LNK64x4-64x8 LinkSwitch-3 Family Energy-Efficient, Accurate Primary-Side Regulation CV/CC Switcher for Adapters and Chargers + Product Highlights DC Output Dramatically Simplifies CV/CC Converters * Eliminates optocoupler and all secondary CV/CC control circuitry * Eliminates all control loop compensation circuitry Advanced Performance Features Compensates for transformer inductance tolerances Compensates for input line voltage variations Compensates for cable voltage drop Compensates for external component temperature variations Very accurate IC parameter tolerances using test trimming technology Frequency jittering greatly reduces EMI filter cost Programmable switching frequency up to 85 kHz to reduce transformer size * Minimum operation frequency fixed to improve transient load response * * * * * * * Wide Range High-Voltage DC Input D LinkSwitch-3 FB BP S PI-6907-020515 Figure 1. Typical Application - Not a Simplified Circuit. Advanced Protection/Safety Features * Auto-restart protection reduces power delivered by >90% for output short-circuit and control loop faults (open and shorted components) * Hysteretic thermal shutdown - automatic recovery reduces power Output Power Table1,2,3,4 90-264 VAC supply returns from the field * Meets high-voltage creepage requirements between DRAIN and all other pins both on the PCB and at the package EcoSmartTM- Energy Efficient * Easily meets all global energy efficiency regulations with no added components * No-load consumption at 230 VAC input with bias winding <10 mW for LNK64x4-LNK64x6 and <30 mW for LNK64x7-LNK64x8 * ON/OFF control provides constant efficiency down to very light loads - ideal for CEC regulations * No current sense resistors - maximizes efficiency Green Package * Halogen free and RoHS compliant package Applications Description The LinkSwitchTM-3 family of ICs dramatically simplifies low power CV/ CC charger designs by eliminating an optocoupler and secondary control circuitry. The device introduces a revolutionary control technique to provide very accurate output voltage and current regulation, compen-sating for transformer and internal parameter tolerances along with input voltage variations. The device incorporates a 725 V power MOSFET, a novel ON/OFF control state machine, a high-voltage switched current source for self biasing, frequency jittering, cycle-by-cycle current limit and hysteretic thermal shutdown circuitry onto a monolithic IC. Adapter Open Frame 3.5 W 4.1 W 4.5 W 5.1 W 5.5 W 6.1 W 7.5 W 7.5 W LNK6404D / LNK6424D LNK6405D / LNK6415D / LNK6425D LNK6406D / LNK6416D / LNK6426D / LNK6436D / LNK6446D LNK6407D / LNK6417D / LNK6427D Product5 E (eSIP-7C) and K (eSOP-12B) Packages Adapter Open Frame LNK6407K / LNK6417K / LNK6427K 8.5 W 9W LNK6408K / LNK6418K / LNK6428K / LNK6448K 10 W 10 W LNK6408E / LNK6418E / LNK6428E / LNK6448E 10 W 10 W * Chargers for cell/cordless phones, PDAs, MP3/portable audio devices, adapters, etc. D (SO-8C) Package Product5 Table 1. Output Power Table. Notes: 1. Assumes minimum input DC voltage >90 VDC, KP 1 (Recommend KP 1.15 for accurate CC regulation), >78%, DMAX <55%. 2. Output power capability is reduced if a lower input voltage is used. 3. Minimum continuous power with adequate heat sink measured at 50 C ambient with device junction below 110 C. 4. Assumes bias winding is used to supply BYPASS pin. 5. Package: D: SO-8C, E: eSIP-7C, K: eSOP-12B. www.power.com March 2016 This Product is Covered by Patents and/or Pending Patent Applications. LNK64x4-64x8 REGULATOR 6V BYPASS (BP) FEEDBACK (FB) DRAIN (D) + + VTH - D Q FB OUT tSAMPLE-OUT CABLE DROP COMPENSATION INDUCTANCE CORRECTION - VILIMIT Drive DCMAX FAULT AUTO-RESTART OPEN-LOOP FB 6.5 V Reset STATE MACHINE ILIM VILIMIT 6V 5V THERMAL SHUTDOWN tSAMPLE-INPUT DCMAX tSAMPLE-OUT SAMPLE DELAY tSAMPLE-INPUT OSCILLATOR SOURCE (S) + SOURCE (S) CONSTANT CURRENT ILIM - VILIMIT Current Limit Comparator LEADING EDGE BLANKING PI-6660-020515 Figure 2 Functional Block Diagram. Pin Functional Description DRAIN (D) Pin: This pin is the power MOSFET drain connection. It provides internal operating current for both start-up and steady-state operation. E Package (eSIP-7C) Exposed Pad (On Back Side) Internally Connected to SOURCE Pin BYPASS (BP) Pin: This pin is the connection point for an external 1 mF bypass capacitor for the internally generated 6 V supply. FEEDBACK (FB) Pin: 12345 7 FB 1 8S BP 2 7S D S NC NC BP FB During normal operation, switching of the power MOSFET is controlled by this pin. This pin senses the AC voltage on the bias winding. This control input regulates both the output voltage in CV mode and output current in CC mode based on the flyback voltage of the bias winding. The internal inductance correction circuit uses the forward voltage on the bias winding to sense the bulk capacitor voltage. D Package (SO-8C) 6S D4 Exposed Pad (On Bottom) Internally Connected to SOURCE Pin 5S K Package (eSOP-12B) SOURCE (S) Pin: FB 1 12 S This pin is internally connected to the output MOSFET source for high-voltage power and control circuit common returns. BP 2 11 S NC 3 10 S NC 4 9S 8S D6 7S PI-6906-020515 Figure 3. Pin Configuration. 