculate the calibration factors CAL_IA, CAL_VA, and LCOMP2_A from the in-

formation entered so far and display them in the green fields in the column underneath the label “new”.

7. If the calibration was performed on a meter with non-default calibration factors, these factors can be

entered in the yellow fields in the column underneath the label “old”. For a meter with default calibra-

tion factors, the entries in the column underneath “old” should be at the default value (16384).

71M6543 Demo Board User’s Manual

Page: 41 of 91 v5

Figure 2-3: Calibration Spreadsheet for Three Measurements

Note: The values for LCOMP2_n may have to be changed slightly depending on shunt sensor and cable in-

ductance. The values from the spreadsheets provide starting points. For example, if after calibration the error

or 0° load angle is 0.024%, but +1.25% at 60° and -1.18% at 300°, LCOMP2_n should be increased to mini-

mize the errors at 60° and at 300°.

71M6543 Demo Board User’s Manual

Page: 42 of 91 v5

Figure 2-4: Calibration Spreadsheet for Five Measurements

Note: The spreadsheets shown above apply to calibration for systems with 71M6xxx Remote Sensor Interfaces.

For CT-bases meters, the regular spreadsheets (also used for the 71M6513, 71M6533, and 71M6534) should

be used.

2.2.6 COMPENSATING FOR NON-LINEARITIES

Nonlinearity is most noticeable at low currents, as shown in Figure 2-5, and can result from input noise and

truncation. Nonlinearities can be eliminated using the QUANTA, QUANTB,and QUANTC variables.

Figure 2-5: Non-Linearity Caused by Quantification Noise

The error can be seen as the presence of a virtual constant noise current. While 10mA hardly contribute any er-

ror at currents of 10A and above, the noise becomes dominant at small currents.

0.1 110 100

I [A]

error [%]

error

71M6543 Demo Board User’s Manual

Page: 43 of 91 v5

The value to be used for QUANT can be determined by the following formula:

LSBIMAXVMAX

error

QUANT ⋅⋅

⋅

−= 100

Where error = observed error at a given voltage (V) and current (I),

VMAX = voltage scaling factor, as described in section 1.8.3,

IMAX = current scaling factor, as described in section 1.8.3,

LSB = QUANT LSB value = 7.4162*10-10W

Example: Assuming an observed error as in Figure 2-5, we determine the error at 1A to be +1%. If VMAX is

600V and IMAX = 208A, and if the measurement was taken at 240V, we determine QUANTn as follows:

11339

104162.7208600

1240

100

10 −=

⋅⋅⋅

⋅

−= −

QUANT

There is a QUANTn register for each phase, and the values are to be written to the CE locations 0x28, 0x2C, or

0x30. It does not matter which current value is chosen as long as the corresponding error value is significant

(5% error at 0.2A used in the above equation will produce the same result for QUANTn).

Input noise and truncation can cause similar errors in the VAR calculation that can be eliminated using the

QUANT_VARn variables. QUANT_VARn is determined using the same formula as QUANT.

2.3 TEMPERATURE COMPENSATION

2.3.1 ERROR SOURCES

This section discussed the temperature compensation for meters equipped with 71M6xxx Remote Sensor Inter-

faces. Compensation for CT-based systems is much simpler, since the error sources are only the reference

voltage, the burden resistor, and the voltage dividers.

For a meter to be accurate over temperature, the following major sources of error have to be addressed:

1) The resistance of the shunt sensor(s) over temperature. The temperature coefficient (TC) of a shunt

resistor is typically positive (PTC) and can be far higher than the TC of the pure Manganin material

used in the shunt. TCs of several hundred PPM/°C have been observed for certain shunt resistors. A

shunt resistor with +100 PPM/°C will increase its resistance by 60°C * 100*10-6 PPM/°C, or +0.6%

when heated up from room temperature to +85°C, causing a relative error of +0.6% in the current

reading. This makes the shunt the most pronounced influence on the temperature characteristics of

the meter.

Typically, the TC of shunt resistors is mostly linear over the industrial temperature range and can be

compensated, granted the shunt resistor is at the same temperature as the on-chip temperature sen-

sors on the 71M6x0x Remote Sensor Interface IC or the 71M6543.

Generally, the lower the TC of a shunt resistor, the better it can be compensated. Shunts with high

TCs require more accurate temperature measurements than those with low TCs. For example, if a

shunt with 200 PPM/°C is used, and the temperature sensor available to the 71M6543 is only accurate

to ±3°C, the compensation can be inaccurate by as much as 3°C*200PPM/°C = 600 PPM, or 0.06%.

2) The reference voltage of the 71M6x03 Remote Sensor Interface IC. At the temperature extremes, this

voltage can deviate by a few mV from the room temperature voltage and can therefore contribute to

some temperature-related error. The TC of the reference voltage has both linear and quadratic com-

ponents (TC1 and TC2). Since the 71M6X03 Remote Interface IC has an on-chip temperature sensor,

and since the development of the reference voltage over temperature is predictable (to within ±10

PPM/°C for high-grade parts). For example, compensation of the current reading is possible for a part

with ±80 PPM°C to within ±60°C *80*10-6 PPM/°C, or ±0.48%.

The reference voltage can be approached by the nominal reference voltage:

VNOM(T) = VNOM(22)+(T-22)*TC1+(T-22)2*TC2

Actual values for TC1 and TC2 can be obtained using the formulae given in the data sheets for the

71M6543 and for the 71M6x03. Additionally, the Demo Code will automatically generate the compen-

sation coefficients based on TC1 and TC2 using the fuse values in each device.

71M6543 Demo Board User’s Manual

Page: 44 of 91 v5

3) The reference voltage of the 71M6543F IC. At the temperature extremes, this voltage can deviate by a

few mV from the room temperature voltage and can therefore contribute to some temperature-related

error, both for the current measurement (pins IAP and IAN) of the neutral current sensor (if used) and

for the voltage measurement (pin VA). As with the Remote Sensor Interface IC, the TC of the

71M6543F reference voltage has both linear and quadratic components. The reference voltage of the

71M6543F over temperature is predictable within ±40 PPM/°C, which means that compensation of the

current and voltage reading is possible to within ±0.24%.

The 71M6543H has more predictable temperature coefficients that allow compensation to within ±10

PPM/°C, resulting in ±0.06% inaccuracy.

The temperature coefficients of the reference voltage are published in the 71M6543F/H data sheet.

The Demo Code will automatically generate the compensation coefficients based on TC1 and TC2 us-

ing the fuse values in each device.

4) The voltage divider network (resistor ladder) on the Demo Board will also have a TC. Ideally, all resis-

tors of this network are of the same type so that temperature deviations are balanced out. However,

even in the best circumstances, there will be a residual TC from these components.

The error sources for a meter are summed up in Table 2-1.

Table 2-1: Temperature-Related Error Sources

Measured Item

Error Sources for Current

Error Sources for Voltage

Pins on 71M6543

Energy Reading

for phase A

VREF of 71M6xx3 for phase A 71M6543 VREF VA, ADC2/ADC3

(IBP/IBN)

Shunt resistor for phase A Voltage divider for VA

Energy Reading

for phase B

VREF of 71M6xx3 for phase B 71M6543 VREF VB, ADC4/ADC5)

ICP/ICN

Shunt resistor for phase B Voltage divider for VB

Energy Reading

for phase C

VREF of 71M6xx3 for phase C 71M6543 VREF VC, ADC6/ADC7

(IDP/IDN)

Shunt resistor for phase C Voltage divider for VC

Neutral Current

Reading

71M6543 VREF -- ADC0/ADC1

(IAP/IAN)

Sensor for neutral current --

When can summarize the thermal errors per phase n in the following equation:

( ) ( ) ( ) ( )

XSnXVDnnn CCCCIVP 64 1111 +⋅+⋅+⋅+⋅⋅=

The terms used in the above equation are defined as follows:

• Vn = voltage applied to the meter in phase n

• In = current applied to the shunt in phase n

• CVD = error contribution from the voltage divider

• C4X = error contribution from the voltage reference of the 71M6543

• CSn = error from the shunt resistor that is connected via the Remote Interface IC

• C6X = error contribution from the voltage reference of the Remote Interface IC

2.3.2 SOFTWARE FEATURES FOR TEMPERATURE COMPENSATION

In the default settings for the Demo Code, the CECONFIG register has its EXT_TEMP bit (bit 22) set, which

means that temperature compensation is performed by the MPU by controlling the GAIN_ADJ0 through

GAIN_ADJ, registers of the CE. Generally, these four (and when using neutral current measurement, five) reg-

isters are used as follows:

• GAIN_ADJ0 for VA, VB, VC – CE RAM 0x40

• GAIN_ADJ1 – Current, phase A (via 71M6xx3) – CE RAM 0x41

• GAIN_ADJ2 - Current, phase B (via 71M6xx3) – CE RAM 0x42

• GAIN_ADJ3 - Current, phase C (via 71M6xx3) – CE RAM 0x43

• GAIN_ADJ4 – Current from neutral current sensor (via 71M6543) – CE RAM 0x44

In general, the GAIN_ADJn registers offer a way of controlling the magnitude of the voltage and current signals

in the data flow of the CE code. A value of 16385 means that no adjustment is performed (unity gain), which

71M6543 Demo Board User’s Manual

Page: 45 of 91 v5

means that the output of the gain adjust function is the same as the input. A value of 99% of 16385, or 16222,

means that the signal is attenuated by 1%.

The Demo Code bases its adjustment on the deviation from calibration (room) temperature DELTA_T and the

coefficients PPMC and PPMC2 to implement the equation below:

14 2

16385_ PPMCTDELTAPPMCTDELTA

ADJGAIN ⋅

⋅

It can be seen easily that the gain will remain at 16385 (0x4001), or unity gain, when DELTA_T is zero. In the

Demo Code, DELTA_T is scaled so 0.1°C corresponds to 1 LSB of DELTA_T.

For complete compensation, the error sources for each channel have to be combined and curve-fit to generate

the PPMC and PPMC2 coefficients, as will be shown in the following section.

For Demo Codes revision 5.3a and later, the PPMC and PPMC2 coefficients are in the MPU RAM locations

listed in Table 2-3:

Table 2-2: MPU Registers for Temperature-Compensation

CE Lo-

cation

PPMC Register for CE Lo-

cation

PPMC2 Register for

0x20 GAIN_ADJ0 0x25 GAIN_ADJ0

0x21 GAIN_ADJ1 0x26 GAIN_ADJ1

0x22 GAIN_ADJ2 0x27 GAIN_ADJ2

0x23 GAIN_ADJ3 0x28 GAIN_ADJ3

0x24 GAIN_ADJ0 0x29 GAIN_ADJ0

When the Demo Code starts up (after reset or power-up), it determines whether the meter has been calibrated.

If this is not the case, the coefficients PPMC and PPMC2 are automatically determined based on information

found in the 71M6543 and in the 71M6x0x Remote Sensor Interface ICs. These coefficients are calculated to

compensate for the reference voltage deviation in these devices, but can be enhanced to also compensate for

the shunt resistors connected to each device.

2.3.3 CALCULATING PARAMETERS FOR COMPENSATION

2.3.3.1 Shunt Resistors

The TC of the shunt resistors can be characterized using a temperature chamber, a calibrated current, and a

voltmeter with filtering capabilities. A few shunt resistors should be measured and their TC should be compared.

This type of information can also be obtained from the manufacturer. For sufficient compensation, the TC of the

shunt resistors must be repeatable. If the shunts are the only temperature-dependent components in a meter,

and the accuracy is required to be within 0.5% over the industrial temperature range, the repeatability must be

better than:

R = (5000 PPM) / (60°C) = 83.3 PPM/°C

This means that for a shunt resistor with +200 PPM/°C, the individual samples must be within +116.7 PPM/°C

and 283.3 PPM/°C.

Let us assume a shunt resistor of 55 µΩ in phase A. This resistor is 10% above the nominal value of 50 µΩ, but

this is of minor importance, since this deviation will be compensated by calibration. In a temperature chamber,

this resistor generates a voltage drop of 5.4559 mV at -40°C and 5.541 mV at +85°C with a current of 100 A

applied. This is equivalent to a resistance deviation of 0.851 µΩ, or 15,473 PPM. With a temperature difference

between hottest and coldest measurement of 125°C, this results in +124 PPM/°C. At high temperatures, this re-

sistor will read the current 60°C * 124 PPM/°C, or 0.744% too high. This means that the GAIN_ADJ1 register

has to be adjusted by -0.744% at the same temperature to compensate for the TC of the shunt resistor.

71M6543 Demo Board User’s Manual

Page: 46 of 91 v5

Let us assume that only linear components appear in the formula below, i.e. PPMC2 is zero.

14 2

16385_ PPMCTDELTAPPMCTDELTA

ADJGAIN ⋅

⋅

We must now find the PPMC value that decreases GAIN_ADJ by 0.744% when DELTA_T is +600 (DELTA_T

is measured in tens of °C). We find PPMCS to be:

PPMCS = 214 * (16263 – 16385) / 600 = -3331

2.3.3.2 Remote Sensor Reference Voltage

The compensation coefficients for the reference voltage of the three 71M6103 are derived automatically by the

Demo Code. Typical coefficients are in the range of +500 to -300 for PPMC6X and -200 to -400 for PPMC26X.

2.3.3.3 Reference Voltage of the 71M6543 or 71M6543H

The compensation coefficients for the reference voltage of the 71M6543 are derived automatically by the Demo

Code. Typical coefficients are in the range of -200 to -400 for PPMC4X and -400 to -800 for PPMC24X.

2.3.3.4 Voltage Divider

In most cases, especially when identical resistor types are used for all resistors of the voltage divider ladder, the

TC of the voltage divider will be of minor influence on the TC of the meter.

If desired, the voltage divider can be characterized similar to the shunt resistor as shown above. The difference

is that there is no individual GAIN_ADJ for each voltage channel. GAIN_ADJ0 is primarily intended to compen-

sate for the temperature coefficients of the reference voltage. If the TC of the voltage dividers is to be consid-

ered, it has to be calculated based on the average error of each phase.

Let us assume, applying 240 Vrms to a meter and recording the RMS voltage displayed by the meter at -40°C,

room temperature, +55°C, and at +85°C (when averaged over all phases), we obtain the values in the center

column of Table 2-3.

