W947D2HBJX5I - Winbond Electronics Corporation America

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 1 - Revision A01-003

TABLE OF CONTENTS

1. GENERAL DESCRIPTION .......................................................................................................... 4

2. FEATURES.................................................................................................................................. 4

3. PIN CONFIGURATION ................................................................................................................ 5

3.1 Ball Assignment: LPDDR X16 .......................................................................................................... 5

3.2 Ball Assignment: LPDDR X32 .......................................................................................................... 5

4. PIN DESCRIPTION ..................................................................................................................... 6

4.1 Signal Descriptions ........................................................................................................................... 6

4.2 Addressing Table ............................................................................................................................. 7

5. BLOCK DIAGRAM ...................................................................................................................... 8

5.1 Block Diagram .................................................................................................................................. 8

5.2 Simplified State Diagram .................................................................................................................. 9

6. FUNCTION DESCRIPTION ....................................................................................................... 10

6.1 Initialization .................................................................................................................................... 10

6.1.1 Initialization Flow Diagram ....................................................................................................................11

6.1.2 Initialization Waveform Sequence .........................................................................................................12

6.2 Register Definition .......................................................................................................................... 12

6.2.1 Mode Register Set Operation ................................................................................................................12

6.2.2 Mode Register Definition .......................................................................................................................13

6.2.3. Burst Length .........................................................................................................................................13

6.3 Burst Definition ............................................................................................................................... 14

6.4 Burst Type ...................................................................................................................................... 15

6.5 Read Latency ................................................................................................................................. 15

6.6 Extended Mode Register Description ............................................................................................. 15

6.6.1 Extended Mode Register Definition ......................................................................................................16

6.7 Status Register Read ..................................................................................................................... 16

6.7.1 SRR Register (A[n:0] = 0) .....................................................................................................................17

6.7.2 Status Register Read Timing Diagram .................................................................................................18

6.8 Partial Array Self Refresh ............................................................................................................... 19

6.9 Automatic Temperature Compensated Self Refresh ....................................................................... 19

6.10 Output Drive Strength ................................................................................................................... 19

6.11 Commands ................................................................................................................................... 19

6.11.1 Basic Timing Parameters for Commands ...........................................................................................19

6.11.2 Truth Table - Commands ....................................................................................................................20

6.11.3 Truth Table - DM Operations ..............................................................................................................21

6.11.4 Truth Table - CKE ...............................................................................................................................21

6.11.5 Truth Table - Current State BANKn - Command to BANKn ...............................................................22

6.11.6 Truth Table - Current State BANKn, Command to BANKn .................................................................23

7. OPERATION.............................................................................................................................. 24

7.1. Deselect ........................................................................................................................................ 24

7.2. No Operation ................................................................................................................................. 24

7.2.1 NOP Command .....................................................................................................................................25

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 2 - Revision A01-003

7.3 Mode Register Set .......................................................................................................................... 25

7.3.1 Mode Register Set Command ...............................................................................................................25

7.3.2 Mode Register Set Command Timing ...................................................................................................26

7.4. Active ............................................................................................................................................ 26

7.4.1 Active Command ...................................................................................................................................26

7.4.2 Bank Activation Command Cycle ..........................................................................................................27

7.5. Read ............................................................................................................................................. 27

7.5.1 Read Command ....................................................................................................................................28

7.5.2 Basic Read Timing Parameters ............................................................................................................28

7.5.3 Read Burst Showing CAS Latency .......................................................................................................29

7.5.4 Read to Read ........................................................................................................................................29

7.5.5 Consecutive Read Bursts ......................................................................................................................30

7.5.6 Non-Consecutive Read Bursts ..............................................................................................................30

7.5.7 Random Read Bursts ............................................................................................................................31

7.5.8 Read Burst Terminate ...........................................................................................................................31

7.5.9 Read to Write ........................................................................................................................................32

7.5.10 Read to Pre-charge .............................................................................................................................32

7.5.11 Burst Terminate of Read .....................................................................................................................33

7.6 Write ............................................................................................................................................... 33

7.6.1 Write Command ....................................................................................................................................34

7.6.2 Basic Write Timing Parameters .............................................................................................................34

7.6.3 Write Burst (min. and max. tDQSS) ......................................................................................................35

7.6.4 Write to Write .........................................................................................................................................35

7.6.5 Concatenated Write Bursts ...................................................................................................................36

7.6.6 Non-Consecutive Write Bursts ..............................................................................................................36

7.6.7 Random Write Cycles ...........................................................................................................................37

7.6.8 Write to Read ........................................................................................................................................37

7.6.9 Non-Interrupting Write to Read .............................................................................................................37

7.6.10 Interrupting Write to Read ...................................................................................................................38

7.6.11 Write to Precharge ..............................................................................................................................38

7.6.12 Non-Interrupting Write to Precharge ...................................................................................................38

7.6.13 Interrupting Write to Precharge ...........................................................................................................39

7.7 Precharge ....................................................................................................................................... 39

7.7.1 Precharge Command ............................................................................................................................40

7.8 Auto Precharge .............................................................................................................................. 40

7.9 Refresh Requirements .................................................................................................................... 40

7.10 Auto Refresh ................................................................................................................................ 40

7.10.1 Auto Refresh Command ......................................................................................................................41

7.11 Self Referesh ................................................................................................................................ 41

7.11.1 Self Refresh Command .......................................................................................................................42

7.11.2 Auto Refresh Cycles Back-to-Back .....................................................................................................42

7.11.3 Self Refresh Entry and Exit .................................................................................................................43

7.12 Power Down ................................................................................................................................. 43

7.12.1 Power-Down Entry and Exit ................................................................................................................43

7.13 Deep Power Down........................................................................................................................ 44

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 3 - Revision A01-003

7.13.1 Deep Power-Down Entry and Exit.......................................................................................................44

7.14 Clock Stop .................................................................................................................................... 45

7.14.1 Clock Stop Mode Entry and Exit .........................................................................................................45

8. ELECTRICAL CHARACTERISTIC ........................................................................................... 46

8.1 Absolute Maximum Ratings ............................................................................................................ 46

8.2 Input/Output Capacitance ............................................................................................................... 46

8.3 Electrical Characteristics and AC/DC Operating Conditions ........................................................... 47

8.3.1 Electrical Characteristics and AC/DC Operating Conditions ................................................................47

8.4 IDD Specification Parameters and Test Conditions ........................................................................ 48

8.4.1 IDD Specification Parameters and Test Conditions ..............................................................................48

8.5 AC Timings ..................................................................................................................................... 51

8.5.1 CAS Latency Definition (With CL=3) .....................................................................................................54

8.5.2 Output Slew Rate Characteristics .........................................................................................................55

8.5.3 AC Overshoot/Undershoot Specification ..............................................................................................55

8.5.4 AC Overshoot and Undershoot Definition .............................................................................................55

9. PACKAGE DIMENSIONS ......................................................................................................... 56

9.1: LPDDR X 16 .................................................................................................................................. 56

9.2: LPDDR X 32 .................................................................................................................................. 57

10. ORDERING INFORMATION ................................................................................................... 58

11. REVISION HISTORY ............................................................................................................... 59

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 4 - Revision A01-003

1. GENERAL DESCRIPTION

W947D6HB / W947D2HB is a high-speed Low Power double data rate synchronous dynamic random access

memory (LPDDR SDRAM), An access to the LPDDR SDRAM is burst oriented. Consecutive memory location in one

page can be accessed at a burst length of 2, 4, 8 and 16 when a bank and row is selected by an ACTIVE command.

Column addresses are automatically generated by the LPDDR SDRAM internal counter in burst operation. Random

column read is also possible by providing its address at each clock cycle. The multiple bank nature enables

interleaving among internal banks to hide the pre-charging time. By setting programmable Mode Registers, the

system can change burst length, latency cycle, interleave or sequential burst to maximize its performance. The

device supports special low power functions such as Partial Array Self Refresh (PASR) and Automatic Temperature

Compensated Self Refresh (ATCSR).

2. FEATURES

VDD = 1.7~1.95V

VDDQ = 1.7~1.95V;

Data width: x16 / x32

Clock rate: 200MHz(-5),166MHz(-6),133MHz(-75)

Partial Array Self-Refresh(PASR)

Auto Temperature Compensated Self-Refresh(ATCSR)

Power Down Mode

Deep Power Down Mode (DPD Mode)

Programmable output buffer driver strength

Four internal banks for concurrent operation

Data mask (DM) for write data

Clock Stop capability during idle periods

Auto Pre-charge option for each burst access

Double data rate for data output

Differential clock inputs (CK and

)

Bidirectional, data strobe (DQS)

CAS

Latency: 2 and 3

Burst Length: 2, 4, 8 and 16

Burst Type: Sequential or Interleave

64 ms Refresh period

Interface: LVCMOS compatible

Support package:

60 balls BGA (x16)

90 balls BGA (x32)

Operating Temperature Range :

Extended (-25°C ~ +85°C)

Industrial (-40°C ~ +85°C)

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 5 - Revision A01-003

3. PIN CONFIGURATION

3.1 Ball Assignment: LPDDR X16

60 BALL VFBGA

VSS

DQ15

VSSQ

VDDQ

DQ0

VDD

VDDQ

DQ13

DQ14

DQ1

DQ2

VSSQ

DQ11

DQ12

DQ3

DQ4

VDDQ

DQ9

DQ10

DQ5

DQ6

VSSQ

UDQS

DQ8

DQ7

LDQS

VDDQ

VSS

UDM

LDM

VDD

CKE

CAS

RAS

A11

BA0

BA1

A10/AP

VSS

VDD

(Top View) Pin Configuration

3.2 Ball Assignment: LPDDR X32

90 BALL VFBGA

VSS

DQ31

VSSQ

VDDQ

DQ16

VDD

VDDQ

DQ29

DQ30

DQ17

DQ18

VSSQ

DQ27

DQ28

DQ19

DQ20

VDDQ

DQ25

DQ26

DQ21

DQ22

VSSQ

DQS3

DQ24

DQ23

DQS2

VDDQ

VDD

DM3

DM2

VSS

CKE

CAS

RAS

A11

BA0

BA1

A10/AP

DM1

DM0

VSSQ

DQS1

DQ8

DQ7

DQS0

VDDQ

DQ9

DQ10

DQ5

DQ6

VSSQ

DQ11

DQ12

DQ3

DQ4

VDDQ

DQ13

DQ14

DQ1

DQ2

VSSQ

VSS

DQ15

VSSQ

VDDQ

DQ0

VDD

(Top View) Pin Configuration

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 6 - Revision A01-003

4. PIN DESCRIPTION

4.1 Signal Descriptions

SIGNAL NAME

TYPE

FUNCTION

DESCRIPTION

A [n : 0]

Input

Address

Provide the row address for ACTIVE commands, and the column

address and AUTO PRECHARGE bit for READ/WRITE

commands, to select one location out of the memory array in the

respective bank. The address inputs also provide the opcode

during a MODE REGISTER SET command.

A10 is used for Auto Pre-charge Select.

BA0, BA1

Input

Bank Select

Define to which bank an ACTIVE, READ, WRITE or

PRECHARGE command is being applied.

DQ0~DQ15 (×16)

DQ0~DQ31 (×32)

I/O

Data Input/

Output

Data bus: Input / Output.

Input

Chip Select

enables (registered LOW) and disables (registered HIGH)

the command decoder. All commands are masked when

registered HIGH.

provides for external bank selection on

systems with multiple banks.

is considered part of the

command code.

RAS

Input

Row Address

Strobe

RAS

CAS

and

(along with

) define the command

being entered.

