December 2004
Copyright © Alliance Semiconductor. All rights reserved.
®
AS7C251MNTD18A
12/23/04, v.2.2 Alliance Semiconductor P. 1 of 18
2.5V 1M x 18 Pipelined SRAM with NTDTM
Features
• Organization: 1,048,576 words × 18 bits
•NTD
™architecture for efficient bus operation
• Fast clock speeds to 166 MHz
• Fast clock to data access: 3.5/3.8 ns
•Fast OE
access time: 3.5/3.8 ns
• Fully synchronous operation
• Asynchronous output enable control
• Available in 100-pin TQFP package
• Individual byte write and global write
• Clock enable for operation hold
• Multiple chip enables for easy expansion
• 2.5V core power supply
• Self-timed write cycles
• Interleaved or linear burst modes
• Snooze mode for standby operation
Logic block diagram
Write Buffer
Address
DQ
CLK
register
Output
register
DQ [a,b]
20
20
CLK
CE0
CE1
CE2
A[19:0]
OE
CLK
CEN
Control
CLK
logic
Data
DQ
CLK
input
register
18 18
OE
1M x 18
SRAM
array
R/W
DQ [a,b]
BWa
BWb
CLK
Q
D
ADV / LD
LBO
burst logic
addr. registers
Write delay
20
ZZ
CLK
18 18
18
18
Selection guide
-166 -133 Units
Minimum cycle time 6 7.5 ns
Maximum clock frequency 166 133 MHz
Maximum clock access time 3.5 3.8 ns
Maximum operating current 290 270 mA
Maximum standby current 85 75 mA
Maximum CMOS standby current (DC) 40 40 mA
®
AS7C251MNTD18A
12/23/04, v.2.2 Alliance Semiconductor P. 2 of 18
16 Mb 2.5V Synchronous SRAM products list1,2
1 Core Power Supply: VDD = 2.5V + 0.125V
2 I/O Supply Voltage: VDDQ = 2.5V + 0.125V
PL-SCD : Pipelined Burst Synchronous SRAM - Single Cycle Deselect
PL-DCD : Pipelined Burst Synchronous SRAM - Double Cycle Deselect
FT : Flow-through Burst Synchronous SRAM
NTD1-PL : Pipelined Burst Synchronous SRAM with NTDTM
NTD-FT : Flow-through Burst Synchronous SRAM with NTDTM
Org Part Number Mode Speed
1MX18 AS7C251MPFS18A PL-SCD 166/133 MHz
512KX32
AS7C25512PFS32A PL-SCD 166/133 MHz
512KX36
AS7C25512PFS36A PL-SCD 166/133 MHz
1MX18 AS7C251MPFD18A PL-DCD 166/133 MHz
512KX32
AS7C25512PFD32A PL-DCD 166/133 MHz
512KX36
AS7C25512PFD36A PL-DCD 166/133 MHz
1MX18 AS7C251MFT18A FT 7.5/8.5/10 ns
512KX32
AS7C25512FT32A FT 7.5/8.5/10 ns
512KX36
AS7C25512FT36A FT 7.5/8.5/10 ns
1MX18 AS7C251MNTD18A NTD-PL 166/133 MHz
512KX32
AS7C25512NTD32A NTD-PL 166/133 MHz
512KX36
AS7C25512NTD36A NTD-PL 166/133 MHz
1MX18 AS7C251MNTF18A NTD-FT 7.5/8.5/10 ns
512KX32
AS7C25512NTF32A NTD-FT 7.5/8.5/10 ns
512KX36
AS7C25512NTF36A NTD-FT 7.5/8.5/10 ns
1. NTD: No Turnaround Delay. NTDTM is a trademark of Alliance Semiconductor Corporation. All trademarks mentioned in this document are the property
of their respective owners.