Table 2-3: Temperature-Related Error Sources

Temperature [°C] Displayed Voltage Normalized Voltage

-40 246.48 240.458

25 246.01 240.0

55 245.78 239.78

85 245.56 239.57

After normalizing with the factor 240/246.01 to accommodate for the initial error, we obtain the values in the

third column. We determine the voltage deviation between highest and lowest temperature to be -0.88 V, which

is equivalent to -3671 PPM, or -29.4 PPM/°C.

For this, we obtain a PPMCVD value of 788.

2.3.3.5 Combining the Coefficients for Temperature Compensation

After characterizing all major contributors to the TC of the meter, we have all components at hand to design the

overall compensation. If we examine only phase A for the moment, we find that we will need the following coef-

ficients for the control of GAIN_ADJn:

CS1: The PPMCS = -3331 determined for the shunt resistor. PPMC2S for the shunt resistor is 0.

CVD: The PPMCVD value of 788 determined for the voltage divider.

C4X: PPMC4X = -820 and PPMC24X = -680

C6X: PPMC6X = -620 and PPMC26X = -510

We will find that coefficients can simply be added to combine the effects from several sources of temperature

dependence.

Following this procedure, we obtain the coefficients for GAIN_ADJ0 (voltage measurement) as follows:

• PPMCA = PPMC4X + PPMCVD = – 820 + 788 = -32

• PPMC2A = PPMC24X + PPMC2VD = -680 + 0 = -680

71M6543 Demo Board User’s Manual

Page: 47 of 91 v5

Next, we obtain the coefficients for GAIN_ADJ1 (current measurement) as follows:

• PPMCA = PPMCS + PPMC6X = -3331 - 620 = -3951

• PPMC2A = PPMC2S + PPMC26X = 0 - 510 = -510

Similar calculations apply to the remaining current phases.

2.3.3.6 Test Results for Temperature Compensation

Temperature tests were conducted that exercised the fuse accuracy in the 71M6xxx and 71M6543 in conjunc-

tion with the capability of the 654x Code to accurately read and interpret the fuses and to compensate the gain

in all measurement channels.

For these tests, three 50 µΩ shunts had been characterized, and coefficients combined from the shunt coeffi-

cients and the VREF coefficients for the 71M6543H and 71M6xxx had been generated and loaded into the

71M6543H. No compensation was used for the voltage divider in the 71M6543 Demo Board. The tests were

conducted with a 71M6543 Demo Board REV 3.0 populated with a 71M6543H and 3 x 71M6203 (dual-trim).

Figure 2-6 shows the results for the VREF compensation only (original coefficients obtained from fuses).

Figure 2-6: Wh Registration Error with VREF Compensation

Figure 2-7 shows the results for the combined compensation (original coefficients obtained from fuses com-

bined with shunt coefficients).

71M6543 Demo Board User’s Manual

Page: 48 of 91 v5

Figure 2-7: Wh Registration Error with Combined Compensation

2.4 TESTING THE DEMO BOARD

This section will explain how the 71M6543F IC and the peripherals can be tested. Hints given in this section will

help evaluating the features of the Demo Board and understanding the IC and its peripherals.

Demo Board. It interfaces to a PC through a 9 pin serial port connector.

It is recommended to set up the demo board with no live AC voltage connected, and to

connect live AC voltages only after the user is familiar with the demo system.

BEFORE CONNECTING THE DEMO BOARD TO A CALIBRATION SYSTEM OR OTHER

HIGH-VOLTAGE SOURCE IT IS RECOMMENDED TO MEASURE THE RESISTANCE BE-

TWEEN THE LINE AND THE NEUTRAL TERMINALS OF THE DEMO BOARD WITH A MULTI-

METER. ANY RESISTANCE BELOW THE 1 MΩ RANGE INDICATES A AFAULTY CONNEC-

TION RESULTING INDESTRUCTION OF THE 71M6543.

2.4.1 FUNCTIONAL METER TEST

This is the test that every Demo Board has to pass before being integrated into a Demo Kit. Before going into

the functional meter test, the Demo Board has already passed a series of bench-top tests, but the functional

meter test is the first test that applies realistic high voltages (and current signals from current transformers) to

the Demo Board.

Figure 2-8 shows a meter connected to a typical calibration system. The calibrator supplies calibrated voltage

and current signals to the meter. It should be noted that the current flows through the shunts or CTs that are not

part of the Demo Board. The Demo Board rather receives the voltage output signals from the current sensor. An

optical pickup senses the pulses emitted by the meter and reports them to the calibrator. Some calibration sys-

tems have electrical pickups. The calibrator measures the time between the pulses and compares it to the ex-

pected time, based on the meter Kh and the applied power.

71M6543 Demo Board User’s Manual

Page: 49 of 91 v5

Figure 2-8: Meter with Calibration System

Figure 2-9 shows the screen on the controlling PC for a typical Demo Board. The error numbers are given in

percent. This means that for the measured Demo Board, the sum of all errors resulting from tolerances of PCB

components, current sensors, and 71M6543F tolerances was –3.41%, a range that can easily be compensated

by calibration.

Figure 2-10 shows a load-line obtained with a 71M6543F. As can be seen, dynamic ranges of 200:0.25, or

1:800 for current can easily be achieved. Dynamic current ranges of 2,000:1 (0.1 A to 200 A) have been

achieved with 50 µΩ shunts mounted in ANSI enclosures.

Figure 2-9: Calibration System Screen

Calibrator

AC Voltage

Current CT

Meter

under

Test Optical Pickup

for Pulses

Calibrated

Outputs

Pulse

Counter

71M6543 Demo Board User’s Manual

Page: 50 of 91 v5

Figure 2-10: Wh Load Lines at Room Temperature with 150 µΩ Shunts

Figure 2-11: VARh Load Lines at Room Temperature with 150 µΩ Shunts

2.4.2 EMC TEST

This Demo Board is not optimized for EMC. Please contact your Maxim representative or FAE for questions re-

garding EMC.

2.5 SENSORS AND SENSOR PLACEMENT

Both sensor self-heating and sensor placement have to be considered in order to avoid side effects that can af-

fect measurement accuracy. These considerations apply in general to both ANSI meters and IEC meters.

Both meter variations will be discussed below.

-0.5

-0.4

-0.3

-0.2

-0.1

0.1

0.2

0.3

0.4

0.5

0.1 110 100

0°

60°

Wh Poly-Phase Loadline with 150 µΩShunt

-0.5

-0.4

-0.3

-0.2

-0.1

0.1

0.2

0.3

0.4

0.5

0.1 110 100

90°

150°

VARh Poly-Phase Loadline with 150 µΩShunt

71M6543 Demo Board User’s Manual

Page: 51 of 91 v5

2.5.1 SELF-HEATING

The effect of self-heating will be most pronounced at maximum current and depends on the following parame-

ters:

• Nominal shunt resistance

• Current through the shunt resistor

• Thermal mass

• Heat conduction away from the shunt (thermal resistance towards the environment)

• Temperature coefficient of copper and resistive material.

It is quite obvious that the nominal resistance of the shunt resistor should be kept as low as possible. Table

1-10 shows a few combinations of shunt resistance and 71M6x0x part number. The parts with part numbers

corresponding to higher current capacity are designed to work with low shunt resistance. Lowering the shunt re-

sistance below the recommended limits decreases accuracy and repeatability.

Good heat conduction can help to maintain the shunt temperature. Attaching the shunt to solid metallic struc-

tures such as meter terminal blocks helps decreasing the thermal resistance. This, of course, applies to meters

where the terminals and other mechanical parts can be considered heat sinks, i.e. they do not heat up due to

other effects.

The thermal mass will control how long it takes the sensor to reach its maximum temperature. Meters, for which

only short-time maximum currents are applied, can benefit from a large thermal mass, since it will increase the

time constant of the temperature rise.

The temperature coefficient (TC) of the shunt is a very important factor for the self-heating effect. Shunts with a

TC of just a few PPM/°C can maintain good shunt accuracy even in the presence of significant self-heating.

There are several methods that can be applied in the meter design to minimize the effects of self-heating:

• Software algorithms emulating the thermal behavior of the shunt(s).

• Direct temperature measurement, ideally with the 71M6xx3 mounted directly on the shunt (collocation)

or employing some other method of temperature sensing (PTC resistor, NTC resistor, discrete temper-

ature sensor).

The effect of shunt self-heating can be described by the following formulae. First, the relative output of a shunt

resistor is:

ΔV/V = ΔR/R

ΔR is a function of the change in temperature, the temperature coefficient (TCR), the thermal resistance (RTH),

and, of course, the applied power, which is proportional to the square of the current:

RTH

TCRRI

TCTR

V⋅⋅=

⋅∆⋅

∆

Ultimately, it is up to the meter designer to select the best combination of shunt resistance, TC, shunt geometry

and potential software algorithms for the given application.

2.5.2 PLACEMENT OF SENSORS (ANSI)

The arrangement of the current terminals in an ANSI meter enclosure predetermines shunt orientation, but it al-

so allows for ample space in between the sensors, which helps to minimize cross-talk between phases.

A good practice is to shape the shunts like blades and to place them upright so their surfaces are parallel. In an

ANSI-type 16S meter, the distance between the phase A sensor and the phase B sensor is roughly 25 mm,

which makes these two phases most critical for cross-talk. For the ANSI form 2S meter, which is a frequently

used single-phase configuration, the distance between the sensors is in the range of 70 mm, which makes this

configuration much less critical. However, even for this case, good sensor placement is essential to avoid cross-

talk.

Sensor wires should be tightly twisted to avoid loops that can be penetrated by the magnetic fields of the sen-

sors or conductors.

2.5.3 PLACEMENT OF SENSORS (IEC)

The arrangement of the current terminals in a typical IEC meter enclosure predetermines the spacing of the

shunts, and usually allows for only for 20 to 22 mm center-to-center spacing between the shunts. This means

that the clearance between adjacent shunts is typically only 10 mm or less. A typical arrangement is shown in

71M6543 Demo Board User’s Manual

Page: 52 of 91 v5

Figure 2-12, left side. This arrangement is not optimized for suppression of cross-talk, but it works well in most

cases.

If magnetic cross-talk between shunt sensors has to be minimized, the shunts may be arranged slightly different

from the standard configuration. An example with staggered shunt arrangement is shown in Figure 2-12, right

side. This illustration shows the shunts as seen from inside the meter, looking towards the terminal blocks. The

center shunt is lifted on spacers, which decouples the magnetic field lines.

Figure 2-12: Typical Sensor Arrangement (left), Alternative Arrangement (right)

Another possible arrangement is to swivel the shunts by 90°, as shown in Figure 2-13. This method is most ef-

fective at suppressing magnetic cross-talk, but requires more space in the meter enclosure.

Figure 2-13: Swiveled Sensor Arrangement

It is useful to minimize the loop area formed by the Manganin zone of the shunts and the wires. As with the AN-

SI sensors, it is recommended that sensor wires are tightly twisted to avoid loops that can be penetrated by the

magnetic fields of the sensors or conductors.

2.5.4 OTHER TECHNIQUES FOR AVOIDING MAGNETIC CROSSTALK

With very high currents or close distances between shunt sensors, magnetic pickup or cross-talk will sometimes

occur even if good placement practices are followed.

One mechanism for cross-talk is shown in Figure 2-14, where the Manganin zone and the sensor wire act as a

loop that will generate an output voltage similar to that generated by a Rogowski coil.

The effect of this loop can be compensated by adding a second loop on the opposite side of the shunt resistors,

as shown in Figure 2-15.

71M6543 Demo Board User’s Manual

Page: 53 of 91 v5

Figure 2-14: Loop Formed by Shunt and Sensor Wire

Figure 2-15: Shunt with Compensation Loop

Since the compensation loop is impractical, a similar compensation effect can be achieved by attaching the

sensor wires in the center, as shown in Figure 2-16. An economical approach to this technique is to drill holes in

the center of the shunt resistor for attachment of the sensor wires 1.

Figure 2-16: Shunt with Center Drill Holes

1 U.S. Pat. Pending

Loop Manganin

Copper

Sensor wires

Optional contact for

voltage

Symmetrical

loops

71M6543 Demo Board User’s Manual

Page: 54 of 91 v5

71M6543 Demo Board User’s Manual

Page: 55 of 91 v5

3 HARDWARE DESCRIPTION

3.1 71M6543 REV 4.0 DEMO BOARD DESCRIPTION: JUMPERS,

SWITCHES AND TEST POINTS

The items described in Table 3-1 refer to the flags in Figure 3-1.

Table 3-1: 71M6543 REV 4.0 Demo Board Description

Item # Reference

Designator Name Use

1 D5 Wh Wh pulse LED.

2 J1 PULSE X Y 3-pin header for monitoring X and Y pulses

3 JP2 BIT BANG 5-pin header for access to the SEGDIO4 and SEGDIO9

pins.

4 JP1 BAT MODE

Selector for the operation of the IC when main power is re-

moved, using the SEGDIO8 pin. A jumper across pins 2-3

(default) indicates that no external battery is available. The

IC will stay in brownout mode when the system power is

down and it will communicate at 9600bd. A jumper across

pins 1-2 indicates that an external battery is available. The

IC will be able to transition from brownout mode to sleep

and LCD modes when the system power is down.

5 JP55/JP52 --

JP55: 2-pin header for the SDATA signal used by the serial

EEPROM.

JP52: 2-pin header for the SDATA signal used by the

µWire EEPROM

6 U8 LCD 3-row LCD with 6 7-segment digits per row and special

metering symbols.

7 J19 SPI 2X5 header providing access to the SPI slave interface.

8 BT3 -- Alternate footprint for BT2. A circular battery may be

mounted in this location (on the bottom of the board).

9 BT1 -- Location of optional battery for the support of battery

modes. (Located on the bottom)

71M6543 Demo Board User’s Manual

Page: 56 of 91 v5

Item # Reference

Designator Name Use

10 BT2 --

Location of optional battery for the support of RTC and

non-volatile RAM. BT2 has an alternate circular footprint at

location BT3.

11 J21 DEBUG Connector for the optional Debug Board. 2x8 pin male

header.

12 SW5 RESET

Chip reset switch: When the switch is pressed, the RESET

pin of the IC is pulled high which resets the IC into a known

state.

13 J12 -- 2-pin header. If a jumper installed, the battery BT1 will be

connected to the V3P3SYS net.

