ACT-SF2816 High Speed 128Kx16 SRAM / 512Kx16 FLASH Multichip Module CIRCUIT TECHNOLOGY www.aeroflex.com FEATURES 2 - 128K x 8 SRAMs & 2 - 512K x 8 Flash Die in One MCM Access Times of 25ns (SRAM) and 60ns (Flash) or 35ns (SRAM) and 70 or 90ns (Flash) Organized as 128K x 16 of SRAM and 512K x 16 of Flash Memory with Separate Data Buses Both Blocks of Memory are User Configurable as 512KX8 AND 1MX8 Respectively Low Power CMOS Input and Output TTL Compatible Design MIL-PRF-38534 Compliant MCMs Available Decoupling Capacitors and Multiple Grounds for Low Noise Industrial and Military Temperature Ranges Industry Standard Pinouts 66 Pin, 1.08" x 1.08" x .160" PGA Type, No Shoulder, Aeroflex code# "P3" 66 Pin, 1.08" x 1.08" x .185" PGA Type, With Shoulder, Aeroflex code# "P7" 68 Lead, .94" x .94" x .140" Single-Cavity Small Outline Gull Wing, Aeroflex code# "F18" (Drops into the 68 Lead JEDEC .99"SQ CQFJ footprint) DESC SMD - TBD FLASH MEMORY FEATURES Sector Architecture (Each Die) 8 Equal Sectors of 64K bytes each Any combination of sectors can be erased with one command sequence Note: Programming information available upon request Packaging - Hermetic Ceramic +5V Programing, +5V Supply Embedded Erase and Program Algorithms Hardware and Software Write Protection Internal Program Control Time. 10,000 Erase / Program Cycles Block Diagram - PGA Type Packages (P3 & P7) & CQFP (F18) Pin Description SWE 1 SCE1 SWE2 SCE2 FWE1 FCE1 FWE2 FCE2 OE A0 - A18 128Kx8 SRAM 128Kx8 SRAM 512Kx8 Flash 512Kx8 Flash 8 8 8 8 SI/O0-7 SI/O8-15 FI/O0-7 FI/O8-15 FI/O0-15 Flash Data I/O SI/O0-15 SRAM Data I/O A0-18 Address Inputs FWE 1-2 Flash Write Enables SWE 1-2 SRAM Write Enables FCE1-2 Flash Chip Enables SCE1-2 SRAM Chip Enables OE Output Enable NC Not Connected VCC Power Supply GND Ground eroflex Circuit Technology - Advanced Multichip Modules (c) SCD3853 REV B 5/18/99 Absolute Maximum Ratings Symbol TC TSTG Rating Range Units Operating Temperature -55 to +125 C Storage Temperature -65 to +150 C -0.5 to +7 V 300 C VG Maximum Signal Voltage to Ground TL Maximum Lead Temperature (10 seconds) Parameter Flash Data Retention 10 Years Flash Endurance (Write/Erase Cycles) 10,000 Normal Operating Conditions Symbol Parameter Minimum Maximum Units VCC Power Supply Voltage +4.5 +5.5 V VIH Input High Voltage +2.2 VCC + 0.3 V VIL Input Low Voltage -0.5 +0.8 V Capacitance (VIN = 0V, f = 1MHz, TC = 25C) Symbol Maximum Units A0 - A18 Capacitance 50 pF OE Capacitance 50 pF CWE1,2 F/S Write Enable Capacitance 20 pF CCE1,2 F/S Chip Enable Capacitance 20 pF I/O0 - I/O15 Capacitance 20 pF Min Max Units CAD COE CI/O Parameter These parameters are guaranteed by design but not tested DC Characteristics (VCC = 5.0V, VSS = 0V, Tc = -55C to +125C, unless otherwise indicated) Parameter Sym Conditions Input Leakage Current ILI VCC = Max, VIN = 0 to VCC 10 A Output Leakage Current ILO FCE = SCE = VIH, OE = VIH, VOUT = 0 to VCC 10 A 325 mA SRAM Operating Supply Current x 16 I x16 SCE = VIL, OE = VIH, f = 5MHz, VCC = CC Max, FCE = VIH Mode Standby Current ISB FCE = SCE = VIH, OE = VIH, f = 5MHz, VCC = Max 40 mA SRAM Output Low Voltage VOL IOL = 8 mA, VCC = Min, FCE = VIH 0.4 V SRAM Output High Voltage VOH IOH = -4.0 mA, , VCC = Min, FCE = VIH Flash Vcc Active Current for Read (1) ICC1 FCE = VIL, OE = VIH, SCE = VIH 130 mA Flash Vcc Active Current for Program or Erase (2) ICC2 FCE = VIL, OE = VIH, SCE = VIH 150 mA Flash Output Low Voltage VOL IOL = 8 mA, VCC = Min, SCE = VIH 0.45 V Flash Output High Voltage VOH IOH = -2.5 mA, , VCC = Min, SCE = VIH Flash Low Vcc Lock Out Voltage VLKO 2.4 V 0.85 x VCC V 3.2 V Notes: 1) The ICC current listed includes both the DC operating current and the frequency dependent component (at 5MHz). The frequency component typically is less than 2mA/MHz, with OE at VIH 2) ICC active while Embedded Algorithim (program or erase) is in progress 3) DC test conditions: VIL = 0.3V, VIH = VCC - 0.3V Aeroflex Circuit Technology 2 SCD3853 REV B 5/18/99 Plainview NY (516) 694-6700 SRAM AC Characteristics (VCC = 5.0V, VSS= 0V, Tc= -55C to +125C) Read Cycle Parameter Symbol -025 Min Max -035 Min Max 25 35 Units ns Read Cycle Time tRC Address Access Time tAA 25 35 ns Chip Select Access Time tACE 25 35 ns Output Hold from Address Change tOH Output Enable to Output Valid tOE Chip Select to Output in Low Z * tCLZ 3 3 ns Output Enable to Output in Low Z * tOLZ 0 0 ns Chip Deselect to Output in High Z * tCHZ 12 20 ns Output Disable to Output in High Z * tOHZ 12 20 ns -025 Min Max -035 Min Max 0 0 15 ns 20 ns * Parameters guaranteed by design but not tested Write Cycle Parameter Symbol Units Write Cycle Time tWC 25 35 ns Chip Select to End of Write tCW 20 25 ns Address Valid to End of Write tAW 20 25 ns Data Valid to End of Write tDW 15 20 ns Write Pulse Width tWP 20 25 ns Address Setup Time tAS 0 0 ns Output Active from End of Write * tOW 0 0 ns Write to Output in High Z * tWHZ Data Hold from Write Time tDH 0 0 ns Address Hold Time tAH 0 0 ns 10 20 ns * Parameters guaranteed by design but not tested Truth Table Mode SCE OE SWE Data I/O Power Standby H X X High Z Standby Read L L H Data Out Active Output Disable L H H High Z Active Write L X L Data In Active Aeroflex Circuit Technology 3 SCD3853 REV B 5/18/99 Plainview NY (516) 694-6700 Timing Diagrams -- SRAM Write Cycle Timing Diagrams Read Cycle Timing Diagrams Write Cycle (SWE Controlled, OE = VIH) Read Cycle 1 (SCE = OE = VIL, SWE = VIH) tWC tRC A0-18 A0-18 tAA tAW tCW tOH DI/O Previous Data Valid tAH SCE Data Valid tAS tWP SWE tWHZ tOW tDH tDW SEE N OTE DI/O Data Valid Read Cycle 2 (SWE = VIH) tRC Write Cycle (SCE Controlled, OE = VIH ) A0-18 tWC tAA A0-18 tAH tAW SCE tAS tACE tCW tCHZ tCLZ SEE NOTE SCE tOHZ SWE SEE NOTE OE tWP tOE SEE NOTE tOLZ SEE NOTE