Product Folder Sample & Buy Support & Community Tools & Software Technical Documents LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 LMV3xx-N/-Q1 Single, Dual, and Quad General Purpose, Low-Voltage, Rail-to-Rail Output Operational Amplifiers 1 Features * 1 * * * * * * * * * * * + 3 Description - (For V = 5 V and V = 0 V, Unless Otherwise Specified) LMV321-N, LMV358-N, and LMV324-N are available in Automotive AEC-Q100 Grade 1 and 3 versions Ensured 2.7-V and 5-V Performance No Crossover Distortion Industrial Temperature Range -40C to +125C Gain-Bandwidth Product 1 MHz Low Supply Current LMV321-N 130 A LMV358-N 210 A LMV324-N 410 A Rail-to-Rail Output Swing At 10 k V+- 10 mV & V-+ 65 mV VCM Range -0.2 V to V+- 0.8 V The LMV358-N and LMV324-N are low-voltage (2.7 V to 5.5 V) versions of the dual and quad commodity op amps LM358 and LM324 (5 V to 30 V). The LMV321N is the single channel version. The LMV321-N, LMV358-N, and LMV324-N are the most costeffective solutions for applications where low-voltage operation, space efficiency, and low price are important. They offer specifications that meet or exceed the familiar LM358 and LM324. The LMV321N, LMV358-N, and LMV324-N have rail-to-rail output swing capability and the input common-mode voltage range includes ground. They all exhibit excellent speed to power ratio, achieving 1 MHz of bandwidth and 1-V/s slew rate with low supply current. Device Information(1) PART NUMBER LMV321-N LMV321-N-Q1 2 Applications * * * Active Filters General Purpose Low Voltage Applications General Purpose Portable Devices LMV324-N LMV324-N-Q1 LMV358-N LMV358-N-Q1 PACKAGE BODY SIZE (NOM) SOT-23 (5) 2.90 mm x 1.60 mm SC70 (5) 2.00 mm x 1.25 mm SOT-23 (5) 2.90 mm x 1.60 mm SOIC (14) 8.65 mm x 3.91 mm TSSOP (14) 5.00 mm x 4.40 mm SOIC (14) 8.65 mm x 3.91 mm TSSOP (14) 5.00 mm x 4.40 mm SOIC (8) 4.90 mm x 3.91 mm VSSOP (8) 3.00 mm x 3.00 mm SOIC (8) 4.90 mm x 3.91 mm VSSOP (8) 3.00 mm x 3.00 mm (1) For all available packages, see the orderable addendum at the end of the datasheet. Gain and Phase vs. Capacitive Load Output Voltage Swing vs. Supply Voltage 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 www.ti.com Table of Contents 1 2 3 4 5 6 7 8 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Description (Continued) ........................................ Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 3 4 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 7.10 4 4 4 4 5 5 5 6 7 8 Absolute Maximum Ratings ...................................... ESD Ratings - Commercial ....................................... ESD Ratings - Automotive ........................................ Recommended Operating Conditions....................... Thermal Information .................................................. 2.7-V DC Electrical Characteristics........................... 2.7-V AC Electrical Characteristics ........................... 5-V DC Electrical Characteristics.............................. 5-V AC Electrical Characteristics .............................. Typical Characteristics ............................................ Detailed Description ............................................ 16 8.1 8.2 8.3 8.4 9 Overview ................................................................. Functional Block Diagram ....................................... Feature Description................................................. Device Functional Modes........................................ 16 17 17 19 Application and Implementation ........................ 20 9.1 Application Information............................................ 20 9.2 Typical Applications ................................................ 20 10 Power Supply Recommendations ..................... 32 11 Layout................................................................... 32 11.1 Layout Guidelines ................................................. 32 11.2 Layout Example .................................................... 33 12 Device and Documentation Support ................. 34 12.1 12.2 12.3 12.4 Related Links ........................................................ Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 34 34 34 34 13 Mechanical, Packaging, and Orderable Information ........................................................... 34 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision I (February 2013) to Revision J * Page Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1 Changes from Revision H (February 2013) to Revision I * 2 Page Changed layout of National Data Sheet to TI format ........................................................................................................... 32 Submit Documentation Feedback Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 www.ti.com SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 5 Description (Continued) The LMV321-N is available in the space saving 5-Pin SC70, which is approximately half the size of the 5-Pin SOT23. The small package saves space on PC boards and enables the design of small portable electronic devices. It also allows the designer to place the device closer to the signal source to reduce noise pickup and increase signal integrity. The chips are built with Texas Instruments's advanced submicron silicon-gate BiCMOS process. The LMV321N/LMV358-N/LMV324-N have bipolar input and output stages for improved noise performance and higher output current drive. 6 Pin Configuration and Functions DBV and DCK Package 5-Pin SC70, SOT-23 Top View D and DGK Package 8-Pin SOIC, VSSOP Top View D and PW Package 14-Pin SOIC, TSSOP Top View Pin Functions PIN NAME LMV321-N, LMV321-N-Q1, LMV321-N-Q3 DVB, DCK LMV358-N, LMV358-N-Q1, LMV358-N-Q3 D, DGK LMV324-N, LMV324-N-Q1, LMV324-N-Q3 D, PW TYPE DESCRIPTION +IN 1 - - I Noninverting input IN A+ - 3 3 I Noninverting input, channel A IN B+ - 5 5 I Noninverting input, channel B IN C+ - - 10 I Noninverting input, channel C IN D+ - - 12 I Noninverting input, channel D -IN 3 - - I Inverting input IN A- - 2 2 I Inverting input, channel A IN B- - 6 6 I Inverting input, channel B IN C- - - 9 I Inverting input, channel C IN D- - - 13 I Inverting input, channel D OUTPUT 4 - - O Output OUT A - 1 1 O Output, channel A OUT B - 7 7 O Output, channel B OUT C - - 8 O Output , channel C OUT D - - 14 O Output, channel D V+ 5 8 4 P Positive (highest) power supply V- 2 4 11 P Negative (lowest) power supply Copyright (c) 2000-2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 3 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 www.ti.com 7 Specifications 7.1 Absolute Maximum Ratings See (1) (2) . MIN Differential Input Voltage MAX UNIT Supply Voltage -0.3 Input Voltage V +Supply Voltage V 5.5 V Soldering Information: Infrared or Convection (30 sec) 260 C Junction Temperature (5) 150 C 150 C Supply Voltage (V+-V -) Output Short Circuit to V + (3) Output Short Circuit to V - (4) -65 Storage temperature Tstg (1) (2) (3) (4) (5) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Recommended Operating Conditions indicate conditions for which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test conditions, see the Electrical Characteristics. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office / Distributors for availability and specifications. Shorting output to V+ will adversely affect reliability. Shorting output to V- will adversely affect reliability. The maximum power dissipation is a function of TJ(MAX), RJA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) - TA)/ RJA. All numbers apply for packages soldered directly onto a PC Board. 7.2 ESD Ratings - Commercial VALUE UNIT LMV358-N, and LMV324-N in all packages V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) 2000 Machine model 100 Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) 900 Machine model 100 V LMV321-N in all packages V(ESD) (1) Electrostatic discharge V JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. 7.3 ESD Ratings - Automotive VALUE UNIT LMV358-N-Q1, LMV324-N-Q1, LMV358-N-Q3 and LMV324-N-Q3 in all packages V(ESD) Electrostatic discharge Human-body model (HBM), per AEC Q100-002 (1) 2000 Machine model 100 V LM321-N-Q1 and LM321-N-Q3 in all packages V(ESD) (1) Electrostatic discharge Human-body model (HBM), per AEC Q100-002 (1) 900 Machine model 100 V AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification. 7.4 Recommended Operating Conditions Supply Voltage (1) 4 MIN MAX 2.7 5.5 UNIT V Temperature Range (1) : LMV321-N, LMV358-N, LMV324-N -40 125 C Temperature Range (1) : LMV321-N-Q1, LMV358-N-Q1, LMV324-N-Q1 -40 125 C Temperature Range (1) -40 85 C : LMV321-N-Q3, LMV358-N-Q3, LMV324-N-Q3 The maximum power dissipation is a function of TJ(MAX), RJA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) - TA)/ RJA. All numbers apply for packages soldered directly onto a PC Board. Submit Documentation Feedback Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 www.ti.com SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 7.5 Thermal Information THERMAL METRIC (1) LMV321-N, LMV321-N-Q1, LMV321-N-Q3 LMV321-N DBV DCK LMV324-N, LMV324-N-Q1, LMV324-N-Q3 LMV358-N, LMV358-N-Q1, LMV358-N-Q3 D D 5 PINS RJA (1) Junction-to-ambient thermal resistance 265 PW 14 PINS 478 145 UNIT DGK 8 PINS 155 190 235 C/W For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953. 7.6 2.7-V DC Electrical Characteristics Unless otherwise specified, all limits specified for TJ = 25C, V+ = 2.7 V, V- = 0 V, VCM = 1.0 V, VO = V+/2 and RL > 1 M. TEST CONDITIONS MIN (1) TYP (2) MAX (1) 1.7 7 UNIT VOS Input Offset Voltage TCVOS Input Offset Voltage Average Drift IB Input Bias Current IOS Input Offset Current CMRR Common Mode Rejection Ratio 0 V VCM 1.7 V 50 63 dB PSRR Power Supply Rejection Ratio 2.7 V V+ 5 V VO = 1V 50 60 dB VCM Input Common-Mode Voltage Range For CMRR 50 dB 0 -0.2 V VO Output Swing RL = 10 k to 1.35 V V+ -100 V+ -10 IS (1) (2) Supply Current 5 V/C 11 250 nA 5 50 nA 1.9 Single mV 1.7 V mV 60 180 mV A 80 170 Dual Both amplifiers 140 340 Quad All four amplifiers 260 680 A A All limits are ensured by testing or statistical analysis. Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped production material. 7.7 2.7-V AC Electrical Characteristics Unless otherwise specified, all limits specified for T J = 25C, V+ = 2.7 V, V- = 0 V, VCM = 1.0 V, VO = V+/2 and RL > 1 M. TEST CONDITIONS TYP (2) MAX (1) UNIT GBWP Gain-Bandwidth Product 1 MHz m Phase Margin 60 Deg Gm Gain Margin 10 dB en Input-Referred Voltage Noise f = 1 kHz 46 in Input-Referred Current Noise f = 1 kHz 0.17 (1) (2) CL = 200 pF MIN (1) All limits are ensured by testing or statistical analysis. Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped production material. Copyright (c) 2000-2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 5 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 www.ti.com 7.8 5-V DC Electrical Characteristics Unless otherwise specified, all limits specified for T J = 25C, V+ = 5 V, V- = 0 V, VCM = 2.0 V, VO = V+/2 and R L > 1 M. MIN (1) TEST CONDITIONS VOS Input Offset Voltage TYP (2) MAX (1) 1.7 7 Over Temperature TCVOS Input Offset Voltage Average Drift IB Input Bias Current 9 5 15 Over Temperature IOS 5 Over Temperature mV V/C 250 500 Input Offset Current UNIT 50 150 nA nA CMRR Common Mode Rejection Ratio 0 V VCM 4 V 50 65 dB PSRR Power Supply Rejection Ratio 2.7 V V+ 5 V VO = 1V, VCM = 1 V 50 60 dB VCM Input Common-Mode Voltage Range For CMRR 50 dB 0 -0.2 V AV Large Signal Voltage Gain RL = 2 k 15 100 RL = 2 k, Over Temperature 10 VO (3) Output Swing 4.2 RL = 2 k to 2.5 V RL = 2 k to 2.5 V, Over Temperature V+ - 300 V - 400 120 V+ - 100 RL = 10 k to 2.5 V, Over Temperature V+ - 200 RL = 2 k to 2.5 V V+ - 10 65 RL = 2 k to 2.5 V, 125C Sinking, VO = 5 V IS Supply Current Single 60 10 160 130 (3) 6 mA 250 440 615 410 Quad (all four amps), Over Temperature (1) (2) 180 350 210 Dual (both amps), Over Temperature Quad (all four amps) mV 280 5 Single, Over Temperature Dual (both amps) 300 400 RL = 10 k to 2.5 V Sourcing, VO = 0 V V/mV V+ -40 RL = 2 k to 2.5 V, Over Temperature Output Short Circuit Current V + RL = 2 k to 2.5 V IO 4 A 830 1160 All limits are ensured by testing or statistical analysis. Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped production material. RL is connected to V-. The output voltage is 0.5 V VO 4.5 V. Submit Documentation Feedback Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 www.ti.com SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 7.9 5-V AC Electrical Characteristics Unless otherwise specified, all limits specified for TJ = 25C, V+ = 5 V, V- = 0 V, VCM = 2.0 V, VO = V+/2 and R L > 1 M. TEST CONDITIONS (3) MIN (1) TYP (2) SR Slew Rate GBWP Gain-Bandwidth Product m Gm en Input-Referred Voltage Noise f = 1 kHz 39 in Input-Referred Current Noise f = 1 kHz 0.21 (1) (2) (3) MAX (1) UNIT 1 V/s 1 MHz Phase Margin 60 Deg Gain Margin 10 dB CL = 200 pF All limits are ensured by testing or statistical analysis. Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped production material. Connected as voltage follower with 3-V step input. Number specified is the slower of the positive and negative slew rates. Copyright (c) 2000-2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 7 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 www.ti.com 7.10 Typical Characteristics Unless otherwise specified, VS = 5 V, single supply, TA = 25C. 8 Figure 1. Supply Current vs. Supply Voltage (LMV321-N) Figure 2. Input Current vs. Temperature Figure 3. Sourcing Current vs. Output Voltage Figure 4. Sourcing Current vs. Output Voltage Figure 5. Sinking Current vs. Output Voltage Figure 6. Sinking Current vs. Output Voltage Submit Documentation Feedback Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 www.ti.com SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 Typical Characteristics (continued) Unless otherwise specified, VS = 5 V, single supply, TA = 25C. Figure 7. Output Voltage Swing vs. Supply Voltage Figure 8. Input Voltage Noise vs. Frequency Figure 9. Input Current Noise vs. Frequency Figure 10. Input Current Noise vs. Frequency Figure 11. Crosstalk Rejection vs. Frequency Figure 12. PSRR vs. Frequency Copyright (c) 2000-2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 9 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 www.ti.com Typical Characteristics (continued) Unless otherwise specified, VS = 5 V, single supply, TA = 25C. 10 Figure 13. CMRR vs. Frequency Figure 14. CMRR vs. Input Common Mode Voltage Figure 15. CMRR vs. Input Common Mode Voltage Figure 16. VOS vs. CMR Figure 17. V OS vs. CMR Figure 18. Input Voltage vs. Output Voltage Submit Documentation Feedback Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 www.ti.com SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 Typical Characteristics (continued) Unless otherwise specified, VS = 5 V, single supply, TA = 25C. Figure 19. Input Voltage vs. Output Voltage Figure 20. Open Loop Frequency Response Figure 21. Open Loop Frequency Response Figure 22. Open Loop Frequency Response vs. Temperature Figure 23. Gain and Phase vs. Capacitive Load Figure 24. Gain and Phase vs. Capacitive Load Copyright (c) 2000-2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 11 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 www.ti.com Typical Characteristics (continued) Unless otherwise specified, VS = 5 V, single supply, TA = 25C. 12 Figure 25. Slew Rate vs. Supply Voltage Figure 26. Non-Inverting Large Signal Pulse Response Figure 27. Non-Inverting Large Signal Pulse Response Figure 28. Non-Inverting Large Signal Pulse Response Figure 29. Non-Inverting Small Signal Pulse Response Figure 30. Non-Inverting Small Signal Pulse Response Submit Documentation Feedback Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 www.ti.com SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 Typical Characteristics (continued) Unless otherwise specified, VS = 5 V, single supply, TA = 25C. Figure 31. Non-Inverting Small Signal Pulse Response Figure 32. Inverting Large Signal Pulse Response Figure 33. Inverting Large Signal Pulse Response Figure 34. Inverting Large Signal Pulse Response Figure 35. Inverting Small Signal Pulse Response Figure 36. Inverting Small Signal Pulse Response Copyright (c) 2000-2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 13 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 www.ti.com Typical Characteristics (continued) Unless otherwise specified, VS = 5 V, single supply, TA = 25C. Figure 37. Inverting Small Signal Pulse Response Figure 38. Stability vs. Capacitive Load 14 Figure 39. Stability vs. Capacitive Load Figure 40. Stability vs. Capacitive Load Figure 41. Stability vs. Capacitive Load Figure 42. THD vs. Frequency Submit Documentation Feedback Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 www.ti.com SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 Typical Characteristics (continued) Unless otherwise specified, VS = 5 V, single supply, TA = 25C. Figure 43. Open Loop Output Impedance vs. Frequency Figure 44. Short Circuit Current vs. Temperature (Sinking) Figure 45. Short Circuit Current vs. Temperature (Sourcing) Copyright (c) 2000-2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 15 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 www.ti.com 8 Detailed Description 8.1 Overview The LMV358-N/LMV324-N are low voltage (2.7 V to 5.5 V) versions of the dual and quad commodity op amps LM358/LM324 (5 V to 30 V). The LMV321-N is the single channel version. The LMV321-N/LMV358-N/LMV324-N are the most cost effective solutions for applications where low voltage operation, space efficiency, and low price are important. They offer specifications that meet or exceed the familiar LM358/LM324. The LMV321-N/LMV358N/LMV324-N have rail-to-rail output swing capability and the input common-mode voltage range includes ground. They all exhibit excellent speed to power ratio, achieving 1 MHz of bandwidth and 1-V/s slew rate with low supply current. 8.1.1 Benefits of the LMV321-N/LMV358-N/LMV324-N 8.1.1.1 Size The small footprints of the LMV321-N/LMV358-N/LMV324-N packages save space on printed circuit boards, and enable the design of smaller electronic products, such as cellular phones, pagers, or other portable systems. The low profile of the LMV321-N/LMV358-N/LMV324-N make them possible to use in PCMCIA type III cards. 8.1.1.2 Signal Integrity Signals can pick up noise between the signal source and the amplifier. By using a physically smaller amplifier package, the LMV321-N/LMV358-N/LMV324-N can be placed closer to the signal source, reducing noise pickup and increasing signal integrity. 8.1.1.3 Simplified Board Layout These products help you to avoid using long PC traces in your PC board layout. This means that no additional components, such as capacitors and resistors, are needed to filter out the unwanted signals due to the interference between the long PC traces. 8.1.1.4 Low Supply Current These devices will help you to maximize battery life. They are ideal for battery powered systems. 8.1.1.5 Low Supply Voltage Texas Instruments provides ensured performance at 2.7 V and 5 V. These specifications ensure operation throughout the battery lifetime. 8.1.1.6 Rail-to-Rail Output Rail-to-rail output swing provides maximum possible dynamic range at the output. This is particularly important when operating on low supply voltages. 