®
AS7C251MNTD18A
12/23/04, v.2.2 Alliance Semiconductor P. 3 of 18
Pin assignment
100-pin TQFP - top view
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
LBO
A
A
A
A
A1
A0
NC
NC
V
SS
V
DD
NC
NC
A
A
A
A
A
A
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
A
A
CE0
CE1
NC
NC
BWb
BWa
CE2
V
DD
V
SS
CLK
R/W
CEN
OE
ADV/LD
A
A
A
TQFP 14 x 20mm
A
NC
NC
NC
V
DDQ
V
SSQ
NC
NC
DQb0
DQb1
V
SSQ
V
DDQ
DQb2
DQb3
NC
V
DD
NC
V
SS
DQb4
DQb5
V
DDQ
V
SSQ
DQb6
DQb7
DQPb
NC
V
SSQ
V
DDQ
NC
NC
NC
A
NC
NC
V
DDQ
V
SSQ
NC
DQPa
DQa7
DQa6
V
SSQ
V
DDQ
DQa5
DQa4
V
SS
ZZ
DQa3
DQa2
V
DDQ
V
SSQ
DQa1
DQa0
NC
NC
V
SSQ
V
DDQ
NC
NC
NC
V
DD
NC
A
®
AS7C251MNTD18A
12/23/04, v.2.2 Alliance Semiconductor P. 4 of 18
Functional description
The AS7C251MNTD18A family is a high performance CMOS 16-Mbit synchronous Static Random Access Memory (SRAM) organized as
1,048,576 words × 18 bits and incorporates a LATE LATE Write.
This variation of the 16Mb+ synchronous SRAM uses the No Turnaround Delay (NTD™) architecture, featuring an enhanced write
operation that improves bandwidth over pipelined burst devices. In a normal pipelined burst device, the write data, command, and address
are all applied to the device on the same clock edge. If a read command follows this write command, the system must wait for two 'dead'
cycles for valid data to become available. These dead cycles can significantly reduce overall bandwidth for applications requiring random
access or read-modify-write operations.
NTD™ devices use the memory bus more efficiently by introducing a write latency which matches the two-cycle pipelined or one-cycle
flow-through read latency. Write data is applied two cycles after the write command and address, allowing the read pipeline to clear. With
NTD™, write and read operations can be used in any order without producing dead bus cycles.
Assert R/W low to perform write cycles. Byte write enable controls write access to specific bytes, or can be tied low for full 18 bit writes.
Write enable signals, along with the write address, are registered on a rising edge of the clock. Write data is applied to the device two clock
cycles later. Unlike some asynchronous SRAMs, output enable OE does not need to be toggled for write operations; it can be tied low for
normal operations. Outputs go to a high impedance state when the device is de-selected by any of the three chip enable inputs. In pipelined
mode, a two cycle deselect latency allows pending read or write operations to be completed.
Use the ADV (burst advance) input to perform burst read, write and deselect operations. When ADV is high, external addresses, chip select, R/W
pins are ignored, and internal address counters increment in the count sequence specified by the LBO control. Any device operations, including
burst, can be stalled using the CEN=1, the clock enable input.
The AS7C251MNTD18A operates with a 2.5V ± 5% power supply for the device core (VDD). These devices are available in a 100-pin
TQFP package.
TQFP capacitance
* Guaranteed not tested
TQFP thermal resistance
Parameter Symbol Test conditions Min Max Unit
Input capacitance CIN*VIN = 0V - 5 pF
I/O capacitance CI/O*VOUT = 0V - 7 pF
Description Conditions Symbol Typical Units
Thermal resistance
(junction to ambient)1
1 This parameter is sampled
Test conditions follow standard test methods
and procedures for measuring thermal
impedance, per EIA/JESD51
1–layer θJA 40 °C/W
4–layer θJA 22 °C/W
Thermal resistance
(junction to top of case)1θJC 8°C/W
®
AS7C251MNTD18A
12/23/04, v.2.2 Alliance Semiconductor P. 5 of 18
Signal descriptions
Snooze Mode
SNOOZE MODE is a low current, power-down mode in which the device is deselected and current is reduced to ISB2. The duration of
SNOOZE MODE is dictated by the length of time the ZZ is in a High state.
The ZZ pin is an asynchronous, active high input that causes the device to enter SNOOZE MODE.
When the ZZ pin becomes a logic High, ISB2 is guaranteed after the time tZZI is met. After entering SNOOZE MODE, all inputs except ZZ
is disabled and all outputs go to High-Z. Any operation pending when entering SNOOZE MODE is not guaranteed to successfully complete.