2 Rev. C 03/16 www.power.com LNK64x4-64x8 LinkSwitch-3 Functional Description The LinkSwitch-3 combines a high-voltage power MOSFET switch with a power supply controller in one device. It uses an ON/OFF control to regulate the output voltage. In addition, the switching frequency is modulated to regulate the output current to provide a constant current characteristic. The LinkSwitch-3 controller consists of an oscillator, feedback (sense and logic) circuit, 6 V regulator, over-temperature protection, frequency jittering, current limit circuit, leading-edge blanking, inductance correction circuitry, frequency control for constant current regulation and ON/OFF state machine for CV control. Inductance Correction Circuitry If the primary magnetizing inductance is either too high or low the converter will automatically compensate for this by adjusting the oscillator frequency. Since this controller is designed to operate in discontinuous-conduction mode the output power is directly proportional to the set primary inductance and its tolerance can be completely compensated with adjustments to the switching frequency. Constant Current (CC) Operation As the output voltage and therefore the flyback voltage across the bias winding ramps up, the FEEDBACK pin voltage increases. The switching frequency is adjusted as the FEEDBACK pin voltage increases to provide a constant output current regulation. The constant current circuit and the inductance correction circuit are designed to operate concurrently in the CC region. Constant Voltage (CV) Operation As the FEEDBACK pin approaches 2 V from the constant current regulation mode, the power supply transitions into CV operation. The switching frequency at this point is at its maximum value, corresponding to the peak power point of the CV/CC characteristic. The controller regulates the FEEDBACK pin voltage to remain at FEEDBACK pin threshold (VFBTH) using an ON/OFF state-machine. The FEEDBACK pin voltage is sampled 2.5 ms after the turn-off of the high-voltage switch. At light loads the current limit is also reduced to decrease the transformer flux density and the FEEDBACK pin sampling is done earlier. Output Cable Compensation This compensation provides a constant output voltage at the end of the cable over the entire load range in CV mode. As the converter load increases from no-load to the peak power point (transition point between CV and CC) the voltage drop introduced across the output cable is compensated by increasing the FEEDBACK pin reference voltage. The controller determines the output load and therefore the correct degree of compensation based on the output of the state machine. The amount of cable drop compensation is determined by the third digit in the device part number. Auto-Restart and Open-Loop Protection In the event of a fault condition such as an output short or an open-loop condition the LinkSwitch-3 enters into an appropriate protection mode as described below. In the event the FEEDBACK pin voltage during the flyback period falls below 0.7 V before the FEEDBACK pin sampling delay (~2.5 ms) for a duration in excess of ~300 ms (auto-restart on-time (t AR-ON) the converter enters into auto-restart, wherein the power MOSFET is disabled for 1500 ms. The auto-restart alternately enables and disables the switching of the power MOSFET until the fault condition is removed. In addition to the conditions for auto-restart described above, if the sensed FEEDBACK pin current during the forward period of the conduction cycle (switch "on" time) falls below 120 mA, the converter annunciates this as an open-loop condition (top resistor in potential divider is open or missing) and reduces the auto-restart time from 300 ms to approximately 6 clock cycles (90 ms), whilst keeping the disable period of 2 seconds. Over-Temperature Protection The thermal shutdown circuitry senses the die temperature. The threshold is set at 142 C typical with a 60 C hysteresis. When the die temperature rises above this threshold (142 C) the power MOSFET is disabled and remains disabled until the die temperature falls by 60 C, at which point the MOSFET is re-enabled. Current Limit The current limit circuit senses the current in the power MOSFET. When this current exceeds the internal threshold (ILIMIT), the power MOSFET is turned off for the remainder of that cycle. The leading edge blanking circuit inhibits the current limit comparator for a short time (tLEB) after the power MOSFET is turned on. This leading edge blanking time has been set so that current spikes caused by capacitance and rectifier reverse recovery time will not cause premature termination of the MOSFET conduction. The LinkSwitch-3 also contains a "di/dt" correction feature to minimize CC variation across the input line range. 