DI/O UNDEFINED tDW Data Valid High Z DI/O tDH Data Valid Note: Guaranteed by design, but not tested. DON'T CARE AC Test Circuit Current Source AC Test Conditions IOL VZ ~ 1.5 V (Bipolar Supply) To Device Under Test CL = 50 pF Parameter Typical Units Input Pulse Level 0 - 3.0 V Input Rise and Fall 5 ns Input and Output Timing Reference Level 1.5 V IOH Current Source Notes: 1) VZ is programmable from -2V to +7V. 2) IOL and I OH programmable from 0 to 16 mA. 3) Tester Impedance ZO = 75. 4) VZ is typically the midpoint of VOH and VOL. 5) IOL and IOH are adjusted to simulate a typical resistance load circuit. 6) ATE Tester includes jig capacitance. Aeroflex Circuit Technology 4 SCD3853 REV B 5/18/99 Plainview NY (516) 694-6700 Flash AC Characteristics - Read Only Operations (Vcc = 5.0V, Vss = 0V, Tc = -55C to +125C) Symbol -60 -70 -90 Units JEDEC Stand'd Min Max Min Max Min Max Parameter Read Cycle Time tAVAV tRC 60 70 90 ns Address Access Time tAVQV tACC 60 70 90 ns Chip Enable Access Time tELQV tCE 60 70 90 ns Output Enable to Output Valid tGLQV tOE 30 35 35 ns Chip Enable to Output High Z (1) tEHQZ tDF 20 20 20 ns Output Enable High to Output High Z(1) tGHQZ tDF 20 ns Output Hold from Address, CE or OE Change, Whichever is First tAXQX tOH 20 20 0 0 0 ns Note 1. Guaranteed by design, but not tested Flash AC Characteristics - Write / Erase / Program Operations, FWE Controlled (Vcc = 5.0V, Vss = 0V, Tc = -55C to +125C) Parameter Symbol JEDEC Stand'd -60 -70 -90 Min Max Min Max Min Max Units Write Cycle Time tAVAC tWC 60 70 90 ns Chip Enable Setup Time tELWL tCE 0 0 0 ns Write Enable Pulse Width tWLWH tWP 40 45 45 ns Address Setup Time tAVWL tAS 0 0 0 ns Data Setup Time tDVWH tDS 40 45 45 ns Data Hold Time tWHDX tDH 0 0 0 ns Address Hold Time tWLAX tAH 45 45 45 ns Write Enable Pulse Width High tWHWL tWPH 20 20 20 ns Duration of Byte Programming Operation tWHWH1 Sector Erase Time tWHWH2 Read Recovery Time before Write tGHWL 14 0 tOEH 1 Chip Erase Time TYP 14 30 0 50 Chip Programming Time Chip Enable Hold Time 14 30 tVCE Vcc Setup Time TYP TYP s 30 Sec 50 s 0 50 s 50 50 50 Sec 10 10 10 ns 120 tWHWH3 120 120 Sec 1. Toggle and Data Polling only. Flash AC Characteristics - Write / Erase / Program Operations, FCE Controlled (Vcc = 5.0V, Vss = 0V, Tc = -55C to +125C) Parameter Symbol JEDEC Stand'd -60 -70 -90 Min Max Min Max Min Max Write Cycle Time tAVAC tWC Write Enable Setup Time tWLEL tWS 0 Chip Enable Pulse Width tELEH tCP 40 Address Setup Time tAVEL tAS 0 Data Setup Time tDVEH tDS 40 Data Hold Time tEHDX tDH 0 Address Hold Time tELAX tAH 45 Chip Enable Pulse Width High tEHEL tCPH 20 Duration of Byte Programming tWHWH1 Sector Erase Time tWHWH2 Read Recovery Time tGHEL Chip Programming Time Chip Erase Time Aeroflex Circuit Technology tWHWH3 5 60 14 70 90 ns 0 0 ns 45 45 ns 0 0 ns 45 45 ns 0 0 ns 45 45 ns 20 TYP 14 30 0 Units 20 TYP 14 30 0 ns