LM20EP Enhanced Plastic 2.4V, 10A, SC70, micro SMD Temperature Sensor General Description Features The LM20EP is a precision analog output CMOS integratedcircuit temperature sensor that operates over a -55C to +130C temperature range. The power supply operating range is +2.4 V to +5.5 V. The transfer function of LM20EP is predominately linear, yet has a slight predictable parabolic curvature. The accuracy of the LM20EP when specified to a parabolic transfer function is 1.5C at an ambient temperature of +30C. The temperature error increases linearly and reaches a maximum of 2.5C at the temperature range extremes. The temperature range is affected by the power supply voltage. At a power supply voltage of 2.7 V to 5.5 V the temperature range extremes are +130C and -55C. Decreasing the power supply voltage to 2.4 V changes the negative extreme to -30C, while the positive remains at +130C. The LM20EP's quiescent current is less than 10 A. Therefore, self-heating is less than 0.02C in still air. Shutdown capability for the LM20EP is intrinsic because its inherent low power consumption allows it to be powered directly from the output of many logic gates or does not necessitate shutdown at all. ENHANCED PLASTIC * Extended Temperature Performance of -55C to +130C * Baseline Control - Single Fab & Assembly Site n n n n * * * * Rated for full -55C to +130C range Available in an SC70 and a micro SMD package Predictable curvature error Suitable for remote applications Key Specifications j Accuracy at +130C & -55C 1.5 to 4 C (max) 2.5 to 5 C (max) j Power Supply Voltage Range +2.4V to +5.5V j Accuracy at +30C j Current Drain 10 A (max) j Nonlinearity 0.4 % (typ) j Output Impedance 160 (max) j Load Regulation 0 A < IL < +16 A -2.5 mV (max) Applications n Battery Management n Selected Military Applications n Selected Avionics Applications Process Change Notification (PCN) Qualification & Reliability Data Solder (PbSn) Lead Finish is standard Enhanced Diminishing Manufacturing Sources (DMS) Support Ordering Information PART NUMBER VID PART NUMBER NS PACKAGE NUMBER (Note 3) LM20CIM7EP V62/04728-01 MAA05A (Notes 1, 2) TBD TBD Note 1: For the following (Enhanced Plastic) version, check for availability: LM20SIBPEP, LM20SIBPXEP, LM20BIM7EP, LM20BIM7XEP, LM20CIM7XEP, LM20SITLEP, LM20SITLXEP. Parts listed with an "X" are provided in Tape & Reel and parts without an "X" are in Rails. Note 2: FOR ADDITIONAL ORDERING AND PRODUCT INFORMATION, PLEASE VISIT THE ENHANCED PLASTIC WEB SITE AT: www.national.com/ mil Note 3: Refer to package details under Physical Dimensions (c) 2004 National Semiconductor Corporation DS200999 www.national.com LM20EP Enhanced Plastic 2.4V, 10A, SC70, micro SMD Temperature Sensor May 2004 LM20EP Enhanced Plastic Typical Application Full-Range Celsius (Centigrade) Temperature Sensor (-55C to +130C) Operating from a Single Li-Ion Battery Cell Output Voltage vs Temperature 20099902 VO = (-3.88x10-6xT2) + (-1.15x10-2xT) + 1.8639 20099924 where: T is temperature, and VO is the measured output voltage of the LM20EP. Temperature (T) Typical VO +130C +303 mV +100C +675 mV +80C +919 mV +30C +1515 mV +25C +1574 mV 0C +1863.9 mV -30C +2205 mV -40C +2318 mV -55C +2485 mV Connection Diagrams SC70-5 micro SMD 20099901 Note: 20099932 - GND (pin 2) may be grounded or left floating. For optimum thermal conductivity to the pc board ground plane pin 2 should be grounded. Note: - NC (pin 1) should be left floating or grounded. Other signal traces should not be connected to this pin. - Pin numbers are referenced to the package marking text orientation. - Reference JEDEC Registration MO-211, variation BA - The actual physical placement of package marking will vary slightly from part to part. The package marking will designate the date code and will vary considerably. Package marking does not correlate to device type in any way. Top View See NS Package Number MAA05A Top View See NS Package Number BPA04DDC and TLA04ZZA www.national.com 2 Vapor Phase (60 seconds) +215C If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Infrared (15 seconds) +220C Supply Voltage +6.5V to -0.2V Output Voltage (V+ + 0.6 V) to -0.6 V Output Current Operating Ratings(Note 4) LM20BEP, LM20CEP with 2.4 V V+ 2.7 V 10 mA Input Current at any pin (Note 