6 V Regulator The 6 V regulator charges the bypass capacitor connected to the BYPASS pin to 6 V by drawing a current from the voltage on the DRAIN, whenever the MOSFET is off. The BYPASS pin is the internal supply voltage node. When the MOSFET is on, the device runs off of the energy stored in the bypass capacitor. Extremely low power consumption of the internal circuitry allows the LinkSwitch-3 to operate continuously from the current drawn from the DRAIN pin however for the best no-load input power, the BYPASS pin should be supplied current of IS1 from the bias winding at no-load conditions. A bypass capacitor value of 1 mF is sufficient for both high frequency decoupling and energy storage. 3 www.power.com Rev. C 03/16 LNK64x4-64x8 Applications Example reducing the output diode voltage stress by allowing a greater transformer turns ratio. The device is completely self-powered from the BYPASS pin and decoupling capacitor C7. For the LNK64xx devices, there are 4 options for different amount of cable drop compensation determined by the third digit in the device part number. Table 2 shows the amount of compensation for each device. The LNK644x devices do not provide cable drop compensation. Circuit Description This circuit shown in Figure 4 is configured as a primary-side regulated flyback power supply utilizing the LNK6448K. With an average efficiency of 78% and <30 mW no-load input power this design easily exceeds the most stringent current energy efficiency requirements. Input Filter AC input power is rectified by bridge BR1. The rectified DC is filtered by the bulk storage capacitors C1 and C2. Inductors L2 and L3, together with C1 and C2 form a pi () filter, which attenuates conducted differential-mode EMI noise. This configuration along with Power Integrations transformer E-ShieldTM technology allows this design to meet EMI standard EN55022 class B with good margin without requiring a Y capacitor, even with the output connected to safety earth ground. A ferrite bead for L3 is sufficient especially when the output of the supply is floating. Fuse F1 provides protection against catastrophic failure. NTC (Negative Thermal Coefficient) thermistor RT1 is used to limit the rush current to below the peak specification of BR1 during start-up especially at high-line input voltage. High-line results in the highest current into C1 and C2. F1 and RT1 can be replaced by a single fusible resistor. If the reduction in efficiency is acceptable, a bridge with a higher IFSM rating may also allow removal of RT1. If a fusible resistor is selected, use a flameproof type. It should be suitably rated (typically a wire wound type) to withstand the instantaneous dissipation while the input capacitors charge when first connected to the AC line. LNK6448K Primary The LNK6448K device (U1) incorporates the power switching device, oscillator, CC/CV control engine, start-up, and protection functions. The integrated 725 V MOSFET provides a large drain voltage margin in universal input AC applications, increasing reliability and also 5 T1 EPC17 D1 C3 SBR1045SP5-13 680 F 10 V R3 150 D2 S1ML L TP1 90 - 265 VAC O C1 10 F 400 V N TP2 C2 15 F 400 V D L1 Ferrite Bead (3.5 x 7.6 mm) FL1 C6 470 pF 250 V 6 t Output Regulation The LNK64xx family of devices regulates the output using ON/OFF control in the constant voltage (CV) regulation region of the output characteristic and frequency control for constant current (CC) regulation. The feedback resistors (R6 and R7) were selected using standard 1% resistor values to center both the nominal output voltage and constant current regulation thresholds. LinkSwitch-3 U1 LNK6448K C4 680 F 10 V 5 V, 2 A J1-4 4 6.0 L3 Ferrite Bead (3.5 x 7.6 mm) Figure 4. 115 VAC 230 VAC 3 5.0 R6 44.2 k 1% R5 2.4 D3 RS1ML FB C7 1 F 50 V RTN FL2 BP S J1-1 R2 2.55 k 1% R7 10 k 1% R8 2.37 k 1% C8 10 F 25 V PI-7309-020515 R11 200 k BR1 B10S-G 1000 V RT1 10 Output Rectification The secondary of the transformer is rectified by D1, a 10 A, 45 V Schottky barrier type for higher efficiency, and filtered by C3, L1 and C4. If lower efficiency is acceptable then this can be replaced with a 5 A PN junction diode for lower cost. In this application C3 and C4 are sized to meet the required output voltage ripple specification with a ferrite bead L1, which eliminates the high switching noise on the output. A pre-load resistor R2 is used to meet the regulation specification. If the battery self-discharge is required, the pre-load resistor can be replaced with a series resistor and Zener network. C5 R1 1 nF 10 50 V L2 1 mH F1 1A The rectified and filtered input voltage is applied to one side of the primary winding of T1. The other side of the transformer's primary winding is driven by the integrated MOSFET in U1. The leakage inductance drain voltage spike is limited by an RCD-R clamp consisting of D2, R3, R11, and C6. Output Voltage (V) R10 4.7 k The optional bias supply formed by D3 and C8 provides the operating current for U1 via resistor R8. This reduces the no-load consumption from ~200 mW to <30 mW and also increases light load efficiency. 4.0 3.0 2.0 1.0 0.0 0 PI-7209-020515 0.5 1 1.5 2 2.5 3 Output Current (A) Energy Efficient USB Charger Power Supply (78% Average Efficiency, <30 mW No-load Input Power). 