For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
DEMODULATORS - SMT
1
HMC597LP4 / 597LP4E
v06.0613
SiGe WIDEBAND DIRECT
DEMODULATOR RFIC, 100 - 4000 MHz
General Description
Features
Functional Diagram
The HMC597LP4(E) are highly integrated SiGe
wideband direct conversion I/Q Demodulator RFICs
which are ideal for high dynamic range receivers
operating from 100 - 4000 MHz in cellular and
broadband wireless infrastructure applications.
Providing a very high level of integration compared
with discrete solutions, the HMC597LP4(E) features an
on-chip RF balun which allows for singled ended RF
input. An off-chip capacitor allows the reconī˜Ÿguration
of the RF port to operate over the whole 100 - 4000
MHz band without additional off-chip components.
Also ideal for software radio and other multi-band
receivers, the HMC597LP4(E) demodulator is housed
in a compact 4 x 4 mm SMT QFN package and delivers
exceptionally high dynamic range. The LO requires -6
to +6 dBm and can be driven in single-ended mode.
The I and Q output ports are differential with an output
impedance of 400 Ohms, allowing direct connection to
channel ī˜Ÿlters and ADCs. This device is optimized for
a supply voltage of +4.5V to +5.5V and consumes 200
mA @ +5V supply.
High Linearity: +25 dBm IIP3 & +60 dBm IIP2
Low Noise Figure: 15 dB
High Integration: On-Chip RF Balun
Typical Applications
The HMC597LP4 / HMC597LP4E is suitable for
various modulation systems:
ā€¢ Cellular/PCS/3G
ā€¢ Base Stations & Repeaters
ā€¢ GSM/GPRS, WCDMA & TD-SCDMA
ā€¢ WiMAX, WiBro & Fixed Wireless
Electrical Speciī˜Ÿcations, See Test Conditions on following page herein.
Parameter Min. Ty p. Max. Units
RF Input Frequency (Direct LO) 0.1 - 4.0 GHz
Input P1dB 12 dBm
SSB Noise Figure 15 dB
Input IP3 +25 dBm
Input IP2 +60 dBm
Conversion Gain -3.5 dB
I/Q Gain Mismatch 0.1 0.25 dB
LO to RF Leakage @ +3 dBm LO -66 dBm
IF Port Bandwidth 600 MHz
IF Output Impedance (Diff.) 400 Ohms
LO Input Power -6 to +6 dBm
LO/RF Return Loss 12/12 dB
Total Supply Current 200 230 mA
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
DEMODULATORS - SMT
2
HMC597LP4 / 597LP4E
v06.0613
SiGe WIDEBAND DIRECT
DEMODULATOR RFIC, 100 - 4000 MHz
P1dB, Noise Figure, Gain vs. Frequency [1] Input IP3 vs. Frequency [1]
RF Return Loss vs. Frequency LO & Return Loss vs. Frequency
-10
-5
0
5
10
15
20
25
30
0 0.5 1 1.5 2 2.5 3 3.5 4
C26= 0pF
C26= 6.8pF
C26= 0.9pF
NF (dB), P1dB (dBm) & GAIN (dB)
RF FREQUENCY (GHz)
NF
P1dB
GAIN
0
5
10
15
20
25
30
35
40
0 0.5 1 1.5 2 2.5 3 3.5 4
C26= 0pF
C26= 6.8pF
C26= 0.9pF
INPUT IP3 (dBm)
RF FREQUENCY (GHz)
-15
-10
-5
0
0 0.5 1 1.5 2 2.5 3 3.5 4
RF RETURN LOSS (dB)
RF FREQUENCY (GHz)
C26=0pF
C26=6.8pF
C26=0.9pF
-20
-15
-10
-5
0
0 0.5 1 1.5 2 2.5 3 3.5 4
RETURN LOSS (dB)
RF FREQUENCY (GHz)
DC Test Conditions [1]
Parameter Condition
Supply 200mA @ +5V
VccLO [2] 124mA @ +2.8V
QN, QP, IN, IP [2] 76mA @ +3.5V
[1] Unless otherwise speciī˜Ÿed, the following test conditions were
used. Please refer to the HMC597LP4(E) application schematic.
[2] Voltages at these pins are supplied through bias resistors from
Vsupply, 5V (see application circuit). Power dissipation on chip is
124 x 2.8 + 76 x 3.5 = 613.2mW.
Thermal rise calculations should be based on this power dissipa-
tion level.
