March 2004 AS7C31026B (R) 3.3 V 64K X 16 CMOS SRAM Features * Industrial and commercial versions * Organization: 65,536 words x 16 bits * Center power and ground pins for low noise * High speed - 10/12/15/20 ns address access time - 5, 6, 7, 8 ns output enable access time * Low power consumption: ACTIVE * Easy memory expansion with CE, OE inputs * TTL-compatible, three-state I/O * JEDEC standard packaging - 44-pin 400 mil SOJ - 44-pin TSOP 2-400 * ESD protection 2000 volts * Latch-up current 200 mA - 288 mW / max @ 10 ns * Low power consumption: STANDBY - 18 mW / max CMOS I/O * 6 T 0.18 u CMOS technology Logic block diagram Pin arrangement A2 A3 A4 A5 A6 44-Pin SOJ (400 mil), TSOP 2 VCC 64 K x 16 Array GND A4 A3 A2 A1 A0 CE I/O0 I/O1 I/O2 I/O3 VCC GND I/O4 I/O5 I/O6 I/O7 WE A15 A14 A13 A12 NC A7 I/O buffer A15 A14 A11 A13 UB OE LB CE A12 A9 Column decoder A8 WE Control circuit A10 I/O0-I/O7 I/O8-I/O15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 AS7C31026B A1 Row decoder A0 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 A5 A6 A7 OE UB LB I/O15 I/O14 I/O13 I/O12 GND VCC I/O11 I/O10 I/O9 I/O8 NC A8 A9 A10 A11 NC Selection guide -10 -12 -15 -20 Unit Maximum address access time 10 12 15 20 ns Maximum output enable access time 5 6 7 8 ns Maximum operating current 80 75 70 65 mA Maximum CMOS standby current 5 5 5 5 mA 3/26/04, v 1.3 Alliance Semiconductor P. 1 of 10 Copyright (c) Alliance Semiconductor. All rights reserved. AS7C31026B (R) Functional description The AS7C31026B is a high-performance CMOS 1,048,576-bit Static Random Access Memory (SRAM) device organized as 65,536 words x 16 bits. It is designed for memory applications where fast data access, low power, and simple interfacing are desired. Equal address access and cycle times (tAA, tRC, tWC) of 10/12/15/20 ns with output enable access times (tOE) of 5, 6, 7, 8 ns are ideal for high-performance applications. When CE is high, the device enters standby mode. A write cycle is accomplished by asserting write enable (WE) and chip enable (CE). Data on the input pins I/O0 through I/O15 is written on the rising edge of WE (write cycle 1) or CE (write cycle 2). To avoid bus contention, external devices should drive I/O pins only after outputs have been disabled with output enable (OE) or write enable (WE). A read cycle is accomplished by asserting output enable (OE) and chip enable (CE) with write enable (WE) high. The chips drive I/O pins with the data word referenced by the input address. When either chip enable or output enable is inactive or write enable is active, output drivers stay in high-impedance mode. The device provides multiple center power and ground pins, and separate byte enable controls, allowing individual bytes to be written and read. LB controls the lower bits, I/O0 through I/O7, and UB controls the higher bits, I/O8 through I/O15. All chip inputs and outputs are TTL-compatible, and operation is from a single 3.3 V supply. The device is packaged in common industry standard packages. Absolute maximum ratings Parameter Symbol Min Max Unit Voltage on VCC relative to GND Vt1 -0.50 +5.0 V Voltage on any pin relative to GND Vt2 -0.50 VCC +0.50 V Power dissipation PD - 1.0 W Storage temperature (plastic) Tstg -65 +150 C Ambient temperature with VCC applied Tbias -55 +125 C DC current into outputs (low) IOUT - 20 mA Note: Stresses greater than those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions outside those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Truth table CE WE OE LB UB I/O0-I/O7 I/O8-I/O15 Mode H X X X X High Z High Z Standby (ISB), ISBI) L H L L H DOUT High Z Read I/O0-I/O7 (ICC) L H L H L High Z DOUT Read I/O8-I/O15 (ICC) L H L L L DOUT DOUT Read I/O0-I/O15 (ICC) L L X L L DIN DIN Write I/O0-I/O15 (ICC) L L X L H DIN High Z Write I/O0-I/O7 (ICC) L L X H L High Z DIN Write I/O8-I/O15 (ICC) L L H X H X X H X H High Z High Z Output disable (ICC) Key: H = high, L = low, X = don't care. 3/26/04, v 1.3 Alliance Semiconductor P. 2 of 10 AS7C31026B (R) Recommended operating conditions Parameter Symbol Min Nominal Max Unit Supply voltage VCC 3.0 3.3 3.6 V Input voltage VIH 2.0 - VCC + 0.5 V VIL -0.5 - 0.8 commercial Ambient operating temperature industrial TA 0 TA - -40 - V 70 o C 85 o C VIL = -1.0V for pulse