4 Rev. C 03/16 www.power.com LNK64x4-64x8 Key Application Considerations LinkSwitch-3 Layout Considerations Output Power Table 2. Output power capability is reduced if a lower input voltage Circuit Board Layout LinkSwitch-3 is a highly integrated power supply solution that integrates on a single die, both, the controller and the high- voltage MOSFET. The presence of high switching currents and voltages together with analog signals makes it especially important to follow good PCB design practice to ensure stable and trouble free operation of the power supply. See Figure 5 for a recommended circuit board layout for LinkSwitch-3. 3. Minimum continuous power with adequate heat sink measured at When designing a printed circuit board for the LinkSwitch-3 based power supply, it is important to follow the following guidelines: The data sheet maximum output power table (Table 1) repre- sents the maximum practical continuous output power level that can be obtained under the following assumed conditions: 1. Assumes minimum input DC voltage >90 VDC, KP 1 (Recom- mend KP 1.15 for accurate CC regulation), >78%, DMAX <55%. is used. 50 C ambient with device junction below 110 C. 4. Assumes bias winding is used to supply BYPASS pin. Output Tolerance LinkSwitch-3 provides an overall output tolerance (including line, component variation and temperature) of 5% for the output voltage in CV operation and 10% for the output current during CC operation over a junction temperature range of 0 C to 110 C. BYPASS Pin Capacitor Selection A 1 mF BYPASS pin capacitor is recommended. The capacitor voltage rating should be greater than 7 V. The capacitor's dielectric material is not important but tolerance of capacitor should be 50%. The capacitor must be physically located adjacent to the LinkSwitch-3 BYPASS pin. Cable Drop Compensation The amount of output cable compensation is determined by the third digit in the device part number. Table 2 shows the amount of compensation for each LinkSwitch-3 device. The output voltage that is entered into PIXls design spreadsheet is the voltage at the end of the output cable when the power supply is delivering maximum power. The output voltage at the terminals of the supply is the value measured at the end of the cable multiplied by the output voltage change factor. LinkSwitch-3 Output Cable Voltage Drop Compensation Device Output Voltage Change Factor (1%) LNK640x 1.02 LNK641x 1.04 LNK642x 1.06 LNK643x 1.08 LNK644x 1.01 Table 2. Cable Compensation Change Factor vs. Device. Single Point Grounding Use a single point (Kelvin) connection at the negative terminal of the input filter capacitor for the LinkSwitch-3 SOURCE pin and bias winding return. This improves surge capabilities by returning surge currents from the bias winding directly to the input filter capacitor. Bypass Capacitor The BYPASS pin capacitor should be located as close as possible to the SOURCE and BYPASS pins. Feedback Resistors Place the feedback resistors directly at the FEEDBACK pin of the LinkSwitch-3 device. This minimizes noise coupling. Thermal Considerations The copper area connected to the SOURCE pins provides the LinkSwitch-3 heat sink. A good estimate is that the LinkSwitch-3 will dissipate 10% of the output power. Provide enough copper area to keep the SOURCE pin temperature below 110 C is recommended to provide margin for part to part RDS(ON) variation. Secondary Loop Area To minimize leakage inductance and EMI the area of the loop connecting the secondary winding, the output diode and the output filter capacitor should be minimized. In addition, sufficient copper area should be provided at the anode and cathode terminal of the diode for heat sinking. A larger area is preferred at the quiet cathode terminal. A large anode area can increase high frequency radiated EMI. Electrostatic Discharge Spark Gap A spark gap is created between the output and the AC input. The spark gap directs ESD energy from the secondary back to the AC input. The trace from the AC input to the spark gap electrode should be spaced away from other traces to prevent unwanted arcing occurring and possible circuit damage. Drain Clamp Optimization LinkSwitch-3 senses the feedback winding on the primary-side to regulate the output. The voltage that appears on the feedback winding is a reflection of the secondary winding voltage while the internal MOSFET is off. Therefore any leakage inductance induced ringing can affect output regulation. Optimizing the drain clamp to 5 www.power.com Rev. C 03/16 LNK64x4-64x8 Figure 5. PCB (Bottom Layer on Left) (Top Layer on Right) Layout Example Showing 10 W Design using K Package. minimize the high frequency ringing will give the best regulation. Figure 6 shows the desired drain voltage waveform compared to Figure 7 with a large undershoot due to the leakage inductance induced ring. This will reduce the output voltage regulation performance. To reduce this adjust the value of the resistor in series with the clamp diode. 