CAS

Input

Column Address

Strobe

Referred to

RAS

Input

Write Enable

Referred to

RAS

UDM / LDM(x16);

DM0 to DM3 (x32)

Input

Input Mask

Input Data Mask: DM is an input mask signal for write data. Input

data is masked when DM is sampled HIGH along with that input

data during a WRITE access. DM is sampled on both edges of

DQS. Although DM pins are input-only, the DM loading matches

the DQ and DQS loading.

x16: LDM: DQ0 - DQ7, UDM: DQ8 – DQ15

x32: DM0: DQ0 - DQ7, DM1: DQ8 – DQ15,

DM2: DQ16 – DQ23, DM3: DQ24 – DQ31

CK /

Input

Clock Inputs

CK and

are differential clock inputs. All address and control

input signals are sampled on the crossing of the positive edge of

CK and negative edge of

.Input and output data is

referenced to the crossing of CK and

(both directions of

crossing). Internal clock signals are derived from CK/

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 7 - Revision A01-003

SIGNAL NAME

TYPE

FUNCTION

DESCRIPTION

CKE

Input

Clock Enable

CKE HIGH activates, and CKE LOW deactivates internal clock

signals, and device input buffers and output drivers. Taking CKE

LOW provides PRECHARGE, POWER DOWN and SELF

REFRESH operation (all banks idle), or ACTIVE POWER DOWN

(row ACTIVE in any bank). CKE is synchronous for all functions

except for SELF REFRESH EXIT, which is achieved

asynchronously. Input buffers, excluding CK,

and CKE, are

disabled during power down and self refresh mode which are

contrived for low standby power consumption.

LDQS, UDQS

(x16);

DQS0~DQS3

(x32)

I/O

Data Strobe

Output with read data, input with write data. Edge-aligned with

read data, centered with write data. Used to capture write data.

x16: LDQS: DQ0~DQ7; UDQS: DQ8~DQ15.

x32: DQS0: DQ0~DQ7; DQS1: DQ8~DQ15;

DQS2: DQ16~DQ23; DQS3: DQ24~DQ31.

VDD

Supply

Power

Power supply for input buffers and internal circuit.

VSS

Supply

Ground

Ground for input buffers and internal circuit.

VDDQ

Supply

Power for I/O

Buffer

Power supply separated from VDD, used for output drivers to

improve noise.

VSSQ

Supply

Ground for I/O

Buffer

Ground for output drivers.

No Connect

Non connection pin.

4.2 Addressing Table

ITEM

128Mb

Number of banks

Bank address pins

BA0,BA1

Auto precharge pin

A10/AP

X16

Row addresses

A0-A11

Column addresses

A0-A8

tREFI (µs)

15.6

x32

Row addresses

A0-A11

Column addresses

A0-A7

tREFI (µs)

15.6

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 8 - Revision A01-003

5. BLOCK DIAGRAM

5.1 Block Diagram

UDM / LDM (x16)

CKE

RAS

CAS

A10

BA0

BA1

CLOCK

BUFFER

COMMAND

DECODER

ADDRESS

BUFFER

REFRESH

COUNTER

COLUMN

COUNTER

CONTROL

SIGNAL

GENERATOR

MODE

COLUMN DECODER

SENSE AMPLIFIER

CELL ARRAY

BANK #2

COLUMN DECODER

SENSE AMPLIFIER

CELL ARRAY

BANK #0

COLUMN DECODER

SENSE AMPLIFIER

CELL ARRAY

BANK #3

DATA CONTROL

CIRCUIT

BUFFER

COLUMN DECODER

SENSE AMPLIFIER

CELL ARRAY

BANK #1

DMn

DQ0 – DQ15 (x16)

DQ0 – DQ31 (x32)

DMn (x32)

UDQS / LDQS (x16)

DQSn (x32)

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 9 - Revision A01-003

5.2 Simplified State Diagram

ACT =Active MRS =Ext . Mode Reg.

Set REFSX= Exit Self Refresh

BST = Burst Terminate MRS =Mode Register Set READ =Read w/o Auto Precharge

CKEL= Enter Power-Down PRE =Precharge READA =Read with Auto Precharge

CKEH=Exit Power - Down PREALL=Precharge All Bank WRITE = Write w/o Auto Precharge

DPDS= Enter Deep Power- Down REFA =Auto Refresh WRITEA = Write with Auto Precharge

DPDSX= Exit Deep Power- Down REFS = Enter Self Refresh

Note: Use caution with this diagram . It is indented to provide a floorplan of the possible state transitions and commands to control them,not

all details.In particular situations involving more than one bank are not captured in full detall.

Deep

Power

Down

DPDS

ACT

PRE PRE PRE

READA

READ A

Precharge

PREALL

WRITE A

PRE

WRITE READ

Burst

Stop

Row

Active

Power

Down

Precharge

Power

Down

Auto

Refresh

Idle

All banks

precharged

MRS

EMRS

Self

Refresh

Precharge

All Bank

Power

applied DPDSX

MRS REFA

REFS

REFSX

CKEL

CKEH

CKEL

WRITE

WRITEA READA

BST

READ

READA

READ

WRITE READ

WRITE

Automatic Sequence

Command Sequence

SRR

Read

SRR

SRR = Status Register Read

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 10 - Revision A01-003

6. FUNCTION DESCRIPTION

6.1 Initialization

LPDDR SDRAM must be powered up and initialized in a predefined manner. Operations procedures other than

those specified may result in undefined operation. If there is any interruption to the device power, the initialization

routine should be followed. The steps to be followed for device initialization are listed below.

The Mode Register and Extended Mode Register do not have default values. If they are not programmed during the

initialization sequence, it may lead to unspecified operation. The clock stop feature is not available until the device

has been properly initialized from Step 1 through 11.

 Step 1: Provide power, the device core power (VDD) and the device I/O power (VDDQ) must be brought up

simultaneously to prevent device latch-up. Although not required, it is recommended that VDD and VDDQ

are from the same power source. Also Assert and hold Clock Enable (CKE) to a LVCMOS logic high level

 Step 2: Once the system has established consistent device power and CKE is driven high, it is safe to apply

stable clock.

 Step 3: There must be at least 200μs of valid clocks before any command may be given to the DRAM. During this

time NOP or DESELECT commands must be issued on the command bus.

 Step 4: Issue a PRECHARGE ALL command.

 Step 5: Provide NOPs or DESELECT commands for at least tRP time.

 Step 6: Issue an AUTO REFRESH command followed by NOPs or DESELECT command for at least tRFC time.

Issue the second AUTO REFRESH command followed by NOPs or DESELECT command for at least

tRFC time. Note as part of the initialization sequence there must be two Auto Refresh commands issued.

The typical flow is to issue them at Step 6, but they may also be issued between steps 10 and 11.

 Step 7: Using the MRS command, program the base mode register. Set the desired operation modes.

 Step 8: Provide NOPs or DESELECT commands for at least tMRD time.

 Step 9: Using the MRS command, program the extended mode register for the desired operating modes. Note the

order of the base and extended mode register programmed is not important.

 Step 10: Provide NOP or DESELECT commands for at least tMRD time.

 Step 11: The DRAM has been properly initialized and is ready for any valid command.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 11 - Revision A01-003

6.1.1 Initialization Flow Diagram

1 VDD and VDDQ Ramp: CKE must be held high

2 Apply stable clocks

3 Wait at least 200us with NOP or DESELECT on command bus

4 PRECHARGE ALL

5Assert NOP or DESELCT for tRP time

6Issue two AUTO REFRESH commands each followed by

NOP or DESELECT commands for tRFC time

7 Configure Mode Register

8Assert NOP or DESELECT for tMRD time

9 Configure Extended Mode Register

10 Assert NOP or DESELECT for tMRD time

11 LPDDR SDRAM is ready for any valid command

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 12 - Revision A01-003

6.1.2 Initialization Waveform Sequence

6.2 Register Definition

6.2.1 Mode Register Set Operation

The Mode Register is used to define the specific mode of operation of the LPDDR SDRAM. This definition includes

the definition of a burst length, a burst type, a CAS latency as shown in the following figure.

The Mode Register is programmed via the MODE REGISTER SET command (with BA0=0 and BA1=0) and will

retain the stored information until it is reprogrammed, the device goes into Deep Power Down mode, or the device

loses power.

Mode Register bits A0-A2 specify the burst length, A3 the type of burst (sequential or interleave), A4-A6 the CAS

latency. A logic 0 should be programmed to all the undefined addresses bits to ensure future compatibility.

The Mode Register must be loaded when all banks are idle and no bursts are in progress, and the controller must

wait the specified time tMRD before initiating any subsequent operation. Violating either of these requirements will

result in unspecified operation.

Reserved states should not be used, as unknown operation or incompatibility with future versions may result.

VDD

VDDQ

CKE

Command

Address

A10

BA0,BA1

DQ,DQS

200us tCK tRP tRFC tRFC tMRD tMRD

NOP PRE ARF ARF MRS MRS ACT

CODE CODE

BA0=L

BA1=L BA0=L

BA1=H

All

Banks

(High-Z)

VDD/VDDQ powered up

Clock stable

Load

Mode Reg. Load

Ext.Mode Reg..

= Don't Care

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 13 - Revision A01-003

6.2.2 Mode Register Definition

A6 A5 A4

1 1

0 0

CAS Latency

Reserved

A2 A1 A0

1 1

0 0

Burst Length

Reserved

Burst Type

Sequential

Interleave

Mode Register

Address BusA0A1A2A3A4A5A6Ai..A7 (see Note 1)BA0BA1

0 0 0 (see Note 2) CAS Latency BT Burst Length

NOTE:

1.MSB depends on LPDDR SDRAM density.

2.Alogic 0 should be programmed to all unused / undefined address bits to future compatibility.

6.2.3. Burst Length

Read and write accesses to the LPDDR SDRAM are burst oriented, with the burst length and burst type being

programmable.

The burst length determines the maximum number of column locations that can be accessed for a given READ or

WRITE command. Burst lengths of 2, 4, or 8 locations are available for both the sequential and the interleaved burst

types.

When a READ or WRITE command is issued, a block of columns equal to the burst length is effectively selected. All

accesses for that burst take place within the block, meaning that the burst will wrap within the block if a boundary is

reached.

The block is uniquely selected by A1−An when the burst length is set to two, by A2−An when the burst length is set

to 4, by A3−An when the burst length is set to 8 (where An is the most significant column address bit for a given

configuration). The remaining (least significant) address bit(s) is (are) used to select the starting location within the

block. The programmed burst length applies to both read and write bursts.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 14 - Revision A01-003

6.3 Burst Definition

BURST

LENGTH

STARTING COLUMN

ADDRESS

ORDER OF ACCESSES WITHIN A BURST

(HEXADECIMAL NOTATION)