TYP s 30 Sec 0 ns 50 50 50 Sec 120 120 120 Sec SCD3853 REV B 5/18/99 Plainview NY (516) 694-6700 AC Waveforms for Flash Memory Read Operations tRC Addresses Addresses Stable tACC FCE tDF OE tOE FWE tCE t OH High Z Outputs Output Valid High Z Write/Erase/Program Operation for Flash Memory, FWE Controlled Data Polling Addresses 5555H PA tWC tAS PA tRC tAH FCE tGHWL OE tWP tWHWH1 tWPH FWE tCE tDF tOE tDH AOH Data PD D7 DOUT tDS t OH 5.0V tCE Notes: 1. PA is the address of the memory location to be programmed. 2. PD is the data to be programmed at byte address. 3. D7 is the 0utput of the complement of the data written to the deviced. 4. Dout is the output of the data written to the device. 5. Figure indicates last two bus cycles of four bus cycle sequence. Aeroflex Circuit Technology 6 SCD3853 REV B 5/18/99 Plainview NY (516) 694-6700 AC Waveforms Chip/Sector Erase Operations for Flash Memory Data Polling tAH 5555H Addresses 2AAAH 5555H 5555H 2AAAH SA tAS FCE tGHWL OE tWP FWE tCE tWPH tDH AAH Data 55H 80H AAH 55H 10H/30H tDS VCC tVCE Notes: 1. SA is the sector address for sector erase. AC Waveforms for Data Polling During Embedded Algorithm Operations for Flash Memory tCH FCE tDF tOE OE tOEH tCE FWE tOH * DQ7 DQ7 DQ7= Valid Data High Z t WHWH1 or 2 DQ0-DQ6 DQ0-DQ6 Valid Data DQ0-DQ6=Invalid tOE * DQ7=Valid Data (The device has completed the Embedded operation). Aeroflex Circuit Technology 7 SCD3853 REV B 5/18/99 Plainview NY (516) 694-6700 Write/Erase/Program Operation for Flash Memory, FCE Controlled Data Polling Addresses 5555H PA tWC tAS PA t AH FCE tGHWL OE tCP FWE tWHWH1 tCPH tWS tDH AOH Data PD D7 DOUT tDS 5.0V Notes: 1. PA is the address of the memory location to be programmed. 2. PD is the data to be programmed at byte address. 3. D7 is the 0utput of the complement of the data written to the device. 4. DOUT is the output of the data written to the device. 5. Figure indicates last two bus cycles of four bus cycle sequence. Aeroflex Circuit Technology 8 SCD3853 REV B 5/18/99 Plainview NY (516) 694-6700 Pin Numbers & Functions 66 Pins -- PGA-Type Pin # Function Pin # Function Pin # Function Pin # Function 1 SI/O8 18 A12 35 FI/O9 52 FWE1 2 SI/O9 19 Vcc 36 FI/O10 53 FCE1 3 SI/O10 20 SCE1 37 A6 54 GND 4 A13 21 NC 38 A7 55 FI/O3 5 A14 22 SI/O3 39 NC 56 FI/O15 6 A15 23 SI/O15 40 A8 57 FI/O14 7 A16 24 SI/O14 41 A9 58 FI/O13 8 A17 25 SI/O13 42 FI/O0 59 FI/O12 9 SI/O0 26 SI/O12 43 FI/O1 60 A0 10 SI/O1 27 OE 44 FI/O2 61 A1 11 SI/O2 28 A18 45 VCC 62 A2 12 SWE2 29 SWE1 46 FCE2 63 FI/O7 13 SCE2 30 SI/O7 47 FWE2 64 FI/O6 14 GND 31 SI/O6 48 FI/O11 65 FI/O5 15 SI/O11 32 SI/O5 49 A3 66 FI/O4 16 A10 33 SI/O4 50 A4 17 A11 34 FI/O8 51 A5 "P3" -- 1.08" SQ PGA Type Package Standard (without shoulders) "P7" -- 1.08" SQ PGA Type Package (with shoulders on Pins 1, 11, 56 & 66) Bottom View (P7 & P3) Side View (P7) Side View (P3) 1.085 SQ MAX 1.000 TYP .600 