5) 5 mA Storage Temperature -65C to +150C Maximum Junction Temperature (TJMAX) TMIN TA TMAX Specified Temperature Range: LM20BEP, LM20CEP with 2.7 V V+ 5.5 V -55C TA +130C LM20SEP with 2.4 V V+ 5.5 V -30C TA +125C LM20SEP with 2.7 V V+ 5.5 V +150C ESD Susceptibility (Note 6) : -30C TA +130C -40C TA +125C + Human Body Model Supply Voltage Range (V ) 2500 V Machine Model +2.4 V to +5.5 V Thermal Resistance, JA(Note 8) SC-70 micro SMD 250 V Lead Temperature SC-70 Package (Note 7) : 415C/W 340C/W Electrical Characteristics Unless otherwise noted, these specifications apply for V+ = +2.7 VDC. Boldface limits apply for TA = TJ = TMIN to TMAX ; all other limits TA = TJ = 25C; Unless otherwise noted. Parameter Temperature to Voltage Error VO = (-3.88x10-6xT2) + (-1.15x10-2xT) + 1.8639V (Note 11) Conditions Typical (Note 9) TA = +25C to +30C TA = +130C TA = +125C TA = +100C TA = +85C TA = +80C TA = 0C TA = -30C TA = -40C TA = -55C Output Voltage at 0C LM20BEP LM20CEP LM20SEP Limits Limits Limits (Note 10) (Note 10) (Note 10) 1.5 2.5 2.5 2.2 2.1 2.0 1.9 2.2 2.3 2.5 4.0 5.0 5.0 4.7 4.6 4.5 4.4 4.7 4.8 5.0 2.5 Units (Limit) C (max) C (max) 3.5 3.2 3.1 3.0 2.9 3.3 3.5 C (max) C (max) C (max) C (max) C (max) C (min) C (max) C (max) +1.8639 V C Non-Linearity (Note 12) -20C TA +80C 1.0 0.4 Sensor Gain (Temperature Sensitivity or Average Slope) to equation: VO=-11.77 mV/CxT+1.860V -30C TA +100C -11.77 Output Impedance Variance from Curve % -11.4 -12.2 -11.0 -12.6 -11.0 -12.6 mV/C (min) mV/C (max) 0 A IL +16 A (Notes 14, 15) 160 160 160 (max) Load Regulation(Note 13) 0 A IL +16 A (Notes 14, 15) -2.5 -2.5 -2.5 mV (max) Line Regulation +2. 4 V V+ +5.0V +3.3 +3.7 +3.7 mV/V (max) +5.0 V V+ +5.5 V +11 +11 +11 mV (max) A (max) Quiescent Current Change of Quiescent Current +2. 4V V +5.0V 4.5 7 7 7 +5.0V V+ +5.5V 4.5 9 9 9 A (max) +2. 4V V+ +5.0V 4.5 10 10 10 A (max) +2. 4 V V+ +5.5V +0.7 A -11 nA/C + Temperature Coefficient of 3 www.national.com LM20EP Enhanced Plastic Absolute Maximum Ratings (Note 4) LM20EP Enhanced Plastic Electrical Characteristics (Continued) Unless otherwise noted, these specifications apply for V+ = +2.7 VDC. Boldface limits apply for TA = TJ = TMIN to TMAX ; all other limits TA = TJ = 25C; Unless otherwise noted. Parameter Conditions Typical (Note 9) LM20BEP LM20CEP LM20SEP Limits Limits Limits (Note 10) (Note 10) (Note 10) Units (Limit) Quiescent Current Shutdown Current V+ +0.8 V 0.02 A Note 4: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 5: When the input voltage (VI) at any pin exceeds power supplies (VI < GND or VI > V+), the current at that pin should be limited to 5 mA. Note 6: The human body model is a 100 pF capacitor discharged through a 1.5 k resistor into each pin. The machine model is a 200 pF capacitor discharged directly into each pin. Note 7: See AN-450 "Surface Mounting Methods and Their Effect on Product Reliability" or the section titled "Surface Mount" found in any post 1986 National Semiconductor Linear Data Book for other methods of soldering surface mount devices. Note 8: The junction to ambient thermal resistance (JA) is specified without a heat sink in still air using the printed circuit board layout shown in Figure 1. Note 9: Typicals are at TJ = TA = 25C and represent most likely parametric norm. Note 10: Limits are guaranteed to National's AOQL (Average Outgoing Quality Level). Note 11: Accuracy is defined as the error between the measured and calculated output voltage at the specified conditions of voltage, current, and temperature (expressed inC). Note 12: Non-Linearity is defined as the deviation of the calculated output-voltage-versus-temperature curve from the best-fit straight line, over the temperature range specified. Note 13: Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output due to heating effects can be computed by multiplying the internal dissipation by the thermal resistance. Note 14: Negative currents are flowing into the LM20EP. Positive currents are flowing out of the LM20EP. Using this convention the LM20EP can at most sink -1 A and source +16 A. Note 15: Load regulation or output impedance specifications apply over the supply voltage range of +2.4V to +5.5V. Note 16: Line regulation is calculated by subtracting the output voltage at the