SEQUENTIAL

INTERLEAVED

0 – 1

1 – 0

0 – 1 – 2 – 3

1 – 2 – 3 – 0

1 – 0 – 3 – 2

2 – 3 – 0 – 1

3 – 0 – 1 – 2

3 – 2 – 1 – 0

0 – 1 – 2 – 3 – 4 – 5 – 6 – 7

1 – 2 – 3 – 4 – 5 – 6 – 7 – 0

1 – 0 – 3 – 2 – 5 – 4 – 7 – 6

2 – 3 – 4 – 5 – 6 – 7 – 0 – 1

2 – 3 – 0 – 1 – 6 – 7 – 4 – 5

3 – 4 – 5 – 6 – 7 – 0 – 1 – 2

3 – 2 – 1 – 0 – 7 – 6 – 5 – 4

4 – 5 – 6 – 7 – 0 – 1 – 2 – 3

5 – 6 – 7 – 0 – 1 – 2 – 3 – 4

5 – 4 – 7 – 6 – 1 – 0 – 3 – 2

6 – 7 – 0 – 1 – 2 – 3 – 4 – 5

6 – 7 – 4 – 5 – 2 – 3 – 0 – 1

7 – 0 – 1 – 2 – 3 – 4 – 5 – 6

7 – 6 – 5 – 4 – 3 – 2 – 1 – 0

0-1-2-3-4-5-6-7-8-9-A-B-C-D-E-F

1-2-3-4-5-6-7-8-9-A-B-C-D-E-F-0

1-0-3-2-5-4-7-6-9-8-B-A-D-C-F-E

2-3-4-5-6-7-8-9-A-B-C-D-E-F-0-1

2-3-0-1-6-7-4-5-A-B-8-9-E-F-C-D

3-4-5-6-7-8-9-A-B-C-D-E-F-0-1-2

3-2-1-0-7-6-5-4-B-A-9-8-F-E-D-C

4-5-6-7-8-9-A-B-C-D-E-F-0-1-2-3

4-5-6-7-0-1-2-3-C-D-E-F-8-9-A-B

5-6-7-8-9-A-B-C-D-E-F-0-1-2-3-4

5-4-7-6-1-0-3-2-D-C-F-E-9-8-B-A

6-7-8-9-A-B-C-D-E-F-0-1-2-3-4-5

6-7-4-5-2-3-0-1-E-F-C-D-A-B-8-9

7-8-9-A-B-C-D-E-F-0-1-2-3-4-5-6

7-6-5-4-3-2-1-0-F-E-D-C-B-A-9-8

8-9-A-B-C-D-E-F-0-1-2-3-4-5-6-7

9-A-B-C-D-E-F-0-1-2-3-4-5-6-7-8

9-8-B-A-D-C-F-E-1-0-3-2-5-4-7-6

A-B-C-D-E-F-0-1-2-3-4-5-6-7-8-9

A-B-8-9-E-F-C-D-2-3-0-1-6-7-4-5

B-C-D-E-F-0-1-2-3-4-5-6-7-8-9-A

B-A-9-8-F-E-D-C-3-2-1-0-7-6-5-4

C-D-E-F-0-1-2-3-4-5-6-7-8-9-A-B

C-D-E-F-8-9-A-B-4-5-6-7-0-1-2-3

D-E-F-0-1-2-3-4-5-6-7-8-9-A-B-C

D-C-F-E-9-8-B-A-5-4-7-6-1-0-3-2

E-F-0-1-2-3-4-5-6-7-8-9-A-B-C-D

E-F-C-D-A-B-8-9-6-7-4-5-2-3-0-1

F-0-1-2-3-4-5-6-7-8-9-A-B-C-D-E

F-E-D-C-B-A-9-8-7-6-5-4-3-2-1-0

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 15 - Revision A01-003

Notes:

1. For a burst length of two, A1-An selects the two data element block; A0 selects the first access within the block.

2. For a burst length of four, A2-An selects the four data element block; A0-A1 selects the first access within the block.

3. For a burst length of eight, A3-An selects the eight data element block; A0-A2 selects the first access within the block.

4. For the optional burst length of sixteen, A4-An selects the sixteen data element block; A0-A3 selects the first access within the

block.

5. Whenever a boundary of the block is reached within a given sequence, the following access wraps within the block.

When a READ or WRITE command is issued, a block of columns equal to the burst length is effectively selected. All accesses

for that burst take place within the block, meaning that the burst will wrap within the block if a boundary is reached.

The block is uniquely selected by A1-An when the burst length is set to two, by A2-An when the burst length is set to 4, by A3-

An when the burst length is set to 8 and A4-An when the burst length is set to 16(where An is the most significant column

address bit for a given configuration). The remaining (least significant) address bit(s) is (are) used to select the starting location

within the block. The programmed burst length applies to both read and write bursts.

6.4 Burst Type

Accesses within a given burst may be programmed to be either sequential or interleaved; this is referred to as the

burst type and is selected via bit A3. The ordering of accesses within a burst is determined by the burst length, the

burst type and the starting column address, as shown in the previous table.

6.5 Read Latency

The READ latency is the delay between the registration of a READ command and the availability of the first piece of

output data. The latency should be set to 2 or 3 clocks.

If a READ command is registered at a clock edge n and the latency is 3 clocks, the first data element will be valid at

n + 2 tCK + tAC. If a READ command is registered at a clock edge n and the latency is 2 clocks, the first data

element will be valid at n + tCK + tAC.

6.6 Extended Mode Register Description

The Extended Mode Register controls functions beyond those controlled by the Mode Register; these additional

functions include output drive strength selection and Partial Array Self Refresh (PASR). PASR is effective in Self

Refresh mode only.

The Extended Mode Register is programmed via the MODE REGISTER SET command (with BA1=1 and BA0=0)

and will retain the stored information until it is reprogrammed, the device is put in Deep Power Down mode, or the

device loses power.

The Extended Mode Register must be loaded when all banks are idle and no bursts are in progress, and the

controller must wait the specified time tMRD before initiating any subsequent operation. Violating either of these

requirements will result in unspecified operation.

Address bits A0-A2 specify PASR, A5-A7 the Driver Strength. A logic 0 should be programmed to all the undefined

addresses bits to ensure future compatibility.

Reserved states should not be used, as unknown operation or incompatibility with future versions may result.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 16 - Revision A01-003

6.6.1 Extended Mode Register Definition

Extended Mode Reg.

Address BusA0A1A2A3A4A5A7 ~ An....A8 (1)BA0BA1

1 0 0 ( 2) DS Reserved PASR

A6 A5 Drive Strength

Full Strength Driver

Half Strength Drive

Quarter Strength Driver

A2 A1 A0 PASR

11 1

All banks

1/2 array (BA1=0)

1/4 array (BA1=BA0=0)

Reserved

NOTES:

1.MSB depends on mobile DDR SDRAM density.

2.A logic 0 should be programmed to all unused / undefined bits to ensure future compatibility.

Octant Strength Driver

0 0 Three-Quarters Strength Driver

6.7 Status Register Read

Status Register Read (SRR) is an optional feature in JEDEC, and it is implemented in this device. With SRR, a

method is defined to read registers from the device. The encoding for an SRR command is the same as a MRS with

BA[1:0]=”01”. The address pins (A[n:0]) encode which register is to be read. Currently only one register is defined at

A[n:0]=0. The sequence to perform an SRR command is as follows:

 All reads/writes must be completed

 All banks must be closed

 MRS with BA=01 is issued (SRR)

 Wait tSRR

 Read issued to any bank/page

 CAS latency cycles later the device returns the registers data as it would a normal read

 The next command to the device can be issued tSRC after the Read command was issued.

The burst length for the SRR read is always fixed to length 2.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 17 - Revision A01-003

6.7.1 SRR Register (A[n:0] = 0)

Rising Edge of DQ Bus

SRR Register 0

Manufacturer

Identification

Revision

Identification

Refresh

Rate

Reserved(0) Density DT DW

DQ3 DQ2 DQ1 DQ0

Density

DQ13DQ14DQ15

DQ12 Device Type

Refresh RateDQ10 DQ9 DQ8

034

810

12131516X

0 0 0

1Winbond

LPDDR

Reserved

Revision ID

Device

Width

16 bits

32 bits

128

256

512

1024

2048

Reserved

0.25

Reserved

(See Note 1)

DQ7:4

DQ11

Note 2 : The refresh rate mulitiplier is based on the menory’s temperature sensor.

Note 3 : Required average periodic refresh interval = tREFI * multiplier

Note 1 : The manufacture’s revision number

starts at ‘0000’ and increments by ‘0001’ each

time a change in the manufacturer’s

specification(AC timings, or feature set), IBIS

(pull up or pull down characteristics), or

process occurs.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 18 - Revision A01-003

6.7.2 Status Register Read Timing Diagram

CMD CMD

NOP

NOPNOP

NOP MRS READ

CL=3

0 1

tRP tSRR tSRC

DQ:Reg out

=Don’t Care

PCHA, or PCH

Command

BA1,BA0

An – A0

DQS

Notes :

1. SRR can only be issued after power-up sequence is complete.

2. SRR can only be issued with all banks precharged.

3. SRR CL is unchanged from value in the mode register.

4. SRR BL is fixed at 2.

5. tSRR = 2 (min).

6. tSRC = CL + 1; (min time between read to next valid command)

7. No commands other than NOP and DES are allowed between the SRR and the READ.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 19 - Revision A01-003

6.8 Partial Array Self Refresh

With partial array self refresh (PASR), the self refresh may be restricted to a variable portion of the total array. The

whole array (default), 1/2 array, or 1/4 array could be selected. Data outside the defined area will be lost. Address

bits A0 to A2 are used to set PASR.

6.9 Automatic Temperature Compensated Self Refresh

The device has an Automatic Temperature Compensated Self Refresh feature. It automatically adjusts the refresh

rate based on the device temperature without any register update needed. To maintain backward compatibility, this

device which have Automatic TCSR, ignore (don‟t care) the inputs to address bits A3 and A4 during EMRS

programming.

6.10 Output Drive Strength

The drive strength could be set to full, half or three-quarter strength via address bits A5 and A6. The half drive

strength option is intended for lighter loads or point-to-point environments.

6.11 Commands

All commands (address and control signals) are registered on the positive edge of clock (crossing of CK going high

and

going low).

6.11.1 Basic Timing Parameters for Commands

Input Valid Valid Valid

tCLtCHtCK

tIS tIH

: Don't Care

NOTE: Input=A0 – An, BA0, BA1, CKE, CS, RAS, CAS, WE;

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 20 - Revision A01-003

6.11.2 Truth Table - Commands

NAME (FUNCTION)

RAS

CAS

A10/AP

ADDR

NOTES

DESELECT (NOP)

NO OPERATION (NOP)

ACTIVE (Select Bank and activate row)

Valid

Row

READ (Select bank and column and start read burst)

Valid

Col

READ with AP (Read Burst with Auto Precharge)

Valid

Col

WRITE (Select bank and column and start write burst)

Valid

Col

WRITE with AP (Write Burst with Auto Precharge)

Valid

Col

BURST TERMINATE or enter DEEP POWER DOWN

4, 5

PRECHARGE (Deactivate Row in selected bank)

Valid

PRECHARGE ALL (Deactivate rows in all banks)

AUTO REFRESH or enter SELF REFRESH

7, 8, 9

MODE REGISTER SET

Valid

Op-code

Notes:

1. All states and sequences not shown are illegal or reserved.

2. DESELECT and NOP are functionally interchangeable.

3. Auto precharge is non-persistent. A10 High enables Auto precharge, while A10 Low disables Auto precharge.

4. Burst Terminate applies to only Read bursts with Autoprecharge disabled. This command is undefined and should not be

used for Read with Auto precharge enabled, and for Write bursts.

5. This command is BURST TERMINATE if CKE is High and DEEP POWER DOWN entry if CKE is Low.

6. If A10 is low, bank address determines which bank is to be precharged. If A10 is high, all banks are precharged and

BA0~BA1 are don‟t care.

7. This command is AUTO REFRESH if CKE is High and SELF REFRESH if CKE is low.

8. All address inputs and I/O are „don‟t care‟ except for CKE. Internal refresh counters control bank and row addressing.

9. All banks must be precharged before issuing an AUTO-REFRESH or SELF REFRESH command.

10. BA0 and BA1 value select between MRS and EMRS.

11. CKE is HIGH for all commands shown except SELF REFRESH and DEEP POWER-DOWN.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 21 - Revision A01-003

6.11.3 Truth Table - DM Operations

FUNCTION

NOTES

Write Enable

Valid

Write Inhibit

Notes:

1. Used to mask write data, provided coincident with the corresponding data.

6.11.4 Truth Table - CKE

CKEn-1

CKEn

CURRENT STATE

COMMANDn

ACTIONn

NOTES

Power Down

Maintain Power Down

Self Refresh

Maintain Self Refresh

Deep Power Down

Maintain Deep Power Down

Power Down

NOP or DESELECT

Exit Power Down

5, 6, 9

Self Refresh

NOP or DESELECT

Exit Self Refresh

5, 7, 10

Deep Power Down

NOP or DESELECT

Exit Deep Power Down

5, 8

All Banks Idle

NOP or DESELECT

Precharge Power Down Entry

Bank(s) Active

NOP or DESELECT

Active Power Down Entry

All Banks Idle

AUTO REFRESH

Self Refresh Entry

All Banks Idle

BURST TERMINATE

Enter Deep Power Down

See the other Truth Tables

Notes:

1. CKEn is the logic state of CKE at clock edge n; CKEn-1 was the state of CKE at the previous clock edge.

2. Current state is the state of LPDDR immediately prior to clock edge n.

3. COMMANDn is the command registered at clock edge n, and ACTIONn is the result of COMMANDn.

4. All states and sequences not shown are illegal or reserved.

5. DESELECT and NOP are functionally interchangeable.

6. Power Down exit time (tXP) should elapse before a command other than NOP or DESELECT is issued.

7. SELF REFRESH exit time (tXSR) should elapse before a command other than NOP or DESELECT is issued.

8. The Deep Power-Down exit procedure must be followed as discussed in the Deep Power-Down section of the Functional

Description.