14 J13 -- 2-pin pin header. If a jumper installed, the battery BT2/BT3

will be connected to the V3P3SYS net.

15 SW3 PB

Pushbutton connected to the PB pin on the IC. This push-

button can be used in conjunction with the Demo Code to

wake the IC from sleep mode or LCD mode to brown-out

mode.

16 TP2 GND GND test point.

17 J3 IAN_IN, IAP_IN

2-pin header for the connection of the non-isolated shunt

used for neutral current measurement. This header is on

the bottom of the board.

18 SW4 SEGDIO53 Pushbutton for optional software function.

18a J25 ADC0/1 2-pin header that allows access to the neutral current input

pins on the 71M6543.

19 JP6

A jumper is placed across JP6 to activate the internal AC

power supply.

Caution: High Voltage! Do not touch!

19a J11, J15, J16 ADC8, ADC9,

ADC10

2-pin headers that allow access to the voltage input pins on

the 71M6543.

20 J9 NEUTRAL

The NEUTRAL voltage input. This input is connected to

V3P3. This input is a spade terminal mounted on the bot-

tom of the board.

21, 23, 25 J4, J6. J8

VA_IN, VB_IN,

VC_IN

Phase voltage inputs to the board. Each input has a resis-

tor divider that leads to the pin on the IC associated with

the voltage input to the ADC. These inputs have spade

terminals mounted on the bottom of the board.

Caution: High Voltage! Do not touch!

22 TP1 TMUXOUT,

TMUX2OUT

Test points for access to the TMUXOUT and TMU2XOUT

pins on the 71M6543.

24 U5 -- The IC 71M6543 soldered to the PCB.

26, 28, 29 J17, J18, J20 -- Two-pin headers for connection of the external shunt resis-

tors (REV 4.0) or CTs (REV 5.0) to the board.

27 JP53 V3P3D

2-pin header that connects the V3P3D pin to parts on the

board that use the V3P3D net for their power supply. For

supply current measurements in brownout mode, the

jumper on JP53 may be removed.

29a J22, J23, J24 ADC2/3, ADC4/5,

ADC5/6

2-pin headers that allow access to the current input pins on

the 71M6543.

30 J14 EMULATOR I/F 2x10 emulator connector port for the Signum ICE ADM-51

or for the Teridian TFP-2 Flash Programmer.

31 JP3 ICE_E

3-pin header for the control of the ICE_E signal. A jumper

across pins 1-2 disables the ICE interface; a jumper across

pins 2-3 enables it.

71M6543 Demo Board User’s Manual

Page: 57 of 91 v5

Item # Reference

Designator Name Use

32 JP44 GND 3-pin header that can be used to control the PE pin of the

µWire EEPROM.

33 TP3 GND GND test point.

34 JP54 -- 2-pin header that connects the SDCK signal to the serial

EEPROM.

35 JP51 -- Two-pin header for the clock signal to the µWire EEPROM.

Inserting a jumper in this header enables the clock.

36 JP50 -- Two-pin header for pulling low the CS input of the µWire

EEPROM.

37 CN1 USB PORT This connector is an isolated USB port for serial communi-

cation with the 71M6543.

38 JP7 -- 2-pin header connected to the VARh pulse LED

39 D6 VARh VARh pulse LED.

40 JP8 WPULSE 2-pin header connected to the Wh pulse LED

41 JP5 UART_RX

2-pin header for connection of the RX output of the isolated

USB port to the RX pin of the 71M6543. When the Demo

Board is communicating via the USB port, a jumper should

be installed on JP5. When the Demo Board is communi-

cating via the Debug Board plugged into J21, the jumper

should be removed.

42 JP20 5.0 VDC Circular connector for supplying the board with DC power.

Do not exceed 5.0 VDC at this connector!

71M6543 Demo Board User’s Manual

Page: 58 of 91 v5

Figure 3-1: 71M6543 REV 4.0 Demo Board - Board Description

Default jumper settings are indicated in yellow. Elements shown in blue are on the bottom side of the board.

22 20

12674

27 26 23

252829

29a 19a

18a

71M6543 Demo Board User’s Manual

Page: 59 of 91 v5

3.2 71M6543 REV 5.0 DEMO BOARD DESCRIPTION

The 71M6543 REV 5.0 Demo Board is largely identical to the 71M6543 REV 4.0 Demo Board. Figure 3-2

shows the top view of this board.

Figure 3-2: 71M6543 REV 5.0 Demo Board – Top View

71M6543 Demo Board User’s Manual

Page: 60 of 91 v5

3.3 BOARD HARDWARE SPECIFICATIONS

PCB Dimensions

Width, length 134 mm x 131 mm (5.276” x 5.157”)

Thickness 1.6mm (0.062”)

Height w/ components 40 mm (1.57”)

Environmental

Operating Temperature -40°…+85°C

Storage Temperature -40°C…+100°C

Power Supply

Using internal AC supply 100 V…240 V RMS

DC Input Voltage (powered from DC supply) 5.0 VDC ±0.3 V

Supply Current < 10 mA typical

Input Signal Range

AC Voltage Signal (VA, VB, VC) 0…240 V RMS

AC Current Signals (IA, IB, IC) from Shunt 0…19.64 mV RMS

AC Current Signals (IA, IB, IC) from CT 0…176.8 mV RMS

Interface Connectors

DC Supply (J20) Circular connector

Emulator (J14) 10x2 header, 0.05” pitch

Voltage Input Signals Spade terminals on PCB bottom

Current Input Signals 0.1” 1X2 headers on PCB bottom

USB port (PC Interface) USB connector

Debug Board (J2) 8x2 header, 0.1” pitch

SPI Interface 5x2 header, 0.1” pitch

Functional Specification

Program Memory 64 KB FLASH memory

NV memory 1Mbit serial EEPROM

Time Base Frequency 32.768kHz, ±20PPM at 25°C

Controls and Displays

RESET Push-button (SW5)

PB Push-button (SW3)

Numeric Display 3X8-digit LCD, 7 segments per digit, plus meter symbols

“Wh” red LED (D5)

“VARh” red LED (D6)

Measurement Range

Voltage 120…600 V rms (resistor division ratio 1:3,398)

Current Dependent on shunt resistance or CT winding ratio

71M6543 Demo Board User’s Manual

Page: 61 of 91 v5

4 APPENDIX

This appendix includes the following documentation, tables and drawings:

71M6543 Demo Board Description

71M6543 REV 4.0 Demo Board Electrical Schematic

71M6543 REV 4.0 Demo Board Bill of Materials

71M6543 REV 4.0 Demo Board PCB layers (copper, silk screen, top and bottom side)

Schematics comments

71M6543 REV 5.0 Demo Board Electrical Schematic

71M6543 REV 5.0 Demo Board Bill of Materials

71M6543 REV 5.0 Demo Board PCB layers (copper, silk screen, top and bottom side)

Debug Board Description

Debug Board Electrical Schematic

Debug Board Bill of Materials

Debug Board PCB layers (copper, silk screen, top and bottom side)

71M6543 IC Description

71M6543 Pin Description

71M6543 Pin-out

71M6543 Demo Board User’s Manual

Page: 62 of 91 v5

4.1 71M6543 DEMO BOARD REV 4.0 ELECTRICAL SCHEMATIC

Figure 4-1: Teridian 71M6543 REV 4.0 Demo Board: Electrical Schematic 1/4

Title

Size Document Number Rev

Date: Sheet of

D6540 4.0

71M6543 Meter Demo Board

2 5Friday , January 07, 2011

Pull JP53 for BRN

current measurements.

GND

TMUXOUT

TMUX2OUT

SEGDIO52

GND

UART_RX

V3P3SYS

SEGDIO4

GND

SEGDIO35

V3P3SYS

SEGDIO32

SEGDIO24

SPI_CK

+5V_USB

ICE_EN

GND

UART 1

GND

SEGDIO21

DIO5

SEGDIO33

SEGDIO13

SEGDIO22

GND

SEGDIO52

XPULSE

VARS

WATTS

V2P5

SEGDIO20

VBAT_RTC

V3P3SYS

VBAT

SEGDIO14

SEGDIO12

YPULSE

VPULSE

XTAL_GND

SEGDIO31

OPT_RX

ADC8

GND

WPULSE

SEGDIO19

ADC2

SEGDIO34

GND

SEGDIO15

SEGDIO32

PULSE OUTPUTS

SEGDIO10

OPT_TX

XTAL_GND

SEGDIO18

TMUX2OU T

WPULSE

ADC9

SEGDIO8

V3P3SYS

GND_USB

ADC3

TX& R XL ED

+5V_USB GND_USB

RX_USB

SEGDIO33

ICE_EN

SEGDIO16

COM3

SEGDIO17

SEGDIO10

Note: Place

C24, C25, Y1

close to U5

GND

TMUXOU T

VLCD

ICE_EN

VREF

COM4

SEGDIO34

VPULSE

SW3

R11 62

C26

0.1uF

R142

10K

J19

HDR5X2

SEGDIO16

R17

ADC10

XI N

+C45

10uF

JP55

HDR2X1

1 2

C63

0.1uF

SEGDIO17

C60

0.1uF

R144

10K

C50

1000pF

R109

10K

R18

J21

HDR8X2

910

11 12

13 14

15 16

C59

100pF

ADC4

U8 LCD VLS-6648

COM3

COM4

COM5

X5,1E,1F,7F,13F,13E

FE,13G,13D

7D,13A,13C

7C,13B,DP13

7G,14F,14E

7B,14G,14D

7A,14A,14C

DP7,14B,DP14

8F,15F,15E

8E,15G,15D

8D,15A,15C

8C,15B,DP15

8G,16F,16E

8B,16G,16D

8A,16A,16C

DP8,16B,DP16

9F,17F,17E

9E,17G,17D

9D,17A,17C

9G,17B,DP17

9C,18F,18E

9A,18G,18D

X7,X8,X6,9B,18A,18C

DP9,18B,DP18

X15,10E,10F,X9,X16,X22

28 DP12,12C,12B,X11,X20,X19 29

12D,12G,12A 30

X14,12E,12F,X12,X21 31

DP11,11C,11B 32

11D,11G,11A 33

X13,11E,11F,X10,X17,X18 34

DP10,10C,10B 35

10D,10G,10A 36

DP6,6C,6B 37

6D,6G,6A 38

X1,6E,6F 39

DP5,5C,5B 40

5D,5G,5A 41

X2,5E,5F 42

DP4,4C,4B 43

4D,4G,4A 44

X3,4E,4F 45

DP3,3C,3B 46

3D,3G,3A 47

X4,3E,3F 48

DP0,2C,2B 49

2D,2G,2A 50

DP2,2E,2F 51

DP1,1C,1B 52

1D,1G,1A 53

COM2 54

COM1 55

COM0 56

J14

ICE Header

1920

R104

10K

JP3

R107

10K

C28

0.1uF

R15

+C47

10uF

C22

0.1uF

C49

1000pF

TP1

HDR2X1

1 2

COM5

R138

10K

R137

V3P3SYS

J12

V3P3D

C57

1000pF

C73

4.7uF

32.768KHz

1 2

R103

10K

C64

0.1uF

R76

10K

C36

1000pF

V3P3D

SEGDIO23

C61

1000pF

R106

CN1

USB-W

VBUS

D-

D+

GND

C43

1000pF

L16

Ferrite Bead 600ohm

SEGDIO15

SEGDIO44

BT2

BATTERY

JP53

HDR2X1

Ferrite Bead 600ohm

C30

22pF

BT3

BATTERY

C52

1000pF

JP2

JP52

HDR2X1

C25

10pF

R74

10K

C70

0.1uF

SEGDIO25

C19

0.1uF

JP8

HDR2X1

1 2

R108

10K

1000pF

C21

0.1uF

R143

10K

R150

100

R12

100K

R13

100K

ADUM3201

VDD1

VOA

VIB

GND1

VDD2 8

VIA 7

VOB 6

GND2 5

C18

0.1uF

C51

0.1uF

C24

15pF

C74

0.1uF

C72

0.01uF

R79

100

R19

OPT_TX

JP51

HDR2X1

SW4

C20

0.1uF

TP2

100

JP44

C71

0.1uF

JP45

COM4

J13

V3P3D

C55

100pF

TP3

1 2

BP103

SDCK

JP54

HDR2X1

1 2

R10 62

SEGDIO40

UART_RX_ISO

SEGDIO14

GND_USB

JP5

HDR2X1

SER EEPROM (uWire)

