DESCRIPTION
Power over Ethernet (PoE) splitters can make your project wiring a breeze - and best of all they
work to connect any 802.3af-capable router to any Ethernet device,
even if it doesn't natively
support PoE!
The splitter takes a unified PoE signal (data and power) from one RJ-45 cable,
and then separates the data (Ethernet) and power (5 VDC regulated) into two different lines for
non-PoE devices.
This is an economical, practical, high-performance, and reliable Isolated 5V 2.4A PoE Splitter
with MicroUSB Plug based on IEEE 802.3af standard. It can divide power and data signals
from a network cable, and can be used with any PoE injector that is compatible with IEEE
802.3af, and supply power and data for non-PoE network equipment.
Whew, that's quite a few words - but basically: Connect this to your PoE switch or hub, then on
the other side of the Ethernet cable, you'll get Ethernet and a high quality 5V power supply, up
to 2.4 Amps.
This is perfect for use with a Raspberry Pi model B, B+, Pi 2 or Pi 3 since those have Ethernet
and micro USB power, and 2.4 Amp is
plenty
of current for even the most accessorized Pi. (It
isn't a good match for the Pi Zero or A+ because those don't have Ethernet, although you could
use an Ethernet hub.) It also works great with Arduino boards and compatibles that have
Ethernet and micro USB like the Seeed Cloud or an Arduino-compatible with an Ethernet shield
- just check that the compatible has a micro USB power input! It would also be a perfect
addition to a Feather with our Ethernet Feather attached.
Please note that like many active PoE splitters, there's a minimum load requirement of at least
100mA on the 5V power supply. We don't think this is going to be a problem since anything with
Ethernet will tend to draw 200mA+, but please keep it in mind!
For use only with true 802.3af routers! If you don't have a PoE injector / hub / router, check out
our passive PoE cable kit.
TECHNICAL DETAILS
Ethernet cable length: 205mm / 8"
New Products 6/6/2018 Featuring RFID/NFC Nail Stickers! @adafru…
MicroUSB cable length: 205mm / 8"
Body dimensions: 80mm x 30mm x 24mm / 3" x 1" x .8"
Features:
IEEE 802.3af compliant
Supports 10/100M data transmission (not for Gigabit ethernet)
Supports 48V Unsolicited Power Over Ethernet PoE Switches/Hubs/Adapters with a 44V-
57V power voltage input
Operation temperature: 20°C - 45°C
Storage temperature:- 30°C - 70°C
Isolation: 2.5kV
Power Input: 44~57V DC
Power Output: 5V DC 2.4A
Product Weight: 54.1g / 1.9oz
MAY WE ALSO SUGGEST...
Passive PoE Injector Cable
Set
Ethernet RJ45 Male Plug
Terminal Block
802.3af PoE Output Data &
Power Splitter - 5/9/12V
Ethernet Shield for Arduino
- W5500 Chipset
Cable Gland - Waterproof
RJ-45 / Ethernet connector
Ethernet Cable - 3 ft long
Ethernet RJ45 Female
Socket Push-Terminal Block
802.3af PoE Output Data &
Power Splitter - 12V 1A
Adafruit Ethernet
FeatherWing
Panel Mount Ethernet
Extension Cable
Seeeduino Cloud -
Compatible with Arduino
Ethernet Cable - 10 ft long
EXPAND TO SEE DISTRIBUTORS
DISTRIBUTORS
CONTACT
SUPPORT
DISTRIBUTORS
EDUCATORS
JOBS
FAQ
"Only knowledge that is used sticks
in your mind" -
Dale Carnegie