8.1.1.7 Input Includes Ground Allows direct sensing near GND in single supply operation. Protection should be provided to prevent the input voltages from going negative more than -0.3V (at 25C). An input clamp diode with a resistor to the IC input terminal can be used. 8.1.1.8 Ease of Use and Crossover Distortion The LMV321-N/LMV358-N/LMV324-N offer specifications similar to the familiar LM324-N. In addition, the new LMV321-N/LMV358-N/LMV324-N effectively eliminate the output crossover distortion. The scope photos in Figure 46 and Figure 47 compare the output swing of the LMV324-N and the LM324-N in a voltage follower configuration, with VS = 2.5V and RL (= 2 k) connected to GND. It is apparent that the crossover distortion has been eliminated in the new LMV324-N. 16 Submit Documentation Feedback Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 www.ti.com SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 Overview (continued) Figure 46. Output Swing of LMV324 Figure 47. Output Swing of LM324 8.2 Functional Block Diagram V IN - IN + + _ OUT + V - Copyright (c) 2016, Texas Instruments Incorporated Figure 48. Each Amplifier 8.3 Feature Description 8.3.1 Capacitive Load Tolerance The LMV321-N/LMV358-N/LMV324-N can directly drive 200 pF in unity-gain without oscillation. The unity-gain follower is the most sensitive configuration to capacitive loading. Direct capacitive loading reduces the phase margin of amplifiers. The combination of the amplifier's output impedance and the capacitive load induces phase lag. This results in either an underdamped pulse response or oscillation. To drive a heavier capacitive load, the circuit in Figure 49 can be used. Figure 49. Indirectly Driving a Capacitive Load Using Resistive Isolation In Figure 49 , the isolation resistor RISO and the load capacitor CL form a pole to increase stability by adding more phase margin to the overall system. The desired performance depends on the value of RISO. The bigger the RISO resistor value, the more stable VOUT will be. Figure 50 is an output waveform of Figure 49 using 620 for RISO and 510 pF for CL.. Copyright (c) 2000-2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 17 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 www.ti.com Feature Description (continued) Figure 50. Pulse Response of the LMV324 Circuit in Figure 49 The circuit in Figure 51 is an improvement to the one in Figure 49 because it provides DC accuracy as well as AC stability. If there were a load resistor in Figure 49, the output would be voltage divided by RISO and the load resistor. Instead, in Figure 51, RF provides the DC accuracy by using feed-forward techniques to connect VIN to RL. Caution is needed in choosing the value of RF due to the input bias current of theLMV321-N/LMV358N/LMV324-N. CF and RISO serve to counteract the loss of phase margin by feeding the high frequency component of the output signal back to the amplifier's inverting input, thereby preserving phase margin in the overall feedback loop. Increased capacitive drive is possible by increasing the value of CF . This in turn will slow down the pulse response. Figure 51. Indirectly Driving A Capacitive Load with DC Accuracy 8.3.2 Input Bias Current Cancellation The LMV321-N/LMV358-N/LMV324-N family has a bipolar input stage. The typical input bias current of LMV321N/LMV358-N/LMV324-N is 15 nA with 5V supply. Thus a 100 k input resistor will cause 1.5 mV of error voltage. By balancing the resistor values at both inverting and non-inverting inputs, the error caused by the amplifier's input bias current will be reduced. The circuit in Figure 52 shows how to cancel the error caused by input bias current. 18 Submit Documentation Feedback Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 www.ti.com SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 Feature Description (continued) Figure 52. Cancelling the Error Caused by Input Bias Current 8.4 Device Functional Modes The LMV321-N/LMV321-N-Q1/LMV358-N/LMV358-N-Q1/LMV324-N/LMV324-N-Q1 are powered on when the supply is connected. They can be operated as a single supply or a dual supply operational amplifier depending on the application. Copyright (c) 2000-2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 19 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 www.ti.com 9 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI's customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 9.1 Application Information The LMV32x-N family of amplifiers is specified for operation from 2.7 V to 5 V (1.35 V to 2.5 V). Many of the specifications apply from -40C to 125C. They provide ground-sensing inputs as well as rail-to-rail output swing. Parameters that can exhibit significant variance with regard to operating voltage or temperature are presented in the Typical Characteristics. 9.2 Typical Applications 9.2.1 Simple Low-Pass Active Filter A simple active low-pass filter is shown in Figure 53. Figure 53. Simple Low-Pass Active Filter 9.2.1.1 Design Requirements The simple single pole active lowpass filter shown in Figure 53 will pass low frequencies and attenuate frequencies above corner frequency (fc) at a roll-off rate of 20dB/Decade. 9.2.1.2 Detailed Design Procedure The values of R1, R2, R3 and C1 are selected using the formulas in Figure 54. The low-frequency gain ( 0) is defined by -R3/R1. This allows low-frequency gains other than unity to be obtained. The filter has a -20 dB/decade roll-off after its corner frequency fc. R2 should be chosen equal to the parallel combination of R1 and R3 to minimize errors due to bias current. The frequency response of the filter is shown in Figure 55. Figure 54. Simple Low-Pass Active Filter Equations 20 Submit Documentation Feedback Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 www.ti.com SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 Typical Applications (continued) 9.2.1.3 Application Curves Figure 55. Frequency Response of Simple Low-Pass Active Filter Note that the single-op-amp active filters are used in the applications that require low quality factor, Q( 10), low frequency ( 5 kHz), and low gain ( 10), or a small value for the product of gain times Q ( 100). The op amp should have an open loop voltage gain at the highest frequency of interest at least 50 times larger than the gain of the filter at this frequency. In addition, the selected op amp should have a slew rate that meets the following requirement: Slew Rate 0.5 x ( HVOPP) x 10-6 V/sec (1) where H is the highest frequency of interest, and VOPP is the output peak-to-peak voltage. 