1
RH119
High Performance
Dual Comparator
The RH119 dual comparator features low input offset
voltage and offset current, high voltage gain, guaranteed
common mode rejection and input protection diodes.
The RH119 is capable of operation over a supply range
from 5V to ±15V and can drive 25mA loads from each open
collector output. A separate GND pin allows the RH119 to
isolate system grounds.
The wafer lots are processed to Linear Technology’s in-
house Class S flow to yield circuits usable in stringent
military applications.
Supply Voltage ........................................................ 36V
Output to Negative Supply Voltage ......................... 36V
Ground to Negative Supply Voltage ........................ 25V
Ground to Positive Supply Voltage ......................... 18V
Diffierential Input Voltage ....................................... ±5V
Differential Input Current ...................................... ±5mA
Input Voltage (See Note 1)
Output Short-Circuit Duration ............................. 10 sec
Operating Temperature Range .............. 55°C to 125°C
Storage Temperature Range ................. 65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
ABSOLUTE MAXIMUM RATINGS
W
WW
U
DESCRIPTION
U
BUR -I CIRCUIT
U U
TOP VIEW
IN2
V
+
V
IN1
10 9
5
2
6
H PACKAGE
10-LEAD TO-5 METAL CAN
8
4
GND2
+IN2
OUT2
+IN1
GND1
OUT1
7
3
1
+
+
15V
SIDE 1
SIDE 2
10k
10k
100
10k
GND1
GND2
OUT1
OUT2
V+
V
–15V
RH119 BI
TOP VIEW
W PACKAGE
10-LEAD CERPAC
1
5
4
3
2
10
6
7
8
9
OUT1
GND1
+IN1
–IN1
V
V+
–IN2
+IN2
GND2
OUT2
1
2
3
4
5
6
7
TOP VIEW
J PACKAGE
14-LEAD CERDIP
14
13
12
11
10
9
8
NC
NC
GND1
+IN1
IN1
V
OUT2
NC
NC
OUT1
V
+
IN2
+IN2
GND2
PACKAGE I FOR ATIO
UU
W
, LTC and LT are registered trademarks of Linear Technology Corporation.
All other trademarks are the property of their respective owners.
2
RH119
10Krad(Si) 20Krad(Si) 50Krad(Si) 100Krad(Si) 200Krad(Si)
SYMBOL PARAMETER CONDITIONS NOTES MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX UNITS
V
OS
Offset Voltage 4 4 4 4 8 mV
I
OS
Input Offset Current 3 75 100 150 300 500 nA
I
B
Input Bias Current 3 500 750 1000 1500 2000 nA
A
VOL
Large-Signal Voltage Gain 10 10 10 10 5 V/mV
V
SAT
Saturation Voltage V
IN
5mV, I
O
= 25mA 1.5 1.5 1.5 1.5 1.5 V
V
+
4.5V, V
= 0V 0.4 0.4 0.4 0.4 0.4 V
V
IN
6mV,
I
SINK
3.2mA
CMRR Common Mode Rejection 90 90 90 90 90 dB
Ratio
I
S
Positive Supply Current V
S
= ±15V 11.5 11.5 11.5 11.5 11.5 mA
Negative Supply Current V
S
= ±15V 4.5 4.5 4.5 4.5 4.5 mA
Output Leakage Current V
IN
5mV, 2 2 2 2 2 µA
V
OUT
to V
= 35V
T
J
= 25
°
C SUB- SUB-
SYMBOL PARAMETER CONDITIONS NOTES MIN TYP MAX GROUP MIN TYP MAX GROUP UNITS
V
OS
Input Offset Voltage V
S
= ±15V, V
CM
= 0V 4 1 mV
3 7 2,3 mV
CMRR Common Mode Rejection 90 1 dB
Ratio
I
OS
Input Offset Current 3 75 1 100 2,3 nA
I
B
Input Bias Current 500 1 1000 2,3 nA
A
V
Voltage Gain 10 4 V/mV
t
R
Response Time 4 80 200 4 200 5,6 ns
V
SAT
Saturation Voltage V
IN
5mV, I
O
= 25mA 1.5 1 V
V
+
4.5V, V
= 0V
V
IN
6mV, I
SINK
3.2mA
T
A
0°C 0.4 1 0.4 2 V
T
A
0°C 0.6 3 V
Output Leakage Current V
IN
5mV, V
OUT
to V
= 35V 2 1 10 2,3 µA
Input Voltage Range V
S
= ±15V –12 12 1 –12 12 2,3 V
V
+
= 5V, V
= 0V 1 3 1 1 3 2,3 V
Differential Input Voltage ±51 ±5 2.3 V
I
S
Supply Current V
+
= 5V, V
= 0V 4.3 mA
Positive Supply Current V
S
= ±15V 11.5 1 mA
Negative Supply Current V
S
= ±1 5V 4.5 1 mA
–55°C TAJ 125°C
(Preirradiation) (Note 2)
TABLE 1: ELECTRICAL CHARACTERISTICS
TABLE 1A: ELECTRICAL CHARACTERISTICS
(Postirradiation) (Note 5)
3
RH119
ELECTRICAL CHARACTERISTICS
(Continued)
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
Note 1: For supply voltages less than ±15V, the maximum input voltage is
equal to the supply voltage.