Therefore, SNOOZE MODE (READ or WRITE) must not be initiated until valid pending operations are completed. Similarly, when exiting
SNOOZE MODE during tPUS, only a DESELECT or READ cycle should be given while the SRAM is transitioning out of SNOOZE
MODE.
Signal I/O Properties Description
CLK I CLOCK Clock. All inputs except OE, LBO, and ZZ are synchronous to this clock.
CEN I SYNC Clock enable. When de-asserted high, the clock input signal is masked.
A, A0, A1 I SYNC Address. Sampled when all chip enables are active and ADV/LD is asserted.
DQ[a,b] I/O SYNC Data. Driven as output when the chip is enabled and OE is active.
CE0, CE1,
CE2 I SYNC Synchronous chip enables. Sampled at the rising edge of CLK, when ADV/LD is asserted.
Are ignored when ADV/LD is high.
ADV/LD I SYNC Advance or Load. When sampled high, the internal burst address counter will increment in
the order defined by the LBO input value. When low, a new address is loaded.
R/W I SYNC A high during LOAD initiates a READ operation. A low during LOAD initiates a WRITE
operation. Is ignored when ADV/LD is high.
BW[a,b] I SYNC Byte write enables. Used to control write on individual bytes. Sampled along with WRITE
command and BURST WRITE.
OE I ASYNC Asynchronous output enable. I/O pins are not driven when OE is inactive.
LBO ISTATIC
Selects Burst mode. When tied to VDD or left floating, device follows interleaved Burst order. When
driven Low, device follows linear Burst order. This signal is internally pulled High.
ZZ I ASYNC Snooze. Places device in low power mode; data is retained. Connect to GND if unused.
NC - - No connects.
®
AS7C251MNTD18A
12/23/04, v.2.2 Alliance Semiconductor P. 6 of 18
Burst order
Synchronous truth table[5,6,7,8,9,11]
Key: X = Don’t Care, H = HIGH, L = LOW. BWn = H means all byte write signals (BWa, BWb, BWc, and BWd) are HIGH. BWn = L means one or
more byte write signals are LOW.
Notes:
1 CONTINUE BURST cycles, whether READ or WRITE, use the same control inputs. The type of cycle performed (READ or WRITE) is chose in the initial
BEGIN BURST cycle. A CONINUE DESELECT cycle can only be entered if a DESELECT CYCLE is executed first.
2 DUMMY READ and WRITE ABORT cycles can be considered NOPs because the device performs no external operation. A WRITE ABORT means a
WRITE command is given, but no operation is performed.
3 OE may be wired LOW to minimize the number of control signal to the SRAM. The device will automatically turn off the output drivers during a WRITE
cycle. OE may be used when the bus turn-on and turn-off times do not meet an application’s requirements.
4 If an INHIBIT CLOCK command occurs during a READ operation, the DQ bus will remain active (Low-Z). If it occurs during a WRITE cycle, the bus will
remain in High-Z. No WRITE operations will be performed during the INHIBIT CLOCK cycle.
5 BWa enables WRITEs to byte “a” (DQa pins); BWb enables WRITEs to byte “b” (DQb pins); BWc enables WRITEs to byte “c” (DQc pins); BWd
enables WRITEs to byte “d” (DQd pins).