width less than 5ns VIH = VCC + 1.5V for pulse width less than 5ns DC operating characteristics (over the operating range)1 -10 Parameter -12 Sym Test conditions Input leakage current | ILI | VCC = Max VIN = GND to VCC - 1 Output leakage current | ILO | VCC = Max CE = VIH, VOUT = GND to VCC - ICC VCC = Max, CE VIL, IOUT = 0mA f = fMax ISB Operating power supply current Standby power supply current Output voltage Min Max Min -15 -20 Max Min Max Min Max Unit - 1 - 1 - 1 A 1 - 1 - 1 - 1 A - 80 - 75 - 70 - 65 mA VCC = Max, CE VIH, f = fMax - 30 - 25 - 20 - 20 mA ISB1 VCC = Max, CE VCC-0.2 V, VIN 0.2 V or VIN VCC-0.2 V, f = 0 - 5 - 5 - 5 - 5 mA VOL IOL = 8 mA, VCC = Min - 0.4 - 0.4 - 0.4 - 0.4 V VOH IOH = -4 mA, VCC = Min 2.4 - 2.4 - 2.4 - 2.4 - V Capacitance (f = 1MHz, Ta = 25 C, VCC = NOMINAL)2 Parameter Symbol Signals Test conditions Max Unit Input capacitance CIN A, CE, WE, OE, LB, UB VIN = 0 V 5 pF I/O capacitance CI/O I/O VIN = VOUT = 0 V 7 pF 3/26/04, v 1.3 Alliance Semiconductor P. 3 of 10 AS7C31026B (R) Read cycle (over the operating range)3,9 -10 Parameter -12 -15 -20 Symbol Min Max Min Max Min Max Min Max Unit Notes Read cycle time tRC 10 - 12 - 15 - 20 - ns Address access time tAA - 10 - 12 - 15 - 20 ns 3 Chip enable (CE) access time tACE - 10 - 12 - 15 - 20 ns 3 Output enable (OE) access time tOE - 5 - 6 - 7 - 8 ns Output hold from address change tOH 3 - 3 - 3 - 3 - ns 5 CE low to output in low Z tCLZ 3 - 3 - 3 - 3 - ns 4, 5 CE high to output in high Z tCHZ - 3 - 3 - 4 - 5 ns 4, 5 OE low to output in low Z tOLZ 0 - 0 - 0 - 0 - ns 4, 5 Byte select access time tBA - 5 - 6 - 7 - 8 ns Byte select Low to low Z tBLZ 0 - 0 - 0 - 0 - ns 4, 5 Byte select High to high Z tBHZ - 5 - 6 - 6 - 8 ns 4, 5 OE high to output in high Z tOHZ - 5 - 6 - 7 - 8 ns 4, 5 Power up time tPU 0 - 0 - 0 - 0 - ns 4, 5 Power down time tPD - 10 - 12 - 15 20 ns 4, 5 Key to switching waveforms Rising input Falling input Undefined output/don't care Read waveform 1 (address controlled)3,6,7,9 tRC Address DataOUT 3/26/04, v 1.3 tOH Previous data valid tAA tOH Data valid Alliance Semiconductor P. 4 of 10 AS7C31026B (R) Read waveform 2 (OE, CE, UB, LB controlled)3,6,8,9 tRC Address tAA OE tOE tOLZ tOH CE tOHZ tACE tLZ tHZ LB, UB tBA tBLZ tBHZ DataIN Data valid Write cycle (over the operating range) 11 -10 Parameter -12 -15 Symbol Min Max Max Min Max Unit Write cycle time tWC 10 - 12 - 15 - 20 - ns Chip enable (CE) to write end tCW 8 - 9 - 10 - 12 - ns Address setup to write end tAW 8 - 9 - 10 - 12 - ns Address setup time tAS 0 - 0 - 0 - 0 - ns Write pulse width tWP 7 - 8 - 9 - 12 - ns Write recovery time tWR 0 - 0 - 0 - 0 - ns Address hold from end of write tAH 0 - 0 - 0 - 0 - ns Data valid to write end tDW 5 - 6 - 8 - 10 - ns Data hold time tDH 0 - 0 - 0 - 0 - ns 5 Write enable to output in high Z tWZ - 5 - 6 - 7 - 8 ns 4, 5 Output active from write end tOW 1 - 1 - 1 - 2 - ns 4, 5 Byte select low to end of write tBW 7 - 8 - 9 - 9 - ns 3/26/04, v 1.3 Min Max Min -20 Alliance Semiconductor Notes P. 5 of 10 AS7C31026B (R) Write waveform 1 (WE controlled)10,11 tWC tAH Address tWR tCW CE tBW LB, UB tAW tAS tWP WE tDW DataIN tDH Data valid tWZ DataOUT tOW Data undefined high Z Write waveform 2 (CE controlled)10,11 tWC tAH Address tAS CE tWR tCW tAW tBW LB, UB tWP WE tDH tDW Data valid DataIN tCLZ DataOUT 3/26/04, v 1.3 high Z tWZ Data undefined Alliance Semiconductor tOW high Z P. 6 of 10 AS7C31026B (R) AC test conditions - - - - Output load: see Figure B. Input pulse level: GND to 3.0 V. See Figure A. Input rise and fall times: 2 ns. See Figure A. Input and output timing reference levels: 1.5 Thevenin Equivalent: 168 DOUT +1.728 V +3.3 V 320 +3.0 V GND DOUT 90% 10% 255 90% 2 ns 10% C13 GND Figure B: 3.3 V Output load Figure A: Input pulse Notes 1 2 3 4 5 6 7 8 9 10 11 12 13 During VCC power-up, a pull-up resistor to VCC on CE is required to meet ISB specification. This parameter is sampled, but not 100% tested. For test conditions, see AC Test Conditions, Figures A and B. These parameters are specified with CL = 5 pF, as in Figures B. Transition is measured 500 mV from steady-state voltage. This parameter is guaranteed, but not tested. WE is high for read cycle. CE and OE are low for read cycle. Address is valid prior to or coincident with