9. The clock must toggle at least once during the tXP period.

10. The clock must toggle at least once during the tXSR time.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 22 - Revision A01-003

6.11.5 Truth Table - Current State BANKn - Command to BANKn

CURRENT STATE

RAS

CAS

COMMAND

ACTION

NOTES

Any

DESELECT

NOP or Continue previous operation

No Operation

NOP or Continue previous operation

Idle

ACTIVE

Select and activate row

AUTO REFRESH

Auto refresh

MRS

Mode register set

Row Active

READ

Select column & start read burst

WRITE

Select column & start write burst

PRECHARGE

Deactivate row in bank (or banks)

Read (Auto precharge

Disabled)

READ

Select column & start new read burst

5, 6

WRITE

Select column & start write burst

5, 6, 13

PRECHARGE

Truncate read burst, start precharge

BURST

TERMINATE

Burst terminate

Write (Auto precharge

Disabled)

READ

Select column & start read burst

5, 6, 12

WRITE

Select column & start new write burst

5, 6

PRECHARGE

Truncate write burst & start precharge

Notes:

1. The table applies when both CKEn-1 and CKEn are HIGH, and after tXSR or tXP has been met if the previous state was

Self Refresh or Power Down.

2. DESELECT and NOP are functionally interchangeable.

3. All states and sequences not shown are illegal or reserved.

4. This command may or may not be bank specific. If all banks are being precharged, they must be in a valid state for

precharging.

5. A command other than NOP should not be issued to the same bank while a READ or WRITE burst with Auto Precharge is

enabled.

6. The new Read or Write command could be Auto Prechrge enabled or Auto Precharge disabled.

7. Current State Definitions:

Idle: The bank has been precharged, and tRP has been met.

Row Active: A row in the bank has been activated, and tRCD has been met. No data bursts/accesses and no register

accesses are in progress.

Read: A READ burst has been initiated, with Auto Precharge disabled, and has not yet terminated or been terminated.

Write: A WRITE burst has been initiated, with Auto Precharge disabled, and has not yet terminated or been terminated.

8. The following states must not be interrupted by a command issued to the same bank. DESEDECT or NOP commands or

allowable commands to the other bank should be issued on any clock edge occurring during these states. Allowable

commands to the other bank are determined by its current state and this table, and according to next table.

Precharging: Starts with the registration of a PRECHARGE command and ends when tRP is met. Once tRP is met, the

bank will be in the idle state.

Row Activating: Starts with registration of an ACTIVE command and ends when tRCD is met. Once tRCD is met, the bank

will be in the „row active‟ state.

Read with AP Enabled: Starts with the registration of the READ command with Auto Precharge enabled and ends when tRP

has been met. Once tRP has been met, the bank will be in the idle state.

Write with AP Enabled: Starts with registration of a WRITE command with Auto Precharge enabled and ends when tRP has

been met. Once tRP is met, the bank will be in the idle state.

9. The following states must not be interrupted by any executable command; DESEDECT or NOP commands must be applied

to each positive clock edge during these states.

Refreshing: Starts with registration of an AUTO REFRESH command and ends when tRFC is met. Once tRFC is met, the

LPDDR will be in an „all banks idle‟ state.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 23 - Revision A01-003

Accessing Mode Register: Starts with registration of a MODE REGISTER SET command and ends when tMRD has been

met. Once tMRD is met, the LPDDR will be in an „all banks idle‟ state.

Precharging All: Starts with the registration of a PRECHARGE ALL command and ends when tRP is met. Once tRP is met,

the bank will be in the idle state.

10. Not bank-specific; requires that all banks are idle and no bursts are in progress.

11. Not bank-specific. BURST TERMINATE affects the most recent READ burst, regardless of bank.

12. Requires appropriate DM masking.

13. A WRITE command may be applied after the completion of the READ burst; otherwise, a BURST TERMINATE must be

used to end the READ prior to asserting a WRITE command.

6.11.6 Truth Table - Current State BANKn, Command to BANKn

CURRENT

STATE

RAS

CAS

COMMAND

ACTION

NOTES

Any

DESELECT

NOP or Continue previous Operation

NOP

NOP or Continue previous Operation

Idle

ANY

Any command allowed to bank m

Row Activating,

Active, or

Precharging

ACTIVE

Select and activate row

READ

Select column & start read burst

WRITE

Select column & start write burst

PRECHARGE

Precharge

Read with Auto

Precharge

disabled

ACTIVE

Select and activate row

READ

Select column & start new read burst

WRITE

Select column & start write burst

8,10

PRECHARGE

Precharge

Write with Auto

Precharge

disabled

ACTIVE

Select and activate row

READ

Select column & start read burst

8, 9

WRITE

Select column & start new write burst

PRECHARGE

Precharge

Read with Auto

Precharge

ACTIVE

Select and activate row

READ

Select column & start new read burst

5, 8

WRITE

Select column & start write burst

5, 8, 10

PRECHARGE

Precharge

Write with Auto

Precharge

ACTIVE

Select and activate row

READ

Select column & start read burst

5, 8

WRITE

Select column & start new write burst

5, 8

PRECHARGE

Precharge

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 24 - Revision A01-003

Notes:

1. The table applies when both CKEn-1 and CKEn are HIGH, and after tXSR or tXP has been met if the previous state was

Self Refresh or Power Down.

2. DESELECT and NOP are functionally interchangeable.

3. All states and sequences not shown are illegal or reserved.

4. Current State Definitions:

Idle: The bank has been precharged, and tRP has been met.

Row Active: A row in the bank has been activated, and tRCD has been met. No data bursts/accesses and no register

accesses are in progress.

Read: A READ burst has been initiated, with Auto Precharge disabled, and has not yet terminated or been terminated.

Write: A Write burst has been initiated, with Auto Precharge disabled, and has not yet terminated or been terminated.

5. Read with AP enabled and Write with AP enabled: The read with Auto Precharge enabled or Write with Auto Precharge

enabled states can be broken into two parts: the access period and the precharge period. For Read with AP, the precharge

period is defined as if the same burst was executed with Auto Precharge disabled and then followed with the earliest

possible PRECHARGE command that still accesses all the data in the burst. For Write with Auto precharge, the precharge

period begins when tWR ends, with tWR measured as if Auto Precharge was disabled. The access period starts with

registration of the command and ends where the precharge period (or tRP) begins. During the precharge period, of the

Read with Auto Precharge enabled or Write with Auto Precharge enabled states, ACTIVE, PRECHARGE, READ, and

WRITE commands to the other bank may be applied; during the access period, only ACTIVE and PRECHARGE commands

to the other banks may be applied. In either case, all other related limitations apply (e.g. contention between READ data

and WRITE data must be avoided).

6. AUTO REFRESH, SELF REFRESH, and MODE REGISTER SET commands may only be issued when all bank are idle.

7. A BURST TERMINATE command cannot be issued to another bank; it applies to the bank represented by the current state

only.

8. READs or WRITEs listed in the Command column include READs and WRITEs with Auto Precharge enabled and READs

and WRITEs with Auto Precharge disabled.

9. Requires appropriate DM masking.

10. A WRITE command may be applied after the completion of data output, otherwise a BURST TERMINATE command must

be issued to end the READ prior to asserting a WRITE command.

7. OPERATION

7.1. Deselect

The DESELECT function (

= high) prevents new commands from being executed by the LPDDR SDRAM. The

LPDDR SDRAM is effectively deselected. Operations already in progress are not affected.

7.2. No Operation

The NO OPERATION (NOP) command is used to perform a NOP to a LPDDR SDRAM that is selected (

=Low).

This prevents unwanted commands from being registered during idle or wait states. Operations already in progress

are not affected.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 25 - Revision A01-003

7.2.1 NOP Command

= Don't Care

(High)

CKE

RAS

CAS

A0-An

BA0,BA1

7.3 Mode Register Set

The Mode Register and the Extended Mode Register are loaded via the address inputs. The MODE REGISTER SET

command can only be issued when all banks are idle and no bursts are in progress, and a subsequent executable

command cannot be issued until tMRD is met.

7.3.1 Mode Register Set Command

= Don't Care

(High)

CKE

RAS

CAS

A0-An

BA0,BA1

Code

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 26 - Revision A01-003

7.3.2 Mode Register Set Command Timing

Command MRS

: Don't Care

NOTE:Code=Mode Register / Extended Mode Register selection

(BA0,BA1)and op-code (A0-An)

Code Valid

ValidNOP

tMRD

Address

7.4. Active

Before any READ or WRITE commands can be issued to a bank in the LPDDR SDRAM, a row in that bank must be

opened. This is accomplished by the ACTIVE command: BA0 and BA1 select the bank, and the address inputs

select the row to be activated. More than one bank can be active at any time.

Once a row is open, a READ or WRITE command could be issued to that row, subject to the tRCD specification.

A subsequent ACTIVE command to another row in the same bank can only be issued after the previous row has

been closed. The minimum time interval between two successive ACTIVE commands on the same bank is defined

by tRC.

7.4.1 Active Command

= Don't Care

(High)

CKE

RAS

CAS

A0-An

BA0,BA1

BA=BANK Address, RA=Row

Address

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 27 - Revision A01-003

A subsequent ACTIVE command to another bank can be issued while the first bank is being accessed, which results

in a reduction of total row-access overhead. The minimum time interval between two successive ACTIVE commands

on different banks is defined by tRRD.

The row remains active until a PRECHARGE command (or READ or WRITE command with Auto Precharge) is

issued to the bank.

A PRECHARGE (or READ with Auto Precharge or Write with Auto Precharge) command must be issued before

opening a different row in the same bank.

7.4.2 Bank Activation Command Cycle

NOPNOPNOPACT ACT NOP RD/WR

Row Row Col

BA x BA y BA y

tRCDtRRD

= Don't Care

Command

A0-An

BA0,BA1

7.5. Read

The READ command is used to initiate a burst read access to an active row, with a burst length as set in the Mode

determines whether or not Auto Pre-charge is used. If Auto Pre-charge is selected, the row being accessed will be

pre-charged at the end of the read burst; if Auto Pre-charge is not selected, the row will remain open for subsequent

accesses.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 28 - Revision A01-003

7.5.1 Read Command

= Don't Care

(High)

CKE

RAS

CAS

A0-An CA

BA=BANK Address CA=Coulmn Address AP=Auto

Precharge

BABA0,BA1

A10

Enable AP

Disable AP

The basic Read timing parameters for DQs are shown in following figure; they apply to all Read operations.

7.5.2 Basic Read Timing Parameters

tDQSQmax

tAC

tLZ tQH tQH

tHZ

DO n+3DO n+2DO n+1DO n

tRPRE tRPST

tDQSCKtDQSCK

tDQSQmax

tAC

tLZ tQH tQH

tHZ

DO n+3DO n+2DO n+1DO n

tRPRE tRPST

tDQSCK

= Don,t Care

1)DO n=Data Out from column n

2)All DQ are vaild tAC after the CK edge.

All DQ are valid tDQSQ after the DQS edge, regardless of tAC

DQS

tCK

tACmax

tACmin

tCK tCH tCL

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 29 - Revision A01-003

During Read bursts, DQS is driven by the LPDDR SDRAM along with the output data. The initial Low state of the

DQS is known as the read preamble; the Low state coincident with last data-out element is known as the read post-

amble. The first data-out element is edge aligned with the first rising edge of DQS and the successive data-out

elements are edge aligned to successive edges of DQS. This is shown in following figure with a CAS latency of 2

and 3.

Upon completion of a read burst, assuming no other READ command has been initiated, the DQs will go to High-Z.