6 All inputs except OE and ZZ must meet setup and hold times around the rising edge (LOW to HIGH) of CLK.
7 Wait states are inserted by setting CEN HIGH.
8 This device contains circuitry that will ensure that the outputs will be in High-Z during power-up.
9 The device incorporates a 2-bit burst counter. Address wraps to the initial address every fourth BURST CYCLE.
10 The address counter is incremented for all CONTINUE BURST cycles.
11 ZZ pin is always Low in this truth table.
Interleaved burst order (LBO = 1) Linear burst order (LBO = 0)
A1A0 A1A0 A1A0 A1A0 A1A0 A1A0 A1A0 A1A0
Starting address 0 0 0 1 1 0 1 1 Starting Address 0 0 0 1 1 0 1 1
First increment 0 1 0 0 1 1 1 0 First increment 0 1 1 0 1 1 0 0
Second increment 1 0 1 1 0 0 0 1 Second increment 1 0 1 1 0 0 0 1
Third increment 1 1 1 0 0 1 0 0 Third increment 1 1 0 0 0 1 1 0
CE0 CE1 CE2 ADV/LD R/W BWnOE CEN
Address
source CLK Operation DQ Notes
H X X L X X X L NA L to H DESELECT Cycle High-Z
X X H L X X X L NA L to H DESELECT Cycle High-Z
X L X L X X X L NA L to H DESELECT Cycle High-Z
X X X H X X X L NA L to H CONTINUE DESELECT Cycle High-Z 1
L H L L H X L L External L to H READ Cycle (Begin Burst) Q
X X X H X X L L Next L to H READ Cycle (Continue Burst) Q 1,10
L H L L H X H L External L to H NOP/DUMMY READ (Begin Burst) High-Z 2
X X X H X X H L Next L to H DUMMY READ (Continue Burst) High-Z 1,2,10
L H L L L L X L External L to H WRITE CYCLE (Begin Burst) D 3
X X X H X L X L Next L to H WRITE CYCLE (Continue Burst) D 1,3,10
L H L L L H X L External L to H NOP/WRITE ABORT (Begin Burst) High-Z 2,3
X X X H X H X L Next L to H WRITE ABORT (Continue Burst) High-Z 1,2,3,
10
X X X X X X X H Current L to H INHIBIT CLOCK - 4
®
AS7C251MNTD18A
12/23/04, v.2.2 Alliance Semiconductor P. 7 of 18
State diagram for NTD SRAM
Absolute maximum ratings
Stresses greater than those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only, and functional
operation of the device at these or any other conditions outside those indicated in the operational sections of this specification is not implied. Exposure to
absolute maximum rating conditions may affect reliability.
Recommended operating conditions
Parameter Symbol Min Max Unit
Power supply voltage relative to GND VDD, VDDQ –0.3 +3.6 V
Input voltage relative to GND (input pins) VIN –0.3 VDD + 0.3 V
Input voltage relative to GND (I/O pins) VIN –0.3 VDDQ + 0.3 V
Power dissipation PD–1.8W
DC output current IOUT –50mA
Storage temperature Tstg –65 +150 oC
Temperature under bias (junction) Tbias –65 +150 oC
Parameter Symbol Min Nominal Max Unit
Supply voltage for inputs VDD 2.375 2.5 2.625 V
Supply voltage for I/O VDDQ 2.375 2.5 2.625 V
Ground supply Vss 0 0 0 V
Dsel
Dsel
Read
Read
Burst
Burst
Write
Read
Write
Burst
Read
Read
Write
Dsel
Read
Burst
Write
Dsel
Dsel
Write
Write
Burst
Dsel
Burst
Burst
Write
Read
®
AS7C251MNTD18A
12/23/04, v.2.2 Alliance Semiconductor P. 8 of 18
DC electrical characteristics
† LBO and ZZ pins have an internal pull-up or pull-down, and input leakage = ±10 µA.