CLK

4VSS 5

ORG 6

PE 7

VCC 8

D10

LED

VBAT

C62

0.1uF

SEGDIO43

C77

0.1uF

BT1

BATTERY

GND

VLCD

R77

100K DNP

LD274

C31

22pF

JP1

FT232RQ

VCCIO

R XD

RI#

GND

DSR#

DCD#

CTS#

CBUS4

CBUS2

CBUS3

USBDP

USBDM

3V3OUT

GND 17

RESET# 18

VCC 19

GND 20

CBUS1 21

CBUS0 22

NC 23

AGND 24

NC 25

TEST 26

OSCI 27

OSCO 28

NC 29

TXD 30

DTR# 31

RTS# 32

SLUG 33

R9 62

R151

10K

JP50

HDR2X1

SEGDIO9

SW5

R105

10K

COM5

SER EEPROM

GND

4SDA 5

SCL 6

WP 7

VCC 8

JP7

HDR2X1

1 2

R16

ADC1

V3P3SYS ADC3

ADC0

ADC5

ADC2

ADC8 ADC4

ADC10

ADC9

GND

ADC6

ADC7

GND

XPULSE

SEGDIO41

SEGDIO13

GND

COM0

SEGDIO18

SDATA

SEGDIO42

+5V_USB

ADC5

UAR T_TX

V3P3SYS

VBAT PB

VBAT_RTC

E_RXTX

SEGDIO35

V3P3D

SDCK

GND

UAR T_TX

TX_ U S B UART_RX_ISO

RX_USB

SEGDIO19

LCD

+5V_USB

GND_USB

V3P3SYS

SPI_CSZ

SEGDIO41

SEGDIO12

TMUX2OU T

V3P3D

GND

SEGDIO54

SDCK

YPULSE

V3P3SYS

GND

SPI_DO

XTAL_GND

V3P3D

SEGDIO28

GND

V3P3D

SEGDIO20

SEGDIO11

V3P3D

OPT_RX

ADC1

DIO4

SEGDIO40

GND

UART_TX

GND

SPI_DI

SERIAL EEPROM

GND

V3P3SYS

SEGDIO29

OPT_RX

SEGDIO29

COM1

71M6543-100TQFP

SPI_DI/SEGDIO38

SPI_DO/SEGDIO37

SPI_CSZ/SEGDIO36

SEGDIO35

SEGDIO34

SEGDIO33

SEGDIO32

SEGDIO31

SEGDIO30

SEGDIO29

SEGDIO28

COM0

COM1

COM2

COM3

SEGDIO27/COM4

SEGDIO26/COM5

SEGDIO25

SEGDIO24

SEGDIO23

SEGDIO22

SEGDIO21

SEGDIO20

SEGDIO19

SEGDIO18

NC 26

SEGDIO17 27

SEGDIO16 28

SEGDIO15 29

SEGDIO14 30

SEGDIO13 31

SEGDIO12 32

SEGDIO11 33

SEGDIO10 34

SEGDIO9 35

SEGDIO8 36

SEGDIO7 37

SEGDIO6 38

NC 40

SEGDIO4 41

SDATA 42

SDCK 43

VPULSE 44

WPULSE 45

OPT_RX/SEGDIO55 46

SEGDIO54 47

NC 48

NC 49

NC 50

SEGDIO53 51

SEGDIO52 52

OPT_TX/SEGDIO51 53

TX 54

RX 55

E_RST/SEG50 56

E_TCLK/SEG49 57

E_RXTX/SEG48 58

ICE_E 59

VDD 60

V3P3D 61

GNDD3 62

IADC7 63

IADC6 64

IADC5 65

IADC4 66

IADC3 67

IADC2 68

V3P3SYS 69

VBAT 70

VBAT_RTC 71

GNDA 72

NC 73

NC 74

XO U T

GNDA_K

TEST

VADC10

VADC9

VADC8

V3P3A_K

IADC1

IADC0

VREF

VLCD

RESET

TMUX2OUT/SEG46

SEGDIO45

SEGDIO44

SEGDIO43

SEGDIO42

SEGDIO41

SEGDIO40

SPI_CK/SEGDIO39

100

TMUXOUT/SEG47

SEGDIO5 39

XIN 75

ADC6

V3P3D

GND

SEGDIO21

GND_USB

E_RST

E_TCLK

SEGDIO8

E_TCLK

SEGDIO28

+5V

BIT BANG HDR

TMUXOU T

ADC0

V3P3SYS

USB Connector, straight

SEGDIO53

GND

COM2

OPT_TX

SEGDIO30

GND

SEGDIO54

E_RST

GND

SEGDIO30

E _R XT X

ADC7

SEGDIO22

GND

UART_RX

GND

SEGDIO25

EMULATOR I/F

GND

COM3

SEGDIO11

SDATA

SEGDIO20

SEGDIO21

SEGDIO18

SEGDIO32

SEGDIO19

SEGDIO31

COM0

SEGDIO33

SEGDIO17

SEGDIO44

SEGDIO15

SEGDIO34

COM1

SEGDIO16

SEGDIO40

SEGDIO14

SEGDIO43

COM2

SEGDIO11

SEGDIO12

SEGDIO42

SEGDIO13

SEGDIO22

SEGDIO25

SEGDIO30

SEGDIO29

SEGDIO35

SEGDIO24

SEGDIO31

GND

V3P3D

SPI_DO

SPI_CK

SPI_CSZ

SPI_DI

SEGDIO23

SEGDIO24

71M6543 Demo Board User’s Manual

Page: 63 of 91 v5

Figure 4-2: Teridian 71M6543 REV 4.0 Demo Board: Electrical Schematic 2/4

NEUTRAL

Fr om NEUTRA L

terminal.

V B_IN

NEUTRAL

V C_IN

NEUTRAL

5VDC

NEUTRAL

R6, R7, R8 can be used to

generate a virtual neutral.

V3P3SYS

VA_IN

L17

Ferrite Bead 600ohm

+C2

22uF

RV2

VARISTOR

ES1J

0.1uF

D12

S1J

D14

S1J

R73

100

C44

1000pF

R110

R20

8.06K

L18

Ferrite Bead 600ohm

R111

4.02K

C46

0.03 uF

R65

100

C54

0.1uF

DNP

R146

3.4K

S1J

+C39

100uF

JP4

C53

1000pF

C35

2.2uF

75K

DNP

TL431

RV3

VARISTOR

180uH

R152

D13

S1J

75K

DNP

LNK304-TN

4S1 5

S2 6

S3 7

S4 8

75K

DNP

+C7

10uF

R149

R21

25.5K

JP20

D17

1.5KE350A

JP6

R139

1.5

C42

1000pF

RV1

VARISTOR

R141

100

R147

3.4K

10uF

C27

0.1uF

R140

3.4K

R148

820

V3P3SYS

GND

VB_IN

VC_IN

NEUTRAL

VA_IN

NEUTRAL

GND

VB_IN

VC_IN

L_RECT

Title

Size Document Number Rev

Date: Sheet of

D6543 4.0

71M6543 Meter Demo Board

3 5Wednesday , December 15, 2010

71M6543 Demo Board User’s Manual

Page: 64 of 91 v5

Figure 4-3: Teridian 71M6543 REV 4.0 Demo Board: Electrical Schematic 3/4

U17

71M6103-8SOIC

VCC 1

SP 2

SN 3

GND 4

TMUX

INP

INN

TEST

U15

71M6103-8SOIC

VCC 1

SP 2

SN 3

GND 4

TMUX

INP

INN

TEST

U16

71M6103-8SOIC

VCC 1

SP 2

SN 3

GND 4

TMUX

INP

INN

TEST

R96

499

R93

499

R89 499

C37

1000pF

DNP

R94

499

R81

10K

R90 499

R25

3.4

100 PPM

ADC0

ADC1

C41

1000pF

DNP

C65

1000pF

C67

1000pF

IADC2/IADC3 PINS

Population options f or R29, R28, R24, etc.

w hen using CTs:

2 x 3.4 Ohm, 100 PPM - Vishay/Dale CRCW12063R40FKEA,

Digi-Key P/N 541-3.40FFCT-ND (1206), or

3 x 5.1 Ohm, 50 PPM - Vishay/Dale SMM02040C5108FB300,

Mouser P/N 71-SMM02040C5108FB30

C68

1000pF

R97, R92, R91, etc. are through-hole

1/8 W parts in order to provide enough

pin-to-pin distance to accommodate the

clearance and creepage required.

750110056

0 Ohm

C38

1000pF

DNP

INN_IN

INP_IN

0 Ohm

GND

R30

3.4

DNP

100 PPM

R31

3.4

DNP

100 PPM

R91

0DNP

IADC4/IADC5 PINS

R100

0DNP

IADC6/IADC7 PINS

1.08 : 1

J23

V3P3SYS

R34

3.4

DNP

100 PPM

* *

750110056

This channel used for Phase A sensors.

ADC5

GND_R6000_B

IACP/IAN PINS

ADC0/ADC1

IBP_IN

IBN_IN

IC_IN

C32

1000pF

DNP

This channel used for Phase C sensors.

* *

ADC4

Alternative footprint option for

Midcom 750110057 (8 kV) to

be provided on daughter boards.

This channel used for Phase B sensors.

R101

0DNP

0 Ohm

* *

GND_R6000_A

IA P_IN

IA N_IN

IB_IN

C69

1000pF

Isolation Barrier

750110056

GND

Population Options:

Part 71M6xxx CT Option

R26, R27 DNP 3.4 Ohm 1206 (100 PPM), or

R26,R27,R32 DNP 5.1 Ohm MELF (50 PPM)

R89, R90 499 Ohm 10 kOhm

R97, R92 DNP 750 Ohm

C48, C58 1,000pF 1,000 pF

R91 DNP 0 Ohm

U15 71M6103 DNP

T4 MidCom-56 DNP

C17 1 uF DNP

This channel used for NEUTRAL. No isolation, and no remote sensor.

R92

750 DNP

IN_IN

ADC3

R98

750 DNP

Title

Size Document Number Rev

Date: Sheet of

D6543 4.0

71M6543 Meter Demo Board

4 5Thursday , January 06, 2011

R28

3.4

DNP

100 PPM

R29

3.4

DNP

100 PPM

ADC2

R97

750 DNP

R36

3.4

DNP

100 PPM

R35

3.4

DNP

100 PPM

R102

750 DNP

C48

1000pF

ADC7

R26

3.4

DNP

100 PPM

R27

3.4

DNP

100 PPM

C58

1000pF

J22

C29

1000pF

DNP

C40

1000pF

DNP

R112

750 DNP

ADC6

L10

0 Ohm

GND_R6000_C

R99

750 DNP

J24

R54

750

ICP_IN

ICN_IN

IA_IN

R82

10K

R24

3.4

100 PPM

J20

R14

750

C17

1uF

1000pF

J17

C56

1uF

0 Ohm

J25

0 Ohm

C66

0.1uF

J18

R95

499

C14

1000pF

R32

3.4

DNP

100 PPM

C34

1uF

71M6543 Demo Board User’s Manual

Page: 65 of 91 v5

Figure 4-4: Teridian 71M6543 REV 4.0 Demo Board: Electrical Schematic 4/4

GND

Title

Size Document Number Rev

Date: Sheet of

DB6543 4.0

<Title>

5 5Wednesday , December 15, 2010

V A DC8 PIN

V A DC9 PIN

V A DC10 PIN

R38

4.7K

R46

270K

R63

R62

270K

J11

V3P3SYS

J16

J15

VC_IN

L11

Ferrite Bead 600ohm

L13

Ferrite Bead 600ohm

L12

Ferrite Bead 600ohm

1000pF

R72

750

R47

270K

R39

4.7K

R66

R64

270K

C11

1000pF

ADC10

C13

1000pF

ADC8

VA_IN

R33

750

VB_IN

R58

4.7K

ADC9

R60

270K

R59

270K

R52

750

R61

ADC10

VC_IN

VA_IN

VB_IN

NEUTRA L

GND

C15

1000pF

VOLTAGE

CONNECTIONS

NEUTRAL

11NEUTRAL

If high-precision Rs are not available, use:

Vishay P/N RN65D2004FB14

Mouser P/N 71-RN65D-F-2.0M

TC = 100 PPM/C

71M6543 Demo Board User’s Manual

Page: 66 of 91 v5

4.2 71M6543 DEMO BOARD REV 5.0 ELECTRICAL SCHEMATIC

Figure 4-5: Teridian 71M6543 REV 5.0 Demo Board: Electrical Schematic 1/4

Title

Size Document Number Rev

Date: Sheet of

D6540 5.0

71M6543 Meter Demo Board

1 3Friday , January 07, 2011

Pull JP53 for BRN

current measurements.

GND

TMUXOUT

TMUX2OUT

SEGDIO52

GND

UART_RX

V3P3SYS

SEGDIO4

GND

SEGDIO35

V3P3SYS

SEGDIO32

SEGDIO24

SPI_CK

+5V_USB

ICE_EN

GND

UART 1

GND

SEGDIO21

DIO5

SEGDIO33

SEGDIO13

SEGDIO22

GND

SEGDIO52

XPULSE

VARS

WATTS

V2P5

SEGDIO20

VBAT_RTC

V3P3SYS

VBAT

SEGDIO14

SEGDIO12

YPULSE

VPULSE

XTAL_GND

SEGDIO31

OPT_RX

ADC8

GND

WPULSE

SEGDIO19

ADC2

SEGDIO34

GND

SEGDIO15

SEGDIO32

PULSE OUTPUTS

SEGDIO10

OPT_TX

XTAL_GND

SEGDIO18

TMUX2OU T

WPULSE

ADC9

SEGDIO8

V3P3SYS

GND_USB

ADC3

TX& R XL ED

+5V_USB GND_USB

RX_USB

SEGDIO33

ICE_EN

SEGDIO16

COM3

SEGDIO17

SEGDIO10

Note: Place

C24, C25, Y1

close to U5

GND

TMUXOU T

VLCD

ICE_EN

VREF

COM4

SEGDIO34

VPULSE

SW3

R11 62

C26

0.1uF

R142

10K

J19

HDR5X2

SEGDIO16

R17

ADC10

XI N

+C45

10uF

JP55

HDR2X1

1 2

C63

0.1uF

SEGDIO17

C60

0.1uF

R144

10K

C50

1000pF

R109

10K

R18

J21

HDR8X2

910

11 12

13 14

15 16

C59

100pF

ADC4

U8 LCD VLS-6648

COM3

COM4

COM5

X5,1E,1F,7F,13F,13E

FE,13G,13D

7D,13A,13C

7C,13B,DP13

7G,14F,14E

7B,14G,14D

7A,14A,14C

DP7,14B,DP14

8F,15F,15E

8E,15G,15D

8D,15A,15C

8C,15B,DP15

8G,16F,16E

8B,16G,16D

8A,16A,16C

DP8,16B,DP16

9F,17F,17E

9E,17G,17D

9D,17A,17C

9G,17B,DP17

9C,18F,18E

9A,18G,18D

X7,X8,X6,9B,18A,18C

DP9,18B,DP18

X15,10E,10F,X9,X16,X22

28 DP12,12C,12B,X11,X20,X19 29

12D,12G,12A 30

X14,12E,12F,X12,X21 31

DP11,11C,11B 32

11D,11G,11A 33

X13,11E,11F,X10,X17,X18 34

DP10,10C,10B 35

10D,10G,10A 36

DP6,6C,6B 37

6D,6G,6A 38

X1,6E,6F 39

DP5,5C,5B 40

5D,5G,5A 41

X2,5E,5F 42

DP4,4C,4B 43

4D,4G,4A 44

X3,4E,4F 45

DP3,3C,3B 46

3D,3G,3A 47

X4,3E,3F 48

DP0,2C,2B 49

2D,2G,2A 50

DP2,2E,2F 51

DP1,1C,1B 52

1D,1G,1A 53

COM2 54

COM1 55

COM0 56

J14

ICE Header

1920

R104

10K

JP3

R107

10K

C28

0.1uF

R15

+C47

10uF

C22

0.1uF

C49

1000pF

TP1

HDR2X1

1 2

COM5

R138

10K

R137

V3P3SYS

J12

V3P3D

C57

1000pF

C73

4.7uF

32.768KHz

1 2

R103

10K

C64

0.1uF

R76

10K

C36

1000pF

V3P3D

SEGDIO23

C61

1000pF

R106

CN1

USB-B

VBUS

D-

D+

GND

C43

1000pF

L16

Ferrite Bead 600ohm

SEGDIO15

SEGDIO44

BT2

BATTERY

JP53

HDR2X1

1 2

Ferrite Bead 600ohm

C30

22pF

BT3

BATTERY

C52

1000pF

JP2

JP52

HDR2X1

1 2

C25

10pF

R74

10K

C70

0.1uF

SEGDIO25

C19

0.1uF

JP8

HDR2X1

R108

10K

1000pF

C21

0.1uF

R143

10K

R150

100

R12

100K

R13

100K

ADUM3201

VDD1

VOA

VIB

GND1

VDD2 8

VIA 7

VOB 6

GND2 5

C18

0.1uF

C51

0.1uF

C24

15pF

C74

0.1uF

C72

0.01uF

R79

100

R19

OPT_TX

JP51

HDR2X1

1 2

SW4

C20

0.1uF

TP2

100

JP44

C71

0.1uF

JP45

COM4

J13

V3P3D

C55

100pF

TP3

1 2

BP103

SDCK

JP54

HDR2X1

1 2

R10 62

SEGDIO40

UART_RX_ISO

SEGDIO14

GND_USB

JP5

HDR2X1

SER EEPROM (uWire)