highest supply input voltage from the output voltage at the lowest supply input voltage. Typical Performance Characteristic Temperature Error vs Temperature 20099925 PCB Layouts Used for Thermal Measurements 20099930 20099929 b) Layout used for measurements with small heat hink. a) Layout used for no heat sink measurements. FIGURE 1. PCB Lyouts used for thermal measurements. www.national.com 4 The LM20EP's transfer function can be described in different ways with varying levels of precision. A simple linear transfer function, with good accuracy near 25C, is VO= -11.69 mV/C x T + 1.8663 V T=35C and m = -11.77 mV/C The offset of the linear transfer function can be calculated using the following equation: b = (VOP(Tmax) + VOP(T) + m x (Tmax+T))/2 Over the full operating temperature range of -55C to +130C, best accuracy can be obtained by using the parabolic transfer function VO = (-3.88x10-6xT2) + (-1.15x10-2xT) + 1.8639 , where: * VOP(Tmax) is the calculated output voltage at Tmax using the parabolic transfer function for VO * VOP(T) is the calculated output voltage at T using the parabolic transfer function for VO. Using this procedure the best fit linear transfer function for many popular temperature ranges was calculated in Figure 2. As shown in Figure 2 the error that is introduced by the linear transfer function increases with wider temperature ranges. solving for T: A linear transfer function can be used over a limited temperature range by calculating a slope and offset that give best results over that range. A linear transfer function can be calculated from the parabolic transfer function of the LM20EP. The slope of the linear transfer function can be calculated using the following equation: m = -7.76 x 10-6x T - 0.0115, Temperature Range Tmin (C) Tmax (C) Linear Equation VO= Maximum Deviation of Linear Equation from Parabolic Equation (C) 1.41 0.93 0.70 0.65 0.23 0.004 0.004 -55 +130 -11.79 mV/C x T + 1.8528 V -40 +110 -11.77 mV/C x T + 1.8577 V -30 +100 -11.77 mV/C x T + 1.8605 V -40 +85 -11.67 mV/C x T + 1.8583 V -10 +65 -11.71 mV/C x T + 1.8641 V +35 +45 -11.81 mV/C x T + 1.8701 V +20 +30 -11.69 mV/C x T + 1.8663 V FIGURE 2. First order equations optimized for different temperature ranges. insulated and dry, to avoid leakage and corrosion. This is especially true if the circuit may operate at cold temperatures where condensation can occur. Printed-circuit coatings and varnishes such as Humiseal and epoxy paints or dips are often used to ensure that moisture cannot corrode the LM20EP or its connections. The thermal resistance junction to ambient (JA) is the parameter used to calculate the rise of a device junction temperature due to its power dissipation. For the LM20EP the equation used to calculate the rise in the die temperature is as follows: TJ = TA + JA [(V+ IQ) + (V+ - VO) IL] where IQ is the quiescent current and ILis the load current on the output. Since the LM20EP's junction temperature is the actual temperature being measured care should be taken to minimize the load current that the LM20EP is required to drive. The tables shown in Figure 3 summarize the rise in die temperature of the LM20EP without any loading, and the thermal resistance for different conditions. Mounting The LM20EP can be applied easily in the same way as other integrated-circuit temperature sensors. It can be glued or cemented to a surface. The temperature that the LM20EP is sensing will be within about +0.02C of the surface temperature to which the LM20EP's leads are attached to. This presumes that the ambient air temperature is almost the same as the surface temperature; if the air temperature were much higher or lower than the surface temperature, the actual temperature measured would be at an intermediate temperature between the surface temperature and the air temperature. To ensure good thermal conductivity the backside of the LM20EP die is directly attached to the pin 2 GND pin. The tempertures of the lands and traces to the other leads of the LM20EP will also affect the temperature that is being sensed. Alternatively, the LM20EP can be mounted inside a sealedend metal tube, and can then be dipped into a bath or screwed into a threaded hole in a tank. As with any IC, the LM20EP and accompanying wiring and circuits