*VIH max < VDD +1.5V for pulse width less than 0.2 X tCYC
**VIL min = -1.5 for pulse width less than 0.2 X tCYC
IDD operating conditions and maximum limits
Parameter Sym Conditions Min Max Unit
Input leakage current† |ILI|V
DD = Max, 0V < VIN < VDD -2 2 µA
Output leakage current |ILO|OE ≥ VIH, VDD = Max, 0V < VOUT < VDDQ -2 2 µA
Input high (logic 1) voltage VIH
Address and control pins 1.7* VDD+0.3 V
I/O pins 1.7* VDDQ+0.3 V
Input low (logic 0) voltage VIL
Address and control pins -0.3** 0.7 V
I/O pins -0.3** 0.7 V
Output high voltage VOH IOH = –4 mA, VDDQ = 2.375V 1.7 – V
Output low voltage VOL IOL = 8 mA, VDDQ = 2.625V – 0.7 V
Parameter Sym Conditions -166 -133 Unit
Operating power supply current1
1 ICC given with no output loading. ICC increases with faster cycle times and greater output loading.
ICC
CE0 < VIL, CE1 > VIH, CE2 < VIL, f = fMax,
IOUT = 0 mA, ZZ < VIL
290 270 mA
Standby power supply current
ISB
All VIN ≤ 0.2V or >
V
DD
– 0.2V,
Deselected,
f = fMax, ZZ < VIL
85 75
mA
ISB1
Deselected, f = 0, ZZ < 0.2V,
all VIN ≤ 0.2V or ≥ VDD – 0.2V 40 40
ISB2
Deselected, f = f
Max
, ZZ
≥
V
DD
– 0.2V,
all VIN ≤ VIL or ≥ VIH
40 40
®
AS7C251MNTD18A
12/23/04, v.2.2 Alliance Semiconductor P. 9 of 18
Timing characteristics over operating range
Snooze Mode Electrical Characteristics
Parameter Sym
-166 -133
Unit Notes1
1 See “Notes” on page 15
Min Max Min Max
Clock frequency FMAX – 166 – 133 MHz
Cycle time tCYC 6–7.5– ns
Clock access time tCD –3.5–3.8 ns
Output enable low to data valid tOE –3.5–3.8 ns
Clock high to output low Z tLZC 0–0– ns2, 3, 4
Data output invalid from clock high tOH 1.5–1.5– ns 2
Output enable low to output low Z tLZOE 0–0– ns2, 3, 4
Output enable high to output high Z tHZOE – 3.5 – 3.8 ns 2, 3, 4
Clock high to output high Z tHZC – 3.5 – 3.8 ns 2, 3, 4
Output enable high to invalid output tOHOE 0–0– ns
Clock high pulse width tCH 2.4–2.4– ns 5
Clock low pulse width tCL 2.3–2.4– ns 5
Address and Control setup to clock high tAS 1.5–1.5– ns 6
Data setup to clock high tDS 1.5–1.5– ns 6
Write setup to clock high tWS 1.5 – 1.5 – ns 6, 7
Chip select setup to clock high tCSS 1.5 – 1.5 – ns 6, 8
Address hold from clock high tAH 0.5–0.5– ns 6
Data hold from clock high tDH 0.5–0.5– ns 6
Write hold from clock high tWH 0.5 – 0.5 – ns 6, 7
Chip select hold from clock high tCSH 0.5 – 0.5 – ns 6, 8
Clock enable setup to clock high tCENS 1.5–1.5– ns 6
Clock enable hold from clock high tCENH 0.5–0.5– ns 6
ADV setup to clock high tADVS 1.5–1.5– ns 6
ADV hold from clock high tADVH 0.5–0.5– ns 6
Description Conditions Symbol Min Max Units
Current during Snooze Mode ZZ > VIH ISB2 40 mA
ZZ active to input ignored tPDS 2cycle
ZZ inactive to input sampled tPUS 2cycle
ZZ active to SNOOZE current tZZI 2cycle
ZZ inactive to exit SNOOZE current tRZZI 0cycle
®
AS7C251MNTD18A
12/23/04, v.2.2 Alliance Semiconductor P. 10 of 18
Key to switching waveforms
Timing waveform of read cycle
Undefined
Falling inputRising input don’t care
tCH tCYC
tCL
tAS
CLK
CEN
R/W
tCEH
A1 A2 A3
Address
tAH
tCES
tWS tWH
CE0,CE2
tADVS
tCSH
Dout
CE1
tADVH
tOE
tLZOE
tHZOE
Q(A1)
Q(A2Y‘01)
Q(A2) Q(A3)
tHLZC
OE
ADV/LD
BWn
tWS tWH
Q(A2Y‘10)
Q(A2Y‘11)
Read
Q(A1)
DSEL Read
Q(A2)
Continue
Read
Q(A2Y‘01)
Continue
Read
Q(A2Y‘10)
Continue
Read
Q(A2Y‘11)
Inhibit
Clock
Read
Q(A3)
Continue
Read
Q(A3Y‘01)
®
AS7C251MNTD18A
12/23/04, v.2.2 Alliance Semiconductor P. 11 of 18
Timing waveform of write cycle
tCH tCYC
tCL
tAS
CLK
CEN
R/W
tCEH
A1 A2 A3
Address
tAH
tCES
CE0,CE2
tADVS
tCSH
Din
CE1
tADVH
tHZOE
D(A1) D(A2) D(A3)
tDS
OE
ADV/LD
tDH
Q(n-2)
Dout
BWn
Q(n-1)
D(A2Y‘01) D(A2Y‘10) D(A2Y‘11)
Write
D(A1)
DSEL Write
D(A2)
Continue
Write
D(A2Y‘01)
Continue
Write
D(A2Y‘10)
Continue
Write
D(A2Y‘11)
Inhibit
Clock
Write
D(A3)
Continue
Write
D(A3Y‘01)
®
AS7C251MNTD18A
12/23/04, v.2.2 Alliance Semiconductor P. 12 of 18
Timing waveform of read/write cycle
Note: Ý = XOR when LBO = high/no connect. Ý = ADD when LBO = low. BW[a:d] is don’t care.