9.2.2 Difference Amplifier The difference amplifier allows the subtraction of two voltages or, as a special case, the cancellation of a signal common to two inputs. It is useful as a computational amplifier, in making a differential to single-ended conversion or in rejecting a common mode signal. Figure 56. Difference Amplifier 9.2.3 Instrumentation Circuits The input impedance of the previous difference amplifier is set by the resistors R1, R2, R3, and R4. To eliminate the problems of low input impedance, one way is to use a voltage follower ahead of each input as shown in the following two instrumentation amplifiers. Copyright (c) 2000-2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 21 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 www.ti.com Typical Applications (continued) 9.2.3.1 Three-Op-Amp Instrumentation Amplifier The quad LMV324 can be used to build a three-op-amp instrumentation amplifier as shown in Figure 57. Figure 57. Three-Op-Amp Instrumentation Amplifier The first stage of this instrumentation amplifier is a differential-input, differential-output amplifier, with two voltage followers. These two voltage followers assure that the input impedance is over 100 M. The gain of this instrumentation amplifier is set by the ratio of R2/R1. R3 should equal R1, and R4 equal R2. Matching of R3 to R1 and R4 to R2 affects the CMRR. For good CMRR over temperature, low drift resistors should be used. Making R4 slightly smaller than R2 and adding a trim pot equal to twice the difference between R2 and R4 will allow the CMRR to be adjusted for optimum performance. 9.2.3.2 Two-Op-Amp Instrumentation Amplifier A two-op-amp instrumentation amplifier can also be used to make a high-input-impedance DC differential amplifier (Figure 58). As in the three-op-amp circuit, this instrumentation amplifier requires precise resistor matching for good CMRR. R4 should equal R1 and, R3 should equal R2. Figure 58. Two-Op-Amp Instrumentation Amplifier 22 Submit Documentation Feedback Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 www.ti.com SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 Typical Applications (continued) 9.2.3.3 Single-Supply Inverting Amplifier There may be cases where the input signal going into the amplifier is negative. Because the amplifier is operating in single supply voltage, a voltage divider using R3 and R4 is implemented to bias the amplifier so the input signal is within the input common-mode voltage range of the amplifier. The capacitor C1 is placed between the inverting input and resistor R1 to block the DC signal going into the AC signal source, VIN. The values of R1 and C1 affect the cutoff frequency, fc = 1/2R1C1. As a result, the output signal is centered around mid-supply (if the voltage divider provides V+/2 at the noninverting input). The output can swing to both rails, maximizing the signal-to-noise ratio in a low voltage system. Figure 59. Single-Supply Inverting Amplifier 9.2.4 Sallen-Key 2nd-Order Active Low-Pass Filter The Sallen-Key 2nd-order active low-pass filter is illustrated in Figure 60. The DC gain of the filter is expressed as (2) Its transfer function is (3) Figure 60. Sallen-Key 2nd-Order Active Low-Pass Filter Copyright (c) 2000-2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 23 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 www.ti.com Typical Applications (continued) 9.2.4.1 Detailed Design Procedure The following paragraphs explain how to select values for R1, R2, R3, R4, C1, and C 2 for given filter requirements, such as ALP, Q, and fc. The standard form for a 2nd-order low pass filter is (4) where Q: Pole Quality Factor C: Corner Frequency A comparison between Equation 3 and Equation 4 yields (5) (6) To reduce the required calculations in filter design, it is convenient to introduce normalization into the components and design parameters. To normalize, let C = n = 1 rad/s, and C1 = C2 = Cn = 1F, and substitute these values into Equation 5 and Equation 6. From Equation 5, we obtain (7) From Equation 6, we obtain (8) + - For minimum DC offset, V = V , the resistor values at both inverting and non-inverting inputs should be equal, which means (9) From Equation 2 and Equation 9, we obtain (10) (11) The values of C1 and C2 are normally close to or equal to (12) As a design example: Require: ALP = 2, Q = 1, fc = 1 kHz Start by selecting C1 and C2. Choose a standard value that is close to (13) (14) 24 Submit Documentation Feedback Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 www.ti.com SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 Typical Applications (continued) From Equation 7, Equation 8, Equation 10, and Equation 11, R1= R2= R3= R4= 1 1 4 4 (15) (16) (17) (18) The above resistor values are normalized values with n = 1 rad/s and C1 = C2 = Cn = 1F. To scale the normalized cutoff frequency and resistances to the real values, two scaling factors are introduced, frequency scaling factor (kf) and impedance scaling factor (km). (19) Scaled values: R2 = R1 = 15.9 k R3 = R4 = 63.6 k C1 = C2 = 0.01 F (20) (21) (22) An adjustment to the scaling may be made in order to have realistic values for resistors and capacitors. The actual value used for each component is shown in the circuit. 9.2.5 2nd-Order High Pass Filter A 2nd-order high pass filter can be built by simply interchanging those frequency selective components (R1, R2, C1, C2) in the Sallen-Key 2nd-order active low pass filter. As shown in Figure 61, resistors become capacitors, and capacitors become resistors. The resulted high pass filter has the same corner frequency and the same maximum gain as the previous 2nd-order low pass filter if the same components are chosen. Figure 61. Sallen-Key 2nd-Order Active High-Pass Filter 9.2.6 State Variable Filter A state variable filter requires three op amps. One convenient way to build state variable filters is with a quad op amp, such as the LMV324 (Figure 62). Copyright (c) 2000-2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 25 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 www.ti.com Typical Applications (continued) This circuit can simultaneously represent a low-pass filter, high-pass filter, and bandpass filter at three different outputs. The equations for these functions are listed below. It is also called "Bi-Quad" active filter as it can produce a transfer function which is quadratic in both numerator and denominator. Figure 62. State Variable Active Filter (23) where for all three filters, (24) (25) 9.2.6.1 Detailed Design Procedure Assume the system design requires a bandpass filter with f are capacitor and resistor values. O = 1 kHz and Q = 50. What needs to be calculated First choose convenient values for C1, R1 and R2: C1 = 1200 pF 26 Submit Documentation Feedback (26) Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 www.ti.com SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 Typical Applications (continued) 2R2 = R1 = 30 k (27) Then from Equation 24, (28) From Equation 25, (29) From the above calculated values, the midband gain is H0 = R3/R2 = 100 (40 dB). The nearest 5% standard values have been added to Figure 62. 