7.5.3 Read Burst Showing CAS Latency

CL=2

DO n

= Don't Care

BA Col n

READ NOP NOP NOP NOP NOP

Command

Address

DQS

1)DO n=Data Out from column n

2)BA,Col n =Bank A,Column n

3)Burst Length=4;3 subsequent elements of Data Out appear inthe programmed order following DO n

4)Shown with nominal tAC, tDQSCK and tDQSQ

CL=3

7.5.4 Read to Read

Data from a read burst may be concatenated or truncated by a subsequent READ command. The first data from the

new burst follows either the last element of a completed burst or the last desired element of a longer burst that is

being truncated. The new READ command should be issued X cycles after the first READ command, where X

equals the number of desired data-out element pairs (pairs are required by the 2n-prefetch architecture). This is

shown in following figure.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 30 - Revision A01-003

7.5.5 Consecutive Read Bursts

CL=2

DO n

= Don't Care

BA,Coln

READ NOP READ NOP NOP NOP

Command

Address

DQS

1) DO n (or b)=Data Out from column n (or column b)

2) Burst Length=4,8 or 16 (if 4, the bursts are concatenated; if 8 or 16, the second burst interrupts the first)

3) Read bursts are to an active row in the bank

4) Shown with nominal tAC, tDQSCK and tDQSQ

BA,Colb

CL=3

DO b

7.5.6 Non-Consecutive Read Bursts

A READ command can be initiated on any clock cycle following a previous READ command. Non-consecutive

Reads are shown in following figure.

CL=2

DO n

= Don't Care

BA,Col n

READ NOP NOP READ NOP NOP

Command

Address

DQS

1) DO n (or b) =Data Out from column n (or column b)

2) BA,Col n (b) =Bank A,Column n (b)

3) Burst Length=4; 3 subsequent elements of Data Out appear in the programmed order following DO n (b)

4) Shown with nominal tAC, tDQSCK and tDQSQ

DO b

CL=3

BA,Col b

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 31 - Revision A01-003

7.5.7 Random Read Bursts

Full-speed random read accesses within a page or pages can be performed as shown in following figure.

CL=2

DO n

= Don't Care

BA,Col n

READ READ NOP NOP

Command

Address

DQS

1) DO n ,etc. = Data Out from column n, etc.

nI, xI, etc. = Data Out elements, according to the programmed burst order

2) BA, Col n = Bank A, Column n

3) Burst Length=2,4,8 or 16 in cases shown (if burst of 4,8 or 16, the burst is interrupted)

4) Reads are to active rows in any banks

BA,Col b

CL=3

BA,Col x

READ READ

BA,Col g

DO nIDO xI

DO x DO b DO gDO bIDO gI

DO bI

DO bDO xI

DO xDO nI

7.5.8 Read Burst Terminate

Data from any READ burst may be truncated with a BURST TERMINATE command, as shown in figure. The

BURST TERMINATE latency is equal to the read (CAS) latency, i.e., the BURST TERMINATE command should be

issued X cycles after the READ command where X equals the desired data-out element pairs.

CL=2

= Don't Care

BA,Col n

READ NOP NOP

Command

Address

DQS

1) DO n = Data Out from column n

2) BA,Col n = Bank A, Column n

3) Cases shown are bursts of 4,8 or 16 terminated after 2 data elements.

4) Shown with nominal tAC, tDQSCK and tDQSQ

CL=3

BST NOPNOP

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 32 - Revision A01-003

7.5.9 Read to Write

Data from READ burst must be completed or truncated before a subsequent WRITE command can be issued. If

truncation is necessary, the BURST TERMINATE command must be used, as shown in following figure for the case

of nominal tDQSS

CL=2

BA,Col n

READ NOP NOP

Command

Address

DQS

1) DO n = Data Out from column n; DI b= Data In to column b

2) Burst length = 4, 8 or 16 in the cases shown; If the burst length is 2, the BST command can be omitted

3) Shown with nominal tAC, tDQSCK and tDQSQ

BST WRITENOP

= Don't Care

BA,Col n

READ WRITE NOPBST NOPNOP

BA,Col b

tDQSS

DO n

CL=3

DQS

DO n

Command

Address

7.5.10 Read to Pre-charge

A Read burst may be followed by or truncated with a PRECHARGE command to the same bank (provided Auto Pre-

charge was not activated). The PRECHARGE command should be issued X cycles after the READ command,

where X equal the number of desired data-out element pairs. This is shown in following figure. Following the

PRECHARGE command, a subsequent command to the same bank cannot be issued until tRP is met. Note that part

of the row pre-charge time is hidden during the access of the last data-out elements.

In the case of a Read being executed to completion, a PRECHARGE command issued at the optimum time (as

described above) provides the same operation that would result from Read burst with Auto Pre-charge enabled. The

disadvantage of the PRECHARGE command is that it requires that the command and address buses be available at

the appropriate time to issue the command. The advantage of the PRECHARGE command is that it can be used to

truncate bursts.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 33 - Revision A01-003

1) DO n=Data Out from column n

2) Cases shown are either uninterrupted of 4, or interrupted bursts of 8 or 16

3) Shown with nominal tAC,tDQSCK and tDQSQ

4) Precharge may be applied at (BL/2) tCK after the READ command.

5) Note that Precharge may not be issued before tRAS ns after the ACTIVE command for applicable banks.

6) The ACTIVE command may be applied if tRC has been met.

CL=2

DO n

= Don't Care

BA,Col n

READ NOP PRE NOP NOP NOP

Command

Address

DQS

CL=3

Bank

(a or all) BA,Row

tRP

7.5.11 Burst Terminate of Read

The BURST TERMINATE command is used to truncate read bursts (with Auto Pre-charge disabled). The most

recently registered READ command prior to the BURST TERMINATE command will be truncated. Note that the

BURST TERMINATE command is not bank specific.

This command should not be used to terminate write bursts.

(High)

CKE

RAS

CAS

A0-An

BA0,BA1

= Don't Care

7.6 Write

The WRITE command is used to initiate a burst write access to an active row, with a burst length as set in the Mode

determines whether or not Auto Pre-charge is used. If Auto Pre-charge is selected, the row being accessed will be

pre-charged at the end of the write burst; if Auto Pre-charge is not selected, the row will remain open for subsequent

accesses.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 34 - Revision A01-003

7.6.1 Write Command

= Don't Care

(High)

CKE

RAS

CAS

A0-An CA

BA=BANK Address

CA=Coulmn Address

AP=Auto Precharge

BA0,BA1

A10

Enable AP

Disable AP

7.6.2 Basic Write Timing Parameters

Basic Write timing parameters for DQs are shown in figure below; they apply to all Write operations.

Input data appearing on the data bus, is written to the memory array subject to the DM input logic level appearing

coincident with the data. If a given DM signal is registered Low, the corresponding data will be written to the

memory; if the DM signal is registered High, the corresponding data inputs will be ignored, and a write will not be

executed to that byte / column location.

tCK tCH tCL

tDSH

tDQSH

tDQSS

tWPRES

tWPRE

tDS

tDH tDQSL

tWPST

DQS

DQ, DM

Case 1:

tDQSS =

min

Case 2:

tDQSS =

max

tDH

tDS

tWPRES

tWPRE

tDQSH

tDQSS

tDSS

tDQSL

tDSS

tWPST

= Don't Care

1) DI n=Data In for column n

2) 3 subsequent elements of Data In are applied in the programmed order following DI n.

3) tDQSS: each rising edge of DQS must fall within the +/-25% window of the corresponding positive

clock edge.

DQ, DM

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 35 - Revision A01-003

7.6.3 Write Burst (min. and max. tDQSS)

During Write bursts, the first valid data-in element will be registered on the first rising edge of DQS following the

WRITE command, and the subsequent data elements will be registered on successive edges of DQS. The Low state

of DQS between the WRITE command and the first rising edge is called the write preamble, and the Low state on

DQS following the last data-in element is called the write post-amble.

The time between the WRITE command and the first corresponding rising edge of DQS (tDQSS) is specified with a

relatively wide range - from 75% to 125% of a clock cycle. Following figure shows the two extremes of tDQSS for a

burst of 4, upon completion of a burst, assuming no other commands have been initiated, the DQs will remain high-Z

and any additional input data will be ignored.

BA,Col b

WRITE NOP NOP

Command

Address

1) DI b = Data In to column b.

2) 3 subsequent elements of Data In are applied i nthe programmed order following DI b.

3) A non-interrupted burst of 4 is shown.

4) A10 is LOW with the WRITE command (Auto Precharge is disabled)

NOP NOPNOP

= Don't Care

DQS

tDQSSmin

tDQSSmax

7.6.4 Write to Write

Data for any WRITE burst may be concatenated with or truncated with a subsequent WRITE command. In either

case, a continuous flow of input data, can be maintained. The new WRITE command can be issued on any positive

edge of the clock following the previous WRITE command.

The first data-in element from the new burst is applied after either the last element of a completed burst or the last

desired data element of a longer burst which is being truncated. The new WRITE command should be issued X

cycles after the first WRITE command, where X equals the number of desired data-in element pairs.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 36 - Revision A01-003

7.6.5 Concatenated Write Bursts

An example of concatenated write bursts is shown in figure below.

BA,Col b

WRITE NOP NOP

Command

Address

1) DI b (n)= Data in to column b (column n)

2)3 subsequent elements of Data In are applied in the programmed order following DI b.

3 subsequent elements of Data In are applied in the programmed order following DI n.

3) Non-interrupted bursts of 4 are shown.

4) Each WRITE command may be to any active bank

NOP NOPWRITE

= Don't Care

DQS

tDQSSmin

BA,Col n

tDQSSmax

DI b

DI n

7.6.6 Non-Consecutive Write Bursts

An example of non-consecutive write bursts is shown in figure below.

BA,Col nBA,Col b

WRITE NOP NOP

Command

Address

1) Dl b (n)= Data in to column b (or column n)

2) 3 subsequent elements of Data In are applied in the programmed order following DI b.

3 subsequent elements of Data In are applied in the programmed order following DI n.

3) Non-interrupted bursts of 4 are shown.

4) Each WRITE command may be to any active bank and may be to the same or different devices.

NOP NOP WRITE

= Don't Care

DQS

tDQSSmax

BA,Col n

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 37 - Revision A01-003

7.6.7 Random Write Cycles

Full-speed random write accesses within a page or pages can be performed as shown in figure below.

BA,Col nBA,Col b

WRITE WRITE NOP

Command

Address

1) Dl b etc.= Data in to column b, etc.;

b’, etc.= the next Data In following Dl b, etc. according to the programmed burst order

2) Programmed burst length = 2, 4, 8 or 16 in cases shown. If burst of 4,8 or 16, burst would be truncated

3) Each WRITE command may be to any active bank and may be to the same or different devices.

WRITE WRITE WRITE

= Don't Care

DQS

tDQSSmax

BA,Col aBA,Col x BA,Col n BA,Col g

Di b Di b’Di x Di x’Di n Di n’Di a Di a’

7.6.8 Write to Read

Data for any Write burst may be followed by a subsequent READ command.

7.6.9 Non-Interrupting Write to Read

To follow a Write without truncating the write burst, tWTR should be met as shown in the figure below.

BA,Col b

WRITE NOP NOP

Command

Address

1) Dl b = Data in to column b

3 subsequent elements of Data In are applied in the programmed order following DI b.

2) A non-interrupted burst of 4 is shown.

3) tWTR is referenced from the positive clock edge after the last Data In pair.

4) A10 is LOW with the WRITE command (Auto Precharge is disabled)

5) The READ and WRITE commands are to the same device but not necessarily to the same bank.

NOP NOP READ

= Don't Care

DQS

tDQSSmax

BA,Col n

tWTR CL=3

DI b

NOP

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 38 - Revision A01-003

7.6.10 Interrupting Write to Read

Data for any Write burst may be truncated by a subsequent READ command as shown in the figure below. Note that

the only data-in pairs that are registered prior to the tWTR period are written to the internal array, and any subsequent

data-in must be masked with DM.

BA,Col nBA,Col b

WRITE NOP NOP

Command

Address

1) Dl b = Data in to column b. DO n=Data out from column n.

2) An interrupted burst of 4 is shown, 2 data elements are written.