tCH tCYC
tCL
tCENS
tOH tOE
CLK
CEN
CE0, CE2
ADV/LD
R/W
ADDRESS
D/Q
OE
Command
tHZOE
BWn
A2A1 A3 A5A4
A7
A6
D(A1) D(A5) Q(A6)
D(A2)
D(A2
Ý
01)
Q(A3) Q(A4)
Q(A4
Ý
01
)
tCENH
tDS tDH tLZC
tCD
tHZC
tLZOE
Read
Q(A3) Read
Q(A4)
Burst
Read
Q(A4Ý01)
Write
D(A5)
Read
Q(A6)
Write
D(A7)
DSEL
tCSS
tADVH
tWS tWH
tWS tWH
CE1
Write
D(A1)
Write
D(A2)
tADVS
tCSH
tAS tAH
Burst
Write
D(A2Ý01)
®
AS7C251MNTD18A
12/23/04, v.2.2 Alliance Semiconductor P. 13 of 18
NOP, stall and deselect cycles
Note: Ý = XOR when LBO = high/no connect; Ý = ADD when LBO = low. OE is low.
CLK
CEN
CE0, CE2
ADV/LD
R/W
Address
D/Q
Command
BWn
A1 A2
Q(A1) D(A2)
Q(A1
Ý
01) Q(A1
Ý
10)
Burst
Q(A1Ý01
)
STALL DSEL Burst
DSEL
Write
D(A2)
Burst
NOP
D(A2Ý01
)
Write
NOP
D(A3)
A3
Read
Q(A1) Burst
Q(A1Ý10
)
Burst
D(A2Ý10)
CE1
®
AS7C251MNTD18A
12/23/04, v.2.2 Alliance Semiconductor P. 14 of 18
Timing waveform of snooze mode
CLK
All inputs
ZZ
tZZI
Isupply
(except ZZ)
Dout
tPUS
ZZ recovery cycle
ISB2
tRZZI
ZZ setup cycle
Deselect or Read Only Deselect or Read Only
Normal
operation
Cycle
High-Z
®
AS7C251MNTD18A
12/23/04, v.2.2 Alliance Semiconductor P. 15 of 18
AC test conditions
Notes:
1) For test conditions, see “AC test conditions”, Figures A, B, C
2) This parameter measured with output load condition in Figure C.
3) This parameter is sampled, but not 100% tested.
4) tHZOE is less than tLZOE and tHZC is less than tLZC at any given temperature and voltage.
5) tCH measured high above VIH and tCL measured as low below VIL
6) This is a synchronous device. All addresses must meet the specified setup and hold times for all rising edges of CLK. All other synchronous inputs must
meet the setup and hold times with stable logic levels for all rising edges of CLK when chip is enabled.
7) Write refers to R/
W
and
BW[a,b]
.
8) Chip select refers to
CE0
,
CE1
, and
CE2
.
Z
0
= 50
Ω
D
OUT
50
Ω
Figure B: Output load (A)
30 pF*
Figure A: Input waveform
10%
90%
GND
90%
10%
+
2.5V
• Output load: see Figure B, except for tLZC, tLZOE, tHZOE, tHZC, see Figure C.