CLK

4VSS 5

ORG 6

PE 7

VCC 8

D10

LED

VBAT

C62

0.1uF

SEGDIO43

C77

0.1uF

BT1

BATTERY

GND

VLCD

R77

100K DNP

LD274

C31

22pF

JP1

FT232RQ

VCCIO

R XD

RI#

GND

DSR#

DCD#

CTS#

CBUS4

CBUS2

CBUS3

USBDP

USBDM

3V3OUT

GND 17

RESET# 18

VCC 19

GND 20

CBUS1 21

CBUS0 22

NC 23

AGND 24

NC 25

TEST 26

OSCI 27

OSCO 28

NC 29

TXD 30

DTR# 31

RTS# 32

SLUG 33

R9 62

R151

10K

JP50

HDR2X1

1 2

SEGDIO9

SW5

R105

10K

COM5

SER EEPROM

GND

4SDA 5

SCL 6

WP 7

VCC 8

JP7

HDR2X1

1 2

R16

ADC1

V3P3SYS ADC3

ADC0

ADC5

ADC2

ADC8 ADC4

ADC10

ADC9

GND

ADC6

ADC7

GND

XPULSE

SEGDIO41

SEGDIO13

GND

COM0

SEGDIO18

SDATA

SEGDIO42

+5V_USB

ADC5

UAR T_TX

V3P3SYS

VBAT PB

VBAT_RTC

E_RXTX

SEGDIO35

V3P3D

SDCK

GND

UAR T_TX

TX_ U S B UART_RX_ISO

RX_USB

SEGDIO19

LCD

+5V_USB

GND_USB

V3P3SYS

SPI_CSZ

SEGDIO41

SEGDIO12

TMUX2OU T

V3P3D

GND

SEGDIO54

SDCK

YPULSE

V3P3SYS

GND

SPI_DO

XTAL_GND

V3P3D

SEGDIO28

GND

V3P3D

SEGDIO20

SEGDIO11

V3P3D

OPT_RX

ADC1

DIO4

SEGDIO40

GND

UART_TX

GND

SPI_DI

SERIAL EEPROM

GND

V3P3SYS

SEGDIO29

OPT_RX

SEGDIO29

COM1

71M6543-100TQFP

SPI_DI/SEGDIO38

SPI_DO/SEGDIO37

SPI_CSZ/SEGDIO36

SEGDIO35

SEGDIO34

SEGDIO33

SEGDIO32

SEGDIO31

SEGDIO30

SEGDIO29

SEGDIO28

COM0

COM1

COM2

COM3

SEGDIO27/COM4

SEGDIO26/COM5

SEGDIO25

SEGDIO24

SEGDIO23

SEGDIO22

SEGDIO21

SEGDIO20

SEGDIO19

SEGDIO18

NC 26

SEGDIO17 27

SEGDIO16 28

SEGDIO15 29

SEGDIO14 30

SEGDIO13 31

SEGDIO12 32

SEGDIO11 33

SEGDIO10 34

SEGDIO9 35

SEGDIO8 36

SEGDIO7 37

SEGDIO6 38

NC 40

SEGDIO4 41

SDATA 42

SDCK 43

VPULSE 44

WPULSE 45

OPT_RX/SEGDIO55 46

SEGDIO54 47

NC 48

NC 49

NC 50

SEGDIO53 51

SEGDIO52 52

OPT_TX/SEGDIO51 53

TX 54

RX 55

E_RST/SEG50 56

E_TCLK/SEG49 57

E_RXTX/SEG48 58

ICE_E 59

VDD 60

V3P3D 61

GNDD3 62

IADC7 63

IADC6 64

IADC5 65

IADC4 66

IADC3 67

IADC2 68

V3P3SYS 69

VBAT 70

VBAT_RTC 71

GNDA 72

NC 73

NC 74

XO U T

GNDA_K

TEST

VADC10

VADC9

VADC8

V3P3A_K

IADC1

IADC0

VREF

VLCD

RESET

TMUX2OUT/SEG46

SEGDIO45

SEGDIO44

SEGDIO43

SEGDIO42

SEGDIO41

SEGDIO40

SPI_CK/SEGDIO39

100

TMUXOUT/SEG47

SEGDIO5 39

XIN 75

ADC6

V3P3D

GND

SEGDIO21

GND_USB

E_RST

E_TCLK

SEGDIO8

E_TCLK

SEGDIO28

+5V

BIT BANG HDR

TMUXOU T

ADC0

V3P3SYS

USB Connector, straight

SEGDIO53

GND

COM2

OPT_TX

SEGDIO30

GND

SEGDIO54

E_RST

GND

SEGDIO30

E _R XT X

ADC7

SEGDIO22

GND

UART_RX

GND

SEGDIO25

EMULATOR I/F

GND

COM3

SEGDIO11

SDATA

SEGDIO20

SEGDIO21

SEGDIO18

SEGDIO32

SEGDIO19

SEGDIO31

COM0

SEGDIO33

SEGDIO17

SEGDIO44

SEGDIO15

SEGDIO34

COM1

SEGDIO16

SEGDIO40

SEGDIO14

SEGDIO43

COM2

SEGDIO11

SEGDIO12

SEGDIO42

SEGDIO13

SEGDIO22

SEGDIO25

SEGDIO30

SEGDIO29

SEGDIO35

SEGDIO24

SEGDIO31

GND

V3P3D

SPI_DO

SPI_CK

SPI_CSZ

SPI_DI

SEGDIO23

SEGDIO24

71M6543 Demo Board User’s Manual

Page: 67 of 91 v5

Figure 4-6: Teridian 71M6543 REV 5.0 Demo Board: Electrical Schematic 2/4

NEUTRAL

Fr om NEUTRA L

terminal.

V B_IN

NEUTRAL

V C_IN

NEUTRAL

5VDC

NEUTRAL

R6, R7, R8 can be used to

generate a virtual neutral.

V3P3SYS

VA_IN

L17

Ferrite Bead 600ohm

+C2

22uF

RV2

VARISTOR

ES1J

0.1uF

D12

S1J

D14

S1J

R73

100

C44

1000pF

R110

R20

8.06K

L18

Ferrite Bead 600ohm

R111

4.02K

C46

0.03 uF

R65

100

C54

0.1uF

DNP

R146

3.4K

S1J

+C39

100uF

JP4

C53

1000pF

C35

2.2uF

75K

DNP

TL431

RV3

VARISTOR

180uH

R152

D13

S1J

75K

DNP

LNK304-TN

4S1 5

S2 6

S3 7

S4 8

75K

DNP

+C7

10uF

R149

R21

25.5K

JP20

D17

1.5KE350A

JP6

R139

1.5

C42

1000pF

RV1

VARISTOR

R141

100

R147

3.4K

10uF

C27

0.1uF

R140

3.4K

R148

820

V3P3SYS

GND

VB_IN

VC_IN

NEUTRAL

VA_IN

NEUTRAL

GND

VB_IN

VC_IN

L_RECT

Title

Size Document Number Rev

Date: Sheet of

D6543 5.0

71M6543 Meter Demo Board

2 3Thursday , December 09, 2010

71M6543 Demo Board User’s Manual

Page: 68 of 91 v5

Figure 4-7: Teridian 71M6543 REV 5.0 Demo Board: Electrical Schematic 3/4

U17

71M6103-8SOIC

DNP

VCC 1

SP 2

SN 3

GND 4

TMUX

INP

INN

TEST

U15

71M6103-8SOIC

DNP

VCC 1

SP 2

SN 3

GND 4

TMUX

INP

INN

TEST

U16

71M6103-8SOIC

DNP

VCC 1

SP 2

SN 3

GND 4

TMUX

INP

INN

TEST

R96

10K

R93

10K

R89 10K

C37

1000pF

R94

10K

R81

10K

R90 10K

R25

5.1

50 PPM

ADC0

ADC1

C41

1000pF

C65

1000pF

DNP

C67

1000pF

DNP

IADC2/IADC3 PINS

Population options f or R29, R28, R24, etc.

w hen using CTs:

2 x 3.4 Ohm, 100 PPM - Vishay/Dale CRCW12063R40FKEA,

Digi-Key P/N 541-3.40FFCT-ND (1206), or

3 x 5.1 Ohm, 50 PPM - Vishay/Dale SMM02040C5108FB300,

Mouser P/N 71-SMM02040C5108FB30

C68

1000pF

DNP

R97, R92, R91, etc. are through-hole

1/8 W parts in order to provide enough

pin-to-pin distance to accommodate the

clearance and creepage required.

750110056

DNP

0 Ohm

C38

1000pF

INN_IN

INP_IN

0 Ohm

GND

R30

5.1

50 PPM

R31

5.1

50 PPM

R91

IADC4/IADC5 PINS

R100

IADC6/IADC7 PINS

1.08 : 1

J23

V3P3SYS

R34

5.1

50 PPM

* *

750110056

DNP

This channel used for Phase A sensors.

ADC5

GND_R6000_B

IACP/IAN PINS

ADC0/ADC1

IBP_IN

IBN_IN

IC_IN

C32

1000pF

This channel used for Phase C sensors.

* *

ADC4

Alternative footprint option for

Midcom 750110057 (8 kV) to

be provided on daughter boards.

This channel used for Phase B sensors.

R101

0 Ohm

* *

GND_R6000_A

IA P_IN

IA N_IN

IB_IN

C69

1000pF

DNP

Isolation Barrier

750110056

DNP

GND

Population Options:

Part 71M6xxx CT Option

R26, R27 DNP 3.4 Ohm 1206 (100 PPM), or

R26,R27,R32 DNP 5.1 Ohm MELF (50 PPM)

R89, R90 499 Ohm 10 kOhm

R97, R92 DNP 750 Ohm

C48, C58 DNP 1,000 pF

C29, C32 DNP 1,000 pF

R91 DNP 0 Ohm

U15 71M6xxx DNP

T4 MidCom - 56 DNP

C17 1 uF DNP

L9, L10 0 Ohm 600 Ohm ferrite

This channel used for NEUTRAL. No isolation, and no remote sensor.

R92

750

IN_IN

ADC3

R98

750

Title

Size Document Number Rev

Date: Sheet of

D6543 5.0

71M6543 Meter Demo Board

3 3Thursday , March 24, 2011

R28

5.1

50 PPM

R29

5.1

50 PPM

ADC2

R97

750

R36

5.1

50 PPM

R35

5.1

50 PPM

R102

750

C48

1000pF

DNP

ADC7

R26

5.1

50 PPM

R27

5.1

50 PPM

C58

1000pF

DNP

J22

C29

1000pF

C40

1000pF

R112

750

ADC6

L10

0 Ohm

GND_R6000_C

R99

750

J24

R54

750

ICP_IN

ICN_IN

IA_IN

R82

10K

R24

5.1

50 PPM

J20

R14

750

C17

1uF

DNP

1000pF

J17

C56

1uF

DNP

0 Ohm

J25

0 Ohm

C66

0.1uF

J18

R95

10K

C14

1000pF

R32

5.1

50 PPM

C34

1uF

DNP

71M6543 Demo Board User’s Manual

Page: 69 of 91 v5

Figure 4-8: Teridian 71M6543 REV 5.0 Demo Board: Electrical Schematic 4/4

TC = 100 PPM/C

All Susumu resistors: TC = 25 PPM/C

GND

Title

Size Document Number Rev

Date: Sheet of

DB6543 5.0

<Title>

1 1Friday , January 07, 2011

V A DC8 PIN

V A DC9 PIN

V A DC10 PIN

R38

4.7K

R46

270K

R63

R62

270K

J11

V3P3SYS

J16

J15

VC_IN

L11

Ferrite Bead 600ohm

L13

Ferrite Bead 600ohm

L12

Ferrite Bead 600ohm

1000pF

R72

750

R47

270K

R39

4.7K

R66

R64

270K

C11

1000pF

ADC10

C13

1000pF

ADC8

VA_IN

R33

750

VB_IN

R58

4.7K

ADC9

R60

270K

R59

270K

R52

750

R61

ADC10

VC_IN

VA_IN

VB_IN

NEUTRA L

GND

C15

1000pF

VOLTAGE

CONNECTIONS

NEUTRAL

11NEUTRAL

If high-precision Rs are not available, use:

Vishay P/N RN65D2004FB14

Mouser P/N 71-RN65D-F-2.0M

TC = 100 PPM/C

71M6543 Demo Board User’s Manual

Page: 70 of 91 v5

4.3 COMMENTS ON SCHEMATICS

4.3.1 GENERAL

The schematics shown in this document are provided for a Demo Meter that functions under laboratory conditions.

Maxim does not guarantee proper function of a meter under field conditions when using the Demo Board schematics.

Care should be taken by the meter designer that all applicable design rules as well as reliability, safety and legal

regulations are met by the meter design.