0.7 mA typ.) is the IC supply current and VBP (6.2 V typ.) is the BYPASS pin voltage. The parameters IS2 and VBP are provided in the parameter table of the LinkSwitch-3 data sheet. Diode D3 can be any low cost diode such as FR102, 1N4148 or BAV19/20/21. Addition of a Bias Circuit for Higher Light Load Efficiency and Lower No-load Input Power Consumption As with any power supply design, all LinkSwitch-3 designs should be verified on the bench to make sure that component specifications are not exceeded under worst-case conditions. The addition of a bias circuit can decrease the no-load input power from ~200 mW down to less than 30 mW at 230 VAC input. Light load efficiency also increases which may avoid the need to use a Schottky barrier vs. PN junction output diode while still meeting average efficiency requirements. The power supply schematic shown in Figure 4 has only one winding for both feedback and bias circuit. Diode D3, C8, R5 and R8 form the bias circuit. The feedback winding voltage is designed at 11 V, this provides a high enough voltage to supply the BYPASS pin even during low switching frequency operation at no-load. A 10 mF capacitance value is recommended for C8 to hold up the bias voltage at the low switching frequencies that occur at light to no-load. The capacitor type is not critical but the voltage rating should be above the maximum value of VBIAS. The recommended current into the BYPASS pin is equal to IC supply current (0.6 mA to 0.7 mA) at the minimum bias winding voltage. The BYPASS pin current should not exceed 10 mA at the maximum bias winding voltage. The value of R8 is calculated according to (VBIAS - VBP)/IS2, where VBIAS (10 V typ.) is the voltage across C8, IS2 (0.6 mA to Quick Design Checklist The following minimum set of tests is strongly recommended: 1. Maximum drain voltage - Verify that peak VDS does not exceed 680 V at the highest input voltage and maximum output power. 2. Maximum drain current - At maximum ambient temperature, maximum input voltage and maximum output load, verify drain current waveforms at start-up for any signs of transformer saturation and excessive leading edge current spikes. LinkSwitch-3 has a leading edge blanking time of 170 ns to prevent premature termination of the ON-cycle. 3. Thermal check - At maximum output power, both minimum and maximum input voltage and maximum ambient temperature; verify that temperature specifications are not exceeded for LinkSwitch-3, transformer, output diodes and output capacitors. Enough thermal margin should be allowed for part-to-part variation of the RDS(ON) of LinkSwitch-3, as specified in the data sheet. Design Tools Up-to-date information on design tools can be found at the Power Integrations web site: www.power.com 6 Rev. C 03/16 www.power.com PI-5093-020515 An overshoot is acceptable PI-5094-020515 LNK64x4-64x8 Negative ring may increase output ripple and/or degrade output regulation Figure 6. Desired Drain Voltage Waveform with Minimal Leakage Ringing Undershoot. Figure 7. Undesirable Drain Voltage Waveform with Large Leakage Ring Undershoot. 7 www.power.com Rev. C 03/16 LNK64x4-64x8 Absolute Maximum Ratings(1,5) DRAIN Voltage .........................................................-0.3 V to 725 V DRAIN Pin Peak Current: LNK64x4............................. 400 (600) mA(4) LNK64x5..............................504 (750) mA(4) LNK64x6 .............................654 (980) mA(4) LNK64x7............................ 670 (1003) mA(4) LNK64x8............................ 718 (1076) mA(4) Peak Negative Pulsed Drain Current................................... -100 mA(2) FEEDBACK Pin Voltage .................................................. -0.3 to 9 V(6) FEEDBACK Pin Current..........................................................100 mA BYPASS Pin Voltage......................................................... -0.3 to 9 V BYPASS Pin Current................................................................10 mA Storage Temperature .................................................. -65 to 150 C Operating Junction Temperature(7)................................ -40 to 150 C Lead Temperature...............................................................260 C(3) Notes: 1. All voltages referenced to SOURCE, TA = 25 C. 2. Duration not to exceed 2 ms. 3. 1/16 in. from case for 5 seconds. 4. The higher peak DRAIN current is allowed while the DRAIN voltage is simultaneously less than 400 V. 5. Maximum ratings specified may be applied, one at a time without causing permanent damage to the product. Exposure to Absolute Maximum ratings for extended periods of time may affect product reliability. 6. -1 V for current pulse 5 mA out of the pin and a duration of 500 ns. 7. Normally limited by internal circuitry. Thermal Resistance Thermal Resistance: D Package: (qJA) .............................. 100 C/W(2), 80 C/W(3) (qJC)(1)................................................ 30 C/W E Package (qJA)...................................... 105 (qJC)..........................................2 K Package (qJA) ...................... 45 C/W(6), 38 (qJC)..........................................2 Parameter Symbol C/W(4) C/W(5) C/W(7) C/W(5) Notes: 1. Measured on pin 8 (SOURCE) close to plastic interface. 