SL74HC132
System Logic
Semiconductor
SLS
Quad 2-Input NAND Gate
with Schmitt-Trigger Inputs
High-Performance Silicon-Gate CMOS
The SL74HC132 is identical in pinout to the LS/ALS 132. The device
inputs are compatible with standard CMOS outputs; with pullup
resistors, they are compatible with LS/ALSTTL outputs.
The SL74HC132 can be used to enhance noise immunity or to square
up slowly changing waveforms.
• Outputs Directly Interface to CMOS, NMOS, and TTL
• Operating Voltage Range: 2.0 to 6.0 V
• Low Input Current: 1.0 µA
• High Noise Immunity Characteristic of CMOS Devices
ORDERING INFORMATION
SL74HC132N Plastic
SL74HC132D SOIC
TA = -55° to 125° C for all packages
LOGIC DIAGRAM
PIN 14 =VCC
PIN 7 = GND
PIN ASSIGNMENT
FUNCTION TABLE
Inputs Output
A B Y
L L H
L H H
H L H
H H L
SL74HC132
System Logic
Semiconductor
SLS
MAXIMUM RATINGS*
Symbol Parameter Value Unit
VCC DC Supply Voltage (Referenced to GND) -0.5 to +7.0 V
VIN DC Input Voltage (Referenced to GND) -1.5 to VCC +1.5 V
VOUT DC Output Voltage (Referenced to GND) -0.5 to VCC +0.5 V
IIN DC Input Current, per Pin ±20 mA
IOUT DC Output Current, per Pin ±25 mA
ICC DC Supply Current, VCC and GND Pins ±50 mA
PD Power Dissipation in Still Air, Plastic DIP+
SOIC Package+ 750
500 mW
Tstg Storage Temperature -65 to +150 °C
TL Lead Temperature, 1 mm from Case for 10 Seconds
(Plastic DIP or SOIC Package) 260 °C
*Maximum Ratings are those values beyond which damage to the device may occur.
Functional operation should be restricted to the Recommended Operating Conditions.
+Derating - Plastic DIP: - 10 mW/°C from 65° to 125°C
SOIC Package: : - 7 mW/°C from 65° to 125°C
RECOMMENDED OPERATING CONDITIONS
Symbol Parameter Min Max Unit
VCC DC Supply Voltage (Referenced to GND) 2.0 6.0 V
VIN, VOUT DC Input Voltage, Output Voltage (Referenced to GND) 0 VCC V
TA Operating Temperature, All Package Types -55 +125 °C
tr, tf Input Rise and Fall Time (Figure 1) - no
limit* ns
*When VIN ≈ 0.5VCC, ICC> > quiescent current.
This device contains protection circuitry to guard against damage due to high static voltages or electric
fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated
voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range
GND≤(VIN or VOUT)≤VCC.
Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or V
CC).
Unused outputs must be left open.
SL74HC132
System Logic
Semiconductor
SLS
DC ELECTRICAL CHARACTERISTICS(Voltages Referenced to GND)
VCC Guaranteed Limit
Symbol Parameter Test Conditions V 25 °C
to
-55°C
≤85
°C ≤125
°C Unit
VT+max Maximum Positive-
Going Input
Threshold Voltage
VOUT=0.1 V
IOUT≤ 20 µA 2.0
4.5
6.0
1.5
3.15
4.2
1.5
3.15
4.2
1.5
3.15
4.2
V
VT+min Minimum Positive-
Going Input
Threshold Voltage
VOUT=0.1 V
IOUT ≤ 20 µA 2.0
4.5
6.0
1.0
2.3
3.0
0.95
2.25
2.95
0.95
2.25
2.95
V
VT-max Maximum Negative-
Going Input
Threshold Voltage
VOUT=VCC-0.1 V
IOUT≤ 20 µA 2.0
4.5
6.0
0.9
2.0
2.6
0.95
2.05
2.65
0.95
2.05
2.65
V
VT-min Minimum Negative-
Going Input
Threshold Voltage
VOUT=VCC-0.1 V
IOUT ≤ 20 µA 2.0
4.5
6.0
0.3
0.9
1.2
0.3
0.9
1.2
0.3
0.9
1.2
V
VHmax
Note Maximum Hysteresis
Voltage VOUT=0.1 V or VCC-0.1 V
IOUT ≤ 20 µA 2.0
4.5
6.0
1.2
2.25
3.0
1.2
2.25
3.0
1.2
2.25
3.0
V
VHmin
Note Minimum Hysteresis
Voltage VOUT=0.1 V or VCC-0.1 V
IOUT ≤ 20 µA 2.0
4.5
6.0
0.2
0.4
0.5
0.2
0.4
0.5
0.2
0.4
0.5
V
VOH Minimum High-Level
Output Voltage VIN≤VT-min or VT+max
Iout ≤ 20 µA 2.0
4.5
6.0
1.9
4.4
5.9
1.9
4.4
5.9
1.9
4.4
5.9
V
VIN≤VT-min or VT+max
IOUT ≤ 4.0 mA
IOUT ≤ 5.2 mA
4.5
6.0
3.98
5.48
3.84
5.34
3.7
5.2
VOL Maximum Low-Level
Output Voltage VIN ≥VT+max
IOUT ≤ 20 µA 2.0
4.5
6.0
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
V
VIN≥ VT+max
IOUT ≤ 4.0 mA
IOUT ≤ 5.2 mA
4.5
6.0
0.26
0.26
0.33
0.33
0.4
0.4
IIN Maximum Input
Leakage Current VIN=VCC or GND 6.0 ±0.1 ±1.0 ±1.0 µA
ICC Maximum Quiescent
Supply Current
(per Package)
VIN=VCC or GND
IOUT=0µA 6.0 1.0 10 40 µA
Note. VHmin>(VT+min)-(VT-max); VHmax=(VT+max)+(VT-min).
SL74HC132
System Logic
Semiconductor
SLS
AC ELECTRICAL CHARACTERISTICS(CL=50pF,Input tr=tf=6.0 ns)
VCC Guaranteed Limit
Symbol Parameter V 25 °C to
-55°C ≤85°C ≤125°C Unit
tPLH, tPHL Maximum Propagation Delay, Input A or B to
Output Y (Figures 1 and 2) 2.0
4.5
6.0
125
25
21
155
31
26
190
38
32
ns
tTLH, tTHL Maximum Output Transition Time, Any Output
(Figures 1 and 2) 2.0
4.5
6.0
75
15
13
95
19
16
110
22
19
ns
CIN Maximum Input Capacitance - 10 10 10 pF
Power Dissipation Capacitance (Per Gate) Typical @25°C,VCC=5.0 V
CPD Used to determine the no-load dynamic power
consumption: PD=CPDVCC2f+ICCVCC 24 pF
* Includes all probe and jig capacitance.
Figure 1. Switching Waveforms
Figure 2. Test Circuit