Note 2: Unless otherwise noted, supply voltage equals ±15V, V
CM
= 0V
and T
A
= 25°C. The GND pin is grounded. Note that the maximum voltage
allowed between the GND pin and V
+
is 18V. Do not tie the GND pin to V
when the power supply voltage exceeds ±9V. The offset voltage, offset
current and bias current specifications apply for all supply voltages
between ±15V and 5V unless otherwise specified.
Note 3: The offset voltages and currents given are the maximum values
required to drive the output within 1V of either supply with a 1mA load––
thus, these parameters define an error band and take into account the
worst-case effects of voltage gain and input impedance.
Note 4: Response time specified for a 100mV input step with 5mV
overdrive.
Note 5: V
S
= ±15V, V
CM
= 0V, T
A
= 25°C unless otherwise noted.
MIL-STD-883 TEST REQUIREMENTS SUBGROUP
Final Electrical Test Requirements (Method 5004) 1*,2,3,4,5,6
Group A Test Requirements (Method 5005) 1,2,3,4,5,6
Group B End Point Electrical Parameters 1,2,3
(Method 5005)
* PDA Applies to subgroup 1. See PDA Test Notes.
PDA Test Notes
The PDA is specified as 5% based on failures from group A, subgroup 1,
tests after cooldown as the final electrical test in accordance with method
5004 of MIL-STD-883 Class B. The verified failures (including Delta
parameters) of group A, subgroup 1, after burn-in divided by the total
number of devices submitted for burn-in in that lot shall be used to
determine the percent for the lot.
Linear Technology Corporation reserves the right to test to tighter limits
than those given.
TABLE 2: ELECTRICAL TEST REQUIRE E TS
UW
TOTAL DOSE BIAS CIRCUIT
+
+
15V
SIDE 1
SIDE 2
100
10k
10k
10k
10k
GND1
GND2
OUT1
OUT2
V+
V
15V
RH119 TDBC
4
RH119
© LINEAR TECHNOLOGY CORPORATION 1990
LT/LT 0305 REV C • PRINTED IN USA
I.D. No. 66-10-0176 Rev. C 0305
TYPICAL PERFORMANCE CHARACTERISTICS
UW
Input Offset Voltage Input Offset Current
Input Bias Current
Input Offset Voltage
Common Mode Rejection Ratio
Open-Loop Gain
TOTAL DOSE KRAD (Si)
1
INPUT OFFSET VOLTAGE (mV)
6
4
2
0
–2
–4
–6 10 100 1000
RH119 G06
VS = ±15V
RS = 50
TOTAL DOSE KRAD (Si)
1
COMMON MODE REJECTION RATIO (dB)
150
140
130
120
110
100
90 10 100 1000
RH119 G05
V
S
= ±15V
TOTAL DOSE KRAD (Si)
1
OPEN-LOOP GAIN (V/mV)
70
60
50
40
30
20
10 10 100 1000
RH119 G04
VS = ±15V
TOTAL DOSE KRAD (Si)
1
INPUT OFFSET VOLTAGE (mV)
6
4
2
0
–2
–4
–6 10 100 1000
RH119 G01
VS = ±15V
VCM = 0V
RS = 5k
TOTAL DOSE KRAD (Si)
1
INPUT BIAS CURRENT (nA)
2000
1600
1200
800
400
010 100 1000
RH119 G02
V
S
= ±15V
V
CM
= 0V
TOTAL DOSE KRAD (Si)
1
INPUT OFFSET CURRENT (nA)
500
400
300
200
100
0
100 10 100 1000
RH119 G03
VS = ±15V
VCM = 0V
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900
FAX: (408) 434-0507
www.linear.com