/u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32660 Metallized Polypropylene Film Capacitors (MKP) Uncoated (Silver Caps) MKP stacked-film capacitors Extremely small dimensions Outstanding contact reliability B 32 660 Cut surfaces Construction Dielectric: polypropylene Stacked-film technology Uncoated Features Special dimensions available upon request High pulse strength High ac-loads Small dimensions Dimensions in mm Lead spacing 0,4 7,5 Diameter d1 Type 0,5 B 32 660 Typical applications Lamp ballast circuits Snubbering of semi-conductors Terminals Parallel wire leads, tinned (for CR = 2,2 ... 6,8 nF) Crimped leads, tinned (for CR 1,5 nF) Marking Rated capacitance (coded), rated dc voltage Delivery mode Bulk (untaped) Taped (Ammo pack or reel) For notes on taping, refer to page 279. Notes on mounting When mounting these capacitors, take into account creepage distances and clearances to adjacent live parts. The insulating strength of the cut surfaces to other live parts of the circuit is 1,5 times the capacitors rated dc voltage, but is always at least 300 Vdc. Capacitors with 7,5 mm lead spacing are only suitable for use with single-clad printed circuit boards. Siemens Matsushita Components 131 B 32 660 MKP 7,5 Ordering codes and packing units VR (Vrms , f 1 kHz) CR Maximum dimensions b x h x l (mm) Ordering code1) 1000 Vdc (450 Vac) 0,15 nF2) 0,22 nF 0,33 nF 0,47 nF 0,68 nF 1,0 nF 1,5 nF 2,2 nF 3,3 nF 4,7 nF 5,6 nF 6,8 nF 3,1 x 6,9 x 9,0 3,9 x 7,3 x 9,0 4,4 x 9,1 x 9,0 3,2 x 6,5 x 9,0 4,0 x 7,2 x 9,0 4,9 x 8,1 x 9,0 5,5 x 10,3 x 9,0 5,4 x 7,6 x 9,0 5,4 x 10,0 x 9,0 5,4 x 14,8 x 9,0 8,2 x 10,9 x 9,0 9,2 x 11,2 x 9,0 B32660-A8151-K*** B32660-A8221-+*** B32660-A8331-+*** B32660-A8471-+*** B32660-A8681-+*** B32660-A8102-+*** B32660-A8152-+*** B32660-A8222-+*** B32660-A8332-+*** B32660-A8472-+*** B32660-A8562-+*** B32660-A8682-+*** 1000 Vdc (600 Vac) Packing units (pcs) Ammo Reel Untaped pack 2800 2200 1200 2200 1700 900 2000 1600 600 2700 2200 1250 2100 1700 850 1800 1400 600 1600 1300 400 1700 1300 600 1600 1300 400 1600 1300 300 - - 200 - - 200 Capacitance tolerance: 10 % = K ( 5 % = J upon request) Capacitors with CR 1,5 nF are only available with crimped leads. Crimping increases the mounting height by approx. 4 mm (also refer to "Taping and Packing", page 279). 1) Replace the + by the code letter for the required capacitance tolerance. Replace the *** by the code number for the required packing form: - For crimped leads (0,15 to 1,5 nF): Ammo pack = 249, reel = 149, untaped = 010 - For straight leads (2,2 to 6,8 nF): Ammo pack = 289, reel = 189 - The ordering code for untaped components ends after the tolerance code letter. 2) Capacitance tolerance: 10 % = K 132 Siemens Matsushita Components /u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32660 Special dimensions available upon request. For corresponding design rules, refer to page 238. /u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32660 B 32 660 MKP 7,5 Technical data Climatic category in accordance with IEC 68-1 Lower category temperature Tmin Upper category temperature Tmax Damp heat test Limit values after damp heat test Reliability: Reference conditions Failure rate Service life Failure criteria: Total failure Failure due to variation of parameters DC test voltage Category voltage VC Operation with dc voltage or ac voltage Vrms up to 1 kHz Dissipation factor tan (in 10-3) at 20 C (upper limit values) Insulation resistance Ris or time constant = CR Ris at 20 C, rel. humidity 65 % (minimum as-delivered values) Maximum permissible voltage change per unit of time for non-sinusoidal voltages (pulse, sawtooth) Siemens Matsushita Components 55/100/56 - 55 C + 100 C 56 days/40 C/93 % relative humidity Capacitance change |C/C| 3% Dissipation factor change tan 0,5 10-3 (at 1 kHz) 1,0 10-3 (at 10 kHz) Insulation resistance Ris 50 % of minimum or time constant = CR Ris as-delivered values 0,5 VR; 40 C 1 10-9/h = 2 fit For a conversion table for other operating conditions and temperatures, refer to page 276. 200 000 h Short circuit or open circuit Capacitance change |C/C| > 10 % Dissipation factor tan > 4 upper limit value Insulation resistance Ris < 1500 M(CR 0,33 F) or time constant = CR Ris < 500 s (CR > 0,33 F) 1,4 VR, 2 s T 85 C: VC = 1,0 VR or 1,0 Vrms T = 100 C: VC = 0,7 VR or 0,7 Vrms at 100 kHz: 4 10-3 100 G Max. rate of voltage rise Vpp/ (for Vpp = VR) 0,15 ...1,0 nF 7000 V/s 1,5 ... 6,8 nF 5000 V/s Pulse characteristic k0 in (for Vpp VR) 14 000 000 V2/s 10 000 000 V2/s 133 MKP B 32 660 7,5 Permissible ac voltage Vrms versus frequency f Lead spacing 7,5 mm 1000 Vdc/ 600 Vac /u/MacEater/data1/frame/SMC/FOLIEN-KOND/FMAS5-ENGLISCH/FK.B32660 1000 Vdc/ 450 Vac 134 Siemens Matsushita Components