3 subsequent elements of Data In are applied in the programmed order following DI b.

3) tWTR is referenced from the positive clock edge after the last Data In pair.

4)A10 is LOW with the WRITE command (Auto Precharge is disabled)

5) The READ and WRITE commands are to the same device but not necessarily to the same bank.

NOP NOP READ

= Don't Care

DQS

tDQSSmax

BA,Col n

tWTR CL=3

DI b DO n

NOP

7.6.11 Write to Precharge

Data for any WRITE burst may be followed by a subsequent PRECHARGE command to the same bank (provided

Auto Precharge was not activated). To follow a WRITE without truncating the WRITE burst, tWR should be met as

shown in the figure below.

7.6.12 Non-Interrupting Write to Precharge

BA,Col nBA,Col b

WRITE NOP PRE

Command

Address

1) Dl b = Data in to column b

3 subsequent elements of Data In are applied in the programmed order following DI b.

2) A non-interrupted burst of 4 is shown.

3) tWR is referenced from the positive clock edge after the last Data In pair.

4) A10 is LOW with the WRITE command (Auto Precharge is disabled)

NOP NOP NOP

= Don't Care

DQS

tDQSSmax

BA a (or all)

tWR

DI b

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 39 - Revision A01-003

7.6.13 Interrupting Write to Precharge

Data for any WRITE burst may be truncated by a subsequent PRECHARGE command as shown in figure below.

Note that only data-in pairs that are registered prior to the tWR period are written to the internal array, and any

subsequent data-in should be masked with DM, as shown in figure. Following the PRECHARGE command, a

subsequent command to the same bank cannot be issued until tRP is met.

BA,Col n BA a(or

all)

BA,Col b

WRITE PRE NOP

Command

Address

1) Dl b = Data in to column b.

2) An interrupted burst of 4, 8 or 16 is shown, 2 data elements are written.

3) tWR is referenced from the positive clock edge after the last desired Data In pair.

4) A10 is LOW with the WRITE command (Auto Precharge is disabled)

5) *1=can be Don't Care for programmed burst length of 4

6) *2=for programmed burst length of 4, DQS becomes Don't Care at this point

NOP NOP NOP

= Don't Care

DQS

tDQSSmax tWR

DI b

*1*1*1*1

7.7 Precharge

The PRECHARGE command is used to deactivate the open row in a particular bank or the open row in all banks.

The bank(s) will be available for a subsequent row access a specified time (tRP) after the PRECHARGE command is

issued.

Input A10 determines whether one or all banks are to be precharged. In case where only one bank is to be

precharged, inputs BA0, BA1 select the bank. Otherwise BA0, BA1 are treated as “Don‟t Care”.

Once a bank has been precharged, it is in the idle state and must be activated prior to any READ or WRITE

command being issued. A PRECHARGE command will be treated as a NOP if there is no open row in that bank, or

if the previously open row is already in the process of precharging.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 40 - Revision A01-003

7.7.1 Precharge Command

= Don't Care

(High)

CKE

RAS

CAS

Address

BA=BANK Address

(if A10 = L,otherwise Don't Care)

BABA0,BA1

A10

All Banks

One Bank

7.8 Auto Precharge

Auto Precharge is a feature which performs the same individual bank precharge function as described above, but

without requiring an explicit command. This is accomplished by using A10 (A10 = High), to enable Auto Precharge in

conjunction with a specific READ or WRITE command. A precharge of the bank / row that is addressed with the

READ or WRITE command is automatically performed upon completion of the read or write burst. Auto Precharge is

non persistent in that it is either enabled or disabled for each individual READ or WRITE command.

Auto Precharge ensures that a precharge is initiated at the earliest valid stage within a burst. The user must not

issue another command to the same bank until the precharing time (tRP) is completed. This is determined as if an

explicit PRECHARGE command was issued at the earliest possible time, as described for each burst type in the

Operation section of this specification.

7.9 Refresh Requirements

LPDDR SDRAM devices require a refresh of all rows in any rolling 64ms interval. Each refresh is generated in one of

two ways: by an explicit AUTO REFRESH command, or by an internally timed event in SELF REFRESH mode.

Dividing the number of device rows into the rolling 64ms interval defines the average refresh interval (tREFI), which is

a guideline to controllers for distributed refresh timing.

7.10 Auto Refresh

AUTO REFRESH command is used during normal operation of the LPDDR SDRAM. This command is non

persistent, so it must be issued each time a refresh is required.

The refresh addressing is generated by the internal refresh controller. The LPDDR SDRAM requires AUTO

REFRESH commands at an average periodic interval of tREFI.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 41 - Revision A01-003

7.10.1 Auto Refresh Command

= Don't Care

(High)

CKE

RAS

CAS

A0-An

BA0,BA1

7.11 Self Referesh

The SELF REFRESH command can be used to retain data in the LPDDR SDRAM, even if the rest of the system is

powered down. When in the Self Refresh mode, the LPDDR SDRAM retains data without external clocking. The

LPDDR SDRAM device has a built-in timer to accommodate Self Refresh operation. The SELF REFRESH command

is initiated like an AUTO REFRESH command except CKE is LOW. Input signals except CKE are “Don‟t Care”

during Self Refresh. The user may halt the external clock one clock after the SELF REFRESH command is

registered.

Once the command is registered, CKE must be held low to keep the device in Self Refresh mode. The clock is

internally disabled during Self Refresh operation to save power. The minimum time that the device must remain in

Self Refresh mode is tRFC.

The procedure for exiting Self Refresh requires a sequence of commands. First, the clock must be stable prior to

CKE going back High. Once Self Refresh Exit is registered, a delay of at least tXS must be satisfied before a valid

command can be issued to the device to allow for completion of any internal refresh in progress.

The use of Self Refresh mode introduces the possibility that an internally timed refresh event can be missed when

CKE is raised for exit from Self Refresh mode. Upon exit from Self Refresh an extra AUTO REFRESH command is

recommended.

In the Self Refresh mode, one additional power-saving option exist: Partial Array Self Refresh (PASR); It is

described in the Extended Mode Register section.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 42 - Revision A01-003

7.11.1 Self Refresh Command

= Don't Care

CKE

RAS

CAS

A0-An

BA0,BA1

7.11.2 Auto Refresh Cycles Back-to-Back

PRE NOP ARF NOP NOP NOPARF NOP ACT

Ba,A

Row n

Row nPre All

High-z

Command

Address

A10 (AP)

tRP tRFC tRFC

= Don't Care

Ba A, Row n = Bank A, Row n

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 43 - Revision A01-003

7.11.3 Self Refresh Entry and Exit

PRE NOP ARF NOP ARF

NOP

Pre All

High-z

Command

A10 (AP)

tRP > t RFC tRFC

= Don't Care

Address

NOP

tXSR

Any Command

(Auto Refresh

Recommene

Exit from

Self Refresh

Mode

Enter

Self Refresh

Mode

CKE

ACT

NOP

Ba, A

Row n

7.12 Power Down

Power-down is entered when CKE is registered Low (no accesses can be in progress). If power-down occurs when

all banks are idle, this mode is referred to as precharge power-down; if power-down occurs when there is a row

active in any bank, this mode is referred to as active power-down.

Entering power-down deactivates the input and output buffers, excluding CK,

and CKE. In power-down mode,

CKE Low must be maintained, and all other input signals are “Don‟t Care”. The minimum power-down duration is

specified by tCKE. However, power-down duration is limited by the refresh requirements of the device.

The power-down state is synchronously exited when CKE is registered High (along with a NOP or DESELECT

command). A valid command may be applied tXP after exit from power-down.

For Clock Stop during Power-Down mode, please refer to the Clock Stop subsection in this specification.

7.12.1 Power-Down Entry and Exit

PRE NOP NOP NOP NOP Valid

Pre All

High-z

Command

A10 (AP)

tRP tCKE tXP

Address

NOP

Any CommandExit from

Power Down

Entry

Valid

Precharge Power-Down mode shown; all banks are idle and tRP

is met when Power-down Entry command is issued = Don't Care

CKE

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 44 - Revision A01-003

7.13 Deep Power Down

The Deep Power-Down (DPD) mode enables very low standby currents. All internal voltage generators inside the

LPDDR SDRAM are stopped and all memory data is lost in this mode. All the information in the Mode Register and

the Extended Mode Register is lost.

Deep Power-Down is entered using the BURST TERMINATE command except that CKE is registered Low. All

banks must be in idle state with no activity on the data bus prior to entering the DPD mode. While in this state, CKE

must be held in a constant Low state.

To exit the DPD mode, CKE is taken high after the clock is stable and NOP commands must be maintained for at

least 200μs. After 200μs a complete re-initialization is required following steps 4 through 11 as defined for the

initialization sequence.

7.13.1 Deep Power-Down Entry and Exit

tRP T=200us

Exit DPD

Mode

Enter DPD

Mode

= Don't Care

1) Clock must be stable before exiting Deep Power-Down mode. That is, the clock must be cycling

within specifications by Ta0

2) Device must be in the all banks idle state prior to entering Deep Power-Down mode

3) 200us is required before any command can be applied upon exiting Deep-Down mode

4) Upon exiting Deep Power-Down mode a PRECHARGE ALL command must be issued, followed

by two REFRESH commands and a load mode register sequence

NOP DPD NOP Valid

Valid

Ta2Ta1Ta0T0 T1

CKE

Command

Address

DQS

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 45 - Revision A01-003

7.14 Clock Stop

Stopping a clock during idle periods is an effective method of reducing power consumption.

The LPDDR SDRAM supports clock stop under the following conditions:

 the last command (ACTIVE, READ, WRITE, PRECHARGE, AUTO REFRESH or MODE REGISTER SET) has

executed to completion, including any data-out during read bursts; the number of clock pulses per access

command depends on the device‟s AC timing parameters and the clock frequency;

 the related timing conditions (tRCD, tWR, tRP, tRFC, tMRD) has been met;

 CKE is held High

When all conditions have been met, the device is either in “idle state” or “row active state” and clock stop mode

may be entered with CK held Low and

held High.

Clock stop mode is exited by restarting the clock. At least one NOP command has to be issued before the next

access command may be applied. Additional clock pulses might be required depending on the system

characteristics.

The following Figure shows clock stop mode entry and exit.

 Initially the device is in clock stop mode

 The clock is restarted with the rising edge of T0 and a NOP on the command inputs

 With T1 a valid access command is latched; this command is followed by NOP commands in order to allow for

clock stop as soon as this access command is completed

 Tn is the last clock pulse required by the access command latched with T1

 The clock can be stopped after Tn

7.14.1 Clock Stop Mode Entry and Exit

Valid

NOP CMD NOP NOP NOP

TnT2T1T0

CKE

Command

DQ,DQS

Timing

Condition

(High-Z)

= Don't Care

Enter Clock

Stop Mode

Valid

Command

Exit Clock

Stop

Mode

Clock

Stopped

Address

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 46 - Revision A01-003

8. ELECTRICAL CHARACTERISTIC

8.1 Absolute Maximum Ratings

PARAMETER

SYMBOL

VALUES

UNITS

MIN

MAX

Voltage on VDD relative to VSS

VDD

−0.3

2.7

Voltage on VDDQ relative to VSS

VDDQ

−0.3

2.7

Voltage on any pin relative to VSS

VIN, VOUT

−0.3

2.7

Operating Case Temperature

−25

-40

°C

Storage Temperature

TSTG

−55

150

°C

Short Circuit Output Current

IOUT

±50

Power Dissipation

1.0

8.2 Input/Output Capacitance

[Notes 1-3]

PARAMETER

SYMBOL

MIN

MAX

UNITS

NOTES

Input capacitance, CK,

CCK

1.5

3.0

Input capacitance delta, CK,

CDCK

0.25

Input capacitance, all other input-only pins

1.5

3.0

Input capacitance delta, all other input-only pins

CDI

0.5

Input/ output capacitance, DQ,DM,DQS

CIO

3.0

5.0

Input/output capacitance delta, DQ, DM, DQS

CDIO

0.50

Notes:

1. These values are guaranteed by design and are tested on a sample base only.

2. These capacitance values are for single monolithic devices only. Multiple die packages will have parallel capacitive loads.