4.3.2 USING FERRITES IN THE SHUNT SENSOR INPUTS

The 71M6543 Demo Board in shunt configuration has footprints on the PCB to accommodate ferrites between the

shunt signal inputs and the 71M6xxxx Remote Sensors. These footprints, labeled L4, L5, L6, L7, L9, and L10, are

populated with 0-Ohm resistors. It is not advisable to directly replace these resistors with ferrites without further

changes, since this will degrade the low-current accuracy to some degree.

If ferrites are needed for EMC reasons, the input circuit should be modified as shown in Figure 4-9. The modifications

are as follows:

• Positions L4, L5, L6, etc. are replaced with ferrites.

• A 10Ω resistor is added across the sensor input.

• The two 1,000 pF capacitors from INP to local ground and from INN to local ground are replaced with

10,000 pF or higher value capacitors.

Figure 4-9: Input Circuit with Ferrites

R51

10.0

U19

71M6103-8SOIC

VCC 1

SP 2

SN 3

GND 4

TMUX

INP

INN

TEST

R115 499

R117 499

R118

0DNP

1.08 : 1

* *

750110056

GND_R6000_A

IA P_IN

IA N_IN

R121

750 DNP IA

R123

750 DNP

C83

10,000pF

R49

3.4

DNP

C84

10,000pF

R50

3.4

DNP

L22

600 Ohm f errite

L21

600 Ohm f errite

IA_IN J30

C23

1uF

R53

3.4

DNP

71M6543 Demo Board User’s Manual

Page: 71 of 91 v5

4.4 71M6543 DEMO BOARD REV 4.0 BILL OF MATERIAL

Table 4-1: 71M6543 REV 4.0 Demo Board: Bill of Material (1/2)

Item QReference Part Footprint Digi-Key P/N Mous er P/N Manufacturer Manufacturer P/N Tol Rating HDR DNP

1 2 BT1 ,BT2 BATTERY

BAT 3 PIN

BARREL

COMBO

DNP

2 1 BT3 BATTERY

BAT CR2032

MAX

DNP

3 1 CN1 USB-W

USBV

806-KUSBVX-

BS1N-W

Kycon KUSBVX-BS1N-W

423 C1,C8,C9,C11,C13,C14,C15, 1000pF

603 445-1298-1-ND TDK C1608X7R2A102K 10% 100V

C36,C42,C43,C44,C48,C49,

C50,C52,C53,C57,C58,C61,

C65,C67,C68,C69

5 1 C2 22uF

SM/CT_3216 478-1663-1-ND AVX TAJA226K010RNJ 10% 10V

618 C3,C5,C18,C19,C20,C21, 0.1uF

603 445-1314-1-ND TDK C1608X7R1H104K 0.1 50V

C22,C26,C27,C28,C51,C60,

C62,C63,C64,C66,C74,C77

7 4 C6,C7,C45,C47 10uF

SM/CT_3216 478-1654-1-ND AVX TAJA106K010R 0.1 10V

8 3 C17,C34,C56 1uF

603 445-1604-1-ND TDK C1608X7R1C105K 10% 16V

9 1 C24 15pF

603 445-1271-1-ND TDK C1608C0G1H150J 5% 50V

10 1C25 10pF

603 445-1269-1-ND TDK C1608C0G1H100D 5% 50V

11 6C29,C32,C37,C38,C40,C41 1000pF

603 445-1298-1-ND TDK C1608X7R2A102K 10% 100V DNP

12 2C30,C31 22pF

603 445-1273-1-ND TDK C1608C0G1H220J 0.05 50V

13 1C35 2.2uF

CYL/D.400/LS.

200/.034

493-1227-ND Nichicon UVR2G2R2MPD 400V

14 1C39 100uF

CYL/D.400/LS.

200/.034

P963-ND Panasonic ECE-A1AKS101 20% 10V

15 1C46 0.03 uF

HIGH VOLT

DISC CAP

75-125LS30-R Vishay/BC 125LS30-R 1000V

16 1C54 0.1uF

603 445-1314-1-ND TDK C1608X7R1H104K 0.1 50V DNP

17 2C55,C59 100pF

603 445-1281-1-ND TDK C1608C0G1H101J 5% 50V

18 2C70,C71 0.1uF

805 478-3351-1-ND

AVX Corporatio

08055C104MAT2A 20% 50V

19 1C72 0.01uF

603 478-1227-1-ND

AVX Corporatio

06035C103KAT2A 0.1 50V

20 1C73 4.7uF

805 587-1782-1-ND Taiyo Yuden TMK212BJ475KG-T 0.1 25V

21 2D5,D6 LED_1

LED6513 67-1612-ND Lumex SSL-LX5093SRC/E

22 1D7 LD274

LED6513 475-1461-ND Osra m SFH 4511

23 4D8,D12,D13,D14 S1J

SMA/DIODE S1J -E3/61TGICT-ND

Vishay/Genera

S1J-E3/61T

24 1D9 ES1J

SMA/DIODE ES1JFSCT-ND Vishay ES1J

25 1D10 LED

805 L62415CT-ND CML CMD17-21UGC/TR8

26 1D17 1.5KE350A

DO-41 1.5KE350CALFCT-ND Littelfuse 1.5KE350CA

27 5JP1,J1,JP3,JP44,JP45 HDR3X1

BLKCON.100/V

H/TM1SQ/W.1

00/3

S1011E-36-ND Sullins PBC36SAAN 0.1

28 1JP2 HDR5X1

BLKCON.100/V

H/TM1SQ/W.1

00/5

S1011E-36-ND Sullins PBC36SAAN 0.2

29 25 TP1,J3,JP4,JP5,JP6,JP7, HDR2X1

BLKCON.100/V

H/TM1SQ/W.1

00/2

S1011E-36-ND Sullins PBC36SAAN 0.1

JP8,J11,J12,J13,J15,J16,

J17,J18,J20,J22,J23,J24,

J25,JP50,JP51,JP52,JP53,

JP54,JP55

30 1JP20 SWITCHCRAFT

SWITCHCRAFT SC237-ND

Switchcraft Inc.

RAPC712X

31 4J4,J6,J8,J9 Spade Terminal

FASTON A24747CT-ND Tyco/AMP 62395-1

32 1J14 ICE Header

RIBBON6513O

UTLINE

A33555-ND

571-5-104068-

Tyco/AMP 5-104068-1

33 1J19 HDR5X2

BLKCON.100/V

H/TM2OE/W.2

00/10

S2011E-36-ND Sullins PBC36DAAN 0.2

34 1J21 HDR8X2

BLKCON.100/V

H/TM2OE/W.2

00/16

S2011E-36-ND Sullins PBC36DAAN 0.3

35 7L1,L11,L12,L13,L16,L17,

Ferrite Bead 600oh

805 445-1556-1-ND TDK MMZ2012S601A 0.5A

L18

36 8L2,L3,L4,L5,L6,L7,L9,L10 0 Ohm

805 RMCF0805ZT0R00CT-ND Stackpole RMCF0805ZT0R00 0.5A

37 1L8 180uH

RFB0807 CoilCraft RFB0807-181L

38 1Q1 BP103

LED6513 475-1437-ND Osra m SFH 300-3/4 DNP

39 3RV1,RV2,RV3 VARISTOR

MOV CPS

2381594

594-2381-594-

55116

AVX 2381 594 55116

71M6543 Demo Board User’s Manual

Page: 72 of 91 v5

Table 4-2: 71M6543 REV 4.0 Demo Board: Bill of Material (2/2)

Item QReference Part Footprint Digi-Key P/N Mous er P/N Manufacturer Manufacturer P/N Tol Rating HDR DNP

40 2R1,R2 1K

805 541-1.0KACT-ND Vishay/Dale CRCW08051K00JNEA 5%

0.125W

41 1R4 100

805 541-100ACT-ND Vishay/Dale CRCW0805100RJNEA 5%

0.125W

42 3R6,R7,R8 75K

AXLE FLAME

UPRIGHT

75KW-2-ND Yageo RSF200JB-75K 5% 2W DNP

43 6R9,R10,R11,R15,R16,R17 62

603 P62GCT-ND Panasonic ERJ-3GEYJ620V 5% 0.1W

44 2R12,R13 100K

603 P100KGCT-ND Panasonic ERJ-3GEYJ104V 5% 0.1W

45 5R14,R33,R52,R54,R72 750

805 RR12P750DCT-ND Susumu RR1220P-751-D 0.01 0.1W

46 1R18 0

1206 RHM0.0ECT-ND

Rohm Semicond

MCR18EZHJ000 0.05 0.25W

47 3R19,R106,R137 1K

603 P1.00KHCT-ND Panasonic ERJ-3EKF1001V 1% 0.1W

48 1R20 8.06K

805 RHM8.06KCCT-ND Rohm MCR10EZHF8061 1%

0.125W

49 1R21 25.5K

805 P25.5KCCT-ND Panasonic ERJ-6ENF2552V 1%

0.125W

50 2R24,R25 3.4

1206 541-3.40FFCT-ND Vishay/Dale CRCW08053R40FNEA 1%

0.125W

51 10 R26,R27,R28,R29,R30,R31, 3.4

1206 541-3.40FFCT-ND Vishay/Dale CRCW08053R40FNEA 0.01

0.125W

DNP

R32,R34,R35,R36

52 3R38,R39,R58 4.7K

805 RG20P4.7KBCT-ND TDK RG2012P-472-B-T5 0%

0.125W

53 6R46,R47,R59,R60,R62,R64 270K

805 RG20P270KBCT-ND Susumu RG2012P-274-B-T5 0%

0.125W

54 3R61,R63,R66 2M

AXLE FLAME

UPRIGHT

71-RN65D-F-

2.0M

Vishay/Dale RN65D2004FB14 0.01 0.5W

55 3R65,R73,R141 100

AXLE FLAME

UPRIGHT

100W-2-ND Ya geo RSF200JB-100R 5% 2W

56 5R74,R103,R109,R142,R144 10K

603 P10.0KHCT-ND Panasonic ERJ-3EKF1002V 0.01 0.1W

57 8R76,R81,R82,R104,R105, 10K

805 541-10KACT-ND Vishay/Dale CRCW080510K0JNEA 5%

0.125W

R107,R108,R151

58 1R77 100K

603 541-10KACT-ND Panasonic ERJ-3GEYJ104V 5% 0.1W DNP

59 2R79,R150 100

603 P100GCT-ND Panasonic ERJ-3GEYJ101V 5% 0.1W

60 6R89,R90,R93,R94,R95,R96 499

603 P499HCT-ND Panasonic ERJ-3EKF4990V 1% 0.1W

61 3R91,R100,R101 0

RES_TH_50 0 0.0EBK-ND Yageo ZOR-12-B-52 1% 0.1W DNP

62 6R92,R97,R98,R99,R102, 750

RES_TH_50 0 270-750-RC Xicon 270-750-RC 1% 0.1W DNP

R112

63 1R110 2K

603 P2.00KHCT-ND Panasonic ERJ-3EKF2001V 1% 0.1W

64 1R111 4.02K

603 P4.02KHCT-ND Panasonic ERJ-3EKF4021V 1% 0.1W

65 2R138,R143 10K

603 P10.0KHCT-ND Panasonic ERJ-3EKF1002V 1% 0.1W DNP

66 1R139 1.5

1206 541-1.5ECT-ND Vishay/Dale CRCW12061R50JNEA 5% 0.25W

67 3R140,R146,R147 3.4K

805 541-3.40KCCT-ND Vishay/Dale CRCW08053K40FKEA 1%

0.125W

68 1R148 820

AXLE FLAME

UPRIGHT

P820W-2BK-ND Panasonic ERG2SJ821 5% 2W

69 2R149,R152 68

1206 P68.0FTR-ND Panasonic ERJ-8ENF68R0V 1% 0.25W

70 3SW3,SW4,SW5 PB

PB P13598SCT-ND Panasonic EVQ-PNF05M

71 2TP2,TP3 TESTPOINT

TESTPOINTSMA

5011K-ND KEYSTONE 5011

72 3T4,T5,T6 750110056

XFORM/56

6543

Midcom 750110056

73 1U1 TL431

SO8-NARROW 296-1288-1-ND

Texas Instrume

TL431AIDR

74 1U2 FT232RQ

32QFNW/NO

SPT

806-KUSBVX-

BS1N-W

Kycon KUSBVX-BS1N-W

75 1U3 ADUM3201

SO8-NARROW ADUM3201ARZ-ND

Analog Devices

ADUM3201ARZ

76 1U4 SER EEPROM

SO8-NARROW AT24C1024BW-SH25-B-ND ATMEL AT24C1024BW-SH25-B

77 1U5

71M6543-100TQFP

IC149

100TQFP_SS

Teridian 71M6540F-IGT/F

78 1U6 LNK304-TN

SO8-NARROW 596-1237-1-ND

Power Integrat

LNK304DG-TL

79 1U8 LCD VLS-6648

LCD VLS-6648 VARITRONIX VL_6648_V00

80 1U9

SER EEPROM (uWi re

SO8-NARROW 93LC76C-I/SN-ND MICROCHIP 93LC76CT-I/SN

81 3U15,U16,U17 71M6103-8SOIC

SO8-NARROW Ma xi m 71M6103-IL/F

82 1Y1 32.768KHz

XTAL-ECS-39 Suntsu SPC6-32.768KHZ TR

71M6543 Demo Board User’s Manual

Page: 73 of 91 v5

4.5 71M6543 DEMO BOARD REV 5.0 BILL OF MATERIAL

Table 4-3: 71M6543 REV 5.0 Demo Board: Bill of Material (1/3)

Item QReference Part Footprint Digi-Key P/N Mous er P/N Manufacturer Manufacturer P/N Tol Rating HDR DNP

1 2 BT1 ,BT2 BATTERY

BAT 3 PIN

BARREL

COMBO

DNP

2 1 BT3 BATTERY

BAT CR2032

MAX

DNP

3 1 CN1 USB-B

USBV

806-KUSBVX-BS1

Kycon KUSBVX-BS1N-W

423 C1,C8,C9,C11,C13,C14,C15, 1000pF

603 445-1298-1-ND TDK C1608X7R2A102K 10% 100V

C29,C32,C36,C37,C38,C40,

C41,C42,C44,C49,C50,C52,C53,

C57,C61

5 1 C2 22uF

SM/CT_3216 478-1663-1-ND AVX TAJA226K010RNJ 10% 10V

618 C3,C5,C18,C19,C20,C21, 0.1uF

603 445-1314-1-ND TDK C1608X7R1H104K 0.1 50V

C22,C26,C27,C28,C51,C60,

C62,C63,C64,C66,C74,C77

7 4 C6,C7,C45,C47 10uF

SM/CT_3216 478-1654-1-ND AVX TAJA106K010R 0.1 10V

8 3 C17,C34,C56 1uF

603 445-1604-1-ND TDK C1608X7R1C105K 10% 16V DNP

9 1 C24 15pF

603 445-1271-1-ND TDK C1608C0G1H150J 5% 50V

10 1C25 10pF

603 445-1269-1-ND TDK C1608C0G1H100D 5% 50V

11 2C30,C31 22pF

603 445-1273-1-ND TDK C1608C0G1H220J 5% 50V

12 6C48,C58,C65, 1000pF

603 445-1298-1-ND TDK C1608X7R2A102K 0.1 100V DNP

C67,C68,C69

13 1C35 2.2uF

CYL/D.400/LS.