9.2.7 Pulse Generators and Oscillators A pulse generator is shown in Figure 63. Two diodes have been used to separate the charge and discharge paths to capacitor C. Figure 63. Pulse Generator When the output voltage VO is first at its high, VOH, the capacitor C is charged toward VOH through R2. The voltage across C rises exponentially with a time constant = R2C, and this voltage is applied to the inverting input of the op amp. Meanwhile, the voltage at the non-inverting input is set at the positive threshold voltage (VTH+) of the generator. The capacitor voltage continually increases until it reaches VTH+, at which point the output of the generator will switch to its low, VOL which 0V is in this case. The voltage at the non-inverting input is switched to the negative threshold voltage (VTH-) of the generator. The capacitor then starts to discharge toward VOL exponentially through R1, with a time constant = R1C. When the capacitor voltage reaches VTH-, the output of the pulse generator switches to VOH. The capacitor starts to charge, and the cycle repeats itself. Copyright (c) 2000-2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 27 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 www.ti.com Typical Applications (continued) Figure 64. Waveforms of the Circuit in Figure 16 As shown in the waveforms in Figure 64, the pulse width (T1) is set by R2, C and VOH, and the time between pulses (T2) is set by R1, C and VOL. This pulse generator can be made to have different frequencies and pulse width by selecting different capacitor value and resistor values. Figure 65 shows another pulse generator, with separate charge and discharge paths. The capacitor is charged through R1 and is discharged through R2. 28 Submit Documentation Feedback Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 www.ti.com SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 Typical Applications (continued) Figure 65. Pulse Generator Figure 66 is a squarewave generator with the same path for charging and discharging the capacitor. Figure 66. Squarewave Generator 9.2.8 Current Source and Sink The LMV321-N/LMV358-N/LMV324-N can be used in feedback loops which regulate the current in external PNP transistors to provide current sources or in external NPN transistors to provide current sinks. 9.2.8.1 Fixed Current Source A multiple fixed current source is shown in Figure 67. A voltage (VREF = 2V) is established across resistor R3 by the voltage divider (R3 and R4). Negative feedback is used to cause the voltage drop across R1 to be equal to VREF. This controls the emitter current of transistor Q1 and if we neglect the base current of Q1 and Q2, essentially this same current is available out of the collector of Q1. Large input resistors can be used to reduce current loss and a Darlington connection can be used to reduce errors due to the of Q1. The resistor, R2, can be used to scale the collector current of Q2 either above or below the 1 mA reference value. Copyright (c) 2000-2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 29 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 www.ti.com Typical Applications (continued) Figure 67. Fixed Current Source 9.2.8.2 High Compliance Current Sink A current sink circuit is shown in Figure 68. The circuit requires only one resistor (RE) and supplies an output current which is directly proportional to this resistor value. Figure 68. High Compliance Current Sink 30 Submit Documentation Feedback Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 www.ti.com SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 Typical Applications (continued) 9.2.9 Power Amplifier A power amplifier is illustrated in Figure 69. This circuit can provide a higher output current because a transistor follower is added to the output of the op amp. Figure 69. Power Amplifier 9.2.10 LED Driver The LMV321-N/LMV358-N/LMV324-N can be used to drive an LED as shown in Figure 70. Figure 70. LED Driver 9.2.11 Comparator With Hysteresis The LMV321-N/LMV358-N/LMV324-N can be used as a low power comparator. Figure 71 shows a comparator with hysteresis. The hysteresis is determined by the ratio of the two resistors. VTH+ = VREF/(1+R 1/R2)+VOH/(1+R2/R1) VTH- = VREF/(1+R 1/R2)+VOL/(1+R2/R1) VH = (VOH-VOL)/(1+R 2/R1) (30) (31) (32) where VTH+: Positive Threshold Voltage VTH-: Negative Threshold Voltage VOH: Output Voltage at High VOL: Output Voltage at Low VH: Hysteresis Voltage Since LMV321-N/LMV358-N/LMV324-N have rail-to-rail output, the (VOH-VOL) is equal to VS, which is the supply voltage. VH = VS/(1+R2/R1) Copyright (c) 2000-2014, Texas Instruments Incorporated (33) Submit Documentation Feedback Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 31 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 www.ti.com Typical Applications (continued) The differential voltage at the input of the op amp should not exceed the specified absolute maximum ratings. For real comparators that are much faster, we recommend you use Texas Instruments's LMV331/LMV93/LMV339, which are single, dual and quad general purpose comparators for low voltage operation. Figure 71. Comparator with Hysteresis 10 Power Supply Recommendations The LMV3xx-N is specified for operation from 2.7 V to 5.5 V; many specifications apply from -40C to 125C. Parameters that can exhibit significant variance with regard to operating voltage or temperature are presented in the Typical Characteristics. Place 0.1-F bypass capacitors close to the power-supply pins to reduce errors coupling in from noisy or high impedance power supplies. For more detailed information on bypass capacitor placement, refer to the Layout Guidelines section. 