AC Test Conditions [1]
Parameter Condition
RF Input Frequency 1970 MHz
RF Input Frequency for IIP3 1970 & 1971 MHz
RF Input Power for IIP3 0 dBm per Tone
LO Frequency 1960 MHz
LO Input Power 0 dBm single ended through LOP
[1] IF Frequency= 10 MHz
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
DEMODULATORS - SMT
3
HMC597LP4 / 597LP4E
v06.0613
SiGe WIDEBAND DIRECT
DEMODULATOR RFIC, 100 - 4000 MHz
Noise Figure, P1dB,
Gain @ 900 MHz vs. LO Power [1]
Noise Figure, P1dB,
Gain @ 1970 MHz vs. LO Power [1]
Noise Figure, P1dB,
Gain @ 3500 MHz vs. LO Power [1]
-10
-5
0
5
10
15
20
25
-9 -6 -3 0 3 6 9
NF (dB), P1dB (dBm) & GAIN (dB)
LO POWER (dBm)
NF
P1dB
GAIN
-10
-5
0
5
10
15
20
25
-9 -6 -3 0 3 6 9
NF (dB), P1dB (dBm) & GAIN (dB)
LO POWER (dBm)
NF
P1dB
GAIN
-10
-5
0
5
10
15
20
25
-9 -6 -3 0 3 6 9
NF (dB), P1dB (dBm) & GAIN (dB)
LO POWER (dBm)
NF
P1dB
GAIN
LO - RF Isolation vs. Frequency
-100
-80
-60
-40
-20
0
0 0.5 1 1.5 2 2.5 3 3.5 4
LO-RF ISOLATION (dB)
RF FREQUENCY (GHz)
[1] IF Frequency= 10 MHz
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
DEMODULATORS - SMT
4
HMC597LP4 / 597LP4E
v06.0613
SiGe WIDEBAND DIRECT
DEMODULATOR RFIC, 100 - 4000 MHz
Absolute Maximum Ratings
Vcc1, Vcc2 +6V
LO Input Power +12 dBm
Channel Temperature 150 Ā°C
Thermal Resistance (Rth)
(channel to ground paddle) 8.9 Ā°C/W
Storage Temperature -65 to +150 Ā°C
Operating Temperature -40 to +85 Ā°C
ESD Sensitivity (HBM) Class 1B
Outline Drawing
Part Number Package Body Material Lead Finish MSL Rating Package Marking [3]
HMC597LP4 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 [1] H597
XXXX
HMC597LP4E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 [2] H597
XXXX
[1] Max peak reī˜žow temperature of 235 Ā°C
[2] Max peak reī˜žow temperature of 260 Ā°C
[3] 4-Digit lot number XXXX
Package Information
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS].
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST
BE SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
PCB LAND PATTERN.
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
DEMODULATORS - SMT
5
HMC597LP4 / 597LP4E
v06.0613
SiGe WIDEBAND DIRECT
DEMODULATOR RFIC, 100 - 4000 MHz
Pin Number Function Description Interface Schematic
1VccLO Supply for LO Ampliī˜Ÿer.
Typically draws 124mA @ 2.8V.
2, 5, 8, 11,
12, 14, 17, 19,
20, 23
GND These pins and the ground paddle should be
connected to a high quality RF/DC ground.
3LOP LO input. Need a DC decoupling capacitor.
Typically at 1.5 - 1.8 VDC.
4LON
This pin should be AC grounded.
Also can be used to optimize the IP2
performances
6, 7, 24 N/C Not Connected
9, 10
21, 22
QN, QP
IP, I N
Differential baseband outputs.
400 Ohms differential output impedance.
Each port should draw 38 mA @ 3.5V.
12, 19 VccQ, VccI Decoupling for the Q and I mixer stages.
13, 18 CTRFQ, CTRFI Center tap of the RF transformer. Should be
connected to a high quality RF/DC ground.
Pin Descriptions
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
DEMODULATORS - SMT
6
HMC597LP4 / 597LP4E
v06.0613
SiGe WIDEBAND DIRECT
DEMODULATOR RFIC, 100 - 4000 MHz
Pin Number Function Description Interface Schematic
15 RFN RF Input.
16 RFP
Can be DC or RF grounded. This pin is used to
match the RF port over the desired frequency
range. Also can be used to drive the RF port
differentially if needed.
Pin Descriptions (Continued)
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
DEMODULATORS - SMT
7
HMC597LP4 / 597LP4E
v06.0613
SiGe WIDEBAND DIRECT
DEMODULATOR RFIC, 100 - 4000 MHz
Evaluation PCB
The circuit board used in the ī˜Ÿnal application should
use RF circuit design techniques. Signal lines
should have 50 ohm impedance while the package
ground leads and exposed paddle should be con-
nected directly to the ground plane similar to that
shown. A sufficient number of via holes should be
used to connect the top and bottom ground planes.
The evaluation circuit board shown is available from
Hittite upon request.
Evaluation PCB 115775 [1][2]
Item Description
J1 - J6 PCB Mount SMA Connector
J7, J8 2 mm DC Header
C11, C20 - C24 1000 pF Capacitor, 0402 Pkg.
C12 100 pF Capacitor, 0402 Pkg.
C25 0.3 pF Capacitor, 0402 Pkg.
C26 0.9 pF Capacitor, 0402 Pkg.
C30 - C32 0.1 ĀµF Capacitor, 0805 Pkg.
R3, R4 39.2 Ohm Resistor, 0402 Pkg.
R5 18.2 Ohm Resistor, 0402 Pkg.
L1 - L4 5.6 nH Inductor, 0402 Pkg.
T1, T2 2 - 800 MHz Balun
U1 HMC597LP3 / HMC597LP3E
Direct Demodulator
PCB [2] 116265 Evaluation PCB
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
DEMODULATORS - SMT
8
HMC597LP4 / 597LP4E
v06.0613
SiGe WIDEBAND DIRECT
DEMODULATOR RFIC, 100 - 4000 MHz
Application & Evaluation PCB Schematic
* Short to ground for single ended mode.