2. Soldered to 0.36 sq. in. (232 mm2), 2 oz. (610 g/m2) copper clad. 3. Soldered to 1 sq. in. (645 mm2), 2 oz. (610 g/m2) copper clad. 4. Free standing with no heat sink. 5. Measured at the back surface of tab. 6. Soldered (including exposed pad for K package) to typical application PCB with a heat sinking area of 0.36 sq. in. (232 mm2), 2 oz. (610 g/m2) copper clad. 7. Soldered (including exposed pad for K package) to typical application PCB with a heat sinking area of 1 sq. in. (645 mm2), 2 oz. (610 g/m2) copper clad. Conditions SOURCE = 0 V; TJ = 0 to 100 C (Unless Otherwise Specified) Min Typ Max Units 85 kHz Control Functions Programmable Maximum Frequency Minimum Operation Frequency fOSC TJ = 25 C tON x IFB = 1.4 mA-ms See Notes A, F fOSC(MIN) TJ = 25 C VFB = VFBth VFB = VFBth LNK64x4-64x6 350 LNK64x7 760 LNK64x8 560 Hz Frequency Ratio (Constant Current) fRATIO(CC) TJ = 25 C Between VFB = 1.3 V and VFB = 1.9 V 1.42 1.47 1.53 Frequency Ratio (Inductance Correction) fRATIO(IC) Between tON x IFB = 1.4 mA and tON x IFB = 2 mA-ms 1.16 1.21 1.26 Frequency Jitter Maximum Duty Cycle FEEDBACK Pin Voltage DCMAX VFBth Peak-to-Peak Jitter Compared to Average Frequency, TJ = 25 C 7 % See Notes D, E 55 % TJ = 25 C CBP = 1 mF LNK6404/6405/ 6406/6446 LNK6415/6416 1.915 1.940 1.965 1.955 1.980 2.005 V 8 Rev. C 03/16 www.power.com LNK64x4-64x8 Parameter Symbol Conditions SOURCE = 0 V; TJ = 0 to 100 C (Unless Otherwise Specified) Min Typ Max LNK6424/6425/ 6426 1.995 2.020 2.045 6436 2.035 2.060 2.085 LNK6407, LNK6408, LNK6448 1.915 1.940 1.965 LNK6417, LNK6418 1.955 1.980 2.005 LNK6427, LNK6428 1.995 2.020 2.045 1.14 1.22 1.30 Units Control Functions (cont.) FEEDBACK Pin Voltage VFBth TJ = 25 C CBP = 1 mF FEEDBACK Pin Voltage at Turn-Off Threshold VFB(AR) Minimum Switch ON-Time tON(MIN) See Note E FEEDBACK Pin Sampling Delay tFB See Note G IS1 FB Voltage > VFBth (MOSFET Not Switching DRAIN Supply Current IS2 ICH1 Feedback Voltage = VFBth -0.1 V, Switch ON-Time = tON (MOSFET Switching at fOSC) VBP = 0 V BYPASS Pin Charge Current ICH2 VBP = 4 V 700 2.55 V V ns 2.75 2.95 ms 300 380 mA LNK64x4 480 540 LNK64x5 500 560 LNK64x6 550 620 LNK64x7 600 680 LNK64x8 700 780 LNK64x4 -5.2 -4.4 -2.7 LNK64x5 -6.8 -5.8 -3.3 LNK64x6 -7.5 -6.1 -3.5 LNK64x7 -7.5 -6.1 -3.5 LNK64x8 -7.5 -6.1 -3.5 LNK64x4 -5 -2.8 -1.5 LNK64x5 -6.4 -4.0 -1.8 LNK64x6 -7 -4.2 -2 LNK64x7 -7 -4.2 -2.0 LNK64x8 -7 -4.2 -2.0 mA mA BYPASS Pin Voltage VBP 5.65 5.90 6.25 V BYPASS Pin Voltage Hysteresis VBPH 0.70 0.95 1.20 V VSHUNT 6.2 6.4 6.8 V BYPASS Pin Shunt Voltage 9 www.power.com Rev. C 03/16 LNK64x4-64x8 Parameter Symbol Conditions SOURCE = 0 V; TJ = 0 to 100 C (Unless Otherwise Specified) Min Typ Max Units Circuit Protection Current Limit ILIMIT di/dt = 60 mA/ms VBP = 5.9 V TJ = 25 C LNK64x4 232 250 268 di/dt = 75 mA/ms VBP = 5.9 V TJ = 25 C LNK64x5 290 315 340 di/dt = 95 mA/ms VBP = 5.9 V TJ = 25 C LNK64x6 359 390 421 di/dt = 105 mA/ms VBP = 5.9 V TJ = 25 C LNK64x7 390 420 449 di/dt = 120 mA/ms VBP = 5.9 V TJ = 25 C LNK64x8 446 480 513 0.27 0.32 0.38 1.025 Minimum Current Limit Scale Factor ILIMIT(MIN) Normalized Output Current IO TJ = 25 C 0.975 1.000 Leading Edge Blanking Time tLED TJ = 25 C Set Note D 125 170 Thermal Shutdown Temperature tSD 135 142 Thermal Shutdown Hysteresis tSDH mA ns 150 60 C C Output LNK64x4 ID = 96 mA LNK64x5 ID = 105 mA ON-State Resistance RDS(ON) LNK64x6 ID = 105 mA LNK64x7 ID = 96 mA LNK64x8 ID = 105 mA OFF-State Leakage IDSS1 IDSS2 TJ = 25 C 19.7 23.7 TJ = 100 C 30.0 36.0 TJ = 25 C 13.2 15.8 TJ = 100 C 19.8 23.8 TJ = 25 C 7.7 9.3 TJ = 100 C 11.5 13.8 TJ = 25 C 4.8 5.8 TJ = 100 C 7.2 8.5 TJ = 25 C 3.1 3.8 TJ = 100 C 4.6 5.5 VDS = 560 V 50 TJ = 125 C See Note C VDS = 375 V TJ = 50 C W mA 15 10 Rev. C 03/16 www.power.com LNK64x4-64x8 Parameter Symbol Conditions SOURCE = 0 V; TJ = 0 to 100 C (Unless Otherwise Specified) Min BVDSS TJ = 25 C 725 V 50 V Typ Max Units Output (cont.) Breakdown Voltage DRAIN Supply Voltage Auto-Restart ON-Time t AR-ON Auto-Restart OFF-Time t AR-OFF Open-Loop FEEDBACK Pin Current Threshold IOL Open-Loop ON-Time See Notes A, E 300 ms 1.5 s See Note E -90 mA See Note E 90 ms NOTES: A. Auto-restart ON-time is a function of switching frequency programmed by tON x IFB and minimum frequency in CC mode. B. The current limit threshold is compensated to cancel the effect of current limit delay. As a result the output current stays constant across the input line range. C. IDSS1 is the worst-case OFF-state leakage specification at 80% of BVDSS and maximum operating junction temperature. IDSS2 is a typical specification under worst-case application conditions (rectified 265 VAC) for no-load consumption calculations. D. When the duty cycle exceeds DCMAX the LinkSwitch-3 operates in on-time extension mode. E. This parameter is derived from characterization. F. The switching frequency is programmable between 60 kHz to 85 kHz. G. At light load tFB is reduced at 1.8 ms typical. 