CE transition low. All read cycle timings are referenced from the last valid address to the first transitioning address. N/A All write cycle timings are referenced from the last valid address to the first transitioning address. Not applicable. C = 30 pF, except all high Z and low Z parameters where C = 5 pF. 3/26/04, v 1.3 Alliance Semiconductor P. 7 of 10 AS7C31026B (R) Package dimensions c 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 44-pin TSOP 2 Min (mm) E He 44-pin TSOP 2 A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 D l A2 A 0-5 A1 e b Max (mm) 1.2 A1 0.05 0.15 A2 0.95 1.05 b 0.30 0.45 c 0.120 0.21 D 18.31 18.52 E 10.06 10.26 He 11.68 11.94 e l 0.80 (typical) 0.40 0.60 44-pin SOJ 400 mil D e Min (in) Max (in) 44-pin SOJ E1 E2 Pin 1 c B A2 A A1 b Seating plane E A 0.128 0.148 A1 0.025 - A2 0.105 0.115 B 0.026 0.032 b 0.015 0.020 c 0.007 0.013 D 1.120 1.130 E E1 0.395 0.405 E2 0.435 0.445 e 3/26/04, v 1.3 Alliance Semiconductor 0.370 NOM 0.050 NOM P. 8 of 10 AS7C31026B (R) Ordering codes Package\Access time Volt/Temp 10 ns 3.3 V commercial AS7C31026B-10JC Plastic SOJ, 400 mil 3.3 V industrial TSOP 2, 10.2 x 18.4 mm 12 ns 15 ns 20 ns AS7C31026B-12JC AS7C31026B-15JC AS7C31026B-20JC AS7C31026B-10JI AS7C31026B-12JI AS7C31026B-15JI AS7C31026B-20JI 3.3 V commercial AS7C31026B-10TC AS7C31026B-12TC AS7C31026B-15TC AS7C31026B-20TC AS7C31026B-12TI AS7C31026B-15TI AS7C31026B-20TI 3.3 V industrial AS7C31026B-10TI Note: Add suffix `N' to the above part number for lead free parts (Ex. AS7C31026B-10JCN) Part numbering system AS7C X SRAM prefix Voltage: 1026B -XX Device Access 3 = 3.3 V CMOS number time 3/26/04, v 1.3 X X X Package: Temperature range: N=Lead Free C = commercial: 0 C to 70 C J = SOJ 400 mil Part T = TSOP 2, 10.2 x 18.4 mm I = industrial: -40 C to 85 C Alliance Semiconductor P. 9 of 10 AS7C31026B (R) (R) Alliance Semiconductor Corporation Copyright (c) Alliance Semiconductor 2575, Augustine Drive, All Rights Reserved Santa Clara, CA 95054 Part Number: AS7C31026B Tel: 408 - 855 - 4900 Document Version: v 1.3 Fax: 408 - 855 - 4999 www.alsc.com (c) Copyright 2003 Alliance Semiconductor Corporation. All rights reserved. Our three-point logo, our name and Intelliwatt are trademarks or registered trademarks of Alliance. All other brand and product names may be the trademarks of their respective companies. Alliance reserves the right to make changes to this document and its products at any time without notice. Alliance assumes no responsibility for any errors that may appear in this document. The data contained herein represents Alliance's best data and/or estimates at the time of issuance. Alliance reserves the right to change or correct this data at any time, without notice. If the product described herein is under development, significant changes to these specifications are possible. The information in this product data sheet is intended to be general descriptive information for potential customers and users, and is not intended to operate as, or provide, any guarantee or warrantee to any user or customer. Alliance does not assume any responsibility or liability arising out of the application or use of any product described herein, and disclaims any express or implied warranties related to the sale and/or use of Alliance products including liability or warranties related to fitness for a particular purpose, merchantability, or infringement of any intellectual property rights, except as express agreed to in Alliance's Terms and Conditions of Sale (which are available from Alliance). All sales of Alliance products are made exclusively according to Alliance's Terms and Conditions of Sale. The purchase of products from Alliance does not convey a license under any patent rights, copyrights; mask works rights, trademarks, or any other intellectual property rights of Alliance or third parties. Alliance does not authorize its products for use as critical components in life-supporting systems where a malfunction or failure may reasonably be expected to result in significant injury to the user, and the inclusion of Alliance products in such life-supporting systems implies that the manufacturer assumes all risk of such use and agrees to indemnify Alliance against all claims arising from such use.