• Input pulse level: GND to 2.5V. See Figure A.
• Input rise and fall time (measured at 0.25V and 2.25V): 2 ns. See Figure A.
• Input and output timing reference levels: 1.25V.
V
L
= V
DDQ
/2
Thevenin equivalent:
353
Ω
/1538
Ω
5 pF*
319
Ω
/1667
Ω
D
OUT
GND
Figure C: Output load(B)
*including scope
and jig capacitance
+2.5V
®
AS7C251MNTD18A
12/23/04, v.2.2 Alliance Semiconductor P. 16 of 18
Package dimensions
100-pin quad flat pack (TQFP)
TQFP
Min Max
A1 0.05 0.15
A2 1.35 1.45
b0.22 0.38
c0.09 0.20
D13.90 14.10
E19.90 20.10
e0.65 nominal
Hd 15.85 16.15
He 21.80 22.20
L0.45 0.75
L1 1.00 nominal
α0° 7°
Dimensions in millimeters
A1 A2
L1
L
c
He E
Hd
D
b
e
α
®
AS7C251MNTD18A
12/23/04, v.2.2 Alliance Semiconductor P. 17 of 18
Ordering information
Note:
Add suffix ‘N’ to the above part number for Lead Free Parts (Ex.
AS7C251MNTD18A-166TQCN)
Part numbering guide
1. Alliance Semiconductor SRAM prefix
2. Operating voltage: 25 = 2.5V
3. Organization:
1M
4. NTD™ = No Turn-Around Delay. Pipelined mode
5. Organization: 18 = x 18
6. Production version: A = first production version
7. Clock speed (MHz)
8. Package type: TQ = TQFP
9. Operating temperature: C = commercial (
0
°
C to 70
°
C); I = industrial (
-40
°
C to 85
°
C)
10. N = Lead free part
Package &Width –166 MHz –133 MHz
TQFP x18 AS7C251MNTD18A-166TQC AS7C251MNTD18A-133TQC
AS7C251MNTD18A-166TQI AS7C251MNTD18A-133TQI
AS7C 25 1M NTD 18 A–XXX TQ C/I X
1
23
45678
910
®
AS7C251MNTD18A
Alliance Semiconductor Corporation
2575, Augustine Drive,
Santa Clara, CA 95054
Tel: 408 - 855 - 4900
Fax: 408 - 855 - 4999
www.alsc.com
Copyright © Alliance Semiconductor
All Rights Reserved
Part Number: AS7C251MNTD18A
Document Version: v.2.2
© Copyright 2003 Alliance Semiconductor Corporation. All rights reserved. Our three-point logo, our name and Intelliwatt are trademarks or registered trademarks of
Alliance. All other brand and product names may be the trademarks of their respective companies. Alliance reserves the right to make changes to this document and its
products at any time without notice. Alliance assumes no responsibility for any errors that may appear in this document. The data contained herein represents Alliance's best
data and/or estimates at the time of issuance. Alliance reserves the right to change or correct this data at any time, without notice. If the product described herein is under
development, significant changes to these specifications are possible. The information in this product data sheet is intended to be general descriptive information for
potential customers and users, and is not intended to operate as, or provide, any guarantee or warrantee to any user or customer. Alliance does not assume any responsibility
or liability arising out of the application or use of any product described herein, and disclaims any express or implied warranties related to the sale and/or use of Alliance
products including liability or warranties related to fitness for a particular purpose, merchantability, or infringement of any intellectual property rights, except as express
agreed to in Alliance's Terms and Conditions of Sale (which are available from Alliance). All sales of Alliance products are made exclusively according to Alliance's Terms
and Conditions of Sale. The purchase of products from Alliance does not convey a license under any patent rights, copyrights; mask works rights, trademarks, or any other
intellectual property rights of Alliance or third parties. Alliance does not authorize its products for use as critical components in life-supporting systems where a malfunction
or failure may reasonably be expected to result in significant injury to the user, and the inclusion of Alliance products in such life-supporting systems implies that the
manufacturer assumes all risk of such use and agrees to indemnify Alliance against all claims arising from such use.
®