11 www.power.com Rev. C 03/16 LNK64x4-64x8 Typical Performance Characteristics 0.800 0.600 0.400 0.200 0.000 -40 -15 10 35 60 85 1.000 0.800 0.600 0.400 0.200 0.000 -40 110 135 PI-5086-020515 1.000 1.200 Frequency (Normalized to 25 C) PI-7558-032615 Current Limit (Normalized to 25 C) 1.200 -15 Temperature (C) PI-5087-020515 Frequency Ratio (Normalized to 25 C) 1.000 0.800 0.600 0.400 0.200 -15 10 35 60 85 0.800 0.600 0.400 0.200 -15 0.800 0.600 0.400 0.200 35 60 85 Temperature (C) Figure 12. Feedback Voltage vs. Temperature. 35 60 85 110 135 110 135 Figure 11. Frequency Ratio vs. Temperature (Inductor Current). PI-7559-032615 1.200 Normalized Output Current (Normalized to 25 C) 1.000 10 Temperature (C) PI-5089-020515 Feedback Voltage (Normalized to 25 C) 1.200 10 110 135 1.000 0.000 -40 110 135 Figure 10. Frequency Ratio vs. Temperature (Constant Current). -15 85 1.200 Temperature (C) 0.000 -40 60 Figure 9. Output Frequency vs. Temperature. 1.200 0.000 -40 35 PI-5088-020515 Current Limit vs. Temperature. Frequency Ratio (Normalized to 25 C) Figure 8. 10 Temperature (C) 1.000 0.800 0.600 0.400 0.200 0.000 -40 -15 10 35 60 85 110 135 Temperature (C) Figure 13. Normalized Output Current vs. Temperature. 12 Rev. C 03/16 www.power.com LNK64x4-64x8 1.0 300 Drain Current (mA) PI-2213-020515 Scaling Factors: LNK64x4 1.0 LNK64x5 1.5 LNK64x6 2.5 LNK64x7 4.0 LNK64x8 6.5 250 200 150 100 TCASE=25 C TCASE=100 C 50 0.9 -50 -25 0 25 50 0 75 100 125 150 0 50 6 10 Scaling Factors: LNK64x4 1.0 LNK64x5 1.5 LNK64x6 2.5 LNK64x7 4.0 LNK64x8 6.5 40 Power (mW) Drain Capacitance (pF) Scaling Factors: LNK64x4 1.0 LNK64x5 1.5 LNK64x6 2.5 LNK64x7 4.0 LNK64x8 6.5 100 4 8 10 Figure 15. Output Characteristic. PI-7202-020415 Figure 14. Breakdown vs. Temperature. 1000 2 DRAIN Voltage (V) Junction Temperature (C) PI-7203-020415 Breakdown Voltage (Normalized to 25 C) 1.1 PI-7201-020415 Typical Performance Characteristics (cont.) 30 20 10 0 1 0 100 200 300 400 Drain Voltage (V) Figure 16. COSS vs. Drain Voltage. 500 600 0 200 400 600 DRAIN Voltage (V) Figure 17. Drain Capacitance Power. 13 www.power.com Rev. C 03/16 LNK64x4-64x8 SO-8C (D Package) 4 B 0.10 (0.004) C A-B 2X 2 DETAIL A 4.90 (0.193) BSC A 4 8 D 5 2 3.90 (0.154) BSC GAUGE PLANE SEATING PLANE 6.00 (0.236) BSC o 0-8 C 1.04 (0.041) REF 2X 0.10 (0.004) C D 1 Pin 1 ID 4 0.40 (0.016) 1.27 (0.050) 0.20 (0.008) C 2X 7X 0.31 - 0.51 (0.012 - 0.020) 0.25 (0.010) M C A-B D 1.27 (0.050) BSC 1.35 (0.053) 1.75 (0.069) 0.25 (0.010) BSC 1.25 - 1.65 (0.049 - 0.065) DETAIL A 0.10 (0.004) 0.25 (0.010) 0.10 (0.004) C H 7X SEATING PLANE C Reference Solder Pad Dimensions + 2.00 (0.079) + D07C 0.17 (0.007) 0.25 (0.010) 1.27 (0.050) 4.90 (0.193) + + 0.60 (0.024) Notes: 1. JEDEC reference: MS-012. 2. Package outline exclusive of mold flash and metal burr. 3. Package outline inclusive of plating thickness. 4. Datums A and B to be determined at datum plane H. 5. Controlling dimensions are in millimeters. Inch dimensions are shown in parenthesis. Angles in degrees. PI-4526-012315 14 Rev. C 03/16 www.power.com LNK64x4-64x8 eSIP-7C (E Package) 2 C 0.403 (10.24) 0.397 (10.08) A 0.264 (6.70) Ref. 0.081 (2.06) 0.077 (1.96) B Detail A 2 0.290 (7.37) Ref. 0.519 (13.18) Ref. 0.325 (8.25) 0.320 (8.13) Pin #1 I.D. 0.140 (3.56) 0.120 (3.05) 0.070 (1.78) Ref. 0.050 (1.27) 3 0.016 (0.41) 6x 0.011 (0.28) 0.020 M 0.51 M C FRONT VIEW 10 Ref. All Around 0.198 (5.04) Ref. 0.207 (5.26) 0.187 (4.75) 0.016 (0.41) Ref. 3 0.047 (1.19) 4 0.033 (0.84) 6x 0.028 (0.71) 0.010 M 0.25 M C A B 0.100 (2.54) 0.118 (3.00) BACK VIEW SIDE VIEW 0.100 (2.54) 0.021 (0.53) 0.019 (0.48) 0.050 (1.27) 0.020 (0.50) 0.060 (1.52) Ref. 0.050 (1.27) PIN 1 0.378 (9.60) Ref. 0.048 (1.22) 0.046 (1.17) 0.059 (1.50) 0.019 (0.48) Ref. 0.155 (3.93) 0.023 (0.58) END VIEW PIN 7 0.027 (0.70) 0.059 (1.50) DETAIL A Notes: 1. Dimensioning and tolerancing per ASME Y14.5M-1994. 2. Dimensions noted are determined at the outermost extremes of the plastic body exclusive of mold flash, tie bar burrs, gate burrs, and interlead flash, but including any mismatch between the top and bottom of the plastic body. Maximum mold protrusion is 0.007 [0.18] per side. 0.100 (2.54) 0.100 (2.54) MOUNTING HOLE PATTERN (not to scale) 3. Dimensions noted are inclusive of plating thickness. 4. Does not include inter-lead flash or protrusions. 5. Controlling dimensions in inches (mm). PI-4917-020515 15 www.power.com Rev. C 03/16 LNK64x4-64x8 eSOP-12B (K Package) 2 0.004 [0.10] C A 2X 0.400 [10.16] Pin #1 I.D. (Laser Marked) 0.356 [9.04] Ref. 0.325 [8.26] Max. 7 2X 7 0.004 [0.10] C B 0.059 [1.50] Ref, Typ 12 2 0.008 [0.20] C 1 2X, 5/6 Lead Tips 2 3 4 B 6 Gauge Plane 0 - 8 6 1 BOTTOM VIEW 0.092 [2.34] 0.086 [2.18] 0.032 [0.80] 0.029 [0.72] 0.006 [0.15] 0.000 [0.00] 0.004 [0.10] C C Seating Plane Detail A Seating plane to package bottom standoff 0.217 [5.51] 3 0.019 [0.48] Ref. 0.022 [0.56] Ref. 0.016 [0.41] 0.011 [0.28] 11x 0.306 [7.77] Ref. END VIEW SIDE VIEW 0.067 [1.70] C 0.049 [1.23] 0.046 [1.16] 0.028 [0.71] Ref. 0.020 [0.51] Ref. 0.098 [2.49] 0.086 [2.18] Seating Plane 0.034 [0.85] 0.026 [0.65] DETAIL A (Scale = 9X) 3 4 0.120 [3.05] Ref 0.023 [0.58] 11x 0.018 [0.46] 0.070 [1.78] 0.010 (0.25) M C A B TOP VIEW H 0.010 [0.25] 0.225 [5.72] Max. 7 0.350 [8.89] 0.059 [1.50] Ref, Typ 0.460 [11.68] 0.010 [0.25] Ref. 0.055 [1.40] Ref. Land Pattern Dimensions 1 12 2 11 3 10 4 9 0.028 [0.71] 0.321 [8.15] Notes: 1. Dimensioning and tolerancing per ASME Y14.5M-1994. 