MNR35 Resistors Compact 8-element Chip Resistor Networks MNR35 (1206x5 size) zFeatures 1) Common terminals yield area 40% smaller than that of the MNR38. 2) 8-element construction makes the MNR35 ideal for bus line pull-up / pull-down. 3) Convex electrodes Easy to check the fillet after soldering is finished. 4) Compatible with a wide range of mounting equipment. Squared corners make it excellent for mounting using image recognition devices. 5) ROHM resistors have approved ISO9001- / ISO/TS 16949- certification. Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product before using or ordering it. zRatings Item Rated power Conditions Specifications Power must be derated according to the power derating curve in Figure 1 when ambient temperature exceeds 70C. 0.063W (1 / 16W) at 70C POWER LOAD (%) 100 80 60 40 20 0 -55 0 70 100 125 AMBIENT TEMPERATURE (C) Fig.1 Rated voltage The voltage rating is calculated by the following equation. If the value obtained exceeds the limiting element voltage, the voltage rating is equal to the maximum operating voltage. E: Rated voltage (V) E= PxR P: Rated power (W) Limiting element voltage R: Nominal resistance () Nominal resistance 50V See Table 1. -55C to +125C Operating temperature Table 1 Resistance tolerance J (5%) Resistance range () 56R100k (E12) Resistance temperature coefficient (ppm / C) 200 *Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that is greater than its rated voltage. Rev.D 1/3 MNR35 Resistors zCharacteristics Guaranteed value Resistor type Item Test conditions (JIS C 5201-1) J : 5% Resistance Variation of resistance with temperature JIS C 5201-1 4.5 JIS C 5201-1 4.8 Measurement : -55 / +25 / +125C See Table.1 JIS C 5201-1 4.13 Rated voltage (current) x2.5, 2s. Maximum Overload Voltage : 100V (2.0%+0.1) Overload A new uniform coating of minimum of 95% of the surface being immersed and no soldering damage. Solderability JIS C 5201-1 4.17 Rosin*Ethanol (25%WT) Soldering condition : 2355C Duration of immersion : 2.00.5s. (1.0%+0.1) No remarkable abnormality on the appearance. Resistance to soldering heat Rapid change of temperature (1.0%+0.1) JIS C 5201-1 4.19 Test temp. : -55C to +125C 5cyc (3.0%+0.1) JIS C 5201-1 4.24 40C, 93%RH Test time : 1,000h to 1,048h (3.0%+0.1) JIS C 5201-1 4.25.1 Rated voltage (current), 70C 1.5h : ON - 0.5h : OFF Test time : 1,000h to 1,048h (3.0%+0.1) JIS C 5201-1 4.25.3 125C Test time : 1,000h to 1,048h (1.0%+0.1) JIS C 5201-1 4.29 235C, Immersion cleaning, 50.5min. Solvent : 2-propanol Damp heat, steady state Endurance at 70C Endurance Resistance to solvent (1.0%+0.05) Without mechanical damage such as breaks. Bend strength of the end face plating JIS C 5201-1 4.18 Soldering condition : 2605C Duration of immersion : 101s. JIS C 5201-1 4.33 zDimensions (Unit : mm) Cross section A-A' 6.40.4 1.27 2 1 6 1 1 1 B Material Max.0.5 R 1 0 3 0.50.3 A' 3.10.2 5 A Cross section B-B' 6 1 5 0.550.1 B' 0.50.2 1.00.2 2 3 4 1 Resistive element (Oxide metal thick film) 2 Silver thick film electrode 3 Nickel electrode 4 Sn electrode 5 Alumina substrate 6 Overcoating (Glass) 0.80.2 Pitch of the upper electrode. Rev.D 2/3 MNR35 Resistors zEquivalent circuit R1 R8 R7 R6 R2 R3 R4 R5 R1 = R2 = R3 = R4 = R5 = R6 = R7 = R8 zPackaging Reel Taping P2 E B0 02 04 06 08 06 D 04 B 02 A 08 W F D 0 P0 A0 K P1 C (Unit : mm) Label W F E A0 B0 12.00.3 5.50.05 1.750.1 3.40.1 6.60.1 D0 P0 P1 P2 K +0.1 1.5 0 4.00.1 4.00.1 2.00.05 1.00.15 EIAJ ET-7200B compliant (Unit : mm) A 180 B 0 -1.5 60 C +1 0 13 +1.0 -0 D 130.2 zPart No. Explanation M N R 3 5 Part No. J 5 R J Resistance tolerance Nominal resistance J 5% J is also used for jumper Resistance code,3 digits, 000 denotes Jumper type. Packaging Specifications Code Part No. Code MNR35 J5R Resistance tolerance J(5%) Packaging specifications Reel Basic ordering unit (pcs) Embossed tape (4mm Pitch) 180mm (7in.) 4,000 Reel (180) : JEITA ET-7200B : Standard product Rev.D 3/3 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office. ROHM Customer Support System www.rohm.com Copyright (c) 2008 ROHM CO.,LTD. THE AMERICAS / EUROPE / ASIA / JAPAN Contact us : webmaster@ rohm.co. jp 21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121 FAX : +81-75-315-0172 Appendix1-Rev2.0