must be kept 5 www.national.com LM20EP Enhanced Plastic where T is the middle of the temperature range of interest and m is in V/C. For example for the temperature range of Tmin=-30 to Tmax=+100C: LM20EP Transfer Function LM20EP Enhanced Plastic Mounting Still air (Continued) SC70-5 SC70-5 SC70-5 SC70-5 no heat sink small heat sink no heat sink small heat sink JA TJ - T A JA T J - TA JA TJ - T A JA (C/W) (C) (C/W) (C) (C/W) (C) (C/W) (C) 412 0.2 350 0.19 312 0.17 266 0.15 Moving air TJ - T A See Figure 1 for PCB layout samples. micro SMD micro SMD micro SMD micro SMD no heat sink small heat fin no heat sink small heat fin JA Still air TJ - T A JA (C/W) (C) (C/W) (C) 340 0.18 TBD TBD JA T J - TA Moving air TJ - T A JA (C/W) (C) (C/W) (C) TBD TBD TBD TBD TJ - T A FIGURE 3. Temperature Rise of LM20EP Due to Self-Heating and Thermal Resistance (JA) of the LM20EP is much slower, the overall response time of the LM20EP will not be significantly affected. Capacitive Loads The LM20EP handles capacitive loading well. Without any precautions, the LM20EP can drive any capacitive load less than 300 pF as shown in Figure 4. Over the specified temperature range the LM20EP has a maximum output impedance of 160 . In an extremely noisy environment it may be necessary to add some filtering to minimize noise pickup. It is recommended that 0.1 F be added from V+ to GND to bypass the power supply voltage, as shown in Figure 5. In a noisy environment it may even be necessary to add a capacitor from the output to ground with a series resistor as shown in Figure 5. A 1 F output capacitor with the 160 maximum output impedance and a 200 series resistor will form a 442 Hz lowpass filter. Since the thermal time constant 20099915 FIGURE 4. LM20EP No Decoupling Required for Capacitive Loads Less than 300 pF. R () C (F) 200 1 470 0.1 680 0.01 1k 0.001 20099916 20099933 FIGURE 5. LM20EP with Filter for Noisy Environment and Capacitive Loading greater than 300 pF. Either placement of resistor as shown above is just as effective. www.national.com 6 Exposing the LM20EP micro SMD package to bright sunlight may cause the output reading of the LM20EP to drop by 1.5V. In a normal office environment of fluorescent lighting the output voltage is minimally affected (less than a millivolt Applications Circuits 20099918 FIGURE 6. Centigrade Thermostat 20099919 FIGURE 7. Conserving Power Dissipation with Shutdown 20099928 Most CMOS ADCs found in ASICs have a sampled data comparator input structure that is notorious for causing grief to analog output devices such as the LM20EP and many op amps. The cause of this grief is the requirement of instantaneous charge of the input sampling capacitor in the ADC. This requirement is easily accommodated by the addition of a capacitor. Since not all ADCs have identical input stages, the charge requirements will vary necessitating a different value of compensating capacitor. This ADC is shown as an example only. If a digital output temperature is required please refer to devices such as the LM74. FIGURE 8. Suggested Connection to a Sampling Analog to Digital Converter Input Stage 7 www.national.com LM20EP Enhanced Plastic drop). In either case it is recommended that the LM20EP micro SMD be placed inside an enclosure of some type that minimizes its light exposure. Most chassis provide more than ample protection. The LM20EP does not sustain permanent damage from light exposure. Removing the light source will cause LM20EP's output voltage to recover to the proper value. LM20EP micro SMD Light Sensitivity LM20EP Enhanced Plastic Physical Dimensions inches (millimeters) unless otherwise noted 5-Lead SC70 Molded Package NS Package Number MAA05A 4-Bump micro SMD Ball Grid Array Package (Small Bump) NS Package Number BPA04DDC The following dimensions apply to the BPA04DDC package shown above: X1=X2 = 853m 30m, X3= 900m 50m www.national.com 8 inches (millimeters) unless otherwise noted (Continued) 4-Bump micro SMD Ball Grid Array Package (Large Bump) NS Package Number TLA04ZZA The following dimensions apply to the TLA04ZZA package shown above: X1=X2 = 963m 30m, X3= 600m 75m LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. LM20EP Enhanced Plastic 2.4V, 10A, SC70, micro SMD Temperature Sensor Physical Dimensions