200/.034

493-1227-ND Nichicon UVR2G2R2MPD 400V

14 1C39 100uF

CYL/D.400/LS.

200/.034

P963-ND Panasonic ECE-A1AKS101 0.2 10V

15 1C46 0.03 uF

HIGH VOLT

DISC CAP

75-125LS30-R Vishay/BC 125LS30-R 1000V

16 1C54 0.1uF

603 445-1314-1-ND TDK C1608X7R1H104K 10% 50V DNP

17 2C55,C59 100pF

603 445-1281-1-ND TDK C1608C0G1H101J 5% 50V

18 2C70,C71 0.1uF

805 478-3351-1-ND

AVX Corporatio

08055C104MAT2A 0.2 50V

19 1C72 0.01uF

603 478-1227-1-ND

AVX Corporatio

06035C103KAT2A 0.1 50V

20 1C73 4.7uF

805 587-1782-1-ND Taiyo Yuden TMK212BJ475KG-T 0.1 25V

21 2D5,D6 LED_1

LED6513 67-1612-ND Lumex SSL-LX5093SRC/E

22 1D7 LD274

LED6513 475-1461-ND Osra m SFH 4511

23 4D8,D12,D13,D14 S1J

SMA/DIODE RS1J-E3/61TGICT-ND

Vishay/Genera

S1J-E3/61T

24 1D9 ES1J

SMA/DIODE ES1JFSCT-ND Vishay ES1J

25 1D10 LED

805 L62415CT-ND CML CMD17-21UGC/TR8

26 1D17 1.5KE350A

DO-41 1.5KE350CALFCT-ND Littelfuse 1.5KE350CA

27 5JP1,J1,JP3,JP44,JP45 HDR3X1

BLKCON.100/V

H/TM1SQ/W.1

00/3

S1011E-36-ND Sullins PBC36SAAN 0.1

28 1JP2 HDR5X1

BLKCON.100/V

H/TM1SQ/W.1

00/5

S1011E-36-ND Sullins PBC36SAAN 0.2

29 25 TP1,J3,JP4,JP5,JP6,JP7, HDR2X1

BLKCON.100/V

H/TM1SQ/W.1

00/2

S1011E-36-ND Sullins PBC36SAAN 0.1

JP8,J11,J12,J13,J15,J16,

J17,J18,J20,J22,J23,J24,

J25,JP50,JP51,JP52,JP53,

JP54,JP55

30 1JP20 SWITCHCRAFT

SWITCHCRAFT SC237-ND

Switchcraft Inc.

RAPC712X

31 4J4,J6,J8,J9 Spade Terminal

FASTON A24747CT-ND Tyco/AMP 62395-1

32 1J14 ICE Header

RIBBON6513O

UTLINE

A33555-ND

571-5-104068-

Tyco/AMP 5-104068-1

33 1J19 HDR5X2

BLKCON.100/V

H/TM2OE/W.2

00/10

S2011E-36-ND Sullins PBC36DAAN 0.2

34 1J21 HDR8X2

BLKCON.100/V

H/TM2OE/W.2

00/16

S2011E-36-ND Sullins PBC36DAAN 0.3

35 15 L1,L2,L3,L4,L5,L6,L7,L9,

Ferrite Bead 600oh

805 445-1556-1-ND TDK MMZ2012S601A 0.5A

L10,L11,L12,L13,L16,L17,

L18

36 1L8 180uH

RFB0807 CoilCraft RFB0807-181L

37 1Q1 BP103

LED6513 475-1437-ND Osra m SFH 300-3/4 DNP

38 3RV1,RV2,RV3 VARISTOR

MOV CPS

2381594

594-2381-594-

55116

AVX 2381 594 55116

71M6543 Demo Board User’s Manual

Page: 74 of 91 v5

Table 4-4: 71M6543 REV 5.0 Demo Board: Bill of Material (2/3)

Item QReference Part Footprint Digi-Key P/N Mous er P/N Manufacturer Manufacturer P/N Tol Rating HDR DNP

39 2R1,R2 1K

805 541-1.0KACT-ND Vishay/Dale CRCW08051K00JNEA 5%

0.125W

40 1R4 100

805 541-100ACT-ND Vishay/Dale CRCW0805100RJNEA 5%

0.125W

41 3R6,R7,R8 75K

AXLE FLAME

UPRIGHT

75KW-2-ND Yageo RSF200JB-75K 5% 2W DNP

42 6R9,R10,R11,R15,R16,R17 62

603 P62GCT-ND Panasonic ERJ-3GEYJ620V 5% 0.1W

43 2R12,R13 100K

603 P100KGCT-ND Panasonic ERJ-3GEYJ104V 0.05 0.1W

44 5R14,R33,R52,R54,R72 750

805 RR12P750DCT-ND Susumu RR1220P-751-D 0.01 0.1W

45 1R18 0

1206 RHM0.0ECT-ND

Rohm Semicond

MCR18EZHJ000 5% 0.25W

46 3R19,R106,R137 1K

603 P1.00KHCT-ND Panasonic ERJ-3EKF1001V 1% 0.1W

47 1R20 8.06K

805 RHM8.06KCCT-ND Rohm MCR10EZHF8061 1%

0.125W

48 1R21 25.5K

805 P25.5KCCT-ND Panasonic ERJ-6ENF2552V 1%

0.125W

49 12 R24,R25,R26,R27,R28,R29, 5.1

MELF

71-

SMM02040C5

108FB30

Vishay/Dale SMM02040C5108FB30 0.01

0.125W

R30,R31,R32,R34,R35,R36

50 3R38,R39,R58 4.7K

805 RG20P4.7KBCT-ND TDK RG2012P-472-B-T5 0%

0.125W

51 6R46,R47,R59,R60,R62,R64 270K

805 RG20P270KBCT-ND Susumu RG2012P-274-B-T5 0%

0.125W

52 3R61,R63,R66 2M

AXLE FLAME

UPRIGHT

71-RN65D-F-

2.0M

Vishay/Dale RN65D2004FB14 0.01 0.5W

53 3R65,R73,R141 100

AXLE FLAME

UPRIGHT

100W-2-ND Ya geo RSF200JB-100R 5% 2W

54 12 R74,R89,R90,R93,R94,R95, 10K

603 P10.0KHCT-ND Panasonic ERJ-3EKF1002V 0.01 0.1W

R96,R103,R107,R109,R142,

R144

55 7R76,R81,R82,R104,R105, 10K

805 541-10KACT-ND Vishay/Dale CRCW080510K0JNEA 5%

0.125W

R108,R151

56 1R77 100K

603 541-10KACT-ND Panasonic ERJ-3GEYJ104V 5% 0.1W DNP

57 2R79,R150 100

603 P100GCT-ND Panasonic ERJ-3GEYJ101V 5% 0.1W

58 3R91,R100,R101 0

RES_TH_50 0 0.0EBK-ND Yageo ZOR-12-B-52 1% 0.1W

59 6R92,R97,R98,R99,R102, 750

RES_TH_50 0 270-750-RC Xicon 270-750-RC 1% 0.1W

R112

60 1R110 2K

603 P2.00KHCT-ND Panasonic ERJ-3EKF2001V 1% 0.1W

61 1R111 4.02K

603 P4.02KHCT-ND Panasonic ERJ-3EKF4021V 1% 0.1W

62 2R138,R143 10K

603 P10.0KHCT-ND Panasonic ERJ-3EKF1002V 1% 0.1W DNP

63 1R139 1.5

1206 541-1.5ECT-ND Vishay/Dale CRCW12061R50JNEA 5% 0.25W

64 3R140,R146,R147 3.4K

805 541-3.40KCCT-ND Vishay/Dale CRCW08053K40FKEA 1%

0.125W

65 1R148 820

AXLE FLAME

UPRIGHT

P820W-2BK-ND Panasonic ERG2SJ821 5% 2W

66 2R149,R152 68

1206 P68.0FTR-ND Panasonic ERJ-8ENF68R0V 1% 0.25W

67 3SW3,SW4,SW5 PB

PB P13598SCT-ND Panasonic EVQ-PNF05M

68 2TP2,TP3 TESTPOINT

TESTPOINTSMA

5011K-ND KEYSTONE 5011

69 3T4,T5,T6 750110056

XFORM/56

6543

Midcom 750110056 DNP

70 1U1 TL431

SO8-NARROW 296-1288-1-ND

Texas Instrume

TL431AIDR

71 1U2 FT232RQ

32QFNW/NO

SPT

768-1008-1-ND FTDI FT232RQ-REEL

72 1U3 ADUM3201

SO8-NARROW ADUM3201ARZ-ND

Analog Devices

ADUM3201ARZ

73 1U4 SER EEPROM

SO8-NARROW AT24C1024BW-SH25-B-ND ATMEL AT24C1024BW-SH25-B

74 1U5

71M6543-100TQFP

IC149

100TQFP_SS

Teridian 71M6540F-IGT/F

75 1U6 LNK304-TN

SO8-NARROW 596-1237-1-ND

Power Integrat

LNK304DG-TL

76 1U8 LCD VLS-6648

LCD VLS-6648 VARITRONIX VL_6648_V00

77 1U9

SER EEPROM (uWi re

SO8-NARROW 93LC76C-I/SN-ND MICROCHIP 93LC76CT-I/SN

78 3U15,U16,U17 71M6103-8SOIC

SO8-NARROW Ma xi m 71M6103-IL/F DNP

79 1Y1 32.768KHz

XTAL-ECS-39 Suntsu SPC6-32.768KHZ TR

71M6543 Demo Board User’s Manual

Page: 75 of 91 v5

4.6 71M6543 REV 4.0 DEMO BOARD PCB LAYOUT

Figure 4-10: Teridian 71M6543 REV 4.0 Demo Board: Top View

71M6543 Demo Board User’s Manual

Page: 76 of 91 v5

Figure 4-11: Teridian 71M6543 REV 4.0 Demo Board: Top Copper

71M6543 Demo Board User’s Manual

Page: 77 of 91 v5

Figure 4-12: Teridian 71M6543 REV 4.0 Demo Board: Bottom View

71M6543 Demo Board User’s Manual

Page: 78 of 91 v5

Figure 4-13: Teridian 71M6543 REV 4.0 Demo Board: Bottom Copper

71M6543 Demo Board User’s Manual

Page: 79 of 91 v5

4.7 71M6543 REV 5.0 DEMO BOARD PCB LAYOUT

Figure 4-14: Teridian 71M6543 REV 5.0 Demo Board: Top View

71M6543 Demo Board User’s Manual

Page: 80 of 91 v5

Figure 4-15: Teridian 71M6543 REV 5.0 Demo Board: Top Copper

71M6543 Demo Board User’s Manual

Page: 81 of 91 v5

Figure 4-16: Teridian 71M6543 REV 5.0 Demo Board: Bottom View

71M6543 Demo Board User’s Manual

Page: 82 of 91 v5

Figure 4-17: Teridian 71M6543 REV 5.0 Demo Board: Bottom Copper

71M6543 Demo Board User’s Manual

Page: 83 of 91 v5

4.8 DEBUG BOARD BILL OF MATERIAL

Table 4-5: Debug Board: Bill of Material

Item QReference Value PCB Footprint P/N Manufacturer Vendor Vendor P/N

121 C1-C3,C5-C10,C12-C23 0.1uF 0805 C2012X7R1H104K TDK Digi-Key 445-1349-1-ND

2 1 C4 33uF/10V 1812 TAJB336K010R AVX Digi-Key 478-1687-1-ND

3 1 C11 10uF/16V, B Case 1812 TAJB106K016R AVX Digi-Key 478-1673-1-ND

4 2 D2,D3 LED 0805 LTST-C170KGKT LITEON Digi-Key 160-1414-1-ND

5 4 JP1,JP2,JP3,JP4 HDR2X1 2x1pin PZC36SAAN Sullins Digi-Key S1011-36-ND

6 1 J1 RAPC712 RAPC712 Switchcraft Digi-Key SC1152-ND

7 1 J2 DB9 DB9 A2100-ND AMP Digi-Key A2100-ND

8 1 J3 HEADER 8X2 8x2pin PPTC082LFBN Sullins Digi-Key S4208-ND

9 4 R1,R5,R7,R8 10K 0805 ERJ-6GEYJ103V Panasonic Digi-Key P10KACT-ND

10 2R2,R3 1K 0805 ERJ-6GEYJ102V Panasonic Digi-Key P1.0KACT-ND

11 1R4 NC 0805 N/A N/A N/A N/A

12 1R6 00805 ERJ-6GEY0R00V Panasonic Digi-Key P0.0ACT-ND

13 1SW2 PB Switch PB EVQ-PJX05M Panasonic Digi-Key P8051SCT-ND

14 2TP5,TP6 test point TP 5011 Keystone Digi-Key 5011K-ND

15 5U1,U2,U3,U5,U6 ADUM1100 SOIC8 ADUM1100AR ADI Digi-Key ADUM1100AR-ND

16 1U4 MAX3237CAI SOG28 MAX3237CAI MAXIM Digi-Key MAX3237CAI-ND

17 4spacer 2202K-ND Keystone Digi-Key 2202K-ND

18 44-40, 1/4" screw PMS4400-0025PH Building Fasteners Digi-Key H342-ND

19 24-40, 5/16" screw PMS4400-0031PH Building Fasteners Digi-Key H343-ND

20 24-40 nut HNZ440 Building Fasteners Digi-Key H216-ND

71M6543 Demo Board User’s Manual

Page: 84 of 91 v5

4.9 DEBUG BOARD SCHEMATICS

Figure 4-18: Debug Board: Electrical Schematic

C11

10uF, 16V (B Case)