11 Layout 11.1 Layout Guidelines For best operational performance of the device, use good PCB layout practices, including: * Noise can propagate into analog circuitry through the power pins of the circuit as a whole and the operational amplifier. Bypass capacitors are used to reduce the coupled noise by providing low impedance power sources local to the analog circuitry. - Connect low-ESR, 0.1-F ceramic bypass capacitors between each supply pin and ground, placed as close to the device as possible. A single bypass capacitor from V+ to ground is applicable for single supply applications. * Separate grounding for analog and digital portions of circuitry is one of the simplest and most-effective methods of noise suppression. One or more layers on multilayer PCBs are usually devoted to ground planes. A ground plane helps distribute heat and reduces EMI noise pickup. Make sure to physically separate digital and analog grounds, paying attention to the flow of the ground current. For more detailed information, refer to Circuit Board Layout Techniques, SLOA089. * To reduce parasitic coupling, run the input traces as far away from the supply or output traces as possible. If it is not possible to keep them separate, it is much better to cross the sensitive trace perpendicular as opposed to in parallel with the noisy trace. * Place the external components as close to the device as possible. Keeping RF and RG close to the inverting input minimizes parasitic capacitance, as shown in Layout Example. * Keep the length of input traces as short as possible. Always remember that the input traces are the most sensitive part of the circuit. * Consider a driven, low-impedance guard ring around the critical traces. A guard ring can significantly reduce leakage currents from nearby traces that are at different potentials. 32 Submit Documentation Feedback Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 www.ti.com SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 11.2 Layout Example Figure 72. Operational Amplifier Board Layout for Noninverting Configuration Copyright (c) 2000-2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 33 LMV321-N, LMV321-N-Q1, LMV358-N LMV358-N-Q1, LMV324-N, LMV324-N-Q1 SNOS012J - AUGUST 2000 - REVISED DECEMBER 2014 www.ti.com 12 Device and Documentation Support 12.1 Related Links The table below lists quick access links. Categories include technical documents, support and community resources, tools and software, and quick access to sample or buy. Table 1. Related Links PARTS PRODUCT FOLDER SAMPLE & BUY TECHNICAL DOCUMENTS TOOLS & SOFTWARE SUPPORT & COMMUNITY LMV321-N Click here Click here Click here Click here Click here LMV321-N-Q1 Click here Click here Click here Click here Click here LMV358-N Click here Click here Click here Click here Click here LMV358-N-Q1 Click here Click here Click here Click here Click here LMV324-N Click here Click here Click here Click here Click here LMV324-N-Q1 Click here Click here Click here Click here Click here 12.2 Trademarks All trademarks are the property of their respective owners. 12.3 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 12.4 Glossary SLYZ022 -- TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 13 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. 34 Submit Documentation Feedback Copyright (c) 2000-2014, Texas Instruments Incorporated Product Folder Links: LMV321-N LMV321-N-Q1 LMV358-N LMV358-N-Q1 LMV324-N LMV324-N-Q1 PACKAGE OPTION ADDENDUM www.ti.com 19-Dec-2017 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LMV321M5 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 A13 LMV321M5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 A13 LMV321M5X/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 A13 LMV321M7 NRND SC70 DCK 5 1000 TBD Call TI Call TI -40 to 125 A12 LMV321M7/NOPB ACTIVE SC70 DCK 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 A12 LMV321M7X NRND SC70 DCK 5 3000 TBD Call TI Call TI -40 to 125 A12 LMV321M7X/NOPB ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 A12 LMV321Q1M5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 AYA LMV321Q1M5X/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 AYA LMV321Q3M5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 AZA LMV321Q3M5X/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 AZA LMV324M NRND SOIC D 14 55 TBD Call TI Call TI -40 to 125 LMV324M LMV324M/NOPB ACTIVE SOIC D 14 55 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LMV324M LMV324MT/NOPB ACTIVE TSSOP PW 14 94 Green (RoHS & no Sb/Br) CU NIPDAU | CU SN Level-1-260C-UNLIM -40 to 125 LMV324 MT LMV324MTX NRND TSSOP PW 14 2500 TBD Call TI Call TI -40 to 125 LMV324 MT LMV324MTX/NOPB ACTIVE TSSOP PW 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU | CU SN Level-1-260C-UNLIM -40 to 125 LMV324 MT LMV324MX NRND SOIC D 14 2500 TBD Call TI Call TI -40 to 125 LMV324M LMV324MX/NOPB ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LMV324M LMV324Q1MA/NOPB ACTIVE SOIC D 14 55 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LMV324Q1 MA Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 19-Dec-2017 Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LMV324Q1MAX/NOPB ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LMV324Q1 MA LMV324Q1MT/NOPB ACTIVE TSSOP PW 14 94 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LMV324 Q1MT LMV324Q1MTX/NOPB ACTIVE TSSOP PW 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LMV324 Q1MT LMV324Q3MA/NOPB ACTIVE SOIC D 14 55 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LMV324Q3 MA LMV324Q3MAX/NOPB ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LMV324Q3 MA LMV324Q3MT/NOPB ACTIVE TSSOP PW 14 94 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LMV324 Q3MT LMV324Q3MTX/NOPB ACTIVE TSSOP PW 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LMV324 Q3MT LMV358M NRND SOIC D 8 95 TBD Call TI Call TI -40 to 125 LMV 358M LMV358M/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LMV 358M LMV358MM NRND VSSOP DGK 8 1000 TBD Call TI Call TI -40 to 125 V358 LMV358MM/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 V358 LMV358MMX/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 V358 LMV358MX NRND SOIC D 8 2500 TBD Call TI Call TI -40 to 125 LMV 358M LMV358MX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LMV 358M LMV358Q1MA/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LMV35 8Q1MA LMV358Q1MAX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LMV35 8Q1MA LMV358Q1MM/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 AFAA LMV358Q1MMX/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 AFAA Addendum-Page 2 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 19-Dec-2017 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LMV358Q3MA/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LMV35 8Q3MA LMV358Q3MAX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LMV35 8Q3MA LMV358Q3MM/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 AHAA LMV358Q3MMX/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 AHAA (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. Addendum-Page 3 Samples PACKAGE OPTION ADDENDUM www.ti.com 19-Dec-2017 In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF LMV321-N, LMV321-N-Q1, LMV324-N, LMV324-N-Q1, LMV358-N, LMV358-N-Q1 : * Catalog: LMV321-N, LMV324-N, LMV358-N * Automotive: LMV321-N-Q1, LMV324-N-Q1, LMV358-N-Q1 NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 