2. Dimensions noted are determined at the outermost extremes of the plastic body exclusive of mold flash, tie bar burrs, gate burrs, and interlead flash, but including any mismatch between the top and bottom of the plastic body. Maximum mold protrusion is 0.007 [0.18] per side. 3. Dimensions noted are inclusive of plating thickness. 4. Does not include interlead flash or protrusions. 5. Controlling dimensions in inches [mm]. 6 0.429 [10.90] 8 6. Datums A and B to be determined at Datum H. 7 7. Exposed pad is nominally located at the centerline of Datums A and B. "Max" dimensions noted include both size and positional tolerances. PI-5748a-020515 16 Rev. C 03/16 www.power.com LNK64x4-64x8 Part Ordering Information * LinkSwitch Product Family * 3 Series Number * Package Identifier D SO-8C E eSIP-7C K eSOP-12B * Tape & Reel and Other Options Blank LNK 64x7 D - TL TL Standard Configuration Tape & Reel, 2.5 k pcs for D package, 1 k pcs for K package. 17 www.power.com Rev. C 03/16 Revision Notes Date A Code A. 10/16/13 A Specified Max BYPASS Pin Current. 03/13/14 A Code L. Updated Table 1 and Table 2. 06/11/14 B Added LNK64x4, 64x5 and 64x6 parts. Updated fRATIO(CC), ILIMIT(MIN), tFB, VFB(AR), fOSC(MIN), t AR-OFF and IOL. Updated ms values in Auto-Restart section on page 3. Removed fOSC(AR) and updated t AR-ON. 03/31/15 C Added Note G on page 11. 03/16 For the latest updates, visit our website: www.power.com Power Integrations reserves the right to make changes to its products at any time to improve reliability or manufacturability. Power Integrations does not assume any liability arising from the use of any device or circuit described herein. POWER INTEGRATIONS MAKES NO WARRANTY HEREIN AND SPECIFICALLY DISCLAIMS ALL WARRANTIES INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS. Patent Information The products and applications illustrated herein (including transformer construction and circuits external to the products) may be covered by one or more U.S. and foreign patents, or potentially by pending U.S. and foreign patent applications assigned to Power Integrations. A complete list of Power Integrations patents may be found at www.power.com. Power Integrations grants its customers a license under certain patent rights as set forth at http://www.power.com/ip.htm. Life Support Policy POWER INTEGRATIONS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF POWER INTEGRATIONS. As used herein: 1. A Life support device or system is one which, (i) is intended for surgical implant into the body, or (ii) supports or sustains life, and (iii) whose failure to perform, when properly used in accordance with instructions for use, can be reasonably expected to result in significant injury or death to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. The PI logo, TOPSwitch, TinySwitch, LinkSwitch, LYTSwitch, InnoSwitch, DPA-Switch, PeakSwitch, CAPZero, SENZero, LinkZero, HiperPFS, HiperTFS, HiperLCS, Qspeed, EcoSmart, Clampless, E-Shield, Filterfuse, FluxLink, StakFET, PI Expert and PI FACTS are trademarks of Power Integrations, Inc. Other trademarks are property of their respective companies. (c)2016, Power Integrations, Inc. Power Integrations Worldwide Sales Support Locations World Headquarters 5245 Hellyer Avenue San Jose, CA 95138, USA. Main: +1-408-414-9200 Customer Service: Phone: +1-408-414-9665 Fax: +1-408-414-9765 e-mail: usasales@power.com China (Shanghai) Rm 2410, Charity Plaza, No. 88 North Caoxi Road Shanghai, PRC 200030 Phone: +86-21-6354-6323 Fax: +86-21-6354-6325 e-mail: chinasales@power.com China (Shenzhen) 17/F, Hivac Building, No. 2, Keji Nan 8th Road, Nanshan District, Shenzhen, China, 518057 Phone: +86-755-8672-8689 Fax: +86-755-8672-8690 e-mail: chinasales@power.com Germany Lindwurmstrasse 114 80337 Munich Germany Phone: +49-895-527-39110 Fax: +49-895-527-39200 e-mail: eurosales@power.com India #1, 14th Main Road Vasanthanagar Bangalore-560052 India Phone: +91-80-4113-8020 Fax: +91-80-4113-8023 e-mail: indiasales@power.com Italy Via Milanese 20, 3rd. Fl. 20099 Sesto San Giovanni (MI) Italy Phone: +39-024-550-8701 Fax: +39-028-928-6009 e-mail: eurosales@power.com Japan Kosei Dai-3 Bldg. 2-12-11, Shin-Yokohama, Kohoku-ku Yokohama-shi, Kanagawa 222-0033 Japan Phone: +81-45-471-1021 Fax: +81-45-471-3717 e-mail: japansales@power.com Taiwan 5F, No. 318, Nei Hu Rd., Sec. 1 Nei Hu Dist. Taipei 11493, Taiwan R.O.C. Phone: +886-2-2659-4570 Fax: +886-2-2659-4550 e-mail: taiwansales@power.com UK Cambridge Semiconductor, Korea a Power Integrations company RM 602, 6FL Westbrook Centre, Block 5, 2nd Floor Korea City Air Terminal B/D, 159-6 Milton Road Samsung-Dong, Kangnam-Gu, Cambridge CB4 1YG Seoul, 135-728, Korea Phone: +44 (0) 1223-446483 Phone: +82-2-2016-6610 e-mail: eurosales@power.com Fax: +82-2-2016-6630 e-mail: koreasales@power.com Singapore 51 Newton Road #19-01/05 Goldhill Plaza Singapore, 308900 Phone: +65-6358-2160 Fax: +65-6358-2015 e-mail: singaporesales@power.com