C15

0.1uF

C13

0.1uF

VDD1 1

DIN 2

VDD1 3

GND1 4

GND2

5DOUT

6GND2

7VDD2

ADUM1100

VDD1

DIN

VDD1

GND1

4GND2 5

DOUT 6

GND2 7

VDD2 8

ADUM1100

C19

0.1uF

GND_DBG

C23

0.1uF

GND_DBG

GND

C21

0.1uF

V5_DBG

GND

V3P3

C14

0.1uF

C18

0.1uF

C17

0.1uF

GND_DBG

0.1uF

V3P3

GND

DIO02

V5_DBG

GND_DBG

0.1uF

V5_DBG

GND_DBG

DIO01

VDD1 1

DIN 2

VDD1 3

GND1 4

GND2

5DOUT

6GND2

7VDD2

ADUM1100

DIO00

GND_DBG GND

0.1uF

GND_DBG

V5_DBG DIO01_DBG

0.1uF

V3P3

0.1uF

LED

GND_DBG

DIO01

V5_DBG

GND

232VP1

R XPC

232VN1

232C1P1

232C1M1

232C2M1

10K

GND_DBG

GND

C10

0.1uF

V5_DBG

GND_DBG

GND

DIO00

VDD1 1

DIN 2

VDD1 3

GND1 4

GND2

5DOUT

6GND2

7VDD2

ADUM1100

V3P3

0.1uF

V3P3

C12

0.1uF

GND

GND_DBG

V5_DBG

LED

DIO00_DBG

GND_DBG

V5_DBG

C22

0.1uF

JP4

HDR2X1

GND_DBG

VDD1

DIN

VDD1

GND1

4GND2 5

DOUT 6

GND2 7

VDD2 8

ADUM1100

V5_DBG

GND_DBG

GND

UAR T_TX

V3P3

GND

UART_RX_T

SW2

DISPLAY SEL

C20

0.1uF

GND

V5_DBG

GND_DBG

RAPC712

C16

0.1uF

V3P3

GND

V5_DBG

GND_DBG

GND

TP6

TP5

10K

DB9_RS232

10K

5Vdc EXT SUPPLY

DEBUG CONNECTOR

STATUS LEDs

RS232 TRANSCEIVER

UART_RX

TX232

NORM A L

910

11 12

13 14

15 16

HEADER 8X2

DIO00

GND

DIO02

V5_DBG

GND_DBG

GND

CKTEST

V3P3

DIO01

UART_RX_T

UAR T_TX

TMUXOU T

V5_DBG

GND_DBG

232C2P1

NORM A L

NULL

RX232

V5_DBG

GND_DBG

TXPC

TXI SO

RXISO

+C4

33uF, 10V C7

0.1uF

JP3

HDR2X1

JP1

HDR2X1

JP2

HDR2X1

C1+ 28

C1- 25

C2+ 1

C2- 3

T1I N 24

T2I N 23

T3I N 22

T4I N 19

T5I N 17

R1OUTBF 16

R1OUT 21

R2OUT 20

R3OUT 18

GND

MBAUD

SHDNB

14 ENB

R3IN

11 R2IN

9R1IN

T1OU T

T2OU T

T3OU T

T4OU T

T5OU T

V-

V+

VCC 26

MAX3237CAI

71M6543 Demo Board User’s Manual

Page: 85 of 91 v5

4.10 OPTIONAL DEBUG BOARD PCB LAYOUT

Figure 4-19: Debug Board: Top View

Figure 4-20: Debug Board: Bottom View

71M6543 Demo Board User’s Manual

Page: 86 of 91 v5

Figure 4-21: Debug Board: Top Signal Layer

Figure 4-22: Debug Board: Middle Layer 1 (Ground Plane)

71M6543 Demo Board User’s Manual

Page: 87 of 91 v5

Figure 4-23: Debug Board: Middle Layer 2 (Supply Plane)

Figure 4-24: Debug Board: Bottom Trace Layer

71M6543 Demo Board User’s Manual

Page: 88 of 91 v5

4.11 71M6543 PIN-OUT INFORMATION

Power/Ground/NC Pins:

Table 4-6: 71M6543 Pin Description Table 1/3

Name

Type

Description

GNDA

Analog ground: This pin should be connected directly to the ground plane.

GNDD

Digital ground: This pin should be connected directly to the ground plane.

V3P3A P

Analog power supply: A 3.3 V power supply should be connected to this pin.

V3P3A must be the same voltage as V3P3SYS.

V3P3SYS P

System 3.3 V supply. This pin should be connected to a 3.3 V power supply.

V3P3D O

Auxiliary voltage output of the chip. In mission mode, this pin is connected

to V3P3SYS by the internal selection switch. In BRN mode, it is internally

connected to VBAT. V3P3D is floating in LCD and sleep mode. A bypass

capacitor to ground should not exceed 0.1 µF.

VDD O

The output of the 2.5V regulator. This pin is powered in MSN and BRN

modes. A 0.1 µF bypass capacitor to ground should be connected to this

pin.

VLCD O

The output of the LCD DAC. A 0.1 µF bypass capacitor to ground should be

connected to this pin.

VBAT P

Battery backup pin to support the battery modes (BRN, LCD). A battery or

super-capacitor is to be connected between VBAT and GNDD. If no battery

is used, connect VBAT to V3P3SYS.

VBAT_RTC P

RTC and oscillator power supply. A battery or super-capacitor is to be con-

nected between VBAT and GNDD. If no battery is used, connect

VBAT_RTC to V3P3SYS.

Analog Pins:

Table 4-7: 71M6543 Pin Description Table 2/3

Name

Type

Description

IAP/IAN,

IBP/IBN,

ICP/ICN

IDP/IDN

Differential or single-ended Line Current Sense Inputs: These pins are voltage

inputs to the internal A/D converter. Typically, they are connected to the outputs

of current sensors. Unused pins must be tied to V3P3A.

Pins IBP/IBN, ICP/ICN, and IDP/IDN may be configured for communication with

the remote sensor interface (71M6x0x).

VA, VB,

VC I

Line Voltage Sense Inputs: These pins are voltage inputs to the internal A/D

converter. Typically, they are connected to the outputs of resistor dividers. Un-

used pins must be tied to V3P3A.

VREF

Voltage Reference for the ADC. This pin should be left unconnected (floating).

XIN

XOUT

Crystal Inputs: A 32 kHz crystal should be connected across these pins. Typical-

ly, a 15 pF capacitor is also connected from XIN to GNDA and a

10 pF capacitor is connected from XOUT to GNDA. It is important to minimize

the capacitance between these pins. See the crystal manufacturer datasheet for

details.

If an external clock is used, a 150 mV (p-p) clock signal should be applied to

XIN, and XOUT should be left unconnected.

Pin types: P = Power, O = Output, I = Input, I/O = Input/Output

71M6543 Demo Board User’s Manual

Page: 89 of 91 v5

Digital Pins:

Table 4-8: 71M6543 Pin Description Table 3/3

Name

Type

Description

COM3,COM2,

COM1,COM0

LCD Common Outputs: These 4 pins provide the select signals for

the LCD display.

SEGDIO0 …

SEGDIO45 I/O

Multi-use pins, configurable as either LCD segment driver or DIO.

Alternative functions with proper selection of associated I/O RAM

registers are:

SEGDIO0 = WPULSE

SEGDIO1 = VPULSE

SEGDIO2 = SDCK

SEGDIO3 = SDATA

SEGDIO6 = XPULSE

SEGDIO7 = YPULSE

Unused pins must be configured as outputs or terminated to

V3P3/GNDD.

SEGDIO26/ COM5,

SEGDIO27/ COM4

I/O

Multi-use pins, configurable as either LCD segment driver or DIO with

alternative function (LCD common drivers).

SEGDIO36/

SPI_CSZ,

SEGDIO37/ SPI_DO,

SEGDIO38/ SPI_DI,

SEGDIO39/ SPI_CKI

I/O Multi-use pins, configurable as either LCD segment driver or DIO with

alternative function (SPI interface).

SEGDIO51/

OPT_TX,

SEGDIO55/ OPT_RX

I/O Multi-use pins, configurable as either LCD segment driver or DIO with

alternative function (optical port/UART1)

E_RXTX/SEG48

I/O Multi-use pins, configurable as either emulator port pins (when ICE_E

pulled high) or LCD segment drivers (when ICE_E tied to GND).

E_RST/SEG50

E_TCLK/SEG49

ICE_E I

ICE enable. When zero, E_RST, E_TCLK, and E_RXTX become

SEG50, SEG49, and SEG48 respectively. For production units, this

pin should be pulled to GND to disable the emulator port.

TMUXOUT/ SEG47,

TMUX2OUT/ SEG46

Multi-use pins, configurable as either multiplexer/clock output or LCD

segment driver using the I/O RAM registers.

RESET I

Chip reset: This input pin is used to reset the chip into a known state.

For normal operation, this pin is pulled low. To reset the chip, this pin

should be pulled high. This pin has an internal 30 μA (nominal) cur-

rent source pull-down. No external reset circuitry is necessary.

RX I

UART0 input. If this pin is unused it must be terminated to

V3P3D or GNDD.

UART0 output.

TEST I

Enables Production Test.

This pin must be grounded in normal operation.

PB I

Push button input. This pin must be at GNDD when not active or un-

used. A rising edge sets the IE_PB flag. It also causes the part to wake

up if it is in SLP or LCD mode. PB does not have an internal pull-up or

pull-down resistor.

N/C

Do not connect this pin.

Pin types: P = Power, O = Output, I = Input, I/O = Input/Output,

71M6543 Demo Board User’s Manual

Page: 90 of 91 v5

Figure 4-25: 71M6543, LQFP100: Pin-out (top view)

Teridian

71M6543F

71M6543H

10026

SEGDIO17

TMUXOUT/SEG47

SPI_DI/SEGDIO38

V3P3D

SEGDIO1/VPULSE

SEGDIO3/SDATA

SPI_CSZ/SEGDIO36

V3P3SYS

COM1

COM2

COM3

COM0

SEGDIO45

XIN

GNDD

VBAT

ICE_E

SEGDIO52

OPT_TX/SEGDIO51

V3P3A

GNDA

VLCD

TEST

OPT_RX/SEGDIO55

ICN

XOUT

IAP

IBN

ICP

IAN

IBP

IDP

SEGDIO27/COM4

IDN

SPI_DO/SEGDIO37

SEGDIO26/COM5

SEGDIO25

SEGDIO24

SEGDIO23

SEGDIO22

SEGDIO21

SEGDIO20

SEGDIO19

SEGDIO35

SEGDIO33

SEGDIO32

SEGDIO30

SEGDIO29

SEGDIO31

SEGDIO28

SEGDIO34

SEGDIO18

GNDA

VBAT_RTC

E_RXTX/SEG48

E_TCLK/SEG49

E_RST/SEG50

SEGDIO53

RESET

TMUX2OUT/SEG46

SEGDIO44

SEGDIO43

SEGDIO42

SEGDIO41

SEGDIO40

SPI_CKI/SEGDIO39

SEGDIO16

SEGDIO15

SEGDIO14

SEGDIO13

SEGDIO10

SEGDIO11

SEGDIO12

SEGDIO9

SEGDIO8/DI

SEGDIO7/YPULSE

SEGDIO6/XPULSE

SEGDIO5

SEGDIO4

SEGDIO2/SDCK

SEGDIO0/WPULSE

SEGDIO54

VREF

VDD

71M6543 Demo Board User’s Manual

Page: 91 of 91 v5

4.12 REVISION HISTORY

Revision

Date

Description

2.0 02-19-2010 Initial release based on DBUM revision 1.0 for 6543 REV 1.0 Demo Board.

2.1 02-23-2010 Minor corrections. Added more figures illustrating shunt arrangements.

2.2 03-01-2010

Specified type of Remote Sensor used on REV 2.0 board (71M6113 or

71M6203). Improved Table 1-9. Added description for i_max2 variable

used to control neutral current. Improved page layout.

2.3 03-04-2010 Changed type of Remote Sensor Interface from 71M6113 to 71M6103.

Updated schematics and BOM of the REV 2.0 Demo Board.

2.4 06-16-2010

Corrected “X” factor for

WRATE

calculation to 0.09375. Changed section

on shunt arrangement. Improved description on temperature compensa-

tion. Added Figure 1.7 and section 1.10.7.

2.5 06-21-2010 Added part numbers for shunt resistors.

3.0 07-26-2010

Added documentation for 6543 REV 3.0 Demo Board. Updated calibration

spread sheets.

3.1 08-10-2010

Fixed display of calibration spread sheets in PDF file. Replaced Teridian

Logo with Maxim Logo.

3.2 12-10-2010

Updated information on temperature compensation and on Demo Board

revision 3.0.

4.0 02-16-2011

Updated to match board revisions 4.0 and 5.0. Removed information on

older board revisions (3.0).

Added comments on schematics.

4.1 03-28-2011

Updated schematics and BOM for DB6543 REV5.0. Added explanation

and table of Demo Code versions.

4.2 05-06-2011

Added explanation on technique to avoid cross-talk between shunt resis-

tors.

5 7/2012

Corrected addresses for auto-calibration parameter in CLI table.

Corrected entries in table 1-11 (meter accuracy classes). Changed color

for all table headings from yellow to gray.

Corrected formula in 2.3.3.1. Removed text stating that the Demo Code

and documents/tools are delivered on a CD-ROM in the kit. Added attribute

‘optional’ for all references to the ‘Debug Board’. Added USB Interface

Module as part of Demo Kit Contents.

Added text stating that spreadsheets are available on the Maxim web site.

Updated graphs and text in Serial Connection Setup (1.7.4) and updated

Demo Code version in Compatibility (1.5).

Updated images for calibration spreadsheets and changed description of

calibration to reflect the usage of LCOMP2_n coefficients used in newer

codes.

Added section 1.10.8 (Bootloader Feature).

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Maxim Integrated:

71M6543F-DB 71M6543F-DB-CT