4 PACKAGE MATERIALS INFORMATION www.ti.com 23-Jun-2018 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) LMV321M5 SOT-23 DBV 5 1000 178.0 8.4 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 3.2 3.2 1.4 4.0 8.0 Q3 LMV321M5/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LMV321M5X/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LMV321M7 SC70 DCK 5 1000 178.0 8.4 2.25 2.45 1.2 4.0 8.0 Q3 LMV321M7/NOPB SC70 DCK 5 1000 178.0 8.4 2.25 2.45 1.2 4.0 8.0 Q3 LMV321M7X SC70 DCK 5 3000 178.0 8.4 2.25 2.45 1.2 4.0 8.0 Q3 LMV321M7X/NOPB SC70 DCK 5 3000 178.0 8.4 2.25 2.45 1.2 4.0 8.0 Q3 LMV321Q1M5/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LMV321Q1M5X/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LMV321Q3M5/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LMV321Q3M5X/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LMV324MTX TSSOP PW 14 2500 330.0 12.4 6.95 5.6 1.6 8.0 12.0 Q1 LMV324MTX/NOPB TSSOP PW 14 2500 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 LMV324MX SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1 LMV324MX/NOPB SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1 LMV324Q1MAX/NOPB SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1 LMV324Q1MTX/NOPB TSSOP PW 14 2500 330.0 12.4 6.95 5.6 1.6 8.0 12.0 Q1 LMV324Q3MAX/NOPB SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 23-Jun-2018 Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LMV324Q3MTX/NOPB TSSOP PW 14 2500 330.0 12.4 6.95 5.6 1.6 8.0 12.0 Q1 LMV358MM VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LMV358MM/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LMV358MMX/NOPB VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LMV358MX SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LMV358MX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LMV358Q1MAX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LMV358Q1MM/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LMV358Q1MMX/NOPB VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LMV358Q3MAX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LMV358Q3MM/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LMV358Q3MMX/NOPB VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LMV321M5 SOT-23 DBV 5 1000 210.0 185.0 35.0 LMV321M5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LMV321M5X/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LMV321M7 SC70 DCK 5 1000 210.0 185.0 35.0 LMV321M7/NOPB SC70 DCK 5 1000 210.0 185.0 35.0 Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 23-Jun-2018 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LMV321M7X SC70 DCK 5 3000 210.0 185.0 35.0 LMV321M7X/NOPB SC70 DCK 5 3000 210.0 185.0 35.0 LMV321Q1M5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LMV321Q1M5X/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LMV321Q3M5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LMV321Q3M5X/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LMV324MTX TSSOP PW 14 2500 367.0 367.0 35.0 LMV324MTX/NOPB TSSOP PW 14 2500 367.0 367.0 35.0 LMV324MX SOIC D 14 2500 367.0 367.0 35.0 LMV324MX/NOPB SOIC D 14 2500 367.0 367.0 35.0 LMV324Q1MAX/NOPB SOIC D 14 2500 367.0 367.0 35.0 LMV324Q1MTX/NOPB TSSOP PW 14 2500 367.0 367.0 35.0 LMV324Q3MAX/NOPB SOIC D 14 2500 367.0 367.0 35.0 LMV324Q3MTX/NOPB TSSOP PW 14 2500 367.0 367.0 35.0 LMV358MM VSSOP DGK 8 1000 210.0 185.0 35.0 LMV358MM/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0 LMV358MMX/NOPB VSSOP DGK 8 3500 367.0 367.0 35.0 LMV358MX SOIC D 8 2500 367.0 367.0 35.0 LMV358MX/NOPB SOIC D 8 2500 367.0 367.0 35.0 LMV358Q1MAX/NOPB SOIC D 8 2500 367.0 367.0 35.0 LMV358Q1MM/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0 LMV358Q1MMX/NOPB VSSOP DGK 8 3500 367.0 367.0 35.0 LMV358Q3MAX/NOPB SOIC D 8 2500 367.0 367.0 35.0 LMV358Q3MM/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0 LMV358Q3MMX/NOPB VSSOP DGK 8 3500 367.0 367.0 35.0 Pack Materials-Page 3 PACKAGE OUTLINE DBV0005A SOT-23 - 1.45 mm max height SCALE 4.000 SMALL OUTLINE TRANSISTOR C 3.0 2.6 1.75 1.45 PIN 1 INDEX AREA 1 0.1 C B A 5 2X 0.95 1.9 1.45 MAX 3.05 2.75 1.9 2 4 0.5 5X 0.3 0.2 3 (1.1) C A B 0.15 TYP 0.00 0.25 GAGE PLANE 8 TYP 0 0.22 TYP 0.08 0.6 TYP 0.3 SEATING PLANE 4214839/C 04/2017 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Refernce JEDEC MO-178. www.ti.com EXAMPLE BOARD LAYOUT DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X (0.95) 3 4 (R0.05) TYP (2.6) LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:15X SOLDER MASK OPENING METAL SOLDER MASK OPENING METAL UNDER SOLDER MASK EXPOSED METAL EXPOSED METAL 0.07 MIN ARROUND 0.07 MAX ARROUND NON SOLDER MASK DEFINED (PREFERRED) SOLDER MASK DEFINED SOLDER MASK DETAILS 4214839/C 04/2017 NOTES: (continued) 4. Publication IPC-7351 may have alternate designs. 5. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com EXAMPLE STENCIL DESIGN DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X(0.95) 4 3 (R0.05) TYP (2.6) SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE:15X 4214839/C 04/2017 NOTES: (continued) 6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 7. Board assembly site may have different recommendations for stencil design. www.ti.com PACKAGE OUTLINE DBV0005A SOT-23 - 1.45 mm max height SCALE 4.000 SMALL OUTLINE TRANSISTOR C 3.0 2.6 1.75 1.45 PIN 1 INDEX AREA 1 0.1 C B A 5 2X 0.95 1.9 1.45 MAX 3.05 2.75 1.9 2 4 0.5 5X 0.3 0.2 3 (1.1) C A B 0.15 TYP 0.00 0.25 GAGE PLANE 8 TYP 0 0.22 TYP 0.08 0.6 TYP 0.3 SEATING PLANE 4214839/C 04/2017 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Refernce JEDEC MO-178. www.ti.com EXAMPLE BOARD LAYOUT DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X (0.95) 3 4 (R0.05) TYP (2.6) LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:15X SOLDER MASK OPENING METAL SOLDER MASK OPENING METAL UNDER SOLDER MASK EXPOSED METAL EXPOSED METAL 0.07 MIN ARROUND 0.07 MAX ARROUND NON SOLDER MASK DEFINED (PREFERRED) SOLDER MASK DEFINED SOLDER MASK DETAILS 4214839/C 04/2017 NOTES: (continued) 4. Publication IPC-7351 may have alternate designs. 5. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com EXAMPLE STENCIL DESIGN DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X(0.95) 4 3 (R0.05) TYP (2.6) SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE:15X 4214839/C 04/2017 NOTES: (continued) 6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 7. Board assembly site may have different recommendations for stencil design. www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2018, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LMV324M LMV324M/NOPB LMV324MT/NOPB LMV324MTX LMV324MTX/NOPB LMV324MX LMV324MX/NOPB