3. Although DM is an input-only pin, the input capacitance of this pin must model the input capacitance of the DQ and DQS pins. This is

required to match signal propagation times of DQ, DQS and DM in the system.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 47 - Revision A01-003

8.3 Electrical Characteristics and AC/DC Operating Conditions

All values are recommended operating conditions unless otherwise noted.

8.3.1 Electrical Characteristics and AC/DC Operating Conditions

PARAMETER/CONDITION

SYMBOL

MIN

MAX

UNITS

NOTES

Supply Voltage

VDD

1.70

1.95

I/O Supply Voltage

VDDQ

1.70

1.95

ADDRESS AND COMMAND INPUTS (A0~An, BA0,BA1,CKE,

RAS

CAS

)

Input High Voltage

VIH

0.8*VDDQ

VDDQ + 0.3

Input Low Voltage

VIL

−0.3

0.2*VDDQ

CLOCK INPUTS (CK,

)

DC Input Voltage

VIN

−0.3

VDDQ + 0.3

DC Input Differential Voltage

VID (DC)

0.4*VDDQ

VDDQ + 0.6

AC Input Differential Voltage

VID (AC)

0.6*VDDQ

VDDQ + 0.6

AC Differential Crossing Voltage

VIX

0.4*VDDQ

0.6*VDDQ

DATA INPUTS (DQ, DM, DQS)

DC Input High Voltage

VIHD (DC)

0.7*VDDQ

VDDQ + 0.3

DC Input Low Voltage

VILD (DC)

−0.3

0.3*VDDQ

AC Input High Voltage

VIHD (AC)

0.8*VDDQ

VDDQ + 0.3

AC Input Low Voltage

VILD (AC)

−0.3

0.2*VDDQ

DATA OUTPUTS (DQ, DQS)

DC Output High Voltage (IOH=−0.1mA)

VOH

0.9*VDDQ

DC Output Low Voltage (IOL=0.1mA)

VOL

0.1*VDDQ

Leakage Current

Input Leakage Current

IiL

-1

Output Leakage Current

IoL

-5

Notes:

1. All voltages referenced to VSS and VSSQ must be same potential.

2. VID (DC) and VID (AC) are the magnitude of the difference between the input level on CK and

3. The value of VIX is expected to be 0.5*VDDQ and must track variations in the DC level of the same.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 48 - Revision A01-003

8.4 IDD Specification Parameters and Test Conditions

8.4.1 IDD Specification Parameters and Test Conditions

[Recommended Operating Conditions; Notes 1-3]

(128Mb, X16)

PARAMETER

SYMBOL

TEST CONDITION

- 5

- 6

- 75

UNIT

Operating one

bank active-

precharge

current

IDD0

tRC = tRCmin ; tCK = tCKmin ; CKE is HIGH;

is HIGH between

valid commands; address inputs are SWITCHING; data bus inputs are

STABLE

Precharge

power-down

standby current

IDD2P

all banks idle, CKE is LOW;

is HIGH, tCK = tCKmin ;

address and control inputs are SWITCHING; data bus inputs

are STABLE

Low

power

0.23

Normal

power

0.28

Precharge

power-down

standby current

with clock stop

IDD2PS

all banks idle, CKE is LOW;

is HIGH, CK = LOW,

= HIGH; address and control inputs are SWITCHING; data

bus inputs are STABLE

Low

power

0.23

Normal

power

0.28

Precharge non

power-down

standby current

IDD2N

all banks idle, CKE is HIGH;

is HIGH, tCK = tCKmin; address and

control inputs are SWITCHING; data bus inputs are STABLE

Precharge non

power-down

standby current

with clock stop

IDD2NS

all banks idle, CKE is HIGH;

is HIGH, CK = LOW, = HIGH;

address and control inputs are SWITCHING; data bus inputs are

STABLE

Active power-

down standby

current

IDD3P

one bank active, CKE is LOW;

is HIGH, tCK = tCKmin;address

and control inputs are SWITCHING; data bus inputs are STABLE

Active power-

down standby

current with clock

stop

IDD3PS

one bank active, CKE is LOW;

is HIGH, CK = LOW, =

HIGH; address and control inputs are SWITCHING; data bus inputs are

STABLE

Active non

power-down

standby current

IDD3N

one bank active, CKE is HIGH;

is HIGH, tCK = tCKmin; address

and control inputs are SWITCHING; data bus inputs are STABLE

Active non

power-down

standby current

with clock stop

IDD3NS

one bank active, CKE is HIGH;

is HIGH, CK = LOW, =

HIGH; address and control inputs are SWITCHING; data bus inputs are

STABLE

Operating burst

read current

IDD4R

one bank active; BL = 4; CL = 3; tCK = tCKmin ; continuous read bursts;

IOUT = 0 mA; address inputs are SWITCHING; 50% data change each

burst transfer

Operating burst

write current

IDD4W

one bank active; BL = 4; t CK = t CKmin ; continuous write

bursts; address inputs are SWITCHING; 50% data change

each burst transfer

Auto-Refresh

Current

IDD5

tRC = tRFCmin ; tCK = tCKmin ; burst refresh; CKE is

HIGH; address and control inputs are SWITCHING; data bus inputs are

STABLE

Deep Power-

Down current

IDD8(4)

Address and control inputs are STABLE; data bus inputs are STABLE

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 49 - Revision A01-003

(128Mb, X32)

PARAMETER

SYMBOL

TEST CONDITION

- 5

- 6

- 75

UNIT

Operating one

bank active-

precharge current

IDD0

tRC = tRCmin ; tCK = tCKmin ; CKE is HIGH;

is HIGH between valid

commands; address inputs are SWITCHING; data bus inputs are

STABLE

Precharge power-

down standby

current

IDD2P

all banks idle, CKE is LOW;

is HIGH, tCK = tCKmin ;

address and control inputs are SWITCHING; data bus inputs

are STABLE

Low

power

0.23

Normal

power

0.28

Precharge power-

down standby

current with clock

stop

IDD2PS

all banks idle, CKE is LOW;

is HIGH, CK = LOW,

= HIGH; address and control inputs are SWITCHING;

data bus inputs are STABLE

Low

power

0.23

Normal

power

0.28

Precharge non

power-down

standby current

IDD2N

all banks idle, CKE is HIGH;

is HIGH, tCK = tCKmin; address and

control inputs are SWITCHING; data bus

inputs are STABLE

Precharge non

power-down

standby current

with clock stop

IDD2NS

all banks idle, CKE is HIGH;

is HIGH, CK = LOW,

= HIGH; address and control inputs are SWITCHING; data bus

inputs are STABLE

Active power-

down standby

current

IDD3P

one bank active, CKE is LOW;

is HIGH, tCK = tCKmin; address

and control inputs are SWITCHING; data bus inputs are STABLE

Active power-

down standby

current with clock

stop

IDD3PS

one bank active, CKE is LOW;

is HIGH, CK = LOW, = HIGH;

address and control inputs are SWITCHING; data bus inputs are

STABLE

Active non

power-down

standby current

IDD3N

one bank active, CKE is HIGH;

is HIGH, tCK = tCKmin; address

and control inputs are SWITCHING; data bus inputs are STABLE

Active non

power-down

standby current

with clock stop

IDD3NS

one bank active, CKE is HIGH;

is HIGH, CK = LOW, =

HIGH; address and control inputs are SWITCHING; data bus inputs are

STABLE

Operating burst

read current

IDD4R

one bank active; BL = 4; CL = 3; tCK = tCKmin ; continuous read bursts;

IOUT = 0 mA; address inputs are SWITCHING; 50% data change each

burst transfer

Operating burst

write current

IDD4W

one bank active; BL = 4; t CK = t CKmin ; continuous write

bursts; address inputs are SWITCHING; 50% data change

each burst transfer

Auto-Refresh

Current

IDD5

tRC = tRFCmin ; tCK = tCKmin ; burst refresh; CKE is

HIGH; address and control inputs are SWITCHING; data bus inputs are

STABLE

Deep Power-

Down current

IDD8(4)

Address and control inputs are STABLE; data bus inputs are STABLE

Notes:

1. IDD specifications are tested after the device is properly initialized.

2. Input slew rate is 1V/ns.

3. Definitions for IDD:

LOW is defined as VIN ≤ 0.1 * VDDQ;HIGH is defined as VIN ≥ 0.9 * VDDQ;STABLE is defined as inputs stable at a HIGH or LOW level;

SWITCHING is defined as:

- Address and command: inputs changing between HIGH and LOW once per two clock cycles;

- Data bus inputs: DQ changing between HIGH and LOW once per clock cycle; DM and DQS are STABLE.

4. IDD8 are typical value at 25℃.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 50 - Revision A01-003

IDD6 Conditions :

IDD6

Low Power

Normal Power

Units

ATCSR Range

45℃

85℃

45℃

85℃

Full Array

180

230

220

280

1/2 Array

160

200

190

250

1/4 Array

150

180

170

230

Notes:

1. Measured with outputs open.

2. IDD6 is typical value..

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 51 - Revision A01-003

8.5 AC Timings

[Recommended Operating Conditions: Notes 1-9]

PARAMETER

SYMBOL

- 5

- 6

- 75

UNIT

NOTES

MIN

MAX

MIN

MAX

MIN

MAX

DQ output access time

from CK/

CL=3

tAC

2.0

5.0

2.0

5.0

2.0

6.0

CL=2

2.0

6.5

2.0

6.5

2.0

6.5

DQS output access time from CK/

CL=3

tDQSCK

2.0

5.0

2.0

5.0

2.0

6.0

CL=2

2.0

6.5

2.0

6.5

2.0

6.5

Clock high-level width

tCH

0.45

0.55

0.45

0.55

0.45

0.55

tCK

Clock low-level width

tCL

0.45

0.55

0.45

0.55

0.45

0.55

tCK

Clock half period

tHP

Min

(tCL, tCH)

Min

(tCL, tCH)

Min

(tCL, tCH)

10,11

Clock cycle time

CL=3

tCK

7.5

CL=2

DQ and DM input setup

time

fast

tDS

0.48

0.6

0.8

13,14,15

slow

0.58

0.7

0.9

13,14,16

DQ and DM input hold time

fast

tDH

0.48

0.6

0.8

13,14,15

slow

0.58

0.7

0.9

13,14,16

DQ and DM input pulse width

tDIPW

1.6

1.8

Address and control input

setup time

fast

tIS

0.9

1.1

1.3

15,18

slow

1.1

1.3

1.5

16,18

Address and control input

hold time

fast

tIH

0.9

1.1

1.3

15,18

slow

1.1

1.3

1.5

16,18

Address and control input pulse width

tIPW

2.3

2.6

DQ & DQS low-impedance time from

CK/

tLZ

1.0

DQ & DQS high-impedance

time from CK/

CL=3

tHZ

5.0

6.0

CL=2

6.5

DQS-DQ skew

tDQSQ

0.4

0.5

0.6

DQ/DQS output hold time from DQS

tQH

tHP-tQHS

Data hold skew factor

tQHS

0.5

0.65

0.75

Write command to 1st DQS latching

transition

tDQSS

0.75

1.25

0.75

1.25

0.75

1.25

tCK

DQS input high-level width

tDQSH

0.4

0.6

0.4

0.6

0.4

0.6

tCK

DQS input low-level width

tDQSL

0.4

0.6

0.4

0.6

0.4

0.6

tCK

DQS falling edge to CK setup time

tDSS

0.2

tCK

DQS falling edge hold time from CK

tDSH

0.2

tCK

MODE REGISTER SET command

tMRD

tCK

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 52 - Revision A01-003

PARAMETER

SYMBOL

- 5

- 6

- 75

UNIT

NOTES

MIN

MAX

MIN

MAX

MIN

MAX

period

Write preamble setup time

tWPRES

Write postamble

tWPST

0.4

0.6

0.4

0.6

0.4

0.6

tCK

Write preamble

tWPRE

0.25

tCK

Read preamble

CL = 3

tRPRE

0.9

1.1

0.9

1.1

0.9

1.1

tCK

CL = 2

0.5

1.1

0.5

1.1

0.5

1.1

tCK

Read postamble

tRPST

0.4

0.6

0.4

0.6

0.4

0.6

tCK

ACTIVE to PRECHARGE command

period

tRAS

70,000

ACTIVE to ACTIVE command period

tRC

tRAS+

tRP

tRAS+

tRP

tRAS+

tRP

AUTO REFRESH to ACTIVE/AUTO

REFRESH command period

tRFC

ACTIVE to READ or WRITE delay

tRCD

22.5

PRECHARGE command period

tRP

tCK

ACTIVE bank A to ACTIVE bank B

delay

tRRD

WRITE recovery time

tWR

Auto precharge write recovery +

precharge time

tDAL

tCK

Internal write to Read command delay

tWTR

tCK

Self Refresh exit to next valid command

delay

tXSR

120

Exit power down to next valid command

delay

tXP

tCK

CKE min. pulse width (high and low

pulse width)

tCKE

tCK

Refresh Period

tREF

Average periodic refresh interval

tREFI

15.6

μs

MRS for SRR to READ

tSRR

tCK

READ of SRR to next valid command

tSRC

CL+1

tCK

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 53 - Revision A01-003

Notes:

1. All voltages referenced to VSS.

2. All parameters assume proper device initialization.

3. Tests for AC timing may be conducted at nominal supply voltage levels, but the related specifications and

device operation are guaranteed for the full voltage and temperature range specified.