TYP .185 MAX .025 .035 Pin 1 Pin 56 .050 DIA TYP .100 TYP .100 TYP .020 .016 .020 .016 1.000 TYP Pin 66 Pin 11 .145 MIN All dimensions in inches Aeroflex Circuit Technology .165 MIN .100 TYP .160 MAX 9 SCD3853 REV B 5/18/99 Plainview NY (516) 694-6700 Pin Numbers & Functions 68 Pins -- Dual-Cavity CQFP Pin # Function Pin # Function Pin # Function Pin # Function 1 GND 18 GND 35 OE 52 GND 2 FCE1 19 SI/O8 36 SCE2 53 FI/O7 3 A5 20 SI/O9 37 A17 54 FI/O6 4 A4 21 SI/O10 38 SWE2 55 FI/O5 5 A3 22 SI/O11 39 FWE1 56 FI/O4 6 A2 23 SI/O12 40 FWE2 57 FI/O3 7 A1 24 SI/O13 41 A18 58 FI/O2 8 A0 25 SI/O14 42 NC 59 FI/O1 9 NC 26 SI/O15 43 NC 60 FI/O0 10 SI/O0 27 Vcc 44 FI/O15 61 VCC 11 SI/O1 28 A11 45 FI/O14 62 A10 12 SI/O2 29 A12 46 FI/O13 63 A9 13 SI/O3 30 A13 47 FI/O12 64 A8 14 SI/O4 31 A14 48 FI/O11 65 A7 15 SI/O5 32 A15 49 FI/O10 66 A6 16 SI/O6 33 A16 50 FI/O9 67 SWE1 17 SI/O7 34 SCE1 51 FI/O8 68 FCE2 "F18" -- CQFP Package Pin 9 .990 SQ .010 .950 SQ MAX Pin 10 .140 MAX .015 .002 Pin 61 Pin 60 .008 .002 .010 .008 .050 REF .015 .002 .050 TYP Detail "A" .890 SQ REF .640 SQ REF Metal spacer Pin 26 Pin 27 Pin 44 .800 REF Pin 43 See Detail "A" All dimensions in inches Aeroflex Circuit Technology 10 SCD3853 REV B 5/18/99 Plainview NY (516) 694-6700 CIRCUIT TECHNOLOGY Ordering Information Model Number DESC SMD Number Speed Package ACT-SF2816N-26P3Q TBD 25(S) / 60(F) ns 1.08"sq PGA-Type ACT-SF2816N-37P3Q TBD 35(S) / 70(F) ns 1.08"sq PGA-Type ACT-SF2816N-39P3Q TBD 35(S) / 90(F) ns 1.08"sq PGA-Type ACT-SF2816N-26P7Q TBD 25(S) / 60(F) ns 1.08"sq PGA-Type ACT-SF2816N-37P7Q TBD 35(S) / 70(F) ns 1.08"sq PGA-Type ACT-SF2816N-39P7Q TBD 35(S) / 90(F) ns 1.08"sq PGA-Type ACT-SF2816N-26F18Q TBD 25(S) / 60(F) ns .94"sq CQFP ACT-SF2816N-37F18Q TBD 35(S) / 70(F) ns .94"sq CQFP ACT-SF2816N-39F18Q TBD 35(S) / 90(F) ns .94"sq CQFP Note: (S) = Speed for SRAM, (F) = Speed for FLASH Part Number Breakdown ACT- S F 28 16 N- 26 P7 Q Aeroflex Circuit Technology Screening C = Commercial Temp, 0C to +70C I = Industrial Temp, -40C to +85C T = Military Temp, -55C to +125C M = Military Temp, -55C to +125C, Screening * Q = MIL-PRF-38534 Compliant / SMD Memory Type SF = SRAM Flash Combo Module Memory Depth 2 = 2M SRAM, 8 = Locations Package Type & Size Surface Mount Packages Thru-Hole Packages F18 = .94"SQ 68 Lead Dual-Cavity P3 = 1.085"SQ PGA 66 Pins with out shoulder CQFP P7 = 1.085"SQ PGA 66 Pins with shoulder Memory Width, Bits Options, N = none Memory Speed Code 26 = 25ns SRAM & 60ns FLASH 37 = 35ns SRAM & 70ns FLASH 39 = 35ns SRAM & 90ns FLASH * Screened to the individual test methods of MIL-STD-883 Specifications subject to change without notice. Aeroflex Circuit Technology 35 South Service Road Plainview New York 11830 Aeroflex Circuit Technology Telephone: (516) 694-6700 FAX: (516) 694-6715 Toll Free Inquiries: 1-(800) 843-1553 11 SCD3853 REV B 5/18/99 Plainview NY (516) 694-6700