HMC597LP4 / 597LP4E v06.0613 Demodulators - SMT SiGe WIDEBAND DIRECT DEMODULATOR RFIC, 100 - 4000 MHz Typical Applications Features The HMC597LP4 / HMC597LP4E is suitable for various modulation systems: High Linearity: +25 dBm IIP3 & +60 dBm IIP2 * Cellular/PCS/3G High Integration: On-Chip RF Balun Low Noise Figure: 15 dB * Base Stations & Repeaters * GSM/GPRS, WCDMA & TD-SCDMA * WiMAX, WiBro & Fixed Wireless Functional Diagram General Description The HMC597LP4(E) are highly integrated SiGe wideband direct conversion I/Q Demodulator RFICs which are ideal for high dynamic range receivers operating from 100 - 4000 MHz in cellular and broadband wireless infrastructure applications. Providing a very high level of integration compared with discrete solutions, the HMC597LP4(E) features an on-chip RF balun which allows for singled ended RF input. An off-chip capacitor allows the reconfiguration of the RF port to operate over the whole 100 - 4000 MHz band without additional off-chip components. Also ideal for software radio and other multi-band receivers, the HMC597LP4(E) demodulator is housed in a compact 4 x 4 mm SMT QFN package and delivers exceptionally high dynamic range. The LO requires -6 to +6 dBm and can be driven in single-ended mode. The I and Q output ports are differential with an output impedance of 400 Ohms, allowing direct connection to channel filters and ADCs. This device is optimized for a supply voltage of +4.5V to +5.5V and consumes 200 mA @ +5V supply. Electrical Specifications, See Test Conditions on following page herein. Parameter RF Input Frequency (Direct LO) Typ. Max. Units 0.1 - 4.0 GHz Input P1dB 12 dBm SSB Noise Figure 15 dB +25 dBm Input IP2 +60 dBm Conversion Gain -3.5 dB Input IP3 I/Q Gain Mismatch 0.1 LO to RF Leakage @ +3 dBm LO -66 IF Port Bandwidth 600 MHz IF Output Impedance (Diff.) 400 Ohms -6 to +6 dBm LO Input Power 1 Min. LO/RF Return Loss 12/12 Total Supply Current 200 0.25 dB dBm dB 230 mA For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC597LP4 / 597LP4E v06.0613 SiGe WIDEBAND DIRECT DEMODULATOR RFIC, 100 - 4000 MHz AC Test Conditions [1] Parameter Condition Parameter Condition Supply 200mA @ +5V RF Input Frequency 1970 MHz 124mA @ +2.8V RF Input Frequency for IIP3 1970 & 1971 MHz 76mA @ +3.5V RF Input Power for IIP3 0 dBm per Tone LO Frequency 1960 MHz LO Input Power 0 dBm single ended through LOP VccLO [2] QN, QP, IN, IP [2] [1] Unless otherwise specified, the following test conditions were used. Please refer to the HMC597LP4(E) application schematic. [2] Voltages at these pins are supplied through bias resistors from Vsupply, 5V (see application circuit). Power dissipation on chip is 124 x 2.8 + 76 x 3.5 = 613.2mW. Thermal rise calculations should be based on this power dissipation level. P1dB, Noise Figure, Gain vs. Frequency [1] Input IP3 vs. Frequency [1] 40 25 35 C26= 0pF C26= 6.8pF C26= 0.9pF 20 30 NF 15 10 INPUT IP3 (dBm) NF (dB), P1dB (dBm) & GAIN (dB) 30 P1dB 5 25 20 15 0 10 -5 5 GAIN -10 C26= 0pF C26= 6.8pF C26= 0.9pF 0 0 0.5 1 1.5 2 2.5 3 3.5 4 0 0.5 1 RF FREQUENCY (GHz) 1.5 2 2.5 3 3.5 4 3.5 4 RF FREQUENCY (GHz) RF Return Loss vs. Frequency LO & Return Loss vs. Frequency 0 0 C26=0pF RETURN LOSS (dB) RF RETURN LOSS (dB) Demodulators - SMT DC Test Conditions [1] -5 C26=6.8pF -10 -5 -10 -15 C26=0.9pF -15 -20 0 0.5 1 1.5 2 2.5 RF FREQUENCY (GHz) 3 3.5 4 0 0.5 1 1.5 2 2.5 3 RF FREQUENCY (GHz) [1] IF Frequency= 10 MHz For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 2 HMC597LP4 / 597LP4E v06.0613 SiGe WIDEBAND DIRECT DEMODULATOR RFIC, 100 - 4000 MHz Noise Figure, P1dB, Gain @ 900 MHz vs. LO Power [1] LO - RF Isolation vs. Frequency 25 NF (dB), P1dB (dBm) & GAIN (dB) LO-RF ISOLATION (dB) -20 -40 -60 -80 NF 20 15 10 P1dB 5 0 -5 GAIN -10 -100 0 0.5 1 1.5 2 2.5 3 3.5 -9 4 -6 -3 0 3 6 9 LO POWER (dBm) RF FREQUENCY (GHz) Noise Figure, P1dB, Gain @ 1970 MHz vs. LO Power [1] Noise Figure, P1dB, Gain @ 3500 MHz vs. LO Power [1] 25 25 20 NF (dB), P1dB (dBm) & GAIN (dB) NF (dB), P1dB (dBm) & GAIN (dB) Demodulators - SMT 0 NF 15 10 P1dB 5 0 -5 GAIN -10 NF 20 15 10 P1dB 5 0 -5 GAIN -10 -9 -6 -3 0 LO POWER (dBm) 3 6 9 -9 -6 -3 0 3 6 9 LO POWER (dBm) [1] IF Frequency= 10 MHz 3 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC597LP4 / 597LP4E v06.0613 SiGe WIDEBAND DIRECT DEMODULATOR RFIC, 100 - 4000 MHz Vcc1, Vcc2 +6V LO Input Power +12 dBm Channel Temperature 150 C Thermal Resistance (Rth) (channel to ground paddle) 8.9 C/W Storage Temperature -65 to +150 C Operating Temperature -40 to +85 C ESD Sensitivity (HBM) Class 1B ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing Demodulators - SMT Absolute Maximum Ratings NOTES: 1.LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3.LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC597LP4 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 [1] HMC597LP4E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 [2] Package Marking [3] H597 XXXX H597 XXXX [1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 260 C [3] 4-Digit lot number XXXX For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 4 HMC597LP4 / 597LP4E v06.0613 SiGe WIDEBAND DIRECT DEMODULATOR RFIC, 100 - 4000 MHz Demodulators - SMT Pin Descriptions 5 Pin Number Function Description 1 VccLO Supply for LO Amplifier. Typically draws 124mA @ 2.8V. 2, 5, 8, 11, 12, 14, 17, 19, 20, 23 GND These pins and the ground paddle should be connected to a high quality RF/DC ground. 3 LOP LO input. Need a DC decoupling capacitor. Typically at 1.5 - 1.8 VDC. 4 LON This pin should be AC grounded. Also can be used to optimize the IP2 performances 6, 7, 24 N/C Not Connected 9, 10 QN, QP 21, 22 IP, IN Differential baseband outputs. 400 Ohms differential output impedance. Each port should draw 38 mA @ 3.5V. 12, 19 VccQ, VccI Decoupling for the Q and I mixer stages. 13, 18 CTRFQ, CTRFI Center tap of the RF transformer. Should be connected to a high quality RF/DC ground. Interface Schematic For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC597LP4 / 597LP4E v06.0613 SiGe WIDEBAND DIRECT DEMODULATOR RFIC, 100 - 4000 MHz Pin Descriptions (Continued) Function Description 15 RFN RF Input. 16 RFP Can be DC or RF grounded. This pin is used to match the RF port over the desired frequency range. Also can be used to drive the RF port differentially if needed. Interface Schematic For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com Demodulators - SMT Pin Number 6 HMC597LP4 / 597LP4E v06.0613 SiGe WIDEBAND DIRECT DEMODULATOR RFIC, 100 - 4000 MHz Demodulators - SMT Evaluation PCB Evaluation PCB 115775 [1][2] Item Description J1 - J6 PCB Mount SMA Connector J7, J8 2 mm DC Header C11, C20 - C24 1000 pF Capacitor, 0402 Pkg. C12 100 pF Capacitor, 0402 Pkg. C25 0.3 pF Capacitor, 0402 Pkg. C26 0.9 pF Capacitor, 0402 Pkg. C30 - C32 0.1 F Capacitor, 0805 Pkg. R3, R4 39.2 Ohm Resistor, 0402 Pkg. R5 18.2 Ohm Resistor, 0402 Pkg. L1 - L4 5.6 nH Inductor, 0402 Pkg. T1, T2 2 - 800 MHz Balun U1 HMC597LP3 / HMC597LP3E Direct Demodulator PCB [2] 116265 Evaluation PCB The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 7 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC597LP4 / 597LP4E v06.0613 SiGe WIDEBAND DIRECT DEMODULATOR RFIC, 100 - 4000 MHz Demodulators - SMT Application & Evaluation PCB Schematic * Short to ground for single ended mode. For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 8