4. The circuit shown below represents the timing reference load used in defining the relevant timing parameters

of the part. It is not intended to be either a precise representation of the typical system environment nor a

depiction of the actual load presented by a production tester. System designers will use IBIS or other

simulation tools to correlate the timing reference load to system environment. Manufacturers will correlate to

their production test conditions (generally a coaxial transmission line terminated at the tester electronics). For

the half strength driver with a nominal 10pF load parameters tAC and tQH are expected to be in the same

range. However, these parameters are not subject to production test but are estimated by design /

characterization. Use of IBIS or other simulation tools for system design validation is suggested.

Time Reference Load

I/O

Z0 = 50 Ohms 20pF

5. The CK/

input reference voltage level (for timing referenced to CK/

) is the point at which CK and

cross; the input reference voltage level for signals other than CK/

is VDDQ/2.

6. The timing reference voltage level is VDDQ/2.

7. AC and DC input and output voltage levels are defined in the section for Electrical Characteristics and AC/DC

operating conditions.

8. A CK/

differential slew rate of 2.0 V/ns is assumed for all parameters.

CAS

latency definition: with CL = 3 the first data element is valid at (2 * tCK + tAC) after the clock at which

the READ command was registered; with CL = 2 the first data element is valid at (tCK + tAC) after the clock at

which the READ command was registered

10. Min (tCL, tCH) refers to the smaller of the actual clock low time and the actual clock high time as provided to

the device (i.e. this value can be greater than the minimum specification limits of tCL and tCH)

11. tQH = tHP - tQHS, where tHP = minimum half clock period for any given cycle and is defined by clock high or

clock low (tCL, tCH). tQHS accounts for 1) the pulse duration distortion of on-chip clock circuits; and 2) the

worst case push-out of DQS on one transition followed by the worst case pull-in of DQ on the next transition,

both of which are, separately, due to data pin skew and output pattern effects, and p-channel to n-channel

variation of the output drivers.

12. The only time that the clock frequency is allowed to change is during clock stop, power-down or self-refresh

modes.

13. The transition time for DQ, DM and DQS inputs is measured between VIL(DC) to VIH(AC) for rising input

signals, and VIH(DC) to VIL(AC) for falling input signals.

14. DQS, DM and DQ input slew rate is specified to prevent double clocking of data and preserve setup and hold

times. Signal transitions through the DC region must be monotonic.

15. Input slew rate ≥ 1.0 V/ns.

16. Input slew rate ≥ 0.5 V/ns and < 1.0 V/ns.

17. These parameters guarantee device timing but they are not necessarily tested on each device.

18. The transition time for address and command inputs is measured between VIH and VIL.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 54 - Revision A01-003

19. tHZ and tLZ transitions occur in the same access time windows as valid data transitions. These parameters

are not referred to a specific voltage level, but specify when the device is no longer driving (HZ), or begins

driving (LZ).

20. tDQSQ consists of data pin skew and output pattern effects, and p-channel to n-channel variation of the

output drivers for any given cycle.

21. The specific requirement is that DQS be valid (HIGH, LOW, or some point on a valid transition) on or before

the corresponding CK edge. A valid transition is defined as monotonic and meeting the input slew rate

specifications of the device. When no writes were previously in progress on the bus, DQS will be transitioning

from Hi-Z to logic LOW. If a previous write was in progress, DQS could be HIGH, LOW, or transitioning from

HIGH to LOW at this time, depending on tDQSS.

22. The maximum limit for this parameter is not a device limit. The device operates with a greater value for this

parameter, but system performance (bus turnaround) will degrade accordingly.

23. A low level on DQS may be maintained during High-Z states (DQS drivers disabled) by adding a weak pull-

down element in the system. It is recommended to turn off the weak pull-down element during read and write

bursts (DQS drivers enabled).

24. At least one clock cycle is required during tWR time when in auto precharge mode.

25. tDAL = (tWR/tCK) + (tRP/tCK): for each of the terms, if not already an integer, round to the next higher

integer.

26. There must be at least two clock pulses during the tXSR period.

27. There must be at least one clock pulse during the tXP period.

28. A maximum of 8 Refresh commands can be posted to any given LPDDR SDRAM, meaning that the maximum

absolute interval between any Refresh command and the next Refresh command is 8*tREFI.

8.5.1 CAS Latency Definition (With CL=3)

CL=3

tLZmin

tRPRE

tDQSCKmin tDQSCKmin

tRPST

T5nT5T4nT3nT2n T4T3T2

READ NOP NOP NOP NOP NOPNOPCommand

DQS

All DQ,

collectively

1)DQ transitioning after DQS transition define tDQSQ window.

2)ALL DQ must transition by tDQSQ after DQS transitions, regardless of tAC

3)tAC is the DQ output window relative to CK,and is the long term component of DQ skew.

T0 T1 T2 T2n T3 T3n T4 T4n T5 T5n T6

tLZmin

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 55 - Revision A01-003

8.5.2 Output Slew Rate Characteristics

PARAMETER

MIN

MAX

UNIT

NOTES

Pull-up and Pull-Down Slew Rate for Full Strength Driver

0.7

2.5

V/ns

1,2

Pull-up and Pull-Down Slew Rate for Three-Quarter Strength Driver

0.5

1.75

V/ns

1,2

Pull-up and Pull-Down Slew Rate for Half Strength Driver

0.3

1.0

V/ns

1,2

Output Slew rate Matching ratio (Pull-up to Pull-down)

0.7

1.4

Notes:

1. Measured with a test load of 20 pF connected to VSSQ.

2. Output slew rate for rising edge is measured between VILD(DC) to VIHD(AC) and for falling edge between VIHD(DC) to VILD(AC).

3. The ratio of pull-up slew rate to pull-down slew rate is specified for the same temperature and voltage, over the entire temperature and

voltage range. For a given output, it represents the maximum difference between pull-up and pull-down drivers due to process variation.

8.5.3 AC Overshoot/Undershoot Specification

PARAMETER

SPECIFICATION

Maximum peak amplitude allowed for overshoot

0.5 V

Maximum peak amplitude allowed for undershoot

0.5 V

The area between overshoot signal and VDD must be less than or equal to

3 V-ns

The area between undershoot signal and GND must be less than or equal to

3 V-ns

8.5.4 AC Overshoot and Undershoot Definition

VDD

VSS

2.5

2.0

1.5

1.0

0.5

-0.5

Overshoot Area

Undershoot Area

Max Amplitude = 0.5V Max Area = 3V-ns

Voltage (V)

Time

(ns)

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 56 - Revision A01-003

9. PACKAGE DIMENSIONS

9.1: LPDDR X 16 VBGA60Ball (8X9 MM^2, Ball pitch:0.8mm)

Note:

1. Ball land:0.5mm. Ball opening:0.4mm. PCB Ball land suggested ≦0.4mm

2. Dimensions apply to Solder Balls Post-Reflow. The Pre-Reflow diameter is 0.42 on a 0.4 SMD Ball Pad.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 57 - Revision A01-003

9.2: LPDDR X 32 VBGA90Ball (8X13 MM^2, Ball pitch:0.8mm)

Note:

1. Ball land:0.5mm. Ball opening:0.4mm. PCB Ball land suggested ≦0.4mm

2. Dimensions apply to Solder Balls Post-Reflow. The Pre-Reflow diameter is 0.42 on a 0.4 SMD Ball Pad.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 58 - Revision A01-003

10. ORDERING INFORMATION

W 9 4 7 D 6 H B H X 5 I

Mobile LPDDR/LPSDR SDRAM Package Part Numbering

Product Line

98:mobile LPSDR SDRAM

94:mobile LPDDR SDRAM

Density

7:27=128M 8:28=256M

9:29=512M

Power Supply

D:1.8/1.8 VDD / VDDQ

I/O Ports width

6:16bit

2:32bit

Temperature

with standard Idd6

G:-25C~85C

Package Material

X: Lead-free + Halogen-free

Package or KGD

K: KGD

B: BGA

Package configuration code

G: 54VFBGA, 8mmx9mm

H: 60VFBGA, 8mmx9mm

J: 90VFBGA, 8mmx13mm

Generation

Design revision.

with low power Idd6

E:-25C~85C

I:-40C~85C

Clock rate

5:5ns200MHz

6:6ns166MHz

7:7.5ns133MHz

Part number

VDD/VDDQ I/O width Package Others

W947D6HBHX5I 1.8V/1.8V 16 60VFBGA

200MHz, -40C~85C, Low power

W947D6HBHX5E 1.8V/1.8V 16 60VFBGA

200MHz, -25C~85C, Low power

W947D6HBHX6E 1.8V/1.8V 16 60VFBGA

166MHz, -25C~85C, Low power

W947D6HBHX6G 1.8V/1.8V 16 60VFBGA

166MHz, -25C~85C

W947D2HBJX5I 1.8V/1.8V 32 90VFBGA

200MHz, -40C~85C, Low power

W947D2HBJX5E 1.8V/1.8V 32 90VFBGA 200MHz, -25C~85C, Low power

W947D2HBJX6E 1.8V/1.8V 32 90VFBGA

166MHz, -25C~85C, Low power

W947D2HBJX6G 1.8V/1.8V 32 90VFBGA 166MHz, -25C~85C

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 59 - Revision A01-003

11. REVISION HISTORY

VERSION

DATE

PAGE

DESCRIPTION

A01-001

04/08/2011

All

Product datasheet for customer.

A01-002

04/18/2011

Delete “2” in refresh rate of SRR for DQ8~10.

Remove IDD6 note 3.

A01-003

06/17/2011

48,49

Update CCk(Max) to 3 pF.

Add IiL & IoL.

Update IDD4R & IDD4W value.

W947D6HB / W947D2HB

128Mb Mobile LPDDR

Publication Release Date:Jun,17, 2011

- 60 - Revision A01-003

Important Notice

Winbond products are not designed, intended, authorized or warranted for use as components in systems or

equipment intended for surgical implantation, atomic energy control instruments, airplane or spaceship

instruments, transportation instruments, traffic signal instruments, combustion control instruments, or for

other applications intended to support or sustain life. Furthermore, Winbond products are not intended for

applications wherein failure of Winbond products could result or lead to a situation where in personal injury,

death or severe property or environmental damage could occur.

Winbond customers using or selling these products for use in such applications do so at their own risk and

agree to fully indemnify Winbond for any damages resulting from such improper use or sales.

-------------------------------------------------------------------------------------------------------------------------------------------------

Please note that all data and specifications are subject to change without notice.

All the trademarks of products and companies mentioned in the datasheet belong to their respective owners